Operating InstructioA... JI-TRANSMITTER BUTTON OPERATION:IMPORTANT: The microprocessor alarm system has been designed so that upon arming, a 10 second arming delaywill be effected. This is to give the electronics in the vehicle, a chance to stabilize. ( window roll-up, shock sensor)2-ACTIVE ARMING MODE:Arm the alarm system by pressing the transmitter button # 1, once momentarily. The alarm will arm and will confirmwith 1 siren arming chirp, LED will be solid and start to flash slow after 10 seconds3-PASSIVE ARMING MODE:In passive arming mode, upon closing the last door there will be a 30 second arming delay. The LED will be flashingrapidly indicating that the system is in passive arming phase. (programmable Dip switch #4)4-ARMING WITH DEFECTIVE ZONE ALERT:If after arming the alarm, a defective zone has been detected. The alarm will confirm the detection of the defectivezone by chirping the siren and flashing the lights 4 times, (30 seconds after the arming confirmation).5-DISARMING THE SYSTEM:T)isarmthe alarm system by pressing transmitter button # 1,once again momentarily. Alarm disarms and will confirm

J 2 disarming siren chirps - Lights will flash twice - LED will turn off - O~tional starter disable feature will.... Je de-activated, Door locks will unlock automatically - Domelight will be illuminated for 30 seconds or until ignition

key is turned to accessory "ON" position.6-PANIC MODE:For emergency situations, press and hold button #1, of the transmitter for 3 seconds. This will activate the panicmode. The alarm siren will sound and the parking lights will flash for 60 seconds (or until the transmitter button# I is pressed again for I second).7-ALARM TRIGGERED:Ifa violation of the vehicle is taking place, the siren will sound and the parking lights will flash for 60 seconds. Afterthis 60 ·seconds duration, the alarm will automatically reset and resume protecting the vehicle.8-INTRUSION ALERT:If a sensor input (door switch, shock sensor) has been violated while the system was armed, the LED will be flashingrapidly and upon disarming the alarm system, the siren will confirm with 3 disarming siren chirps and 3 light flashes.Check the vehicle and its contents to verifY if any violation has taken place.

DELTAVehicle Security System

~

GENESIS +Installation & Operating

Manual

9- ANTI - CAR JACKING WI IGNITION and DOOR: ( SPESIAL FEATURE )To activate the Car Jacking feature, Every Time Ignition is Turned (ON) 90 seconds later the siren will chirpfor 15 seconds to remind you that the system will be in car jacking mode. After the reminder, the parkinglights will flash & the siren will sound for 5 minutes, and the (-) Orange wire (Starter kill) will be activatedAfter Turned OFF it Will Repeat The Car Jacking it the door is opened.To turn the car jacking mode OFF, Ignition should be (ON) and press VALETswitch 2 times to reset the system.

to-AUTOMATIC FAULTY ZONE ELIMINATION:;hile armed, a faulty zone is detected and triggers the alarm, the siren will sound and the lights will flash for 2

Jes of 60 seconds duration each. Total 2 minutes. After these 2 cycles, the alarm will automatically reset andbypass the defective zone. Upon disarming the alarm system, 3 chirps will be audible and 3 light flashes will bevisible. This indicates that the alarm has been triggered. Upon rearming, the system will arm with 1 chirp and thenfollow up with 4 additional siren chirps and 4 light flashes. This indicates that a faulty zone has been detected, andhas been automatically bypassed.ll-VALET MODE: 2-step procedureThis feature is designed to temporarily disable the alarm for valet parking. While the alarm is in the disarmed state,insert the ignition key and turn to the ignition "ON" accessory position. Press & hold the valet switch for 5 seconds,the system will chirp, remove the key from the ignition. The alarm will now be in the valet mode, and the LEDwill be ON solid.NOTE: You cannot arm or disarm the alarm while the system is in valet mode. However, you can still use thetransmitter to lock and unlock the doors, while the alarm is in valet mode.ll-EMERGENCY OVERRIDE SWITCH:In the event that you lose you transmitter and cannot disarm the alarm:Open the door, the alarm will sound. Insert the ignition key and turn to the ignition "ON" accessory position. Press& Hold the valet switch for 5 seconds. The alarm will chirp & disarm, the LED will be solid, the starter disablefeature will be deactivated and you will now be able to start your car.

