a5e02399122-01_bak_cp_5711_74
Post on 28-Oct-2015
31 Views
Preview:
DESCRIPTION
TRANSCRIPT
CP 5711
Betriebsanleitung (kompakt)Operating Instructions (Compact)
A5E02399122-01
s
SIMATIC NET
Dieses Dokument enthält Informationen in Deutsch.This document contains information in English.
Ausgabe/Release 02/2009
A5E02399122-01© SIEMENS AG 2009Änderungen vorbehaltenSubject to change
Sprachverzeichnis Deutsch ........................................................................................................ 3 English........................................................................................................ 34
CP 5711 A5E02399122-01, Ausgabe 02/2009 3
Rechtliche Hinweise Warnhinweiskonzept
Dieses Handbuch enthält Hinweise, die Sie zu Ihrer persönlichen Sicherheit sowie zur Vermeidung von Sachschäden beachten müssen. Die Hinweise zu Ihrer persönlichen Sicherheit sind durch ein Warndreieck hervorgehoben, Hinweise zu alleinigen Sachschäden stehen ohne Warndreieck. Je nach Gefährdungsstufe werden die Warnhinweise in abnehmender Reihenfolge wie folgt dargestellt.
GEFAHR bedeutet, dass Tod oder schwere Körperverletzung eintreten wird, wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
WARNUNG bedeutet, dass Tod oder schwere Körperverletzung eintreten kann, wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
VORSICHT mit Warndreieck bedeutet, dass eine leichte Körperverletzung eintreten kann, wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
VORSICHT ohne Warndreieck bedeutet, dass Sachschaden eintreten kann, wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
ACHTUNG bedeutet, dass ein unerwünschtes Ergebnis oder Zustand eintreten kann, wenn der entsprechende Hinweis nicht beachtet wird.
Beim Auftreten mehrerer Gefährdungsstufen wird immer der Warnhinweis zur jeweils höchsten Stufe verwendet. Wenn in einem Warnhinweis mit dem Warndreieck vor Personenschäden gewarnt wird, dann kann im selben Warnhinweis zusätzlich eine Warnung vor Sachschäden angefügt sein.
Rechtliche Hinweise
CP 5711 4 A5E02399122-01, Ausgabe 02/2009
Qualifiziertes Personal
Das zugehörige Gerät/System darf nur in Verbindung mit dieser Dokumentation eingerichtet und betrieben werden. Inbetriebsetzung und Betrieb eines Gerätes/Systems dürfen nur von qualifiziertem Personal vorgenommen werden. Qualifiziertes Personal im Sinne der sicherheitstechnischen Hinweise dieser Dokumentation sind Personen, die die Berechtigung haben, Geräte, Systeme und Stromkreise gemäß den Standards der Sicherheitstechnik in Betrieb zu nehmen, zu erden und zu kennzeichnen.
Bestimmungsgemäßer Gebrauch von Siemens-Produkten
Beachten Sie Folgendes:
WARNUNG Siemens-Produkte dürfen nur für die im Katalog und in der zugehörigen technischen Dokumentation vorgesehenen Einsatzfälle verwendet werden. Falls Fremdprodukte und -komponenten zum Einsatz kommen, müssen diese von Siemens empfohlen bzw. zugelassen sein. Der einwandfreie und sichere Betrieb der Produkte setzt sachgemäßen Transport, sachgemäße Lagerung, Aufstellung, Montage, Installation, Inbetriebnahme, Bedienung und Instandhaltung voraus. Die zulässigen Umgebungsbedingungen müssen eingehalten werden. Hinweise in den zugehörigen Dokumentationen müssen beachtet werden.
Marken
Alle mit dem Schutzrechtsvermerk ® gekennzeichneten Bezeichnungen sind eingetragene Marken der Siemens AG. Die übrigen Bezeichnungen in dieser Schrift können Marken sein, deren Benutzung durch Dritte für deren Zwecke die Rechte der Inhaber verletzen kann.
Haftungsausschluss
Wir haben den Inhalt der Druckschrift auf Übereinstimmung mit der beschriebenen Hard- und Software geprüft. Dennoch können Abweichungen nicht ausgeschlossen werden, so dass wir für die vollständige Übereinstimmung keine Gewähr übernehmen. Die Angaben in dieser Druckschrift werden regelmäßig überprüft, notwendige Korrekturen sind in den nachfolgenden Auflagen enthalten.
CP 5711 A5E02399122-01, Ausgabe 02/2009 5
Inhaltsverzeichnis Einleitung ................................................................................................................. 7
Beschreibung ........................................................................................................... 9
Lieferumfang..........................................................................................................9
Produktbeschreibung.............................................................................................9
Montage und Anschließen...................................................................................... 13
Montage des CP 5711 auf einer DIN 35mm-Hutschiene .....................................13
Anschließen .........................................................................................................15
Installieren der Software......................................................................................... 21
Installation des Treibers.......................................................................................21
Deinstallation des Treibers ..................................................................................21
Inbetriebnahme ...................................................................................................... 23
Projektierung des CP 5711..................................................................................23
Umstieg von CP 5512 auf CP 5711 .....................................................................23
Zulassungen und Zertifikate ................................................................................... 25
Technische Daten .................................................................................................. 29
Maßbild CP 5711 .................................................................................................33
Einleitung
CP 5711 A5E02399122-01, Ausgabe 02/2009 7
Einleitung Dokumentinhalt
Die vorliegende Betriebsanleitung (kompakt) umfasst Informationen mit denen Sie in der Lage sind, den Kommunikationsprozessor CP 5711 in Betrieb zu nehmen.
Weitere Informationen zum CP 5711 Dokumentbezeichnung Warum lesen?
Betriebsanleitung kompakt CP 5711
Sie werden schrittweise geführt, um den CP 5711 am PC zu installieren.
Projektierungshandbuch PC-Stationen in Betrieb nehmen
Sie erhalten die notwendigen Informationen zur Inbetriebnahme und Projektierung von SIMATC NET PROFIBUS Kommunikationsbaugruppen.
Handbücher ● SIMATIC NET Industrielle
Kommunikation mit PG/PC Band 1 – Grundlagen
● SIMATIC NET Industrielle Kommunikation mit PG/PC Band 2 – Schnittstellen
Das Handbuch führt in die Industrielle Kommunikation ein und erläutert die hierzu verfügbaren Kommunikationsprotokolle. Zusätzlich wird die OPC-Schnittstelle als Anwenderprogrammierschnittstelle beschrieben.
Installationsanleitung SIMATIC NET PC Software (Deutsch und Englisch)
Mit diesem Dokument erhalten Sie die Informationen, um die SIMATIC NET PC-Software-Produkte auf Ihrem PG/PC zu installieren.
Beschreibung
CP 5711 A5E02399122-01, Ausgabe 02/2009 9
Beschreibung
Lieferumfang Folgende Teile gehören zum Lieferumfang des CP 5711: ● Kommunikationsprozessor CP 5711 (Best. Nr. 6GK1571-1AA00) ● Vorliegende Betriebsanleitung (kompakt) für CP 5711 ● USB-Kabel (Best. Nr. 6GK1571-1AA00-0AD0) ● 24 V Stromversorgungsstecker ● Manual Collection DVD
Überprüfen Sie die Vollständigkeit der Lieferung. Setzen Sie sich bei unvollständiger Lieferung mit Ihrem Lieferanten oder der örtlichen Siemens-Geschäftsstelle in Verbindung.
