engineered with thin plate pure lead (tppl) … · pure lead plates to provide more power, the...
Post on 26-Feb-2019
213 Views
Preview:
TRANSCRIPT
© 2014 EnerSys. All rights reserved. Trademarks and logos are the property of EnerSys and its affiliates, except Gyrocopter™, which is not the property of EnerSys.
EXTREME POWER AND ENDURANCE
E N G I N E E R E D W I T H T H I N P L AT E P U R E L E A D ( T P P L ) T E C H N O L O G Y
SERIESTM
www.odysseybattery.com www.enersys.com
DRIVE IT TO EXTREMESUp to twice the overall power of conventional batteries!
Doing double dutySome batteries offer enormous cranking power. Others, deep cycle reserve power. Unbeatable ODYSSEY® Extreme SeriesTM batteries do both.
Even at very low temperatures, ODYSSEY Extreme Series batteries have the power to provide engine-cranking pulses in excess of 2250 amps for 5 seconds – double to triple that of equally sized conventional batteries. And they can handle 400 charge-discharge cycles to 80% depth of discharge.†
How so much power is possibleODYSSEY Extreme Series batteries are made with flat plates made of 99.99% pure lead – not lead alloy. Pure lead plates can be made thinner, so we can fit more of them in the battery. More ODYSSEY battery plates mean more plate surface area. And that means more power – twice as much as conventional batteries.
Packed with more powerLike many popular spiral-wound batteries, ODYSSEY Extreme Series batteries employ dry cell Absorbed Glass Mat (AGM) technology to contain acid, allowing the battery to be installed even on its side. But the densely packed flat plates in an ODYSSEY Extreme Series battery avoid the “dead space” between cylinders in a “six pack” design. The result is 15% more plate surface area - and that translates to more power!
While we have evolved the name to ODYSSEY® Extreme SeriesTM batteries, and we’ve updated the look, rest assured that the Extreme Series batteries are packed with the same power and technology you’ve been depending on for years.
Shipped fully charged. Get it and go!
ODYSSEY Extreme Series batteries are ready for use right out of the box. If the ODYSSEY Extreme Series battery’s voltage is 12.65V or greater, simply install the battery in your vehicle and you are ready to go! If below 12.65V, boost charge following the instructions in the ODYSSEY Extreme Series battery Owner’s Manual and/or Technical Manual. Putting a boost on the battery will not damage it, even if its voltage reads higher than 12.65V.
†PC370, PC950 and PC1100 are engine start only. Limited cycling.
Unused battery space
ODYSSEY ® batteries have a new name and new look!
www.odysseybattery.com www.enersys.com
SERIESTM
ODYSSEY® Extreme Series™ batteries vs. spiral-wound designs: 15% more plate surface area!
Pure Lead PlatesTo provide more power, the plates in our batteries are constructed from 99.99% pure lead. The plates are extremely thin, so more of them can fit into the battery. More lead plates means more power.
Compressed TPPL Plate Separators For extreme vibration resistance, the TPPL plate separators are compressed before being inserted into the case.
Tin Alloy Coated Brass Terminals* To ensure secure, corrosion-free cable connections, our brass terminals are coated with a high-quality tin alloy◆
RUN STRONGER LONGERDesigned and built to last up to 3 times as long as conventional batteries!
*Excludes PC1220 and PC1350
**At 25°C. Storage times will be even longer at lower temperatures.
◆Some models excluded. See table for details.
Robust Intercell Connections To resist vibration and eliminate internal sparking, cell connectors are casted to the plates and bonded.
Boasting rugged construction and TPPL design, ODYSSEY® Extreme SeriesTM batteries have an 8-12 year design life and a 3-10 year service life.
• Select ODYSSEY Extreme Series batteries are available with metal casing for high heat applications.
• TPPL design holds acid in place to prevent spills, even when installed on its side.
• ODYSSEY Extreme Series batteries can be stored for up to 2 years and still be returned to full power.**
SUPERIOR STARTING POWER AND VIBRATION RESISTANCE
The ODYSSEY® Extreme SeriesTM battery’s incredible combination of power and endurance makes these batteries ideal for just about anything, just about anywhere.
Emergency ResponseODYSSEY® Extreme SeriesTM batteries are always on call with maintenance-free starting power plus massive deep cycle reserve power for on-board accessories.
• Police cars• Fire engines • Ambulances
4X4 & Off-RoadRugged construction and non-spillable, dry cell design ensure extreme shock and vibration resistance for the toughest off-road applications.
• SUVs• Light trucks• Off-road vehicles
Heavy Duty/CommercialSuperior cranking power and deep cycle ability mean ODYSSEY Extreme Series batteries get the job done.
• Farm, lawn and garden equipment• Tractor trailers • Earth-moving/
construction equipment
Motorcycles & PowersportsThe ODYSSEY Extreme Series battery delivers the power and durability that powersports vehicles demand. Rugged construction and non-spillable, dry cell design provides extreme shock and vibration resistance.
