access class control(eran8.1_03)
TRANSCRIPT
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 1/90
eRAN
Access Class Control Feature
Parameter Description
Issue 03
Date 2015-11-03
HUAWEI TECHNOLOGIES CO., LTD.
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 2/90
Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 3/90
Contents
1 About This Document.................................................................................................................. 1
1.1 Scope.............................................................................................................................................................................. 1
1.2 Intended Audience..........................................................................................................................................................1
1.3 Change History...............................................................................................................................................................2
1.4 Differences Between eNodeB Types..............................................................................................................................4
2 Overview......................................................................................................................................... 5
2.1 Introduction.................................................................................................................................................................... 5
2.2 Benefits...........................................................................................................................................................................5
2.3 Architecture.................................................................................................................................................................... 6
3 Technical Description...................................................................................................................8
3.1 Related Concepts............................................................................................................................................................8
3.2 Static AC Control......................................................................................................................................................... 10
3.2.1 Static AC Control Procedure..................................................................................................................................... 103.2.2 Access Decision Procedure........................................................................................................................................11
3.3 Intelligent AC Control..................................................................................................................................................19
3.3.1 Intelligent AC Control Procedure..............................................................................................................................19
3.3.2 Implementation Principles.........................................................................................................................................20
3.4 Dynamic SSAC.............................................................................................................................................................23
3.4.1 Dynamic SSAC Procedure........................................................................................................................................ 23
3.4.2 Implementation Principles.........................................................................................................................................24
4 Related Features...........................................................................................................................27
4.1 Features R elated to LOFD-070207 Intelligent Access Class Control..........................................................................27
4.2 Features Related to LOFD-008002 Dynamic Service-specific Access Control...........................................................27
5 Network Impact........................................................................................................................... 29
5.1 LOFD-070207 Intelligent Access Class Control..........................................................................................................29
5.2 LOFD-008002 Dynamic Service-specific Access Control...........................................................................................29
6 Engineering Guidelines............................................................................................................. 30
6.1 Static AC control.......................................................................................................................................................... 30
6.1.1 When to Use Static AC Control................................................................................................................................ 30
6.1.2 Required Information................................................................................................................................................ 30
6.1.3 Planning.....................................................................................................................................................................30
eRAN
Access Class Control Feature Parameter Description Contents
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 4/90
6.1.3.1 RF Planning............................................................................................................................................................30
6.1.3.2 Network Planning...................................................................................................................................................30
6.1.3.3 Hardware Planning................................................................................................................................................. 30
6.1.4 Deployment............................................................................................................................................................... 30
6.1.4.1 Requirements..........................................................................................................................................................31
6.1.4.2 Data Preparation..................................................................................................................................................... 31
6.1.4.3 Activation............................................................................................................................................................... 37
6.1.4.4 Activation Observation...........................................................................................................................................39
6.1.4.5 Reconfiguration...................................................................................................................................................... 40
6.1.4.6 Deactivation............................................................................................................................................................40
6.1.5 Performance Monitoring............................................................................................................................................41
6.1.6 Parameter Optimization.............................................................................................................................................41
6.1.7 Troubleshooting.........................................................................................................................................................41
6.2 Intelligent AC control...................................................................................................................................................41
6.2.1 When to Use Intelligent AC Control......................................................................................................................... 41
6.2.2 Required Information................................................................................................................................................ 42
6.2.3 Planning.....................................................................................................................................................................42
6.2.3.1 RF Planning............................................................................................................................................................42
6.2.3.2 Network Planning...................................................................................................................................................42
6.2.3.3 Hardware Planning................................................................................................................................................. 42
6.2.4 Deployment............................................................................................................................................................... 42
6.2.4.1 Requir ements..........................................................................................................................................................42
6.2.4.2 Data Preparation..................................................................................................................................................... 426.2.4.3 Activation............................................................................................................................................................... 45
6.2.4.4 Activation Observation...........................................................................................................................................47
6.2.4.5 Reconfiguration...................................................................................................................................................... 47
6.2.4.6 Deactivation............................................................................................................................................................47
6.2.5 Performance Monitoring............................................................................................................................................47
6.2.6 Parameter Optimization.............................................................................................................................................47
6.2.7 Troubleshooting.........................................................................................................................................................48
6.3 Dynamic SSAC.............................................................................................................................................................48
6.3.1 When to Use Dynamic SSAC....................................................................................................................................48
6.3.2 Required Information................................................................................................................................................ 49
6.3.3 Planning.....................................................................................................................................................................49
6.3.3.1 RF Planning............................................................................................................................................................49
6.3.3.2 Network Planning...................................................................................................................................................49
6.3.3.3 Hardware Planning................................................................................................................................................. 49
6.3.4 Deployment............................................................................................................................................................... 49
6.3.4.1 Requir ements..........................................................................................................................................................49
6.3.4.2 Data Preparation..................................................................................................................................................... 50
6.3.4.3 Activation............................................................................................................................................................... 52
6.3.4.4 Activation Observation...........................................................................................................................................54
eRAN
Access Class Control Feature Parameter Description Contents
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iii
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 5/90
6.3.4.5 Reconfiguration...................................................................................................................................................... 54
6.3.4.6 Deactivation............................................................................................................................................................54
6.3.5 Performance Monitoring............................................................................................................................................54
6.3.6 Parameter Optimization.............................................................................................................................................55
6.3.7 Troubleshooting.........................................................................................................................................................55
7 Parameters.....................................................................................................................................57
8 Counters........................................................................................................................................ 80
9 Glossary.........................................................................................................................................84
10 Reference Documents...............................................................................................................85
eRAN
Access Class Control Feature Parameter Description Contents
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iv
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 6/90
1 About This Document
1.1 Scope
This document describes access class (AC) control, including its technical principles, related
features, network impact, and engineering guidelines.
This document covers the following features:
l LOFD-070207 Intelligent Access Class Control
l LOFD-008002 Dynamic Service-specific Access Control
Any managed objects (MOs), parameters, alarms, or counters described herein correspond to
the software release delivered with this document. Any future updates will be described in the product documentation delivered with future software releases.
This document applies only to LTE FDD. Any "LTE" in this document refers to LTE FDD,
and "eNodeB" refers to LTE FDD eNodeB.
This document applies to the following types of eNodeBs.
eNodeB Type Model
Macro 3900 series eNodeB
Micro BTS3202E
LampSite DBS3900 LampSite
1.2 Intended Audience
This document is intended for personnel who:
l Need to understand access class control
l Work with Huawei products
eRAN
Access Class Control Feature Parameter Description 1 About This Document
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 7/90
1.3 Change History
This section provides information about the changes in different document versions. There are
two types of changes:
l Feature change
Changes in features and parameters of a specified version as well as the affected entities
l Editorial change
Changes in wording or addition of information and any related parameters affected by
editorial changes. Editorial change does not specify the affected entities.
eRAN8.1 03 (2015-11-03)
This issue includes the following changes.
ChangeType
Change Description Parameter Change Affected Entity
Feature
change
None None N/A
Editorial
change
Revised some descriptions in
the document.
None N/A
eRAN8.1 02 (2015-06-30)
This issue includes the following changes.
Change Type Change Description ParameterChange
AffectedEntity
Feature change None None N/A
Editorial
change
l Reorganized this document.
l Revised descriptions in the following
sections:
– 2.1 Introduction
– 2.2 Benefits
– 3.3.2 Implementation Principles
– 3.4.2 Implementation Principles
– 5.2 LOFD-008002 Dynamic
Service-specific Access Control
– 6 Engineering Guidelines
None N/A
eRAN
Access Class Control Feature Parameter Description 1 About This Document
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 8/90
eRAN8.1 01 (2015-03-23)
This issue does not include any changes.
eRAN8.1 Draft A (2015-01-15)Compared with Issue 01 (2014-04-26) of eRAN7.0, Draft A (2015-01-15) of eRAN8.1
includes the following changes.
ChangeType
Change Description Parameter Change Affected Entity
Feature
change
Added LOFD-008002
Dynamic Service-
specific Access
Control. For details
about this feature, see
3.4 Dynamic SSACand 6 Engineering
Guidelines.
Added the following
parameters:
l CellAlgoSwitch. AcBarAlg
oforDynSwitch
l CellDynAcBarAlgo-Para. DisasterReferenceInd
l CellDynAcBarAlgo-
Para. DisasterDuration
l CellDynAcBarAlgo-
Para. SsacTriggerCondSa-
tiPeriods
l CellDynAcBarAlgo-
Para. SsacCancelCondSati-
Periods
Macro, micro,
and LampSite
eNodeBs
Optimized themechanisms for
triggering and
canceling intelligent
AC control. For details,
see 3.3 Intelligent AC
Control and 6
Engineering
Guidelines.
Added the following parameters:
l CellDynAcBarAlgo-
Para. MoTriggerCondSati-
Periods
l CellDynAcBarAlgo-
Para. MoCancelCondSati-
Periods
Macro, micro,and LampSite
eNodeBs
Added the policy
options for determining
whether a cell iscongested. For details,
see 3.3.2
Implementation
Principles and 3.4.2
Implementation
Principles.
Added the following
parameters:
l EnodebFlowCtrlPara. Dyn AcBarPolicyMode
l EnodebFlowCtrlPara.Cpu
LoadThd
Macro, micro,
and LampSite
eNodeBs
Editorial
change
Revised the description
in this document.
None N/A
eRAN
Access Class Control Feature Parameter Description 1 About This Document
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 9/90
1.4 Differences Between eNodeB Types
Feature Support by Macro, Micro, and LampSite eNodeBs
Feature ID FeatureName
Supported byMacroeNodeBs
Supported byMicroeNodeBs
Supported byLampSiteeNodeBs
LOFD-070207 Intelligent
Access Class
Control
Yes Yes Yes
LOFD-008002 Dynamic
Service-
specific Access
Control
Yes Yes Yes
Function Implementation in Macro, Micro, and LampSite eNodeBs
Function Difference
Triggering of flow
control in
intelligent AC
control
For macro eNodeBs, flow control is triggered by a large amount of
RRC signaling or RACH signaling. For micro eNodeBs, flow control
is triggered only by a large amount of RACH signaling. For details,
see 3.3.2 Implementation Principles.
eRAN
Access Class Control Feature Parameter Description 1 About This Document
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 10/90
2 Overview
2.1 Introduction
Access class (AC) control is used to manage UE access to a network, as defined by 3GPP.
With AC control, the eNodeB broadcasts AC control parameters using system information
block type 2 (SIB2) to all UEs in a cell. According to section 5.3.3 "RRC connection
establishment" in 3GPP TS 36.331 V11.2.0, only UEs originating services perform access
decision after receiving AC control parameters from the eNodeB. UEs handed over from
other cells or UEs terminating services do not perform access decision.
Huawei provides the following AC control methods:
l Static AC control
After AC control parameters are configured on the Operating Support System (OSS) by
operators, the eNodeB broadcasts parameters to UEs through system information (SI),
without considering the current network load.
l Intelligent AC control
The eNodeB determines whether to adjust and deliver AC control parameters for mobile
originated data (MO data) and mobile originated signaling (MO signaling) in a cell based
on the cell congestion state.
l Dynamic service specific access control (SSAC)
The eNodeB determines whether to adjust and deliver AC control parameters for
multimedia telephony voice and video in a cell based on cell disaster and congestionstates.
2.2 Benefits
Different AC control methods offer different benefits:
l Static AC control
Static AC control uses operator-configured parameters to ensure smooth UE access and
relieve cell congestion when a large number of UEs simultaneously access a network.
l Intelligent AC control
Compared with static AC control, intelligent AC control offers the following benefits:
eRAN
Access Class Control Feature Parameter Description 2 Overview
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 11/90
– Controls UE access for MO data or signaling to prevent a sharp increase in
signaling load.
– Performs AC control based on the cell congestion state without manual
intervention.
l Dynamic SSAC
Compared with static AC control, dynamic SSAC offers the following benefits:
– Controls the access of UEs originating multimedia telephony voice or video to
prevent network congestion and ensure that UEs originating data services can
timely access the disaster bulletin information on the network.
– Performs AC control based on the disaster state and cell congestion state without
manual intervention.
2.3 Architecture
Static AC Control
Figure 2-1 shows the network architecture for static AC control.
Figure 2-1 Network architecture for static AC control
1. AC control parameters configured on the OSS are sent to the eNodeB.
2. The eNodeB broadcasts the parameters using SIB2 to UEs.
3. The UEs determine whether to initiate access to this cell.
Intelligent AC Control
Figure 2-2 shows the network architecture for intelligent AC control.
Figure 2-2 Network architecture for intelligent AC control
1. AC control parameters configured on the OSS are sent to the eNodeB.
2. The eNodeB determines whether to trigger AC control based on the cell congestion state.
3. The eNodeB broadcasts the parameters using SIB2 to UEs if trigger conditions are met.
eRAN
Access Class Control Feature Parameter Description 2 Overview
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 12/90
4. The eNodeB periodically checks whether cell congestion is relieved. If no, it adjusts
access probability factors to expand the control range until the cell congestion is
relieved.
5. The eNodeB broadcasts the adjusted parameters using SIB2 to the UEs.
6. The UEs determine whether to initiate access to this cell.
Dynamic SSAC
Figure 2-3 shows the network architecture for dynamic SSAC.
Figure 2-3 Network architecture for dynamic SSAC
1. AC control parameters configured on the OSS are sent to the eNodeB.
2. The eNodeB determines whether to trigger dynamic SSAC based on the cell disaster and
congestion states.
3. The eNodeB broadcasts the parameters using SIB2 to UEs if trigger conditions are met.
4. The eNodeB periodically checks whether the cell congestion is relieved or the disaster
state is ended. If no, it adjusts access probability factors to expand the control range or
maintains the access probability factors until the cell congestion is relieved or the
disaster state is ended.
5. The eNodeB broadcasts the adjusted parameters to the UEs until the cell congestion is
relieved or the disaster state is ended.
6. The UEs determine whether to initiate access to this cell.
eRAN
Access Class Control Feature Parameter Description 2 Overview
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 13/90
3 Technical Description
3.1 Related Concepts
Access Types
SIB2 can contain the following access types in the ac-BarringInfo IE:
l Emergency call
l MO data
l MO signaling
l Multimedia telephony voicel Multimedia telephony video
l CS fallback (CSFB)
When a UE switches from idle mode to connected mode, it sends an RRC Connection
Request message to the eNodeB. The UE determines whether its access is allowed based on
access barring information broadcast in system information and the cause of RRC connection
setup or the cause of UE access. The CellAcBar. AcBarringInfoCfgInd parameter specifies
whether access barring information is broadcast.
NOTE
When selecting a cell to camp on, a UE does not consider access barring information, which means thata UE of a specific AC can camp on a cell even if this AC is barred. In addition, the UE does not perform
cell reselection when the indicated access barring information changes.
AC Control Parameters
For emergency calls, the ac-BarringForEmergency parameter is defined to specify whether to
prohibit emergency calls from accessing a cell.
For other access types, the following parameters are defined in 3GPP specifications:
l ac-BarringFactor
A random number (rand ) is generated by a UE after it initiates an access request. If thevalue of rand is less than that of ac-BarringFactor, the UE proceeds with the access
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 14/90
procedure. If the value of rand is greater than or equal to that of ac-BarringFactor, the
UE stops the access procedure.
l ac-BarringTime
Together with rand , this parameter determines the duration for barring this access
request as follows:
Access barring duration = (0.7 + 0.6 x rand ) x ac-BarringTime
After the duration ends, the UE generates a rand and compares it with ac-BarringFactor
again.
l ac-BarringForSpecialAC
This parameter determines whether UEs of AC 11 to AC 15 can access a cell.
