alcatel lucent pt telkom turn-up guide v1
TRANSCRIPT
PT Telkom Vectoring Field Trial
Method of ProcedureAlcatel-Lucent 7356REM ISAM Turn Up Guide
Author: Fiona TayDocument: Turn-up Guide
Version: 0.1Status: Draft
Last Revised: June 24, 2014
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 1 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
TABLE OF CONTENTS
1 PREFACE........................................................................................4
2 COMPATIBILITY...............................................................................4
3 CONVENTIONS................................................................................4
4 PRE-CONFIGURATION STEPS............................................................5
4.1 CONNECT TO THE 7360FX OLT & 7356REM MDU ISAM VIA CRAFT TERMINAL......5
5 OLT BASIC SETUP - INITIAL CONFIGURATION....................................7
5.1 RESET THE SYSTEM WITH CLEAN DATABASE..........................................................7
5.2 CONFIGURE UPLINK PORTS................................................................................7
5.3 CONFIGURE MANAGEMENT VLAN.......................................................................7
5.4 CONFIGURE SYSTEM IP ADDRESS.......................................................................7
5.5 CONFIGURE SYSTEM ID....................................................................................8
5.6 CONFIGURE SYSTEM PROMPT............................................................................8
5.7 CONFIGURE SYSTEM LOGIN BANNER....................................................................8
5.8 CONFIGURE SLOT BANDWIDTH..........................................................................8
5.9 CONFIGURE SLOT NUMBERING & DHCP OPTION82 FORMAT..................................8
5.10 DISABLE PASSWORD AGING & TIMEOUT FOR OPERATOR LOGIN..............................8
5.11 CONFIGURE THE SNMP COMMUNITIES.............................................................9
5.12 SAVE THE CONFIGURATION............................................................................9
5.13 CONFIGURE SNTP.......................................................................................9
5.14 PLAN ALL INSERTED CARDS............................................................................9
5.15 ENABLE PON PORTS....................................................................................9
5.16 REBOOT 7360FX OLT...............................................................................10
6 MDU BASIC SETUP - INITIAL CONFIGURATION.................................11
6.1 RESET THE SYSTEM WITH CLEAN DATABASE........................................................11
6.2 CONFIGURE UPLINK PORTS..............................................................................11
6.3 CONFIGURE MANAGEMENT VLAN.....................................................................11
6.4 CONFIGURE SYSTEM IP ADDRESS.....................................................................11
6.5 CONFIGURE SYSTEM ID..................................................................................11
6.6 CONFIGURE SYSTEM PROMPT..........................................................................12
6.7 CONFIGURE SYSTEM LOGIN BANNER..................................................................12
6.8 CONFIGURE SLOT BANDWIDTH........................................................................12
6.9 CONFIGURE SLOT NUMBERING & DHCP OPTION82 FORMAT................................12
6.10 DISABLE PASSWORD AGING & TIMEOUT FOR OPERATOR LOGIN............................12
6.11 CONFIGURE THE SNMP COMMUNITIES...........................................................13
6.12 SAVE THE CONFIGURATION..........................................................................13
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 2 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
6.13 CONFIGURE SNTP.....................................................................................13
6.14 PLAN ALL INSERTED CARDS..........................................................................13
6.15 REBOOT ISAM..........................................................................................13
7 OLT SERVICE PROVISIONING - INITIAL CONFIGURATION...................14
7.1 CREATE UPSTREAM BANDWIDTH PROFILES (DBA)...............................................14
7.2 CREATE DOWNSTREAM SHAPER PROFILES..........................................................14
7.3 CREATE PBIT TO TC MAPPING PROFILES............................................................14
7.4 CONFIGURE SYSTEM MULTICAST FOR IPTV........................................................14
7.5 CREATE VLANS...........................................................................................15
8 MDU SERVICE PROVISIONING - INITIAL CONFIGURATION.................17
8.1 CREATE VECTORING CONTROL ENTITY (VCE) PROFILE AND ASSOCIATE IT TO A BOARD
17
8.2 CREATE XDSL VECTORING PROFILES................................................................17
8.3 CREATE XDSL SERVICE PROFILES....................................................................17
8.4 CREATE XDSL SPECTRUM PROFILES.................................................................17
8.5 CREATE XDSL RTX PROFILES..........................................................................20
