kunal ppt jumbo drill

JUMBO DRILL

TRAINING AT UCIL,TURAMDIH

PRESENTED BY:KUNAL KUMAR SINGH

ISM DHANBADM.TECH (MME)

INTRODUCTION

AXERA D05 126-126XL is intended for use in mining, preparation work and tunnelling. It is an independently operating hydraulic rig that drills vertical, inclined and horizontal holes. Jumbo drills are used in mining, for making drills in all direction.The tamrock Axera D05-126 is a single boom electro-hydraulic jumbo for mining development in cross section up to 38 m2.

The robust universal boom have a large optimum shaped coverage, 360˚ rotation and full automatic parallelism for fast and easy face drilling. The boom can also be used for cross-cutting and bolt-hole drilling.The jumbo layout is designed for good visibility and balance, this and the powerful four-wheel-drive articulated carrier ensure fast and safe manoeuvering in narrow drifts.The high performance drilling system allows high drilling performance with good drill steel economy and high machine reliability.The operator environment and added automatic functions allow the operator to concentrate on safe, fast and accurate drilling.All the service points are well protected but easy to access.

MAIN SPECIFICATIONS: -

Carrier 1*CB05Rock drill 1*HL 510 S-38Boom 1*B 26 FFeed 1*TF 500Length 11.42 mWidth 1.75 mHeight roof down 2.10 m

roof up 3.02 mTurning radius 5.22 / 2.98 mTramming speed horizontal 12 Km / h

13%=1:7=8° 5 Km / hGradeability, maximum 35 %Noise level < 98 dB (A)Weight 11 Tonne

Components of the machine

1. ROCK DRILL2. FEED3. BOOM4. FRONT

STABILIZERS

BOOM

1. BOOM SWING2. BOOM

EXTENSION3. DIVERGENCE4. FEED

EXTENSION5. FEED SWING

(MAIN)6. BOOM LIFT7. FEED SWING

(SLAVE)8. FEED TILT9. FEED ROLL-

OVER

DESCRIPTION:

The X-Y coordinated boom movements together with 360° actuator roll-over make the use of the boom simple and logical. Accurate automatic parallel holding both in vertical and horizontal plane improves the drilling performance and accuracy.

Large dimensioned rectangular profile, adjustable and sealed boom extension wear-pieces, large diameter bearings, sealed main joints, expanding pins in cylinder joints and use of super strong cast pieces in most stressed areas are some of the features that are included to the boom design for improve reliability.

KEY FEATURES:

INNOVATIVE DESIGNCOMPACT AND POWERFULLEASY TO HANDLETRAMMING PERFORMANCESLARGE BOOM COVERAGETHC DRILLING SYSTEMOPERATOR’S FRIENDLY ENVIRONMENTEASY MAINTENANCE

1550

6250

1350 1400 2550

1980

2100

920

11180 with CC 2512 Feed

1750

250 320

JUMBO DRILL ( AXERA D05) MANUFACTURED BY: SANDVIK

POWERFULL

45 kW electro-hydraulic power pack IP 55 protection class

1000 V system available

80 m capacity electric cable reel

R1 R2

EASY TO HANDLE:

Increased Steering Angle

Increased Stability

Narrower Articulated Jumbo

Design

Transfer of the mass outside

the curve

Corneringin 2.9 x 2.9 mwide tunnels.

LARGE BOOM COVERAGE

B 26 F BOOMAccurate parallel holdingRobust boom supportX-Y coordinated boom controlsAll proportional movementsLarge capacity hydraulic systemBox profile with large dimensions1.2 m boom extension

LARGE BOOM COVERAGE

B 26 XL F BOOM

Accurate parallel holdingRobust boom supportX-Y coordinated boom controlsAll proportional movementsLarge capacity hydraulic systemBox profile with large dimensions1.7 m boom extension

THC DRILLING SYSTEM

POWERFULL AND RELIABLE HYDRAULICS

45 Kw Power Pack•1 variable displacement pump for percussion, feed and boom.•1 gear pump for rotation.

OPERATOR’S FRIENDLY ENVIRONMENT:

Optimized design of controls.

Steering wheel and pedalsfor tramming up to 12 kph.

Roomy operator ’s station.

Tramming and drilling from a comfortable seated position.

EASY MAINTENANCE

Carrier•Easy access to all service points.Rock Drill•Modules can be changed andserviced on feed beam.•Visual wear indicatorsTHC•Simple and quick diagnostics.Boom•Wearing pieces can be changed without dismantling the boom.•Clearance can be adjusted by conical cylinder pins.

•Haulage: diesel•Drilling: electrically

Hose pipe: •Percussion• Lubrication: (air + oil) mixtureOIL (Servonium 100)•Rotation• Water hose: Connected to drill rod.• Tank return: extra oil return to the main oil storage tank.

