accessories for solenoid valves ab 11 enfig. 7: adapter plate to mount a type 3967 solenoid valve on...
TRANSCRIPT
![Page 1: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/1.jpg)
AB 11 EN
Tran
slatio
n of
orig
inal
instr
uctio
ns
Edition December 2017
Adapter Plates, Double-axial Adapters and Restrictor Plates as Well as Special Constructions for Solenoid Valves
Accessories for Solenoid Valves
![Page 2: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/2.jpg)
2 AB 11 EN
The mounting and operating instructions for the devices are included in the scope of delivery. The latest documentation is available on our website at www.samson.de > Service & Support > Downloads > Documentation.
Definition of signal words
Hazardous situations which, if not avoided, will result in death or serious injury
Hazardous situations which, if not avoided, could result in death or serious injury
Property damage message or malfunction
Additional information
Recommended action
DANGER!
WARNING!
NOTICE!
Note
Tip
![Page 3: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/3.jpg)
Contents
AB 11 EN 3
1 Adapter plates ..............................................................................................41.1 Distance plate with NAMUR interface ¼ on rotary actuators ¼ .........................41.2 Distance plate with NAMUR interface ½ on rotary actuators ½ .........................61.3 Sealing plate with extended NAMUR interface ¼ on rotary actuators ¼ ............81.4 Adapter plate with NAMUR interface ¼ on rotary actuators ½ ........................101.5 Adapter plate with NAMUR interface ½ on rotary actuators ¼ ........................121.6 Adapter plate with NAMUR interface ¼ for external connection on rotary
actuators ¼ .................................................................................................141.7 Adapter plate NAMUR interface ½ on threaded connection ½ ........................161.8 Adapter plate with NAMUR interface ¼ on NAMUR rib .................................181.9 Adapter plate with NAMUR interface ¼ on NAMUR rib .................................201.10 Adapter plate with NAMUR interface ½ on NAMUR rib .................................221.11 Adapter plate with NAMUR interface ½ on NAMUR rib .................................242 Double-axial adapters .................................................................................262.1 Double-axial adapter 90° with NAMUR interface ¼ on rotary actuators ¼ ......262.2 Double-axial adapter 270° with NAMUR interface ¼ on rotary actuators ¼ ....282.3 Double-axial adapter 180° with NAMUR interface ¼ on rotary actuators ¼ ....302.4 Double-axial adapter 90° with NAMUR interface ½ on rotary actuators ½ ......322.5 Double-axial adapter 90° with NAMUR interface ½ on rotary actuators ½ ......343 Restrictor plates ...........................................................................................363.1 Exhaust air restrictor with NAMUR interface ¼ on rotary actuators ¼ ..............363.2 Supply air restrictor with NAMUR interface ¼ on rotary actuators ¼ ...............383.3 Double exhaust air restrictor with NAMUR interface ¼ on rotary actuators ¼ ...403.4 Universal restrictor with NAMUR interface ¼ on rotary actuators ¼ .................424 Special constructions ...................................................................................444.1 Emergency supply with NAMUR interface ¼ on rotary actuators ¼ .................444.2 Emergency venting with NAMUR interface ¼ on rotary actuators ¼ ................464.3 Emergency supply with NAMUR interface ½ on rotary actuators ½ .................484.4 Emergency venting with NAMUR interface ½ on rotary actuators ½ ................504.5 Adapter plate for four NAMUR interfaces ¼ on threaded connection ¼ ...........52
![Page 4: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/4.jpg)
4 AB 11 EN
Contents
4.6 Adapter plate (closed-circuit principle) ...........................................................544.7 Adapter plate (open-circuit principle) ............................................................56
![Page 5: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/5.jpg)
AB 11 EN 5
![Page 6: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/6.jpg)
6 AB 11 EN
Adapter plates
1 Adapter plates
1.1 Distance plate with NAMUR interface ¼ on rotary actuators ¼Distance plate made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 1400-9741
Stainless steel 1.4404, G thread 1402-0234
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The distance plate is mounted between the actuator with NAMUR interface according to VDI/VDE 3845 and pilot valve. Additional space is gained by using the distance plate. As a result, it is possible to also mount pilot valves whose shape prevents them being flush-mounted directly at the NAMUR interface of the rotary actuator.Refer to Fig. 1
![Page 7: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/7.jpg)
AB 11 EN 7
Adapter plates
On the valve side On the actuator side
Dimensions (in mm)
Fig. 1: Distance plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 8: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/8.jpg)
8 AB 11 EN
Adapter plates
1.2 Distance plate with NAMUR interface ½ on rotary actuators ½Distance plate made of aluminum (powder coated), for pilot valves with NAMUR interface according to VDI/VDE 3845 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 1400-9743
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The distance plate is mounted between the actuator with NAMUR interface according to VDI/VDE 3845 and pilot valve. Additional space is gained by using the distance plate. As a result, it is possible to also mount pilot valves whose shape prevents them being flush-mounted directly at the NAMUR interface of the rotary actuator.Refer to Fig. 2
