emerson ewl20s5 lcd tv service manual
Post on 23-Oct-2015
201 Views
Preview:
TRANSCRIPT
SERVICE MANUALThis service manual is for the EWL20S5 different LCD Module Assembly model, which is different from the previous EWL20S5 model. For EWL20S5 different LCD Module Assembly model, an “A” or the letter (L3222UC) is printed on rating label on the back of the unit. Refer to the rating label illustration at right.
Rating Label
"L3222UC" Suffix "A"
20″ COLOR LCD TELEVISION
EWL20S5
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1How to initialize the LCD Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.
1-1 L0306SP
SPECIFICATIONS
< TUNER >ANT. Input ---------------------- 75 ohm Unbal., F typeReference Level--------------- 20 Vp-p (LCD Green Cathode)Test Input Signal -------------- 400 Hz 30% modulation
< LCD PANEL >
< VIDEO >
< AUDIO >All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Note: Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications.
Description Condition Unit Nominal Limit
1. Intermediate Freq. PictureSound
MHzMHz
45.7541.25
------
2. Color Killer Sens.CH-2CH-10CH-55
dBµVdBµVdBµV
151515
202020
3. AFT Pull In Range (10 mV input) --- MHz ±2.1 ±0.7
Description Condition Unit Nominal Limit
1. Number of Pixels HorizontalVertical
pixelspixels
640 × 3480
------
2. Brightness cd/m2 500 ---
3. Response Time --- msec 16 ---
4. Support Color --- - 26 mil. (6 bit) ---
5. Viewing Angle HorizontalVertical
°°
-80 to 80-65 to 70
------
Description Condition Unit Nominal Limit
1. Over Scan HorizontalVertical
%%
77
------
2. Color Temperature---xy
°K92000.2860.294
---±0.3±0.3
3. Resolution HorizontalVertical
lineline
400350
------
Description Condition Unit Nominal Limit
1. Audio Output Power 10% THD: Lch/Rch W 1.0/1.0 0.8/0.8
2. Audio Distortion 500mW: Lch/Rch % 1.0/1.0 4.0/4.0
3. Audio Freq. Response -3dB: Lch-3dB: Rch
HzHz
50 to 12 k50 to 12 k
------
2-1 LTVN_ISP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV Circuit1. Before returning an instrument to the
customer, always make a safety check of the entire instrument, including, but not limited to, the following items:
a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.
b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.
c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.
d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.
ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.
ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED
TEST ALL EXPOSEDMETAL SURFACES
READING SHOULD NOT BE ABOVE 0.5 mA
EARTHGROUND
_
DEVICELEAKAGECURRENT
TESTER
+BEINGTESTED
2-2 LTVN_ISP
3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.
4. Hot Chassis Warning -
a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.
c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.
5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc.. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
2-3 LTVN_ISP
Precautions during ServicingA. Parts identified by the # symbol are critical for
safety.Replace only with part number specified.
B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp edged or pointed parts.
H. When a power cord has been replaced, check that 5~6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. Crimp type wire connectorThe power transformer uses crimp type connectors which connect the power cord and the primary side of the transformer. When replacing the transformer, follow these steps carefully and precisely to prevent shock hazards.Replacement procedure
1) Remove the old connector by cutting the wires at a point close to the connector.Important: Do not re-use a connector (discard it).
2) Strip about 15 mm of the insulation from the ends of the wires. If the wires are stranded, twist the strands to avoid frayed conductors.
3) Align the lengths of the wires to be connected. Insert the wires fully into the connector.
4) Use the crimping tool to crimp the metal sleeve at the center position. Be sure to crimp fully to the complete closure of the tool.
L. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet.
M. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.
2-4 LTVN_ISP
Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Region Clearance Distance (d), (d’)
110 to 130 V U.S.A. or Canada
≥ 3.2 mm (0.126 inches)
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
110 to 130 V U.S.A. or Canada
0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible
parts
Chassis or Secondary Conductor
Primary Circuit
Fig. 1
d' d
AC Voltmeter (High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
Fig. 2
3-1 TVN_SN
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Pb (Lead) Free SolderPb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
Pb free mark
Fig. S-1-1
3-2 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
Masking Tape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
3-3 TVN_SN
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.
2. The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
3-4 TVN_SN
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
<Incorrect>
CBA
Grounding Band
Conductive Sheet orCopper Plate
1MΩ
1MΩ
<Correct>
CBA
4-1 L3222DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.
2. Disassembly Method
Note:
(1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the Table."Step/
Loc. No.
Part
Removal
Fig. No.
Remove/*Unhook/Unlock/Release/Unplug/Unclamp/
Desolder
Note
[1] Rear Cabinet D1 11(S-1), 2(S-2), ---
[2] Jack Holder D2 3(S-3), (S-4) ---
[3] InverterCBA
D2D3
5(S-5), *CN450, *CN460, *CN490, *CLN411
---
[4] Main CBA D2D3
9(S-6), *CN101A, *CN102A, *CN103A, *CN801, *CN802
---
[5]
LCD Main CBA & Liquid Crystal Panel Unit
D2D3
13(S-7), *CN104, CN105 ---
[6] Function CBA
D2D3 3(S-8) ---
[7] IR Sensor CBA
D2D3 2(S-9) ---
[3] Inverter CBA
[5] LCD Main CBA & Liquid Crystal Panel Unit[4] Main CBA
[1] Rear Cabinet
[8] Speaker (s)
[2] Jack Holder
[7] IR Sensor CBA
[9] Front Cabinet
[6] Function CBA
[8] Speaker (s) D2D3 4(S-10) ---
[9] Front Cabinet D2 --------------- ---
↓(1)
↓(2)
↓(3)
↓(4)
↓(5)
Step/Loc. No.
Part
Removal
Fig. No.
Remove/*Unhook/Unlock/Release/Unplug/Unclamp/
Desolder
Note
4-2 L3222DC
Fig. D1
[1] Rear Cabinet
S-2
S-2
S-1
S-1
S-1 S-1
S-1
S-1
S-1
S-1
Fig. D2
S-10
S-10
S-9
S-8
S-8
S-10
S-7
S-7
S-7
S-3
S-3
S-6
S-6
S-6S-5
S-5
S-4
S-7S-7
S-3 S-6
S-6
[5] LCD Main CBA & Liquid Crystal Panel Unit[7] IR Sensor CBA
[4] Main CBA
[3] Inverter CBA
[2] Jack Holder
[6] Function CBA
[8] Speaker
[8] Speaker
[9] Front Cabinet
4-3 L3222DC
TV Cable Wiring Diagram
CN101ACN102A
CN802CN801
Function CBA
IR Sensor CBA
Inve
rter
CB
A
Main CBA
LCD Main CBA Unit
To SpeakerTo Speaker
CN103A
CN312CN311
CN
460CN101B
CN102BCN103B
CLN
411
CN
411
CN
490
CN
450
CN105
To Liquid Crystal Panel
To Liquid Crystal Panel
Fig. D3
CN104
CLN104
CLN105
CN111
CN113
CN112
5-1 L3222EA
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after
replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required1. DC Voltmeter
2. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)
3. Remote control unit: Part No. N0105UD or N0127UD
4. Color Analyzer
How to make Service remote control unit:1. Prepare normal remote control unit.
(Part No. N0105UD or N0127UD) Remove 3 Screws from the back lid. (Fig. 1-1)
2. Added J1 (Jumper Wire) to the remote control CBA. (Fig. 1-2)
How to set up the service mode:
Service mode:1. Use the service remote control unit.
2. Turn the power on. (Use main power on the TV unit.)
3. Press [SLEEP] button on the service remote control unit. Version of micro computer will be displayed on the LCD or display. (Ex: 0004FP-0.47)
1. Initial SettingGeneral: Enter the Service mode. (See page 5-1.)
Set the each initial data as shown on table 1 below.
Table 1: Initial Data
Fig. 1-1
Screws
Remote control unit (bottom)
Fig. 1-2
J 1
Remote Control CBA
ItemButton
(on the service remote control)
Data Value
BRT
[MENU] → [1]
120
CNT 140
CLR-R 64
CLR-B 64
TNT 128
V-TNT 128
SHR 35
S-BRT
[MENU] → [2]
120
S-CNT 140
S-CLR-R 64
S-CLR-B 64
S-TNT 128
S-SHR 35
C-BRT
[MENU] → [3]
124
C-CNT 144
C-CLR-R 69
C-CLR-B 69
C-TNT 128
C-SHR 35
5-2 L3222EA
2. Flicker Adjustment1. Enter the Service mode. (See page 5-1.)
2. Press [2] button on the remote control unit. The following screen appears.
3. If Flicker Adjustment is not fit, the screen become the following.
4. Press [CH o / p] buttons on the remote control unit so that flash stops.
D2-BRT
[MENU] → [5]
135
D2-CNT 145
D2-CLR-R 68
D2-CLR-B 68
D2-TNT 128
D2-SHR 35
D3-BRT
[MENU] → [6]
120
D3-CNT 144
D3-CLR-R 69
D3-CLR-B 69
D3-TNT 128
D3-SHR 28
COR(C/D1)[VOL p] → [1]
140
C-COR(C/D2) 140
COB(C/D1)[VOL p] → [3]
137
C-COB(C/D2) 137
DR(C/D1)[VOL p] → [4]
176
C-DR(C/D2) 176
DB(C/D1)[VOL p] → [6]
147
C-DB(C/D2) 147
ItemButton
(on the service remote control)
Data Value
VCOM110
VCOM110
FLASH (Go and Off)
5-3 L3222EA
The following adjustment normally are not attempted in the field. Only when replacing the LCD Panel then adjust as a preparation.
3. White Balance AdjustmentPurpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
Note: Use service remote control unit
1. Operate the unit for more than 20 minutes.
2. Input the White Purity (APL 80% or APL 13%).
3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. [RF/VIDEO1]Enter the Service mode. Press “VOL p” button on the remote control unit and select “C/D/S-1” mode. [VIDEO2]Enter the Service mode. Press “VOL p” button on the remote control unit and select “C/D/S-2” mode.