Produktbeschreibung
Kommunikationsprozessor CP 5711
Der Kommunikationsprozessor CP 5711 hat folgende Produktmerkmale: ● Der CP 5711 ist mit einer PROFIBUS-Schnittstelle bis 12 Mbit/s ausgestattet. Er
ist für den Betrieb an PGs und PCs mit USB-Schnittstellen vorgesehen. ● Mit dem CP 5711 können bis zu 32 Geräte (PC, PG, SIMATIC S7 oder ET 200)
zu einem Netzsegment gekoppelt werden. Durch Kopplung mehrerer Segmente mit Repeatern sind maximal 127 Teilnehmer anschließbar.
● Die zusätzlichen Schnittstellensignale für die PLC Direktkopplung (PLC Programmable Logic Control) werden bis 187,5 kbit/s unterstützt.
MPI/DP-Netz
Die physikalische Kopplung der MPI/DP-Schnittstelle an das MPI/DP-Netz erfolgt über ein potentialgetrenntes RS485-Interface, das Bestandteil der Baugruppe ist. Im MPI/DP-Netz sind je nach Netzkonfiguration Datenübertragungsraten von 9,6 kbit/s bis maximal 12 Mbit/s möglich.
Hinweis Informationen zum Aufbau eines MPI-Netzes finden Sie im Handbuch "Aufbauen einer S7-300", Best. Nr. 6ES7030 0AA01-8AA0.
Beschreibung
CP 5711 10 A5E02399122-01, Ausgabe 02/2009
Statusleuchtdioden
Die CP 5711 Hardware bietet dem Anwender fünf LEDs zur Diagnose. Die LEDs haben folgende Beschriftung und Funktion:
Beschriftung Funktion PWR USB (grüne LED) LED an:
Der CP ist mit einem aktiven USB-Anschluss verbunden LED aus: Es besteht keine Verbindung zu einem aktiven USB-Anschluss
PWR EXT (grüne LED) LED aus: Am CP ist keine externe Spannungsversorgung angeschlossen; die Spannungsversorgung erfolgt ausschließlich über die aktive USB-Schnittstelle LED ein: zusätzliche Spannungsversorgung über die externe Spannungsquelle DC+24 V
LNK/SF (grün/rot LED) Die LED leuchtet grün, wenn Teilnehmer am PROFIBUS erkannt werden (Link-Status). Die LED leuchtet rot, wenn Fehler auf dem CP 5711 auftreten. Folgende Fälle können auftreten: ● Rote LED leuchtet ständig:
Der CP 5711 ist defekt. ● Rote LED blinkt schnell:
Exception-Zustand (unerwarteter Laufzeit-Fehler)
● Rote LED blinkt langsam: USB-Störung
● Rote LED blinkt zyklisch (3 mal schnell, lange Pause): Bus-Störung, mögliche Ursachen entnehmen Sie der Message-Box, die auf dem Bildschirm erscheint.
Wenn die LED weder grün noch rot leuchtet/blinkt, wurde vom CP 5711 kein BUS-Teilnehmer erkannt.
Beschreibung
CP 5711 A5E02399122-01, Ausgabe 02/2009 11
Beschriftung Funktion ACT (grüne LED) Diese LED blinkt, wenn der CP aktiv am
Datenverkehr teilnimmt. IDENT (grüne LED) Diese LED dient zur Identifizierung, um
den CP 5711 von anderen CPs im Rechner unterscheiden zu können. Über eine entsprechende Diagnosefunktion im Konfigurationstool "PG/PC-Schnittstelle einstellen" oder dem Komponenten-Konfigurator kann diese LED zu Testzwecken aktiviert werden (regelmäßiges Blinken).
Montage und Anschließen
CP 5711 A5E02399122-01, Ausgabe 02/2009 13
Montage und Anschließen
Montage des CP 5711 auf einer DIN 35mm-Hutschiene
WARNUNG Bei Einsatz in explosionsgefährdeter Umgebung entsprechend Class I, Division2 oder Class I, Zone 2 muss das Gerät in einen Schaltschrank oder in ein Gehäuse eingebaut werden. Um die EU-Richtlinie 94/9 (ATEX 95) zu erfüllen, muss das Gehäuse mindestens die Anforderungen von IP 54 nach EN 60529 erfüllt.
Hinweis Für die Montage des CP 5711 an einer Hutschiene ist eine Hutschienenhalterung erforderlich, Best. Nr. 6GK1571-1AA00-0AH0
Montage und Anschließen
CP 5711 14 A5E02399122-01, Ausgabe 02/2009
Vorgehensweise
A
B
C
Bild 3.1 Seitenansicht einer Hutschiene (grau dargestellt) mit einem
aufgesetzten CP 5711
Führen Sie folgende Schritte durch, um den CP 5711 auf einer Hutschiene zu montieren:
1. Montieren Sie die Hutschienenhalterung auf die Rückseite des CP 5711, indem Sie die Hutschienenhalterung in das vorgesehene Profil einschieben.
2. Setzen Sie den CP 5711 auf die Oberkante der Hutschiene (Position A). Dabei muss der PROFIBUS-Anschluss nach unten gerichtet sein.
3. Ziehen Sie den Hutschienenschieber (Position C) nach unten und drücken Sie den CP 5711 gegen die Hutschiene. Lassen Sie die Verriegelung des Hutschienenschiebers los, damit die Verriegelung bei Position B einrastet.
Montage und Anschließen
CP 5711 A5E02399122-01, Ausgabe 02/2009 15
Demontage des CP 5711 von der DIN 35mm-Hutschiene
Die Demontage des CP 5711 von der DIN 35mm-Hutschiene erfolgt in umgekehrter Reihenfolge wie die Montage.
Anschließen
WARNUNG Nehmen Sie nur unbeschädigte Teile in Betrieb!
Hinweis Anzahl möglicher CP 5711 an einem PC Es sind maximal zwei CP 5711 an einem PG/PC zulässig. Dabei darf sich nur ein CP 5711 im projektierten Zustand befinden.
A
B C
D
A PROFIBUS-Schnittstelle B USB-Schnittstelle C externe Spannungsversorgung D Masse-Anschluss
Montage und Anschließen
CP 5711 16 A5E02399122-01, Ausgabe 02/2009
WARNUNG Bei Einsatz in explosionsgefährdeter Umgebung entsprechend Class I, Division 2 oder Class I, Zone 2 muss das Gerät in einen Schaltschrank oder in ein Gehäuse eingebaut werden. Um die EU-Richtlinie 94/9 (ATEX 95) zu erfüllen, muss das Gehäuse mindestens die Anforderungen von IP 54 nach EN 60529 erfüllt.