*Two 3 Channel Transmitters *120dB 6 Tone Siren*2nd Channel Output for Trunk release *Last Door Automatic Arming*3rd Channel Output for Remote Starter *Flashing Parking Lights*Door Entry Protection *Starter Disable*PersonalJPanic Feature *R.F. Lock-Out Safety Feature*Duale Zone Shock Sensor Plug-In *ValetOverride Switch Plug-In*Dome Light sopervision *Faulty Zone By-Pass*Remote Shock Sensor Disable *AudibleNisual Intrusion Alert*Five Function LED Plug-In *Door locking & Unlocking W/Ign.*Intrusion Evant Memory *Remote Door Lock/Unlock Plug-In

1- CODE TEACHING:Turn the ignition key 3 times on/off, on/off, on/off, the siren will chirp.Leave the ignition key in on position, press the valet switch for 5 seconds until the siren chirps 3times, Then press button # 1 on the remote transmitter. The siren will chirp once, if you want toteach another transmitter with different code press # 1 on the second transmitter the siren will chirponce. You can teach up to 3 different codes. Afterwards within 10 seconds the LED will startflashing, now the alarm has learned the code of the transmitters.2- .WARN-AWAY ,When using the dual zone shock sensor, the white wire provides a Warn-Away Input.When the alarm is armed, the first zone will chirp the siren 5 times and flash the parking lightsonce, and the second zone will trigger the alarm,3- VALET MODE:To get into Valet mode, Disarm the alarm, turn the Ignition ON, Push and hold the valet switch for5 seconds until the LED comes ON solid"The system will be in VALET. Only the door lock/unlocksystem will work on Valet (Keyless Entry).To get out of Valet mode, turn the ignition ON Push and hold the valet switch for 5 seconds, thealarm will chirp and the LED goes out.In an Emergency, When the alarm system has been triggered and the transmitters do not respondtoturn the alarm off. Get into the carturn the Ignition ON, hold the switch button down for5 seconds,the alarm will shut off and the LED will be on solid, this will override the system and it will be inValet Mode.4- SHOCK SENSOR DISABLE FEATURE:To disable the SHOCK SENSOR after arming the system. Press the 1st button once, immediatelyafter within 3 seconds press the 2nd button and the alarm will chirp one moretime, that will eliminateall trigger wires.5- AUTOMATIC RE-ARMING:When the alarm h?,s been disarmed with the transmitter by mistake. It will automatically rearm itselfwithin 30 seconds, unless you open one of the doors. This feature will be always active no matterif the alarm is in active or passive mode.6- MODIFYING TRIGGERS FOR REMOTE STARTER:When channels 2 or 3 are activated and within 3 seconds the remote starter will disable the current,shock, and warn away sensors, while the engine is running.The above changes were done for the following reason: When the alarm is on, and the remotestarter is activated, the vibration from the engine won't trigger the sensors.

DIP SWITCH CONTROL1- ON- 1 Second Door lock/Unlock (-) Pulse OFF- 3,5 Second Door Lock/Unlock Pulse2- ON- Door Lock/Unlock with Ignition OFF- DISABLED3- ON- Door Locking in Passive Mode OFF- No Door Locking in Passive Mode4- ON- Automatic Arming (Passive Mode) OFF- DISABLED

Changing the Factory Default Setting of the Dip Switch

1- Switch to OFF position, the Door Lock/Unlock wires will giveyou 3.5 seconds (-) Pulse. (use for Vacuum systems)

2- Switch to ON position, The Door will Lock & Unlockwith the Ignition Key turned to ON/OFF position.

3- Switch to OFF position, in Passive mode the door will not lock, onlyI the alarm will arm itself. (Automatic Arming).i 4- ~witch to~)!:!position~e_:I:rm ~ill arm itself in 30 second~_. _

Wiring Diagram

I- •• -I Dual Zone Shock St:nsor Plug

F Blue (-) DOOR UNLOCK]. -----Red (+) POWER _Optional DL-INV-2

_ (for positive Systems only)Green (-) DOOR LOCK

WHITERED

BROWN

BLACK

ORANGE

GRAY

GREEN

BLUE

VIOLET

YELLOW

(+) PARKING LIGHTS(+) POWER(+) SIREN OUTPUT(-)GROUND(-)OUTPUT(-)2nd CHANNEL(-)DOORTRIGGER(-) SENSOR TRIGGER(+) DOOR TRIGGER(+) IGNITiON 12V+