8.6 CONFIGURE SYSTEM MULTICAST FOR IPTV........................................................20
8.7 CREATE VLANS...........................................................................................21
8.8 CREATE VOIP SERVICE..................................................................................21
9 SERVICE PROVISIONING – SAMPLE SERVICE CONFIGURATION..........23
9.1 CREATE SFP ONT INFRASTRUCTURE................................................................23
9.2 CONFIGURE SFP ONT UNI............................................................................23
9.3 CREATE HSI SERVICE ON SFP ONT.................................................................23
9.4 CREATE VOD + MULTICAST SERVICE ON SFP ONT............................................23
9.5 CREATE VOIP SERVICE ON SFP ONT...............................................................23
9.6 CREATE XDSL VECTORED LINE.......................................................................24
9.7 CREATE HSI SERVICE (RGW).........................................................................24
9.8 CREATE VOD + MULTICAST SERVICE...............................................................24
9.9 CREATE VOIP SERVICE..................................................................................24
10 USEFUL SHOW COMMANDS.........................................................24
10.1 VIEW VECTOR DISTURBERS ON VDSL2 VECTORING LINES..................................24
10.2 VIEW THE XDSL LINE STATUS......................................................................24
10.3 SHOW IGMP STATISTICS.............................................................................25
10.4 SHOW SIP STATISTICS................................................................................25
10.5 MIRROR ON OLT.......................................................................................25
10.6 MIRROR ON MDU......................................................................................25
11 DOCUMENT HISTORY..................................................................26
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 3 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
1 Preface
This document describes the process of configuring a 7356REM ISAM for use in PT Telkom network for the Vectoring Field Trial.
2 Compatibility
This document supports the configuration of the 7356REM ISAM with the following release:
ISAM R5.0 or higher
3 Conventions
The following conventions are used throughout this document: Courier New font: denotes to be entered commands, and their output.
The # prompt denotes login as root;
The > prompt denotes login as normal user.
Bold italics Arial font: denotes GUI actions (menu selections or buttons).
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 4 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
4 Pre-configuration steps
4.1 Connect to the 7360FX OLT & 7356REM MDU ISAM via Craft Terminal
Connect the PC’s Serial port to the craft port of the 7356REM ISAM (LCMI). The craft port is located on the NRNT-A card.
Pin-out of RJ45 connector:
Signal Description Pin TypeRI_DSR Data-Set-Ready 1 ODCD Data-Carrier-Detect 2 ODTR Data-Terminal-Ready 3 IEG Signal Ground 4 RefRXD Receive-Data 5 OTXD Transmit-Data 6 ICTS Clear-To-Send 7 ORTS Request-To-Send 8 I
Open HyperTerminal (or equivalent) and setup the serial connection with following parameters:
As soon as you connect the system will show following prompt:
Would you like a CLI(C) or a TL1 login(T) or TL1 normal session(N) ? [N]:
Choose ‘C’ to enter the TL1. The factory username and password are:
Username = isadmin
Password = i$@mad-
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 5 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
This password needs to be changed on first logon. Please change it to “ans#150” (without the quotes)
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 6 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
5 OLT Basic Setup - Initial configuration
5.1 Reset the system with clean database
Remove any existing configuration.
isadmin># admin software-mngt oswp 1 activate clear-db
Note: The system will reset and come up with an empty database. Follow step 4.1 to re-connect to the system.
5.2 Configure uplink ports
Configure 1 uplink to connect to the network, port 1 on NT in 1GE mode for connection to Metro-E.
isadmin># configure port nt-a:xfp:1 ethernet speed 1000
isadmin># configure port nt-a:xfp:1 ethernet autonegotiate limited
isadmin># configure port nt-a:xfp:1 no shutdown
Note: The ports have a MTU of 2000 Bytes configured by default
5.3[5.2] Configure management VLAN
Assign the management VLAN to Uplink.
isadmin># configure service vpls 82 customer 1 v-vpls vlan 82 create
isadmin># configure service vpls 82 description "management vlan"
isadmin># configure service vpls 82 nt-a:xfp:1:82 create
isadmin># configure service vpls 82 no shutdown
Note: The bold part needs to be replaced by the actual value found on the node information sheet
5.4[5.3] Configure System IP address
Assign the management IP address and routing table.
isadmin># configure system management host-ip-address manual:172.27.141.56/26
isadmin># configure system management default-route 172.27.141.1
Note: The bold part needs to be replaced by the actual value found on the node information sheet
Note: System is now reachable from EMS and the network.
