acrypet standard grades - lucite diakonlucitediakon.com/wp-content/uploads/2016/07/... · indice de...
TRANSCRIPT
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.comPlease visit us at:
lucitediakon.comPlease visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
Please visit us at:
lucitediakon.com
ACRYPETSTANDARD GRADES
ACRYPET ® Acrylic Polymers - Standard Grades
Please visit us at:lucitediakon.com
For further information visit our website:
www.lucitediakon.com
Acrypet Acrylic Polymers - Standard Grades
PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMIQUE THERMISCHE TERMICHE TÉRMICA Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTIQUES OPTISCHE OTTICHE OPTICA Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECANIQUES MECHANISCHE MECCANICHE MECANICA Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3 Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERALES ALLGEMEINE GENERALI GENERAL Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMIQUE THERMISCHE TERMICHE TÉRMICA Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTIQUES OPTISCHE OTTICHE OPTICA Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECANIQUES MECHANISCHE MECCANICHE MECANICA Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3 Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERALES ALLGEMEINE GENERALI GENERAL Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMIQUE THERMISCHE TERMICHE TÉRMICA Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTIQUES OPTISCHE OTTICHE OPTICA Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECANIQUES MECHANISCHE MECCANICHE MECANICA Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3 Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERALES ALLGEMEINE GENERALI GENERAL Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifi cations.Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control Freedom under patent, copyright and registered designs cannot be assumed. Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93 Haze Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93
Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTICAL OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93
Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMAL THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93
Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66 Elongation Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERAL GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84 Temperature Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93
Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66
Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
Acrypet Acrylic Polymers - Standard Grades
PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD UNITS METHODE D'ESSAI UNITES PRUFMETHODE EINHEIT VH VHM VH5 VHS MD MF METODO DI PROVA UNITA' DI MISURA METODO DE ENSAYO UNIDADES
THERMIQUE THERMISCHE TERMICHE TÉRMICA Melt Flow Rate Indice de Fluidité Schmelzflussrate Indice di Fluidità Indice de Fluidez ISO 1133 g/10mins (230 C / 37.3N) 2.0 3.1 5.5 6.0 6.0 14.0 Vicat Softening Point Point de Ramollissement Vicat Vicat Erweichungs - Temperatur Punto di Rammollimento Vicat Punto Reblandecimiento Vicat ISO 306B ºC 107 107 107 107 94 89 Heat Deflection Température de Wa̎rmeform besta̎ndigkeit Temperatura D'inflessione Temperatura Deformacion ISO 75A ºC 100 100 100 100 87 84
Fléchissement Sous Charge bei Belastung Sotto Carico Al Calor Coefficent of Expansion Coefficient de Dilatation La̎ngenausdehnungs-Koeffizient Coefficiente Di Dilatazione Coeficiente de Dilatación Lineal ASTM D696 1/C 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5 6 x 10-5
Linéaire Lineare