According to 3GPP specifications, ac-BarringFactor can be set only to P00(0%) when any of
the bits of ac-BarringForSpecialAC is set to 1. For details, see section 6.3.1 "System
information blocks" in 3GPP TS 36.331 V11.2.0.
AC Control Methods
Huawei provides the following AC control methods:
l Static AC control
l Intelligent AC control
l Dynamic SSAC
Table 3-1 describes the access types, control policies, and application scenarios of the AC
control methods.
Table 3-1 Access types, control policies, and application scenarios of the AC control methods
Category Access Type Control Policy Application Scenarios
3.2 Static AC
Control
l Emergency
call
l MO data
l MO signaling
l Multimedia
telephony
voice
l Multimedia
telephonyvideo
l CSFB
The eNodeB
broadcasts AC
control parameters
to UEs, without
considering the
current network
load.
A large number of UEs
simultaneously access the
network.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 15/90
Category Access Type Control Policy Application Scenarios
3.3 Intelligent
AC Control
l MO data
l MO signaling
The eNodeB
determines
whether to adjust
and send AC
control parameters
in a cell based on
the cell congestion
state.
Application scenarios:
l A large number of UEs
simultaneously access thenetwork.
l If intelligent AC control is
enabled in a congested cell,
new UEs may not be able
to access the network. If
this impact is acceptable,
intelligent AC control can
be enabled permanently to
relieve cell congestion,
even unpredictable
congestion.
3.4 Dynamic
SSAC
l Multimedia
telephony
voice
l Multimedia
telephony
video
The eNodeB
determines
whether to adjust
and send AC
control parameters
in a cell based on
the cell disaster
and congestion
states.
Application scenarios:
l A large number of UEs
simultaneously access the
network. It is recommended
that this method be used for
disasters such as
earthquakes and tsunamis.
l A large number of UEs
simultaneously originate
multimedia telephony voice
or video.
3.2 Static AC Control
3.2.1 Static AC Control Procedure
When the CellAlgoSwitch. AcBarAlgoSwitch parameter is set to
ACBAR_SWITCH_STATIC, static AC control is enabled.
NOTE
When the CellAlgoSwitch. AcBarAlgoSwitch parameter is set to
ACBAR_SWITCH_DISABLE(Disable), AC control is disabled.
Figure 3-1 shows the static AC control procedure, involving all access types.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 16/90
Figure 3-1 Static AC control procedure
NOTE
For emergency call, MO signaling, MO data, and CSFB, the UE checks in the access stratum whether to
initiate cell access.
For multimedia telephony voice and video, the UE checks in the non-access stratum whether to initiate
cell access. If the check is passed and the AC control parameters for MO data are available, the UE then
checks again in the access stratum whether to initiate cell access.
AC barring for different access types is controlled by the following parameters in the
CellAcBar MO:
l CellAcBar. AcBarringForEmergency for emergency calls (AC 10)
l CellAcBar. AcBarringForMoDataCfgInd for MO data
l CellAcBar. AcBarringForMoSigCfgInd for MO signaling
l CellAcBar. AcBarForMVoiceCfgInd for multimedia telephony voice
l CellAcBar. AcBarForMVideoCfgInd for multimedia telephony video
l CellAcBar. AcBarForCsfbCfgInd for CSFB
The UE determines whether its access is barred based on the AC control parameters received
from the eNodeB. For details, see 3.2.2 Access Decision Procedure.
NOTE
For details about the list of barred ACs and how a UE determines its AC, see chapter 4 "Access control"
in 3GPP TS 22.011 V10.0.0 and section 3.4 "Access control" in 3GPP TS 23.122 V10.0.0.
3.2.2 Access Decision Procedure
This section describes the access decision procedures that UEs perform after receiving ACcontrol parameters from the eNodeB.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 17/90
Emergency Calls
Figure 3-2 shows the access decision procedure for emergency calls.
Figure 3-2 Access decision procedure for emergency calls
MO Data
Figure 3-3 shows the access decision procedure for MO data.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
12
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 18/90
Figure 3-3 Access decision procedure for MO data
The access barring timer for MO data is started by the originating UE. The timer length is
calculated based on the value of the CellAcBar. AcBarTimeForCall parameter. For details,
see section 5.3.3.11 "Access barring check" in 3GPP TS 36.331 V11.2.0.
The AC control for MO data is specified by the following parameters:
l CellAcBar. AcBarringFactorForCall : specifies the access probability factor for MO
data.
l CellAcBar. AcBarTimeForCall : specifies the access barring duration for MO data.
l CellAcBar. AC11BarforCall : specifies the access barring indicator for MO data on UEs
of AC 11.
l CellAcBar. AC12BarforCall : specifies the access barring indicator for MO data on UEs
of AC 12.
l CellAcBar. AC13BarforCall : specifies the access barring indicator for MO data on UEs
of AC 13.
l
CellAcBar. AC14BarforCall : specifies the access barring indicator for MO data on UEsof AC 14.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
13
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 19/90
l CellAcBar. AC15BarforCall : specifies the access barring indicator for MO data on UEs
of AC 15.
The CellAcBar. AcBarringFactorForCall parameter can be set only to P00(0%) when any of
the parameters CellAcBar. AC11BarforCall to CellAcBar. AC15BarforCall is set to
BOOLEAN_TRUE(true).
MO Signaling
Figure 3-4 shows the access decision procedure for MO signaling.
Figure 3-4 Access decision procedure for MO signaling
The access barring timer for MO signaling is started by the originating UE. The timer length
is calculated based on the value of the CellAcBar. AcBarTimeForSig parameter. For details,
see section 5.3.3.11 "Access barring check" in 3GPP TS 36.331 V11.2.0.
The AC control for MO signaling is specified by the following parameters:
l
CellAcBar. AcBarringFactorForSig : specifies the access probability factor for MOsignaling.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
14
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 20/90
l CellAcBar. AcBarTimeForSig : specifies the access barring duration for MO signaling.
l CellAcBar. AC11BarForSig : specifies the access barring indicator for MO signaling on
UEs of AC 11.
l CellAcBar. AC12BarForSig : specifies the access barring indicator for MO signaling on
UEs of AC 12.
l CellAcBar. AC13BarForSig : specifies the access barring indicator for MO signaling on
UEs of AC 13.
l CellAcBar. AC14BarForSig : specifies the access barring indicator for MO signaling on
UEs of AC 14.
l CellAcBar. AC15BarForSig : specifies the access barring indicator for MO signaling on
UEs of AC 15.
The CellAcBar. AcBarringFactorForSig parameter can be set only to P00(0%) when any of
the parameters CellAcBar. AC11BarForSig to CellAcBar. AC15BarForSig is set to
BOOLEAN_TRUE(true).
Multimedia Telephony Voice
Figure 3-5 shows the access decision procedure for multimedia telephony voice.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
15
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 21/90
Figure 3-5 Access decision procedure for multimedia telephony voice
The access barring timer for multimedia telephony voice is started by the originating UE. The
timer length is calculated based on the value of the CellAcBar. AcBarTimeForMVoice
parameter. For details, see section 5.3.3.11 "Access barring check" in 3GPP TS 36.331
V11.2.0.
The AC control for multimedia telephony voice is specified by the following parameters:
l CellAcBar. AcBarFactorForMVoice: specifies the access probability factor for
multimedia telephony voice.
l CellAcBar. AcBarTimeForMVoice: specifies the access barring duration for multimedia
telephony voice.
l CellAcBar. SpecialACBarForMVoice: specifies the access barring indicators for
multimedia telephony voice on UEs of ACs 11 to 15.
The access barring indicators for multimedia telephony voice on UEs of ACs 11 to 15 are
specified by the bits of the CellAcBar. SpecialACBarForMVoice parameter.
The CellAcBar. AcBarFactorForMVoice parameter can be set only to P00(0%) when anyoption under the CellAcBar. SpecialACBarForMVoice parameter is selected.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
16
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 22/90
Multimedia Telephony Video
Figure 3-6 shows the access decision procedure for multimedia telephony video.
Figure 3-6 Access decision procedure for multimedia telephony video
The access barring timer for multimedia telephony video is started by the originating UE. The
timer length is calculated based on the value of the CellAcBar. AcBarTimeForMVideo
parameter. For details, see section 5.3.3.11 "Access barring check" in 3GPP TS 36.331
V11.2.0.
The AC control for multimedia telephony video is specified by the following parameters:
l CellAcBar. AcBarFactorForMVideo: specifies the access probability factor for
multimedia telephony video.
l CellAcBar. AcBarTimeForMVideo: specifies the access barring duration for multimedia
telephony video.
l CellAcBar. SpecialACBarForMVideo: specifies the access barring indicators for
multimedia telephony video on UEs of ACs 11 to 15.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
17
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 23/90
The access barring indicators for multimedia telephony video on UEs of ACs 11 to 15 are
specified by the bits of the CellAcBar. SpecialACBarForMVideo parameter.
The CellAcBar. AcBarFactorForMVideo parameter can be set only to P00(0%) when any
option under the CellAcBar. SpecialACBarForMVideo parameter is selected.
CSFB
The UE uses the following rules to make access decisions on CSFB:
l If AC control parameters from the eNodeB contain CSFB-related parameters, these
parameters are used.
l If AC control parameters from the eNodeB do not contain CSFB-related parameters, AC
control parameters for MO data are used.
Figure 3-7 shows the access decision procedure for CSFB.
Figure 3-7 Access decision procedure for CSFB
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
18
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 24/90
The access barring timer for CSFB is started by the UE initiating the CSFB. The timer length
is calculated based on the value of the CellAcBar. AcBarTimeForCsfb parameter. For details,
see section 5.3.3.11 "Access barring check" in 3GPP TS 36.331 V11.2.0.
The AC control for CSFB is specified by the following parameters:
l CellAcBar. AcBarFactorForCsfb: specifies the access probability factor for CSFB.
l CellAcBar. AcBarTimeForCsfb: specifies the access barring duration for CSFB.
l CellAcBar. SpecialACBarForCsfb: specifies the access barring indicators for CSFB on
UEs of ACs 11 to 15.
The access barring indicators for CSFB on UEs of ACs 11 to 15 are specified by the bits of
the CellAcBar. SpecialACBarForCsfb parameter.
The CellAcBar. AcBarFactorForCsfb parameter can be set only to P00(0%) when any
option under the CellAcBar. SpecialACBarForCsfb parameter is selected.
If access to an E-UTRAN cell is barred, the UE selects a GERAN or UTRAN cell through the
cell reselection procedure to ensure improved user experience. For details, see section 5.6.1.6
"Abnormal cases in the UE" in 3GPP TS 24.301 V10.0.0.
3.3 Intelligent AC Control
3.3.1 Intelligent AC Control Procedure
Intelligent AC control is enabled when the following conditions are met:
l The CellAlgoSwitch. AcBarAlgoSwitch parameter is set to
ACBAR_SWITCH_DYNAMIC(dynamic configuration).
l The DYNAMIC_FOR_MO(DYNAMIC_FOR_MO) option of the
CellAlgoSwitch. AcBarAlgoforDynSwitch parameter is selected.
Under these parameter settings, intelligent AC control is applied to MO data and MO
signaling, and static AC control (if configured) is applied to other access types.
Figure 3-8 shows the intelligent AC control procedure.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
19
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 25/90
Figure 3-8 Intelligent AC control procedure
3.3.2 Implementation Principles
Cell Congestion Checking
After intelligent AC control is enabled, the eNodeB periodically checks the cell state based on
the CellDynAcBarAlgoPara. DynAcBarStatPeriod parameter.
Table 3-2 describes the congestion trigger and congestion relief conditions based on the
EnodebFlowCtrlPara. DynAcBarPolicyMode parameter.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
20
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 26/90
Table 3-2 Congestion trigger and congestion relief conditions
Value ofEnodebFlowCtrlPara. DynAcBarPolicyMo
de
Congestion TriggerCondition
Congestion ReliefCondition
FLOWCONTROL The ratio of the flow control
duration to the measurement
duration is greater than or
equal to the value of
CellDynAcBarAlgo-
Para. DynAcBarTriggerThd .
The ratio of the flow control
duration to the measurement
duration is less than or equal
to the value of
CellDynAcBarAlgo-
Para. DynAcBarCancelThd .
CPULOAD The proportion of CPU
overload time is greater than or
equal to the value of
CellDynAcBarAlgo-Para. DynAcBarTriggerThd .
The CPU overload time is the
time during which the CPU
usage of the main control
board or baseband processing
unit for a cell is greater than or
equal to the value of
EnodebFlowCtrlPara.CpuLo
adThd .
The proportion of CPU
overload time is less than or
equal to the value of
CellDynAcBarAlgo-Para. DynAcBarCancelThd .
The CPU overload time is the
time during which the CPU
usage of the main control
board or baseband processing
unit for a cell is greater than or
equal to the value of
EnodebFlowCtrlPara.CpuLo
adThd .
NOTE
For details about flow control, see Flow Control Feature Parameter Description.
For macro eNodeBs, flow control is triggered by a large amount of RRC signaling or RACH signaling.
The cells on the same board have the same flow control state because flow control is performed at the
board level. If the CellDynAcBarAlgoPara. DynAcBarTriggerThd parameter is set to the same value
for the cells on a board, the congestion states of the cells are the same. It is recommended that the same
AC control parameters be configured for cells on the same board. For micro eNodeBs, flow control is
triggered only by a large amount of RACH signaling.
If the EnodebFlowCtrlPara. DynAcBarPolicyMode parameter is modified during the
measurement period specified by the CellDynAcBarAlgoPara. DynAcBarStatPeriod
parameter, the eNodeB checks whether the cell is congested based on the cell statesdetermined using both policies.
For example, the measurement period is 20s, the flow control policy is used in the first 10s,
and the CPU usage policy is used in the second 10s. 20 cell states are obtained in the
measurement period. The first 10 states are obtained when the flow control policy is used, and
the second 10 states are obtained when the CPU usage policy is used. Based on the 20 cell
states, the eNodeB calculates the proportion of time during which the cell is in the congestion
state to determine whether the cell is congested during the measurement period.
Triggering of Intelligent AC Control
After intelligent AC control is enabled, the eNodeB periodically checks whether a cell iscongested and counts the number of consecutive periods during which the cell is congested.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
21
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 27/90
If the number of consecutive periods during which the cell is congested reaches the value of
the CellDynAcBarAlgoPara. MoTriggerCondSatiPeriods parameter, the eNodeB triggers
intelligent AC control. The eNodeB sends AC control parameters using SIB2 to dynamically
adjust the access probability factor CellAcBar. AcBarringFactorForSig or
CellAcBar. AcBarringFactorForCall .
Handling After Intelligent AC Control Is Triggered
If intelligent AC control triggered in the last period is not canceled in the current period, the
eNodeB checks whether the cell is congested in the current period.
l If the cell is congested, AC control cannot be canceled, and the eNodeB gradually
decreases the access probability factor value to increase the proportion of barred UEs.
The access barring duration is not adjusted.
l If the cell congestion is relieved, then:
– If the number of consecutive periods during which the cell congestion is relieved is
less than the value of the CellDynAcBarAlgoPara. MoCancelCondSatiPeriods parameter, the eNodeB maintains the broadcast access probability factor for MO
data or MO signaling.
– If the number of consecutive periods during which the cell congestion is relieved
reaches the value of the CellDynAcBarAlgoPara. MoCancelCondSatiPeriods
parameter, the eNodeB sends SIB2 that does not contain AC control configurations
for MO data or MO signaling to UEs to cancel AC control on MO signaling or MO
data. AC control on other access types is not canceled.
NOTE
The value of the CellDynAcBarAlgoPara. DynAcBarCancelThd parameter must be less than the value
of the CellDynAcBarAlgoPara. DynAcBarTriggerThd parameter.
