acuo 9o8 serie - broadcasting services · 2015. 4. 20. · acuo 908 aev broadcast srl tel. +39 051...
TRANSCRIPT
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
ACUO ACUO ACUO ACUO
AEV On Air broadcast consoleAEV On Air broadcast consoleAEV On Air broadcast consoleAEV On Air broadcast console
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
1
ACUO ACUO ACUO ACUO 9999O8 SerieO8 SerieO8 SerieO8 Serie
AEV On Air broadcast consoleAEV On Air broadcast consoleAEV On Air broadcast consoleAEV On Air broadcast console
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
O8 SerieO8 SerieO8 SerieO8 Serie
AEV On Air broadcast consoleAEV On Air broadcast consoleAEV On Air broadcast consoleAEV On Air broadcast console
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
Guarantee The equipment is warranted for a period of 2 years from the date of invoice (ex
warranty does not cover faults provoked by carelessness, natural causes and par
to wear. In addition, the cost of shipment is not covered. The warranty will be voided if the
equipment is mishandled.
Technical Support If you require technical support, contact AEV SERVICE giving a clear and concise account of
your speciic problem. Quote the serial number of your equipment by referring to the AEV
nameplate attached to the equipment itself as this is the most important piece of information
to be provided.
Telephone: +39 051 6630904 Fax:
Factory Service and Repairs If problems arise while the equipment is being installed, consult this manual and check that
the installation is being carried out properly. If the problems still cannot be solved, call the AEV
SERVICE Department for further information. If the problem
call will probably sufice. If, on the other hand, the equipment is to be shipped to AEV for
service or repairs.
Shipping Instruction When shipping the equipment to AEV, use the original package in order to be certain tha
be fully protected during handling. If you need the original package, call us for a new one.
If you ship the equipment in a different packing container, take care to provide a double
package by interposing padding material between the two contain
the equipment during shipment. The package should be marked “FRAGILE” in red.
Remember that the RMA number must be clearly visible on the package. If it is not, the
equipment will not be accepted.
IMPORTANT: Carefully read th
operator safety and directions regarding the installation, operation and maintenance of the
equipment.
Failure to observe the safety instructions and information given in this manual
infringement of the safety rules and design
equipment.
AEV Broadcast Srl declines all responsibility
not observed.
AEV Broadcast Srl declines all responsibility
The equipment is to be used by people capable of operating it in a trouble
is assumed that they are aware of the following safety rules.
• Keep this manual with the utmost care and close at hand so tha
whenever needed
• After unpacking the equipment, check it for condition.
• Avoid banging the equipment.
• The packing material (plastic bags, polystyrene, nails, etc.) must never be left within the
reach of the children, as these item
• Do not use the equipment in places where the temperature is not within the
range, as specified by the manufacturer.
• Before connecting the equipment, make sure the nameplate specifications
mains electricity supply (the nameplate is located on the equipment enclosure).
• Do not remove the sticker from the equipment as it contains important
relevant serial number.
• To join the equipment to the mains supply, use the pow
equipment.
• The equipment must be used only for the purpose it was designed for.
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
2
The equipment is warranted for a period of 2 years from the date of invoice (ex
warranty does not cover faults provoked by carelessness, natural causes and par
to wear. In addition, the cost of shipment is not covered. The warranty will be voided if the
If you require technical support, contact AEV SERVICE giving a clear and concise account of
oblem. Quote the serial number of your equipment by referring to the AEV
nameplate attached to the equipment itself as this is the most important piece of information
Fax: +39 051 893605
If problems arise while the equipment is being installed, consult this manual and check that
the installation is being carried out properly. If the problems still cannot be solved, call the AEV
SERVICE Department for further information. If the problem is a minor one we can a telephone
call will probably sufice. If, on the other hand, the equipment is to be shipped to AEV for
When shipping the equipment to AEV, use the original package in order to be certain tha
be fully protected during handling. If you need the original package, call us for a new one.
If you ship the equipment in a different packing container, take care to provide a double
package by interposing padding material between the two containers in order to fully protect
the equipment during shipment. The package should be marked “FRAGILE” in red.
Remember that the RMA number must be clearly visible on the package. If it is not, the
equipment will not be accepted.
Carefully read this paragraph as it contains important instructions concerning
operator safety and directions regarding the installation, operation and maintenance of the
Failure to observe the safety instructions and information given in this manual
infringement of the safety rules and design specifications provided for this piece of
declines all responsibility if any one of the safety rules given here
all responsibility if the end-user resells the product.
The equipment is to be used by people capable of operating it in a trouble-
is assumed that they are aware of the following safety rules.
• Keep this manual with the utmost care and close at hand so that it can be consulted
• After unpacking the equipment, check it for condition.
• Avoid banging the equipment.
• The packing material (plastic bags, polystyrene, nails, etc.) must never be left within the
these items are potential sources of danger.
• Do not use the equipment in places where the temperature is not within the
by the manufacturer.
• Before connecting the equipment, make sure the nameplate specifications
mains electricity supply (the nameplate is located on the equipment enclosure).
• Do not remove the sticker from the equipment as it contains important specifications and the
• To join the equipment to the mains supply, use the power cord purchased with the
• The equipment must be used only for the purpose it was designed for.