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 7 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
5.5[5.4] Configure System ID
Configure the system name.
isadmin># configure system id 09-TDS-01;
Note: The bold part needs to be replaced by the actual value found on the node information sheet
5.6[5.5] Configure System Prompt
Configure the system prompt to represent the system name and use type based LT numbering.
isadmin># configure system security operator isadmin prompt "%s:%n@AR09-TDS-01%d%c"
Note: The bold part needs to be replaced by the actual value found on the node information sheet
Note: The total length of the prompt string needs to be less or equal than 28 characters. This means the system ID can only be 18 characters.
5.7[5.6] Configure system login banner
Configure the system CLI login banner
isadmin># configure system security login-banner "Access to the ISAM system is for authorized staff only"
isadmin># configure system security welcome-banner "Alcatel-Lucent 7360FX OLT"
5.8[5.7] Configure Slot Bandwidth
Configure the system slot bandwidth between the switching matrix and the Line cards (value is speed between line card and each controller)
isadmin># configure system max-lt-link-speed link-speed forty-gb
5.9[5.8] Configure Slot Numbering & DHCP Option82 Format
Configure the slot numbering format and the DHCP Option82 format
isadmin># configure system security profile admin slot-numbering type-based
isadmin># configure system port-num-in-proto type-based
isadmin># configure system loop-id-syntax efm-based-pon "Access_Node_ID eth Rack/Frame/Slot/Port/ONU/OnuSlt/UNI"
Note: After setting this slot numbering the operator needs to logout and login again to activate the new setting
5.10[5.9] Disable password aging & timeout for operator login
Disable the password aging and session time out for operator login
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 8 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
isadmin># configure system security profile admin password-timeout 0
isadmin># configure system security ssh server-profile idle-timeout 300
5.11[5.10] Configure the SNMP communities
To allow 5520AMS access, the host-address used is the IP address of the AMS, optionally this can be set to a subnet or 0.0.0.0/0 to allow access to all hosts.
isadmin># configure system security snmp community public host-address 10.153.5.65/32 context nt
isadmin># configure system security snmp community NETMAN host-address 10.153.5.65/32 context shub
Note: The bold part needs to be replaced by the actual value found on the node information sheet
5.12[5.11] Save the configuration
isadmin># admin software-mngt ihub database save-protected
5.13[5.12] Configure SNTP
Configure SNTP server for network time synchronization.
isadmin># configure system sntp server-ip-addr 10.153.5.65 timezone-offset 420 enable
Note: The bold part needs to be replaced by the actual value found on the node information sheet
Note: The NTP server IP points to the AMS Server
5.14[5.13] Plan all inserted cards
Configure all cards in the system
isadmin># configure equipment slot nt-a planned-type fant-f unlock
isadmin># configure equipment slot lt:1/1/1 planned-type nglt-c unlock
5.15[5.14] Enable PON Ports
Enable PON in the system.
isadmin># configure pon interface 1/1/1/1 admin-state up
isadmin># configure qos interface pon:1/1/1/1 ds-num-queue 8
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 9 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
5.16[5.15] Reboot 7360FX OLT
Reboot 7360FX OLT
isadmin># admin equipment reboot-isam without-self-test
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 10 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
6 MDU Basic Setup - Initial configuration
6.1 Reset the system with clean database
Remove any existing configuration.
isadmin># admin software-mngt oswp 1 activate clear-db
Note: The system will reset and come up with an empty database. Follow step 4.1 to re-connect to the system.
6.2 Configure uplink ports
Configure 1 uplink to connect to the network, port 1 on NT in 1GE mode for connection to OLT.
isadmin># configure interface shub port nt:sfp:1 port-type network mode 1gbps:full admin-status up
Note: The ports have a MTU of 2000 Bytes configured by default
6.3[6.2] Configure management VLAN
Assign the management VLAN to Link Aggregation Group.
isadmin># configure system mgnt-vlan-id 82
isadmin># configure system shub entry vlan ext-vlan-id 82
isadmin># configure vlan shub id 82 egress-port nt:sfp:1
Note: The bold part needs to be replaced by the actual value found on the node information sheet
6.4[6.3] Configure System IP address
Assign the management IP address and routing table.
isadmin># configure system management host-ip-address manual:127.72.141.57/26
isadmin># configure system management default-route 172.27.141.1
Note: The bold part needs to be replaced by the actual value found on the node information sheet
Note: System is now reachable from EMS and OLT
6.5[6.4] Configure System ID
Configure the system name.
isadmin># configure system id 09-TDS-01;
Note: The bold part needs to be replaced by the actual value found on the node information sheet
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 11 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
6.6[6.5] Configure System Prompt
Configure the system prompt to represent the system name and use type based LT numbering.
isadmin># configure system security operator isadmin prompt "%s:%n@09-TDS-01%d%c"
Note: The bold part needs to be replaced by the actual value found on the node information sheet
Note: The total length of the prompt string needs to be less or equal than 28 characters. This means the system ID can only be 18 characters.
