manual gratis chery tig go
Post on 09-Mar-2016
153 Views
Preview:
DESCRIPTION
TRANSCRIPT
-
El siguiente Manual del Chery Tiggo es una MUESTRA GRATIS de los Manuales que puedes
adquirir en la siguiente direccin:
http://www.autodaewoospark.com/manuales-chery-tiggo-servicio-usuario.php
Atentamente,
Jorge E. Penagos P. http://www.autodaewoospark.com
-
Instrument Panel FeaturesLHD Instrument Panel Features
1 - Air Outlet 5 - Radio 9 - Hazard Warning Flasher Switch 13 - Front Ashtray 17 - Hood Release Lever2 - Steering Wheel 6 - Passenger Side Airbag 10 - Cigarette Lighter 14 - Cruise Control Switch 18 - Headlight LevelingSwitch3 - Instrument Cluster 7 - Glove Box 11 - RH Heated Seat Switch 15 - Remote Audio SystemControls 19 - Rear Fog Light Switch4 - Driver Side Airbag 8 - Climate Control Panel 12 - LH Heated Seat Switch 16 - Dimmer Control Switch 20 - Front Fog Light Switch
78 YOUR INSTRUMENT PANEL
Chery Automobile Co., Ltd.
-
Instrument Cluster
80 YOUR INSTRUMENT PANEL
Chery Automobile Co., Ltd.
-
Hazard Warning FlasherThe hazard switch is located
on the instrument panel,
above the climate control
panel. Depress the switch to
activate both cluster indicators and all
front and rear directional signals. De-
press the switch again to turn the Haz-
ard Warning Flashers off. This is an
emergency warning system and it
should only be used for emergencies.
Use it when your vehicle is disabled or
creating a safety hazard for other mo-
torists.
The hazard warning flashers will con-
tinue to operate even though the igni-
tion switch is on the LOCK position.
NOTE: With extended use, the hazardwarning flashers may drain the battery.
Jacking and Tire ChangingJack LocationThe jack is stowed under the load
floor in the cargo area.
NOTE: The maximum working load ofthe jack is 800 kg.Spare Tire LocationThe spare tire is stowed on the back
door.
Spare Tire Removal
Release the spare tire cover clasp.
Remove the spare tire cover.
Jack Storage Location
Spare Tire Location
Releasing The Spare Tire Cover Clasp
98 IN CASE OF AN EMERGENCY
Chery Automobile Co., Ltd.
-
Jack Engagement Locations
100 IN CASE OF AN EMERGENCY
Chery Automobile Co., Ltd.
-
A blown fuse can be identified by the
melted fuse wire.
Fuse Color AmperageAuburn 5 ABrown 7.5 ARed 10 ABlue 15 A
Yellow 20 AGreen 30 A
Fuse Color AmperagePink 40 A
Yellow 60 A
Towing A Disabled Vehicle
NOTE: Your vehicle is equipped withtow hooks at both the front and rear.
CAUTION!Observe the following guidelines when
towing the vehicle:
Tow the vehicle slowly and smoothly
to avoid damage.
If the vehicle needs to be steered
while being towed, the ignition
switch must be in the ON position,
not in the LOCK or ACC position.
Power brake and power steering as-
sist is not unavailable when the en-
gine is off, the required operational
force is increased significantly.
(Continued)
CAUTION! (Continued) Do not attempt to tow this vehicle
from the front with sling type tow-
ing equipment. Damage to the front
fascia will occur.
Removing and InstallingVehicle BatteryThe following steps must be taken
when removing and installing the bat-
tery:
Turn the ignition switch and all elec-
trical devices off.
Remove the negative (-) battery
cable.
104 IN CASE OF AN EMERGENCY
Chery Automobile Co., Ltd.
-
Proper Maintenance Of Your VehicleEngine Compartment - 1.6L / 1.8L / 2.0L
1 - Power Steering Fluid Reservoir 6 - Power Fuse Box2 - Engine Oil Fill 7 - Engine Oil Dipstick3 - Brake Fluid Reservoir 8 - Cooling System Pressure Cap4 - Air Cleaner Filter 9 - Washer Fluid Bottle5 - Battery 10 - Engine Coolant Reservoir
112 PROPER MAINTENANCE OF YOUR VEHICLE
Chery Automobile Co., Ltd.
-
Engine Compartment - 2.4L
1 - Power Steering Fluid Reservoir 6 - Battery2 - Engine Oil Fill 7 - Power Fuse Box3 - Engine Oil Dipstick 8 - Cooling System Pressure Cap4 - Brake Fluid Reservoir 9 - Washer Fluid Bottle5 - Air Cleaner Filter 10 - Engine Coolant Reservoir
PROPER MAINTENANCE OF YOUR VEHICLE 113
Chery Automobile Co., Ltd.
-
Service Manual for CheryTiggo(T11) Engine Section
2
Chapter 1 Overview Engine used in Chery Tiggo car is MITSUBISHI 4G64 (2.4L) and 4G63 (2.0L)
model engine, which adapt single-overhead-camshaft, 4-cylinder 16-valve and multi-point sequential injection.
I. Technical Data
1. Engine Mode Number Indication
Multi-point sequential injection 44 valve structure Single-overhead-camshaft
Design serial number Product serial Gasoline engine 44 cylinder structure
2.Engine Number Position
Engine No.