• Motorcycles and ATVs• Personal watercraft • Snowmobiles• Ultralight and GyrocopterTM aircraft
High Performance & Modified VehiclesFrom starting high-compression engines to powering high-intensity discharge lights, ODYSSEY Extreme Series batteries can handle any upgrade, and can be mounted in almost any position.
• Tuner cars • Race cars• Dragsters
Sound and Video PackagesODYSSEY Extreme Series batteries provide the power and mounting flexibility that today’s high-wattage, in-car sound and video systems demand.
• Audio systems• Video systems• Auxiliary amplifiers
Classic & Vintage CarsThe deep cycle reserve power of ODYSSEY® Extreme SeriesTM batteries ensures that classic and vintage cars will start reliably, even after two years of sitting idle.
• Vintage vehicles• Classic trucks• Muscle cars
ODYSSEY® EXTREME SERIESTM BATTERY POWER FOR EVERY APPLICATION.
* Cold Start Performance: S.A.E J537 JUNE 82 **Pulse Current † Can be fitted with brass automotive terminal
Optional metal jackets: available on PC545, PC680, PC925, PC1200, PC1700 and 31-PC2150
Operating Temperature Range: PC310, PC370, PC950, PC1100 and PC1800-FT: -40°C to 50°C, PC535 and PC625: -40°C to 45°C, PC545, PC680, PC925, PC1200 and PC1700 without metal jacket: -40°C to 45°C, PC545, PC680, PC925, PC1200 and PC1700 with metal jacket: -40°C to 80°C, PC1220, PC1350 and PC2250: -40°C to 40°C, All other models: -40ºC to 80ºC
†† Height may include SAE/DIN terminal, metal jacket and maximum tolerance
Model Voltage PHCA** (5 sec) CCA* HCA MCA
Nominal Capacity Reserve Capacity Minutes
Length mm
Width mm
Height†† mm
Weight kg Terminal
Torque Specs
Nm max
Internal Resistance
(mΩ)
Short Circuit Current20 Hr
Rate-Ah10 Hr
Rate-Ah
PC310 12 310 100 200 155 8 7 9 137.5 86.0 99.0 2.7 M4 Receptacle 1.0 27.1 455A
PC370 12 425 200 315 270 15 14 25 200.0 77.0 140.0 5.7 M6 Stud 3.9 13.5 891A
PC535 12 535 200 300 265 14 13 21 170.2 99.1 158.5 5.4 M6 Receptacle 4.5 8 1000A
PC545 12 460 150 280 220 13 12 18 177.8 85.9 131.3 5.2 M6 Receptacle 5.6 10 1200A
PC625 12 530 200 420 340 18 17 27 170.2 99.1 176.5 6.0 M6 Receptacle 4.5 7 1800A
PC680 12 520 170 350 280 16 16 24 184.7 79.0 191.8 7.0M6 Receptacle†
or SAE 3/8” Receptacle
5.6 7 1800A
PC925 12 900 330 610 480 28 27 48 168.7 179.1 148.1 11.8M6 Receptacle†
or SAE 3/8” Receptacle
6.8 5 2400A
PC950 12 950 400 600 500 34 32 60 250.0 97.0 156.0 9.0 M6 Stud 3.9 7.1 1700A
PC1100 12 1100 500 800 650 45 43 87 250.0 97.0 206.0 12.5 M6 Stud 3.9 5.1 2450A
PC1200 12 1200 540 860 725 42 40 78 199.9 169.2 193.0 17.4M6 Receptacle†
or SAE 3/8” Receptacle
6.8 4.5 2600A
PC1220 12 1220 680 960 860 70 64.8 135 278.0 175.0 190.0 20.7 DIN Lead Post N/A 5.7 2200A
75/86-PC1230 12 1230 760 1050 815 55 50 110 240.3 179.8 201.2 20.6 TOP SAE SIDE 3/8” Receptacle 6.8 2.5 3100A
PC1350 12 1350 770 1080 960 95 88.5 195 353.0 175.0 190.0 27.4 DIN Lead Post N/A 4.2 2900A
25-PC1400 12 1400 850 1150 950 65 55 130 240.3 173.7 220.7 22.7 SAE 6.8 2.5 3100A
35-PC1400 12 1400 850 1150 950 65 55 130 240.3 173.7 220.7 22.7 SAE 6.8 2.5 3100A
34-PC1500 12 1500 850 1250 1050 68 62 135 275.6 171.7 200.2 22.4 SAE 6.8 2.5 3100A
34R-PC1500 12 1500 850 1250 1050 68 62 135 275.6 171.7 200.2 22.4 SAE 6.8 2.5 3100A
34M-PC1500 12 1500 850 1250 1050 68 62 135 275.6 171.7 201.9 22.4SAE and
3/8” Stud (Pos.), 5/16” Stud (Neg.)
