continuous production model (first draft)
Post on 29-Nov-2014
816 Views
Preview:
DESCRIPTION
TRANSCRIPT
PRECISION AUTO BODY Continuous Production Model
The hours of operation are as follows:
Monday thru Friday8am – 5pm
COUNTINUOUS PRODUCTION MODEL:a designed process of interconnecting events that allow production to flow freely with predictable consistent results.
Everyone must have a clear understanding of our process so the consistent desired predictable result can be achieved.
Model Overview# 1 :The production model is broken into four color coded
process zones. Everyone must understand that each process zone within our shop shall have goals and tasks that will require completion before the vehicle can move to the next process zone.
# 2 :Each step in our process reduces the size of the vehicle to
enter the fast track process zone. The repair no matter what the original size of the repair was. Building the vehicle up in the red process zone, with 2 to 3 hours of hands-on repair work, qualifies
# 3 :Visual management controls in place will aid the
production process so that it can be understood at a glance.
# 4:throughout the process there will be four repair
verifications within our process, the repair check point will help aid in quality audit and pace the pulling of work from each process department zone.
THE FOUR COLOR PROCESS ZONERed Orang
eGreen Purpl
e
How the Red Process Zone is DesignedTo make this more visible, the areas within the
Red Process Zone should be color coded.
Red Stripes on the floor.
Red color overhead signs with the name of the area.
This will make it easier to see and understand what zone the vehicle is in, plus what needs to be completed on the vehicle before it can move to the next colored zone.
Red Process Zone
How the Red Zone Process WorksThe Red Process Zone works much like a
modified traditional body shop.Work in this zone can be anything from body
work that will take longer than 3 hours to repair, suspension repair, body panel replacement, frame pulling to structural repair or replacement.
Within the Red Process Zone you may work on vehicles that have not received all the parts.
Red Process Zone
Strategic Disassembly/Repair PlanningBased on what needs to be done to the vehicle and the size of the
repair and how much time it will take to complete the repair to a certain point.
In Repair Plan Disassembly it will be determined if the vehicle meets the criteria to be placed directly in the Orange Process Zone for repair.
Repair Plan Disassembly is very much tied to the Pulling Department. If you have a vehicle that requires pulling and measuring the
estimate should not be locked until pulls are made.These pulls should be done the same day where possible.Once the pulls are made, times for conjunctive repairs can now be
determined.Damaged welded panels that need to be replaced are removed where
possible.Mechanical and Suspension damage identified and diagnosed.
Red Process Zone
REPAIR PLAN AUDIT IS CONDUCTED THROUGH THE VISUAL MAPPING
PROCESS AND ALL ON VEHICLE NOTES ARE APPLIED
Reducing the possibility that anything downstream from that point could stop the vehicle from going forward.
Repair plan is finalized and all parts ordered.Vehicle is then placed in the Parts Waiting
area.
Red Process Zone
Structural Repair and Building Area If no parts are needed to complete the next part of the repair, the
vehicle may move to the next Red Process Zone building repair area.
Under no circumstances should the vehicle be allowed to move to the Orange Process Zone area without 100% of all the parts received and verified to be the correct parts.
If parts are needed…once the parts arrive and are verified correct, the vehicle is moved to the Structural Repair Area in the Red Process Zone. All structural repairs are completed at this time All welded on panels are install i.e. Core supports, Aprons, Rail, Quarter Panels Vehicle is re-measured on the floor to verify correctness and printout
placed in file and vehicle Vehicle is move to Red Process Zone Paint Cut-In
Red Process Zone
Paint Cut-InAll paint cut-in of the vehicle is complete in
this process…Door openingsCore supportAprons and railTrunk openings
Once all cut-in has been completed the vehicle can be moved to the build area.
Red Process Zone
BuildAll pre-build takes place at this time, insuring proper
fit of parts.All Mechanical build
Radiators and A/C condensersVehicles that come from the Red Process Zone have
had all the variables taken out of the repair.The randomness of different size repairs has been
reduced to a very predictable size.Special needs have been addressed i.e. air bags,
codes cleared, suspension and wheel alignments, all mechanical.
