foundation - allduro.comallduro.com/.../10/colphene-bsw-uni-ng-brochure.pdf · foundation high...
Post on 12-Aug-2020
2 Views
Preview:
TRANSCRIPT
F O U N D AT I O N
F O U N D AT I O N
HIGH PERFORMANCE PRE-APPLIED AND POST-APPLIED SYSTEMS FOR BLIND SIDE & BELOW GRADE WATERPROOFING APPLICATIONS
COLPHENE BSW is a fully reinforced Pre-Applied system membrane designed for horizontal and vertical external blind-side waterproofing applications. The system is composed of a select blend of high performance SBS modified bitumen combined with an ultra high strength reinforcement and a specially formulated top surface.
P R E - A P P L I E D WAT E R P R O O F I N G
COLPHENE BSW
COLPHENE 3000 is a high quality, self-adhesive waterproofing membrane ideal for waterproofing foundations, below-grade walls, plaza decks, and other concrete substrates. The membrane is composed of SBS modified bitumen and a tri-laminated woven polyethylene with multiple advantages.
P O S T- A P P L I E D WAT E R P R O O F I N G
COLPHENE 3000
SOPREM
A - Foundation
3
P R E - A P P L I E D B E L O W G R A D E WAT E R P R O O F I N G
COLPHENE BSW - system components
P R O D U C T N A M E D E S C R I P T I O N D I M E N S I O N SI N S TA L L AT I O N
M E T H O DT H I C K N E S S
COLPHENE BSW V(Vertical)
Colphene BSW is applied directly to the prepared substrate or form workbefore structural concrete is poured.
TOP FACE is coated with specially treated silica sand.
UNDERFACE is self-adhesive protected with a silicone release film.
1 x 10m Self-adhesive 3mm
BSW UNI NG(Horizontal & Vertical)
TOP FACE is coated with specially treated silica sand.
UNDERFACE is protected by polypropylene film.
1 x 8m Loose laid 4mm
COMPLEMENTARY PRODUCT
ALSAN FLASHING WITH FLEECE ALSAN Flashing is a proprietary polyurethane bituminous resin specifically formulated for high performance liquid-applied flashings, other details and maintenance applications.
SOPRADRAIN 10-G / 15-G SOPRADRAIN 10-G / 15-G is a high density drainage board composed of a polypropylene core on which a geotextile is factory laminated. The board is installed for the drainage of vertical below grade walls.
4
SOPR
EMA
- Fo
unda
tion
The system is to provide a full and continuous bond of the membrane to the poured structural concrete to waterproof and protect the sub-structure envelope from the blindside. This will eliminate the potential of water penetration and leakage.
• Time & cost saving on project schedule & budget;
• Eliminates the need for concrete screed on the horizontal;
• Eliminates the need for protection board on the vertical;
• Allows for optional design considerations for the use of water stop;
• Excellent protection against water infiltration at critical locations;
• Superior mechanical properties;
• Resistant to chemicals (Chloride, Sulphate and Ph level between 2 and 10).
• Outstanding adhesion to structural poured concrete;
• Homogeneous, fully sealed systems on overlaps;
• Non-Permeable to vapor and gas;
• Fast & easy installation;
• No tapes are required.
ADVANTAGES
CONCEPT
COLPHENE BSW (Pre-Applied Waterproofing System Fully Bonded to Structural Concrete)
As it is normal behaviour of concrete to crack it is always necessary to protect it from water infiltration.
The technology and concept of COLPHENE BSW ensure watertight substructure envelope.
FULLY BONDED TO STRUCTURAL CONCRETE
Waterproofing System(When not Bonded to the Structural Concrete Slab)
When water migration between membrane and structural concrete in blindside waterproofing is present, the structure becomes vulnerable and the liability of the design and construction team is huge and the remedy is expensive.
LOOSE LAID
FULLY BONDED TO THE BLINDING
P R E - A P P L I E D WAT E R P R O O F I N G
5
SOPREM
A - Foundation
The COLPHENE BSW system with its superior adhesion to poured concrete, high resistance to hydrostatic pressure and excellent resistance to tear and puncture is the optimum solution for the design and construction team to keep the water on the outside and ensure a dry, leak free substructure envelope.
VALUE
The COLPHENE BSW system membrane composition is designed with an engineered technology utilizing the exothermic synergy to create a superior mechanical bond-strength of the membrane to the structural poured concrete, introducing a unique, unsurpassed Pre-Applied / Blind-Side waterproofing system to the construction industry featuring:
• MORE WATERPROOFING CAPABILITIES ENHANCED REINFORCEMENT
The ultra-high strength reinforcement is fully encapsulated in bitumen on both sides providing excellent dimensional stability.
• CONTINUOUS BOND
Continuous and homogenous bond to structural concrete.
• LAP-ADHESION
Unsurpassed lap adhesion.
• PEEL STRENGTH
Excellent adhesion to the structural poured concrete surface with.
• PUNCTURE RESISTANCE
Very high puncture resistance.
TECHNOLOGY
The top face of the membrane is SBS modified bitumen covered with sand. The specially formulated surface softens slightly as the concrete starts to cure, releasing heat. This promotes adherence of the membrane to the concrete, and prevents the ingress or migration of water around the structure.
RESISTANCE TO HYDROSTATIC HEADCOLPHENE BSW can be used in application where high hydrostatic pressure is present. Membranes have been designed to withstand up to 114 m, where other conventional waterproofing become vulnerable.