Access Probability Factor Adjustment
Access probability factors are defined in section 6.3.1 "System information blocks" in 3GPP
TS 36.331 V11.2.0. After intelligent AC control is enabled, the access probability factors are
selected in descending order until cell congestion is relieved. The AC barring duration is the
same as the duration configured for static AC control. Figure 3-9 shows the detailed access
probability factor adjustment procedure.
Figure 3-9 Detailed access probability factor adjustment procedure
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
22
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 28/90
To ensure that some UEs can access the cell, the minimum access probability factor is
P05(5%). If cell congestion is not immediately relieved even with an access probability factor
of P05(5%), then P05(5%) is retained until cell congestion is eventually relieved.
If the cell is congested again, the access probability factor is selected in descending order
from P95(95%) again.
3.4 Dynamic SSAC
3.4.1 Dynamic SSAC Procedure
Dynamic SSAC is enabled when the following conditions are met:
l The CellAlgoSwitch. AcBarAlgoSwitch parameter is set to
ACBAR_SWITCH_DYNAMIC(dynamic configuration).
l The DYNAMIC_FOR_SSAC(DYNAMIC_FOR_SSAC) option of theCellAlgoSwitch. AcBarAlgoforDynSwitch parameter is selected.
Under these parameter settings, dynamic SSAC is applied to multimedia telephony voice and
video, and static AC control (if configured) is applied to other access types.
Figure 3-10 shows the dynamic SSAC procedure.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
23
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 29/90
Figure 3-10 Dynamic SSAC Procedure
3.4.2 Implementation Principles
Cell Disaster and Congestion Checking
After dynamic SSAC is enabled, the eNodeB periodically checks whether a cell is in a
disaster or congestion state based on the CellDynAcBarAlgoPara. DynAcBarStatPeriod
parameter.
l Disaster state
– The cell enters a disaster state when it receives an earthquake and tsunami warning
system (ETWS) primary notification (PN) or commercial mobile alert system
(CMAS) message configured by theCellDynAcBarAlgoPara. DisasterReferenceInd parameter for the cell.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
24
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 30/90
– The disaster state duration is specified by the
CellDynAcBarAlgoPara. DisasterDuration parameter. The cell exits the disaster
state when this duration ends.
NOTE
The duration specified by the CellDynAcBarAlgoPara. DisasterDuration parameter isindependent of the value of the CellDynAcBarAlgoPara. DisasterReferenceInd parameter.
The duration starts when the cell receives a disaster notification message.
l Congestion state
The methods for determining whether a cell is in a congestion state are the same as those
for intelligent AC control. For details, see Cell Congestion Checking in 3.3.2
Implementation Principles.
Triggering of SSAC
After dynamic SSAC is enabled, the eNodeB periodically checks whether a cell is in a
congestion or disaster state and counts the number of consecutive periods during which the
cell is in a congestion or disaster state.
When the number of consecutive periods during which a cell is in a congestion or disaster
state reaches the value of CellDynAcBarAlgoPara. SsacTriggerCondSatiPeriods, the
eNodeB triggers dynamic SSAC for the cell. The eNodeB sends AC control parameters using
SIB2 to dynamically adjust the access probability factor CellAcBar. AcBarFactorForMVoice
or CellAcBar. AcBarFactorForMVideo.
Handling After Dynamic SSAC Is Triggered
If dynamic SSAC triggered in the last period is not canceled in the current period, the eNodeB
checks whether the cell is in a congestion or disaster state in the current period.
l If the cell is in congestion and disaster states at the same time, AC control cannot be
canceled and the eNodeB gradually decreases the access probability factor value for the
cell to increase the proportion of barred UEs. The access barring duration is not adjusted.
l If the cell is not in congestion and disaster states at the same time, then:
– If the number of consecutive periods during which the cell is out of the congestion
or disaster state does not reach the value of the
CellDynAcBarAlgoPara. SsacCancelCondSatiPeriods parameter, the eNodeB
maintains the broadcast access probability factor for multimedia telephony voice or
video.
– If the number of consecutive periods during which the cell is out of the congestion
or disaster state reaches the value of theCellDynAcBarAlgoPara. SsacCancelCondSatiPeriods parameter, the eNodeB
broadcasts SIB2 that does not contain AC control parameters for multimedia
telephony voice or video to cancel AC control on multimedia telephony voice or
video.
NOTE
The value of the CellDynAcBarAlgoPara. DynAcBarCancelThd parameter must be less than the value
of the CellDynAcBarAlgoPara. DynAcBarTrigg erThd parameter.
Access Probability Factor Adjustment
After dynamic SSAC is started, the eNodeB adjusts the access probability factors until thecell congestion is relieved or the cell disaster state is ended. The adjustment mechanism is the
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
25
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 31/90
same as that described in Access Probability Factor Adjustment in 3.3.2 Implementation
Principles.
eRAN
Access Class Control Feature Parameter Description 3 Technical Description
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
26
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 32/90
4 Related Features
4.1 Features Related to LOFD-070207 Intelligent AccessClass Control
Prerequisite Features
The prerequisite feature is LBFD-002009 Broadcast of system information because the
eNodeB broadcasts AC control parameters using SIB2.
Mutually Exclusive Features None
Impacted Features
None
4.2 Features Related to LOFD-008002 Dynamic Service-specific Access Control
Prerequisite Features
Dynamic SSAC depends on the feature LBFD-002009 Broadcast of system information
because AC control parameters are broadcast through SIB2 messages.
Dynamic SSAC depends on the feature LBFD-002029 Earthquake and Tsunami Warning
System (ETWS) when the CellDynAcBarAlgoPara. DisasterReferenceInd parameter is set
to ETWS_PN(ETWS_PN) or ETWS_PN_TEST(ETWS_PN_TEST).
Dynamic SSAC depends on the feature LOFD-001092 CMAS Support when the
CellDynAcBarAlgoPara. DisasterReferenceInd parameter is set to CMAS(CMAS).
eRAN
Access Class Control Feature Parameter Description 4 Related Features
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
27
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 33/90
Mutually Exclusive Features
None
Impacted Features None
eRAN
Access Class Control Feature Parameter Description 4 Related Features
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
28
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 34/90
5 Network Impact
5.1 LOFD-070207 Intelligent Access Class Control
System Capacity
When the EnodebFlowCtrlPara. DynAcBarPolicyMode parameter is set to
CPULOAD(CPULOAD) and the EnodebFlowCtrlPara.CpuLoadThd parameter is set to a
value less than 80% (for example, 50%), the access of a large number of UEs is barred
although the CPU resource is sufficient. In this case, user experience is affected and the
specified busy hour call attempts (BHCA) may fail to be reached.
Network Performance
The highest frequency for access probability factor adjustment is once every 20 seconds
during intelligent AC control. This has no influence on network performance.
If the RRC connection setup success rate decreases because of flow control on the main
control board or baseband processing units, intelligent AC control prevents some UEs from
accessing the cell. The cell congestion will be relieved, and the RRC connection setup success
rate will also increase. The degree of the increase depends on the cell congestion level, AC
control parameter settings, and the proportion of UEs that support AC control in the network.
If UEs are barred, their access experience will be affected.
5.2 LOFD-008002 Dynamic Service-specific Access Control
System Capacity
The impact of this feature on system capacity is the same as that of LOFD-070207 Intelligent
Access Class Control.
Network Performance
The impact of this feature on network performance is the same as that of LOFD-070207Intelligent Access Class Control.
eRAN
Access Class Control Feature Parameter Description 5 Network Impact
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
29
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 35/90
6 Engineering Guidelines
6.1 Static AC control
6.1.1 When to Use Static AC Control
Static AC control can be used only when a large number of UEs will simultaneously access
the network.
6.1.2 Required Information
Collect the following information before feature deployment:
l Whether UEs support AC control
Operators can obtain the distribution of various categories of UEs and the capability of
these UEs to support AC control from EPC information. Only UEs that support AC
control defined in 3GPP Release 8 and later can support this feature.
l Whether heavy traffic causes signaling shock to a network when a large number of UEs
in a cell simultaneously access the network
6.1.3 Planning
6.1.3.1 RF Planning N/A
6.1.3.2 Network Planning
N/A
6.1.3.3 Hardware Planning
N/A
6.1.4 Deployment
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
30
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 36/90
6.1.4.1 Requirements
Other NEs
l Emergency calls, MO data, and MO signaling require that UEs support the AC control
mechanism defined in 3GPP Release 8.
l Multimedia telephony voice and multimedia telephony video require that UEs support
the AC control mechanism defined in 3GPP Release 9.
l CSFB requires that UEs support the AC control mechanism defined in 3GPP Release 10.
License
None
6.1.4.2 Data Preparation
This section describes the data that you need to collect for setting parameters. Required data is
data that you must collect for all scenarios. Collect scenario-specific data when necessary for
a specific feature deployment scenario.
There are three types of data sources:
l Network plan (negotiation not required): parameter values planned and set by the
operator
l Network plan (negotiation required): parameter values planned by the operator and
negotiated with the evolved packet core (EPC) or peer transmission equipment
l User-defined: parameter values set by users
Table 6-1 Parameters that must be set in the CellAlgoSwitch MO to set the AC control switch
Parameter Name
Parameter ID DataSource
Setting Notes
Local cell
ID
CellAlgoSwitc
h. LocalCellId
Network
plan
(negotiation
not required)
This parameter specifies the local ID of a
cell. It uniquely identifies a cell within the
coverage of an eNodeB.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
31
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 37/90
Parameter Name
Parameter ID DataSource
Setting Notes
AcBar
algorithms
switch
CellAlgoSwitc
h. AcBarAlgoS
witch
Network
plan
(negotiation
not required)
This parameter specifies an AC control
algorithm.
When this parameter is set to
ACBAR_SWITCH_DYNAMIC(dynamic
configuration), dynamic AC control is
enabled. The
CellAlgoSwitch. AcBarAlgoforDynSwitch
parameter determines whether to enable
intelligent AC control on MO signaling and
MO data or enable dynamic SSAC on
multimedia telephony voice and multimedia
telephony video.
When this parameter is set to
ACBAR_SWITCH_STATIC(static
configuration), static AC control is enabled.
In this situation, the access probability
factors and average access barring duration
are set in the CellAcBar MO.
When this parameter is set to
ACBAR_SWITCH_DISABLE(Disable) ,
AC barring is disabled.
Ac Bar
Algorithm
Switch for
Dynamic
CellAlgoSwitc
h. AcBarAlgof
orDynSwitch
Network
plan
(negotiation
not required)
This parameter determines whether to enable
intelligent AC control on MO signaling and
MO data or SSAC on multimedia telephony
voice and video. This parameter is valid only
when CellAlgoSwitch. AcBarAlgoSwitch is
set to
ACBAR_SWITCH_DYNAMIC(dynamic
configuration).
Table 6-2 Parameters that must be set in the CellAcBar MO to AC control information
Parameter
Name
Parameter ID Data
Source
Setting Notes
Local cell ID CellAcBar. Lo
calCellId
Network
plan
(negotiation
not required)
This parameter specifies the local ID of a
cell. It uniquely identifies a cell within
the coverage of an eNodeB.
AC barring
information
configure
indicator
CellAcBar. Ac
BarringInfoCf
gInd
Network
plan
(negotiation
not required)
This parameter specifies whether to
configure AC control information.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
32
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 38/90
ParameterName
Parameter ID DataSource
Setting Notes
Emergency
call barring
state
CellAcBar. Ac
BarringForE
mergency
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 10 can initiate access for emergency
calls.
If this parameter is set to
BOOLEAN_TRUE(True), UEs of AC
0 to AC 9 or those without IMSIs cannot
initiate access for emergency calls.
If this parameter is set to
BOOLEAN_FALSE(False), such UEs
can initiate access for emergency calls.
UEs of AC N (ranging from 11 to 15)
cannot initiate access for emergency calls
if both AC N and AC 10 are barred.Otherwise, such UEs can initiate access
for emergency calls.
AC barring
for mobile
data
configure
indicator
CellAcBar. Ac
BarringForMo
DataCfgInd
Network
plan
(negotiation
not required)
This parameter specifies whether to
configure AC control information for
MO data.
Access
probability
factor for
originatingcall
CellAcBar. Ac
BarringFactor
ForCall
Network
plan
(negotiation
not required)
This parameter specifies an access
probability factor for MO data. If the
random number generated by a UE is
less than this access probability factor,the UE can initiate access for MO data.
Otherwise, the UE cannot initiate access
for MO data.
This parameter must be set to P00(0%)
if any of AC 11 to AC 15 is barred for
MO data.
Mean access
barring time
for
originating
call
CellAcBar. Ac
BarTimeForC
all
Network
plan
(negotiation
not required)
This parameter specifies the average
access barring duration for MO data.
AC11 barring
state for
originating
call
CellAcBar. AC
11BarforCall
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 11 can initiate access for MO data.
AC12
barring state
for
originating
call
CellAcBar. AC
12BarforCall
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 12 can initiate access for MO data.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
33
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 39/90
ParameterName
Parameter ID DataSource
Setting Notes
AC13
barring state
for
originating
call
CellAcBar. AC
13BarforCall
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 13 can initiate access for MO data.
AC14
barring state
for
originating
call
CellAcBar. AC
14BarforCall
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 14 can initiate access for MO data.
AC15
barring state
for originating
call
CellAcBar. AC
15BarforCall
Network
plan
(negotiationnot required)
This parameter specifies whether UEs of
AC 15 can initiate access for MO data.
AC barring
for mobile
signal
configure
indicator
CellAcBar. Ac
BarringForMo
SigCfgInd
Network
plan
(negotiation
not required)
This parameter specifies whether to
configure AC control information for
MO signaling.
Access
probability
factor for signaling
CellAcBar. Ac
BarringFactor
ForSig
Network
plan
(negotiationnot required)
This parameter specifies an access
probability factor for MO signaling. If
the random number generated by a UE isless than this access probability factor,
the UE can initiate access for MO
signaling.
Otherwise, the UE cannot initiate access
for MO signaling. This parameter must
be set to P00(0%) if any of AC 11 to AC
15 is barred for MO signaling.
Mean access
barring time
for signaling
CellAcBar. Ac
BarTimeForSi
g
Network
plan
(negotiation
not required)
This parameter specifies the average
access barring duration for MO
signaling.
AC11 barring
state for
signaling
CellAcBar. AC
11BarForSig
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 11 can initiate access for MO
signaling.
AC12
barring state
for signaling
CellAcBar. AC
12BarForSig
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 12 can initiate access for MO
signaling.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
34
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 40/90
ParameterName
Parameter ID DataSource
Setting Notes
AC13
barring state
for signaling
CellAcBar. AC
13BarForSig
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 13 can initiate access for MO
signaling.
AC14
barring state
for signaling
CellAcBar. AC
14BarForSig
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 14 can initiate access for MO
signaling.
AC15
barring state
for signaling
CellAcBar. AC
15BarForSig
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 15 can initiate access for MO
signaling.
AC barring
for MMTEL
voice
configure
indicator
CellAcBar. Ac
BarForMVoice
CfgInd
Network
plan
(negotiation
not required)
This parameter specifies whether to
configure AC control information for
multimedia telephony voice.
Access
probability
factor for
MMTEL
voice
CellAcBar. Ac
BarFactorFor
MVoice
Network
plan
(negotiation
not required)
This parameter specifies an access
probability factor for multimedia
telephony voice. If the random number
generated by a UE is less than this access
probability factor, the UE can initiate
access for multimedia telephony voice.Otherwise, the UE cannot initiate access
for multimedia telephony voice.
This parameter must be set to P00(0%)
if any of AC 11 to AC 15 is barred for
multimedia telephony voice.
Mean access
barring time
for MMTEL
voice
CellAcBar. Ac
BarTimeForM
Voice
Network
plan
(negotiation
not required)
This parameter specifies the average
access barring duration for multimedia
telephony voice.