![Page 9: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/9.jpg)
AB 11 EN 9
Adapter plates
On the valve side On the actuator side
Dimensions (in mm)
Fig. 2: Distance plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 10: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/10.jpg)
10 AB 11 EN
Adapter plates
1.3 Sealing plate with extended NAMUR interface ¼ on rotary actuators ¼
Sealing plate made of aluminum (powder coated), for pilot valves with NAMUR interface according to VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1402-1480
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The sealing plate is mounted between the actuator with NAMUR interface according to VDI/VDE 3845 and pilot valve. The sealing plate is used to mount pilot valves with an extended NAMUR interface according to VDI/VDE 3847 onto an actuator whose facing is too small to seal the pilot air ducts 1 and 9 of the extended NAMUR interface.Refer to Fig. 3
![Page 11: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/11.jpg)
AB 11 EN 11
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 3: Sealing plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 12: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/12.jpg)
12 AB 11 EN
Adapter plates
1.4 Adapter plate with NAMUR interface ¼ on rotary actuators ½Adapter plate made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1380-1652
Stainless steel 1.4404 1380-1797
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The adapter plate is mounted between the actuator with NAMUR interface according to VDI/VDE 3845 and pilot valve. The adapter plate is used to mount pilot valves with a NAMUR interface with ¼-size thread to rotary actuators with ½-size thread.Refer to Fig. 4
![Page 13: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/13.jpg)
AB 11 EN 13
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 4: Adapter plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 14: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/14.jpg)
14 AB 11 EN
Adapter plates
1.5 Adapter plate with NAMUR interface ½ on rotary actuators ¼Adapter plate made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1380-1795
Stainless steel 1.4404 1380-1796
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The adapter plate is mounted between the actuator with NAMUR interface according to VDI/VDE 3845 and pilot valve. The adapter plate is used to mount pilot valves with a NAMUR interface with ½-size thread to rotary actuators with ¼-size thread.Refer to Fig. 5
![Page 15: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/15.jpg)
AB 11 EN 15
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 5: Adapter plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 16: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/16.jpg)
16 AB 11 EN
Adapter plates
1.6 Adapter plate with NAMUR interface ¼ for external connection on rotary actuators ¼
Adapter plate with threaded connections, made of aluminum (powder coated)/stainless steel, for pilot valves with extended NAMUR interface according to VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G ¼ 1402-0695
Aluminum, ¼ NPT 1402-0697
Stainless steel 1.4404, G ¼ 1402-0696
Stainless steel 1.4404, ¼ NPT 1402-0698
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847The adapter plate is mounted between the actuator with NAMUR interface according to VDI/VDE 3845 and pilot valve. The supply air is connected to port 1 of the adapter plate, which is supplied to the port 1 of the pilot valve through the extended NAMUR interface according to VDI/VDE 3847. An external air supply can be used at port 9 of the adapter plate for pilot-operated valves. The port 3 of the adapter plate can be used for an optional exhaust air feedback of other valve accessories.
If the pilot valve does not have a separate venting, install a venting plug in the pipe connection at port 3.
The adapter plate allows the pilot valve to be exchanged without making any changes to the air supply lines.Refer to Fig. 6
Note
![Page 17: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/17.jpg)
AB 11 EN 17
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 6: Adapter plate with external connection with Type 3967 Solenoid Valve on a rotary actuator
![Page 18: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/18.jpg)
18 AB 11 EN
Adapter plates
1.7 Adapter plate NAMUR interface ½ on threaded connection ½Adapter plate with threaded connections, made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 on threaded connection
Ordering no.: Aluminum, G ½ 1402-1833
Aluminum, ½ NPT 1402-1834
Stainless steel 1.4404, G ½ 1402-1835
Stainless steel 1.4404, ½ NPT 1402-1836
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The adapter plate is mounted between the actuator with threaded connection and the pilot valve. The adapter plate is used to fit pilot valves with a NAMUR interface with ½-size with a connecting thread and integrate them into a pipe connection.Refer to Fig. 7
![Page 19: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/19.jpg)
AB 11 EN 19
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator
![Page 20: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/20.jpg)
20 AB 11 EN
Adapter plates
1.8 Adapter plate with NAMUR interface ¼ on NAMUR ribAdapter plate with threaded connections, made of aluminum (powder coated)/stainless steel, for pilot valves with extended NAMUR interface according to VDI/VDE 3847 on actuators with NAMUR interface according to IEC 60534-6 including fastening screw.