5. [RF/VIDEO1]When “x” value and “y” value are not within specification, adjust “DB (C/D1)” or “DR (C/D1)”. Refer to “1. Initial Setting.”Note: “DB(C/D1)” or “DR(C/D1)” must be adjusted within ±0.01.[VIDEO2]When “x” value and “y” value are not within specification, adjust “DB(C/D2)” or “DR(C/D2)”. Refer to “1. Initial Setting.”Note: “DB(C/D2)” or “DR(C/D2)” must be adjusted within ±0.01.
6. Turn the power off and on again. (Main power button on the TV unit.)
Test Point Adj. Point Mode Input
ScreenVOL. p buttons
[RF/VIDEO1] C/D1[VIDEO2] C/D2
White Purity (APL 80%)
or(APL 13%)
M. EQ. Spec.
Pattern Generator, Color analyzer
x: 0.256 to 0.316,y: 0.264 to 0.324
Figure
Color Analyzer
It carries out in a darkroom.
L = 3 cm
Perpendicularity
INPUT: WHITE 80%
6-1 L0306INT
HOW TO INITIALIZE THE LCD TELEVISION
How to initialize the LCD television:1. Turn the power on. (Use main power on the TV
unit.)
2. To enter the service mode, press [POWER], [2], [7], [1], and [MUTE] buttons on the remote control unit in that order within 5 seconds.
- To cancel the service mode, press [POWER] button on the remote control.
3. To initialize the LCD television, press “DISPLAY” button on the remote control unit.
4. Confirm "FF" indication on the upper right of the screen.
7-1
BLOCK DIAGRAMSSystem Control Block Diagram
L3222BLS
FU
NC
TIO
N C
BA
IC33
3(T
V M
ICR
O C
ON
TR
OLL
ER
)
3 21
KE
Y-IN
-12
2
CN
104
CLN
104
KE
Y S
WIT
CH
11K
EY-
IN-1
RE
MO
TE
RE
SE
TR
ES
ET
Q15
1
P-O
N+
3.3V
(D)
42 43X
161
27M
Hz
XIN
XO
UT
MA
IN C
BA
LC
D M
AIN
CB
A U
NIT
4
KE
Y-IN
-21
1
KE
Y-IN
-2
22 1817BA
CKLI
GHT-S
W19
5BA
CKLI
GHT-A
DJ21
3P
-ON
-H16
8
VO
LUM
E15
9AU
DIO
-MU
TE13
11
INP
UT-
012
12IN
PU
T-1
1113
S-S
W7
17S
CL
618
SD
A5
19
BA
CK
LIG
HT-
SW
BA
CK
LIG
HT-
AD
J
P-O
N-H
VO
LUM
EA
UD
IO-M
UT
E
SD
AS
CL
INP
UT-
0IN
PU
T-1
S-S
WS
CL
SD
A
20 3531 401932 41TO
PO
WE
R S
UP
PLY
BLO
CK
DIA
GR
AM
TO IF
/VID
EO
BLO
CK
DIA
GR
AM
TO A
UD
IOB
LOC
K D
IAG
RA
M
BA
CK
LIG
HT-
SW
BA
CK
LIG
HT-
AD
JP
-ON
-H
VO
LUM
EA
UD
IO-M
UT
E
INP
UT-
0IN
PU
T-1
S-S
WS
CL
SD
A
TO L
CD
BA
CK
LIG
HT
BLO
CK
DIA
GR
AM
CN
102B
CN
102A
IC17
1(M
EM
OR
Y)
SC
L6
SD
A57
WP
Q13
13.
3V<
-->
5V
CO
NV
ER
TE
R
23B
US
-OP
EN
P-O
N-H
2(N
U)
1410
16P
-ON
-H2
12P
-25V
-ON
P-2
5V-O
N
TO P
OW
ER
SU
PP
LYB
LOC
K
DIA
GR
AM
KE
Y S
WIT
CH
IR S
EN
SO
R C
BA
CLN
105
RE
MO
TE
SE
NS
OR
RC
V91
AL
+5V D
91P
OW
ER
Q91
P-O
N-H
44
CN
105
RE
MO
TE
33
INV
ER
TE
R C
BA
BACK
LIGH
T-ADJ
99
CN
411
CLN
411
BACK
LIGH
T-SW
88
P-O
N-H
1111
P-O
N-H
AF
T-IN
1014
5A
FT-
IN
80T
UN
ER
CLK
Q30
1B
UF
FE
RA
FT-
IN
BU
S-O
PE
N5
19
CN
103B
CN
103A
CN
113
(NO
CO
NN
EC
TIO
N)
SD
A2
SC
L1
BU
S-O
PE
N4
CN
113
IS U
SE
D
FO
R A
DJU
ST
ME
NT
A
T F
AC
TO
RY
P-O
N-H
FS
C1
23
FS
C
7-2 L3222BLIF
IF/Video Block Diagram
TO A
UD
IOB
LOC
K D
IAG
RA
M
CN
103A
TO LCD
BLO
CK
DIA
GR
AM
CN
103B
CV
BS
11S
-VID
EO
-C7
S-V
IDE
O-Y
9
INP
UT-
0(IN
V)
INP
UT-
1(IN
V)
SA
WF
ILT
ER
TU
1S
F11
IF
AG
C
SD
AS
CL
17 32
SIF
MA
IN C
BA
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
TO A
UD
IO B
LOC
KD
IAG
RA
M
JK70
6V
IDE
O-Y
IN JK70
7V
IDE
O-P
b/C
bIN JK
708
VID
EO
-Pr/
Cr
IN
JK70
3V
IDE
O1
-IN
JK70
1S
-VID
EO
IN
BU
FF
ER
Q32
SD
ATO S
YS
TE
M
CO
NT
RO
L B
LOC
KD
IAG
RA
M
SC
L
S-S
W
CY
CN
103A
TO LCD
BLO
CK
DIA
GR
AM
CN
103B
VID
EO
-Y5
VID
EO
-Pb/
Cb
3V
IDE
O-P
r/Cr
1
3
IC78
1(I
NP
UT
SE
LEC
T)
5
Q70
3
4
13 12
Q70
2
14
1 2
Q70
1
15
SW
CO
NT
RO
L
109
11
INP
UT-
0
INP
UT-
1TO
SY
ST
EM
CO
NT
RO
LB
LOC
K D
IAG
RA
M
Q70
7
Q70
8
Q70
4
Q70
5
Q70
6
(TU
NE
R U
NIT
)
BU
FF
ER
BU
FF
ER
BU
FF
ER
BU
FF
ER
BU
FF
ER
BU
FF
ER
WF
7
WF
8
WF
9
WF
10
WF
11
WF
12
CF
31IC
31(I
F S
IGN
AL
PR
OC
ES
S)
VIF
AM
PV
IDE
OD
ET
VC
O
4.5M
Hz
FIL
TE
R
RF
AG
C
AM
P
SIF
AM
P16
1318
174
78
1
XTA
L-IN
14
TO S
YS
TE
M C
ON
TR
OL
BLO
CK
DIA
GR
AM
AF
T-IN
5
SIF
TR
AP
11
IF A
GC
DE
T
AF
TE
QA
MP
2
DE
FE
AT
FS
C
7-3
Audio Block Diagram
L3222BLA
MA
IN C
BA
AU
DIO
SIG
NA
L
AU
DIO
-MU
TE
VO
LUM
ETO
SY
ST
EM
C
ON
TR
OL
BLO
CK
INP
UT-
0(IN
V)
INP
UT-
1(IN
V)
SC
LS
DA
IC85
2(I
NP
UT
SE
LEC
T)
SW
CT
L
3
11 15 12 4 1
910
ST
ER
EO
FIL
TE
R75
uSD
E-E
MP
H
dBX
DE
-EM
PH
L+R
FIL
TE
R
WID
E B
AN
DF
ILT
ER
WID
E B
AN
DR
MS
DE
TW
IDE
BA
ND
EX
PAN
D
SP
EC
TR
AL
EX
PAN
D
SP
EC
TR
AL
RM
S D
ET
SP
EC
TR
AL
FIL
TE
R
OF
FS
ET
CA
NC
EL
L-C
H
R-C
H
MAT
RIX
AG
CO
FF
SE
TC
AN
CE
LL-
RF
ILT
ER
(L-R
)/S
AP
SW
SA
PF
ILT
ER
I2C
DE
CO
RD
ER
SA
PD
EM
OD
SA
P O
UT
FIL
TE
R
2930TO
IF
/VID
EO
BLO
CK
DIA
GR
AM
TU
NE
R
TU
NE
R(L-C
H)
(R-C
H)
21 2724
IC85
1(M
TS
/SA
P A
UD
IO S
IGN
AL
PR
OC
ES
S)
AU
DIO
1(L)
-IN
JK70
4
SIF
JK70
5A
UD
IO1(
R)
-IN
JK70
9A
UD
IO2(
L)-I
N
JK71
0A
UD
IO2(
R)
-IN
OF
FS
ET
CA
NC
EL
14
IC80
1 (A
UD
IO A
MP
)
7
VO
LUM
E
11 A
MP
AM
P
MU
TE
/STA
ND
BY
CO
NT
RO
L
6 1(R
-CH
)
(L-C
H)
2
Q80
2Q80
3
5RF
JK80
1H
EA
DP
HO
NE
JAC
K SP
801
SP
EA
KE
RR
-CH
CN
801
SP
-R1
GN
D2
SP
802
SP
EA
KE
RL-
CH
CN
802
CLN
802
CLN
801
SP
-L1
GN
D2
+5V
TO IF
/VID
EO
B
LOC
K D
IAG
RA
M
13
2
WF
6
AU
DIO
1
AU
DIO
2
AU
DIO
1A
UD
IO2
SIF
/BB
SW
INP
UT
VC
AS
IFD
