Accessories Material Specification

1000.0000-Td-0701_rev0

Page 1 of 2

ACCESSORIES MATERIAL SPECIFICATION

Accessory Component Material Quality Standard Treatment Sketch

Fender Anchorage. Old Concrete

Bolt Nut “L” Washer

DIN-975 DIN-934

-

4.8 5

S275JR

EN-ISO 848-1 EN-ISO 848-2

-

HDG (1)

ISO 1461:2009

Bolt DIN -933 4.8 EN-ISO 848-1

Threaded Socket - S355JR EN 10025

Round - S355JR EN 10025

Fender Anchorage. New Concrete

Plate “L” Washer

- -

S275JR S275JR

EN 10025 -

HDG (1)

ISO 1461:2009

Chain Anchorage. Old Concrete U Round - S275J2 EN 10025

HDG (1)

ISO 1461:2009

U Round - S275J2 Chain Anchorage. New Concrete Plate - S275JR

EN 10025

HDG (1)

ISO 1461:2009

Plate - S275JR EN 10025

Bolt DIN-975 4.8 EN-ISO 848-1

Nut DIN-934 5 EN-ISO 848-2

Chain anchorage bracket

Washer DIN-125 BC -

HDG (1)

ISO 1461:2009

Round - S275J2 EN 10025

Plate - S275JR EN 10025 Tensor

Nut DIN-934 5 EN-ISO 848-2

HDG (1)

ISO 1461:2009

L Washer Plate - S275JR EN 10025

HDG (1)

ISO 1461:2009

Bolt DIN-933 4.8 EN-ISO 848-1

Nut DIN-934 5 EN-ISO 848-2 Fender Bolts

Plain Washer DIN-125 BC -

HDG (1)

ISO 1461:2009

Bolt DIN-933 4.8 EN-ISO 848-1

Nut DIN-934 5 EN-ISO 848-2 Polythene Botls

Plain Washer DIN-125 BC -

HDG (1)

ISO 1461:2009

Bolt DIN-931 4.8 EN-ISO 848-1

Nut DIN-934 5 EN-ISO 848-2 Chain bolts

Plain Washer DIN-125 BC -

HDG (1) ISO 1461:2009

Accessories Material Specification

1000.0000-Td-0701_rev0

Page 2 of 2

(1) GALVANIZING THICKNESS REQUIREMENT

Accessory Standard Applied Galvanizing Process Local

Thickness Required

Average Thickness Required

Fender Anchorages Thread Rod ISO 1461:2009 Not Centrifuged 70 µm 85 µm

Chain Anchorages U configuration ISO 1461:2009 Not Centrifuged 70 µm 85 µm

Chain Anchorages Bracket configuration ISO 1461:2009 Not Centrifuged 70 µm 85 µm

Tensors ISO 1461:2009 Not Centrifuged 70 µm 85 µm

Shackles ISO 1461:2009 Not Centrifuged 70 µm 85 µm

Chains ISO 1461:2009 Not Centrifuged 70 µm 85 µm

Shaft for cylindrical fenders ISO 1461:2009 Not Centrifuged 70 µm 85 µm

Fender anchorages ISO 1461:2009 Centrifuged 40 µm 50 µm

Bolts ISO 1461:2009 Centrifuged 40 µm 50 µm

Nuts ISO 1461:2009 Centrifuged 40 µm 50 µm

Plain Washers ISO 1461:2009 Centrifuged 45 µm 55 µm

L Washers ISO 1461:2009 Centrifuged 45 µm 55 µm

NOTE:

- Issue of 2.1 certificate according UNE-EN-ISO 10204. - Any other tests to consider, beyond those mentioned here, is optional at extra cost.

It is not allowed to reproduce, photocopy, scan or copy this document or part of this document without the previous written authorization of the manufacturer. Due to our politics of improvement and constant development, all the technical information of this document is subject to changes without previous notice. This document has been realized by the major care, nevertheless the manufacturer does not assume any responsibility of any mistake in this document

Accessory Component Material Quality Standard Treatment Sketch

Dee Shackle Standard Shackle

DIN 82101 A Type - HDG (1)

ISO 1461:2009

Chain Chain DIN-764 GRADO 2 Without stud link - HDG (1)

ISO 1461:2009

Shaft for cylindrical Fender Round - S355JR EN 10025 HDG (1)

ISO 1461:2009