DOME LIGHT

~(-) HORN OUTPUT(-) 3 RD CHANNEL OUT-PUT

~ Valet Switch BLUE Plug

C!::.!J L.E.D. RED Plug

OOORLOCKIUNLOCKWIRING DIAGRAM

CURRENT SENSINGJUMPER Inside The Unit

ON = DISABLE (factory default)REMOVED = ENABLE

3 Wire Positive Door Lock SystemLock Wire of Alarm

Or use the optional

DL-IJ'oI'V

1- Para activar Iaalarma presione el boton numero "I", una vez(CARACTERISTICAS DE LA ALARMA ACTIV ADA)

A- La alarma confirma con un tonG y un titileo de luces.B- EI L.E.D. inicia a titilar una vez por segundo.C- Si esta conectado el cierre central, el carro hecha Have.D- El carro automMicamente se protege y no puede ser arrancado.E- Si e1 carro es golpeado suavemente la sirena dara un Pre aviso.F- Si el auto es golpeado fuertemente se dispara la sirena.G- Si las puertas 0 el baul son abiertos, se dispara la sirena.

2- Para des activar la alarma presione de nuevo el boton uno una vez:(CARACTERISTICAS DE LA ALARMA DESACTIV ADA)

A-La alamla confirma con dos tonos y dos titileos de luces.B-Si esta conectado el cierre central, el carro quita HaveC-EI carro libera la protecci6n y puede ser arrancadoD-EI L.E.D. inicia un titileo nipido.E- EI auto permaneceni des protegido.

3-Para activar Ia alanna de manera semi silenciosa, presione el boton dos y Iuego el uno.(NOT A: VER CARACTERISTICAS DE LA ALARMA ACTIV ADA)

La unica diferencia sera que la sirena confonnara con un tonG muy suave.

4-Para des activar Ia alanna de manera semi silenciosa, presione el boton dos y Iuego el uno.(NOT A: VER CARACTERISTICAS DE ALARMA DES ACTIV ADA)

La {mica diferencia sera que la alarm a confirmara con dos tonos muy suaves.

5-Para activar,la alanfla y desconectar el sensor de golpes: Presione el boton "I", en Ios subsiguientes 3segundos presione Ios dos botones simultaneamente.(La alarma tendra todas las caracteristicas de alarma activada, las funciones "EY F"no aplican.)Para volver a su estado normal desactive la alanna y luego re active de nuevo.Esta funci6n es para estacionar el carro en lugares de alta vibraci6n como lugares donde corren vehiculospesados 0 dias de mucha Huvia con truenos, etc. La protecci6n de puertas permanece pero desactiva la tapadel motor.

6-Para activar Ia alarma y desconectar proteccion de puertas baul y tapa del motor: Presione el boton"I", en menos de 3 segundos presione el boton "II"

(La alanna tendra todas las caracteristicas de alarma activada, las f\lIlciones "E, F y G" no aplican.)Para volver a su estado normal desactive la alarm a y luego re active de nuevo. Esta funci6n es para poder

dar el auto a una persona que 10 lave, pero no Ie entregamos las Haves, el podni entrar y mover el auto y lasirena no se disparani. En este estado el auto no arranca a menos que desactivemos la alanna-Modo deVALET temporal: Presione el bot6n "II", en menos de tres segundos presione y Inantenga presionado el bot6n

La sirena confinnara con un tonG corto y luego de unos segundos confinnani con cinco tonos cortos, estafunci6n desactivada la alarma temporalmente, la alarma no se activara automMicamente a menos que sepresione el bot6n "II"lo cual deja la alarma en modo des activado.

8-Modo de VALET permanentemente 0 modo de emergencias: Si su control remoto falla 0 si usted'<J.uiere desactivar Ia alarm a por cualquier motivo, siga Ios pasos a continuacion:

Si su control no responde: Usted debeni disparar la sirena (simplemente abriendo la puerta) y luegoSi su control esta respolldielldo: Desactive la alarma y luego siga los pasos a continuaci6n:

A- Coloque la Have en posici6n de "ON"B- Presione el switch de VALET hasta que el L.E.D. quede permanentemente encendido.