6.7[6.6] Configure system login banner
Configure the system CLI login banner
isadmin># configure system security login-banner "Access to the ISAM system is for authorized staff only"
isadmin># configure system security welcome-banner "Alcatel-Lucent 7356REM MDU"
6.8[6.7] Configure Slot Bandwidth
Configure the system slot bandwidth between the switching matrix and the Line cards (value is speed between line card and each controller)
isadmin># configure system max-lt-link-speed link-speed twodotfive-gb
6.9[6.8] Configure Slot Numbering & DHCP Option82 Format
Configure the slot numbering format and the DHCP Option82 format
isadmin># configure system security profile admin slot-numbering type-based
isadmin># configure system port-num-in-proto type-based
isadmin># configure system loop-id-syntax efm-based-dsl "Access_Node_ID eth Rack/Frame/Slot/Port"
Note: After setting this slot numbering the operator needs to logout and login again to activate the new setting
6.10[6.9] Disable password aging & timeout for operator login
Disable the password aging and session time out for operator login
isadmin># configure system security profile admin password-timeout 0
isadmin># configure system security ssh server-profile idle-timeout 300
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 12 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
6.11[6.10] Configure the SNMP communities
To allow 5520AMS access , the host-address used is the IP address of the AMS, optionally this can be set to a subnet or 0.0.0.0/0 to allow access to all hosts.
isadmin># configure system security snmp community public host-address 10.153.5.65/32 context nt
isadmin># configure system security snmp community NETMAN host-address 10.153.5.65/32 context shub
Note: The bold part needs to be replaced by the actual value found on the node information sheet
6.12[6.11] Save the configuration
isadmin># admin software-mngt shub database save
6.13[6.12] Configure SNTP
Configure SNTP server for network time synchronization.
isadmin># configure system sntp server-ip-addr 10.153.5.65 timezone-offset 420 enable
Note: The bold part needs to be replaced by the actual value found on the node information sheet
Note: The NTP server IP points to the AMS Server
6.14[6.13] Plan all inserted cards
Configure all cards in the system
isadmin># configure equipment slot nt-a planned-type nrnt-a unlock
isadmin># configure equipment slot lt:1/1/1 planned-type ndlt-c unlock
isadmin># configure equipment slot lt:1/1/2 planned-type npot-c unlock
6.15[6.14] Reboot ISAM
Reboot the 7356REM MDU
isadmin># admin equipment reboot-isam without-self-test
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 13 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
7 OLT Service Provisioning - Initial configuration
7.1 Create Upstream Bandwidth Profiles (DBA)
Create Bandwidth profiles according to the type of service. These profiles regulate the DBA bandwidth and priority.
isadmin># configure qos profiles bandwidth UP_1G committed-info-rate 0 assured-info-rate 10000 excessive-info-rate 1000000 delay-tolerance 8
7.2 Create Downstream Shaper Profiles
Create Bandwidth profiles according to the type of service. These profiles are used for rate shaping on Line card
isadmin># configure qos profiles shaper DN_1G committed-info-rate 0 committed-burst-size 0 excess-info-rate 1000000 type singletokenbucketgpon
7.3 Create Pbit to TC Mapping Profiles
Create PBit to Traffic Class mapping profiles.