EM
OD
14 5
P-O
N-H
7-4
LCD Block Diagram
L3222BLLCD
CN
311
TO IF/V
IDE
OB
LOC
KD
IAG
RA
MC
N10
3A
OR
(0)
34O
R(1
)33
LC
D M
AIN
CB
A U
NIT
VID
EO
SIG
NA
L
CV
BS
13S
-VID
EO
-C17C
N10
3B
IC33
3(L
CD
DR
IVE
/ S
IGN
AL
PR
OC
ES
S)
68 49 71
S-V
IDE
O-Y
15
TO IF/V
IDE
OB
LOC
KD
IAG
RA
MC
N10
3A
VID
EO
-Y19
VID
EO
-Pb/
Cb
21CN
103B
LCD
MO
DU
LE
OR
(2)
32O
R(3
)31
OR
(4)
30O
R(5
)29
OG
(0)
27O
G(1
)26
OG
(2)
25O
G(3
)24
OG
(4)
23O
G(5
)22
OB
(0)
20O
B(1
)19
OB
(2)
18O
B(3
)17
OB
(4)
16O
B(5
)15
ER
(0)
6E
R(1
)5
ER
(2)
4E
R(3
)3
ER
(4)
2E
R(5
)1
EG
(0)
50E
G(1
)49
EG
(2)
48E
G(3
)47
EG
(4)
46E
G(5
)45
EB
(0)
43E
B(1
)42
EB
(2)
41E
B(3
)40
EB
(4)
39E
B(5
)38
OF
FE
V12
ST
V1
13C
LKV
14
HM
S1-
E7
HM
S1-
013
ST
H1
42P
OL
43LP
44
CN
311
170
605274
169
166
165
164
163
162
161
157
156
155
154
153
152
148
147
146
145
138
137
136
135
130
129
128
127
126
125
118
117
116
115
114
113
108
107
101
105
106
144
139
172
173
174
A/D
VID
EO
SIG
NA
LP
RO
CE
SS
LCD
RG
BS
IGN
AL
PR
OC
ES
S
R BG Y Pb/
Cb
Pr/
Cr
B(E
VE
N)
G(E
VE
N)
R(E
VE
N)
B(O
DD
)
G(O
DD
)
R(O
DD
)
CN
312
A/D
A/D
A/D
A/D
A/D
VID
EO
-Pr/C
r23
R BG
WF
3
OD
DIN
V
EV
EN
INV
ST
H-1
PO
LLP
OF
FE
VS
TV
1C
LKV
CLK
H10
143
CLK
H1
WF
1
WF
5
WF
2
CV
BS
C Y
R20
1R
202
R39
4
R36
5
R39
2
WF
4
7-5
Power Supply Block Diagram
L3222BLP
4A/1
25V
F60
14A
/125
VLI
NE
FIL
TE
R
L601
AC
601
AC
CO
RD
BR
IDG
ER
EC
TIF
IER
D60
5 -
D60
8HO
TC
OL
DT
601
1512131411167
4 3
1 2
IC60
1E
RR
OR
VO
LTA
GE
DE
T
Q60
1
Q60
3S
WIT
CH
ING
CO
NT
RO
L
SW
ITC
HIN
G
MA
IN C
BA
5 3 2
PAN
EL+
3.3V
46
PAN
EL+
10.8
V5
5
PAN
EL+
25V
73
PAN
EL-
6V8
2
VT
+33
V
Q51
1Q51
3
IC53
3
+5V
RE
G.
HO
T C
IRC
UIT
. BE
CA
RE
FU
L. LI
NE
FIL
TE
R
L602
AL+
13V
Q50
9
Q50
5
Q51
0
Q51
2
CN
101A
P-2
5V-O
N21
3A
L+5V
222
CN
102A
Q50
2
Q50
1
IC67
1
+5V
RE
G.
IC67
2
+5V
RE
G.
RE
G+
5V
RE
G+
5V
IC53
1
+7V
RE
G.
Q53
1
P-O
N-H
9 10
AL+
21V
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
D
IAG
RA
M
TP
401
+21
V
Q63
3
CN
101B
PAN
EL+
3.3V
PAN
EL+
10.8
V
PAN
EL+
25V
PAN
EL-
6V
LC
D M
AIN
CB
A U
NIT
P-2
5V-O
NA
L+5V
CN
102B
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
D
IAG
RA
M
TO L
CD
BA
CK
LIG
HT
BLO
CK
D
IAG
RA
M
CN
103A
CN
103B
AL+
7V(D
)21
3IC
191
+3.
3V
RE
G.
IC19
2+
1.5V
R
EG
.
IC19
3+
3.3V
R
EG
.
AL+
3.3V
(D)
AL+
1.5V
(D)
AL+
3.3V
(A)
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
601)
is b
low
n , c
heck
to s
ee th
at a
ll co
mpo
nent
s in
the
pow
er s
uppl
yci
rcui
t are
not
def
ectiv
e be
fore
you
con
nect
the
AC
plu
g to
the
AC
pow
er s
uppl
y.O
ther
wis
e it
may
cau
se s
ome
com
pone
nts
in th
e po
wer
sup
ply
circ
uit t
o fa
il.
For
con
tinue
d pr
otec
tion
agai
nst r
isk
of fi
re,
repl
ace
only
with
sam
e ty
pe 4
A, 1
25V
fuse
.C
AU
TIO
N !
:
AT
TE
NT
ION
: U
tilis
er u
n fu
sibl
e de
rec
hang
e de
mêm
e ty
pe d
e 4
A, 1
25V
.4A
/125
V
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
7-6
LCD Backlight Block Diagram
L3222BLIV
CU
RR
EN
TC
ON
TR
OL
SW
ITC
H
CU
RR
EN
TC
ON
TR
OL
SW
ITC
H
BA
CK
LIG
HT-
SW
RL4
01
Q42
1,Q
426
IC40
1 (D
C-A
C IN
VE
RT
ER
CO
NT
RO
L)
Q40
3
Q41
2
VC
C
1 2
T45
0
CN
450
LC
D M
OD
UL
EIN
VE
RT
ER
CB
A
P-O
N-H
BA
CK
LIG
HT-
AD
J
Q43
3
Q41
1
BA
CK
LIG
HT
BA
CK
LIG
HT
BA
CK
LIG
HT
26 27 23 24 28 14 11 913 12
116
+8V
RE
G.
OU
TP
UT
LOG
IC1
OU
TP
UT
LOG
IC2
LOG
IC
OV
ER
VO
LTA
GE
PR
OT
EC
T
SLO
WS
TAR
T
OS
C
PW
M2
PW
M1
STA
ND
BY
MO
DE
SW
4 5 7
OV
ER
VO
LTAG
EP
RO
TEC
TOR
Q45
1,45
2
OV
ER
VO
LTAG
EP
RO
TEC
TOR
Q45
4,45
5
76
98
12
1314
T49
0C
N49
0
OV
ER
VO
LTAG
EP
RO
TEC
TOR
Q49
1,49
2
1 2 1 2
T46
0C
N46
0
OV
ER
VO
LTAG
EP
RO
TEC
TOR
Q46
1,46
2
10
IC40
2(O
P A
MP
)
TO SY
ST
EM
CO
NT
RO
LB
LOC
KD
IAG
RA
M
AL+
21V
9 7
3 1 64 2 5
10 8 9 7
3 1 64 2 5
10 8 9 7
3 1 64 2 5
10 8
TO PO
WE
RS
UP
PLY
BLO
CK
DIA
GR
AM
MA
IN C
BA
AL+
21V
22
CN
411
CLN
411
AL+
21V
11
AL+
21V
33
8-1 LC2N_SC
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS
Standard NotesMany electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P = 10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
Note of Capacitors:ML --- Mylar Cap. PP --- Metallized Film Cap. SC --- Semiconductor Cap. L --- Low Leakage type
Temperature Characteristics of Capacitors are noted with the following:B --- ±10% CH --- 0±60 ppm/°C CSL --- +350~-1000 ppm/°C
Tolerance of Capacitors are noted with the following:Z --- +80~-20%
Note of Resistors:CEM --- Cement Res. MTL --- Metal Res. F --- Fuse Res.
Capacitors and transistors are represented by the following symbols.
(Top View) (Bottom View)
(Bottom View)
Electrolytic Capacitor+
Transistor or Digital Transistor
NPN Transistor PNP Transistor
NPN Digital Transistor PNP Digital Transistor
(Top View)
(Top View)
E C B
E C B
Digital Transistor
CBA Symbols Schematic Diagram Symbols
E C B
(Top View)
(Top View)
E C B
E C B
8-2 LC2N_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.:
5. How to read converged lines
6. Test Point Information
2 315.0
(3.0)5.0
(3.0)
Voltage Indicates that the voltage is not consistent here.