WARNUNG Wenn am Kabel oder an der Gehäusebuchse Temperaturen über 70° C auftreten oder die Temperatur an den Adernverzweigungsstellen der Leitungen über 80° C liegt, müssen besondere Vorkehrungen getroffen werden. Wenn das Gerät bei einer Umgebungstemperatur von 0° C - 60° C betrieben wird, müssen Sie Kabel mit einer zulässigen Betriebstemperatur von mindestens 80° C verwenden.
WARNUNG Treffen Sie Maßnahmen, um transiente Überspannungen von mehr als 40% der Nennspannung zu verhindern. Das ist gewährleistet, wenn Sie die Geräte ausschließlich mit SELV (Sicherheitskleinspannung) betreiben.
WARNUNG EXPLOSIONSGEFAHR IN EINER LEICHT ENTZÜNDLICHEN ODER BRENNBAREN UMGEBUNG DÜRFEN KEINE LEITUNGEN AN DAS GERÄT ANGESCHLOSSEN ODER VOM GERÄT GETRENNT WERDEN.
WARNUNG EXPLOSIONSGEFAHR DER AUSTAUSCH VON KOMPONENTEN KANN DIE EIGNUNG FÜR CLASS I, DIVISION 2, ODER CLASS I, ZONE 2 BEEINTRÄCHTIGEN.
WARNUNG EXPLOSIONSGEFAHR ÖFFNEN SIE DAS GERÄT NICHT BEI EINGESCHALTETER VERSORGUNGSSPANNUNG.
Montage und Anschließen
CP 5711 A5E02399122-01, Ausgabe 02/2009 17
Vorgehensweise beim Anschließen
1. Verbinden Sie die USB-Schnittstellen des CP 5711 und des PC mit dem USB-Kabel. Verwenden Sie dafür nur das mitgelieferte oder ein anderes industrietaugliches USB-Kabel.
Hinweis
Verwenden Sie vorzugsweise die USB-Anschlüsse an Ihrem PC, die sich hinten am Gehäuse befinden, um den CP 5711 und den PC miteinander zu verbinden. Die USB-Frontanschlüsse haben im allgemeinen eine geringere Signalqualität. Es wird empfohlen keine zusätzlichen USB-Hubs zu verwenden.
ACHTUNG
USB 1.1 und USB 2.0 Um das zugesicherte Mengengerüst bei allen Protokollen und Busgeschwindigkeiten zu erreichen, verwenden Sie vorzugsweise einen USB 2.0 Highspeed-Anschluss. Sie können bei "PC-Station einstellen" unter "CP 5711 → USB-Anschluss → USB-Version" überprüfen, welche USB-Version der USB-Port an Ihrem PC verwendet.
2. Verbinden Sie den CP 5711 über die PROFIBUS-Schnittstelle mit dem PROFIBUS.
Vorgehensweise beim Entfernen des CP 5711 bei laufendem Betriebssystem
ACHTUNG Bestehende Projektierungen des CP 5711 müssen vor dem Entfernen gelöscht werden. Dies können Sie z. B. mit dem Komponenten-Konfigurator oder in "PC-Station einstellen" vornehmen. Bevor der CP 5711 vom PC/PG entfernt werden kann, muss er auf eine sichere Art vom PC/PG abgemeldet werden. Klicken Sie hierfür das Symbol "Hardware sicher entfernen" im Infobereich der Taskleiste.
Montage und Anschließen
CP 5711 18 A5E02399122-01, Ausgabe 02/2009
Externe Spannungsversorgung
ACHTUNG Wird der CP 5711 über ausgedehnte 24V-Versorgungsleitungen oder Netze gespeist, sind Maßnahmen gegen Einkopplung starker elektromagnetischer Pulse auf die Versorgungsleitungen erforderlich. Diese können z. B. durch Blitzschlag oder Schalten großer induktiver Lasten entstehen. Die Robustheit des CP 5711 gegen elektromagnetische Störungen wird unter anderem mit der Prüfung "Surge Immunity Test" nach EN61000-4-5 nachgewiesen. Bei dieser Prüfung ist ein Überspannungsschutz für die Spannungsversorgungsleitung erforderlich. Geeignet ist z. B. der Dehn Blitzductor BVT AD 24V Art. Nr. 918 402 oder ein gleichwertiges Schutzelement. Hersteller: DEHN+SÖHNE GmbH+Co.KG, Hans Dehn Str. 1, Postfach 1640, D-92306 Neumarkt
WARNUNG Das Gerät ist für den Betrieb mit einer direkt anschließbaren Sicherheitskleinspannung (Safety Extra-Low Voltage, SELV) durch eine Spannungsversorgung mit begrenzter Leistung (Limited Power Source, LPS) ausgelegt. Deshalb dürfen nur Sicherheitskleinspannungen (SELV) mit begrenzter Leistung (LPS) nach IEC 60950-1 / EN 60950-1 / VDE 0805-1 mit den Versorgungsanschlüssen verbunden werden oder das Netzteil für die Versorgung des Geräts muss NEC Class 2 gemäß National Electrical Code (r) (ANSI / NFPA 70) entsprechen. Zusätzlich bei Geräten mit redundanter Spannungsversorgung: Wenn das Gerät an eine redundante Spannungsversorgung angeschlossen wird (zwei getrennte Spannungsversorgungen), müssen beide die genannten Anforderungen erfüllen.
Montage und Anschließen
CP 5711 A5E02399122-01, Ausgabe 02/2009 19
Der CP 5711 kann zusätzlich durch eine externe Spannungsversorgung mit 24 Volt betrieben werden. Diese zusätzliche externe Spannungsversorgung benötigen Sie in folgenden Fällen: ● Der CP 5711 wird an einem externen Hub ohne eigene Stromversorgung
betrieben. ● Die USB-Schnittstelle am PC ist eine Low-Power-Schnittstelle und liefert somit
nur 100 mA. ● Am Profibus-Stecker kann die Endterminierung eingeschaltet werden, wenn der
CP 5711 sich an einem Leitungsende befindet. Soll diese Terminierung auch dann wirksam sein, wenn kein USB-Kabel angeschlossen ist, ist eine externe Spannungsversorgung erforderlich.
VORSICHT
Gerät von der externen Spannungsversorgung trennen Wenn Sie das Gerät von der externen Spannungsversorgung trennen wollen, gehen Sie wie folgt vor: 1. Beenden Sie jede über den CP 5711 laufende Kommunikation. 2. Trennen Sie die USB-Verbindung des Gerätes zum PC. 3. Trennen Sie die externe Spannungsversorgung vom Gerät.
Parallelbetrieb mit anderen USB-Geräten
ACHTUNG Die Verwendungen von weiteren USB-Geräten (z.B. Webcam, Massenspeicher, ...) an USB-Ports des PC kann Auswirkungen auf die Performance des CP 5711 haben.
ACHTUNG Ziehen und Stecken von USB-Geräten kann zu Funktionsstörungen der USB-Schnittstelle führen. Im Extremfall kann dadurch die Kommunikation über den CP 5711 abbrechen, sodass ein Neustart der Anwendung notwendig ist.
Hinweis Verwenden Sie beim gleichzeitigen Betrieb von zwei CP 5711 an einem Rechner unterschiedliche Root-Hubs.