Ordering no.: Aluminum, G ¼ 1400-9598
Aluminum, ¼ NPT 1400-9599
Stainless steel 1.4404, G ¼ 1400-9600
Stainless steel 1.4404, ¼ NPT 1400-9601
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The adapter plate is mounted between the actuator and pilot valve. The adapter plate is used to mount the pilot valve to the NAMUR rib according to IEC 60534-6 and to integrate it into the pipeline using the connecting thread. The supply air is connected to port 1 of the adapter plate, which is supplied to the port 1 of the pilot valve through the extended NAMUR interface according to VDI/VDE 3847. An external air supply can be used at port 9 of the adapter plate for pilot-operated valves. The port 3 of the adapter plate can be used for an optional exhaust air feedback of other valve accessories.
If the pilot valve does not have a separate venting, install a venting plug in the pipe connection at port 3.
The adapter plate allows the pilot valve to be exchanged without mak-ing any changes to the air supply lines.Refer to Fig. 8
Note
![Page 21: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/21.jpg)
AB 11 EN 21
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 8: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator
![Page 22: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/22.jpg)
22 AB 11 EN
Adapter plates
1.9 Adapter plate with NAMUR interface ¼ on NAMUR ribAdapter plate with threaded connections, made of aluminum (powder coated), for pilot valves with NAMUR interface according to VDI/VDE 3845 on actuators with NAMUR interface according to IEC 60534-6 including fastening screw.
Ordering no.: Aluminum, G ¼ 1400-6751
Aluminum, ¼ NPT 1400-9924
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845The adapter plate is mounted between the actuator and pilot valve. The adapter plate is used to mount pilot valves to the NAMUR rib according to IEC 60534-6 and to connect it to the pipeline using the connecting thread.Refer to Fig. 9
![Page 23: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/23.jpg)
AB 11 EN 23
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 9: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator
![Page 24: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/24.jpg)
24 AB 11 EN
Adapter plates
1.10 Adapter plate with NAMUR interface ½ on NAMUR ribAdapter plate with threaded connections, made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 on actuators with NAMUR interface according to IEC 60534-6 including fastening screw.
Ordering no.: Aluminum, G ½ 1402-0827
Aluminum, ½ NPT 1402-0829
Stainless steel 1.4404, G ½ 1402-0828
Stainless steel 1.4404, ½ NPT 1402-0830
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The adapter plate is mounted between the actuator and pilot valve. The adapter plate is used to mount the pilot valve to the NAMUR rib according to IEC 60534-6 and to integrate it into the pipeline using the connecting thread.Refer to Fig. 10
![Page 25: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/25.jpg)
AB 11 EN 25
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 10:Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator
![Page 26: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/26.jpg)
26 AB 11 EN
Adapter plates
1.11 Adapter plate with NAMUR interface ½ on NAMUR ribAdapter plate with threaded connections, made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 on actuators with NAMUR interface according to IEC 60534-6 including fastening screw.