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
The equipment is warranted for a period of 2 years from the date of invoice (ex-works). The
warranty does not cover faults provoked by carelessness, natural causes and parts subject
to wear. In addition, the cost of shipment is not covered. The warranty will be voided if the
If you require technical support, contact AEV SERVICE giving a clear and concise account of
oblem. Quote the serial number of your equipment by referring to the AEV
nameplate attached to the equipment itself as this is the most important piece of information
If problems arise while the equipment is being installed, consult this manual and check that
the installation is being carried out properly. If the problems still cannot be solved, call the AEV
is a minor one we can a telephone
call will probably sufice. If, on the other hand, the equipment is to be shipped to AEV for
When shipping the equipment to AEV, use the original package in order to be certain that it will
be fully protected during handling. If you need the original package, call us for a new one.
If you ship the equipment in a different packing container, take care to provide a double
ers in order to fully protect
the equipment during shipment. The package should be marked “FRAGILE” in red.
Remember that the RMA number must be clearly visible on the package. If it is not, the
is paragraph as it contains important instructions concerning
operator safety and directions regarding the installation, operation and maintenance of the
Failure to observe the safety instructions and information given in this manual constitutes an
specifications provided for this piece of
if any one of the safety rules given here in is
user resells the product.
-free manner and it
t it can be consulted
• The packing material (plastic bags, polystyrene, nails, etc.) must never be left within the
.
• Do not use the equipment in places where the temperature is not within the recommended
• Before connecting the equipment, make sure the nameplate specifications correspond to the
mains electricity supply (the nameplate is located on the equipment enclosure).
specifications and the
er cord purchased with the
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
• Abuse or misuse of the equipment is
The manufacturer declines all responsibility for damage an
use and mishandling.
• Certain basic safety rules must be observed when using electrical equipment, in particular:
Never touch the equipment with wet and/or damp hands or other parts of the body.
- Keep the equipment away from drops of water or sprinkling systems.
- Never use the equipment near high heat sources or explosive material.
- Do not introduce any extraneous matter into the equipment.
- Do not allow children or untrained people to use the equipment.
• Before cleaning or servicing the equipment outside, disconnect it from the supply and wait at
least 2 seconds before working on it, as recommended by current safety regulations.
• In the event of faults and/or improper operation, turn off the equipment, shut off the
electrical power and call your dealer.
• Do not attempt to make repairs and/or adjustments when covers/guards or circuit boards are
to be removed.
• Blown fuses inside the power supply indicate that there may be a fault in
itself. The fuses must be replaced by qualified
your nearest dealer.
• Call your dealer for any repairs and be certain original spare parts are used.
Failure to observe this rule may adversely affect the safety level of your
• The equipment is to be connected to the mains supply and provided with
efficient earth conductors.
• The electrical wiring must be done in compliance with current electrical codes
“Electrical specification for domestic b
• When installing, leave a clearance of at least 1 cm around the equipment to
freely.
NOTE. This piece of equipment has been manufactured
workmanship. It must be used
long-term dependable operation.
The installation must be done in order to be able to guarantee an easy access to the cable of
feeding.
The device of dissection of the equipment is the cable of feeding, so it must be unconnected
from the equipment every time it is necessary to do any type of maintenance.
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
3
• Abuse or misuse of the equipment is extremely dangerous for people, pets and property.
The manufacturer declines all responsibility for damage and injury resulting from
• Certain basic safety rules must be observed when using electrical equipment, in particular:
Never touch the equipment with wet and/or damp hands or other parts of the body.
from drops of water or sprinkling systems.
Never use the equipment near high heat sources or explosive material.
Do not introduce any extraneous matter into the equipment.
Do not allow children or untrained people to use the equipment.
ning or servicing the equipment outside, disconnect it from the supply and wait at
least 2 seconds before working on it, as recommended by current safety regulations.
• In the event of faults and/or improper operation, turn off the equipment, shut off the
electrical power and call your dealer.
• Do not attempt to make repairs and/or adjustments when covers/guards or circuit boards are
• Blown fuses inside the power supply indicate that there may be a fault in
s must be replaced by qualified and authorised persons. It is advisable to call
• Call your dealer for any repairs and be certain original spare parts are used.
Failure to observe this rule may adversely affect the safety level of your
• The equipment is to be connected to the mains supply and provided with
• The electrical wiring must be done in compliance with current electrical codes
for domestic buildings”.
• When installing, leave a clearance of at least 1 cm around the equipment to
NOTE. This piece of equipment has been manufactured to the highest standards of
workmanship. It must be used properly and serviced as recommended to ensure
dependable operation.
The installation must be done in order to be able to guarantee an easy access to the cable of
The device of dissection of the equipment is the cable of feeding, so it must be unconnected
pment every time it is necessary to do any type of maintenance.
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
for people, pets and property.
d injury resulting from improper
• Certain basic safety rules must be observed when using electrical equipment, in particular: -
Never touch the equipment with wet and/or damp hands or other parts of the body.
ning or servicing the equipment outside, disconnect it from the supply and wait at
least 2 seconds before working on it, as recommended by current safety regulations.
• In the event of faults and/or improper operation, turn off the equipment, shut off the
• Do not attempt to make repairs and/or adjustments when covers/guards or circuit boards are
• Blown fuses inside the power supply indicate that there may be a fault in the power supply
persons. It is advisable to call
• Call your dealer for any repairs and be certain original spare parts are used.
Failure to observe this rule may adversely affect the safety level of your equipment.
