lec-6.torsion and sf bm compatibility mode
Post on 03-Jun-2018
234 Views
Preview:
TRANSCRIPT
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
1/25
&
.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
2/25
Consider a bar to be rigidly attached at one end and twisted at the other endby a torque or twisting moment T equivalent to F d, which is appliedperpendicular to the axis of the bar, as shown in the figure. Such a bar issa o e n ors on.
TORSIONAL SHEARING STRESS,For a solid or hollow circular shaft subject to a twisting moment T, thetorsional shearing stress at a distance from the center of the shaft is
where J is the polar moment of inertia of the section and r is the outer radius.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
3/25
ANGLE OF TWIST
The angle through which the bar length L will twist iswhere T is the torque in Nmm, L is the length of shaft in mm, G is shearmodulus in MPa J is the olar moment of inertia in mm4 D and d are
diameter in mm, and r is the radius in mm.
POWER TRANSMITTED BY THE SHAFTA shaft rotating with a constant angular velocity(in radians per second)
is being acted by a twisting moment T. The power transmitted by the shaftis
where T is the torque in Nm, f is the number of revolutions per second,and P is the power in watts.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
4/25
304 A 3 4 . 15 . D . G = 12 106 .
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
5/25
3 6 12 ? ? G = 83 G.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
6/25
A 14 . 18 5000 189 . I G = 12 106 , .
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
7/25
A 2 240 . I 12 , .
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
8/25
A 4.5 3 H
50 1 26 . C G = 83 G.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
9/25
15/16 .
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
10/25
A F. 316.
D : = 83 , = 55 , 6. F , G = 83 G , G = 28 G.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
11/25
A 50
F. 311. G = 28 G, D A.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
12/25
A F. 316.D : = 83 , = 55 , 6. F , G = 83 G , G = 28 G
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
13/25
A 3 . 2 . 2 . . . F , G = 6 106 , ,G = 12 106 .
8000 12 ?
.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
14/25
DEFIII F A BEA A
. A , .
. .
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
15/25
I , . I , .
. I , 1, 2, ( = 0
;F = 0) , (3 2 = 1).
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
16/25
( ), , , . .
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
17/25
The vertical shear at C in the figure shown in previous section is taken aswhere R1 = R2 = wL/2
If we differentiate M with respect to x:
Thus, the rate of change of the bending moment with respect to x is equal tothe shearing force, or the slope of the moment diagram at the given point isthe shear at that point. Thus
Thus, the rate of change of the bending moment with respect to x is equal tothe shearing force, or the slope of the moment diagram at the given point isthe shear at that point.Differentiate V with respect to x givesThus, the rate of change of the shearing force with respect to x is equal to theload or the slope of the shear diagram at a given point equals the load atthat oint.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
18/25
:
.
.
.
. 2, ( ) , .
, .
, .
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
19/25
.
A . A .
A
.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
20/25
B F. 425.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
21/25
C F. 426.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
22/25
B F. 428.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
23/25
B F. 444
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
24/25
B F. 446.
-
8/12/2019 Lec-6.Torsion and Sf Bm Compatibility Mode
25/25
F. 273
. A = 50 60F. C 120F. A = 6.5 106 /(F) 12.8 106 /(F) .
A F . 16.
D : = 83 , = 55 , 6. F , G = 83 G , G = 28 G.
B F. 417
.
top related