Installieren der Software
CP 5711 A5E02399122-01, Ausgabe 02/2009 21
Installieren der Software
Installation des Treibers
Voraussetzung
Folgende Voraussetzung muss erfüllt sein:
Der USB-Controller ist im BIOS des Rechners aktiviert.
Installation des CP 5711-Treibers
Der Treiber wird automatisch installiert, wenn Sie die CD "SIMATIC NET, PC Software" mit CD 2008 + SP1 installieren.
Der CP 5711 wird mit der CD "SIMATIC NET, PC Software, Edition 2008 + SP1" unterstützt.
Die für den CP 5711 freigegebene STEP 7-Version entnehmen Sie der Liesmich-Datei von STEP 7.
Deinstallation des Treibers
Deinstallation des CP 5711-Treibers
Der Treiber wird automatisch deinstalliert, wenn Sie die CD "SIMATIC NET, PC Software" oder STEP 7 deinstallieren. Sollten Sie beide Software-Programme installiert haben und nur eines davon deinstallieren, bleibt der Treiber installiert.
Hinweis Beachten Sie zur Deinstallation von STEP 7 folgende Hinweise in Deutsch: http://support.automation.siemens.com/ww/view/de/189025 Englisch: http://support.automation.siemens.com/ww/view/en/189025
Inbetriebnahme
CP 5711 A5E02399122-01, Ausgabe 02/2009 23
Inbetriebnahme
Projektierung des CP 5711 Erstellen Sie mit NCM PC (im Lieferumfang der SIMATIC NET CD enthalten) oder STEP 7 eine passende Projektierung für den CP 5711.
Sollte der CP 5711 sich nicht im Hardware-Katalog von STEP 7 oder NCM PC befinden, können Sie im Projekt auch einen CP 5512 verwenden, die Projektierung des CP 5711 ist abwärtskompatibel zum CP 5512.
Umstieg von CP 5512 auf CP 5711 Der CP 5711 kann mit der Projektierung eines CP 5512 betrieben werden.
Hinweis Das System gibt einem CP 5512 immer den Vorzug. Daher müssen Sie eine vorhandene CP 5512-Baugruppe und deren Projektierung vor dem Umstieg aus der PC-Station entfernen.
Falls ein CP 5512 vorhanden ist führen Sie folgende Schritte aus:
1. Löschen Sie die projektierte Baugruppe aus dem Komponenten-Konfigurator, wenn der CP 5512 projektiert ist.
2. Entfernen Sie die Hardware CP 5512 aus dem PC.
3. Starten Sie Ihren PC neu.
4. Schließen Sie den CP 5711 an Ihren PC an und installieren Sie der Treiber.
5. Konfigurieren Sie den CP 5711.
6. Laden Sie die CP 5512-Projektierung.
Hinweis Wenn ein CP 5512 physikalisch nicht vorhanden ist, akzeptiert das System den CP 5711 als Ersatz. Das System wird allerdings darauf hinweisen, dass es sich bei der Zielbaugruppe um keinen CP 5512 handelt.
Zulassungen und Zertifikate
CP 5711 A5E02399122-01, Ausgabe 02/2009 25
Zulassungen und Zertifikate Elektromagnetische Verträglichkeit
Das SIMATIC NET-Produkt erfüllt die Anforderungen der EG-Richtlinie: 2004/108/EG "Elektromagnetische Verträglichkeit"
Der Kommunikationsprozessor ist ausgelegt für den Einsatz in folgenden Bereichen: Anforderungen an Einsatzbereich
Störaussendung Störfestigkeit Wohnbereich, Geschäfts- und Gewerbebereich sowie Kleinbetriebe
EN 61000-6-3 EN 61000-6-1
Industriebereich EN 61000-6-4 EN 61000-6-2
Aufbaurichtlinien beachten
Der Kommunikationsprozessor erfüllt die Anforderungen, wenn Sie bei Installation und Betrieb die Aufbaurichtlinien und Sicherheitshinweise einhalten, die in dieser Beschreibung sowie im "PROFIBUS Netzhandbuch" beschrieben sind.
Arbeiten am Produkt
Zum Schutz des Kommunikationsprozessors vor Entladung von statischer Elektrizität muss sich das Bedienpersonal vor dem Berühren der Baugruppe elektrostatisch entladen.
Hinweis Der Kommunikationsprozessor wurde mit einem Gerät getestet, das ebenfalls die oben genannten Normen einhält. Beim Betrieb des Kommunikationsprozessors mit einem Gerät, das diese Normen nicht erfüllt, kann die Einhaltung der entsprechenden Werte nicht garantiert werden.
Zulassungen und Zertifikate
CP 5711 26 A5E02399122-01, Ausgabe 02/2009
Konformitätserklärung
Die EG-Konformitätserklärung zu diesem Kommunikationsprozessor finden Sie im Internet unter folgender Adresse:
http://supportauthoring.automation.siemens.com → Abschnitt Selbsthilfe; geben Sie dort "EG-Konformitätserklärung" und den Produktnamen ein; Beispiel deutsch: "EG-Konformitätserklärung CP 5711", Beispiel englisch: "Declaration of Conformity CP 5711".
Maschinenrichtlinie
Der Kommunikationsprozessor ist keine Maschine im Sinne der EG-Richtlinie Maschinen. Es gibt deshalb für den Kommunikationsprozessor keine Konformitätserklärung bezüglich der EG-Richtlinie Maschinen 2006/42/EG.
Ist der Kommunikationsprozessor Teil der Ausrüstung einer Maschine, muss er vom Maschinenhersteller in das Verfahren zur Konformitätserklärung einbezogen werden.
Hinweis für Australien (C-TICK)
Der Kommunikationsprozessor erfüllt die Anforderungen der Norm AS/NZS 3548.
CSA-Zulassung
Der Kommunikationsprozessor verfügt über eine Zulassung nach Standard CAN/CSA C22.2 No. 60950-1.
ATEX-, cULus- und FM-Zulassung
Der Kommunikationsprozessor verfügt über folgende Zulassungen: ● EN 60079-15:2005
EN 60079-0:2006 II 3 G Ex nA II T.. KEMA 07 ATEX 0145
● c-UL-us: UL 60950-1 CSA C22.2 No. 60950-1
● FM 3611 Hazardous (Classified) Location Electrical Equipment: Non Incendive / Class I / Division 2 / Groups A,B,C,D / T* and Non Incendive / Class I / Zone 2 / Group IIC / T*
● c-UL-us for hazardous location*: ISA 12.12.01-2000, CSA C22.2 No. 213-M1987 CL. 1, Div. 2 GP. A.B.C.D T.. CL. 1, Zone 2, GP, IIC, T.. CL. 1, Zone 2, AEx nC IIC T..
(T.. / T* = Konkrete Angaben zur Temperaturklasse finden Sie auf dem Typenschild)
Zulassungen und Zertifikate
CP 5711 A5E02399122-01, Ausgabe 02/2009 27
FCC-Zulassung
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help.
Siemens AG is not responsible for any radio television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Siemens AG. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.
Hinweis Die angegebenen Zulassungen gelten erst dann als erteilt, wenn auf dem Kommunikationsprozessor eine entsprechende Kennzeichnung angebracht ist.