Power on modePower off mode
(Unit: Volt)
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
8-3
Main 1/4 Schematic Diagram
L3222SCM1
MAIN 1/4
Ref No. Position
IC531 D-4
IC533 E-3
IC671 E-2
IC672 E-2
Q501 C-4Q502 C-4Q503 B-3Q505 C-3Q509 C-3Q510 B-2Q511 C-3Q512 C-2Q513 C-2Q531 D-3Q633 E-1
CN411 F-4CN101A A-4CN102A A-3
TP401 E-4
ICS
TRANSISTORS
TEST POINT
CONNECTORS
8-4 L3222SCM2
Main 2/4 Schematic DiagramMAIN 2/4
Ref No. Position
IC31 I-1IC851 H-3IC852 J-4
Q32 J-2
CN113 G-1
ICS
TRANSISTOR
CONNECTOR
8-5
Main 3/4 Schematic Diagram
L3222SCM3
MAIN 3/4Ref No. Position
IC781 P-3
IC801 N-2
Q701 N-3
Q702 N-3Q703 N-3Q704 P-1Q705 O-1Q706 P-1
Q707 P-2
Q708 P-2
Q802 O-1
Q803 N-1
CN801 M-4
CN802 M-3CN103A M-2
ICS
TRANSISTORS
CONNECTORS
8-6 L3222SCM4
Main 4/4 Schematic Diagram
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
MAIN 4/4Ref No. Position
IC601 U-1
Q601 S-2Q603 T-2
TRANSISTORS
IC
8-7 L3222SCI
Inverter Schematic DiagramINVERTER
Ref No. Position
IC401 A-3
IC402 E-3
Q403 B-1Q411 B-3Q412 B-3Q421 B-4Q426 B-3Q433 B-2Q451 E-4Q452 D-4Q454 D-3Q455 D-3Q461 E-2Q462 D-2Q491 D-3Q492 D-3
CLN411 A-1
CN450 F-4
CN460 F-2CN490 F-4
ICS
TRANSISTORS
CONNECTORS
8-8 L3222SCF
Function Schematic Diagram
8-9 L3222SCIR
IR Sensor Schematic Diagram
8-10 L3222SCL1
LCD Main 1/2 Schematic DiagramLCD MAIN 1/2
Ref No. Position
IC333 B-3
Q301 D-1
CN104 A-3
CN105 A-2
CN211 F-4CN311 F-4
CN102B A-4
CONNECTORS
IC
TRANSISTOR
8-11 L3222SCL2
LCD Main 2/2 Schematic DiagramLCD MAIN 2/2
Ref No. Position
IC151 I-3
IC171 J-3
IC191 H-2
IC192 H-1IC193 H-2IC201 J-1
Q131 I-4
Q201 J-1
CN112 L-4
CN312 L-3
CN101B L-4CN103B G-2
ICS
CONNECTORS
TRANSISTORS
8-12
TP401+21V
BL3100F01013-1
Main CBA Top View
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
8-13
PIN 9 OFCN103A
WF8
Q706Emitter
WF12
WF9
PIN 7 OFCN103A
Q704Emitter
WF10
Q705Emitter
WF11
PIN 11 OFCN103A
WF7
WF6
PIN 14OF IC801
Main CBA Bottom View
BL3100F01013-1
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
MAIN CBARef No. Position
IC31 E-4
IC531 E-3
IC533 E-3IC601 A-5
IC671 E-4
IC672 E-3
IC781 D-2
IC801 D-5
IC851 D-2IC852 E-2
Q32 E-4Q501 C-2Q502 C-2Q503 C-2
Q505 C-4
Q509 C-3
Q510 C-3
Q511 C-2Q512 C-2Q513 C-3Q531 C-2Q601 B-5
Q603 B-5
Q633 A-5
Q701 D-2
Q702 D-2Q703 D-2Q704 E-1Q705 E-1Q706 E-2
Q707 E-2
Q708 E-2
Q802 E-5
Q803 D-5
CN113 E-1
CN411 B-2
CN801 E-5
CN802 A-5CN101A C-2CN102A D-2CN103A D-2
TP401 B-3TEST POINT
TRANSISTORS
CONNECTORS
ICS
8-14
BL3100F01022-3
Function CBA Top View
Function CBA Bottom View
IR Sensor CBA Top & Bottom View
BL3100F01022-2
BL3100F01022-2
8-15
Inveretr CBA Top View
Inverter CBA Bottom View
BL3100F01022-1
INVERTERRef No. Position
IC401 D-1
IC402 E-1
Q403 C-1Q411 D-1Q412 D-2Q421 D-1Q426 D-1Q433 A-1Q451 E-1Q452 E-1Q454 E-1Q455 E-1Q461 A-1Q462 A-1Q491 E-2Q492 E-2
CLN411 C-1
CN450 C-2
CN460 A-2CN490 D-2
ICS
TRANSISTORS
CONNECTORS
WAVEFORMS
L3222WF9-1
1DIV: 1.0V 10 s
1DIV: 1.0V 20 s
R392WF1 1DIV: 1.0V 10 s
R394WF5
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
WF1 ~ WF12 = Waveforms to be observed atWaveform check points.(Shown in Schematic Diagram.)
1DIV: 1.0V 20nsR365
WF2
R202WF3 1DIV: 200mV 20 s
Pin 11 of CN103AWF7
1DIV: 200mV 20 sPin 9 of CN103A
WF8
1DIV: 100mV 400 sPin 14 of IC801
WF6
1DIV: 1.0V 10 sR201
WF4
1DIV: 200mV 20 sPin 7 of CN103A
WF9
1DIV: 200mV 20 sQ704 Emitter
WF10
1DIV: 200mV 20 sQ705 Emitter
WF11
1DIV: 200mV 20 sQ706 Emitter
WF12
CLKH
CLKV
POL
LP
STH1
AUDIO
CVBS
S-VIDEO-Y
S-VIDEO-C
VIDEO-Y
VIDEO-Pb/Cb
VIDEO-Pr/Cr
WIRING DIAGRAM
L3222WI10-1
LC
D M
OD
UL
E
LC
D M
AIN
CB
A U
NIT
NU
GN
D
PAN
EL+
25V
PAN
EL+
10.8
V
GN
DN
U
PAN
EL-
6V
GN
D
PAN
EL+
3.3V
CN
101B
15 39 7 24681 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23
BA
CK
LIG
HT-
AD
J
NU
GN
D
GN
DB
AC
KLI
GH
T-S
WN
UN
UP
-ON
-H
AU
DIO
-MU
TE
VO
LUM
EP
-ON
-H2(
NU
)
INP
UT-
0
PR
OT
EC
T-1
INP
UT-
1A
FT-
IN
PR
OT
EC
T-2
SD
A
S-S
WS
CL
GN
DP
-25V
-ON
GN
DA
L+5V
CN
102A
BA
CK
LIG
HT-
AD
J
CN
102B NU
GN
D
GN
DB
AC
KLI
GH
T-S
W NU
NU
P-O
N-H
AU
DIO
-MU
TE
VO
LUM
EP
-ON
-H2(
NU
)
INP
UT-
0
PR
OT
EC
T-1
INP
UT-
1A
FT-
IN
PR
OT
EC
T-2
SD
A
S-S
WS
CL
GN
DP
-25V
-ON
GN
DA
L+5V
15 39 7 24681014 1218 16 111315171923 21 2022
TU
1 T
UN
ER
UN
IT
CN
312
1G
ND
2N
U3
V-C
OM
4V
-CO
M5
NU
6V
DD
G(+
25V
)7
NU
8V
DD
D(+
3.3V
)9
NU
10V
EE
G(-
6V)
11N
U12
OF
FE
V13
ST
V1
14C
LKV
15N
U16
GN
D17
NU
18N
U19
NU
20N
U21
GN
D22
VR
EF
(9)
23V
RE
F(8
)24
VR
EF
(7)
25V
RE
F(6
)26
VR
EF
(5)
27G
ND
28V
RE
F(4
)29
VR
EF
(3)
30V
RE
F(2
)31
VR
EF
(1)
32V
RE
F(0
)33
VD
DA
(+10
.8V
)34
VD
DA
(+10
.8V
)35
V-C
OM
36V
-CO
M37
GN
D38
EB
(5)
39E
B(4
)40
EB
(3)
41E
B(2
)42
EB
(1)
43E
B(0
)44
GN
D45
EG
(5)
46E
G(4
)47
EG
(3)
48E
G(2
)49
EG
(1)
50E
G(0
)
VID
EO
-Y I
N
AU
DIO
1(R
)-I
N
AU
DIO
2(L)
-IN
S-V
IDE
OO
UT
IN
VID
EO
-Pb/
Cb
IN
VID
EO
-Pr/
Cr
IN
VID
EO
1-I
N
AU
DIO
1(L)
-IN
AU
DIO
2(R
)-I
N
IR S
EN
SO
R C
BA
MA
IN C
BA
FU
NC
TIO
N C
BA
5N
U
1 3
CLN
105
42R
EM
OT
E
AL+
5VG
ND
P-O
N-H
5N
U
1 3 42
CN
105
RE
MO
TE
AL+
5VG
ND
P-O
N-H
INV
ER
TER
CB
A
BA
CK
LIG
HT
CN
450
21
BA
CK
LIG
HT
CN
490
21
CN
311 1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23 24 272625 28 29 30
GN
DC
LKH
GN
DG
ND
HM
S1-
EE
R(0
)E
R(1
)E
R(2
)E
R(3
)E
R(4
)E
R(5
)
GN
DH
MS
1-0
GN
DO
B(5
)O
B(4
)O
B(3
)O
B(2
)O
B(1
)O
B(0
)G
ND
OG
(5)
OG
(4)
OG
(3)
OG
(2)
OG
(1)
OG
(0)
GN
DO
R(5
)O
R(4
)
333231 34 35 3736 3938 4140 42 43 44 45
OR
(3)
OR
(2)
OR
(1)
OR
(0)
GN
DG
ND
VD
DD
(+3.
3V)
VD
DD
(+3.
3V)
VD
DD
(+3.
3V)
VD
DD
(+3.
3V)
GN
DS
TH
1P
OL
LP GN
DB
AC
KLI
GH
T
CN
460
21
CLN
801
SP
801
SP
EA
KE
R1
CN
801
2S
P-R
GN
D
CLN
802
SP
802
SP
EA
KE
R1
CN
802
2S
P-L
GN
D
21 53 97
CN
101A
4 6 8PA
NE
L+25
V
PAN
EL+
10.8
V
NU
GN
D
GN
DPA
NE
L+3.