isadmin># configure qos profiles ingress-qos Default_TC0 dot1-p0-tc 0 dot1-p1-tc 0 dot1-p2-tc 0 dot1-p3-tc 0 dot1-p4-tc 0 dot1-p5-tc 0 dot1-p6-tc 0 dot1-p7-tc 0
isadmin># configure qos profiles ingress-qos Ingress_Default dot1-p0-tc 0 dot1-p1-tc 1 dot1-p2-tc 2 dot1-p3-tc 3 dot1-p4-tc 4 dot1-p5-tc 5 dot1-p6-tc 6 dot1-p7-tc 7
7.4 Configure System Multicast for IPTV
Enable Multicast on System Level:
isadmin># configure igmp system src-ip-address 10.88.43.222 query-interval 125 start user-igmp-version 2 netw-igmp-version 2
Create Multicast VLAN:
isadmin># configure vlan id 110 mode residential-bridge name IPTV new-broadcast enable in-qos-prof-name name:Default_TC0
isadmin># configure port nt-a:xfp:1 ethernet autonegotiate limited
isadmin># configure port nt-a:xfp:1 ethernet speed 1000
isadmin># configure port nt-a:xfp:1 no shutdown
isadmin># configure service vpls 110 customer 1 v-vpls vlan 110 create
isadmin># configure service vpls 110 description "IPTV"
isadmin># configure service vpls 110 sap nt-a:xfp:1:110 create
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 14 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
isadmin># configure service vpls 110 sap nt-a:xfp:1:110 igmp-snooping mrouter-port
isadmin># configure service vpls 110 sap lt:1/1/1:110 create
isadmin># configure service vpls 110 sap lt:1/1/1:110 igmp-snooping version 2
isadmin># configure service vpls 110 sap lt:1/1/1:110 igmp-snooping send-queries
isadmin># configure service vpls 110 igmp-snooping no shutdown
isadmin># configure service vpls 110 no shutdown
Create Multicast Channels:
isadmin># configure mcast chn 239.200.10.[1...10] src-ip-addr 0.0.0.0 vlan-id 20 guaranteed-serv peak-bit-rate 8000
Note: The bold part needs to be replaced by the actual value found on the node information sheet.
7.5 Create VLANs
Create VLANs on system and assign to all LTs and Uplink
HSI VLAN:
isadmin># configure vlan id 3210 mode residential-bridge name HSI new-broadcast enable
isadmin># configure vlan id stacked:1284:10 mode residential-bridge name HSI in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 3210 customer 1 v-vpls vlan 3210 create
isadmin># configure service vpls 3210 description "HSI"
isadmin># configure service vpls 3210 sap nt-a:xfp:1:3210 create
isadmin># configure service vpls 3210 sap lt:1/1/1:3210 create
isadmin># configure service vpls 3210 no shutdown
VoIP (SIP) VLAN:
isadmin># configure vlan id 2929 mode residential-bridge name SIP in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 2929 customer 1 v-vpls vlan 2898 create
isadmin># configure service vpls 2929 description "SIP"
isadmin># configure service vpls 2929 sap nt-a:xfp:1:2929 create
isadmin># configure service vpls 2929 sap lt:1/1/1:2929 create
isadmin># configure service vpls 2929 no shutdown
VoD VLAN:
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 15 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
isadmin># configure vlan id 111 mode residential-bridge name VoD in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 111 customer 1 v-vpls vlan 111 create
isadmin># configure service vpls 111 description "VoD"
isadmin># configure service vpls 111 sap nt-a:xfp:1:111 create
isadmin># configure service vpls 111 sap lt:1/1/1:111 create
isadmin># configure service vpls 111 no shutdown
Multicast VLAN:
isadmin># configure vlan id 110 mode residential-bridge name IPTV in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 110 customer 1 v-vpls vlan 110 create
isadmin># configure service vpls 110 description "IPTV"
isadmin># configure service vpls 110 sap nt-a:xfp:1:110 create
isadmin># configure service vpls 110 sap lt:1/1/1:110 create
isadmin># configure service vpls 110 no shutdown
Note: The bold part needs to be replaced by the actual value found on the node information sheet.
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 16 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
8 MDU Service Provisioning - Initial configuration
8.1 Create Vectoring Control Entity (VCE) Profile and associate it to a board
A non-null Vectoring Control Entity (VCE) profile should be associated to a board which is capable of processing the vectoring algorithms (Board Level Vectoring (BLV) board).
isadmin># configure xdsl vce-profile 1 name VCE_DEFAULT version 1 vce-join-timeout 20 active
isadmin># configure xdsl board 1/1/1 vce-profile 1
8.2 Create xDSL Vectoring Profiles
isadmin># configure xdsl vect-profile 1 name VECT_US_DS
isadmin>configure>xdsl>vect-profile>1$ version 1
isadmin>configure>xdsl>vect-profile>1$ active
isadmin>configure>xdsl>vect-profile>1$ exit
8.3 Create xDSL Service Profiles
Create xDSL Service Profiles.
isadmin># configure xdsl service-profile 1 name MaxUS_MaxDS_SRA_FAST
isadmin>configure>xdsl>service-profile>1$ version 1
isadmin>configure>xdsl>service-profile>1$ ra-mode-down dynamic
isadmin>configure>xdsl>service-profile>1$ ra-mode-up dynamic
isadmin>configure>xdsl>service-profile>1$ min-bitrate-down 32
isadmin>configure>xdsl>service-profile>1$ min-bitrate-up 32
isadmin>configure>xdsl>service-profile>1$ plan-bitrate-down 1024
isadmin>configure>xdsl>service-profile>1$ max-bitrate-down 262140
isadmin>configure>xdsl>service-profile>1$ max-bitrate-up 50000
isadmin>configure>xdsl>service-profile>1$ max-delay-down 2
isadmin>configure>xdsl>service-profile>1$ max-delay-up 2
isadmin>configure>xdsl>service-profile>1$ active
isadmin>configure>xdsl>service-profile>1$ exit
8.4 Create xDSL Spectrum Profiles
Create xDSL Spectrum Profiles.