• The equipment is to be connected to the mains supply and provided with adequate and
• The electrical wiring must be done in compliance with current electrical codes CEI 64-8
• When installing, leave a clearance of at least 1 cm around the equipment to allow air to pass
to the highest standards of
nded to ensure
The installation must be done in order to be able to guarantee an easy access to the cable of
The device of dissection of the equipment is the cable of feeding, so it must be unconnected
pment every time it is necessary to do any type of maintenance.
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
Contents
Guarantee...............................Technical Support ................................. ....................Factory Serv ice and Repairs ................................... ........Shipping Instruction .............................. ....................Precautions ......................Contents .........................Features ......................................Input functions and channels .....Input channel configuration ....................... ..............5Outputs ................................External controls ......................Monitoring .............................Input configuration .....Input setting ................................................... ......5Master outputs..................................... ....................6External control................................... ....................6Monitoring .................................Micro - Line channel .............Digital - Line Module .USB - Line Module ....................................... ....... 9Monitoring section .......Telephone hybrid section .........Control Room & Control Master setupu section ............................. ............ 11Rear Panel – C onnections .....................RJ connectors & Logic I/O Logic I/O functions ............................... ............ 15Telephone hybrids – operaTechnical specifications .........
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
4
Guarantee............................... ...............................2Technical Support ................................. ....................
ice and Repairs ................................... ........Shipping Instruction .............................. ....................Precautions ...................... .............................. 3Contents ......................... .....................Features ...................................... ................. 5Input functions and channels ..... .............................. 5Input channel configuration ....................... ..............5Outputs ................................ ... ............................6External controls ...................... ...............................5Monitoring ............................. ...............................5
..... ............... ...............................5................................................... ......5
Master outputs..................................... ....................6External control................................... ....................6Monitoring ................................. ...........................6
............. .. ............................ 7. ........... .............................. 8
Line Module ....................................... ....... 9Monitoring section ....... ..................................... 10Telephone hybrid section ......... ............................. 10
Control Studio sect ion ......................... 11Master setupu section ............................. ............ 11
onnections ..................... ................. 12& Logic I/O pin out .... ........................
Logic I/O functions ............................... ............ 15opera tion ................... .............. 16
Technical specifications ......... ............................. 1
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
...............................2 Technical Support ................................. .................... 2
ice and Repairs ................................... ........ 2 Shipping Instruction .............................. .................... 2
.............................. 3
..................... ......... 4 ................. 5
.............................. 5 Input channel configuration ....................... ..............5
............................6 ...............................5 ...............................5 ...............................5
................................................... ......5 Master outputs..................................... ....................6 External control................................... ....................6
...........................6 ............................ 7
.............................. 8 Line Module ....................................... ....... 9
..................................... 10 ............................. 10 ion ......................... 11
Master setupu section ............................. ............ 11 ................. 12
........................ . 13 Logic I/O functions ............................... ............ 15
.............. 16 ............................. 1 7
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
Features
audio inputs:
8 double-channels
balanced Micro and line inputs, digital AES/EBU, USB audio
Faders:
Faders (100 mm) with A/B input selector
Input functions and channels
- Four Microphone inputs:
- Eitgh stereo line inputs:
- Two digital AES/EBU input
- Two USB audio inputs:
Input channels configuration:
Channel 1 : MIC1 / LINE1
Channel 2 : MIC2 / LINE2
Channel 3 : MIC3 / LINE3
Channel 4 : MIC4 / LINE4
Channel 5 : DIG1 / LINE5
Channel 6 : DIG2 / LINE6
Channel 7 : USB1 / LINE7
Channel 8 : USB2 / LINE8
Input setting
All settings are independent for each input,
Channel setting:
- Gain / Level adjustment
- Input balance
- tone equalizer High, Medium , Low
- Private tel
- Control Studio
- PGM assignement
- C. Room Mute
- ST MU
- Tally 1
- Tally 2
- Talk back on C.Studio
- Phantom Power (only for Micro inputs)
Also you can to select the Bus assignment
- PGM
- UTL
- AUX
- CUE
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
5
, digital AES/EBU, USB audio I/O interface
Faders (100 mm) with A/B input selector, 3 bands tones control on each input.
Input functions and channels
( MIC1, MIC2, MIC3, MIC4 )
( LIN2, LIN3, LIN4, LIN5, LIN6, LIN7,
Two digital AES/EBU input: ( DIG1, DIG2 )
( USB1, USB2 )
Input channels configuration:
All settings are independent for each input, via encoder.
-12÷+12 dB
-12÷+12 dB
equalizer High, Medium , Low -14÷+14 dB
OFF/ON
OFF/ON
SPEECH/MUSIC
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
(only for Micro inputs) OFF/ON
Bus assignment pushing the following buttons:
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
on each input.