The Red Process Zone allows vehicles to move through the balance of the repair process at a very predictable pace.
Red Process Zone
Goal and Repair Verification AuditPrior to “Ready For Production” repair verification
hand off, the vehicles requires only 2 to 3 hours of hands on repair or parts replacement or less to be complete.
Proper operation, fit and gaps of all repaired or replaced areas.
All suspension replacement and Wheel Alignment completed.
All Mechanical and electrical repairs completed.All structural repairs completed.All paint cut-in completedAir Bag replacement and codes cleared.All repair verification audit met.
Red Process Zone
TELL ME THE RULES AND I WILL SHOW YOU HOW TO WIN THE
GAME
Red Process Zone
Rules Damage Analysis of all vehicles Complete disassembly of all damaged areas Paint color variant obtained and Color mixed Color spray out All Structural Pulling and Measuring Repair Plan Finalized All Parts ordered and received All Structural Repair All Pre-fit of bolt on parts All welded-on parts replaced and measurements verified Proper operation, fit and gaps of all repaired or replaced areas All vehicle paint cut-in All damaged parts identified and replaced Wheel Alignment completed All mechanical and electrical repairs including engine R&I Cooling and AC systems recharged and checked Damaged Air Bag and Sensors replaced and codes cleared Interior Build if needed All Quality Standards met
Red Process Zone
How the Orange Process Zone is DesignedHow the Orange Process Zone is Designed
To make this more visible, the areas within the Orange Process Zone should be color coded.Orange Stripes on the floor. Orange color overhead signs with the name
of the area.
This will make it easier to see and understand what zone the vehicle is in, plus what needs to be completed on the vehicle before it can move to the next colored zone.
Orange Process Zone
How the Orange Process Zone WorksThe Orange Process Zone starts outside in the
parking lot, in the area we know as “Ready for Production”.
In order for a vehicle to be in this area, three things must be true
1. It will take less than two or three hours of work to prepare the vehicle for Paint and Reassembly.
2. 100% of ALL the parts needed have been received and verified.
3. ALL the Goals of the Red Process Zone have been met.
Orange Process Zone
GoalsDeliver to the Green Process Zone ONE vehicle
every 60 to 90 minutes or less.Deliver to the Green Process Zone (Paint)
vehicles that meet all Quality standards, free of defects i.e. sandpaper scratches and pinholes.
Deliver to the Green Process Zone vehicles requiring only 60 to 90 minutes or less of hands on parts installation in the reassembly area.
Verify that any issue that could stop the vehicle from going forward has been addressed and completed.
Orange Process Zone
Goal and Repair Verification Audit
Body repairParts replacementPanel alignment and proper operationMeet all Quality Standards, free of defects i.e.
sandpaper scratches and pinholes.Anything that is required to reduce the size of
the vehicles to require only 60 to 90 minutes or less of hands on parts installation in the Reassembly area.
Verify that no issue could stop the vehicle in Reassembly.
Orange Process Zone
RulesNo vehicles in this zone without ALL 100% of
their parts received and verified.No repairs that will take longer than 3 hours to
complete.All quality check points prior to entering the
production flow line have been completed, passed and signed off.
Only pass to paint quality repairs that won’t need rework.
Only pass to reassembly vehicles that can be reassembled in less than 90 minutes.
Orange Process Zone
To make this more visible, the areas within the Green Process Zone should be color coded.
Green Stripes on the floor.Green color overhead signs with the name of
the area.This will make it easier to see and understand
what zone the vehicle is in, plus what needs to be completed on the vehicle before it can move to the next colored zone.
How the Green Process Zone is Designed
Green Process Zone
How the Green Process Zone WorksThe Green Process Zone starts in the Paint
Buffer.In order for a vehicle to be in this area, three
things must be true1. Items remaining for Reassembly to install on
the vehicle will take less than 90 minutes to install.
2. 100% of ALL repairs have been completed and quality has been verified.
3. ALL the Goals of the Orange Process Zone have been met.
Green Process Zone
GoalsPaint DepartmentPaint to deliver to the Green Process Zone
(Reassembly) ONE vehicle every 60 to 90 minutes or less.
