cleaners brochure - martin eng · p/n sc35 bpl/poly replacement blade sc35 bpl/blad. part no....
Post on 16-Oct-2020
1 Views
Preview:
TRANSCRIPT
Bauxite, coke,
refuse,
steel/ore, etc.
Limestone
coal
Clinker
A B
A
B
A
A
SC16
Pin Satch
SQC2S TM X
X
X
X
X
X
X
X
X
SC10 XXX
MARTIN
Has a unique installation and removal guide/cradle for easy
removal and replacement of blade carrier tube, especially
when servicing cleaners on wide belts. Patented rubber
blade mountings (i) Maintain constant belt pressure -
irrespective of belt profile or irregularities. (ii) Allow blades
to deflect when encountering metal belt fasteners and
accommodate reversing belts. Four types of blade are
available to suite various applications.
R SC16 SECONDARY
BELT CLEANER
MARTIN
MARTIN has re-designed the SC16 Cleaner Assembly with
buffer and blade assembly are on a removable cartridge,
for quick changes of buffers and blades. (No need to remove
mainframe/carrier tube). Lower the cleaner assembly away
from the belt, remove the hitch pin and remove the cartridge.
Place new cartridge in position, replace pin and re-tension the
scraper. Blade mounts do not have to be disassembled for
servicing on site. Old cartridge can be returned to workshop
for refurbishment.
R SQC2 SECONDARY
BELT CLEANER
MARTIN
On belts demonstrating “above average” carryback after the
discharge point, a double SC16 can be installed. This is usually
hung from a Channel T-bracket. Other brackets offer different
options depending on space available.
R SC16 DOUBLE SECONDARY
BELT CLEANER
MARTIN
The SC10 is just 2/3 the size of the SC16 and the advantages
over the SC16 is that it can be used for a secondary application
where installation space is limited. It also offers an affordable
option for smaller mines but only up to 1200mm belt widths.
R SC10 SECONDARY
BELT CLEANER
Tech Data Sheet N/A
Assembly P/N PLSECSCR00300
Channel“T” bracket 450mm
“T” bracket 350/450mm
350/450mmStandard Bracket
CLMP76 CLMP60 CLMP43
76.5mm diam.Pipe clamp
60.5mm diam.Pipe clamp
Adjustingbracket
SC16 SND
SC16/ARBSND
SC16Rubber buffer
Type SC16/ARB Tungstenfor acidic applications
Type SC16/HAR Tungstenfor all normalapplications
Special impact-resistant Tungsten with protector plate for belts with metal fasteners
SC16 SND
SC16/ARBSND
SC16Rubber buffer
Type SC16/ARB Tungstenfor acidic applications
Type SC16/HAR Tungstenfor all normalapplications
/ ROTARY BRUSH
MARTIN
The scraper is mounted to the conveyor stringers ahead of
the tail pulley or other nip location. In cases of severe
contamination and/or an inclined belt situation, the center
point mounting is spring loaded to provide a constant
positive pressure on the plough, thus ensuring continuous
belt contact and optimum cleaning.
R V-PLOUGH
BELT CLEANER
P/N SS32 VPL/Poly Replacement Blade SS32 VPL/PBLD
MARTIN
The Angle or Bias plough is a variation of the “V-plough
concept, for use in situations where material can only be
discharged at one side of the belt. The plough is mounted
on the conveyor stringers and the blade is held at a constant
angle to the belt surface, in a trailing position by parallel
linkages attached to the blade mountings at each side.
The scraper can be installed to discharge to either side of
the belt.
R BIAS PLOUGH
BELT CLEANER
P/N SC35 BPL/Poly Replacement Blade SC35 BPL/BLAD
Part No. L3651-06/11
top related