LIN7, LIN8 )
pushing the following buttons:
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
Master Outputs PGM:Analog balanced stereo with XLR connectors
UTL: Analog balanced stereo with XLR connectors
AUX: Analog balanced stereo with RJ45 connector
PGM Dig: digital AES/EBU stereo with RJ45 connector
UTL Dig: digital AES/EBU stereo with RJ45 connect
Auxiliary outputs
Control Room: Analog balanced stereo with RJ45 connector
Control Studio: Analog balanced stereo with RJ45 connector
Mute C. Studio: Analog balanced stereo with RJ45 connector
Headphone : Analog stereo with
Auxiliary input
External : Analog balanced stereo with RJ45 connector
External controls - Remote Fader with logic controls, (
- GPI Opto-isolated logic inputs
- GPO Opto-isolated logic outputs
Monitoring - Level control for headphone, Control Room, Control Studio
- External inputs for Monitor
- Headphone with integrated ampli
- double stereo digital VU-Meter on
inputs encoder
channels fader section
start channel display
channels assignement
busses assignement
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
6
with XLR connectors
with XLR connectors
Analog balanced stereo with RJ45 connector
stereo with RJ45 connector
digital AES/EBU stereo with RJ45 connector
Analog balanced stereo with RJ45 connector
Analog balanced stereo with RJ45 connector
Analog balanced stereo with RJ45 connector
Analog stereo with Jack 6,3 mm connector
Analog balanced stereo with RJ45 connector
Fader with logic controls, (START/STOP) with RJ45 connector
isolated logic outputs
dphone, Control Room, Control Studio mutable
with integrated amplifier
Meter on the TFT display PGM ( fixed ) SEL ( EXT, UTL, AUX )
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
the TFT display PGM ( fixed ) SEL ( EXT, UTL, AUX )
C.Room & C.Studio section
Telephone hybrid section
Encoder Master
VU display section
Digital TFT display
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
Micro - Line channel ( cha All controls on the Micro-Line input channel are described below.
1
2
3
4
5
6
7
8
9
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
7
( channels 1 – 4 )
Line input channel are described below.
1 – START lamp, it lights when
active
2 – knob jog ; directly it select the Gain input leve
range is -12 ÷ +12 dB
in sequence, the following commands:
1th push-buttom Balance adjust
2th push-buttom Treble band adjust
3th push-buttom Middle band adjust
4th push-buttom Bass band adjust
5th push-buttom Private Tel active (OFF/ON
6th push-buttom TB Studio to C.Room active (OFF/ON
7th push-buttom PGM bus selection (
8th push-buttom Control Room Mute
9th push-buttom Mute C.Studio active (OFF/ON
10th push-buttom Tally active (OFF/ON
11th push-buttom TB Regia to C. Studio
(OFF/ON)
12th push-buttom Phantom power for the
condenser microphone active ( OFF/ON )
3 – MIC to activate the microphone source (only with
the channel in STOP)
microphones.
4 – LINE to activate the line source (only with the
channel in STOP)
5 – PGM Button for routing the channel to the PGM bus.
6 – UTL Button for routing the channel to the UTL bus.
7 – AUX Button for routing the channel to the AUX bus.
8 - Button enabling the preview CUE.
9 - Fader.
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
lights when the channel fader is
select the Gain input level the
÷ +12 dB;
in sequence, the following commands:
buttom Balance adjust (-12 ÷ +12 dB)
buttom Treble band adjust (-14 ÷ +14 dB)
buttom Middle band adjust (-14 ÷ +14 dB)
buttom Bass band adjust (-14 ÷ +14 dB)
active (OFF/ON)
TB Studio to C.Room active (OFF/ON)
bus selection ( Speech/ Music)
buttom Control Room Mute active (OFF/ON)
Mute C.Studio active (OFF/ON)
active (OFF/ON)
to C. Studio active
buttom Phantom power for the
active ( OFF/ON )
to activate the microphone source (only with
E to activate the line source (only with the
PGM Button for routing the channel to the PGM bus.
UTL Button for routing the channel to the UTL bus.
Button for routing the channel to the AUX bus.
review CUE.
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
Dig - Line Module ( channels 5 All controls on the Dig-Line input channel are described below.
1
2
3
4
5
6
7
8
9
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
8
( channels 5 – 6 )
Line input channel are described below.
1 – START lamp, it lights when
active
2 – knob jog ; directly it sele
the range is -12 ÷ +12 dB
in sequence, the following commands:
1th push-buttom Balance adjust
2th push-buttom Treble band adjust
3th push-buttom Middle band adjust
4th push-buttom Bass band adjust
5th push-buttom Private Tel
6th push-buttom TB Studio to C.Room active
(OFF/ON)
7th push-buttom PGM bus selection (
8th push-buttom Control Room Mute
9th push-buttom Mute C.Studio active (OFF/ON)
10th push-buttom Tally active (OFF/ON)
11th push-buttom TB Regia
(OFF/ON)
3 – DIG to activate the digital
with the channel in STOP)
4 – LINE to activate the line source (only with the
channel in STOP)
5 – PGM Button for routing the channel to the PGM
bus.
6 – UTL Button for routing the channel to the UTL bus.
7 – AUX Button for routing the channel to the AUX
bus.
8 - Button enabling the preview CUE.
9 - Fader.
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
lights when the channel fader is
select the Gain input level
12 ÷ +12 dB;
in sequence, the following commands:
buttom Balance adjust (-12 ÷ +12 dB)
buttom Treble band adjust (-14 ÷ +14 dB)
buttom Middle band adjust (-14 ÷ +14 dB)
Bass band adjust (-14 ÷ +14 dB)
buttom Private Tel active (OFF/ON)
TB Studio to C.Room active
bus selection ( Speech/ Music)
buttom Control Room Mute active (OFF/ON)
Studio active (OFF/ON)
active (OFF/ON)
Regia to C.Studio active
digital AES/EBU source (only
LINE to activate the line source (only with the
PGM Button for routing the channel to the PGM
UTL Button for routing the channel to the UTL bus.
Button for routing the channel to the AUX
Button enabling the preview CUE.
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
USB - Line Module ( chann
All controls on the USB-Line input channel are described below.
1
2
3
4
5
6
7
8
9
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
9
( channels 7 – 8 )
Line input channel are described below.