Technische Daten
CP 5711 A5E02399122-01, Ausgabe 02/2009 29
Technische Daten Folgende technische Daten gelten für den Kommunikationsprozessor CP 5711: Konstruktiver Aufbau Maße (H x B x T) in mm 137 x 85 x 35 Gewicht ca. 255 g Baugruppen-Steckprinzip USB
Spannung Betriebsspannung optionales Netzteil
Imax = 300 mA V = 24 V
Stromaufnahme max. 500 mA (USB)
Datenübertragung Übertragungsgeschwindigkeit 9,6 kbit/s bis 12 Mbit/s
Schnittstellen Anschluss an PG/PC USB V2.0, kompatibel zu V1.1 Steckverbinder 9-polige D-SUB-Buchsenleiste mit
Schraubverriegelung USB-Buchse Typ B mit Verriegelung
Übertragungsart RS 485 erdfrei innerhalb der SELV-Grenzen
Betriebsart der PROFIBUS-Schnittstelle Potentialfrei (Schnittstellensignale), erdgebunden (Leitungsschirm)
Technische Daten
CP 5711 30 A5E02399122-01, Ausgabe 02/2009
Elektromagnetische Verträglichkeit (EMV) Störaussendung Klasse B nach EN 55022
FCC Klasse B Störfestigkeit auf Signalleitungen (nur PROFIBUS)
+/- 2 kV nach IEC 61000-4-5, Surge +/- 1 kV nach IEC 61000-4-4, Burst
Störfestigkeit gegen Entladen statischer Elektrizität
+/- 6 kV, Contact discharge nach IEC 61000-4-2
Störfestigkeit gegen Hochfrequenzeinstrahlung
● 10 V/m bei 80 MHz – 2 GHz nach IEC 61000-4-3
● 10 V/m mit 80 % Amplitudenmodulation mit 1 kHz
● 10 kHz – 80 MHz nach IEC 61000-4-6
Sicherheit UL/CSA-Zulassung Der CP 5711 erfüllt alle Anforderungen
an Zusatzbaugruppen gemäß Zulassung cULus.
Mechanische Umgebungsbedingungen Betriebsschwingung Geprüft nach EN 60068 2 6: 10 bis 58
Hz, Amplitude: 0,075 mm, 58 bis 500 Hz; Beschleunigung: 10 m/s2, 10 Zyklen/Achse
Betriebsschocken Geprüft nach EN 60068 2 27; Halbsinus: 50 m/s2 (5 g), 30 ms, 100 Schocks/Achse
Klimatische Bedingungen Temperatur (Betrieb) Geprüft nach IEC 60068 2 1, 60068-2-2:
0 °C bis +60 °C, Temperaturänderung: max. 10 K/h
Transport- und Lagertemperatur -40 bis +70 °C, Temperaturänderung: max. 20 K/h
Technische Daten
CP 5711 A5E02399122-01, Ausgabe 02/2009 31
Klimatische Bedingungen Feuchte (Betrieb) Geprüft nach EN/IEC 60068-2-78:
95 % / 16h bei 30 °C (keine Betauung) Rascher Temperaturwechsel im Betrieb Geprüft nach IEC 60068-2-14:
0 °C / 3h; +60 °C / 3h, 5 Zyklen Rascher Temperaturwechsel bei Lagerung/Transport
Geprüft nach IEC 60068-2-14: -40 bis +70 °C, 2 Zyklen
Temperaturwechsel bei Feuchte bei Lagerung/Transport
Geprüft nach EN/IEC 60068-2-30: 25 bis 55 °C bei 97 % (keine Betauung)
Belegung der PROFIBUS-Schnittstelle
Die SUB D-Buchsenleiste ist wie folgt belegt:
5 4 3 2 1
9 8 7 6
Bild 7.1 Pin-Belegung der SUB-D-Buchse (weiblich)
Technische Daten
CP 5711 32 A5E02399122-01, Ausgabe 02/2009
PIN-Nr.
Kurz- bezeichnung
Bedeutung Eingang/ Ausgang
1 NC Buchse Pin 1 ist nicht beschaltet. - 2 NC (M24) Buchse Pin 2 ist nicht beschaltet. Bei
anderen PROFIBUS-Komponenten kann auf diesem Pin der Rückleiter der potentialfreien 24 V-Versorgung liegen.
-
3 LTG_B Signalleitung B des PROFIBUS Ein-/Ausgang 4 RTSAS RTSAS, Eingangssignal für MPI-
Direktkopplung. Das Steuersignal ist "1"-aktiv, wenn das über ein MPI-Spezialkabel angeschlossene Automatisierungsgerät sendet.
Eingang
5 M5EXT M5EXT Rückleiter (GND) der 5 V-Versorgung. Die Strombelastung durch einen externen Verbraucher, der zwischen P5EXT und M5EXT angeschlossen wird, darf max. 20 mA betragen.
Ausgang
6 P5EXT P5EXT Versorgung (+5 V). Die Strombelastung durch einen externen Verbraucher, der zwischen P5EXT und M5EXT angeschlossen wird, darf für den Betrieb der Terminierung max. 20 mA betragen (kurzschlussfest).
Ausgang
7 NC (P24V) Buchse Pin 7 ist nicht beschaltet. Bei anderen PROFIBUS-Komponenten kann auf diesem Pin die Versorgung P24V der potentialfreien 24 V-Versorgung liegen.
-
8 LTG_A Signalleitung A des PROFIBUS Ein-/Ausgang 9 RTS RTS Ausgangssignal der CP 5711-
Baugruppe. Das Steuersignal ist "1"-aktiv, wenn der CP 5711 sendet.
Ausgang
Schirm Schirm liegt auf Steckergehäuse, PROFIBUS-Schirm und USB-Schirm sind galvanisch verbunden.
Technische Daten
CP 5711 A5E02399122-01, Ausgabe 02/2009 33
Maßbild CP 5711
Vorderansicht und Draufsicht CP 5711
s
CP 5711
PW
R U
SB
PW
R E
XT
AC
T
LNK
/SF
IDE
NT
85
137
35
Alle Angaben in Millimeter.
CP 5711 34 A5E02399122-01, Release 02/2009
Legal notices Concept of the warning notices
This manual contains notices which you should observe to ensure your own personal safety, as well as to protect the product and connected equipment. Notices relating to your personal safety are highlighted by a warning triangle; notices relating to property damage only do not have a warning triangle. Warnings in descending order according to the degree of danger are shown as follows.
DANGER indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING indicates that death or severe personal injury can result if proper precautions are not taken.
CAUTION with a warning triangle indicates that minor personal injury can result if proper precautions are not taken.
CAUTION without a warning triangle indicates that damage to property can result if proper precautions are not taken.
NOTICE indicates that an undesirable result or status can occur if the relevant notice is ignored.
If more than one degree of danger is present, the notice representing the highest degree of danger will be used. A notice warning of injury to persons with a warning triangle may also include a warning relating to property damage.