AC 11-15 barring state
for MMTEL
voice
CellAcBar. SpecialACBarFo
rMVoice
Network plan
(negotiation
not required)
This parameter specifies whether UEs of AC 11 to AC 15 can initiate access for
multimedia telephony voice.
AC barring
for MMTEL
video
configure
indicator
CellAcBar. Ac
BarForMVide
oCfgInd
Network
plan
(negotiation
not required)
This parameter specifies whether to
configure AC control information for
multimedia telephony video.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
35
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 41/90
ParameterName
Parameter ID DataSource
Setting Notes
Access
probability
factor for
MMTEL
video
CellAcBar. Ac
BarFactorFor
MVideo
Network
plan
(negotiation
not required)
This parameter specifies an access
probability factor for multimedia
telephony video. If the random number
generated by a UE is less than this access
probability factor, the UE can initiate
access for multimedia telephony video.
Otherwise, the UE cannot initiate access
for multimedia telephony video.
This parameter must be set to P00(0%)
if any of AC 11 to AC 15 is barred for
multimedia telephony video.
Mean access
barring timefor MMTEL
video
CellAcBar. Ac
BarTimeForM Video
Network
plan(negotiation
not required)
This parameter specifies the average
access barring duration for multimediatelephony video.
AC 11-15
barring state
for MMTEL
video
CellAcBar. Sp
ecialACBarFo
rMVideo
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 11 to AC 15 can initiate access for
multimedia telephony video.
AC barring
for CSFB
configure
indicator
CellAcBar. Ac
BarForCsfbCf
gInd
Network
plan
(negotiation
not required)
This parameter specifies whether to
configure AC control information for
CSFB.
Access
probability
factor for
CSFB
CellAcBar. Ac
BarFactorFor
Csfb
Network
plan
(negotiation
not required)
This parameter specifies an access
probability factor for CSFB. If the
random number generated by a UE is
less than this access probability factor,
the UE can initiate access for CSFB.
Otherwise, the UE cannot initiate access
for CSFB.
This parameter must be set to P00(0%)
if any of AC 11 to AC 15 is barred for
CSFB.
Mean access barring time
for CSFB
CellAcBar. Ac BarTimeForCs
fb
Network plan
(negotiation
not required)
This parameter specifies the averageaccess barring duration for CSFB.
AC 11-15
barring state
for CSFB
CellAcBar. Sp
ecialACBarFo
rCsfb
Network
plan
(negotiation
not required)
This parameter specifies whether UEs of
AC 11 to AC 15 can initiate access for
CSFB.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
36
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 42/90
6.1.4.3 Activation
Using the CME to Perform Batch Configuration for Newly Deployed eNodeBs
Enter the values of the parameters listed in Table 6-3 in a summary data file, which alsocontains other data for the new eNodeBs to be deployed. Then, import the summary data file
into the Configuration Management Express (CME) for batch configuration. For detailed
instructions, see "Creating eNodeBs in Batches" in the initial configuration guide for the
eNodeB, which is available in the eNodeB product documentation.
The summary data file may be a scenario-specific file provided by the CME or a customized
file, depending on the following conditions:
l The MOs in Table 6-3 are contained in a scenario-specific summary data file. In this
situation, set the parameters in the MOs, and then verify and save the file.
l Some MOs in Table 6-3 are not contained in a scenario-specific summary data file. In
this situation, customize a summary data file to include the MOs before you can set the
parameters.
Table 6-3 Static AC control parameters
MO Sheet in theSummary DataFile
Parameter Group Remarks
CellAlgoS
witch
CellAlgoSwitch For details, see 6.1.4.2 Data
Preparation.
Customize this
MO on a
pattern-type
sheet.
CellAcBar CellAcBar For details, see 6.1.4.2 Data
Preparation.
Customize this
MO on a list-
type sheet.
Using the CME to Perform Batch Configuration for Existing eNodeBs
Batch reconfiguration using the CME is the recommended method to activate a feature on
existing eNodeBs. This method reconfigures all data, except neighbor relationships, for
multiple eNodeBs in a single procedure. The procedure is as follows:
Step 1 Customize a summary data file with the MOs and parameters listed in section "Using the
CME to Perform Batch Configuration for Newly Deployed eNodeBs." For online help, press
F1 when a CME window is active, and select Managing the CME > CME Guidelines >
LTE Application Management > eNodeB Related Operations > Customizing a Summary
Data File for Batch eNodeB Configuration.
Step 2 Choose CME > LTE Application > Export Data > Export Base Station Bulk
Configuration Data (U2000 client mode), or choose LTE Application > Export Data >
Export Base Station Bulk Configuration Data (CME client mode), to export the eNodeB
data stored on the CME into the customized summary data file.
Step 3 In the summary data file, set the parameters in the MOs according to the setting notes provided in section "Data Preparation" and close the file.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
37
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 43/90
Step 4 Choose CME > LTE Application > Import Data > Import Base Station Bulk
Configuration Data (U2000 client mode), or choose LTE Application > Import Data >
Import Base Station Bulk Configuration Data (CME client mode), to import the summary
data file into the CME, and then start the data verification.
Step 5 After data verification is complete, choose CME > Planned Area > Export IncrementalScripts (U2000 client mode), or choose Area Management > Planned Area > Export
Incremental Scripts (CME client mode), to export and activate the incremental scripts. For
detailed operations, see Managing the CME > CME Guidelines > Script File Management
> Exporting Incremental Scripts from a Planned Data Area in the CME online help.
----End
Using the CME to Perform Single Configuration
On the CME, set the parameters listed in the "Data Preparation" section for a single eNodeB.
The procedure is as follows:
Step 1 In the planned data area, click Base Station in the upper left corner of the configuration
window.
Step 2 In area 1 shown in Figure 6-1, select the eNodeB to which the MOs belong.
Figure 6-1 MO search and configuration window
Step 3 On the Search tab page in area 2, enter an MO name, for example, CELL.
Step 4 In area 3, double-click the MO in the Object Name column.
Step 5 All parameters in this MO are displayed in area 4.
Step 6 Choose CME > Planned Area > Export Incremental Scripts (U2000 client mode), or
choose Area Management > Planned Area > Export Incremental Scripts (CME client
mode), to export and activate the incremental scripts.
----End
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
38
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 44/90
Using MML Commands
Step 1 To configure static AC control, perform the following steps: Run the MOD CELLACBAR
command to set AC control parameters. The access type can be emergency calls, MO data,
MO signaling, multimedia telephony voice, multimedia telephony video, or CSFB.
Step 2 Run the MOD CELLALGOSWITCH command to set the AC control mode to static AC
control.
----End
MML Command ExamplesMOD CELLACBAR: LocalCellId=0, AcBarringInfoCfgInd=CFG,
AcBarringForMoDataCfgInd=CFG, AcBarringFactorForCall=P95, AcBarTimeForCall=
ACCESS_BARRING_TIME_S4;
MOD CELLALGOSWITCH: LocalCellId=0, AcBarAlgoSwitch= ACBAR_SWITCH_STATIC;
6.1.4.4 Activation Observation
If Uu tracing results show that delivered SIB2 contains AC control parameters, static AC
control has been activated. The activation observation procedure is as follows:
Step 1 On the U2000 client, choose Monitor > Signaling Trace > Signaling Trace Management.
Step 2 On the navigation tree of the Signaling Trace Management tab page, choose Trace Type >
LTE > Application Layer > Uu Interface Trace. The Uu Interface Trace dialog box is
displayed.
Step 3 Set task information in the displayed Uu Interface Trace dialog box and click Finish. The
Uu interface signaling tracing task is started.
Step 4 Double-click the new task in the task list on the right of the Signaling Trace Management
tab page. The task monitoring tab page is displayed.
Step 5 Run the MOD CELLACBAR command to set AC control parameters in the CellAcBar MO,
for example, for MO signaling. Then, check the monitoring window for SIB2 in
RRC_SYS_INFO. If SIB2 contains the AC control parameters, as shown in Figure 6-2, static
AC control has been activated.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
39
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 45/90
Figure 6-2 Uu tracing result (SIB2)
----End
6.1.4.5 Reconfiguration
Run the MOD CELLALGOSWITCH command to switch between static AC control,
intelligent AC control, and dynamic SSAC.
6.1.4.6 Deactivation
Using the CME to Perform Batch Configuration
Batch reconfiguration using the CME is the recommended method to deactivate a feature on
eNodeBs. This method reconfigures all data, except neighbor relationships, for multipleeNodeBs in a single procedure. The procedure for feature deactivation is similar to that for
feature activation described in Using the CME to Perform Batch Configuration for
Existing eNodeBs. In the procedure, modify parameters according to Table 6-4.
Table 6-4 Static AC control parameters
MO Sheet in theSummary Data File
ParameterGroup
Setting Notes
CellAlgoSwitch CellAlgoSwitch AcBarAlgo
Switch
ACBAR_SWITCH_DISABL
E(Disable)
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
40
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 46/90
Using the CME to Perform Single Configuration
On the CME, set parameters according to Table 6-4. For detailed instructions, see Using the
CME to Perform Single Configuration described for feature activation.
Using MML Commands
Run the MOD CELLALGOSWITCH command to deactivate static AC control.
MML Command ExamplesMOD CELLALGOSWITCH: LocalCellId=0, AcBarAlgoSwitch= ACBAR_SWITCH_DISABLE;
6.1.5 Performance Monitoring
None
6.1.6 Parameter Optimization
When a large number of UEs in a cell simultaneously access the network, the cell may be
congested (for example, the CPU usage exceeds the flow control threshold). In this case,
determine the ACs to be controlled based on the following counters:
l L.RRC.ConnReq.Att.MoData
l L.RRC.ConnReq.Att.MoSig
l L.RRC.ConnReq.Att.Emc
l L.CSFB.PrepAtt
Then, set AC control parameters for the identified ACs. These parameters will be broadcast toUEs.
If the congestion is not relieved, adjust access probability factors such as
CellAcBar. AcBarringFactorForCall to expand the AC control scope, or adjust access
barring durations such as CellAcBar. AcBarTimeForCall to control the access frequencies.
6.1.7 Troubleshooting
None
6.2 Intelligent AC control
6.2.1 When to Use Intelligent AC Control
Intelligent AC control is recommended only when a large number of UEs will simultaneously
access the network, as in the case for special events such as holidays, concerts, and sporting
events or for disasters such as earthquakes and tsunamis. The reason is that intelligent AC
control has an impact on user access experience. If UE access is barred, the perceived access
delay increases.
If intelligent AC control is enabled in a congested cell, new UEs may not be able to access the
network. However, if this impact is acceptable, intelligent AC control can be enabled permanently to relieve cell congestion, even unpredictable congestion.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
41
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 47/90
6.2.2 Required Information
For details, see 6.1.2 Required Information.
6.2.3 Planning
6.2.3.1 RF Planning
N/A
6.2.3.2 Network Planning
N/A
6.2.3.3 Hardware Planning
N/A
6.2.4 Deployment
6.2.4.1 Requirements
Other NEs
UEs must support the AC control mechanism defined in 3GPP Release 8.
License
The operator has purchased and activated the license for the feature listed in the following
table.
Feature ID FeatureName
Model License ControlItem
NE SalesUnit
LOFD-07020
7
Intelligent
Access ClassControl
LT1S00I
ACC00
Intelligent Access
Class Control(FDD)
eNodeB per cell
6.2.4.2 Data Preparation
This section describes the data that you need to collect for setting parameters. Required data is
data that you must collect for all scenarios. Collect scenario-specific data when necessary for
a specific feature deployment scenario.
l For required data, see Table 6-1 and Table 6-2 in 6.1.4.2 Data Preparation.
l For scenario-specific data, see Table 6-5 and Table 6-6.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
42
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 48/90
Table 6-5 Parameters that must be set in the CellDynAcBarAlgoPara MO to configure
intelligent AC control parameters
ParameterName
Parameter ID Data Source Setting Notes
Local Cell ID CellDynAcBar
AlgoPara. Local
CellId
Network plan
(negotiation
not required)
This parameter specifies the local ID
of a cell. It uniquely identifies a cell
within the coverage of an eNodeB.
Dynamic AC
Barring
Control
Statistic
Period
CellDynAcBar
AlgoPara. Dyn
AcBarStatPerio
d
Network plan
(negotiation
not required)
This parameter specifies a period for
measuring the proportion of cell
congestion duration.
Dynamic AC
Barring
Control
Trigger
Threshold
CellDynAcBar
AlgoPara. Dyn
AcBarTriggerT
hd
Network plan
(negotiation
not required)
This parameter specifies the threshold
for triggering dynamic AC barring in a
cell. This threshold is denoted by the
proportion of time that the cell is in the
congestion state. If the actual cell
congestion duration in a statistic
period (CellDynAcBarAlgo-
Para. DynAcBarStatPeriod ) is greater
than or equal to this threshold, the
condition for triggering dynamic AC
barring is met.
Dynamic AC
Barring
ControlCancel
Threshold
CellDynAcBar
AlgoPara. Dyn
AcBarCancelT
hd
Network plan
(negotiation
not required)
This parameter specifies the threshold
for canceling dynamic AC barring in a
cell. This threshold is denoted by the proportion of time that the cell is in the
congestion state. If the actual cell
congestion duration in a statistic
period (CellDynAcBarAlgo-
Para. DynAcBarStatPeriod ) is less
than or equal to this threshold, the
condition for canceling dynamic AC
control is met.
MO Trigger
Condition
SatisfiedPeriods
CellDynAcBar
AlgoPara. MoTr
iggerCondSatiP eriods
Network plan
(negotiation
not required)
This parameter specifies a threshold
number of consecutive periods during
which the condition for triggeringintelligent AC control on MO data or
MO signaling is met.
Intelligent AC control on MO data or
MO signaling is triggered only when
the number of consecutive periods
during which the condition for
triggering intelligent AC control on
MO data or MO signaling is met
reaches the value of this parameter.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
43
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 49/90
ParameterName
Parameter ID Data Source Setting Notes
MO Cancel
Condition
Satisfied
Periods
CellDynAcBar
AlgoPara. MoC
ancelCondSatiP
eriods
Network plan
(negotiation
not required)
This parameter specifies a threshold
number of consecutive periods during
which the condition for canceling
intelligent AC control on MO data or
MO signaling is met.
Intelligent AC control on MO data or
MO signaling is canceled only when
the number of consecutive periods
during which the condition for
canceling intelligent AC control on
MO data or MO signaling is met
reaches the value of this parameter.
Table 6-6 Parameters that must be set in the EnodebFlowCtrlPara MO to configure
congestion decision policies used in intelligent AC control
ParameterName
Parameter ID Data Source Setting Notes
Dynamic AC
Barring
Policy Mode
EnodebFlowCt
rlPara. DynAcB
arPolicyMode
Network plan
(negotiation
not required)
This parameter specifies the policy of
determining cell congestion for
intelligent AC control or dynamic
SSAC.
l When this parameter is set toFLOWCONTROL(FLOWCONT
ROL), the eNodeB determines that
a cell is congested when the cell is
under flow control.
l When this parameter is set to
CPULOAD(CPULOAD), the
eNodeB determines whether a cell
is congested based on the
configured CPU load threshold. If
the CPU load of a cell's main
control board or baseband processing unit is greater than or
equal to the configured CPU load
threshold, the cell is congested. The
CPU load threshold is specified by
the
EnodebFlowCtrlPara .CpuLoadT
hd parameter.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
44
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 50/90
ParameterName
Parameter ID Data Source Setting Notes
CPU Load
Threshold
EnodebFlowCt
rlPara.CpuLoa
dThd
Network plan
(negotiation
not required)
This parameter specifies the CPU load
threshold for determining whether a
cell is congested. This parameter takes
effect only when
EnodebFlowCtrlPara. DynAcBarPoli
cyMode is set to
CPULOAD(CPULOAD). If the CPU
load of a cell's main control board or
baseband processing unit is greater
than or equal to this parameter value,
the cell is congested. If the CPU load
is less than this parameter value, the
cell is not congested.