isadmin># configure xdsl spectrum-profile 1 name VDSL2_noUPBO
isadmin>configure>xdsl>spectrum-profile>1$ version 1
isadmin>configure>xdsl>spectrum-profile>1$ dis-ansi-t1413
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 17 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
isadmin>configure>xdsl>spectrum-profile>1$ dis-etsi-dts
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-1-a
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-1-b
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-2-a
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-3-a
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-3-b
isadmin>configure>xdsl>spectrum-profile>1$ dis-etsi-ts
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8a
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8b
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8c
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8d
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-12a
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-12b
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-17a
isadmin>configure>xdsl>spectrum-profile>1$ max-noise-down 240
isadmin>configure>xdsl>spectrum-profile>1$ vdsl
isadmin>configure>xdsl>spectrum-profile>1>vdsl# vdsl-band-plan annex-b-998ade
isadmin>configure>xdsl>spectrum-profile>1>vdsl# optional-band up
isadmin>configure>xdsl>spectrum-profile>1>vdsl# optional-endfreq 138
isadmin>configure>xdsl>spectrum-profile>1>vdsl# adsl-band allow-adsl
isadmin>configure>xdsl>spectrum-profile>1>vdsl# max-band 8
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo-mode pbo-mode-down
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 1
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>1# param-a 4000
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>1# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 2
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# param-a 4730
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# param-b 1977
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 3
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# param-a 5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# param-b 1577
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 4
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 18 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# param-a 5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# param-b 1077
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 5
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# param-a 5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# param-b 943
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# exit
isadmin>configure>xdsl>spectrum-profile>1# vdsl2
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# propr-feat-value 2147483134
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# psd-shape-down regionbm2-psd-down
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# psd-shape-up regionbm2-psd-down
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# rx-psd-shape-up ab-param
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 1
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>1# param-a 4000
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>1# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 2
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# param-a 4730
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# param-b 1977
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 3
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# param-a 5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# param-b 1577
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 4
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# param-a 5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# param-b 1077
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 5
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 19 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# param-a 5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# param-b 943
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# exit
isadmin>configure>xdsl>spectrum-profile>1# active
isadmin>configure>xdsl>spectrum-profile>1# exit
8.5 Create xDSL Rtx Profiles
Create xDSL Rtx Profiles.
isadmin># configure xdsl rtx-profile 1 name ARQUSDS
isadmin>configure>xdsl>rtx-profile>1$ version 1
isadmin>configure>xdsl>rtx-profile>1$ min-exp-thrpt-dn 2000
isadmin>configure>xdsl>rtx-profile>1$ min-exp-thrpt-up 180
isadmin>configure>xdsl>rtx-profile>1$ plan-exp-thrpt-dn 20000
isadmin>configure>xdsl>rtx-profile>1$ plan-exp-thrpt-up 1024
isadmin>configure>xdsl>rtx-profile>1$ max-exp-thrpt-dn 131000
isadmin>configure>xdsl>rtx-profile>1$ max-exp-thrpt-up 50000
isadmin>configure>xdsl>rtx-profile>1$ max-net-rate-dn 131000
isadmin>configure>xdsl>rtx-profile>1$ max-net-rate-up 50000
isadmin>configure>xdsl>rtx-profile>1$ shine-ratio-dn 0
isadmin>configure>xdsl>rtx-profile>1$ shine-ratio-up 0
isadmin>configure>xdsl>rtx-profile>1$ active
isadmin>configure>xdsl>rtx-profile>1$ exit
8.6 Configure System Multicast for IPTV
Enable Multicast on System Level:
isadmin># configure mcast general fast-change
isadmin># configure mcast general package-member [1...1024]
isadmin># configure igmp system src-ip-address 10.88.43.222 start user-igmp-version 2 netw-igmp-version 2
isadmin># configure igmp shub igs-system start-snooping enable-snooping self-ip-addr-mode configure
Create Multicast VLAN:
isadmin># configure vlan shub id 110 mode residential-bridge name IPTV
isadmin># configure vlan shub id 110 egress-port lt:1/1/1
isadmin># configure vlan shub id 110 egress-port nt:sfp:1
isadmin># configure vlan id 110 mode residential-bridge name IPTV new-broadcast enable
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 20 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
Create Multicast Channels:
isadmin># configure qos cac-mode nocac
isadmin># configure mcast channel 239.1.1.[1...254] src-ip-addr 0.0.0.0 peak-bit-rate 1000 vlan-id 110
isadmin># configure mcast channel 239.1.2.[1...254] src-ip-addr 0.0.0.0 peak-bit-rate 1000 vlan-id 110
Note: The bold part needs to be replaced by the actual value found on the node information sheet.
