lecture 22: multistage ampsee105/fa03/handouts/lectures/lecture22.pdf · department of eecs...

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22

Lecture 22:Multistage Amps

Prof. Niknejad

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Lecture Outline

� Finish Current Mirrors

� An Example Using Cascodes

� Multistage Amps

� Cascode Amplifier: Magic!

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

The Integrated “Current Mirror”� M1 and M2 have the same

VGS

� If we neglect CLM (λ=0), then the drain currents are equal

� Since λ is small, the currents will nearly mirror one another even if Vout is not equal to VGS1

� We say that the current IREF is mirrored into iOUT

� Notice that the mirror works for small and large signals!

High Res

Low Resis

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Current Mirror as Current Source

� The output current of M2 is only weakly dependent on vOUT due to high output resistance of FET

� M2 acts like a current source to the rest of the circuit

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Small-Signal Resistance of I-Source

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Improved Current Sources

Goal: increase roc

Approach: look at amplifier output resistance results … to see topologies that boost resistance

Looks like the output impedance of a common-source amplifier with source degeneration

out oR r>>

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Effect of Source Degeneration

� Equivalent resistance loading gate is dominated by the diode resistance … assume this is a small impedance

� Output impedance is boosted by factor

( )St t m gs o Rv i g v r v= − +

1eq

m

Rg

≈

Sgs Rv v≈ −

SR t Sv i R=

( )t t m S t o t Sv i g R i r i R= + +

( )1to m S o

t

vR g R r

i= ≈ +

( )1 m Sg R+

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Cascode (or Stacked) Current Source

Insight: VGS2 = constant ANDVDS2 = constant

Small-Signal Resistance roc:

( )1o m S oR g R r≈ +

( )1o m o oR g r r≈ +

20o m oR g r r≈ >>

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Drawback of Cascode I-Source

Minimum output voltage to keep both transistors in saturation:

, 4, 2,OUT MIN DS MIN DS MINV V V= +

vOUT

iOUT

2, 2 0 2DS MIN GS T DSATV V V V> − =

4 2 4 2 4 0D DSAT GS GS GS TV V V V V V> + = + −

, 2 4 0OUT MIN GS GS TV V V V= + −

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Current Sinks and Sources

Sink: output current goesto ground

Source: output current comesfrom voltage supply

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Current Mirrors

Idea: we only need one reference current to set up all the current sources and sinks needed for a multistage amplifier.

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Multistage Amplifiers

Necessary to meet typical specifications for any of the 4 types

We have 2 flavors (NMOS, PMOS) of CS, CG, and CD and the npn versions of CE, CB, and CC (for a BiCMOS process)

What are the constraints?

1. Input/output resistance matching

2. DC coupling (no passive elements to block the signal)

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Summary of Cascaded Amplifiers

General goals:

1. Boost the gain parameter (except for buffers)2. Optimize the input and output resistances

RoutRin

Transresistance:

Transconductance:

Current:

Voltage: ∞∞

∞

00

∞

0 0

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Start: Two-Stage Voltage Amplifier

• Use two-port models to explore whether the combination “works”

CE1CE2

Results of new 2-port: Rin = Rin1, Rout = Rout2

( ) ( )1 2 1 2 2||v m in out m outA G R R G R= − × −

( )( )1 2 2 1 2||v m m in out outA G G R R R=

CE1,2

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Add a Third Stage: CC

Goal: reduce the output resistance(important spec. for a voltage amp)

CE1CE2 CC3

Output resistance:

2 2

3 3

||1 1S o ocout

m m

R r rR

g gβ β= + = +

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Using CMOS Stages

CS1CS2 CD3

Output resistance:

Voltage gain (2-port parameter):

Input resistance: ∞

( ) ( )1 1 1 2 2 2|| ||v m o oc m o ocA g r r g r r= − × −

1out

m mb

Rg g

=+

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Multistage Current Buffers

CB1 CB2

Are two cascaded common-base stages better than one?

Input resistance: Rin = Rin1

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Two-Port Models

( ) 2222022 ||||1 ocSmoutout rRrgrRR π+≅=

Output impedance of stage #1 (large)

( ) ( )02 2 2 2 2 2|| ||out m oc o o ocR r g r r r rπ β≅ =

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Common-Gate 2nd Stage

( ) 222022 ||1 ocSmoutout rRgrRR +≅=

( )2 02 2 1 1 21 || ||out out m o oc ocR R r g r r r= ≅ +

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Second Design Issue: DC Coupling

Constraint: large inductors and capacitors are not available Output of one stage is directly connected to the input of the next stage � must consider DC levels … why?

3.2V

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Alternative CG-CC Cascade

Use a PMOS CD Stage: DC level shifts upward

3.2V

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

CG Cascade: DC Biasing

Two stages can have different supply currents

Extreme case:IBIAS2 = 0 A

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

CG Cascade: Sharing a Supply

First stage has no currentsupply of its own � its outputresistance is modified

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

The Cascode Configuration

DC bias:

Two-port model: first stage has no current supply of its own

Common source / common gatecascade is one version of a cascode(all have shared supplies)

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Cascode Two-Port Model

CS1* CG2

Output resistance of first stage = 1,, * oCSdownCSoutrRR ==

Why is the cascode such an important configuration?

2 1 2|| (1 )out oc m o oR r g r r+�

1m mG g=

inR = ∞

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Miller Capacitance of Input StageFind the Miller capacitance for Cgd1

Input resistance to common-gatesecond stage is low �gain acrossCgd1 is small.

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Two-Port Model with Capacitors

Miller capacitance: 1)1(1 gdvCM CAC

gd−=

1

11 1

2 2

1( || ) 1

gd

mvC m o

m m

gA g r

g g= − ≈ − = −

12M gdC C=

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Generating Multiple DC Voltages

Stack-up diode-connected MOSFETs or BJTs and run a reference current through them � pick off voltages from gates or bases as references

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Multistage Amplifier Design Examples

Start with basic two-stage transconductance amplifier:

Why do this combination?

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Two-Stage Amplifier Topology

Direct DC connection: use NMOS then PMOS

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Current Supply Design

Assume that the reference is a “sink” set by a resistor

Must mirror the reference current and generate a sink for iSUP 2

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Use Basic Current Supplies

Department of EECS University of California, Berkeley

EECS 105 Fall 2003, Lecture 22 Prof. A. Niknejad

Complete Amplifier Topology

What’s missing? The device dimensions and the biasvoltage and reference resistor