1 – START lamp, it lights when
active
2 – knob jog ; directly it select the Gain input leve
the range is -12 ÷ +12 dB
in sequence, the following commands:
1th push-buttom Balance adjust
2th push-buttom Treble band adjust
3th push-buttom Middle band adjust
4th push-buttom Bass band adjust
5th push-buttom Private Tel
6th push-buttom TB Studio to C.Room active
(OFF/ON)
7th push-buttom PGM bus selection (
8th push-buttom Control Room Mute
(OFF/ON)
9th push-buttom Mute C.Studio active (OFF/ON)
10th push-buttom Tally act
11th push-buttom TB Regia
(OFF/ON)
3 – USB to activate the digital usb
the channel in STOP)
4 – LINE to activate the line source (only with the
channel in STOP)
5 – PGM Button for routing the channel t
bus.
6 – UTL Button for routing the channel to the UTL
bus.
7 – AUX Button for routing the channel to the AUX
bus.
8 - Button enabling the preview CUE.
9 - Fader.
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
lights when the channel fader is
select the Gain input level
12 ÷ +12 dB;
in sequence, the following commands:
buttom Balance adjust (-12 ÷ +12 dB)
buttom Treble band adjust (-14 ÷ +14 dB)
buttom Middle band adjust (-14 ÷ +14 dB)
buttom Bass band adjust (-14 ÷ +14 dB)
ivate Tel active (OFF/ON)
TB Studio to C.Room active
bus selection ( Speech/ Music)
buttom Control Room Mute active
Mute C.Studio active (OFF/ON)
active (OFF/ON)
Regia to C. Studio active
digital usb source (only with
LINE to activate the line source (only with the
PGM Button for routing the channel to the PGM
UTL Button for routing the channel to the UTL
Button for routing the channel to the AUX
Button enabling the preview CUE.
ACUO 908
AEV Broadcast Srl, via della Tecnica 33
Tel. +39 051 6630904 Fax +39 051 893605
Monitoring section
Telephone hybrids section
1 2 3
1A
2A
3A
4A
5A
6A
7A
8A
9A
10A
ACUO 908 Serie - AEV ON AIR CONSOLE
, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu e-
10
1 - Button for selecting the EXT input on
Switched digital VUMeters.
2 - Button for selecting the Master UTL output
on Switched digital VU-Meters.
3 - Button for selecting the Master AUX
on Switched digital VU-Meters.
Telephone hybrids section
1A - HOOK button for telephone line 1 hook
1B - HOOK button for telephone line 2 hook
2A - Button for Stanby state
2B - Button for Stanby state for telephone line 2.
3A - Button for TX+ adjust for telephone line 1.
3B - Button for TX+ adjust for telephone line 2.
4A - Button for TX- adjust for telephone line 1.
4B - Button for TX- adjust for telephone line 2.
5A - Button for RX+ adjust for telephone line 1.
5B - Button for RX+ adjust
6A - Button for RX- adjust for telephone line 1
6B - Button for RX- adjust for telephone line 2
7A - Button for assigning the tel1 to the PGM bus
7B - Button for assigning the tel2 to the PGM bus
8A - Button for assigning the t
8B - Button for assigning the tel2 to the UTL bus
9A - Button for assigning the tel2 to the AUX bus
9B - Button for assigning the tel2 to the AUX bus
10A -Button for assigning the tel2 to the CUE bus
10B -Button for assigning the
1B
2B
3B
4B
5B
6B
7B
8B
9B
10B
SOLE
40050 Argelato (BO) Italy
-mail [email protected]
Button for selecting the EXT input on
VUMeters.
Button for selecting the Master UTL output
Meters.
ton for selecting the Master AUX output
Meters.
HOOK button for telephone line 1 hook-up.
HOOK button for telephone line 2 hook-up.
Button for Stanby state for telephone line 1.
Button for Stanby state for telephone line 2.
adjust for telephone line 1.
Button for TX+ adjust for telephone line 2.
adjust for telephone line 1.
adjust for telephone line 2.
adjust for telephone line 1.
Button for RX+ adjust for telephone line 2.
adjust for telephone line 1.
adjust for telephone line 2.
Button for assigning the tel1 to the PGM bus.
Button for assigning the tel2 to the PGM bus.
Button for assigning the tel1 to the UTL bus.
Button for assigning the tel2 to the UTL bus.
Button for assigning the tel2 to the AUX bus.
Button for assigning the tel2 to the AUX bus.
Button for assigning the tel2 to the CUE bus.
or assigning the tel2 to the CUE bus.
ACUO 908
AEV Broadcast Srl
Tel. +39 051 6630904 Fax +39 051 893605
Room & Studio section
Control Studio selection 1 – Button for selecting the EXT input
routing it to the Control Studio output
2 – Button for selecting the master PGM output
for routing it to the Control Studio output3 – Button for selecting the master UTL output
for routing it to the Control Studio output4 – Button for selecting the master AUX output
for routing it to the Control Studio output5 – Button for selecting the CUE bus
it to the Control Studio output.
Control Room selection 6 – Button for selecting the EXT input
routing it to the Control Room outputs
7 – Button for selecting the master PGM output
for routing it to the Control Room output
8 – Button for selecting the master UTL output
for routing it to the Control Room output
9 – Button for selecting the master AUX output
for routing it to the Control Room output
Master setup
Master knob jog ; directly it select the Gain
in sequence, the following commands:
1 th push-buttom Control Room level (
2 th push-buttom Control Studio level
3 th push-buttom PGM output level
4th push-buttom External input level
5th push-buttom CUE interlock (OFF/ON)
6th push-buttom PGM Digital sample rate
7th push-buttom UTL Digital sample rate
8th push-buttom channel’s selection to GPIO 1
9th push-buttom channel’s selection to
10th push-buttom channel’s selection to GPO 3 ( Start/STOP C) command
1
2
3
4
5
ACUO 908 Serie - AEV ON AIR CONSOLE
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu
11
Room & Studio section
input for
output.