6.2.4.3 Activation
Using the CME to Perform Batch Configuration for Newly Deployed eNodeBs
Enter the values of the parameters listed in Table 6-7 in a summary data file, which also
contains other data for the new eNodeBs to be deployed. Then, import the summary data file
into the CME for batch configuration. For detailed instructions, see "Creating eNodeBs in
Batches" in the initial configur ation guide for the eNodeB, which is available in the eNodeB
product documentation.
The summary data file may be a scenario-specific file provided by the CME or a customized
file, depending on the following conditions:
l The MOs in Table 6-7 are contained in a scenario-specific summary data file. In this
situation, set the parameters in the MOs, and then verify and save the file.
l Some MOs in Table 6-7 are not contained in a scenario-specific summary data file. In
this situation, customize a summary data file to include the MOs before you can set the
parameters.
Table 6-7 Intelligent AC control parameters
MO Sheet in theSummaryData File
Parameter Group Remarks
CellAcBar CellAcBar For details, see 6.1.4.2 Data
Preparation.
Customize this
MO on a
pattern-type
sheet.
CellAlgoSwitc
h
CellAlgoSwitc
h
For details, see 6.1.4.2 Data
Preparation.
Customize this
MO on a
pattern-type
sheet.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
45
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 51/90
MO Sheet in theSummaryData File
Parameter Group Remarks
CellDynAcBar
AlgoPara
CellDynAcBar
AlgoPara
For details, see 6.2.4.2 Data
Preparation.
Customize this
MO on a list-
type sheet.
EnodebFlowCt
rlPara
EnodebFlowCt
rlPara
For details, see 6.2.4.2 Data
Preparation.
Customize this
MO on a list-
type sheet.
Using the CME to Perform Batch Configuration for Existing eNodeBs
For details, see Using the CME to Perform Batch Configuration for Existing eNodeBs in6.1.4.3 Activation.
Using the CME to Perform Single Configuration
On the CME, set the parameters listed in the "Data Preparation" section for a single eNodeB.
For detailed instructions, see Using the CME to Perform Single Configuration in 6.1.4.3
Activation described for feature activation.
Using MML Commands
Step 1 Run the MOD CELLDYNACBARALGOPARA command to set intelligent AC control parameters, including the statistic period, triggering threshold, canceling threshold, number of
periods in which the triggering condition is met, and number of periods in which the
canceling condition is met.
Step 2 Run the MOD CELLACBAR command to set other AC control parameters. The access type
can be emergency calls, MO data, MO signaling, multimedia telephony voice, multimedia
telephony video, or CSFB.
Step 3 Run the MOD CELLALGOSWITCH command to set the AC control mode to intelligent
AC control.
Step 4Run the MOD ENODEBFLOWCTRLPARA command to set the policy of determining
whether a cell is congested to flow control.
----End
MML Command Examples
MOD CELLDYNACBARALGOPARA: LocalCellId=0, DynAcBarTriggerThd =100,
DynAcBarCancelThd =80, DynAcBarStatPeriod=20, MoTriggerCondSatiPeriods=2,
MoCancelCondSatiPeriods=1;
MOD CELLACBAR: LocalCellId=0, AcBarringInfoCfgInd=CFG,
AcBarringForMoDataCfgInd=CFG, AcBarringFactorForCall=P95, AcBarTimeForCall=
ACCESS_BARRING_TIME_S4;
MOD CELLALGOSWITCH: LocalCellId=0, AcBarAlgoSwitch= ACBAR_SWITCH_DYNAMIC,
AcBarAlgoforDynSwitch= DYNAMIC_FOR_MO-1;MOD ENODEBFLOWCTRLPARA: DynAcBarPolicyMode=FLOWCONTROL;
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
46
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 52/90
6.2.4.4 Activation Observation
If the value of any of the following counters is not zero, intelligent AC control has been
activated:
l L.Dyn.ACBar.Trigger.Num: indicates the number of times intelligent AC control istriggered.
l L.Dyn.ACBar.Cancel.Num: indicates the number of times intelligent AC control is
canceled.
NOTE
If the AC control switch is adjusted after intelligent AC control is triggered and before it is cancelled,
the values of the preceding counters will be slightly different from those in scenarios without switch
adjustment. Here is an example for switch adjustment: ACBAR_SWITCH_DYNAMIC(dynamic
configuration) is changed to ACBAR_SWITCH_STATIC(static configuration) or
ACBAR_SWITCH_DISABLE(Disable).
6.2.4.5 Reconfiguration
For details, see 6.1.4.5 Reconfiguration.
6.2.4.6 Deactivation
For details, see 6.1.4.6 Deactivation.
6.2.5 Performance Monitoring
You can use the following methods for performance monitoring:
l Monitor the L.Dyn.ACBar.Trigger.Num and L.Dyn.ACBar.Cancel.Num counters. If
the values of these counters are always zero, the feature has not been triggered. In this
case, adjust the triggering threshold.
l If intelligent AC control has been triggered, monitor the
L.RRC.ConnReq.Msg.disc.FlowCtrl and L.RRC.SetupFail.Rej.FlowCtrl counters. If
the number of RRC connection request discards or rejections due to flow control
decreases, intelligent AC control has taken ef fect.
The decreased number of RRC connection request discards or rejections depends on the
proportion of UEs that support AC control, the access probability factor, and the access
barring duration. If a cell is seriously congested and the proportion of UEs that support AC
control is high, intelligent AC control can achieve high gains.
6.2.6 Parameter Optimization
Monitor the L.Dyn.ACBar.Trigger.Num and L.Dyn.ACBar.Cancel.Num counters. If the
counter values are always 0, this feature has not been triggered. In this case, adjust the
following parameters:
l CellDynAcBarAlgoPara. DynAcBarTriggerThd
l CellDynAcBarAlgoPara. DynAcBarCancelThd
l CellDynAcBarAlgoPara. MoTriggerCondSatiPeriods
l CellDynAcBarAlgoPara. MoCancelCondSatiPeriods
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
47
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 53/90
6.2.7 Troubleshooting
Fault Description
The values of L.Dyn.ACBar.Trigger.Num and L.Dyn.ACBar.Cancel.Num are always zero.This indicates that intelligent AC control has not been triggered.
The CPU usage (VS.BBUBoard.CPULoad.Mean ) of the main control board or a baseband
processing unit exceeds the flow control threshold (for example, 80%) for a long period (for
example, 15 minutes). In addition, the values of L.RRC.ConnReq.Msg.disc.FlowCtrl and
L.RRC.SetupFail.Rej.FlowCtrl indicate that RRC connection setup requests are discarded
or rejected due to flow control. In this case, it is deduced that a large number of random
access requests or RRC connection setup requests lead to long-term flow control and serious
cell congestion.
Troubleshooting
Step 1 Run the LST CELLALGOSWITCH command to check whether intelligent AC control is
enabled. If it is disabled, turn on the intelligent AC control switch.
Step 2 Run the LST CELLDYNACBARALGOPARA command to check the following parameters
and ensure they are correctly set:
l CellDynAcBarAlgoPara. DynAcBarStatPeriod
l CellDynAcBarAlgoPara. DynAcBarTriggerThd
l CellDynAcBarAlgoPara. DynAcBarCancelThd
l CellDynAcBarAlgoPara. MoTriggerCondSatiPeriods
l CellDynAcBarAlgoPara. MoCancelCondSatiPeriods
Step 3 If intelligent AC control is still not triggered, run the MOD
CELLDYNACBARALGOPARA command to set the following parameters to smaller
values:
l CellDynAcBarAlgoPara. DynAcBarStatPeriod
l CellDynAcBarAlgoPara. DynAcBarTriggerThd
l CellDynAcBarAlgoPara. DynAcBarCancelThd
l CellDynAcBarAlgoPara. MoTriggerCondSatiPeriods
l CellDynAcBarAlgoPara. MoCancelCondSatiPeriods
Step 4 If intelligent AC control is still not triggered, contact Huawei technical support.
----End
6.3 Dynamic SSAC
6.3.1 When to Use Dynamic SSAC
AC control has an impact on user access experience. If UE access is barred, the perceived
access delay increases. Therefore, AC control is recommended only when a large number of
UEs will simultaneously access the network, as in the case for special events such as holidays,concerts, and sporting events or for disasters such as earthquakes and tsunamis.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
48
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 54/90
Dynamic SSAC can be used when a large number of UEs will simultaneously initiate
multimedia telephony voice or video, as in the case for disasters such as earthquakes,
tsunamis, and hurricanes.
6.3.2 Required InformationCollect the following information before feature deployment:
l Whether UEs support AC control
Operators can obtain the distribution of various categories of UEs and the capability of
these UEs to support AC control from EPC information. Only UEs that support AC
control defined in 3GPP Release 9 and later can support this feature.
l Whether heavy traffic causes signaling shock to a network when a large number of UEs
in a cell simultaneously access the network
6.3.3 Planning
6.3.3.1 RF Planning
N/A
6.3.3.2 Network Planning
N/A
6.3.3.3 Hardware Planning
N/A
6.3.4 Deployment
6.3.4.1 Requirements
Other NEs
UEs must support the AC control mechanism defined in 3GPP Release 9.
License
The operator has purchased and activated the license for the feature listed in the following
table.
Feature ID Feature Name Model LicenseControl Item
NE Sales Unit
LOFD-008
002
Dynamic Service-
specific Access
Control
LT1S0DS
SAC00
Dynamic
Service-specific
Access Control
(FDD)
eNodeB per cell
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
49
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 55/90
6.3.4.2 Data Preparation
This section describes the data that you need to collect for setting parameters. Required data is
data that you must collect for all scenarios. Collect scenario-specific data when necessary for
a specific feature deployment scenario.
l For required data, see Table 6-1 and Table 6-2 in 6.1.4.2 Data Preparation.
l For scenario-specific data, see Table 6-8 and Table 6-9.
Table 6-8 Parameters that must be set in the CellDynAcBarAlgoPara MO to configure
dynamic SSAC parameters
ParameterName
Parameter ID DataSource
Setting Notes
Local Cell
ID
CellDynAcBa
rAlgoPara. LocalCellId
Network
plan(negotiation
not required)
This parameter specifies the local ID of a
cell. It uniquely identifies a cell withinthe coverage of an eNodeB.
Dynamic AC
Barring
Control
Statistic
Period
CellDynAcBa
rAlgoPara. Dy
nAcBarStatPe
riod
Network
plan
(negotiation
not required)
This parameter specifies a period for
measuring the proportion of cell
congestion duration.
Dynamic AC
Barring
Control
Trigger
Threshold
CellDynAcBa
rAlgoPara. Dy
nAcBarTrigge
rThd
Network
plan
(negotiation
not required)
This parameter specifies the threshold for
triggering dynamic AC barring in a cell.
This threshold is denoted by the
proportion of time that the cell is in the
congestion state. If the actual cell
congestion duration in a statistic period
(CellDynAcBarAlgo-
Para. DynAcBarStatPeriod ) is greater
than or equal to this threshold, the
condition for triggering dynamic AC
barring is met.
Dynamic AC
Barring
Control
Cancel
Threshold
CellDynAcBa
rAlgoPara. Dy
nAcBarCancel
Thd
Network
plan
(negotiation
not required)
This parameter specifies the threshold for
canceling dynamic AC barring in a cell.
This threshold is denoted by the
proportion of time that the cell is in the
congestion state. If the actual cell
congestion duration in a statistic period
(CellDynAcBarAlgo-
Para. DynAcBarStatPeriod ) is less than
or equal to this threshold, the condition
for canceling dynamic AC control is met.
Disaster
Reference
Indication
CellDynAcBa
rAlgoPara. Dis
asterReference
Ind
Network
plan
(negotiation
not required)
This parameter specifies the disaster
reference indications used for
determining whether a cell is in the
disaster state. This parameter applies only
to dynamic SSAC.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
50
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 56/90
ParameterName
Parameter ID DataSource
Setting Notes
Disaster
Duration
CellDynAcBa
rAlgoPara. Dis
asterDuration
Network
plan
(negotiation
not required)
This parameter specifies the duration that
the cell is in a disaster state. After the cell
enters a disaster state, the duration starts.
When the duration ends, the cell exits the
disaster state. This parameter applies only
to dynamic SSAC.
Ssac Trigger
Condition
Satisfied
Periods
CellDynAcBa
rAlgoPara. Ssa
cTriggerCond
SatiPeriods
Network
plan
(negotiation
not required)
This parameter specifies the number of
consecutive periods during which the
condition for triggering dynamic SSAC is
met.
Dynamic SSAC is triggered only when
the number of consecutive periods during
which the condition for triggeringdynamic SSAC is met reaches the value
of this parameter.
Ssac Cancel
Condition
Satisfied
Periods
CellDynAcBa
rAlgoPara. Ssa
cCancelCondS
atiPeriods
Network
plan
(negotiation
not required)
This parameter specifies the number of
consecutive periods during which the
condition for canceling dynamic SSAC is
met.
Dynamic SSAC is canceled only when
the number of consecutive periods during
which the condition for canceling
dynamic SSAC is met reaches the value
of this parameter.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
51
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 57/90
Table 6-9 Parameters that must be set in the EnodebFlowCtrlPara MO to configure
congestion decision policies used in dynamic SSAC
ParameterName
Parameter ID DataSource
Setting Notes
Dynamic AC
Barring
Policy Mode
EnodebFlowC
trlPara. DynA
cBarPolicyMo
de
Network
plan
(negotiation
not required)
This parameter specifies the policy of
determining cell congestion for intelligent
AC control or dynamic SSAC.
l When this parameter is set to
FLOWCONTROL(FLOWCONTR
OL), the eNodeB determines that a
cell is congested when the cell is
under flow control.
l When this parameter is set to
CPULOAD(CPULOAD), the
eNodeB determines whether a cell iscongested based on the configured
CPU load threshold. If the CPU load
of a cell's main control board or
baseband processing unit is greater
than or equal to the configured CPU
load threshold, the cell is congested.
The CPU load threshold is specified
by the
EnodebFlowCtrlPara.CpuLoadThd
parameter.
CPU LoadThreshold EnodebFlowCtrlPara.CpuL
oadThd
Network plan
(negotiation
not required)
This parameter specifies the CPU loadthreshold for determining whether a cell
is congested. This parameter takes effect
only when
EnodebFlowCtrlPara. DynAcBarPolicy
Mode is set to CPULOAD(CPULOAD).
If the CPU load of a cell's main control
board or baseband processing unit is
greater than or equal to this parameter
value, the cell is congested. If the CPU
load is less than this parameter value, the
cell is not congested.
6.3.4.3 Activation
Using the CME to Perform Batch Configuration for Newly Deployed eNodeBs
Enter the values of the parameters listed in Table 6-10 in a summary data file, which also
contains other data for the new eNodeBs to be deployed. Then, import the summary data file
into the CME for batch configuration. For detailed instructions, see "Creating eNodeBs in
Batches" in the initial configuration guide for the eNodeB, which is available in the eNodeB
product documentation.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
52
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 58/90
The summary data file may be a scenario-specific file provided by the CME or a customized
file, depending on the following conditions:
l The MOs in Table 6-10 are contained in a scenario-specific summary data file. In this
situation, set the parameters in the MOs, and then verify and save the file.
l Some MOs in Table 6-10 are not contained in a scenario-specific summary data file. In
this situation, customize a summary data file to include the MOs before you can set the
parameters.
Table 6-10 Parameters related to dynamic SSAC
MO Sheet in theSummaryData File
Parameter Group Remarks
CellAcBar CellAcBar For details, see 6.1.4.2
Data Preparation.