8.7 Create VLANs
Create VLANs on system and assign to all LTs and Uplink
HSI VLAN:
isadmin># configure vlan shub id 3210 mode residential-bridge name HSI
isadmin># configure vlan shub id 3210 egress-port lt:1/1/1
isadmin># configure vlan shub id 3210 egress-port nt:sfp:1
isadmin># configure vlan id 3210 mode residential-bridge name HSI broadcast-frames
VoD VLAN:
isadmin># configure vlan shub id 111 mode residential-bridge name VoD user2-comm disable
isadmin># configure vlan shub id 111 egress-port lt:1/1/1
isadmin># configure vlan shub id 111 egress-port nt:sfp:1
isadmin># configure vlan id 111 mode residential-bridge name VoD broadcast-frames
Voice VLAN:
isadmin># configure vlan shub id 2929 mode voice-vlan name SIP
isadmin># configure vlan shub id 2929 egress-port lt:1/1/1
isadmin># configure vlan shub id 2929 egress-port nt:sfp:1
Note: The bold part needs to be replaced by the actual value found on the node information sheet.
8.8 Create VOIP Service
Create Voice(SIP) Service for connection to the softswitch.
isadmin># configure voice sip server sip1 address ipv4:10.0.0.110 admin-domain-name vsp1 admin-status up
isadmin># configure voice sip lineid-syn-prof profile1 pots-syntax random
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 21 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
isadmin># configure voice sip user-agent ua_01 ip-config-mode dhcp ip-addr-policy distributed signal-vlan-id 2929 rtp-vlan-id 2929 admin-status up
isadmin># configure voice sip transport udp provider-name vsp1 admin-status up
isadmin># configure voice sip register vsp1 register-uri telkom.net.id
isadmin># configure voice sip vsp vsp1 domain-name 10.0.0.110
isadmin># configure voice sip vsp vsp1 admin-status up
isadmin># configure voice sip user-agent-ap ua_01 slot-id lt:1/1/2 admin-status up
isadmin># configure voice sip dialplan dp1
isadmin># configure voice sip digitmap dp1 type regular rule x.T
isadmin># configure voice sip redundancy vsp1 bg-monitor-int 0
isadmin># configure voice sip system session-timer admin-status up
Note: The bold part needs to be replaced by the actual value found on the node information sheet.
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 22 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
9 Service Provisioning – Sample Service Configuration
9.1 Create SFP ONT Infrastructure
Create ONTs using SLID Password.
isadmin># configure equipment ont interface 1/1/1/1/1 sw-ver-pland 3FE55040AOPA21 sernum ALCL: FAB00CAC fec-up enable enable-aes enable
isadmin># configure equipment ont slot 1/1/1/1/1/1 planned-card-type 10_100base plndnumdataports 1 plndnumvoiceports 0 port-type nni admin-state up
isadmin># configure qos interface ont:1/1/1/1/1 us-num-queue 8
isadmin># configure interface port uni:1/1/1/1/1/1/1 no admin-up
isadmin># configure qos interface ont:1/1/1/1/1 scheduler-node name:NGLT_Default
9.2 Configure SFP ONT UNI
isadmin># configure interface port uni:1/1/1/1/1/1/1 admin-up
isadmin># configure qos interface 1/1/1/1/1/1/1 scheduler-node name:NGLT_Default
isadmin># configure qos interface 1/1/1/1/1/1/1 cac-profile name:FD_GponVideo
isadmin># configure qos interface 1/1/1/1/1/1/1 upstream-queue [0...7] weight 0 bandwidth-profile UP_1G bandwidth-sharing ont-sharing
isadmin># configure qos interface 1/1/1/1/1/1/1 queue [0…7] priority 1 weight 1
isadmin># configure bridge port /1/1/1/1/1/1 max-unicast-mac 2048
9.3 Create HSI Service on SFP ONT
Create HSI service on port 1 using HSI VLAN.