Legal notices
CP 5711 A5E02399122-01, Release 02/2009 35
Qualified personnel
The device/system described here must only be set up and operated in conjunction with this documentation. Only qualified personnel should be allowed to install and work on this equipment/system. Qualified persons in the sense of the safety-related notices in this documentation are defined as persons who are authorized to commission, to ground, and to tag circuits, equipment, and systems in accordance with established safety practices and standards.
Correct usage of Siemens products
Note the following:
WARNING Siemens products may only be used for the applications indicated in the catalog and in the relevant technical documentation. If third-party products and components are used, these must be recommended or approved by Siemens. These products can only function correctly and safely if they are transported, stored, set up, mounted, installed, commissioned, operated and maintained correctly. The permitted environmental and ambient conditions must be adhered to. Notices in the relevant documentation must be observed.
Trademarks
All names shown with the trademark symbol ® are registered trademarks of Siemens AG. Third parties using for their own purposes any other names in this document which refer to trademarks might infringe upon the rights of the trademark owners.
Disclaimer of liability
We have checked the contents of this manual for agreement with the hardware and software described. Since deviations cannot be precluded entirely, we cannot guarantee full agreement. However, the data in this manual are reviewed regularly and any necessary corrections included in subsequent editions.
CP 5711 A5E02399122-01, Release 02/2009 37
Table of contents Introduction ............................................................................................................ 39
Description ............................................................................................................. 41
Components of the product..................................................................................41
Description of the product ....................................................................................41
Installing and connecting up ................................................................................... 45
Mounting the CP 5711 on a 35 mm DIN rail ........................................................45
Connecting up......................................................................................................47
Installing the software............................................................................................. 53
Installing the driver...............................................................................................53
Uninstalling the driver ..........................................................................................53
Commissioning....................................................................................................... 55
Configuring the CP 5711......................................................................................55
Changing from CP 5512 to CP 5711 ...................................................................55
Approvals and certificates....................................................................................... 57
Technical specifications.......................................................................................... 61
CP 5711 dimension drawing ................................................................................65
Introduction
CP 5711 A5E02399122-01, Release 02/2009 39
Introduction Content of the document
These compact operating instructions contain information with which you will be in a position to install and commission the CP 5711 communications processor.
Further information on the CP 5711 Name of the documentation Why you should read it
Operating Instructions compact CP 5711
You are guided step-by-step through the installation of the CP 5711 on the PC.
Configuration Manual Commissioning PC Stations
This provides you with the information required to commission and configure a SIMATIC NET PROFIBUS communications module.
Manuals ● SIMATIC NET Industrial
Communication with PG/PC Part 1 - Basics
● SIMATIC NET Industrial Communication with PG/PC Part 2 - Interfaces
This manual introduces you to industrial communication and explains the available communication protocols. There is also a description of the OPC interface as user programming interface.
Installation Manual SIMATIC NET PC Software (German and English)
This document provides you with the information required to install the SIMATIC NET PC software products on your PG/PC.
Description
CP 5711 A5E02399122-01, Release 02/2009 41
Description
Components of the product The following parts make up the components of the CP 5711 product: ● Communications processor CP 5711 (order no. 6GK1571-1AA00) ● These Operating Instructions (compact) for CP 5711 ● USB cable (order no. 6GK1571-1AA00-0AD0) ● 24 V power supply connector ● Manual Collection DVD
Please check that the consignment you have received is complete. If the consignment is incomplete, contact your supplier or your local Siemens office.
Description of the product
CP 5711 communications processor
The CP 5711 communications processor has the following product characteristics: ● The CP 5711 is equipped with a PROFIBUS interface allowing up to 12 Mbps. It
is intended for operation in programming devices and PCs with USB interfaces. ● With the CP 5711, up to 32 devices (PC, PG, SIMATIC S7 or ET 200) can be
linked to form a network segment. By linking several segments with repeaters, a maximum of 127 nodes can be connected.
● The additional interface signals for the PLC direct link (PLC Programmable Logic Controller) are supported up to 187.5 kbps.
MPI/DP network
The physical link between the MPI/DP interface and the MPI/DP network is via a floating RS-485 interface that is part of the module. Depending on the network configuration, data rates of 9.6 kbps up to a maximum of 12 Mbps are possible in the MPI/DP network.
Note For information on setting up an MPI network, refer to the manual "S7-300", Hardware and Installation, order no. 6ES7030 0AA01-8BA0.
Description
CP 5711 42 A5E02399122-01, Release 02/2009
Status LEDs
CP 5711 hardware provides the user with five LEDs for diagnostics. The LEDs have the following labeling and function:
Labeling Function PWR USB (green LED) LED on:
The CP is connected to an active USB connector LED off: There is no connection to an active USB connector
PWR EXT (green LED) LED off: An external power supply is connected to the CP; the power supply is solely via the active USB interface LED on: Additional power supply via the external power source +24 V DC
LNK/SF (green/red LED) The LED is lit green when nodes are detected on PROFIBUS (link status). The LED is lit red if errors occur on the CP 5711. The following situations can arise: ● LED lit red permanently:
The CP 5711 is defective. ● LED flashes red quickly:
Exception status (unexpected runtime error)
● LED flashes red slowly: USB problem
● LED flashes red cyclically (3 times fast, long break): Bus problem You will find the possible causes in the message box that appears on the screen.
If the LED is neither lit/flashes red nor green, the CP 5711 has not detected a BUS node.
Description
CP 5711 A5E02399122-01, Release 02/2009 43
Labeling Function ACT (green LED) This LED flashes when the CP is
actively involved in data traffic. IDENT (green LED) This LED is used to identify the CP 5711
and to distinguish it from other CPs in the computer. Using a suitable diagnostics function in the "Set PG/PC Interface" configuration tool or the Station Configuration Editor, this LED can be activated for test purposes (flashes regularly).
Installing and connecting up
CP 5711 A5E02399122-01, Release 02/2009 45
Installing and connecting up
Mounting the CP 5711 on a 35 mm DIN rail
WARNING When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2, the device must be installed in a cabinet or a suitable enclosure. To comply with EU-Directive 94/9 (ATEX95), this enclosure must meet the requirements of at least IP54 in compliance with EN 60529.
Note To install the CP 5711 on a DIN rail, a DIN rail holder is required, order no. 6GK1571-1AA00-0AH0
Installing and connecting up
CP 5711 46 A5E02399122-01, Release 02/2009
Procedure
A
B
C
Figure 3.1 Side view of a DIN rail (shown in gray) with a CP 5711 fitted
Follow the steps below to fit the CP 5711 to a DIN rail:
1. Fit the DIN rail holder to the back of the CP 5711 by pushing the DIN rail holder into the profile provided.
2. Place the CP 5711 on the upper edge of the DIN rail (position A). The PROFIBUS connector must be pointing down.
3. Pull the DIN rail slider (position C) down and press the CP 5711 against the DIN rail. Release the catch of the DIN rail slider so that the catch locks in place at position B.
Installing and connecting up
CP 5711 A5E02399122-01, Release 02/2009 47
Removing the CP 5711 from the 35 mm DIN rail
To remove the CP 5711 from the 35 mm DIN rail, follow the procedure above in the opposite order.
Connecting up
WARNING Do not use any parts that show evidence of damage!