Customize this MO on a
pattern-type sheet.
CellAlgoSwitc
h
CellAlgoSwitc
h
For details, see 6.1.4.2
Data Preparation.
Customize this MO on a
pattern-type sheet.
CellDynAcBar
AlgoPara
CellDynAcBar
AlgoPara
For details, see 6.3.4.2
Data Preparation.
Customize this MO on a
list-type sheet.
EnodebFlowCt
rlPara
EnodebFlowCt
rlPara
For details, see 6.3.4.2
Data Preparation.
Customize this MO on a
list-type sheet.
Using the CME to Perform Batch Configuration for Existing eNodeBs
For details, see Using the CME to Perform Batch Configuration for Existing eNodeBs in
6.1.4.3 Activation.
Using the CME to Perform Single Configuration
On the CME, set the parameters listed in the "Data Preparation" section for a single eNodeB.
For detailed instructions, see Using the CME to Perform Single Configuration in 6.1.4.3
Activation described for feature activation.
Using MML Commands
Step 1 Run the MOD CELLDYNACBARALGOPARA command to set dynamic SSAC
parameters, including the statistic period, triggering condition, canceling threshold, number of
periods in which the triggering condition is met, number of periods in which the canceling
condition is met, disaster reference indication, and disaster duration.
Step 2 Run the MOD CELLACBAR command to set other AC control parameters. The access type
can be emergency calls, MO data, MO signaling, multimedia telephony voice, multimedia
telephony video, or CSFB.
Step 3 Run the MOD CELLALGOSWITCH command to set the AC control mode to dynamic
SSAC.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
53
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 59/90
Step 4 Run the MOD ENODEBFLOWCTRLPARA command to set the policy of determining
whether a cell is congested to flow control.
----End
MML Command ExamplesMOD CELLDYNACBARALGOPARA: LocalCellId=0, DynAcBarTriggerThd =100,
DynAcBarCancelThd =80, DynAcBarStatPeriod=20, SsacTriggerCondSatiPeriods=2,
SsacCancelCondSatiPeriods=1, DisasterReferenceInd=ETWS_PN-1, DisasterDuration=60;
MOD CELLACBAR: LocalCellId=0, AcBarringInfoCfgInd=CFG, AcBarForMVoiceCfgInd=CFG,
AcBarFactorForMVoice=P95, AcBarTimeForMVoice= ACCESS_BARRING_TIME_S4;
MOD CELLALGOSWITCH: LocalCellId=0, AcBarAlgoSwitch= ACBAR_SWITCH_DYNAMIC,
AcBarAlgoforDynSwitch=DYNAMIC_FOR_SSAC-1;
MOD ENODEBFLOWCTRLPARA: DynAcBarPolicyMode=FLOWCONTROL;
6.3.4.4 Activation Observation
If the value of any of the following counters is not zero, dynamic SSAC has been activated:
l L.SSAC.Dyn.ACBar.Trigger.Num: indicates the number of times AC barring for
dynamic SSAC is triggered.
l L.SSAC.Dyn.ACBar.Cancel.Num: Indicates the number of times AC barring for
dynamic SSAC is canceled.
NOTE
If the AC control switch is adjusted after dynamic SSAC is triggered and before it is cancelled, the
L.SSAC.Dyn.ACBar.Trigger.Num and L.SSAC.Dyn.ACBar.Cancel.Num counter values will be
slightly different from those in scenarios without switch adjustment. Here is an example for switch
adjustment: ACBAR_SWITCH_DYNAMIC(dynamic configuration) is changed to
ACBAR_SWITCH_STATIC(static configuration) or ACBAR_SWITCH_DISABLE(Disable).
6.3.4.5 Reconfiguration
For details, see 6.1.4.5 Reconfiguration.
6.3.4.6 Deactivation
For details, see 6.1.4.6 Deactivation.
6.3.5 Performance Monitoring
You can use the following methods for performance monitoring:
l Monitor the L.SSAC.Dyn.ACBar.Trigger.Num and L.SSAC.Dyn.ACBar.Cancel.Num
counters. If the values of these counters are always zero, dynamic SSAC has not been
triggered. In this case, adjust the triggering threshold.
l If dynamic SSAC has been triggered, monitor the L.RRC.ConnReq.Msg.disc.FlowCtrl
and L.RRC.SetupFail.Rej.FlowCtrl counters. If the number of RRC connection request
discards or rejections due to flow control decreases, dynamic SSAC has taken effect.
The decreased number of RRC connection request discards or rejections depends on the
proportion of UEs that support SSAC, the access probability factor, and the access barring
duration. If a cell is seriously congested because a large number of UEs simultaneously
initiate access for multimedia telephony voice and video and the proportion of UEs thatsupport SSAC is high, dynamic SSAC can achieve high gains.
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
54
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 60/90
6.3.6 Parameter Optimization
Monitor the L.SSAC.Dyn.ACBar.Trigger.Num and L.SSAC.Dyn.ACBar.Cancel.Num
counters. If the counter values are always 0, this feature has not been triggered. In this case,
adjust the following parameters:
l CellDynAcBarAlgoPara. DynAcBarTriggerThd
l CellDynAcBarAlgoPara. DynAcBarCancelThd
l CellDynAcBarAlgoPara. SsacTriggerCondSatiPeriods
l CellDynAcBarAlgoPara. SsacCancelCondSatiPeriods
6.3.7 Troubleshooting
Fault Description
The values of L.SSAC.Dyn.ACBar.Trigger.Num and L.SSAC.Dyn.ACBar.Cancel.Num
are always zero. This indicates that dynamic SSAC has not been triggered.
The CPU usage (VS.BBUBoard.CPULoad.Mean ) of the main control board or a baseband
processing unit exceeds the flow control threshold (for example, 80%) for a long period (for
example, 15 minutes). In addition, the values of L.RRC.ConnReq.Msg.disc.FlowCtrl and
L.RRC.SetupFail.Rej.FlowCtrl indicate that RRC connection setup requests are discarded
or rejected due to flow control. In this case, it is deduced that a large number of random
access requests or RRC connection setup requests lead to long-term flow control and serious
cell congestion.
Troubleshooting Step 1 Run the LST CELLALGOSWITCH command to check whether dynamic SSAC is enabled.
If it is disabled, turn on the dynamic SSAC switch.
Step 2 Run the LST CELLDYNACBARALGOPARA command to check whether the
CellDynAcBarAlgoPara. DisasterReferenceInd and
CellDynAcBarAlgoPara. DisasterDuration parameters are correctly configured. If
CellDynAcBarAlgoPara. DisasterReferenceInd is set, check whether the eNodeB has
received a disaster notification message from the metadata management entity (MME) for the
current cell.
Step 3 Run the LST CELLDYNACBARALGOPARA command to check the following parameters
and ensure they are correctly set:
l CellDynAcBarAlgoPara. DynAcBarStatPeriod
l CellDynAcBarAlgoPara. DynAcBarTriggerThd
l CellDynAcBarAlgoPara. DynAcBarCancelThd
l CellDynAcBarAlgoPara. SsacTriggerCondSatiPeriods
l CellDynAcBarAlgoPara. SsacCancelCondSatiPeriods
Step 4 If dynamic SSAC is still not triggered, run the MOD CELLDYNACBARALGOPARA
command to set the following parameters to smaller values:
l CellDynAcBarAlgoPara. DynAcBarStatPeriod
l CellDynAcBarAlgoPara. DynAcBarTriggerThd
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
55
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 61/90
l CellDynAcBarAlgoPara. DynAcBarCancelThd
l CellDynAcBarAlgoPara. SsacTriggerCondSatiPeriods
l CellDynAcBarAlgoPara. SsacCancelCondSatiPeriods
Step 5 If dynamic SSAC is still not triggered, contact Huawei technical support.
----End
eRAN
Access Class Control Feature Parameter Description 6 Engineering Guidelines
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
56
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 62/90
7 Parameters
Table 7-1 Parameters
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAlg
oSwitch
AcBarA
lgoforD
ynSwitc
h
MOD
CELLA
LGOSW
ITCH
LST
CELLA
LGOSW
ITCH
LOFD-0
08002 /
TDLOF
D-08020
2
LOFD-0
70207 /
TDLOFD-08122
2
Dynami
c
Service
Specific
Access
Control
Intellige
ntAccess
Class
Control
Meaning:
Indicates whether to enable intelligent access barring
algorithms. This parameter controls whether to enable
intelligent access barring on mobile-originated (MO)
signaling, MO data, service specific access control
(SSAC) for multimedia telephony (MMTEL) voice
services, or SSAC for MMTEL video services. This
parameter takes effect only when theAcBarAlgoSwitch parameter in the CellAlgoSwitch
MO is set to ACBAR_SWITCH_DYNAMIC.
DYNAMIC_FOR_MO: Indicates whether to enable
intelligent access barring on UEs running MO
signaling or MO data.
If this switch is on, intelligent access barring applies
to UEs running MO signaling or MO data.
If this switch is off, intelligent access barring does not
apply to UEs running MO signaling or MO data.
DYNAMIC_FOR_SSAC: Indicates whether to enable
intelligent access barring on UEs running MMTEL
voices services or MMTEL video services.
If this switch is on, intelligent access barring applies
to UEs running MMTEL voices services or MMTEL
video services.
If this switch is off, intelligent access barring does not
apply to UEs running MMTEL voices services or
MMTEL video services.
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
57
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 63/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
GUI Value Range:
DYNAMIC_FOR_MO(DYNAMIC_FOR_MO),
DYNAMIC_FOR_SSAC(DYNAMIC_FOR_SSAC)
Unit: None
Actual Value Range: DYNAMIC_FOR_MO,
DYNAMIC_FOR_SSAC
Default Value: DYNAMIC_FOR_MO:On,
DYNAMIC_FOR_SSAC:Off
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
58
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 64/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellDyn
AcBarA
lgoPara
Disaster
Referen
ceInd
MOD
CELLD
YNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
08002 /
TDLOF
D-00800
2
Dynami
c
Service
Specific
Access
Control
Meaning:
Indicates the disaster reference indications used for
determining whether a cell is in the disaster state. If all
switches included in this parameter are off, the
disaster state of the cell does not need to be
determined.
ETWS_PN: Indicates whether Primary notifications
(PNs) in the earthquake and tsunami warning system
(ETWS) is used in the disaster state determination.
The PNs for ETWS do not include PNs used for
ETWS tests.
If this switch is on, PNs in ETWS are used in thedisaster state determination.
If this switch is off, PNs in ETWS are not used in the
disaster state determination.
ETWS_PN_TEST: Indicates whether PNs for ETWS
tests are used in the disaster state determination.
If this switch is on, PNs in ETWS tests are used in the
disaster state determination.
If this switch is off, PNs in ETWS tests are not used in
the disaster state determination.
CMAS: Indicates whether commercial mobile alert
system (CMAS) warning notifications are used in the
disaster state determination.
If this switch is on, CMAS warning notifications are
used in the disaster state determination.
If this switch is off, CMAS warning notifications are
not used in the disaster state determination.
GUI Value Range: ETWS_PN(ETWS PN),
ETWS_PN_TEST(ETWS PN FOR TEST),
CMAS(CMAS)
Unit: None
Actual Value Range: ETWS_PN, ETWS_PN_TEST,
CMAS
Default Value: ETWS_PN:On, ETWS_PN_TEST:Off,
CMAS:Off
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
59
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 65/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellDyn
AcBarA
lgoPara
Disaster
Duration
MOD
CELLD
YNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
08002 /
TDLOF
D-00800
2
Dynami
c
Service
Specific
Access
Control
Meaning: Indicates the duration that the cell is in the
disaster state. The cell is out of the disaster state after
the duration specified by this parameter ends.
GUI Value Range: 1~10080
Unit: min
Actual Value Range: 1~10080
Default Value: 60
CellDyn
AcBarAlgoPara
SsacTrig
gerCondSatiPeri
ods
MOD
CELLDYNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
08002 /TDLOF
D-00800
2
Dynami
cService
Specific
Access
Control
Meaning: Indicates the number of periods for
triggering intelligent access barring on specificservices. If related triggering conditions are met in
consecutive periods specified by this parameter,
intelligent access barring on specific services is
triggered.
GUI Value Range: 1~1000
Unit: None
Actual Value Range: 1~1000
Default Value: 2
CellDyn
AcBarAlgoPara
SsacCan
celCondSatiPeri
ods
MOD
CELLDYNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
08002 /TDLOF
D-00800
2
Dynami
cService
Specific
Access
Control
Meaning: Indicates the number of periods for
canceling intelligent access barring on specificservices. If related cancellation conditions are met in
consecutive periods specified by this parameter,
intelligent access barring on specific services is
canceled.
GUI Value Range: 1~1000
Unit: None
Actual Value Range: 1~1000
Default Value: 1
CellDyn
AcBarAlgoPara
MoTrig
gerCondSatiPeri
ods
MOD
CELLDYNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
70207 /TDLOF
D-07020
7
Intellige
ntAccess
Class
Control
Meaning: Indicates the number of consecutive periods
for triggering intelligent access class control onmobile-originated (MO) calls or signaling if related
triggering conditions are met.
GUI Value Range: 1~1000
Unit: None
Actual Value Range: 1~1000
Default Value: 2
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
60
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 66/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellDyn
AcBarA
lgoPara
MoCanc
elCondS
atiPerio
ds
MOD
CELLD
YNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
70207 /
TDLOF
D-07020
7
Intellige
nt
Access
Class
Control
Meaning: Indicates the number of consecutive periods
for canceling intelligent access class control on
mobile-originated (MO) calls or signaling if related
cancellation conditions are met.
GUI Value Range: 1~1000
Unit: None
Actual Value Range: 1~1000
Default Value: 1
eNodeB
FlowCtr lPara
DynAcB
arPolicyMode
MOD
ENODEBFLOW
CTRLP
ARA
LST
ENODE
BFLOW
CTRLP
ARA
LOFD-0
70207 /TDLOF
D-07020
7
LOFD-0
08002 /
TDLOF
D-00800
2
Intellige
ntAccess
Class
Control
Dynami
c
Service
Specific
Access
Control(
SSAC)
Meaning:
Indicates the policy for determining whether cells arecongested in intelligent access control or service-
based dynamic access control.
If this parameter is set to
FLOWCONTROL(FLOWCONTROL), cell
congestion is determined based on the flow control
state.
If this parameter is set to CPULOAD(CPULOAD),
cell congestion is determined based on the configured
CPU load threshold. If the CPU load of a main control
board or baseband processing unit serving the cells is
greater than or equal to the configured CPU load
threshold, the cells are congested. The CPU load
threshold is specified by the CpuLoadThd parameter.
GUI Value Range:
FLOWCONTROL(FLOWCONTROL),
CPULOAD(CPULOAD)
Unit: None
Actual Value Range: FLOWCONTROL, CPULOAD
Default Value: FLOWCONTROL(FLOWCONTROL)
eNodeBFlowCtr
lPara
CpuLoadThd MODENODE
BFLOW
CTRLP
ARA
LST
ENODE
BFLOW
CTRLP
ARA
LOFD-070207 /
TDLOF
D-07020
7
LOFD-0
08002 /
TDLOF
D-00800
2
Intelligent
Access
Class
Control
Dynami
c
Service
Specific
Access
Control(
SSAC)
Meaning: Indicates the CPU load threshold of a board.If the CPU load of a main control board or baseband
processing unit serving the cells is greater than or
equal to this parameter value, the cells are congested.
If the CPU load is less than this parameter value, the
cells are not congested. This parameter takes effect
only when the DynAcBarPolicyMode parameter is set
to CPULOAD(CPULOAD).
GUI Value Range: 50~100
Unit: %
Actual Value Range: 50~100
Default Value: 80
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
61
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 67/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarri
ngInfoC
fgInd
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates whether to configure the access
barring information.