3V
GN
D
PAN
EL-
6VNU
1 53 97
CN
103A
2 4 6 8 10 1412 181611 13 15 17
VID
EO
-Pb/
Cb
S-V
IDE
O-C
GN
D
GN
DS
-VID
EO
-Y
CV
BS
19 232120 22
GN
D
GN
D
GN
DV
IDE
O-Y
VID
EO
-Pr/
Cr
GN
D
GN
DA
L+7V
(D)
BU
S-O
PE
N
NU
GN
D
NU
GN
D
NU
AL+
3.3V
(A)
DVD-
MAIN
-POW
ER(N
U)
FS
C15 39 7 2468
CN
103B
1014 1218 16 111315171923 21 2022V
IDE
O-P
b/C
b
S-V
IDE
O-C
GN
D
GN
DS
-VID
EO
-Y
CV
BS
GN
D
GN
D
GN
DV
IDE
O-Y
VID
EO
-Pr/
Cr
GN
D
GN
DA
L+7V
(D)
BU
S-O
PE
N
NU
GN
D
NU
GN
D
NU
AL+
3.3V
(A)
DVD-
MAIN
-POW
ER(N
U)
FS
C
AC
601
AC
CO
RD
1 32 4
CN
104
KE
Y-IN
-2
AL+
3.3V
(D)
KE
Y-IN
-1
GN
D5 76 8
NU
NU
NU
NU
1 53
CN
411
2 4 6
AL+
21V
GN
D
AL+
21V
AL+
21V
GN
D
GN
D
97 8 10B
ACK
LIG
HT-
AD
J
GN
D
PR
OT
EC
T-1
BAC
KLI
GH
T-S
W
11P
-ON
-H
1 532 4 6
CLN
411
AL+
21V
GN
D
AL+
21V
AL+
21V
GN
D
GN
D
97 8 10B
ACK
LIG
HT-
AD
J
GN
D
PR
OT
EC
T-1
BAC
KLI
GH
T-S
W
11P
-ON
-H
1 3
CLN
104
2 4
KE
Y-IN
-2
AL+
3.3V
(D)
KE
Y-IN
-1
GN
D5
NU
11-1 L3222CEX
EXPLODED VIEWS
Cabinet
A9
B24
L1
L1
L1
L3
B10
B6
B7L3
L3
L3
L3 L3
L3
L4
L9
B4
L1L1
L3L3
L3
L17
L2L2
L18
L2
L2
L2
L2
L2
L1
L10
L2
L2
L6A8A6
B12
B3A4
B21
B21
A10
S5B5
B5B21
L17
A3
A2
A11
B1
L1
L1
A1 A7
L1
B1
L1
L1
B6
B6B6
B6
B24
B23
B22
LCD Main CBA & Liquid Crystal Panel Unit
See Electrical Parts List for parts with this mark.
IR Sensor CBA
SP801
CLN801
SP802
CLN802
Function CBA
Main CBAInverter CBA
AC601
11-2 L3222PEX
Packing
S1
FRONT
S2
S5
S4
Tape
Tape
Packing Tape
Packing Tape
Packing Tape
S3
S6
X1
X4X3
Some Ref. Numbers are not in sequence.
X2
20051125 12-1 L3222CA
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Ref. No. Description Part No.
A1 FRONT CABINET L3200UA 1EM020185
A2 BRAND BADGE L0203UD~EMERSON~ 0EM409020
A3 CONTROL PLATE L0301UB 1EM220019
A4 REAR CABINET L3200UA 1EM020138
A6# RATING LABEL L3222UC ----------
A7 FUNCTION KNOB L0301UB 1EM220005A
A8 REAR COVER L3207UH 1EM420953
A9 TILT STAND ASSEMBLY L0301UB 1EMN20039A
A10 CONNECTOR CAP L3200UA 1EM420645
A11 SENSOR/LED LENS L0301UB 1EM220004
B1 SPEAKER HOLDER L0110UA 0EM407855C
B3 STAND HOLDER L0200UA 0EM301999B
B4 JACK HOLDER L3201UB 1EM120107
B5 CLOTH(10X30XT0.5) B5900UA 0EM404486
B6 CLOTH(15X190XT 0.5) L0100JA 0EM407894
B12 20V TILT STAND HOLDER L4200EA 1EM320145
B21 CLOTH(10X180XT0.5) L0336JG 0EM408827
B22 INSULATION PLATE L3207UH 1EM421108
B23# CAUTION LABEL L3207UH ----------
B24 CLOTH(20X65XT0.5) L0100JA 0EM407914
CLN801 SPEAKER WIRE ASSEMBLY 2P WIRE ASSEMBLY
WX1L3201-001
CLN802 SPEAKER WIRE ASSEMBLY 2P WIRE ASSEMBLY
WX1L3201-001
L1 SCREW P-TIGHT 3X14 WASHER HEAD+ GCMP3140
L2 SCREW P-TIGHT 3X12 BIND HEAD+ GBMP3120
L3 SCREW S-TIGHT M3X8 BIND HEAD+ GBMS3080
L6 DOUBLE SEMS SCREW M4X9 L0130UA 0EM408146
L9 SCREW P-TIGHT 3X10 BIND HEAD+ GBKP3100
L10 P-TIGHT SCREW 3X8 BIND + GBMP3080
L17 SCREW S-TIGHT M3X8 BIND HEAD + BLK GBKS3080
L18 DOUBLE SEMS SCREW M4X12 + BLAK FPK34120
SP801 SPEAKER S0407F10 DSD0807XQ002
SP802 SPEAKER S0407F10 DSD0807XQ002
PACKINGS1 CARTON L3212UC 1EM421900
S2 STYROFOAM TOP L0301UB 1EM020018A
S3 STYROFOAM BOTTOM L0301UB 1EM020019A
S4 SET BAG L3207UH 1EM320295
S5 SERIAL NO. LABEL L9750UA ----------
S6 STYROFOAM STAND BOTTOM L0301UB 1EM020020A
ACCESSORIESX1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A
X2# OWNER S MANUAL L3212UC 1EMN20869
X3 REMOTE CONTROL 170/ECNLC301/NE900UD NE900UD
X4 DRY BATTERY R03/2S XB0M451T0006
20051125 13-1 L3222EL
ELECTRICAL PARTS LISTPRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
LCD MAIN CBA & LIQUID CRYSTAL PANEL UNIT
MAIN CBA
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
LCD MAIN CBA & LIQUID CRYSTAL PANEL UNIT
1FSA10076
Ref. No. Description Part No.
MAIN CBAConsists of the following:
1ESA11493
CAPACITORSC11 ELECTROLYTIC CAP. 10µF/50V M CA1J100SP085
C12 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C13 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C14 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C15 ELECTROLYTIC CAP 1µF/50V M CA1J1R0SP085
C16 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C21 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C22 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMASSM101
C23 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C24 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C25 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C26 PCB JUMPER D0.6-P5.0 JW5.0T
C27 FILM CAP.(P) 0.018µF/50V J CA1J183MS029
C28 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473
C29 CHIP CERAMIC CAP. CH D 3pF/50V CHD1JD3CH3R0
C30 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C31 PCB JUMPER D0.6-P5.0 JW5.0T
C32 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMASSM101
C34 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C35 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMASSM1R0
C36 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C37 CHIP CERAMIC CAP. CH J 680pF/50V CHD1JJ3CH681
C39 ALUMINUM ELECTROLYTIC CAP 0.47µF/50V H7
CE1JMASSMR47
C41 ELECTROLYTIC CAP. 4.7µF/50V M CA1J4R7SP085
C42 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C43 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C44 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMASSM101
C45 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C46 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
C501 ELECTROLYTIC CAP. 22µF/50V M CA1J220SP085
C502 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C503 ELECTROLYTIC CAP. 220µF/16V M CA1C221SP085
C504 ELECTROLYTIC CAP. 100µF/10V M CA1A101SP085
C505 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C506 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C507 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C508 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C515 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C531 ELECTROLYTIC CAP. 330µF/50V M CA1J331SP084
C532 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C534 CHIP CERAMIC CAP. B K 1µF/16V CHD1CK30B105
C535 ELECTROLYTIC CAP. 470µF/16V M CA1C471SP085
C537 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C538 ELECTROLYTIC CAP. 10µF/50V M CA1J100SP085
C539 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C601# METALIZED FILM CAP. 0.1µF/250V CT2E104MS037
C602# METALIZED FILM CAP. 0.1µF/250V CT2E104MS037
C605 CERAMIC CAP. F Z 0.01µF/500V CCD2JZP0F103
C606 CERAMIC CAP. F Z 0.01µF/500V CCD2JZP0F103
C608 CERAMIC CAP. B K 1000pF/2KV CCD3DKP0B102
C610# ELECTROLYTIC CAP. 100µF/200V M CE2DMZPDL101
C612 FILM CAP.(P) 0.01µF/50V J CMA1JJS00103
C613 FILM CAP.(P) 0.056µF/50V J CMA1JJS00563
C614 PCB JUMPER D0.6-P5.0 JW5.0T
C615 PCB JUMPER D0.6-P5.0 JW5.0T
C630# ELECTROLYTIC CAP. 2200µF/25V M CA1E222SP084
C631# ELECTROLYTIC CAP. 2200µF/35V M CA1G222SP084
C633# ELECTROLYTIC CAP. 220µF/16V M CA1C221SP085
C634# ELECTROLYTIC CAP. 1000µF/25V M CA1E102SP084
C635# ELECTROLYTIC CAP. 470µF/10V M CA1A471SP085
C636 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C637# ELECTROLYTIC CAP. 2200µF/35V M CA1G222SP084
C638 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C641# SAFETY CAP. 4700pF/250V KX CA2E472MR050
C642# ELECTROLYTIC CAP. 10µF/50V M CA1J100SP085
C644# ELECTROLYTIC CAP 100µF/50V M CA1J101SP085
C645# ELECTROLYTIC CAP. 10µF/50V M CA1J100SP085
C646 MYLAR CAP. 0.22µF/50V J CMA1JJS00224
C649 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C650 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C652# ELECTROLYTIC CAP. 1000µF/25V M CA1E102SP084
C654# ELECTROLYTIC CAP. 100µF/200V M CE2DMZPDL101
C657 ALUMINUM ELECTROLYTIC CAP 47µF/16V H7 CE1CMASSM470
C659 FILM CAP.(P) 0.022µF/50V J CMA1JJS00223
C660 FILM CAP.(P) 0.0068µF/50V J CMA1JJS00682
C671 ELECTROLYTIC CAP. 470µF/10V M CA1A471SP085
C672 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C673 ELECTROLYTIC CAP. 470µF/10V M CA1A471SP085
C674 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C701 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C702 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C703 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
C704 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
C705 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C706 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C707 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C708 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C711 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
C712 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
Ref. No. Description Part No.
