aw-hs50 – dvi input & output...output ・ dvi output resolution can be selected from the list...

★ AW-HS50 switcher has one DVI-D input and one DVI-D output.

This is to explain supported resolutions and setting procedures for the input and output.

■ Input

* Input signal is automatically recognized according to its resolution. Listed in Figure 1 are the resolutions of images

that can be input.

<Note>

・ If an input signal has resolution other than the above, it cannot be taken in properly.

Then the output image may be a black screen or distorted.

・ HDCP is not supported. If a copyright-protected DVD player or PC is connected as a source, the output image is a

black screen or distorted.

・ Analog signals cannot be input.

* The angle of view of an input signal image can be changed as necessary. – (Figure 2)

DVI-D Output

Connector

(Figure 2: Input View Angle Settings)

(Figure 1: Supported Resolutions)

DVI-D Input Connector

AW-HS50 – DVI Input & Output

(AW-HS50 Rear Panel)

XGA 1024 X 768/60Hz

WXGA 1280 X 768/60Hz

SXGA 1280 X 1024/60Hz

WSXGA+ 1680 X 1050/60Hz

UXGA 1600 X 1200/60Hz

WUXGA 1920 X 1200/60Hz

1080/59.94p 1920 X 1080/59.94Hz

1080/50p 1920 X 1080/50Hz

① Hold down OSD ON button – (Fig.3-A) for 2 seconds to open the menu. (Hold it down again for 2 seconds to close

the menu.)

② Use OSD/TIME dial – (Fig.3-B) to change the menu setting below.

Menu: [10] Input Menu ＞ 5. DVI-IN ＞ 4. Scale ⇒ [Fit-V, Fit-H, FULL] – (Figure 4) * Default: [Fit-V]

■ Output

・ DVI output resolution can be selected from the list below – (Figure 5) by the menu setting.

① Hold down OSD ON button – (Fig.3-A) for 2 seconds to open the menu. (Hold it down again for 2 seconds to close

the menu.)

② Use OSD/TIME dial – (Fig.3-B) to change the menu setting below.

Menu: [11] Output Menu ＞ 5. DVI-OUT: Size ⇒ [(Fig.5: Supported Resolutions)] – (Fig.6-A) * Default: [Auto]

<Note>

・ When the resolution setting is [Auto], DVI signal is used to gather information about the device to which it is output

so that the image is output at the most suitable resolution.

・ If the image is not displayed correctly in spite of [Auto] setting, please change over to a setting other than [Auto].

・ Analog signals cannot be output.

* The angle of view of an output signal image can be changed as necessary. – (Figure 7)

Menu: [11] Output Menu ＞ 6. DVI-OUT: Scale ⇒ [Fit-V, Fit-H, FULL] – (Fig.6-B) * Default: [Fit-V]

(Figure 5: Supported Resolutions)

(Figure 3: AW-HS50 Control Panel)

(Figure 4: AW-HS50 Menu Display Screen) （A）

（B）

■ Assigning the output signal

DVI output signal can be assigned to any of [PGM, PVW, CLN, AUX, MV, KEY OUT].

Menu: [11] Output Menu ＞ 3. DVI-OUT ⇒ [PGM, PVW, CLN, AUX, MV, KEY OUT] – (Fig.8) * Default: [AUX]

(Figure 7: Output View Angle Settings) (Figure 6: AW-HS50 Menu Display Screen)

（A） （B）

(Figure 8: AW-HS50 Menu Display Screen) (Figure 9: Output Signal)