GUI Value Range: NOT_CFG(Not configure),
CFG(Configure)
Unit: None
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(Not configure)
CellAlg
oSwitch
AcBarA
lgoSwitc
h
MOD
CELLA
LGOSW
ITCHLST
CELLA
LGOSW
ITCH
LBFD-0
02009 /
TDLBF
D-002009
LOFD-0
700206 /
TLOFD-
0700206
Broadca
st of
system
information
Dynami
c AC
Barring
Meaning: Indicates the switch for the access barring
algorithm. If this parameter is set to
ACBAR_SWITCH_DYNAMIC, intelligent access
barring is enabled. In this situation, the access probability factors for mobile-originated data and
mobile-originated signaling are dynamically adjusted
based on the cell load. If this parameter is set to
ACBAR_SWITCH_STATIC, static access barring is
enabled. In this situation, the access probability
factors and average access barring durations are
configured in the access barring information. If this
parameter is set to ACBAR_SWITCH_DISABLE,
access barring is disabled.
GUI Value Range:
ACBAR_SWITCH_DYNAMIC(dynamic
configuration), ACBAR_SWITCH_STATIC(staticconfiguration),
ACBAR_SWITCH_DISABLE(Disable)
Unit: None
Actual Value Range: ACBAR_SWITCH_DYNAMIC,
ACBAR_SWITCH_STATIC,
ACBAR_SWITCH_DISABLE
Default Value: ACBAR_SWITCH_STATIC(static
configuration)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
62
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 68/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarri
ngForE
mergenc
y
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02028 /
TDLBF
D-00202
8
Emerge
ncy Call
Meaning:
Indicates the emergency call barring status of access
class 10, indicating whether UEs of access class 10
can initiate emergency calls.
If this parameter is set to BOOLEAN_TRUE, UEs of
access classes 0 to 9 or those without IMSIs cannot
initiate emergency calls. If this parameter is set to
BOOLEAN_FALSE, UEs of access classes 0 to 9 and
those without IMSIs can initiate emergency calls.
A UE in access classes 11 to 15 cannot initiate
emergency calls only when its access class and access
class 10 are both barred. If its access class or accessclass 10 is not barred, emergency calls initiated by the
UE are granted access.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
CellAcB
ar
AcBarri
ngForM
oDataCf
gInd
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates whether to configure the access
barring information for mobile-originated calls.
GUI Value Range: NOT_CFG(Not configure),
CFG(Configure)
Unit: None
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(Not configure)
CellAcB
ar
AcBarri
ngForM
oSigCfg
Ind
MOD
CELLA
CBAR
LSTCELLA
CBAR
LBFD-0
02009 /
TDLBF
D-002009
Broadca
st of
system
information
Meaning: Indicates whether to configure the access
barring information for signaling.
GUI Value Range: NOT_CFG(Not configure),
CFG(Configure)Unit: None
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(Not configure)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
63
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 69/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarF
orMVoic
eCfgInd
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates whether to configure the access
barring information for multimedia telephony
(MMTEL) voice services.
GUI Value Range: NOT_CFG(Not configure),
CFG(Configure)
Unit: None
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(Not configure)
CellAcB
ar
AcBarF
orMVid
eoCfgInd
MOD
CELLA
CBAR LST
CELLA
CBAR
LBFD-0
02009 /
TDLBFD-00200
9
Broadca
st of
systeminformat
ion
Meaning: Indicates whether to configure the access
barring information for multimedia telephony
(MMTEL) video services.GUI Value Range: NOT_CFG(Not configure),
CFG(Configure)
Unit: None
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(Not configure)
CellAcB
ar
AcBarF
orCsfbC
fgInd
MOD
CELLA
CBAR
LST
CELLACBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates whether to configure the access
barring information for CS fallback (CSFB) services.
GUI Value Range: NOT_CFG(Not configure),
CFG(Configure)
Unit: None
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(Not configure)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
64
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 70/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarTi
meForC
all
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates the average access barring
duration for mobile-originated calls.
GUI Value Range:
ACCESS_BARRING_TIME_S4(4s),
ACCESS_BARRING_TIME_S8(8s),
ACCESS_BARRING_TIME_S16(16s),
ACCESS_BARRING_TIME_S32(32s),
ACCESS_BARRING_TIME_S64(64s),
ACCESS_BARRING_TIME_S128(128s),
ACCESS_BARRING_TIME_S256(256s),
ACCESS_BARRING_TIME_S512(512s)
Unit: s
Actual Value Range:
ACCESS_BARRING_TIME_S4,
ACCESS_BARRING_TIME_S8,
ACCESS_BARRING_TIME_S16,
ACCESS_BARRING_TIME_S32,
ACCESS_BARRING_TIME_S64,
ACCESS_BARRING_TIME_S128,
ACCESS_BARRING_TIME_S256,
ACCESS_BARRING_TIME_S512
Default Value: ACCESS_BARRING_TIME_S4(4s)
CellAcBar
AcBarringFactor
ForCall
MODCELLA
CBAR
LST
CELLA
CBAR
LBFD-002009 /
TDLBF
D-00200
9
Broadcast of
system
informat
ion
Meaning: Indicates the access probability factor for mobile-originated calls. A mobile-originated call is
granted access if the random number generated by the
UE is less than this access probability factor;
otherwise, the access request is rejected. According to
3GPP TS 36.331, if any of the parameters
AC11BarforCall, AC12BarforCall, AC13BarforCall,
AC14BarforCall, and AC15BarforCall is set to
BOOLEAN_TRUE, the eNodeB sends UEs P00 as
the access probability factor for mobile-originated
calls in the system information block type 2 (SIB2),
regardless of the actual setting of the
AcBarringFactorForCall parameter.
GUI Value Range: P00(0%), P05(5%), P10(10%),
P15(15%), P20(20%), P25(25%), P30(30%),
P40(40%), P50(50%), P60(60%), P70(70%),
P75(75%), P80(80%), P85(85%), P90(90%),
P95(95%)
Unit: %
Actual Value Range: P00, P05, P10, P15, P20, P25,
P30, P40, P50, P60, P70, P75, P80, P85, P90, P95
Default Value: P95(95%)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
65
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 71/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AC11Ba
rforCall
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the mobile-originated call barring status of
access class 11, indicating whether UEs of access
class 11 can initiate mobile-originated calls.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 11 cannot initiate mobile-originated calls.
If this parameter is set to BOOLEAN_FALSE, UEs of
access class 11 can initiate mobile-originated calls.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
CellAcB
ar
AC12Ba
rforCall
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the mobile-originated call barring status of
access class 12, indicating whether UEs of access
class 12 can initiate mobile-originated calls.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 12 cannot initiate mobile-originated calls.
If this parameter is set to BOOLEAN_FALSE, UEs of access class 12 can initiate mobile-originated calls.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
66
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 72/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AC13Ba
rforCall
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the mobile-originated call barring status of
access class 13, indicating whether UEs of access
class 13 can initiate mobile-originated calls.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 13 cannot initiate mobile-originated calls.
If this parameter is set to BOOLEAN_FALSE, UEs of
access class 13 can initiate mobile-originated calls.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
CellAcB
ar
AC14Ba
rforCall
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the mobile-originated call barring status of
access class 14, indicating whether UEs of access
class 14 can initiate mobile-originated calls.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 14 cannot initiate mobile-originated calls.
If this parameter is set to BOOLEAN_FALSE, UEs of access class 14 can initiate mobile-originated calls.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
67
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 73/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AC15Ba
rforCall
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the mobile-originated call barring status of
access class 15, indicating whether UEs of access
class 15 can initiate mobile-originated calls.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 15 cannot initiate mobile-originated calls.
If this parameter is set to BOOLEAN_FALSE, UEs of
access class 15 can initiate mobile-originated calls.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
CellAcB
ar
AcBarTi
meForSi
g
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates the average access barring
duration for signaling.
GUI Value Range:
ACCESS_BARRING_TIME_S4(4s),
ACCESS_BARRING_TIME_S8(8s),
ACCESS_BARRING_TIME_S16(16s),
ACCESS_BARRING_TIME_S32(32s),
ACCESS_BARRING_TIME_S64(64s),ACCESS_BARRING_TIME_S128(128s),
ACCESS_BARRING_TIME_S256(256s),
ACCESS_BARRING_TIME_S512(512s)
Unit: s
Actual Value Range:
ACCESS_BARRING_TIME_S4,
ACCESS_BARRING_TIME_S8,
ACCESS_BARRING_TIME_S16,
ACCESS_BARRING_TIME_S32,
ACCESS_BARRING_TIME_S64,
ACCESS_BARRING_TIME_S128,ACCESS_BARRING_TIME_S256,
ACCESS_BARRING_TIME_S512
Default Value: ACCESS_BARRING_TIME_S4(4s)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
68
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 74/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarri
ngFactor
ForSig
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates the access probability factor for
signaling. Signaling from a UE is granted access if the
random number generated by the UE is less than this
access probability factor; otherwise, the access request
is rejected. According to 3GPP TS 36.331, if any of
the parameters AC11BarForSig, AC12BarForSig,
AC13BarForSig, AC14BarForSig, and
AC15BarForSig is set to BOOLEAN_TRUE, the
eNodeB sends UEs P00 as the access probability
factor for signaling in the system information block
type 2 (SIB2), regardless of the actual setting of the
AcBarringFactorForSig parameter.
GUI Value Range: P00(0%), P05(5%), P10(10%),P15(15%), P20(20%), P25(25%), P30(30%),
P40(40%), P50(50%), P60(60%), P70(70%),
P75(75%), P80(80%), P85(85%), P90(90%),
P95(95%)
Unit: %
Actual Value Range: P00, P05, P10, P15, P20, P25,
P30, P40, P50, P60, P70, P75, P80, P85, P90, P95
Default Value: P95(95%)
CellAcB
ar
AC11Ba
rForSig
MOD
CELLACBAR
LST
CELLA
CBAR
LBFD-0
02009 /TDLBF
D-00200
9
Broadca
st of system
informat
ion
Meaning:
Indicates the signaling barring status of access class11, indicating whether UEs of access class 11 can
initiate signaling access.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 11 cannot initiate signaling access. If this
parameter is set to BOOLEAN_FALSE, UEs of access
class 11 can initiate signaling access.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
69
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 75/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AC12Ba
rForSig
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the signaling barring status of access class
12, indicating whether UEs of access class 12 can
initiate signaling access.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 12 cannot initiate signaling access. If this
parameter is set to BOOLEAN_FALSE, UEs of access
class 12 can initiate signaling access.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
CellAcB
ar
AC13Ba
rForSig
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the signaling barring status of access class
13, indicating whether UEs of access class 13 can
initiate signaling access.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 13 cannot initiate signaling access. If this
parameter is set to BOOLEAN_FALSE, UEs of accessclass 13 can initiate signaling access.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
70
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 76/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AC14Ba
rForSig
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the signaling barring status of access class
14, indicating whether UEs of access class 14 can
initiate signaling access.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 14 cannot initiate signaling access. If this
parameter is set to BOOLEAN_FALSE, UEs of access
class 14 can initiate signaling access.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
CellAcB
ar
AC15Ba
rForSig
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates the signaling barring status of access class
15, indicating whether UEs of access class 15 can
initiate signaling access.
If this parameter is set to BOOLEAN_TRUE, UEs of
access class 15 cannot initiate signaling access. If this
parameter is set to BOOLEAN_FALSE, UEs of accessclass 15 can initiate signaling access.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE,
BOOLEAN_TRUE
Default Value: BOOLEAN_FALSE(False)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
71
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 77/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarTi
meForM
Voice
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates the average access barring time of
multimedia telephony (MMTEL) voice services.
GUI Value Range:
ACCESS_BARRING_TIME_S4(4s),
ACCESS_BARRING_TIME_S8(8s),
ACCESS_BARRING_TIME_S16(16s),
ACCESS_BARRING_TIME_S32(32s),
ACCESS_BARRING_TIME_S64(64s),
ACCESS_BARRING_TIME_S128(128s),
ACCESS_BARRING_TIME_S256(256s),
ACCESS_BARRING_TIME_S512(512s)
Unit: s
Actual Value Range:
ACCESS_BARRING_TIME_S4,
ACCESS_BARRING_TIME_S8,
ACCESS_BARRING_TIME_S16,
ACCESS_BARRING_TIME_S32,
ACCESS_BARRING_TIME_S64,
ACCESS_BARRING_TIME_S128,
ACCESS_BARRING_TIME_S256,
ACCESS_BARRING_TIME_S512
Default Value: ACCESS_BARRING_TIME_S4(4s)
CellAcBar
AcBarFactorFor
MVoice
MODCELLA
CBAR
LST
CELLA
CBAR
LBFD-002009 /
TDLBF
D-00200
9
Broadcast of
system
informat
ion
Meaning: Indicates the access probability factor for multimedia telephony (MMTEL) voice services. An
MMTEL voice service is granted access if the random
number generated by the UE is less than this access
probability factor; otherwise, the access request is
barred.
GUI Value Range: P00(0%), P05(5%), P10(10%),
P15(15%), P20(20%), P25(25%), P30(30%),
P40(40%), P50(50%), P60(60%), P70(70%),
P75(75%), P80(80%), P85(85%), P90(90%),
P95(95%)
Unit: %Actual Value Range: P00, P05, P10, P15, P20, P25,
P30, P40, P50, P60, P70, P75, P80, P85, P90, P95
Default Value: P95(95%)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
72
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 78/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
Special
ACBarF
orMVoic
e
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates whether multimedia telephony (MMTEL)
voice services initiated by UEs of AC 11 to AC 15 are
granted access.
AC11BARSTATE: If this option is selected, the
MMTEL voice services initiated by UEs of AC 11 in
idle mode are barred.
AC12BARSTATE: If this option is selected, the
MMTEL voice services initiated by UEs of AC 12 in
idle mode are barred.
AC13BARSTATE: If this option is selected, theMMTEL voice services initiated by UEs of AC 13 in
idle mode are barred.
AC14BARSTATE: If this option is selected, the
MMTEL voice services initiated by UEs of AC 14 in
idle mode are barred.
AC15BARSTATE: If this option is selected, the
MMTEL voice services initiated by UEs of AC 15 in
idle mode are barred.
GUI Value Range:
AC11BARSTATE(AC11BARSTATE),AC12BARSTATE(AC12BARSTATE),
AC13BARSTATE(AC13BARSTATE),
AC14BARSTATE(AC14BARSTATE),
AC15BARSTATE(AC15BARSTATE)
Unit: None
Actual Value Range: AC11BARSTATE,
AC12BARSTATE, AC13BARSTATE,
AC14BARSTATE, AC15BARSTATE
Default Value: AC11BARSTATE:Permit,
AC12BARSTATE:Permit, AC13BARSTATE:Permit,
AC14BARSTATE:Permit, AC15BARSTATE:Permit
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
73
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 79/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarTi
meForM
Video
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates the average access barring time of
multimedia telephony (MMTEL) video services.
GUI Value Range:
ACCESS_BARRING_TIME_S4(4s),
ACCESS_BARRING_TIME_S8(8s),
ACCESS_BARRING_TIME_S16(16s),
ACCESS_BARRING_TIME_S32(32s),
ACCESS_BARRING_TIME_S64(64s),
ACCESS_BARRING_TIME_S128(128s),
ACCESS_BARRING_TIME_S256(256s),
ACCESS_BARRING_TIME_S512(512s)
Unit: s
Actual Value Range:
ACCESS_BARRING_TIME_S4,
ACCESS_BARRING_TIME_S8,
ACCESS_BARRING_TIME_S16,
ACCESS_BARRING_TIME_S32,
ACCESS_BARRING_TIME_S64,
ACCESS_BARRING_TIME_S128,
ACCESS_BARRING_TIME_S256,
ACCESS_BARRING_TIME_S512
Default Value: ACCESS_BARRING_TIME_S4(4s)
CellAcBar
AcBarFactorFor
MVideo
MODCELLA
CBAR
LST
CELLA
CBAR
LBFD-002009 /
TDLBF
D-00200
9
Broadcast of
system
informat
ion
Meaning: Indicates the access probability factor for multimedia telephony (MMTEL) video services. An
MMTEL video service is granted access if the random
number generated by the UE is less than this access
probability factor; otherwise, the access request is
barred.
