connectivity brackets for cable cubby 1200 and 1400 ... · connectivity brackets for cable cubby...
Post on 25-Feb-2021
4 Views
Preview:
TRANSCRIPT
Connectivity Brackets for Cable Cubby 1200 and 1400 • Setup Guide
This guide provides instructions for assembling and installing the following accessories for the Cable Cubby 1200 and 1400:
• Cable pass-through bracket — small
• Retractor filler bracket — small
Connectivity brackets allow users to configure the Cable Cubby enclosure with the power module installed at the center and two cable pass-through modules on the sides (see the image at the bottom of this page) or two retractor assemblies on the sides (see the next page).
Cable Pass-Through Bracket
Step 1 — Assemble the cable pass-through brackets
Step 2 — Install cable pass-through brackets in the Cable Cubby
Follow the steps below to install the brackets on the left and right sides of the power module.
NOTE: For instructions on installing the power module, see the Cable Cubby 1200 and 1400 Installation Guide.
Secure the brackets using the provided mounting screwwith star washer (4).
Insert the brackets into the Cable Cubby.
1
2
Insert cables through the bottom of the connectivity bracket and into the holes of the grommet plate.
Secure the grommet plate on the connectivity bracket, using four of the provided module screws.
Use the provided mounting screw with the star washer to secure the bracket in place.
Insert the mounting pin through the retractors.
Insert the retractor filler bracket into the Cable Cubby enclosure as shown above.
Use the clip to secure the mounting pin.
1
2 1
2
3
4
Snap the included hole plugs into any unused holes.
Insert cables through the bottom of the bracket and into the holes of the grommet plate.
Secure the grommet plate on the bracket, using four of the provided module screws.
12
3
3
Use the clip to securehe mounting pin.
2
125V~ 12A MAX TOTAL
Insert the brackets into the Cable Cubby.
1
2 Use the provided mounting screws with the star washers to secure the brackets in place.
Connectivity Brackets • Setup Guide (Continued)
Secure the brackets using the provided mounting screwwith star washer (4).
Insert the brackets into the Cable Cubby.
1
2
Insert cables through the bottom of the connectivity bracket and into the holes of the grommet plate.
Secure the grommet plate on the connectivity bracket, using four of the provided module screws.
Use the provided mounting screw with the star washer to secure the bracket in place.
Insert the mounting pin through the retractors.
Insert the retractor filler bracket into the Cable Cubby enclosure as shown above.
Use the clip to secure the mounting pin.
1
2 1
2
3
4
Snap the included hole plugs into any unused holes.
Insert cables through the bottom of the bracket and into the holes of the grommet plate.
Secure the grommet plate on the bracket, using four of the provided module screws.
12
3
3
Use the clip to securehe mounting pin.
2
125V~ 12A MAX TOTAL
Power module
Retractor �ller bracket
Retractor assembly
68-2474-01Rev. A09 13
Extron USA Headquarters+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Retractor Filler BracketThe retractor filler bracket fills the empty space between a two-retractor assembly (see image below) and the center mounted power module. Follow the steps below to install a two-retractor assembly and the retractor filler bracket.
NOTE: For instructions on installing the power module, see the Cable Cubby 1200 and 1400 Installation Guide.
Application with Rectractor Assemblies
NOTE: For instructions on mounting the retractors in the horizontal orientation, see the Cable Retractor Setup Guide available online at www.extron.com.
top related