COLPHENE BSW have been proven to resist water migration in such conditions.
UV stabilized 60 days exposure to UV will not affect performance of waterproofing system.
High mechanical properties to withstand traffic, puncture and exterior elements.
DURABILITY
Penetrations through slabs and walls represent a high risk area for water penetration and leakage. At these points, it is crucial to ensure an effective continuous seal between the membrane and the penetration. ALSAN FLASHING single component, polyurethane, bitumen liquid is a UV resistant waterproofing membrane recommended for this application. This is an essential component of the system to ensure complete, continous seal of substructure envelope.
PENETRATION DETAILING
P R E - A P P L I E D WAT E R P R O O F I N G
6
SOPR
EMA
- Fo
unda
tion
P R E - A P P L I E D WAT E R P R O O F I N G
COLPHENE BSW SYSTEM
VERTICAL APPLICATIONSIn vertical applications concrete can be cast directly onto the COLPHENE BSW V, no protection board is required.
HORIZONTAL APPLICATIONSIn horizontal applications, concrete can be cast directly onto the BSW UNI NG.
Slab on Grade
COLPHENE BSW V
Prepared substrate
Earth
Concrete blinding
ALSAN FLASHINGPile Cap Head
Liquid Waterproofing Membrane
FLASHING reinforcement
ALSAN FLASHING
BSW UNI NG
BSW UNI NG
SOPREM
A - Foundation
7
8
SOPR
EMA
- Fo
unda
tion
SOPREM
A - Foundation
9
P O S T- A P P L I E D WAT E R P R O O F I N G
COLPHENE 3000
COLPHENE 3000 is a self-adhesive waterproofing membrane composed of SBS modified bitumen and a tri-laminated woven polyethylene facer. The self-adhesive
underface is protected by a silicone release film. The COLPHENE 3000 membrane is used to ensure the waterproofing of foundation walls and other below grade vertical walls.
SOPREM
A - Foundation
11
P O S T- A P P L I E D WAT E R P R O O F I N G
COLPHENE 3000
P R O D U C T N A M E D E S C R I P T I O N D I M E N S I O N S I N S TA L L AT I O N M E T H O D T H I C K N E S S
COLPHENE 3000
TOP FACE Tri-laminated woven polyethylene.
UNDERFACE Silicon release film.
18.7 × 1(61 × 3.3) Self-adhesive 1.5mm
COMPLEMENTARY PRODUCT
ELASTOCOL STICK ELASTOCOL STICK is a primer designed to enhance the adhesion of self-adhesive membranes on porous surfaces. It is composed of SBS synthetic rubbers, adhesion-enhancing resins and volatile solvents. It is used as a primer on surfaces such as concrete, metal, and wood.
SOPRAMASTIC ALU SOPRAMASTIC ALU is an aluminum-coloured mastic composed of SBS modified, fibres and solvents. It is used as a complement to bituminous waterproofing membranes as joint filler and caulking material. It is compatible with bitumen-based materials and has excellent waterproofing properties.SOPRAMASTIC ALU contains a leafing aluminum pigmentation which provides superior protection against ultraviolet rays throughout the service life of the product. It is formulated with a high content of polymers, which gives it superior resistance to flow at high temperature.
12
SOPR
EMA
- Fo
unda
tion
P O S T- A P P L I E D WAT E R P R O O F I N G
COLPHENE 3000
• High tensile strength and puncture resistance
• Greater flexibility
• Constant thickness
ADVANTAGES
SOPREM
A - Foundation
13
Here is a completed waterproofing project.
Use SOPRAMASTIC to seal details and critical areas.The use of a protection or drainage board is recommended before backfilling to ensure the integrity of the waterproofing membrane.
Peel back the top part of the silicone release film. Adhere COLPHENE 3000 to the substrate, making sure the membrane is well aligned.
Prime the substrate with ELASTOCOL STICK, ELASTOCOL STICK ZERO or ELASTOCOL STICK H2O.
Gradually peel back the remaining silicone release film, making sure the membrane is completely adhered.The use of a hand roller is required to remove air pockets.
1 2
3 4
5
P O S T- A P P L I E D WAT E R P R O O F I N G
COLPHENE 3000
INSTALLATION INSTRUCTIONS
14
SOPR
EMA
- Fo
unda
tion
SOPREM
A - Foundation
15
S I N G A P O R E+65 6818 6353
Level 39 Marina Bay Financial Centre Tower 2,10 Marina BoulevardSingapore018983
Fax: +65 6818 6111info@soprema.com.sg
H O N G K O N G
+852 3552 2848
Level 12, 1 Peking Road, Tsim Sha Tsui,Kowloon Hong KongSARChina
Fax: +852 3980 9333info@soprema.hk
C H I N A +86 21 6252 1882
Unit E, 9F, Block 4, Kingboard Enterprise SquareNo.269 Tongxie Road,Changning DistrictShanghaiChina 200335
Fax: 86 21 6252 1992info@soprema.cn
A U S T R A L I A+61 2 8051 3153
Level 36, Gateway, 1 Macquarie PlaceSydneyNSW 2000Australia
info@soprema.com.au
V I E T N A M+84 8 3520 2944
Unit 721-3, Level 7,
Me Linh Point Tower,
2 Ngo Duc Ke Street,
District 1, Ho Chi Minh City,
Vietnam
info@soprema.com.vn
top related