keywords : frp, gfrp, frame, pushover, frp joint, frp bolt
Post on 03-Jan-2016
96 Views
Preview:
DESCRIPTION
TRANSCRIPT
FC1
F : Frame
C : Chemical
1 : One Span
FC1T
F : Frame
C : Chemical
1 : One Span
T : Tension
FC1C
F : Frame
C : Chemical
1 : One Span
C : Compression
FB1
F : Frame
B : Bolt
1 : One Span
FB1T
F : Frame
B : Bolt
1 : SOne Span
T : Tension
FB1C
F : Frame
B : Bolt
1 : One Span
C : Compression
A Study on Pushover Test and Numerical Analysisof GFRP Frame with FRP Joints
Yeou-Fong Li1 and Bo-Shiang Wang2
Keywords : FRP, GFRP, Frame, Pushover, FRP Joint, FRP Bolt
Abstract :This study uses Glass Fiber Reinforced Plastic (GFRP) composites to produce a framework the behavior of which was analyzed in a pushover experiment and by using a numerical analysis software. In the specimental plan, double-web FRP I-beams are used for the beams and columns of the frame but the joint are made from an GFRP deck cut into the desired form, bonded together and wrapped with carbon fiber sheet. Three types of frame specimens with braces in compression, tension and no bracing were used for each joint type – chemically bonded joint or a hybrid joint using GFRP bolts in addition to epoxy resin. When making the specimens the double-web I-beam is given a 45 ° cut at the ends to let joint fit in the frame. The joint is then bonded to the frame by chemical bonding or by hybrid bonding. The experimental results showed that the mechanical behavior of the hybrid joint is better than the chemically bonded joint and that tension bracing has a better performance. This study also uses numerical analysis software SAP2000 for the pushover simulation analysis of the frames and it was learned that the ultimate stength and force-displacement curce of the analytical results were similar to that of the experimental ones.
1Professor of the Department of Civil Engineering , NTUT, Taipei, Taiwan .
2 Master of the Department of Civil Engineering, NTUT, Taipei, Taiwan.
Experiment Plan
Experiment Result
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
F C 1F C 1 TF C 1 C
SpecimensPmax (kN)
K (kN/cm)
Energy Dissipation
Specimens Cost (NTD)
FC1 14.2 12.9 42.62 5811
FC1T 22.3 51.6 73.72 6304
FC1C 19.38 44.3 50.58 6304
FB1 17.75 17.8 42.62 5845
FB1T 30.24 59.7 73.72 6344
FB1C 24.7 50.7 50.58 6344
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
F B 1F B 1 TF B 1 C
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
E x p e r im e n tA n a ly sis
Numerical Analysis Result
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
E x p e r im e n tA n a ly sis
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
E x p e r im e n tA n a ly sis
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
E x p e r im e n tA n a ly sis
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
E x p e r im e n tA n a ly sis
0 2 4 6 8 1 0D isp la cem en t (cm )
0
1 0
2 0
3 0
For
ce (
kN)
0 2 4 6 81 3 5 7D rift R a tio (% )
E x p e r im e n tA n a ly sis
FC1 FC1T FC1C
FB1CFB1TFB1
側向支撐千斤頂
Load Cell
Dial Gauge40 cm
LVDT
反力剛架
122.5 cm
鋼床板
SpecimensExperiment Pmax
(kN)Analysys Pmax
(kN)Error (%)
FC1 14.2 14.18 0.1
FC1T 22.3 22.4 0.4
FC1C 19.38 19.45 0.35
FB1 11.68 12.55 0.7
FB1T 30.24 30.4 0.5
FB1C 24.7 24.9 0.8
0 1 2 3 4 5 6
D rift R a tio (% )
0
5 0
1 0 0
1 5 0
2 0 0
En
ergy
dis
sip
atio
n
F C 1F C 1 TF C 1 C
0 1 2 3 4 5 6
D rift R a tio (% )
0
5 0
1 0 0
1 5 0
2 0 0
En
ergy
dis
sip
atio
n
F B 1F B 1 TF B 1 C
top related