Button for selecting the master PGM output
output. Button for selecting the master UTL output
output. Button for selecting the master AUX output
output. Button for selecting the CUE bus for routing
Button for selecting the EXT input for
outputs.
Button for selecting the master PGM output
outputs.
ster UTL output
outputs.
Button for selecting the master AUX output
outputs.
Talk Back
10 – Button to active the
Control Studio outputs.
Talk back Regia to Studio
When the TB (talk back) button is pressed, the
signal of the enabled microphone is sent to the
Control Studio output.
• Channel with function talkback to studio
(TBST: ON)
• Channel in STOP
What happens:
• the Talk back button of the remote fader
lights up
• the previous selection of the Control Studio
flashes
• the audio signal present in the Control studio
is replaced by the channel selected in TB
Talk back Studio to Regia
(need the Remote Fader
• Channel connected to the Remote Fader unit
talkback function activated (ST
• Channel in STOP
What happens when the remote TB (talk back)
button is pressed:
• the Talk back button of
• the previous selection of the Control
flashes
• the audio signal present in the Control Room
is replaced by the channel connected to the
Remote Fader unit
• the signal of the enabled microphone is sent
to the Control Room output.
select the Gain headphone level, the range is -∞ ÷ +8 dB
lowing commands:
Control Room level (-∞ ÷ +8 dB)
Control Studio level (-∞ ÷ +8 dB)
PGM output level (-12 ÷ +12 dB)
ternal input level (-12 ÷ +12 dB)
CUE interlock (OFF/ON)
PGM Digital sample rate ( 32, 44.1, 48, 96 KHz )
UTL Digital sample rate ( 32, 44.1, 48, 96 KHz )
channel’s selection to GPIO 1 ( Start/STOP A) command
channel’s selection to GPIO 2 ( Start/STOP B) command
channel’s selection to GPO 3 ( Start/STOP C) command
6
7
8
9
10
SOLE
40050 Argelato (BO) Italy
e-mail [email protected]
the Talkback function to the
to Studio:
When the TB (talk back) button is pressed, the
signal of the enabled microphone is sent to the
Channel with function talkback to studio
he Talk back button of the remote fader
the previous selection of the Control Studio
the audio signal present in the Control studio
is replaced by the channel selected in TB
Regia :
Remote Fader)
connected to the Remote Fader unit with
lkback function activated (STCR: ON)
when the remote TB (talk back)
the Talk back button of ACUO flashes
the previous selection of the Control Room
the audio signal present in the Control Room
placed by the channel connected to the
the signal of the enabled microphone is sent
to the Control Room output.
∞ ÷ +8 dB;
AEV Broadcast Srl
Tel. +39 051 6630904
Rear panel – connections
Microphone inputs connection
Line inputs connection
Outputs & Ausiliary connection
7 5 3 1
8 6 4 2
9 11 13 15
10 12 14 16
17 19 21 23
24 18 20 22
XLR Outputs Head/USB/Logic & PWS
ACUO 908 Serie - AEV ON AIR CON
AEV Broadcast Srl, via della Tecnica 33 – 40050 Argelato (BO) Italy
Tel. +39 051 6630904 Fax +39 051 893605 Web site www.aev.eu
12
1 – Microphone 1 input XLR F connector
2 – Trimmer adjusting the MIC 1
to +30 dB for very low volume
3 – Microphone 2 input XLR F connector
4 – Trimmer adjusting the MIC 2
to +30 dB for very low volume
5 – Microphone 3 input XLR F connector
6 – Trimmer adjusting the MIC 3
to +30 dB for very low volume
7 – Microphone 4 input XLR F connector
8 – Trimmer adjusting the MIC 4
to +30 dB for very low volume
9 – Line 1 input RJ45 connector
10 – Line 2 input RJ45 connector
11 – Line 3 input RJ45 connector
12 – Line 4 input RJ45 connector
13 – Line 5 input RJ45 connector
14 – Line 6 input RJ45 connector
15 – Line 7 input RJ45 connector
16 – Line 8 input RJ45 connector
17 – Dig1 & Dig2 input RG45
18- Control Studio Mutable output RJ45 connector
19 – External input RG45 connector
20 – Control Room output RJ45 connector.
21 – AUX output RJ45 connector
22 – Control Studio output RJ45 connector.
23 – PGM Dig & UTLDig input
24 – Remote Fader RG45 connector
Line inputs Outputs & ausiliary Telephone line
AEV ON AIR CONSOLE
40050 Argelato (BO) Italy
www.aev.eu e-mail
XLR F connector.
MIC 1 input level from 0 ÷
to +30 dB for very low volume microphones.
XLR F connector.
MIC 2 input level from 0 ÷
to +30 dB for very low volume microphones.
XLR F connector.
MIC 3 input level from 0 ÷
to +30 dB for very low volume microphones.
XLR F connector.
MIC 4 input level from 0 ÷
to +30 dB for very low volume microphones
RJ45 connector.
RJ45 connector.
RJ45 connector.
RJ45 connector.