Ordering no.: Aluminum, G ½ 1402-1461
Stainless steel 1.4404, G ½ 1402-1462
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The adapter plate is mounted between the actuator and pilot valve. The adapter plate is used to mount the pilot valve to the NAMUR rib according to IEC 60534-6 and to integrate it into the pipeline using the connecting thread.The adapter plate has additional ports and can be used for an optional exhaust air feedback of other valve accessories.Refer to Fig. 11
![Page 27: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/27.jpg)
AB 11 EN 27
Adapter plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 11:Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator
![Page 28: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/28.jpg)
28 AB 11 EN
Double-axial adapters
2 Double-axial adapters
2.1 Double-axial adapter 90° with NAMUR interface ¼ on rotary actuators ¼
Double-axial adapter made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1993-0089
Stainless steel 1.4404 1993-0219
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The double-axial adapter is mounted between the actuator and pilot valve. The double-axial adapter is used to optimize the installation position of the pilot valve by turning it by 90°. The pilot air ducts 1 and 9 of the extended NAMUR interface ¼ according to VDI/VDE 3847 are also diverted by 90°.Refer to Fig. 12
![Page 29: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/29.jpg)
AB 11 EN 29
Double-axial adapters
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 12:Double-axial adapter to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 30: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/30.jpg)
30 AB 11 EN
Double-axial adapters
2.2 Double-axial adapter 270° with NAMUR interface ¼ on rotary actuators ¼
Double-axial adapter made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1993-0220
Stainless steel 1.4404 1993-0221
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The double-axial adapter is mounted between the actuator and pilot valve. The double-axial adapter is used to optimize the installation position of the pilot valve by turning it by 270°. The pilot air ducts 1 and 9 of the extended NAMUR interface ¼ according to VDI/VDE 3847 are also diverted by 270°.Refer to Fig. 13
![Page 31: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/31.jpg)
AB 11 EN 31
Double-axial adapters
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 13:Double-axial adapter to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 32: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/32.jpg)
32 AB 11 EN
Double-axial adapters
2.3 Double-axial adapter 180° with NAMUR interface ¼ on rotary actuators ¼
Double-axial adapter made of aluminum (powder coated), for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1402-0280
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The double-axial adapter is mounted between the actuator and pilot valve. The double-axial adapter is used to optimize the installation position of the pilot valve by turning it by 180°. The pilot air ducts 1 and 9 of the extended NAMUR interface ¼ according to VDI/VDE 3847 are also diverted by 180°.Refer to Fig. 14
![Page 33: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/33.jpg)
AB 11 EN 33
Double-axial adapters
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 14:Double-axial adapter to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 34: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/34.jpg)
34 AB 11 EN
Double-axial adapters
2.4 Double-axial adapter 90° with NAMUR interface ½ on rotary actuators ½
Double-axial adapter made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1402-0602
Stainless steel 1.4404 1402-0603
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The double-axial adapter is mounted between the actuator and pilot valve. The double-axial adapter is used to optimize the installation position of the pilot valve by turning it by 90°.Refer to Fig. 15
![Page 35: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/35.jpg)
AB 11 EN 35
Double-axial adapters
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 15:Double-axial adapter to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 36: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/36.jpg)
36 AB 11 EN
Double-axial adapters
2.5 Double-axial adapter 90° with NAMUR interface ½ on rotary actuators ½
Double-axial adapter made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 1402-1662
Stainless steel 1.4404, G thread 1402-1663
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The double-axial adapter is mounted between the actuator and pilot valve. The double-axial adapter is used to optimize the installation position of the pilot valve by turning it by 90°.The double-axial adapter has additional ports and can be used for an optional exhaust air feedback of other valve accessories.Refer to Fig. 16
![Page 37: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/37.jpg)
AB 11 EN 37
Double-axial adapters
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 16:Double-axial adapter to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 38: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/38.jpg)
38 AB 11 EN
Restrictor plates
3 Restrictor plates
3.1 Exhaust air restrictor with NAMUR interface ¼ on rotary actuators ¼
Restrictor plate for restricting the flow of exhaust air, made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1400-9602
Aluminum 1402-0141 1)
Stainless steel 1.4404 1402-0137
Stainless steel 1.4404 1402-0142 1)
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The restrictor plate is mounted between the actuator and pilot valve. The restrictor plate allows the closing time of the actuator to be adjusted by restricting the flow rate of the exhaust air within the range of KVS 0 to 0.28 (KVS 0.01 to 0.28 for restrictors marked with 1)).Adapter plates (see sections 1.8 and 1.9) can be added to this combi-nation to allow them to be used on linear actuators.Refer to Fig. 17
1) Suitable for use in safety-instrumented systems (SIL) according to IEC 61508 observing the require-ments in the Manufacturer's Declaration No. 1296 and Safety Manual u SH 3967-2
![Page 39: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/39.jpg)
AB 11 EN 39
Restrictor plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 17:Restrictor plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 40: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/40.jpg)
40 AB 11 EN
Restrictor plates
3.2 Supply air restrictor with NAMUR interface ¼ on rotary actuators ¼
Restrictor plate for restricting the flow of supply air, made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1400-9603
Aluminum 1402-0139 1)
Stainless steel 1.4404 1402-0136
Stainless steel 1.4404 1402-0140 1)
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The restrictor plate is mounted between the actuator and pilot valve. The restrictor plate allows the opening time of the actuator to be adjusted by restricting the flow rate of the supply air within the range of KVS 0 to 0.28 (KVS 0.01 to 0.28 for restrictors marked with 1)).