20051125 13-2 L3222EL
C713 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332
C714 CHIP CERAMIC CAP. F Z 2.2µF/10V CHD1AZ30F225
C715 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332
C716 CHIP CERAMIC CAP. F Z 2.2µF/10V CHD1AZ30F225
C722 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
C726 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
C730 ELECTROLYTIC CAP. 47µF/16V M CA1C470SP085
C734 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C735 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C736 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C738 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C739 ELECTROLYTIC CAP. 100µF/10V M CA1A101SP085
C740 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C751 CHIP CERAMIC CAP. F Z 2.2µF/10V CHD1AZ30F225
C752 CHIP CERAMIC CAP. F Z 2.2µF/10V CHD1AZ30F225
C753 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332
C754 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332
C781 ELECTROLYTIC CAP. 10µF/50V M CA1J100SP085
C782 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C784 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C785 ELECTROLYTIC CAP. 100µF/10V M CA1A101SP085
C787 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C801 ELECTROLYTIC CAP. 470µF/16V M CE1CMZPDL471
C802 ELECTROLYTIC CAP. 470µF/16V M CA1C471SP085
C803 FILM CAP.(P) 0.1µF/50V J CMA1JJS00104
C804 FILM CAP.(P) 0.1µF/50V J CMA1JJS00104
C805 ELECTROLYTIC CAP. 10µF/50V M CA1J100SP085
C806 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C807 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C809 ELECTROLYTIC CAP. 4.7µF/50V M CA1J4R7SP085
C811 ELECTROLYTIC CAP. 100µF/16V M CA1C101SP085
C812 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C813 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C818 ELECTROLYTIC CAP. 2200µF/16V M CA1C222SP084
C819 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C820 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C851 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C852 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C853 ELECTROLYTIC CAP. 2.2µF/50V M CA1J2R2SP085
C854 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C855 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C856 CHIP CERAMIC CAP.(1608) B K 0.33µF/10V CHD1AK30B334
C857 ELECTROLYTIC CAP. 2.2µF/50V M CA1J2R2SP085
C858 ELECTROLYTIC CAP. 2.2µF/50V M CA1J2R2SP085
C859 ELECTROLYTIC CAP. 4.7µF/50V M CA1J4R7SP085
C860 ELECTROLYTIC CAP. 10µF/50V M CA1J100SP085
C861 ELECTROLYTIC CAP. 100µF/10V M CA1A101SP085
C862 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C863 ELECTROLYTIC CAP. 2.2µF/50V M CA1J2R2SP085
C864 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C865 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C866 CHIP CERAMIC CAP. F Z 2.2µF/10V CHD1AZ30F225
C867 CHIP CERAMIC CAP. F Z 2.2µF/10V CHD1AZ30F225
C868 CHIP CERAMIC CAP. B K 1µF/16V CHD1CK30B105
C869 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
CONNECTORSCN101A TWG CONNECTOR 09P TWG-P09P-A1 J3TWA09TG001
CN102A TWG CONNECTOR 23P TWG-P23P-A1 J3TWA23TG001
CN103A TWG CONNECTOR 23P TWG-P23P-A1 J3TWA23TG001
CN113 PH CONNECTOR (WHITE) TOP 4P B4B-PH-K-S(LF)
J3PHC04JG017
CN411 PH CONNECTOR TOP 11P B11B-PH-K-S(LF) J3PHC11JG017
CN801 CONNECTOR BASE 008283021100000S+ J383C02UG003
Ref. No. Description Part No.
CN802 CONNECTOR BASE 008283021100000S+ J383C02UG003
DIODESD31 SWITCHING DIODE 1SS400 QD1Z001SS400
D501# SWITCHING DIODE 1SS400 QD1Z001SS400
D502 ZENER DIODE MTZJT-7724B QDTB00MTZJ24
D504# SWITCHING DIODE 1SS400 QD1Z001SS400
D505 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
D506 SWITCHING DIODE 1SS400 QD1Z001SS400
D507 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D510 SWITCHING DIODE 1SS400 QD1Z001SS400
D511 SWITCHING DIODE 1SS400 QD1Z001SS400
D512 SWITCHING DIODE 1SS400 QD1Z001SS400
D513 SWITCHING DIODE 1SS400 QD1Z001SS400
D514 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D515 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
D520 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D522 SWITCHING DIODE 1SS400 QD1Z001SS400
D523 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D525 ZENER DIODE MTZJT-7710B QDTB00MTZJ10
D526 SWITCHING DIODE 1SS400 QD1Z001SS400
D527 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D535 ZENER DIODE MTZJT-773.9B QDTB0MTZJ3R9
D605# DIODE 1N5397-B NDLZ001N5397
D606# DIODE 1N5397-B NDLZ001N5397
D607# DIODE 1N5397-B NDLZ001N5397
D608# DIODE 1N5397-B NDLZ001N5397
D609 ZENER DIODE MTZJT-775.6B QDTB0MTZJ5R6
D611# ZENER DIODE MTZJT-7722B QDTB00MTZJ22
D612 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D613 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D615 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D616# ZENER DIODE MTZJT-7733B QDTB00MTZJ33
D620 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D624# ZENER DIODE MTZJT-7733B QDTB00MTZJ33
D630# SCHOTTKY BARRIER DIODE ERC84-009 QDLZERC84009
D631# DIODE FR154 NDLZ000FR154
D633# SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D634 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D636 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D638 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D639# SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D640# DIODE FR104-B NDLZ000FR104
D641# ZENER DIODE MTZJT-7733C QDTC00MTZJ33
D642 SWITCHING DIODE 1SS400 QD1Z001SS400
D643 SWITCHING DIODE 1SS400 QD1Z001SS400
D644# SWITCHING DIODE 1SS400 QD1Z001SS400
D645# DIODE FR154 NDLZ000FR154
D646# DIODE 1ZC43(Q) QDLZ001ZC43Q
D647# ZENER DIODE MTZJT-7739B QDTB00MTZJ39
D648# SWITCHING DIODE 1SS400 QD1Z001SS400
D649# IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
D650 SWITCHING DIODE 1SS400 QD1Z001SS400
D651 SWITCHING DIODE 1SS400 QD1Z001SS400
D652 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D653 SWITCHING DIODE 1SS400 QD1Z001SS400
D655# SCHOTTKY BARRIER DIODE YG861S12RSC QDQZYG861S12
D658 PCB JUMPER D0.6-P5.0 JW5.0T
D659 PCB JUMPER D0.6-P5.0 JW5.0T
D668 SWITCHING DIODE 1SS400 QD1Z001SS400
D672 SWITCHING DIODE 1SS400 QD1Z001SS400
D681 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D682 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
Ref. No. Description Part No.
20051125 13-3 L3222EL
D701 ZENER DIODE MTZJT-778.2B QDTB0MTZJ8R2
D702 ZENER DIODE MTZJT-778.2B QDTB0MTZJ8R2
D703 ZENER DIODE MTZJT-778.2B QDTB0MTZJ8R2
D801 SWITCHING DIODE 1SS400 QD1Z001SS400
D802 SWITCHING DIODE 1SS400 QD1Z001SS400
D803 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D810 ZENER DIODE MTZJT-773.3B QDTB0MTZJ3R3
ICSIC31 IC VIF/SIF M61116FP TF0G QSZBA0SHT034
IC531# IC REGULATOR KA78R08C NSZBA0SF3119
IC533 IC NJM78L05 QSBLA0ZJR034
IC601# PHOTO COUPLER PS2501-1L QPEL0PS25011
IC671 IC VOLTAGE REGULATOR 5V KIA7805API/P NSZBA0SJY041
IC672 IC VOLTAGE REGULATOR 5V KIA7805API/P NSZBA0SJY041
IC781 IC SWITCH TC4053BF(EL N F) QSZBA0TTS163
IC801 IC AN17812A QSZBA0SMS017
IC851 IC MTS DECORDER AN5832SA-E1V QSZBA0TMS003
IC852 IC SWITCHING TC4052BF(ELNF) QSZBA0TTS162
COILSL11 INDUCTOR 22µH-K-5FT LLARKBSTU220
L12 PCB JUMPER D0.6-P5.0 JW5.0T
L21 INDUCTOR 100µH-K-5FT LLARKBSTU101
L22 INDUCTOR 150µH-J-26T LLAXJATTU151
L31 INDUCTOR 22µH-K-5FT LLARKBSTU220
L32 INDUCTOR 18µH-J-26T LLAXJATTU180
L601# LINE FILTER TLF14CB3321R0 LLBG00ZTU012
L602# LINE FILTER TLF14CB3321R0 LLBG00ZTU012
L701 INDUCTOR 22µH-K-5FT LLARKBSTU220
L781 PCB JUMPER D0.6-P5.0 JW5.0T
L851 INDUCTOR 47µH-K-5FT LLARKBSTU470
TRANSISTORSQ32 TRANSISTOR 2SA1175(F) QQSF02SA1175
Q501 TRANSISTOR 2SC2785(F) QQSF02SC2785
Q502 TRANSISTOR 2SA1576A T106R QQ1R2SA1576A
Q503 TRANSISTOR 2SC2785(F) QQSF02SC2785
Q505 TRANSISTOR KTD2059-O/P NQE0KTD2059P
Q509 TRANSISTOR 2SA1576A T106R QQ1R2SA1576A
Q510 TRANSISTOR 2SA1175(F) QQSF02SA1175
Q511 RES. BUILT-IN TRANSISTOR BA1F4M-T QQSZ00BA1F4M
Q512 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
Q513 TRANSISTOR 2SC2785(F) QQSF02SC2785
Q531 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
Q601# FET 2SK3869(Q) QFWZ2SK3869Q
Q603# TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
Q633 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q701 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q702 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q703 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q704 TRANSISTOR 2SC2785(F) QQSF02SC2785
Q705 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q706 TRANSISTOR 2SC2785(F) QQSF02SC2785
Q707 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q708 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q802 TRANSISTOR 2SC2785(F) QQSF02SC2785
Q803 TRANSISTOR 2SA1175(F) QQSF02SA1175
RESISTORSR11 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R12 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R13 INDUCTOR 0.47µH-J-26T LLAXJATTUR47
R15 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R21 CHIP RES. 1/10W J 270k Ω RRXAJR5Z0274
R23 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
Ref. No. Description Part No.