6.8 2.5 3100A
34/78-PC1500 12 1500 850 1250 1050 68 62 135 275.6 179.8 200.2 22.4 TOP SAE SIDE 3/8” Receptacle 6.8 2.5 3100A
PC1700 12 1550 810 1325 1175 68 65 142 331.0 168.4 197.6 27.6M6 Receptacle†
or SAE 3/8” Receptacle
6.8 3.5 3500A
65-PC1750 12 1750 950 1350 1070 74 65 145 300.5 182.9 190.5 26.3 SAE 6.8 2.0 5000A
PC1800-FT 12 1800 1300 1600 1450 214 190 475 581.0 125.0 316.5 60.0 M10 Stud 9.0 3.3 3800A
31-PC2150 12 2150 1150 1545 1370 100 92 205 331.7 175.0 243.6 35.3 3/8” Stud or SAE† 16.9-22.6 2.2 5000A
31M-PC2150 12 2150 1150 1545 1370 100 92 205 330.2 172.7 238.5 35.3SAE and
3/8” Stud (Pos.), 5/16” Stud (Neg.)
16.9-22.6 2.2 5000A
PC2250 12 2250 1225 1730 1550 126 114 240 286.0 269.0 233.0 39.0 DIN Terminal and 3/8” Stud
11.0 For 3/8”
Stud Only2.1 5000A
ODYSSEY® EXTREME SERIESTM BATTERY POWER FOR EVERY APPLICATION.
ODYSSEY® EXTREME SERIESTM BATTERY TECHNOLOGY COMPARISON
ODYSSEY®
EXTREME SERIESTM
BATTERIES
CONVENTIONALBATTERIES
DESIGN LIFE 8-12 years (Float) @ 25˚C
5 years
SERVICE LIFE 3 to 10 years 1 to 5 years
ELECTROLYTE Drycell (“starved electrolyte”) no external leakage or corrosion
Most are acid flooded (causing acid burns and spills); some wet sealed or “gelled”
STORAGE LIFE 2 years before needing charge @ 25˚C
6-12 weeks before needing charge
SHIPPING Air transportable; US Department of Transportation classified non-spillable (less expensive)
Ground transport; classified as hazardous material (more expensive)
END OF LIFE Battery slowly loses power at end of life; no catastrophic failure
Immediate and catastrophic loss of power (can leave you stranded)
WARRANTY
EnerSys Energy Products Inc. warrants its ODYSSEY® Extreme Series™ batteries to be free of defects in material and workmanship. In the event of your battery failing, we advise first determining if the battery requires a boost charge or if it needs replacing. Often a battery that is deemed to have failed is simply discharged and just requires a boost charge.
Please see our Warranty Policy, which is available from the Downloads area of our website: www.enersys-emea.com.
TERMINAL LAYOUTS
34/78-PC1500
34-PC1500 34R-PC1500
PC1700 65-PC1750
+ -
PC535
PC680 PC925***
PC545 PC625
75/86-PC1230
PC1200***
25-PC1400 35-PC1400
34M-PC1500 PC1800-FT PC225031-PC2150 31M-PC2150
PC1350
PC1220
PC310 PC370
PC950 PC1100
Drawing sizes are for terminal position reference only; diagrams are not proportionate to each other. ***Optional Reversed Polarity (L)
PC310 PC370
PC680 PC925***
PC535 PC545 PC625
PC950 PC1100 PC1200*** PC1220
75/86-PC1230 PC1350 25-PC1400 35-PC1400 34-PC1500 34R-PC1500
34M-PC1500 34/78PC1500 PC1800-FT 31-PC2150 31M-PC2150 PC2250
PC1700 65-PC1750
About EnerSys®
EnerSys® is a global leader in stored energy solutions for automotive, military, and industrial applications. With manufacturing facilities in 18 countries, sales and service locations throughout the world, and over 100 years of battery experience, EnerSys is a powerful partner for automotive service and parts providers.
EnerSys Global Headquarters2366 Bernville RoadReading, PA 19605Tel: +1-610-208-1991 +1-800-538-3627Fax:+1-610-372-8613
EnerSys EMEA EH Europe GmbHLöwenstrasse 328001 Zürich, SwitzerlandTel: +41 (0) 44 215 74 10
EnerSys Asia152 Beach RoadGateway East Building #11-03Singapore 189721Tel: +65 6508 1780
www.odysseybattery.comwww.enersys.com
© 2014 EnerSys. All rights reserved. Trademarks and logos are the property of EnerSys and its affiliates, except Gyrocopter™, which is not the property of EnerSys.
Publication No: EN-ODY-RS-010 – June 2014. Subject to revisions without prior notice. E.&O.E.
top related