The reduction of the air supply may cause a stick-slip effect in the actua-tor.
Adapter plates (see sections 1.8 and 1.9) can be added to this combi-nation to allow them to be used on linear actuators.Refer to Fig. 18
1) Suitable for use in safety-instrumented systems (SIL) according to IEC 61508 observing the require-ments in the Manufacturer's Declaration No. 1296 and Safety Manual u SH 3967-2
Note
![Page 41: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/41.jpg)
AB 11 EN 41
Restrictor plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 18:Restrictor plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 42: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/42.jpg)
42 AB 11 EN
Restrictor plates
3.3 Double exhaust air restrictor with NAMUR interface ¼ on rotary actuators ¼
Restrictor plate for restricting the flows of exhaust air, made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1400-9604
Aluminum 1402-0143 1)
Stainless steel 1.4404 1402-0138
Stainless steel 1.4404 1402-0144 1)
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The restrictor plate is mounted between the actuator and pilot valve. The restrictor plate allows the opening and closing time of the actuator to be adjusted by restricting the flow rate of the exhaust air within the range of KVS 0 to 0.28 (KVS 0.01 to 0.28 for restrictors marked with 1)).Adapter plates (see sections 1.8 and 1.9) can be added to this combi-nation to allow them to be used on linear actuators.Refer to Fig. 19
1) Suitable for use in safety-instrumented systems (SIL) according to IEC 61508 observing the require-ments in the Manufacturer's Declaration No. 1296 and Safety Manual u SH 3967-2
![Page 43: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/43.jpg)
AB 11 EN 43
Restrictor plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 19:Restrictor plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 44: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/44.jpg)
44 AB 11 EN
Restrictor plates
3.4 Universal restrictor with NAMUR interface ¼ on rotary actuators ¼
Restrictor plate for restricting the flow of exhaust air based on the pressure, made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3845 or VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum 1402-0149 1)
Stainless steel 1.4404 1402-0150 1)
Use: For pilot valves with NAMUR interface ¼ according to VDI/VDE 3845 or extended NAMUR interface ¼ according to VDI/VDE 3847.The restrictor plate is mounted between the actuator and pilot valve. The restrictor plate allows the opening and closing times of the actuator to be adjusted by restricting the flow rate of the exhaust air within the range of KVS 0.01 to 0.28. It is possible to change the actuator chamber which is to be restricted by turning the plate by 180°.Adapter plates (see sections 1.8 and 1.9) can be added to this combi-nation to allow them to be used on linear actuators.Refer to Fig. 20
1) Suitable for use in safety-instrumented systems (SIL) according to IEC 61508 observing the require-ments in the Manufacturer's Declaration No. 1296 and Safety Manual u SH 3967-2
![Page 45: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/45.jpg)
AB 11 EN 45
Restrictor plates
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 20:Restrictor plate to mount a Type 3967 Solenoid Valve on a rotary actuator
![Page 46: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/46.jpg)
46 AB 11 EN
Special constructions
4 Special constructions
4.1 Emergency supply with NAMUR interface ¼ on rotary actuators ¼
Adapter plate made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 1402-0007
Aluminum, NPT thread 1402-0009
Stainless steel 1.4404, G thread 1402-0008
Stainless steel 1.4404, NPT thread 1402-0010
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The adapter plate is mounted between the actuator and pilot valve. The adapter plate is used to increase the availability through parallel connection of two pilot valves. The pilot valves are mounted to the left and right on the extended NAMUR interfaces according to VDI/VDE 3847. The adapter plate is fastened to the actuator using a third NAMUR interface according to VDI/VDE 3845.
The pilot valve at the connecting surface V1 of the adapter plate must have a venting.The pilot valve's venting at the connecting surface V2 of the adapter plate must be sealed.Refer to TV-SK 9932 for a detailed mounting description.