GUI Value Range: P00(0%), P05(5%), P10(10%),
P15(15%), P20(20%), P25(25%), P30(30%),
P40(40%), P50(50%), P60(60%), P70(70%),
P75(75%), P80(80%), P85(85%), P90(90%),
P95(95%)
Unit: %Actual Value Range: P00, P05, P10, P15, P20, P25,
P30, P40, P50, P60, P70, P75, P80, P85, P90, P95
Default Value: P95(95%)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
74
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 80/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
Special
ACBarF
orMVid
eo
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates whether multimedia telephony (MMTEL)
video services initiated by UEs of AC 11 to AC 15 are
granted access.
AC11BARSTATE: If this option is selected, the
MMTEL video services initiated by UEs of AC 11 in
idle mode are barred.
AC12BARSTATE: If this option is selected, the
MMTEL video services initiated by UEs of AC 12 in
idle mode are barred.
AC13BARSTATE: If this option is selected, theMMTEL video services initiated by UEs of AC 13 in
idle mode are barred.
AC14BARSTATE: If this option is selected, the
MMTEL video services initiated by UEs of AC 14 in
idle mode are barred.
AC15BARSTATE: If this option is selected, the
MMTEL video services initiated by UEs of AC 15 in
idle mode are barred.
GUI Value Range:
AC11BARSTATE(AC11BARSTATE),AC12BARSTATE(AC12BARSTATE),
AC13BARSTATE(AC13BARSTATE),
AC14BARSTATE(AC14BARSTATE),
AC15BARSTATE(AC15BARSTATE)
Unit: None
Actual Value Range: AC11BARSTATE,
AC12BARSTATE, AC13BARSTATE,
AC14BARSTATE, AC15BARSTATE
Default Value: AC11BARSTATE:Permit,
AC12BARSTATE:Permit, AC13BARSTATE:Permit,
AC14BARSTATE:Permit, AC15BARSTATE:Permit
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
75
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 81/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
AcBarTi
meForC
sfb
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning: Indicates the average access barring time of
CS fallback (CSFB) services.
GUI Value Range:
ACCESS_BARRING_TIME_S4(4s),
ACCESS_BARRING_TIME_S8(8s),
ACCESS_BARRING_TIME_S16(16s),
ACCESS_BARRING_TIME_S32(32s),
ACCESS_BARRING_TIME_S64(64s),
ACCESS_BARRING_TIME_S128(128s),
ACCESS_BARRING_TIME_S256(256s),
ACCESS_BARRING_TIME_S512(512s)
Unit: s
Actual Value Range:
ACCESS_BARRING_TIME_S4,
ACCESS_BARRING_TIME_S8,
ACCESS_BARRING_TIME_S16,
ACCESS_BARRING_TIME_S32,
ACCESS_BARRING_TIME_S64,
ACCESS_BARRING_TIME_S128,
ACCESS_BARRING_TIME_S256,
ACCESS_BARRING_TIME_S512
Default Value: ACCESS_BARRING_TIME_S4(4s)
CellAcBar
AcBarFactorFor
Csfb
MODCELLA
CBAR
LST
CELLA
CBAR
LBFD-002009 /
TDLBF
D-00200
9
Broadcast of
system
informat
ion
Meaning: Indicates the access probability factor for CS fallback (CSFB) services. If the random number
generated by a UE is less than the parameter value, the
eNodeB accepts the CSFB service access request;
otherwise, the eNodeB rejects the access request.
GUI Value Range: P00(0%), P05(5%), P10(10%),
P15(15%), P20(20%), P25(25%), P30(30%),
P40(40%), P50(50%), P60(60%), P70(70%),
P75(75%), P80(80%), P85(85%), P90(90%),
P95(95%)
Unit: %
Actual Value Range: P00, P05, P10, P15, P20, P25,P30, P40, P50, P60, P70, P75, P80, P85, P90, P95
Default Value: P95(95%)
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
76
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 82/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
Special
ACBarF
orCsfb
MOD
CELLA
CBAR
LST
CELLA
CBAR
LBFD-0
02009 /
TDLBF
D-00200
9
Broadca
st of
system
informat
ion
Meaning:
Indicates whether CS fallback (CSFB) services
initiated by UEs of AC 11 to AC 15 are granted
access.
AC11BARSTATE: If this option is selected, the CSFB
services initiated by UEs of AC 11 in idle mode are
barred.
AC12BARSTATE: If this option is selected, the CSFB
services initiated by UEs of AC 12 in idle mode are
barred.
AC13BARSTATE: If this option is selected, the CSFBservices initiated by UEs of AC 13 in idle mode are
barred.
AC14BARSTATE: If this option is selected, the CSFB
services initiated by UEs of AC 14 in idle mode are
barred.
AC15BARSTATE: If this option is selected, the CSFB
services initiated by UEs of AC 15 in idle mode are
barred.
GUI Value Range:
AC11BARSTATE(AC11BARSTATE),AC12BARSTATE(AC12BARSTATE),
AC13BARSTATE(AC13BARSTATE),
AC14BARSTATE(AC14BARSTATE),
AC15BARSTATE(AC15BARSTATE)
Unit: None
Actual Value Range: AC11BARSTATE,
AC12BARSTATE, AC13BARSTATE,
AC14BARSTATE, AC15BARSTATE
Default Value: AC11BARSTATE:Permit,
AC12BARSTATE:Permit, AC13BARSTATE:Permit,
AC14BARSTATE:Permit, AC15BARSTATE:Permit
CellDyn
AcBarA
lgoPara
DynAcB
arStatPe
riod
MOD
CELLD
YNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
70207 /
TDLOF
D-07020
7
Intellige
nt
Access
Class
Control
Meaning: Indicates the statistic period of dynamic
access class (AC) barring in a cell, during which the
proportion of time that the cell is in the congestion
state is exported.
GUI Value Range: 10~60
Unit: s
Actual Value Range: 10~60
Default Value: 20
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
77
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 83/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellDyn
AcBarA
lgoPara
DynAcB
arTrigge
rThd
MOD
CELLD
YNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
70207 /
TDLOF
D-07020
7
Intellige
nt
Access
Class
Control
Meaning: Indicates the threshold for triggering
dynamic access class (AC) barring in the cell. This
threshold specifies the proportion of time that the cell
is in the congestion state. If the proportion of time that
the cell is in the congestion state is greater than or
equal to this parameter value within a statistic period
(specified by the DynAcBarStatPeriod parameter), the
conditions for triggering dynamic AC barring are met.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 100
CellDyn
AcBarA
lgoPara
DynAcB
arCancel
Thd
MOD
CELLD
YNACB
ARALG
OPARA
LST
CELLD
YNACB
ARALG
OPARA
LOFD-0
70207 /
TDLOF
D-07020
7
Intellige
nt
Access
Class
Control
Meaning: Indicates the threshold for canceling
dynamic access class (AC) barring in the cell. This
threshold specifies the proportion of time that the cell
is in the congestion state. If the proportion of time that
the cell is in the congestion state is less than or equal
to this parameter value within a statistic period
(specified by the DynAcBarStatPeriod parameter), the
conditions for canceling dynamic AC barring are met.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 80
CellAlg
oSwitch
LocalCe
llId
DSP
CELLU
LCAMC
CLUST
ER
LST
CELLA
LGOSW
ITCH
MOD
CELLA
LGOSW
ITCH
None None Meaning: Indicates the local ID of the cell. It uniquely
identifies a cell within a BS.
GUI Value Range: 0~255
Unit: None
Actual Value Range: 0~255
Default Value: None
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
78
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 84/90
MO Parameter ID
MMLCommand
FeatureID
FeatureName
Description
CellAcB
ar
LocalCe
llId
LST
CELLA
CBAR
MOD
CELLA
CBAR
None None Meaning: Indicates the local ID of the cell. It uniquely
identifies a cell within a BS.
GUI Value Range: 0~255
Unit: None
Actual Value Range: 0~255
Default Value: None
CellDyn
AcBarA
lgoPara
LocalCe
llId
LST
CELLD
YNACB
ARALG
OPARAMOD
CELLD
YNACB
ARALG
OPARA
None None Meaning: Indicates the local cell ID. It uniquely
identifies a cell within an eNodeB.
GUI Value Range: 0~255
Unit: None
Actual Value Range: 0~255
Default Value: None
eRAN
Access Class Control Feature Parameter Description 7 Parameters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
79
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 85/90
8 Counters
Table 8-1 Counters
Counter ID Counter Name CounterDescription
Feature ID Feature Name
1526728217 L.RRC.ConnReq.At
t.Emc
Number of RRC
connection setup
attempts with a
cause value of
emergency
Multi-mode: None
GSM: None
UMTS: None
LTE:
LBFD-002007
TDLBFD-002007
RRC Connection
Management
RRC Connection
Management
1526728220 L.RRC.ConnReq.Att.MoSig
Number of RRCconnection setup
attempts with a
cause value of mo-
Signalling
Multi-mode: NoneGSM: None
UMTS: None
LTE:
LBFD-002007
TDLBFD-002007
RRC ConnectionManagement
RRC Connection
Management
1526728221 L.RRC.ConnReq.At
t.MoData
Number of RRC
connection setup
attempts with a
cause value of mo-
Data
Multi-mode: None
GSM: None
UMTS: None
LTE:LBFD-002007
TDLBFD-002007
RRC Connection
Management
RRC Connection
Management
eRAN
Access Class Control Feature Parameter Description 8 Counters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
80
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 86/90
Counter ID Counter Name CounterDescription
Feature ID Feature Name
1526728321 L.CSFB.PrepAtt Number of CSFB
indicators received
by the eNodeB
Multi-mode: None
GSM: NoneUMTS: None
LTE:
LOFD-001033
TDLOFD-001033
LOFD-001034
TDLOFD-001034
LOFD-001035
TDLOFD-001035
CS Fallback to
UTRAN
CS Fallback to
UTRAN
CS Fallback to
GERAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
CS Fallback to
CDMA2000 1xRTT
1526728489 L.RRC.ConnReq.M
sg.disc.FlowCtrl
Number of times
the RRC
Connection Request
message is
discarded due to
flow control
Multi-mode: None
GSM: None
UMTS: None
LTE:
LBFD-002007
TDLBFD-002007
RRC Connection
Management
RRC Connection
Management
1526728490 L.RRC.SetupFail.R
ej.FlowCtrl
Number of times
the eNodeB sends
an RRC Connection
Reject message tothe UE due to flow
control
Multi-mode: None
GSM: None
UMTS: NoneLTE:
LBFD-002007
TDLBFD-002007
RRC Connection
Management
RRC Connection
Management
1526729499 L.Dyn.ACBar.Trigg
er.Num
Number of times
that dynamic AC
Barring is triggered
Multi-mode: None
GSM: None
UMTS: None
LTE:
LOFD-070207
TDLOFD-080202
Intelligent Access
Class Control
Intelligent Access
Class Control
1526729500 L.Dyn.ACBar.Canc
el.Num
Number of times
that dynamic AC
Barring is cancelled
Multi-mode: None
GSM: None
UMTS: None
LTE:
LOFD-070207
TDLOFD-080202
Intelligent Access
Class Control
Intelligent Access
Class Control
eRAN
Access Class Control Feature Parameter Description 8 Counters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
81
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 87/90
Counter ID Counter Name CounterDescription
Feature ID Feature Name
1526729501 L.Dyn.ACBar.Adju
st.Num
Number of times
that parameters
related to dynamic
AC Barring are
adjusted
Multi-mode: None
GSM: NoneUMTS: None
LTE:
LOFD-070207
TDLOFD-080202
Intelligent Access
Class Control
Intelligent Access
Class Control
1526729502 L.Dyn.ACBar.Contr
ol.Dur
Control duration of
dynamic AC
Barring
Multi-mode: None
GSM: None
UMTS: None
LTE:
LOFD-070207TDLOFD-080202
Intelligent Access
Class Control
Intelligent Access
Class Control
1526736656 L.SSAC.Dyn.ACBa
r.Trigger.Num
Number of times
dynamic SSAC is
triggered
Multi-mode: None
GSM: None
UMTS: None
LTE:
LBFD-002009
TDLBFD-002009
LOFD-008002
TDLOFD-081222LOFD-070207
Broadcast of system
information
Broadcast of system
information
Dynamic Service-
Specific Access
Control
Dynamic Service-
specific AcccessControl
Intelligent Access
Class Control
1526736657 L.SSAC.Dyn.ACBa
r.Adjust.Num
Number of times
parameters related
to dynamic SSAC
are adjusted
Multi-mode: None
GSM: None
UMTS: None
LTE:
LBFD-002009
TDLBFD-002009
LOFD-008002
TDLOFD-081222
LOFD-070207
Broadcast of system
information
Broadcast of system
information
Dynamic Service-
Specific Access
ControlDynamic Service-
specific Acccess
Control
Intelligent Access
Class Control
eRAN
Access Class Control Feature Parameter Description 8 Counters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
82
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 88/90
Counter ID Counter Name CounterDescription
Feature ID Feature Name
1526736658 L.SSAC.Dyn.ACBa
r.Cancel.Num
Number of times
dynamic SSAC is
canceled
Multi-mode: None
GSM: NoneUMTS: None
LTE:
LBFD-002009
TDLBFD-002009
LOFD-008002
TDLOFD-081222
LOFD-070207
Broadcast of system
information
Broadcast of system
information
Dynamic Service-
Specific Access
Control
Dynamic Service-
specific Acccess
Control
Intelligent Access
Class Control
1526736659 L.SSAC.Dyn.ACBa
r.Control.Dur
Duration of
dynamic SSAC
Multi-mode: None
GSM: None
UMTS: None
LTE:
LBFD-002009
TDLBFD-002009
LOFD-008002
TDLOFD-081222
LOFD-070207
Broadcast of system
information
Broadcast of system
information
Dynamic Service-
Specific Access
Control
Dynamic Service-
specific Acccess
Control
Intelligent AccessClass Control
1593835633 VS.BBUBoard.CP
ULoad.Mean
Average Board
CPU Usage
Multi-mode:
MRFD-210302
GSM:
GBFD-111202
UMTS: None
LTE:
LBFD-004009
TDLBFD-004009
Performance
Management
O&M of BTS
Real-time
Monitoring of
System Running
Information
Real-time
Monitoring of
System Running
Information
eRAN
Access Class Control Feature Parameter Description 8 Counters
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
83
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 89/90
9 Glossary
For the acronyms, abbreviations, terms, and definitions, see Glossary.
eRAN
Access Class Control Feature Parameter Description 9 Glossary
Issue 03 (2015-11-03) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
84
7/25/2019 Access Class Control(ERAN8.1_03)
http://slidepdf.com/reader/full/access-class-controleran8103 90/90
10 Reference Documents
1. 3GPP TS 36.331, " Radio Resource Control (RRC)"
2. 3GPP TS 24.301, "Non-Access-Stratum (NAS) protocol for Evolved Packet System (EPS);
Stage 3"
3. 3GPP TS 22.011, "Service accessibility"
4. 3GPP TS 23.122, "Non-Access-Stratum (NAS) functions related to Mobile Station (MS) in
idle mode"
eRAN
Access Class Control Feature Parameter Description 10 Reference Documents