R24 CHIP RES. 1/10W J 820k Ω RRXAJR5Z0824
R34 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R36 CARBON RES. 1/4W J 12k Ω RCX4JATZ0123
R38 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R40 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153
R42 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R46 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R48 PCB JUMPER D0.6-P5.0 JW5.0T
R49 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R50 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R52 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R501 CHIP RES. 1/10W F 6.8k Ω RRXAFR5H6801
R502 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R503 CHIP RES. 1/10W F 1.6k Ω RRXAFR5H1601
R504 CARBON RES. 1/4W J 470 Ω RCX4JATZ0471
R505 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R506 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R508 MRTAL OXIDE FILM RES. 1W J 4.7k Ω RN01472KE010
R510 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R512 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R514 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R515 CARBON RES. 1/4W J 22k Ω RCX4JATZ0223
R516 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R517 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R518 CARBON RES. 1/4W J 47k Ω RCX4JATZ0473
R519 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R520 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R521 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R522 CHIP RES. 1/10W J 120k Ω RRXAJR5Z0124
R527 CHIP RES. 1/10W J 3.9k Ω RRXAJR5Z0392
R528 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R529 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R530 METAL OXIDE FILM RES. 2W J 4.7 Ω RN024R7KE010
R531 CARBON RES. 1/4W J 56k Ω RCX4JATZ0563
R532 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R533 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R534 METAL OXIDE FILM RES. RSI-1S101JHB54 RN01101KE010
R535 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R536 CARBON RES. 1/4W J 33k Ω RCX4JATZ0333
R537 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R538 PCB JUMPER D0.6-P5.0 JW5.0T
R540 PCB JUMPER D0.6-P5.0 JW5.0T
R552 FIXED METAL OXIDE FILM RE S. 1W J 1 Ω RN011R0KE010
R601# CEMENT RES. 3W K 1.2 Ω RW031R2PG007
R603 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R604 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R605 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R606 PCB JUMPER D0.6-P5.0 JW5.0T
R607 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R608 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R609 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R610 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181
R613# METAL OXIDE FILM RES. 2W J 0.47 Ω RN02R47KE010
R620 CARBON RES. 1/4W J 150 Ω RCX4JATZ0151
R621 CARBON RES. 1/4W J 820 Ω RCX4JATZ0821
R622 PCB JUMPER D0.6-P5.0 JW5.0T
R623 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R633 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R634# CARBON RES. 1/4W J 12k Ω RCX4JATZ0123
R635# CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R636 PCB JUMPER D0.6-P5.0 JW5.0T
R637# CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R638 METAL OXIDE FILM RES. 2W J 1k Ω RN02102KE010
Ref. No. Description Part No.
20051125 13-4 L3222EL
R642# CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R645 CARBON RES. 1/4W J 22k Ω RCX4JATZ0223
R646 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681
R647 CHIP RES. 1/10W F 1.8k Ω RRXAFR5H1801
R648# CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R650# CHIP RES. 1/10W F 4.7k Ω RRXAFR5H4701
R652# CHIP RES. 1/10W F 2.7k Ω RRXAFR5H2701
R653# CHIP RES. 1/10W F 2.7k Ω RRXAFR5H2701
R654# CHIP RES. 1/10W F 820 Ω RRXAFR5H8200
R655 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R656 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R657 CARBON RES. 1/4W J 390 Ω RCX4JATZ0391
R658 CARBON RES. 1/4W J 470 Ω RCX4JATZ0471
R661# CHIP RES. 1/10W F 4.3k Ω RRXAFR5H4301
R664 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R665# CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R666# CHIP RES. 1/10W F 3.6k Ω RRXAFR5H3601
R671 PCB JUMPER D0.6-P5.0 JW5.0T
R672 PCB JUMPER D0.6-P5.0 JW5.0T
R701 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391
R702 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391
R703 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R704 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R705 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R706 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R707 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R708 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R709 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R710 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391
R711 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R712 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R713 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R714 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R715 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R716 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R717 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R718 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R719 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R720 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R721 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R722 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R725 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R732 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391
R733 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R734 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R735 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R736 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R738 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R739 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R740 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391
R741 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391
R742 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R743 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R744 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R747 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R748 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R749 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R752 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R755 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R756 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R757 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R758 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R759 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
Ref. No. Description Part No.
R782 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R784 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R785 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R786 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R787 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R788 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R789 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R790 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R791 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R792 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R793 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R794 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R798 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R799 CARBON RES. 1/4W J 22k Ω RCX4JATZ0223
R801 CARBON RES. 1/2W J 100 Ω RCX2JZQZ0101
R802 CARBON RES. 1/2W J 100 Ω RCX2JZQZ0101
R803 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R804 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R805# METAL OXIDE FILM RES. 2W J 2.2 Ω RN022R2KE010
R806 CARBON RES. 1/4W J 3.3k Ω RCX4JATZ0332
R807# METAL OXIDE FILM RES. 2W J 2.2 Ω RN022R2KE010
R808 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563
R809 CHIP RES. 1/10W J 150k Ω RRXAJR5Z0154
R810 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R811 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R813 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R814 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R816 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R817 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R820 CARBON RES. 1/4W J 22k Ω RCX4JATZ0223
R821 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R822 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R823 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R824 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R825 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R826 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R827 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R829 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R830 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R831 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R832 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R833 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R834 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R835 CHIP RES. 1/10W J 5.6k Ω RRXAJR5Z0562
R836 CHIP RES. 1/10W J 330 Ω RRXAJR5Z0331
R837 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123
R838 CARBON RES. 1/4W J 12k Ω RCX4JATZ0123
R839 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123
R842 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R843 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R844 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R851 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R852 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R853 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R855 CHIP RES. 1/10W J 180k Ω RRXAJR5Z0184
MISCELLANEOUSAC601# AC CORD LP-11W&PT218P-K90A&S WAC0172LW020
B6 POW HEAT SINK PKG ASSEMBLY L3201UB 1EM420650
B7 SHIELD BOX TOP L3201UB 1EM320159
B10 HEAT SINK PKH ASSEMBLY L3201UB 1EM420648
BC401 PCB JUMPER D0.6-P5.0 JW5.0T
BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
Ref. No. Description Part No.
20051125 13-5 L3222EL
ANALOG INVERTER ASSEMBLY
INVERTER CBA
BC630 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC631 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC632 PCB JUMPER D0.6-P5.0 JW5.0T
BC634 PCB JUMPER D0.6-P5.0 JW5.0T
BC635 PCB JUMPER D0.6-P5.0 JW5.0T
BC636 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
CF31 CERAMIC FILTER SFSRA4M50CF00-B0 FBB455PMR004
F601# FUSE 51MS040L PAFC20CHV402
FH601 FUSE HOLDER MSF-015 XH01Z00LY001
FH602 FUSE HOLDER MSF-015 XH01Z00LY001
GP641# GAP. FNR-G3.10D FAZ000LD6005
JK701 Y/C JACK 1P(SW) MDC-070V1-A JYEL040LY002
JK703 RCA JACK(YELLOW) MTJ-032-06B-20 JXRL010LY050
JK704 RCA JACK(WHITE) MTJ-032-06B-22 JXRL010LY052
JK705 RCA JACK(RED) MTJ-032-06A-21 JYRL010LY014
JK706 RCA JACK(GREEN) MTJ-032-06B-25 JXRL010LY054
JK707 RCA JACK(BLUE) MTJ-032-06B-28 JXRL010LY057
JK708 RCA JACK(RED) MTJ-032-06B-21 JXRL010LY051
JK709 RCA JACK(WHITE) MTJ-032-06B-22 JXRL010LY052
JK710 RCA JACK(RED) MTJ-032-06A-21 JYRL010LY014
JK801 HEADPHONE JACK MSJ-035-10A B JYSL020LY002
JS524 PCB JUMPER D0.6-P5.0 JW5.0T
JS631 PCB JUMPER D0.6-P5.0 JW5.0T
JS634 PCB JUMPER D0.6-P5.0 JW5.0T
JS636 PCB JUMPER D0.6-P5.0 JW5.0T
JS805 PCB JUMPER D0.6-P5.0 JW5.0T
JS806 PCB JUMPER D0.6-P5.0 JW5.0T
JS813 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
L4 SCREW B-TIGHT D3X8 BIND HEAD+ GBMB3080
SA601# SURGE ABSORBER 470V+-10PER NVQZ10D471KB
SF11 SAW FILTER SAFHM45M7VAJZ01B03 FBB456PMR012
T601# SWITCHING TRANS 5723 LTT00CPKT182
TP401 PCB JUMPER D0.6-P20.0 JW20.0T
TU1 TUNER UNIT TEFH9-002A UTUNNTUAL045
Ref. No. Description Part No.
ANALOG INVERTER ASSEMBLYConsists of the following:
1ESA10861
INVERTER CBAFUNCTION CBAIR SENSOR CBA
------------------------------
Ref. No. Description Part No.