Adapter plates (see sections 1.8 and 1.9) can be added to this combi-nation to allow them to be used on linear actuators.Refer to Fig. 21
Note
![Page 47: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/47.jpg)
AB 11 EN 47
Special constructions
On the actuator side Supply airOn the valve side (both sides)
Dimensions (in mm)
Fig. 21:Adapter plate to mount a Type 3967 and Type 3963 Solenoid Valve on a rotary actuator
![Page 48: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/48.jpg)
48 AB 11 EN
Special constructions
4.2 Emergency venting with NAMUR interface ¼ on rotary actua-tors ¼
Adapter plate made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 1402-0011
Aluminum, NPT thread 1402-0013
Stainless steel 1.4404, G thread 1402-0012
Stainless steel 1.4404, NPT thread 1402-0014
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The adapter plate is mounted between the actuator and pilot valve. The adapter plate is used to increase the safety through series connection of two pilot valves. The pilot valves are mounted to the left and right on the extended NAMUR interfaces according to VDI/VDE 3847. The adapter plate is fastened to the actuator using a third NAMUR interface according to VDI/VDE 3845.
The pilot valves at connecting surfaces V1 and V2 of the adapter plate must have a venting.Refer to TV-SK 9932 for a detailed mounting description.
Adapter plates (see sections 1.8 and 1.9) can be added to this combi-nation to allow them to be used on linear actuators.Refer to Fig. 22
Note
![Page 49: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/49.jpg)
AB 11 EN 49
Special constructions
On the actuator side Supply airOn the valve side (both sides)
Dimensions (in mm)
Fig. 22:Adapter plate to mount two Type 3967 Solenoid Valves on a rotary actuator
![Page 50: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/50.jpg)
50 AB 11 EN
Special constructions
4.3 Emergency supply with NAMUR interface ½ on rotary actuators ½
Pneumatic booster valve made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3847 on rotary actuators with NAMUR interface according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 3756: configuration ID 5737887 1)
Aluminum, NPT thread 3756: configuration ID 5800280 1)
Stainless steel 1.4404, G thread 3756: configuration ID 5800281 1)
Stainless steel 1.4404, NPT thread
3756: configuration ID 5800283 1)
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The booster valve is mounted between the actuator and pilot valve. The booster valve is used to increase the availability through parallel connection of two pilot valves and raises their flow coefficient to KVS 1.9. The pilot valves are mounted to the left and right on the extended NAMUR interfaces according to VDI/VDE 3847. The booster valve is fastened to the actuator using a third NAMUR interface according to VDI/VDE 3845.
The pilot valves at connecting surfaces V1 and V2 of the booster valve must have a venting.
Adapter plates (see sections 1.10 and 1.11) can be added to this com-bination to allow them to be used on linear actuators.Refer to Fig. 23
1) Refer to the referenced documents for Type 3756 Pneumatic Booster Valve for more details and other versions.
Note
![Page 51: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/51.jpg)
AB 11 EN 51
Special constructions
On the actuator side Supply air
Dimensions (in mm)
Fig. 23:Booster valve to mount two Type 3967 Solenoid Valves on a rotary actuator
![Page 52: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/52.jpg)
52 AB 11 EN
Special constructions
4.4 Emergency venting with NAMUR interface ½ on rotary actuators ½
Pneumatic booster valve made of aluminum (powder coated)/stainless steel, for pilot valves with NAMUR interface according to VDI/VDE 3847 on rotary actuators with NAMUR inter-face according to VDI/VDE 3845 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 3756: configuration ID 5711460 1)
Aluminum, NPT thread 3756: configuration ID 5711464 1)
Stainless steel 1.4404, G thread 3756: configuration ID 5711730 1)
Stainless steel 1.4404, NPT thread
3756: configuration ID 5711726 1)
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The booster valve is mounted between the actuator and pilot valve. The booster valve is used to increase the safety through series connection of two pilot valves and to raise their KVS to 1.9. The pilot valves are mounted to the left and right on the extended NAMUR interfaces according to VDI/VDE 3847. The booster valve is fastened to the actuator using a third NAMUR interface according to VDI/VDE 3845.
The pilot valves at connecting surfaces V1 and V2 of the booster valve must have a venting.
Adapter plates (see sections 1.10 and 1.11) can be added to this com-bination to allow them to be used on linear actuators.Refer to Fig. 24
1) Refer to the referenced documents for Type 3756 Pneumatic Booster Valve for more details and other versions.