DRILLING

PERCUSSION

ROTATION

PERCUSSION

PRESSURE LINE

RETURN LINE

ROTATION

PRESSURE LINE

RETURN LINE

Single Boom: Hydraulically operated for its 3600 rotation.

Main Boom: Boom extension

Feed Boom: To feed forward or backward

Roll Over Cylinder: To rotate the feed boom

Feed Tilt: Cylinder-piston

Boom Swing: Cylinder-piston ( )

Boom Lift: Cylinder-piston ( )

Jack Cylinder: Reduce load over wheel while drilling and provide stability with flexibility

Electric motor: Main motor requires power supply 440 V.

Pump (hydraulic tank) for suction and send to various different parts.

Compressor: air + oil (receiver cylinder)

Water pump

Canopy: over driver seat (driver seat rotatory).

ENGINE

4 CYLINDER IN LINEAIR COOLED

GENERAL DIMENSIONS

ROCK DRILL

Model HL 510 S-38Standard male shank R 38Weight 130 kgImpact frequency 59 HzPercussion pressure 175 barImpact power 16 kW

BOOM

Model B 26 FType Parallel holdingWeight (with hoses) 1 900 kgFeed roll-over 360°Boom extension 1 200 mmFeed extension 1 600 mm

FEED

TF 500 500x10 500x12 500x14 500x16

Total length (mm) 4660 5270 5880 6490Drill steel length (mm) 3090 3700 4305 4915Hole depth (mm) 2830 3440 4050 4660Net weight (kg) 470 500 530 560Feed force, max. (kN) 25 25 25 25

Model TF 500Drill steel H 32 - H 35

HYDRAULIC CONTROL SYSTEM

Type THC 560Control functions-Power control Adjustable full power

Adjustable collaring power- Rotation control Adjustable rotation speed

Reversible rotation-Flushing control Water flushing

Automatic functionsCollaring, stop-and-return, anti-jamming, flushing

FEED ALTERNATIVE

Model TTF 500Type TelescopicSteel length 6/10 to 12/16 ftDrill steel H 32 - H 35

ELECTRO HYDRAULIC POWER PACK

Electrical motor 45 kW (60hp)Hydraulic pump types- Percussion, feed & boom Axial piston

variable displacement- Rotation Gear

TRAMMING DIMENSIONS

CARRIERModel CB 05Diesel engine Deutz BF4L 2011, 55 kW (74hp)- Exhaust CatalyserAutomotive hydrostatic transmissionTransfer case Drop gear Clark-HurthAxles, Front & Rear Case New Holland D45- Oscillation Rear axle, 2 x 6°- Tyres 12.00 x 20Steering Frame steering, 2 x 37°Brakes- Service Hydrostatic transmission- Emergency & parking Hydraulic oil immersed

multiple disc brakes on both axlesStabilizers 2 hydraulic jacks, front

2 hydraulic jacks, rearSafety canopy Hydraulic, FOPS-ROPS- Lowering capability 920 mmFuel tank 80 litreHydraulic tank 145 + 50 litre

WATER CIRCUIT

Water booster pump W.B.P. 2, centrifugal- Capacity 4000 l/h at 15 bar- Electric motor 4 kW (5.5 hp)Oil cooler OW 30, water-actuated counter flow- Cooling capacity 30 kW

AIR CIRCUIT

Compressor C.T. 10, screw type- Capacity 1.0 m³ at 7 barElectric motor 7.5 kW (10 hp)

ELECTRICAL SYSTEM

Total installed power 63 kWHigh / Low voltage Separate cabinetsVoltage Standard 380 - 660 VAlternative 1 000 VFrequency 50 or 60 HzStarting method Star / DeltaCable reel CRC type (Technical specification 5-503 S)- Capacity 100 m of cable 32 mm O.DLighting- Working lights 2 x 150 W, 24 V- Tramming lights 4 x 70 W, 24 V(the 2 front lights are also used as working lights)

FULL DIESEL VERSION AVAILABLE

Water-cooled engine Deutz BF4M 1012 C- Max. rating at 2300 rpm 74 kW (100 hp)Fuel tank capacity 240 litreCompressor & water pump driven by hydraulic motorsTotal machine weight 10 500 kg

OPTIONAL EQUIPMENT

DRILLING SYSTEM

Drill angle measuring instrument TMS D2.Air flushing.*) Double flushing (air/water) with CT 10 compressor.Air mist flushing kit for auxiliary water/air connection.*) Front clamping head on drill feed.

BRAKESAdditional service brake on axles.Hand pump for manual brake release.

SAFETY EQUIPMENTS

1. CANOPY2. FIRE EXTINGUISHER3. HORN, BEACON AND REVERSE ALARM4. CENTRAL LUBRICATION SYSTEM5. TRAMMING AND WORKING LIGHTS6. BRAKE LIGHTS7. SPIRIT LEVEL8. ROCK DRILL LUBRICATION WARNING KIT

THANK YOU