Deliver to the Green Process Zone (Reassembly) vehicles that meet all Quality Standards, free of defects i.e. color match.
Free of needing any correction of any kind.
Green Process Zone
Re-Assembly DepartmentReassembly to deliver to the Green Process Zone
(Detail) ONE vehicle every 60 to 90 minutes or less that has achieved all Quality Standard.
All customer needs and concerns addressed and corrected.
A vehicle that has passed all quality check points.Detail to deliver to the Purple Process Zone ONE
vehicle every 60 to 90 minutes that has been properly cleaned and has passed the Fit and Finish Inspection.
Goals
Green Process Zone
GoalsDetail DepartmentAll customer needs and concerns addressed
and corrected.A vehicle that has passed all Quality Check
Points including the CSR Fit & Finish check.Detail to deliver to the Purple Process Zone
ONE vehicle every 60 to 90 minutes that has been properly cleaned.
Green Process Zone
Goal and Repair Verification AuditAll paint prep workAll paint workMeet all Quality Standards, free of defects i.e. color match,
correction of any kind.Paint to produce ONE vehicle every 60 to 90 minutes.Reassembly to install all parts remaining on parts cat i.e. bumper,
headlamp, grille, moldings, door handle, weather strips, etc.Quality met and Quality inspection completed.Reassembly to deliver to the Green Zone (detail) ONE vehicle
every 60 to 90 minutes.Vehicles cleaned inside and out, including under hood if we
worked on the front or inside trunk if we worked on the rear of the vehicle.
Fit and Finish Inspection complete.
Green Process Zone
RulesNever place a
vehicle in the Purple Process Zone that has something that has not been completed.
All Quality Standards met and verified.
Green Process Zone
How the Purple Process Zone is DesignedHow the Purple Process Zone is Designed
To make this more visible, the areas within the Purple Process Zone should be color coded.
Purple Stripes on the floor.Purple color overhead signs with the name of
the area.This will make it easier to see and
understand what zone the vehicle is in, plus what needs to be completed on the vehicle before it can move to the next colored zone.
Purple Process Zone
How the Purple Process Zone WorksIn order for a vehicle to be in this area, three
things must be true.There are NO items remaining to be
completed on the vehicle.Quality has been achieved and verified;
customer concerns have been addressed and verified.
The collective Goals of all the process zones have been met.
Purple Process Zone
Goals Is to provide the best possible customer experience and service that far
exceeds the customer’s expectations. A controlled area to deliver to the customer their properly staged vehicle. No Surprises! Delivering from the Purple Process Zone enables the CSR to schedule the
time of vehicle pick up with the customer so we can provide a focused attention to the customer that makes them feel valued.
The customer is never notified that the vehicle is ready for pick up until the CSR or person that will be delivering the vehicle back to the customer, has been able to review the vehicle and complete the Final Inspection Checklist.
This gives the CSR the opportunity to complete the a final fit and finish review of the vehicle without having the pressure of the customer picking the vehicle up in 10 minutes.
This helps prepare the CSR to resell the vehicle to the customer during delivery.
Allows us to take pride and have confidence in knowing that we have done everything with quality.
Purple Process Zone
Goal and Repair Verification AuditCSR’s to complete a final review of the file and
repairs made to the vehicle.Complete a Fit and Finish inspection of the
vehicle.Verify that we have done everything with quality.Double check that ALL the customers concerns
have been addressed and corrected.Once all these tasks and Goals have been
achieved the vehicle is considered “Complete”.Contact the customer and schedule the vehicle
delivery.Purple Process Zone
RulesThere are NO items remaining to be completed
on the vehicle.Quality has been achieved and verified, customer
concerns have been addressed and verified.The customer Must Not be notified that the
vehicle is ready for pick up until, the CSR or person that will be delivering the vehicle back to the customer, has been able to review the vehicle and completed the Final Inspection Checklist and everything is ready for the customer.
Purple Process Zone
Contact InformationRANDY S FERRESE SR.824 BLUE BIRD CIRCLE
MAYS LANDING, NJ 08330609 553 4244
FERRESEWV77@HOTMAIL.COM
top related