isadmin># configure bridge port 1/1/1/1/1/1/1 vlan-id 3210 tag single-tagged network-vlan 3210 vlan-scope local
9.4 Create VOD + Multicast Service on SFP ONT
Create VOD + Multicast Service using VOD VLAN.
isadmin># configure bridge port 1/1/1/1/1/1/1 vlan-id 111 tag single-tagged network-vlan 111 vlan-scope local
isadmin># configure igmp channel vlan:1/1/1/1/1/1/1:110 max-num-group 1024 max-msg-rate 256
9.5 Create VoIP Service on SFP ONT
Create VOIP services
isadmin># configure bridge port 1/1/1/1/1/1/1 vlan-id 2929 tag single-tagged network-vlan 2929 vlan-scope local
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 23 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
9.6 Create xDSL Vectored Line
Create xDSL Vectored Line.
isadmin># configure xdsl line 1/1/1/1 service-profile 1 spectrum-profile 1 rtx-profile 1 vect-profile 1 carrier-data-mode on transfer-mode ptm admin-up
9.7 Create HSI Service (RGW)
Create HSI service
isadmin># configure bridge port 1/1/1/1 max-unicast-mac 16
isadmin># configure bridge port 1/1/1/1 vlan-id 3210 tag single-tagged
isadmin># configure bridge port 1/1/1/1 pvid 3210
9.8 Create VOD + Multicast Service
Create VOD +Multicast service
isadmin># configure bridge port 1/1/1/1 max-unicast-mac 16
isadmin># configure bridge port 1/1/1/1 vlan-id 111 tag single-tagged
isadmin># configure igmp channel vlan:1/1/1/1:110 max-num-group 16
9.9 Create VoIP Service
Create VoIP service
isadmin># configure voice sip termination 1/1/2/1 directory-number +623151511024 user-name [email protected] uri [email protected] md5-realm telkom.net.id md5-password plain:telkom135 admin-status up
isadmin># configure voice sip termination 1/1/2/2 directory-number +623151511025 user-name [email protected] uri [email protected] md5-realm telkom.net.id md5-password plain:telkom135 admin-status up
10 Useful Show Commands
10.1 View vector disturbers on VDSL2 vectoring lines
View the actual mapping between the VP board and the SLV LT boards.
isadmin># show xdsl vect-disturbers 1/1/1/1 max-reported-dist 48
10.2 View the xDSL line status
View the xDSL line status.
isadmin># show xdsl operational-data line
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 24 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
View the mode of vectoring supported on CPE.
isadmin># show xdsl operational-data near-end line 1/1/1/1 detail
10.3 Show IGMP Statistics
Show IGMP statistics.
isadmin># show igmp channel counter
isadmin># show igmp channel miscellaneous
10.4 Show SIP Statistics
Show SIP statistics.
isadmin># show voice sip server
isadmin># show voice sip user-agent-ap
isadmin># show voice sip termination
10.5 Mirror on OLT
Mirroring on OLT.
isadmin># configure port nt-a:eth:1 ethernet autonegotiate limited
isadmin># configure port nt-a:eth:1 no shutdown
isadmin># debug mirror-source 1 port nt-a:xfp:1 egress ingress
isadmin># debug mirror-source 1 no shutdown
isadmin># configure mirror mirror-dest 1 sap nt-a:eth:1:0
isadmin># configure mirror mirror-dest 1
isadmin># info configure mirror
isadmin># show debug
10.6 Mirror on MDU
Mirroring on MDU.
isadmin># configure interface shub port nt:eth:1 port-type network admin-status auto-up
isadmin># configure interface shub mirror enable to-port nt:sfp:2
isadmin># configure interface shub mirror port nt:sfp:1 external ingress egress
isadmin># configure interface shub mirror port nt:sfp:1 internal ingress egress
isadmin># info configure interface shub mirror
11 Document History
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 25 of 26
All r
igh
ts r
eserv
ed
. P
assin
g o
n a
nd
cop
yin
g o
f th
is d
ocu
men
t,
use a
nd
com
mu
nic
ati
on
of
its c
on
ten
ts n
ot
perm
itte
d w
ith
ou
t w
ritt
en
au
thori
zati
on
fro
m A
lcate
l-Lu
cen
t.
Version Date Author(s) Description/Comment
0.1 June 24th 2014 Fiona Tay Document Creation
- END OF DOCUMENT -
Method of Procedure- 7356REM ISAM Turn-up Guide - Page 26 of 26