about pushover analysis and sap 2000 method
DESCRIPTION
*Pushover Analysis*SAP 2000TRANSCRIPT
![Page 1: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/1.jpg)
4/5/2012
1
Using SAP2000 Software Package in Earthquake Engineering (Part II: Pushover)
Same frame but different loading
QD = 4.5 kips/ft
QD = 10.5 kips/ft
QD = 10.5 kips/ft
Loads on structures:- Static (e.g. self-weight)- Dynamic (e.g. earthquake)
Structures’ response:Linear (constant stiffness)- Linear (constant stiffness)
- Nonlinear (variable stiffness)
→Structural Analysis Approaches:- Linear static (ELF)(least accurate; least complex)( p )
- Linear dynamic (response spectra)- Nonlinear static (pushover)- Nonlinear dynamic (time history)(most accurate; most complex)
![Page 2: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/2.jpg)
4/5/2012
2
Pushover analysis:Applying a force distributionforce distribution to the structure in an incremental fashion while monitoring the occurrence of nonlinear behaviornonlinear behavior and plotting the base shear (Vb) versus control nodecontrol node displacement (uN).
compromise the simplicity of linear static approaches and accuracy of nonlinear dynamic methods.
1- Nonlinearity sources: - Geometrical (P-Delta effects)
(consider or not: codes)- Material(too many material’s behavior models)(too many material’s behavior models)
2- Nonlinearity modeling: - Concentrated - Distributed
![Page 3: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/3.jpg)
4/5/2012
3
Plastic hinge properties: - running section analysis and coming up with M-φ curves
Plastic hinge properties: - using codes’ tabulated properties
![Page 4: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/4.jpg)
4/5/2012
4
3- Lateral load pattern: - a single concentrated force at the top(good for one-story buildings)
- in proportion to the standard code procedure:
in proportion to the product of story masses and
/x x x x xF w h w h V
- in proportion to the product of story masses and predominant mode shape of the elastic model of the structure
/x x x x xF w w V
4- Control node: - For common buildings, the control node could be selected as roof (top) story node
h l i i d h h h- Pushover analysis is stopped when the structure reaches:pre-defined displacementorultimate capacity
5- Gravity loads should be applied prior to the application of lateral loads
![Page 5: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/5.jpg)
4/5/2012
5
6- Check at performance point : The global response of the structure and individual component deformations are compared to limits in li ht f th ifi f l f th tlight of the specific performance goals of the system
Using SAP2000 for Pushover Analysis
We will use the same frame (elastic beams), just modify dead loads:
![Page 6: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/6.jpg)
4/5/2012
6
1- Run Modal Analysis
( 1 )
1 . 0
0 . 7 5 9 0 . 3 4 5
1 0 0 0
Select lateral load pattern:
7 5 9
3 4 5xF k i p s
2- Lateral Load Case
![Page 7: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/7.jpg)
4/5/2012
7
3- Modify Dead Load Case
3- Define Push Load Case
1
2
![Page 8: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/8.jpg)
4/5/2012
8
3- Define Push Load Case
1 2
4- Assign Plastic Hinges
Select column elements:
![Page 9: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/9.jpg)
4/5/2012
9
4- Assign Plastic Hinges
4- Assign Plastic Hinges
Select beam elements:
![Page 10: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/10.jpg)
4/5/2012
10
5- Run
6- Results Output
Display displacement:
![Page 11: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/11.jpg)
4/5/2012
11
6- Results Output
Display pushover curve:
7- Checking Hinges Status
Looking for 0.5 ft roof displacement:
![Page 12: About Pushover Analysis and SAP 2000 Method](https://reader034.vdocuments.net/reader034/viewer/2022042502/545fc9ceaf795949708b4d9e/html5/thumbnails/12.jpg)
4/5/2012
12
7- Checking Hinges Status
At 0.5 ft roof displacement: the performance level of the system is Collapse Prevention (CP)