OPTIQUES OPTISCHE OTTICHE OPTICA Light Transmission Transmission Lumineuse Total Lichtdurchla̎ssigkeit Trasmissione Luminosa Totale Transmision de la Luz ISO13468 % at 3mm thickness 93 93 93 93 93 93
Turbidité Tru̎bung Torbidità Halo, Anieblamiento ISO14782 % at 3mm thickness 0.3 0.3 0.3 0.3 0.3 0.3 Refractive Index Indice de Réfraction Brechungsindex Indice di Rifrazione Indice Refracción ASTM D542 - 1.49 1.49 1.49 1.49 1.49 1.49
MECHANICAL MECANIQUES MECHANISCHE MECCANICHE MECANICA Tensile Strength Résistance à la Traction Zugfestigkeit Resistenza a Trazione Resistencia a la Tensión ISO 527 (1A/5) MPa 77 76 61 66 71 66
Allongement Reissdehnung Allungamento Alargamiento ISO 527 (1A/5) % 6.0 5.0 3.0 3.0 6.0 4.0 Flexural Modulus Module de Flexion Biege-E Modul Modulo in Flessione Modulo de Flexión ISO 178 GPa 3.3 3.3 3.3 3.3 3.3 3.2 Flexural Strength Résistance à la Flexion Biegefestigkeit Resistenza a Flessione Resistencia a la Flexión ISO 178 MPa 140 135 125 125 130 120 Charpy Impact Strength Résistance au Choc Schlagza̎higkeit Nach Resistanza All'Urto Charpy Resistencia al Impacto ISO 179/1eA kJ/m ² 1.4 1.4 1.3 1.3 1.4 1.3
Charpy Charpy Charpy ISO 179/1eU kJ/m ² 20 20 19 19 19 18
GENERALES ALLGEMEINE GENERALI GENERAL Relative Density Masse Volumique Dichtezahl Densità Relativa Densidad Relativa ISO 1183 - 1.19 1.19 1.19 1.19 1.19 1.19 Rockwell Hardness Dureté Rockwell Rockwell- Ha̎rte Durezza Rockwell Dureza Rockwell ISO 2039-2 M Scale 101 101 97 100 94 92 Mould Shrinkage Retrait au Moulage Verabeitungs-Schwindung Ritiro in Stampaggio Contracción de Moldeo - % 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 0.2 - 0.6 Water Absorption Absorption d'Eau Wasseraufnahme Assorbimento D'Acqua Absorción de Aqua ISO 62 (24hr) % 0.3 0.3 0.3 0.3 0.3 0.3
For further information visit our website: www.lucitediakon.com
The above data represents typical results obtained using standard test pieces, it should not form the basis of specifications.
Information contained in this publication (and otherwise supplied to users) is based on our general experience and is given in
good faith, but we are unable to guarantee its accuracy or to accept responsibility in respect of factors outside our knowledge or control
Freedom under patent, copyright and registered designs cannot be assumed.
Users of ACRYPET polymer should consult the relevant Material Safety Data Sheet
PROPERTY PROPRIETES EIGENSCHAFTEN PROPRIETÁ PROPIEDADES TEST METHOD METHODE D'ESSAI PRUFMETHODE METODO DI PROVA METODO DE ENSAYO
UNITS UNITES EINHEIT UNITA' DI MISURA UNIDADES
VH VHM VH5 VHS MD MF
OPTICAL Light Transmission Haze Refractive Index
OPTIQUES Transmission Lumineuse Total Turbidité Indice de Réfraction
OPTISCHE Lichtdurchla̎ Lichtdurchla Lichtdurchlassigkeit Tru̎ Tru Trubung Brechungsindex
OTTICHE Trasmissione Luminosa Totale Torbidità Indice di Rifrazione
OPTICA Transmision de la Luz Halo, Anieblamiento Indice Refracción
ISO13468ISO14782ASTM D542
% at 3mm thickness % at 3mm thickness -
930.3
1.49
930.3
1.49
930.3
1.49
930.3
1.49
930.3
1.49
930.3
1.49
GENERAL Relative Density Rockwell Hardness Mould Shrinkage Water Absorption
GENERALES Masse Volumique Dureté Rockwell Retrait au Moulage Absorption d'Eau
ALLGEMEINE Dichtezahl Rockwell- Ha̎ Rockwell- Ha Rockwell- Harte Verabeitungs-Schwindung Wasseraufnahme
GENERALI Densità Relativa Durezza Rockwell Ritiro in Stampaggio Assorbimento D'Acqua
GENERAL Densidad Relativa Dureza Rockwell Contracción de Moldeo Absorción de Aqua
ISO 1183 ISO 2039-2 - ISO 62 (24hr)
- M Scale % %
1.19101
0.2 - 0.60.3
1.19101
0.2 - 0.60.3
1.1997
0.2 - 0.60.3
1.19100
0.2 - 0.60.3
1.1994
0.2 - 0.60.3
1.1992
0.2 - 0.60.3