Note
![Page 53: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/53.jpg)
AB 11 EN 53
Special constructions
On the actuator side Supply air
Dimensions (in mm)
Fig. 24:Booster valve to mount two Type 3967 Solenoid Valves on a rotary actuator
![Page 54: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/54.jpg)
54 AB 11 EN
Special constructions
4.5 Adapter plate for four NAMUR interfaces ¼ on threaded connection ¼
Adapter plate with threaded connections, made of aluminum (powder coated), for pilot valves with NAMUR interface according to VDI/VDE 3847 on threaded connection including fastening screws.
Ordering no.: Aluminum, G thread 1402-0438
Accessories: Blank plate 1402-1290
Screw plug 0070-0858
O-ring 14x1.5 8421-0070
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The adapter plate is mounted between the actuator and pilot valve. The adapter plate is used to supply up to four pilot valves simultaneously over a supply air connection. The pilot valves are mounted on the extended NAMUR interfaces according to VDI/VDE 3847 and can be included in the pipe hook-up using a connecting thread. Any connecting spaces not used can be sealed using the appropriate accessories.Refer to Fig. 25
![Page 55: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/55.jpg)
AB 11 EN 55
Special constructions
Connections for hook-up
On the valve side
Dimensions (in mm)
Fig. 25:Adapter plate
![Page 56: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/56.jpg)
56 AB 11 EN
Special constructions
4.6 Adapter plate (closed-circuit principle)Adapter plate made of aluminum (powder coated), for pilot valves with NAMUR interface according to VDI/VDE 3847 on mounting blocks for positioners with NAMUR interface according to VDI/VDE 3847 including fastening screws and gaskets.
Ordering no.: Aluminum 1402-1553
Use: For pilot valves with extended NAMUR interface ¼ according to VDI/VDE 3847.The adapter plate is mounted between the mounting block and pilot valve. The adapter plate is used to implement the closed-circuit principle. The adapter plate connects port 9 of the mounting block to the port 9 and port 3 of the pilot valve. As a result, closed-loop control of the actuator takes place when the pilot valve is energized. When the pilot valve is de-energized, the actuator is filled with air.
This function is only provided when pilot-operated pilot valves are used.The pilot valve must have a sealable venting port.
Refer to Fig. 26
Note
![Page 57: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/57.jpg)
AB 11 EN 57
Special constructions
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 26:Adapter plate
![Page 58: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/58.jpg)
58 AB 11 EN
Special constructions
4.7 Adapter plate (open-circuit principle)Adapter plate made of aluminum (powder coated), for pilot valves with NAMUR interface according to VDI/VDE 3845 on mounting blocks for positioners with NAMUR interface ac-cording to VDI/VDE 3847 including fastening screws and gaskets.
Ordering no.: Aluminum, G thread 1402-0894
Use: For pilot valves with NAMUR interface ½ according to VDI/VDE 3845.The adapter plate is mounted between the mounting block and pilot valve. The adapter plate is used to implement the open-circuit principle. The adapter plate allows port 9 of the mounting block to be connected to the port 1 of the pilot valve over an external pipe connection. At the same time, port 2 and port 3 of the mounting block are turned in the adapter plate. As a result, closed-loop control of the actuator takes place when the pilot valve is de-energized. When the pilot valve is energized, the actuator is filled with air.
The pilot valve must have a sealable venting port.
An additional option of the adapter plate involves the reversal of the direction of action from NC to NO with pilot-operated pilot valves with external air supply or directly controlled pilot valves. The external pipe connection must be connected to port 9 of a pilot-operated pilot valve. The connection for the external pipe connection of directly controlled pilot valves must be sealed.Refer to Fig. 27
Note
![Page 59: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/59.jpg)
AB 11 EN 59
Special constructions
On the actuator sideOn the valve side
Dimensions (in mm)
Fig. 27:Adapter plate
![Page 60: Accessories for Solenoid Valves AB 11 ENFig. 7: Adapter plate to mount a Type 3967 Solenoid Valve on a linear actuator. 20 AB 11 EN Adapter plates 1.8 Adapter plate with NAMUR interface](https://reader034.vdocuments.net/reader034/viewer/2022042017/5e75482bb6542b41104dfb9d/html5/thumbnails/60.jpg)
SAMSON AG · MESS- UND REGELTECHNIKWeismüllerstraße 3 · 60314 Frankfurt am Main, GermanyPhone: +49 69 4009-0 · Fax: +49 69 [email protected] · www.samson.de AB 11 EN 20
18-0
3-19
· En
glish