RJ45 connector.
RJ45 connector.
RJ45 connector.
RJ45 connector.
RG45 connector.
Control Studio Mutable output RJ45 connector
RG45 connector.
Control Room output RJ45 connector.
AUX output RJ45 connector
Control Studio output RJ45 connector.
input RG45 connector.
RG45 connector.
Microphone inputs
ACUO 908
AEV Broadcast Srl, via della Tecnica 33
Tel. +39 051 6630904 Fax +39 051 893605
Telephone connection
Outputs XLR connection
Head/USB/Logic & PWS connections
26 28
33 34
35 36 37 38
32 31 30 29
25 27
ACUO 908 Serie - AEV ON AIR CONSOLE
, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu e-
13
Head/USB/Logic & PWS connections
25 – Connector RJ45 for telephone
26 – Connector RJ45 for telephone service
27– Connector RJ45 for telephone line 2.
28– Connector RJ45 for telephone service 2.
29 – UTL left channel XLR connector
30 – UTL right channel XLR connector.
31 – PGM left channel XLR connector.
32 – PGM right channel XLR connector.
33 – Logic I/O DB15 connector
34 – PWS connector.
35 – Headphone jack 6,3 mm connector
36 – USB 1 connector.
37 – USB 2 connector.
38 – USB serial connection.
29
SOLE
40050 Argelato (BO) Italy
-mail [email protected]
Connector RJ45 for telephone line 1.
Connector RJ45 for telephone service 1.
Connector RJ45 for telephone line 2.
elephone service 2.
channel XLR connector.
channel XLR connector.
channel XLR connector.
PGM right channel XLR connector.
ogic I/O DB15 connector.
eadphone jack 6,3 mm connector.
ACUO 908
AEV Broadcast Srl, via della Tecnica 33
Tel. +39 051 6630904 Fax +39 051 893605
Line in /AUX/C.Room/C.Studio/Ext
RJ45 pin out
Digital Outputs RJ45 pin out
Remote fader RJ45 pin out
Tel line/ tel set RJ45 pin out
Logic I/O pin out
1o 8o
1p 8p
1e 8e
1t 8t
ACUO 908 Serie - AEV ON AIR CONSOLE
, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu e-
14
Line in /AUX/C.Room/C.Studio/Ext
pin out
1e – left channel +
2e – left channel –
3e – right channel +
4e – GND
5e – N.C.
6e – right channel –
7e – N.C.
8e – N.C 1° – left anne +
2° – left anne –
3° – right anne +
4° – GND
5° – N.C.
6° – right anne –
7° – N.C.
8° – N.C
1p – UTL dig +
2p – UTL dig –
3p – PGM dig +
4p – GND
5p – N.C.
6p – PGM dig +
7p – N.C.
8p – N.C.
1t – +5v
2t – IN
3t – Start/Stop L
4t – Start/Stop S
5t – Talk Back L
6t – Talk Back S
7t – GND
8t – GND
1 – 9 – GPO1 Start/Stop A; Start=close,
Stop=open
2 – 10 –GPO2 Start/Stop B; Start=close, Stop=open
3 – 11 – GPO Tally; (Start)+(Tally ON)
4 – 12 – GPO3 ; (Start) on attached c
5 – 13 – GPI1 Start/Stop IN A ; Toggle
6 – 14 – GPI2 Start/Stop IN B ; Toggle
7 – +5V
8 – GND
15 – GND
SOLE
40050 Argelato (BO) Italy
-mail [email protected]
GPO1 Start/Stop A; Start=close,
GPO2 Start/Stop B; Start=close, Stop=open
GPO Tally; (Start)+(Tally ON)
GPO3 ; (Start) on attached channel
GPI1 Start/Stop IN A ; Toggle
GPI2 Start/Stop IN B ; Toggle
ACUO 908
AEV Broadcast Srl, via della Tecnica 33
Tel. +39 051 6630904 Fax +39 051 893605
Out Start/Stop A: with the Master knob jog to the
the input channel, so when this channel is in Start, the contact between the pins 1 and 9 will close,
with the channel in Stop, the contact will open.
Out Start/Stop B: with the Master knob jog to the
the input channel, so when this channel is in Start
close, with the channel in Stop, the contact will open.
GPO Tally : this function is enabled
over to START mode, a stable contact is activate
GPO 3 with the Master knob jog to the
channel; when the channel changes over to START mode
pins 4 and 12.
In Start/Stop A: with the Master knob jog
assign the channel; so every time that the
the external circuit, the channel changes between the START
channel will sent to the external device by the
In Start/Stop B: with the Master knob jog
assign the channel; so every time that the
the external circuit, the channel changes between the START
channel will sent to the external device by the
ACUO 908 Serie - AEV ON AIR CONSOLE
, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu e-
15
Master knob jog to the GPIO1 ( Start/Stop A) function,
, so when this channel is in Start, the contact between the pins 1 and 9 will close,
with the channel in Stop, the contact will open.
Master knob jog to the GPIO2 ( Start/Stop B) function,
, so when this channel is in Start, the contact between the pins 2 and 10
close, with the channel in Stop, the contact will open.
nction is enabled ( ON ) by the channel’s encoder; when the
a stable contact is activate between the pins 3 and 11.
Master knob jog to the GPIO2 ( Start/Stop C) function, to assign the input
changes over to START mode, a stable contact is activate
Master knob jog select the function GPIO1 ( Start/Stop A)
every time that the opto-copled between the pins 5 and 13 will
e channel changes between the START and STOP mode. The state of the
sent to the external device by the Out Start/Stop A contact.