Note Number of possible CP 5711 modules connected to one PC A maximum of two CP 5711 modules can be used with one PG/PC. However, only one CP 5711 may be in the configured status.
A
B C
D
A PROFIBUS interface B USB interface C external power supply D chassis ground connection
Installing and connecting up
CP 5711 48 A5E02399122-01, Release 02/2009
WARNING When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2, the device must be installed in a cabinet or a suitable enclosure. To comply with EU-Directive 94/9 (ATEX95), this enclosure must meet the requirements of at least IP54 in compliance with EN 60529.
WARNING If the cable or conduit entry point exceeds 70 °C or the branching point of conductors exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air ambient of 0 °C - 60 °C, only use cables with admitted maximum operating temperature of at least 80 °C.
WARNING Provisions shall be made to prevent the rated voltage from being exceeded by transient voltage surges of more than 40%. This criterion is fulfilled, if supplies are derived from SELV (Safety Extra-Low Voltage) only.
WARNING EXPLOSION HAZARD DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR COMBUSTIBLE ATMOSPHERE IS PRESENT.
WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2 OR ZONE 2.
WARNING EXPLOSION HAZARD DO NOT OPEN WHEN ENERGIZED.
Installing and connecting up
CP 5711 A5E02399122-01, Release 02/2009 49
Procedure for connecting up
1. Connect the USB interfaces of the CP 5711 and the PC with the USB cable. Use only the USB cable supplied or another USB cable suitable for use in industry.
Note
Ideally, you should use the USB connectors on the back of the housing of your PC to connect the CP 5711 and PC. The front USB connectors generally have a lower signal quality. We recommend that you do not use any additional USB hubs.
NOTICE
USB 1.1 and USB 2.0 To achieve the guaranteed configuration limits with all protocols and at all bus transmission speeds, you should ideally use a USB 2.0 high-speed connector. In the "Configuration Console", you can check which USB version the USB port is used on your PC "CP 5711 → USB connector → USB version".
2. Connect the CP 5711 with PROFIBUS via the PROFIBUS interface.
Procedure for removing the CP 5711 while the operating system is running
NOTICE Existing configurations of the CP 5711 must be deleted before it is removed. You can do this, for example, in the Station Configuration Editor or in the "Configuration Console". Before you can remove the CP 5711 from the PC/PG it must be disconnected safely from the PC/PG. Click the "Safely Remove Hardware" icon in the taskbar notification area.
Installing and connecting up
CP 5711 50 A5E02399122-01, Release 02/2009
External power supply
NOTICE If the CP 5711 is supplied over long 24 V power supply lines or networks, measures are necessary to prevent interference by strong electromagnetic pulses on the supply lines. These can result, for example, due to lightning or switching of large inductive loads. One of the tests used to attest the immunity of the CP 5711 to electromagnetic interference was the "surge immunity test" according to EN61000-4-5. This test requires overvoltage protection for the power supply line. A suitable device is, for example, the Dehn Blitzductor BVT AD 24 V type no. 918 402 or comparable protective element. Manufacturer; DEHN+SÖHNE GmbH+Co.KG, Hans Dehn Str. 1, Postfach 1640, D-92306 Neumarkt, Germany
WARNING The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a Limited Power Source (LPS). This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1 must be connected to the power supply terminals. The power supply unit for the equipment power supply must comply with NEC Class 2, as described by the National Electrical Code (r) (ANSI / NFPA 70). There is an additional requirement if devices are operated with a redundant power supply: If the equipment is connected to a redundant power supply (two separate power supplies), both must meet these requirements.
The CP 5711 can also be operated with an external power supply with 24 volts. You require this external power in the following situations: ● The CP 5711 is operated on an external hub without its own power supply. ● The USB interface on the PC is a low-power interface and therefore only supplies
100 mA. ● The end termination can be activated on the PROFIBUS connector if the CP 5711
is located at the end of the cable. If you want this termination to be active even when no USB cable is connected, an external power supply is necessary.
Installing and connecting up
CP 5711 A5E02399122-01, Release 02/2009 51
CAUTION
Disconnecting the device from the external power supply If you want to disconnect the device from the external power supply, follow these steps: 1. Shut down any communication via the CP 5711. 2. Disconnect the USB connection from the device to the PC. 3. Disconnect the external power supply from the device.
Parallel operation with other USB devices
NOTICE The use of other USB devices (for example a Webcam, mass memory, ...) on USB ports of the PC can affect the performance of the CP 5711.
NOTICE Removing and inserting USB devices can cause disrupted functions on the USB interface. In extreme cases, communication via the CP 5711 may even be aborted making it necessary to restart the application.
Note If you are operating two CP 5711 modules connected to one computer, use different root hubs.
Installing the software
CP 5711 A5E02399122-01, Release 02/2009 53
Installing the software
Installing the driver
Prerequisite
The following requirements must be met:
The USB controller is enabled in the BIOS of the computer.
Installing the CP 5711 driver
The driver is installed automatically when you install the "SIMATIC NET, PC Software" with CD 2008 + SP1.
The CP 5711 is supported by the CD "SIMATIC NET, PC Software, Edition 2008 + SP1".
The STEP 7 version released for the CP 5711 can be found in the readme file of STEP 7.
Uninstalling the driver
Uninstalling the CP 5711 driver
The driver is uninstalled automatically when you uninstall the "SIMATIC NET, PC Software" CD or STEP 7. If you have installed both software programs, and only uninstall one of them, the driver remains installed.
Note When uninstalling STEP 7, note the following instructions in German: http://support.automation.siemens.com/ww/view/de/189025 English: http://support.automation.siemens.com/ww/view/en/189025
Commissioning
CP 5711 A5E02399122-01, Release 02/2009 55
Commissioning
Configuring the CP 5711 Use NCM PC (included on the CD for SIMATIC NET) or STEP 7 to create an appropriate configuration for the CP 5711.
If the CP 5711 is not in the hardware catalog of STEP 7 or NCM PC, you can also use a CP 5512. The configuration of the CP 5711 is backwards compatible with the CP 5512.
Changing from CP 5512 to CP 5711 The CP 5711 can be operated with the configuration of a CP 5512.
Note The system always gives priority to the CP 5512. This means that you must remove an existing CP 5512 module and its configuration from the PC station before you change to the other module.
If a CP 5512 is present, follow the steps below:
1. Delete the configured module from the Station Configuration Editor if the CP 5512 is configured.
2. Remove the CP 5512 hardware from the PC.
3. Restart your PC.
4. Connect the CP 5711 to your PC and install the driver.
5. Configure the CP 5711.
6. Download the CP 5512 configuration.
Note If no CP 5512 exists physically, the system accepts the CP 5711 as a substitute. The system will, however, indicate that the target module is not a CP 5512.
Approvals and certificates
CP 5711 A5E02399122-01, Release 02/2009 57
Approvals and certificates Electromagnetic compatibility
The SIMATIC NET product meets the requirements of the EC Directive: 2004/108/EC "Electromagnetic Compatibility"
The communications processor is designed for use in the following areas: Requirements Area of application
Emission Immunity Residential area, business and commercial operations, and small businesses
EN 61000-6-3 EN 61000-6-1
Industrial area EN 61000-6-4 EN 61000-6-2
Installation guidelines
The communications processor meets the requirements if you adhere to the installation and safety instructions contained in this description and in the "PROFIBUS Network Manual".
