cv eng ahmed
Post on 07-Aug-2015
74 Views
Preview:
TRANSCRIPT
PERSONAL INFORMATION
Name: Ahmed Hamdy ElMahdyMarital status: FinishedMobile: 00201006900796Email: Eng_ahmed_152@yahoo.comAddress 1: Giza- EgyptADDRESS 2: Aluminium city–Naga Hammady-Qena - Egypt
EDUCATION
B.Sc. Metallurgical Engineering Science, Mining, petroleum, and Metallurgy Department - Faculty of Engineering - Cairo University - Egypt.
Graduation year: May 2011 General Grade: Good (66%) Graduation project: Extracting of Aluminum in aluminum cells Graduation project grade:very good
Related Courses:
Casting
Iron and steel industry
Metal forming [hot rolling,cold rolling and extrusion]
Structure and design of alloys
Physical metallurgy and Corrosion
Welding[consumable and non-consumable]arc welding
Destructive and non-destructive testing(penetration test, magnetic test, ultrasonic test and radio graphic test)
Extraction of non-ferrous metals [aluminum, tin and copper]
Jobobjectives
Seeking a challenging and creative job where I can make the best use of my interpersonal, communication and analysing skills. Preferring one of the following positions:
Mining Engineer
Inspection Engineer
Production Engineer
Maintenance Engineer
Mineral processing Engineer
Safety Engineer
Courses
NDT inspection for non-destructive testing and welding technology in EWA (Egyptian welding academy)
1. Applied welding technology
2. Liquid penetration test
3. Magnetic penetration test
4. Ultrasonic test
5. Radio graphic test
6. Visual inspection
With certificate
Work experiences
Egypt alum company for extraction of aluminium
Quality engineering group ( inspection,NDT service)
Training experience
The Aluminum Company of Egypt in Naga Hammady (Egypt alum).
18/8/2007 to 30/8/2007
1/7/2008 to 16/7/2008
1/8/2009 to 13/8/2009
13/1/2010 to 28/1/2010
Egyptian company of Egypt for steel (Al Ezzdekhela steel co.)
12/7/2009 to 23/7/2009
Familiar with the following QA/QC Scope: Documentation: - Preparing WPSs (Welding Procedure Specifications), PQRs (Procedure Qualification Records) and WPQs (Welder Performance Qualifications) & Check Specifications (Year and Revision) - Preparing Weld Map & ITP (Inspection & Test Plan) and Review Fabrication Drawings - Material Verifications as per Procurement Order (P.O.) and Reviewing of Mill Test Certificate (MTC) and MTRs/Lab Reports for traceability and conformance to mechanical /chemical properties in accordance with applicable Codes, Standards & Client Spec. Requirements - Validate Calibration Certificates of Welding Equipment & Inspection Instruments
Incoming Material Inspection: Dimensional & Visual Inspection and Lamination Test (if required) Welder Qualification: Witness Welder Qualification tests in association with approved WPS Inspection before Welding: - Check welding equipment and all related ancillaries (cables, regulators, ovens) - Check welding consumables for size, condition, specification and storage - Check layout/marking for cutting of materials - Check fit-up & preparation of the joints (relevant bevel angles, root face, root gap, etc.) as per the detailed drawing and WPS - Dimensional inspection & monitor all tack welding - Check method of preheat (if applicable) & pre-welding distortion control
Inspection during Welding: - Check amperage, voltage, polarity & travel Speed - Check welding technique & weld direction - Ensure qualified welders are performing welding efficiently and in the specified welding time - Ensure adequate inter pass cleaning & inter pass temperature
Inspection after Welding: - Check weld dimensions, contour & width - Carry out visual welding inspections & Ensure post weld cleaning (arc strikes, spatters) - Check PWHT (if applicable) and Review PWHT Charts & Specifications - Witness & Evaluation of Non Destructive Examinations and Destructive tests of weld samples - Mark up repair areas and Monitor & Control the welding repair - Checking of Sand Blasting & Inspection on Painting to meet required microns
Final Documentation: Review & Maintain Dimensional, NDT, Sand Blasting & Painting and Release to Site Reports Familiar with the following Codes & Standards: - ASME II Part A&C&D, ASME V, ASME IX, ASME B31.1, ASME B31.3 - AWS D1.1, AWS D1.5, AWS A2.4, AWS A3.0, EN-ISO 898-1, EN-ISO 898-2 - API 1104, API 5L, API 510, API 570, API 653
Computer Skills
Microsoft: MS DOS and Windows. Microsoft Office: Word, Excel. Internet.
ICDL UNESCOcertificate from South Valley University.
Languages
Arabic: native. English:Very good speaking and writing French:Fair knowledge.
InterpersonalSkills
Ability to learn and retain new knowledge quickly Working effectively with teamwork Highly adaptable, positive, resilient, patient risk-taker Willingness to work outside country of residence
top related