Master knob jog select the function GPIO2 ( Start/Stop
every time that the opto-copled between the pins 6 and 14
e channel changes between the START and STOP mode. The state of the
channel will sent to the external device by the Out Start/Stop B contact.
SOLE
40050 Argelato (BO) Italy
-mail [email protected]
function, to assign
, so when this channel is in Start, the contact between the pins 1 and 9 will close,
function, to assign
, the contact between the pins 2 and 10 will
the channel changes
assign the input
, a stable contact is activate between the
( Start/Stop A) and
between the pins 5 and 13 will active by
P mode. The state of the
( Start/Stop B) and
pins 6 and 14 will active by
STOP mode. The state of the
ACUO 908
AEV Broadcast Srl, via della Tecnica 33
Tel. +39 051 6630904 Fax +39 051 893605
Telephone hybrids – operation
• Incoming Phone Call: The button
• Attach incoming call: Press the
• Phone call on hold:
o HOOK ON
o press the STBY button, the external user
the corresponding telephone
• Communicate privately with
o HOOK (ON)
o STBY (ON)
o CUE (ON) of the selected
o PRIV TEL function atctive
o MIC channel in STOP
• Function Meeting of the two phone calls:
o (STBY OFF) enabled on the same bus
TEL1, TEL2 and a channel
o to listen to audio of the telephone lines
Room selection (Regia) and / or
ACUO 908 Serie - AEV ON AIR CONSOLE
, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu e-
16
utton HOOK flashes
: Press the HOOK (the button glows)
the external user hears the audio signal of the
telephone line
the external telephone user phone:
the selected telephone line
nction atctive (ON) of the microphone channel
phone calls:
the same bus ( PGM or UTL or AUX ) tothe
hannel with microphone
of the telephone lines to activate the corresponding bus
and / or C.Studio (Studio).
SOLE
40050 Argelato (BO) Italy
-mail [email protected]
of the selected bus on
hybrid channel
the corresponding bus in the C.
ACUO 908
AEV Broadcast Srl, via della Tecnica 33
Tel. +39 051 6630904 Fax +39 051 893605
TECHNICAL SPECIFICATIONS
Microphone Inputs
Input configuration
Input Impedance
Sensitivity Level Range
Input Level Range
Maximum Input Level
Phantom Supply
100 mm Fader
Connector
Line Inputs
Input configuration
Input Impedance
Input Level Range
Headroom
100 mm Fader control
Connector
Digital inputs
Input configuration
Sample Rate
100 mm Fader control
Connector
Telephone Hybrid
Input configuration
Input impedance
Line Compensation
Tx Level
Rx Level Range
Frequency response
Distortion
Noise
Analog Outputs
Output configuration
Output Impedance
PGM Output Level Range
Connector
UTL/AUX Output Level Range
Connector
C Room Mut.Output Lev.
Connector
Digital Outputs
Output configuration
Sample Rate
Connector
Headphones
configuration Type
Output Impedance
Connector
Logic I/O
Configuration
Max Voltage
Max Current
Connector
USB Port
Dimensions
ACUO 908 Serie - AEV ON AIR CONSOLE
, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu e-
17
Electronically balanced
200 Ω
Adjustable from –70 ÷-40 dBu (Trimmer adj.)
±12 dBu (Digital adj. step 0,5 dB)
- 30 dBu
48 Vdc selectable
VCA Digital controlled
XLR Female
Electronically balanced
10 K Ω (600 Ω wired)
±12 dBu (Digital adj. step 1,0 dB)
+ 18 dBu
VCA Digital controlled
RJ-45
AES/EBU, IEC958,S/PDIF & EIAJ CP340/1201
Automatic 32, 44.1, 48, 96 KHz converter
VCA Digital controlled
RJ-45
Opto-coupled
600 Ω Bal
Automatically (max 5 Km)
±12 dBu (Digital adj. step 0,5 dB)
±12 dBu (Digital adj. step 0,5 dB)
300 Hz ÷ 3400 Hz (-2 dB) ; 300 Hz ÷ 3400 Hz (
< 1.5 %
-60 dB.
Electronically balanced
100 Ω
-12 ÷ +12 dBu
XLR male
0 dBu fixed
RJ-45
- 12÷ +12 dBu
RJ-45
AES/EBU, IEC958,S/PDIF & EIAJ CP340/1201
Automatic 32, 44.1, 48, 96 KHz converter
RJ-45
Stereo unbalanced (C.Room no Muted)
50 Ω
JACK 6,3 mm
Optic solid state relay
50 Vdc/ac
100 mA
DSUB 15 pole female
2 x USB 2.0 interface
460 x 360 x 44 mm ( L x D x H )
SOLE
40050 Argelato (BO) Italy
-mail [email protected]
40 dBu (Trimmer adj.)
AES/EBU, IEC958,S/PDIF & EIAJ CP340/1201
300 Hz ÷ 3400 Hz (-1.5 dB)
EIAJ CP340/1201
ACUO 908
AEV Broadcast Srl, via della Tecnica 33
Tel. +39 051 6630904 Fax +39 051 893605
ACUO 908 Serie - AEV ON AIR CONSOLE
, via della Tecnica 33 – 40050 Argelato (BO) Italy
Fax +39 051 893605 Web site www.aev.eu e-
18
SOLE
40050 Argelato (BO) Italy
-mail [email protected]