INVERTER CBAConsists of the following:
----------
CAPACITORSC401 ELECTROLYTIC CAP. 47µF/35V M CA1G470SP085
C402 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C403 ELECTROLYTIC CAP. 100µF/16V M CA1C101SP085
C404 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C405 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473
C406 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C407 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C408 CHIP CERAMIC CAP.(1608) B K 4700pF/50V CHD1JK30B472
C409 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C410 CHIP CERAMIC CAP.(1608) B K 4700pF/50V CHD1JK30B472
C412 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C413 ELECTROLYTIC CAP. 0.22µF/50V M CA1JR22SP085
C414 ELECTROLYTIC CAP. 2.2µF/50V M CA1J2R2SP085
C415 ELECTROLYTIC CAP. 2.2µF/50V M CA1J2R2SP085
Ref. No. Description Part No.
C416 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C420 ELECTROLYTIC CAP. 47µF/35V M CA1G470SP096
C422 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C423 ELECTROLYTIC CAP. 47µF/35V M CA1G470SP096
C425 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C426 ELECTROLYTIC CAP. 47µF/35V M CA1G470SP096
C428 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C429 CHIP CERAMIC CAP. B K 4.7µF/25V CHF1EK30B475
C430 CHIP CERAMIC CAP. B K 4.7µF/25V CHF1EK30B475
C431 CHIP CERAMIC CAP. B K 4.7µF/25V CHF1EK30B475
C432 CHIP CERAMIC CAP. B K 4.7µF/25V CHF1EK30B475
C433 CHIP CERAMIC CAP. B K 4.7µF/25V CHF1EK30B475
C434 CHIP CERAMIC CAP. B K 4.7µF/25V CHF1EK30B475
C440 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C441 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C442 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C450 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C451 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C452# CERAMIC CAP. SL D 10pF/3KV CCD3FDASL100
C453 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C454# CERAMIC CAP. SL D 10pF/3KV CCD3FDASL100
C455 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C460 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C462# CERAMIC CAP. SL D 10pF/3KV CCD3FDASL100
C463 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C464# CERAMIC CAP. SL D 10pF/3KV CCD3FDASL100
C465 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C490 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C492# CERAMIC CAP. SL D 10pF/3KV CCD3FDASL100
C493 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C494# CERAMIC CAP. SL D 10pF/3KV CCD3FDASL100
C495 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C496 ELECTROLYTIC CAP. 470µF/35V M CA1G471SP084
C1401 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C1403 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C1404 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C1409 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
CONNECTORSCN450 BACK LIGHT CONNECTOR 1717369-1 JB17D02AP001
CN460 BACK LIGHT CONNECTOR 1717369-1 JB17D02AP001
CN490 BACK LIGHT CONNECTOR 1717369-1 JB17D02AP001
DIODESD401 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D402 ZENER DIODE MTZJT-779.1B QDTB0MTZJ9R1
D403 ZENER DIODE MTZJT-7715B QDTB00MTZJ15
D404 ZENER DIODE MTZJT-7715B QDTB00MTZJ15
D405 ZENER DIODE MTZJT-7715B QDTB00MTZJ15
D411 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D420 ZENER DIODE MTZJT-779.1B QDTB0MTZJ9R1
D421 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D422 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D425 ZENER DIODE MTZJT-779.1B QDTB0MTZJ9R1
D426 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D427 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D430 ZENER DIODE MTZJT-779.1B QDTB0MTZJ9R1
D431 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D432 SCHOTTKY BARRIEA DIODE 11EQS04 QD4Z011EQS04
D450 SWITCHING DIODE 1SS400 QD1Z001SS400
D451 SWITCHING DIODE 1SS400 QD1Z001SS400
D452 SWITCHING DIODE 1SS400 QD1Z001SS400
D453 SWITCHING DIODE 1SS400 QD1Z001SS400
D454 SWITCHING DIODE 1SS400 QD1Z001SS400
Ref. No. Description Part No.
20051125 13-6 L3222EL
FUNCTION CBA
D455 SWITCHING DIODE 1SS400 QD1Z001SS400
D456 SWITCHING DIODE 1SS400 QD1Z001SS400
D457 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D460 SWITCHING DIODE 1SS400 QD1Z001SS400
D461 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D464 SWITCHING DIODE 1SS400 QD1Z001SS400
D465 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D466 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D467 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D472 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D473 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D490 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D491 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D492 SWITCHING DIODE 1SS400 QD1Z001SS400
D493 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D494 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D495 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D496 SWITCHING DIODE 1SS400 QD1Z001SS400
D497 SWITCHING DIODE 1SS400 QD1Z001SS400
ICSIC401 IC BD9766FV-E2 QSZBA0TRM062
IC402 IC BA10324AF-E2 QSZBA0TRM032
TRANSISTORSQ403 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
Q411# TRANSISTOR KTC3205-Y-AT/P NQSYKTC3205P
Q412 TRANSISTOR 2SC2785(F) QQSF02SC2785
Q421# FET TPC8405(TE12 L Q) QF2ZTPC8405Q
Q426# FET TPC8405(TE12 L Q) QF2ZTPC8405Q
Q433# FET TPC8405(TE12 L Q) QF2ZTPC8405Q
Q451 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q452 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q454 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q455 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q461 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q462 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q491 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
Q492 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
RESISTORSR402 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R404 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R405 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R406 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R407 METAL RESISITOR 2W J 2.2k Ω RN02222ZU001
R408 METAL RESISITOR 2W J 2.2k Ω RN02222ZU001
R409 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R411# CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R412 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R413 CHIP RES. 1/10W J 68k Ω RRXAJR5Z0683
R414 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R415 CHIP RES. 1/10W F 2k Ω RRXAFR5H2001
R416 CHIP RES. 1/10W F 30k Ω RRXAFR5H3002
R417 CHIP RES. 1/10W J 180k Ω RRXAJR5Z0184
R419 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R420 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R421 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R422 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R423 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R424 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R425 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R426 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R427 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153
R430 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
Ref. No. Description Part No.
R432 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R435 PCB JUMPER D0.6-P5.0 JW5.0T
R437 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R438 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R440 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R442 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R443 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R450 CHIP RES. 1/10W F 620 Ω RRXAFR5H6200
R451 CHIP RES.(1608) 1/10W F 15 Ω RRXAFR5H15R0
R452 CHIP RES. 1/10W F 620 Ω RRXAFR5H6200
R453 CHIP RES.(1608) 1/10W F 15 Ω RRXAFR5H15R0
R454 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
R456 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R457 CHIP RES. 1/10W J 680k Ω RRXAJR5Z0684
R458 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R459 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R460 CHIP RES. 1/10W F 620 Ω RRXAFR5H6200
R461 CHIP RES.(1608) 1/10W F 15 Ω RRXAFR5H15R0
R466 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R467 CHIP RES. 1/10W J 680k Ω RRXAJR5Z0684
R468 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R469 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R472 CHIP RES.(1608) 1/10W F 47.0 Ω RRXAFR5H47R0
R473 CHIP RES. 1/10W F 270 Ω RRXAFR5H2700
R476 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R477 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R478 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R479 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R480 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R481 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R482 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R483 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R485 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R486 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R487 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R488 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R490 CHIP RES. 1/10W F 620 Ω RRXAFR5H6200
R491 CHIP RES.(1608) 1/10W F 15 Ω RRXAFR5H15R0
R492 CHIP RES.(1608) 1/10W F 47.0 Ω RRXAFR5H47R0
R493 CHIP RES. 1/10W F 270 Ω RRXAFR5H2700
R495# CHIP RES. 1/10W J 1 Ω RRXAJR5Z01R0
R1406 CHIP RES. 1/10W F 2k Ω RRXAFR5H2001
MISCELLANEOUSCLN411 11P WIRE ASSEMBLY WX1L3200-003 WX1L3200-003
RL401 POWER RELAY SDT-S-112LMR MRNDC12QN014
T450# INVERTER TRANS ETJV25ZB12AC LTZ00CPMS004
T460# INVERTER TRANS ETJV25ZB12AC LTZ00CPMS004
T490# INVERTER TRANS ETJV25ZB12AC LTZ00CPMS004
Ref. No. Description Part No.
FUNCTION CBAConsists of the following:
----------
CAPACITORC61 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
RESISTORSR61 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R62 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R63 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152
R64 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152
R65 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R66 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
Ref. No. Description Part No.
20051125 13-7 L3222EL
IR SENSOR CBA
R67 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R68 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R69 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R70 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
SWITCHESSW61 TACT SWITCH SKQSAB SST0101AL038
SW62 TACT SWITCH SKQSAB SST0101AL038
SW63 TACT SWITCH SKQSAB SST0101AL038
SW64 TACT SWITCH SKQSAB SST0101AL038
SW65 TACT SWITCH SKQSAB SST0101AL038
SW67 TACT SWITCH SKQSAB SST0101AL038
SW71 TACT SWITCH SKQSAB SST0101AL038
MISCELLANEOUSCLN104 5P-8P WIRE ASSEMBLY 5P-8P WIRE
ASSEMBLYWX1L3201-006
JS62 PCB JUMPER D0.6-P5.0 JW5.0T
JS63 PCB JUMPER D0.6-P5.0 JW5.0T
Ref. No. Description Part No.
IR SENSOR CBAConsists of the following:
----------
CAPACITORC91 ELECTROLYTIC CAP. 47µF/10V M H7 CE1AMASSL470
DIODED91 LED L-53HT NP4Z000L53HT
TRANSISTORQ91 TRANSISTOR 2SC4081 T106 Q QQ1Q02SC4081
RESISTORSR91 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R92 CHIP RES. 1/10W J 68 Ω RRXAJR5Z0680
R93 CARBON RES. 1/4W J 68 Ω RCX4JATZ0680
R94 CARBON RES. 1/4W J 150 Ω RCX4JATZ0151
R95 CHIP RES. 1/10W J 150 Ω RRXAJR5Z0151
R96 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
MISCELLANEOUSCLN105 5P WIRE ASSEMBLY 5P WIRE ASSEMBLY WX1L3201-004
JS91 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
JS93 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
JS94 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
RCV91 PHOTO LINK MODULE KSM-712TH2E USESJRSKK044
Ref. No. Description Part No.
EWL20S5L3222UC
2005-12-06
top related