-
Service Manual for CheryTiggo(T11)Engine Section
12
Chapter 2 Engine Structure
Features
1.Cylinder Cover Structure
Features
Cam bearing hole
Spark plug pipe
Inlet air duct
2.Cylinder Cushion Structure
3.Spark Plug Position
Exhaust air duct
Spark plug
Inlet air duct
Piston
Cylinder cover is made of horniness
aluminium alloy, which is firstly
low-pressure-molten and then
machining.
Four-valve structure is applied and
its advantage is increasing
emission channel area and
decreasing valve movement inertia.
Agile fiberboard structure is
applied. Many 1.5mm-diameter
through holes are pressed in the
steel board and fiber liquid mixture
is filtered through steel board. And
then sealant is sprayed on both
sides of agile broad and the
important part is additionally
sprayed with seal thread.
Spark plug is located in the center
of chamber, which may let flame
reach each chamber corner at almost
the same time.
-
Service Manual for CheryTiggo(T11) Engine Section
23
Chapter 3 Valve gear
I. Timing belt
Disassembling steps
1. front upper cap of timing belt
2. front lower cap of timing belt
3. power steering bracket
4. crankshaft position sensor
5. timing belt
6. tensioning gear
7. tensioner arm
8. automatic tensioner
9. idler
10. oil pump pulley
11. crankshaft screw bolt
12.crankshaft
timing pulley
13.flange
14.tensioner B
15.timing belt B
16. pulley of upper balance shaft
17.bushing
18.crankshaft
timing pulley B
19.right bracket component of engine
20.screw bolt of camshaft pulley
21.camshaft timing pulley
Disassembling illustration
8.8N.m
8.8N.m
-
T11 Service Manual Transmission
92
Section Technical Data and Precautions
1. Schematic Diagram
1. Idler Assembly
2. Pinion Gear, 4th
Gear
3. 3rd
-4th
Gear Synchronizer
4. Pinion Gear, 3rd
Gear
5. Transmission Housing
6. Clutch Box
7. Release Bearing Saddle
8. Input Shaft
9. Output Shaft
10. Differential Assembly
11. Driven Gear of 1st Gear
12. 1st-2
nd Gear Synchronizer
13. Driven Gear, 2nd
Gear
14. Driven Gear, 5th
Gear
15. Synchronizer of 5th
-Gear and Reserve Gear
16. Gear, Reverse Gear
Schematic Diagram
-
T11 Service Manual Transmission
118
Section Clutch Box
1. Clutch box
2. Oil seal-input shaft
3. Bearing-gear shifting mechanism
4. Output shaft front bearing
5. Oil seal-differential
6. Front/rear bearing of differential
7. Buttonhead-seat release fork
8. Release bearing race
9. Bolt GB5787 M612 10. Speedometer banking cover
11. Pin GB119 A1020 12. Magnetic assembly
13. Bush-gear shifting mechanism
-
T11 Service Manual Chassis System
20
Installation of Parking Brakes
1. Replacement of Parking Brake Shoes
1) Removal
a. Remove the tire.
b. Remove brake caliper, and refer to the section of "Disc brake" to replace the bracket of brake
caliper.
c. Refer to the replacement of brake disc to remove rear brake disc.
d. Remove the rear wheel hub units.
Remark: properly align the four holes in the
brake hub units to the corresponding fixing
bolts of brake elements.
e. Remove the actuator of parking brake.
f. Remove the brake shoes.
-
T11 Service Manual Chassis System
40
Front left wheel sensor
Battery
Combination Instrument
Brake Indication Lamp
Ignition Switch
Diagnostic Interface
Brake Switch
Front right wheel sensor
Rear left wheel sensor
Rear right wheel sensor
-
Chery T11 Service Manual Body and Accessories
-28-
3) Unplug the high/low beam headlamp.
4) Remove the three fixing bolts of headlamp
assembly.
5) Remove the headlamp assembly carefully.
6) Install in the reversed sequence.
Torque:
Headlamp fixing 61Nm
PART No.: T11-3772025 (3 pcs)
4. Replacement of Headlamp Bulbs
Replacing of bulbs for high beam and low
beam headlamp.
1) Remove the back cover of headlamp.
2) Remove the bulb clip.
3) Remove the bulbs for high beam and
dipped headlamp.
4) Remove the used bulbs, and replace them
with new bulbs.
Fixing point
3.pdf4.pdf5.pdf1-Introduccion (4).pdf
3.pdf4.pdf5.pdf1-Introduccion (4).pdf
3.pdf4.pdf5.pdf1-Introduccion (4).pdf
3.pdf4.pdf5.pdf1-Introduccion (4).pdfSection Technical Data and Precautions1. Schematic DiagramSchematic Diagram
3.pdf4.pdf5.pdf1-Introduccion (4).pdfSection Clutch Box
3.pdf4.pdf5.pdf1-Introduccion (4).pdf Installation of Parking Brakes1. Replacement of Parking Brake Shoes
3.pdf4.pdf5.pdf1-Introduccion (4).pdf
3.pdf4.pdf5.pdf1-Introduccion (4).pdf4. Replacement of Headlamp Bulbs
top related