abstrak sifat elastis dan anisotropi formasi … · analisis hubungan antara sifat elastis dan...
TRANSCRIPT
i
ABSTRAK
SIFAT ELASTIS DAN ANISOTROPI FORMASI TALANG
AKAR – CEKUNGAN SUMATRA SELATAN BERDASARKAN
PENGUKURAN TOMOGRAFI ULTRASONIK BATUAN INTI
Oleh
Vani Mutia Sari
NIM: 32313001
(Program Studi Doktor Teknik Geofisika)
Formasi Talang Akar (TAF) merupakan batuan induk dan reservoir utama di
Cekungan Sumatra Selatan, yang merupakan salah satu cekungan yang kaya akan
hidrokarbon di kawasan barat Indonesia. Pengolahan, pemodelan, dan interpretasi
data seismik yang baik pada TAF memerlukan pengetahuan tentang efek
anisotropi, serta hubungannya dengan parameter fisik batuan induk dan reservoir.
Namun, sampai saat ini belum ada studi lengkap mengenai anisotropi seismik
pada batuan induk dan reservoir TAF.
Studi anisotropi sulit dilakukan pada TAF di Cekungan Sumatra Selatan karena
tidak tersedianya data dipole shear-velocity log (log Vs), dan seismik tiga
komponen. Oleh karena itu, parameter anisotropi pada penelitian ini diperoleh
dari pengukuran laboratorium pada contoh batuan inti. Kondisi batuan inti TAF
yang sangat rapuh, pecah-pecah dan jumlah contoh terbatas, serta struktur mikro
batuan TAF yang berada di bawah resolusi gelombang seismik menjadikan
gelombang ultrasonik sebagai pilihan terbaik untuk pegukuran anisotropi.
Pengukuran tomografi ultrasonik dengan konfigurasi sumber-penerima 3600 dan
gelombang ultrasonik resolusi tinggi dapat memberikan hasil yang lebih tepat
mengenai sifat elastis dan parameter anisotropi batuan.
Penelitian ini dibagi dalam empat tahapan utama, yaitu pengukuran tomografi
ultrasonik, analisis sifat elastis, analisis shear wave splitting dan anisotropi, serta
analisis hubungan antara sifat elastis dan parameter anisotropi dengan jenis
batuan, porositas batuan inti, porositas sayatan tipis, dan sand-volume ratio.
Penelitian dilakukan pada 21 contoh batuan TAF dari 6 sumur di cekungan
Sumatra Selatan. Berdasarkan analisis petrografi, 21 contoh batuan inti tersebut
terdiri dari mud, silt, sandy silt, sandy clay, dan clayey sand. Korelasi dari
beberapa parameter yang dilakukan pada penelitian ini menunjukkan bahwa
semua contoh batuan inti TAF adalah anisotrop, dan terdapat hubungan linear
antara parameter anisotropi gelombang P (ε) dan parameter anisotropi gelombang
S (γ). Hubungan antara parameter anisotropi ε dan γ terhadap sand-volume ratio
juga linear, dan dapat dipisahkan menjadi dua kelompok: sand-volume ratio
rendah (<0.50) dan sand-volume ratio tinggi (>0.50). γ memperlihatkan korelasi
terbaik untuk kedua kelompok tersebut. Parameter anisotropi contoh batuan inti
ii
juga dipengaruhi oleh posisi contoh batuan inti terhadap struktur geologi di
sekitarnya.
Kata kunci: parameter anisotropi, tomografi ultrasonik, sand-volume ratio
iii
ABSTRACT
ELASTIC AND ANISOTROPY PARAMETERS OF THE TALANG
AKAR FORMATION – SOUTH SUMATRA BASIN BASED ON
ULTRASONIC TOMOGRAPHY OF CORE PLUGS
By
Vani Mutia Sari
NIM: 32313001
(Doctoral Program in Geophysical Engineering)
Talang Akar Formation (TAF) is the main source and reservoir rocks in South
Sumatra Basin, which is one of the hidrocarbon-rich basins in western Indonesia.
A good seismic data processing, modeling and interpretation needs to account the
rock anisotropy effect, and its relationship to the physical parameters of the
source and reservoir rocks. However, up to now there is no solid study on the
seismic anisotropy of the TAF reservoir and source rocks.
Anisotropy study is difficult to be done in the South Sumatra Basin’s TAF due to
the unavailability of dipole sonic log and three-component seismic data.
Therefore, the anisotropy parameters in this study were obtained from laboratory
measurements on core plug samples. As the limited core plug samples were
friable, fissured, and its microstructure is below the seismic wave resolution, then
the ultrasonic wave was used to measure the TAF core plugs anisotropies.
Furthermore, the ultrasonic tomography measurements with 3600
source-receiver
configurations and high-resolution ultrasound gives a more precise results of
elastic properties and anisotropy parameters.
This study is divided into four main steps: ultrasonic tomography measurements,
analysis of elastic properties, shear wave splitting analysis and anisotropy, and
analysis on the relationships of elastic properties and anisotropy parameters with
rock-type, core-plug porosity, thin-section porosity, and sand-volume ratio.
The study was done on 21 core-plug samples collected from 6 wells in the South
Sumatra Basin. Petrographic analysis shows that the rock types of the 21 samples
are mud, silt, sandy silt, sandy clay, and clayey sand. The relationship of several
parameters shows that all of the samples are anisotropic, and there is a linear
relationship between the P-wave anisotropy parameter (ε) and the S-wave
anisotropy (γ). The cross-plots of the anisotropy parameters ε and γ to the sand-
volume ratio show that they have linear relationships and can be classified into
two groups: low sand-volume ratio (<0.50), and high sand-volume ratio (>0.50).
Anisotropy parameter γ give better correlation for both groups. The anisotropy
parameters of the samples were also affected by the position of core samples to
the geology structures around it.
Keywords: anisotropy parameters, ultrasonic tomography, sand-volume ratio