acg altiled presentation en

8/3/2019 Acg Altiled Presentation En

http://slidepdf.com/reader/full/acg-altiled-presentation-en 1/22

ACG-AltiLEDLED High-Bay Industrial Lighting Fixture

ACG Elektronik Ltd.

www.acgelectronics.com



CONTENTS

ASSEMBLY

HOW MANY FIXTURES SHOULD I USE?

A RELIABLE & EFFICIENT LED LIGHTING FIXTURE

HOW MUCH WILL I SAVE?

ADVANTAGES OF LED LIGHTING




High efficiency (low power consumption)

* During the production of AltiLED7 100 lumens/watt, Philips Lumileds Luxeon Rebel LEDs are used.Efficiency of various light sources are shown in the below table:

Philips LumiledsLuxeon Rebel LED

tungsten incandescent 6-10

lumens/watt

(light output with1Watt energy

consumption)

halojen incandescent 16-22

compact fluorescent 30-60

linear fluorescent 46-95

gas discharge 55-125

LED 60-132




Long lifespan (>50.000 hours)

* Estimated lifespan of AltiLED is over 50.000 hours. According to the test report of Philips Lumileds,light output will decrease 7.3% at the end of 10.000 hours and 30% at the end of 54.000 hours.




High light usage (80%)

* For some light sources that are used in industrial lighting the bulb efficiency is quite high. But forconventional systems reflectors are used to direct the light to the illuminated surface. Most of the light isunused and scattered around in those systems. For LED lighting this is not the case, around 80% of lightis directed to the illuminated surface.




Superior light quality (CRI >70)

* AltiLED provide a high quality cool white (6500K) light. So that the colors are observed as they areunder sunlight. The flickering of light in gas discharge and fluorescent bulbs is totally prevented.




High lumen maintenance

* Lumen output of high intensity discharge lamps are decreasing rapidly after a few thousands of hoursof use. After 10.000 hours of operation the lumen output of most metal halide lamps decrease 30%,

while for high quality LEDs it is only 7%.




Even light distribution

* Conventional lighting fixtures cause higher/lower than required illuminated areas. The patenteddesign of AltiLED provides an even light distribution.

Conventional lighting fixtures AltiLED




Green product

* Using AltiLED will provide less energy use, less polution caused by power plantsand less CO2(carbon dioxide) emission to the atmosphere. Each AltiLED7 preventsemission of 8.7 tons of CO2, at the end of 50.000 hours of usage.

* Sodyum Sodium lamps, mercury lamps, fluorescent lamps and metal halidelamps all contain excess amounts of mercury, which causes pollution of water andsoil. Being a green product, AltiLED contains none of the restricted substances(lead, mercury, cadmium etc.) according to RoHS (Restriction of HazardousSubstances).



HOW MUCH WILL I SAVE?

SAVINGS CALCULATION

* AltiLED7 will provide significant energy and maintenance savings. You can calculate total savings andpayback time from the following link:

http://www.acgelectronics.com/index.php?page=altiled

BULB TYPETOTAL

CONSUMPTION1 YEAR

ENERGY COST

ANNUALMAINTENANCE

COST

6 YEAR ENERGYAND

MAINTENANCECOST

AltiLED7

(110W)

125W 146 USD - 877 USD

METAL HALIDE

(250W)310W 363 USD 39 USD 2,408 USD

SODIUM or METALHALIDE

(400W)

480W 561 USD 39 USD 3,600 USD

*300 days/year, 24 hours/day.






ELECTRONIC DESIGN

* LED properties are changing during the operation of the LED lighting system. To deal with thosedynamic properties, LED manufacturers strongly recommend “constant current drivers” . Otherwise thesystem will not be reliable.

* Low-quality LEDs not only diminishes the efficiency of the system, but also affect the light quality andsystem reliability. In AltiLED, Philips Lumileds’ highest bin LEDs are used.

* It is also important that the electronic componentsused in the constant current driver are high efficiencyand durable. In AltiLED there is a specially developedcircuit with an efficiency of 93%.

* AltiLED is CE tested and certified.




THERMAL DESIGN

* Efficiency and lifespan of LED lighting fixtures are adversely affected by heat. It must be assured thatcertain limits of LEDs are not reached. To provide that, significant attention must be payed for thermaldesign.

* For AltiLED a computer aided thermal simulation is done, and design is verified to have an 50.000hours of lifespan.