Working on the product
To protect the communications process from electrostatic discharge, personnel must first discharge any electrostatic charge from their body.
Note The communications processor was tested with a device that also complies with the standards listed above. If the communications processor is operated with a device that does not meet these standards, there is no guarantee that the corresponding values will be adhered to.
Conformity certificates
You will find the EC Declaration of Conformity on the Internet at the following address:
http://supportauthoring.automation.siemens.com → section Self-help; enter "EC Declaration of Conformity" and the product name; Example German: "EG-Konformitätserklärung CP 5711", Example English: "Declaration of Conformity CP 5711".
Approvals and certificates
CP 5711 58 A5E02399122-01, Release 02/2009
Machinery directive
This communications processor is not a machine in the sense of the EC Machinery Directive. There is therefore no declaration of conformity relating to the EC Machinery Directive 2006/42/EEC for this communications processor.
If the communications processor is part of the equipment of a machine, it must be included in the procedure for obtaining the declaration of conformity by the manufacturer of the machine.
Notice for Australia (C-TICK)
The communications processor meets the requirements of the AS/NZS 3548 standard.
CSA approval
The communications processor has an approval in accordance with the CAN/CSA C22.2 No. 60950-1 standard.
ATEX, cULus and FM approval
The communications processor has the following approvals: ● EN 60079-15:2005
EN 60079-0:2006 II 3 G Ex nA II T.. KEMA 07 ATEX 0145
● c-UL-us: UL 60950-1 CSA C22.2 No. 60950-1
● FM 3611 Hazardous (Classified) Location Electrical Equipment: Non Incendive / Class I / Division 2 / Groups A,B,C,D / T* and Non Incendive / Class I / Zone 2 / Group IIC / T*
● c-UL-us for hazardous location*: ISA 12.12.01-2000, CSA C22.2 No. 213-M1987 CL. 1, Div. 2 GP. A.B.C.D T.. CL. 1, Zone 2, GP, IIC, T.. CL. 1, Zone 2, AEx nC IIC T..
(T.. / T* = For concrete information on the temperature class, refer to the name plate)
Approvals and certificates
CP 5711 A5E02399122-01, Release 02/2009 59
FCC approval
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help.
Siemens AG is not responsible for any radio television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Siemens AG. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.
Note The specified approvals apply only when the corresponding mark is printed on the communications processor.
Technical specifications
CP 5711 A5E02399122-01, Release 02/2009 61
Technical specifications The following technical specifications apply to the CP 5711 communications processor: Construction Dimensions (H x W x D) in mm 137 x 85 x 35 Weight approx. 255 g Module connector principle USB
Power Operating voltage Optional power supply unit
Imax = 300 mA V = 24 V
Current consumption Max. 500 mA (USB)
Data transfer Transmission rate 9.6 kbps to 12 Mbps
Interfaces Connection to PG/PC USB V2.0, compatible with V1.1 Plug in cable 9-pin D-sub female connector with screw
locking mechanism USB socket type B with locking mechanism
Type of transmission RS-485 floating within the SELV limits Mode of the PROFIBUS interface Floating (interface signals), non-floating
(cable shield)
Technical specifications
CP 5711 62 A5E02399122-01, Release 02/2009
Electromagnetic compatibility (EMC) Emission Class B to EN 55022
FCC class B Immunity on signal lines (PROFIBUS only)
+/- 2 kV to IEC 61000-4-5, surge +/- 1 kV to IEC 61000-4-4, burst
Immunity against electrostatic discharge +/- 6 kV, contact discharge to IEC 61000-4-2
Immunity against RF radiation ● 10 V/m at 80 MHz – 2 GHz to IEC 61000-4-3
● 10 V/m at 80 % amplitude modulation with 1 kHz
● 10 kHz – 80 MHz to IEC 61000-4-6
Safety UL/CSA approval The CP 5711 meets all requirements for
additional modules in compliance with the cULus approval.
Mechanical environmental conditions Vibration during operation Tested to EN 60068 2 6: 10 to 58 Hz,
Amplitude: 0.075 mm, 58 to 500 Hz; Acceleration: 10 m/s2, 10 cycles/axis
Shock during operation Tested to EN 60068 2 27: Half sine: 50 m/s2 (5 g), 30 ms, 100 shocks/axis
Climatic conditions Temperature (operation) Tested to IEC 60068 2 1, 60068-2-2:
0 °C to +60 °C, Change of temperature: max. 10 K/h
Transport/storage temperature -40 to +70 °C, Change of temperature: max. 20 K/h
Humidity (operation) Tested to EN/IEC 60068-2-78: 95 % / 16h at 30 °C (no condensation)
Technical specifications
CP 5711 A5E02399122-01, Release 02/2009 63
Climatic conditions Fast change of temperature during operation
Tested to IEC 60068-2-14: 0 °C / 3h; +60 °C / 3h, 5 cycles
Fast change of temperature during storage/transportation
Tested to IEC 60068-2-14: -40 to +70 °C, 2 cycles
Change of temperature with humidity during storage/transportation
Tested to EN/IEC 60068-2-30: 25 to 55 °C at 97 % (no condensation)
Pin assignment of the PROFIBUS interface
The D-sub female connector has the following pin assignment:
5 4 3 2 1
9 8 7 6
Figure 7.1 Pin assignment of the D-sub female connector
Technical specifications
CP 5711 64 A5E02399122-01, Release 02/2009
Pin no. Short name
Meaning Input/ output
1 NC Socket 1 is not connected. - 2 NC (M24) Socket 2 is not connected. With other
PROFIBUS components, the return line of the floating 24 V power supply may be over this pin.
-
3 LTG_B Signal line C of PROFIBUS Input/output 4 RTSAS RTSAS, input signal for direct MPI link.
The control signal is "1" active when the automation system connected over a special MPI cable is sending.
Input
5 M5EXT M5EXT return line (GND) of the 5 V power supply. The current load of an external consumer connected between P5EXT and M5EXT must not exceed a maximum of 20 mA.
Output
6 P5EXT P5EXT power supply (+5 V). The current load of an external consumer connected between P5EXT and M5EXT must not exceed a maximum of 20 mA to activate the termination (short-circuit proof).
Output
7 NC (P24V) Socket 7 is not connected. With other PROFIBUS components, the P24V supply of the floating 24 V power supply may be over this pin.
-
8 LTG_A Signal line A of PROFIBUS Input/output 9 RTS RTS output signal of the CP 5711
module. The control signal is "1" active when the CP 5711 is sending.
Output
Shield The shield is connected to the connector housing, PROFIBUS and USB shield are electrically connected.
Technical specifications
CP 5711 A5E02399122-01, Release 02/2009 65
CP 5711 dimension drawing
CP 5711 front view and view from above
s
CP 5711
PW
R U
SB
PW
R E
XT
AC
T
LNK
/SF
IDE
NT
85
137
35
All dimensions in millimeters
top related