OPTICAL DESIGN

* One of the most important advantages of LED lighting fixtures is the high light usage capability.Instead of reflectors used in conventional lighting systems, high efficiency lenses are used in LED lightingsystems. Each module of AltiLED has a high efficiency lens (90%) to direct the light to the illuminatedarea. Despite the long distance between the fixture and the ground, light usage is as high as 80%.




Recommended lighting levels

* According to IESNA recommended lighting levels are as follows:

Orientation lights for short visits 50-100 lux

Working areas where visual tasks are only occasionally performed 100-200 lux

Warehouses, archives 150 lux

Working areas where high contrast visual tasks are performed 200-500 lux

Working areas where medium contrast visual tasks are performed 500-1000 lux

Working areas where low contrast visual tasks are performed 1000-2000 lux




How much of the light should be supplied by general lighting?

* Up to 200 lux is provided by general lighting, over 200 lux is provided by task lighting.

General lighting Task lighting




How many fixtures should be used?

* The illumination levels depending on the total number of fixtures is given in the table below. It mustalso be taken into account that at the end of 50.000 hours of usage, there will be a 30% decrease in thelight output. For that reason

instead of 150 lux, 200 lux

instead of 200 lux, 260 luxcan be selected.

PLACEMENT TOTAL NO OF FIXTURES ILLUMINATION

1 FIXTURE PER 8 METERS 16 115 LUX





ASSEMBLY

Power supply

* AltiLED works with 24V DC voltage input. A reliable, high efficiency power supply must be used and the

product shouldn’t be connected to 220/380V AC directly.



ASSEMBLY

Power supply connection diagrams

* According to the dimensions of the indoor place, 2, 3 or 4 pcs. fixtures can be powered with a singlepower supply. The connection diagrams section of the datasheet (in www.acgelectronics.com) must be

read carefully before designing the electrical system.



ASSEMBLY

Mechanical mounting

* Product is designed to be mounted by a chain or metal rope. Cable length is 1.0 meter. The net weight

of AltiLED7 is 5.1kgs.



MORE INFORMATION & CONTACT US

To get more information about AltiLED Series Industrial Lighting

Fixtures you can use the following links:

• Product datasheet (all the information about the product)http://www.acgelectronics.com/datasheets/acg_altiled_datasheet_1_03_en.pdf

• Assembly guidehttp://www.acgelectronics.com/datasheets/acg_assembly_guide_en.pdf

• Technical Informationhttp://www.acgelectronics.com/datasheets/acg_altiled_technical_information_en.pdf

To request for quotation or any other information:

• Inquiry formhttp://www.acgelectronics.com/index.php?page=teklif

http://www.acgelectronics.com/datasheets/acg_altiled_datasheet_1_03_en.pdf

http://www.acgelectronics.com/datasheets/acg_assembly_guide_en.pdf

http://www.acgelectronics.com/datasheets/acg_altiled_technical_information_en.pdf

http://www.acgelectronics.com/index.php?page=teklif

http://www.acgelectronics.com/index.php?page=teklif

http://www.acgelectronics.com/datasheets/acg_altiled_technical_information_en.pdf

http://www.acgelectronics.com/datasheets/acg_assembly_guide_en.pdf

http://www.acgelectronics.com/datasheets/acg_altiled_datasheet_1_03_en.pdf



ABOUT US

About Us

ACG Electronics is a provider of innovative LED Lighting products and services for theprivate, municipal and governmental sectors. The company established in 2005 atAnkara, Turkey. In 2009, with its well established expertise in the field of manufacturing,ACG Electronics chose to diversify in the field of Industrial Wide Area Lighting.

We recognize high implementation cost is a major resistance the industry faces, adapteda business model based on our team strength, that utilize the excellent talents and lowermanufacturing costs in Turkey to produce high quality, low cost innovative products andpass the savings onto our customers, to bring financially viable solutions to ourcustomers.

ACG Electronics exports its products to 34 countries (Germany, Austria, United Kingdom,The Netherlands, USA, France, Italy, Finland, Spain, Portugal, Sweden, Denmark,

Norway, Belgium, Luxemburg, Canada, Japan, Russia, Switzerland, Greece, Bulgaria,Romania, Hungary, Lithuania, Estonia, Iran, Poland, Brazil, Argentina, Mexico, HongKong, China, United Arap Emirates and Senegal).

We are a privately held corporation based in the Ankara, Turkey with manufacturing. Forfurther information about our company please contact [email protected]



www.acgelectronics.com

acg altiled presentation en

Documents