nov manually operated power slip
Post on 19-Oct-2015
1.301 Views
Preview:
TRANSCRIPT
-
REFERENCEPS15 / PS16
VarcoBJ BVNijverheidsweg 454879 AP Etten-LeurP.O. Box 174870 AA Etten-LeurThe NetherlandsTel + 31-76-5083000Fax + 31-76-5046000www.nov.com
DOCUMENT NUMBER
50000845-MAN-001REV
A
www.nov.com
PS15 Manually operated Power SlipPS16 Pneumatically operated Power Slip
PS15/16
www.nov.com
Downhole Solutions
Drilling Solutions
Engineering & Project Management
Lifting & Handling Solutions
Production Solutions
Supply Chain Solution
Tubular & Corrosion Control Solutions
Well & Completion Solutions
2006 National Oilwell Varco
All brands listed are registered trademarks of National Oilwell Varco.
Advanced WireclothAktroAlbins EnterprisesAmClydeBaylorBest Flow ProductsBLMBowenBrandtCabotCardwellChimo EquipmentContinental EmscoCooperCrestexCustom Die & InsertDELCODrecoDSS (Drilling Support Services)Eastern Oil ToolsElmarEMD (Electro Motive Division)FibercastFidmashFlanagan IronworksFranksFritz CulverGator HawkGregoryGriffithHALCOHarrisburgHITECHSI (Houston Scientific International)Hydra RigHydraliftIdecoIPS (Integrated Power Systems)IRI InternationalKoomeyKremcoLOUIS ALLISLuckerM & WM/D TotcoMatheyMATTCOMcElroy Marine MachineryMiller Oilfield
MissionMoldeMonoMonofloNationalNational OilwellOil Tools SolutionsOilwellOmega PumpsPacific InspectionPCEPeck-O-MaticPEPProcon AsQuality TubingRebound RigRMI (Rig Manufacturing International)Roberds JohnsonROSS HILLRuckerRussell SubsurfaceSauermanShafferShearerSkytop BrewsterSmith FiberglassSpecialtySSRStlprodukterStar FiberglassTech PowerTEM (Tulsa Equipment Manufacturing)Texas Oil ToolsTS&MTuboscopeTurner Oilfield ServiceUNIFLEXUnit cranesUniversalUSF (Utility Steel Fabricators)VarcoVectorVersatechWeston Oilfield EngineeringWheatley GasoWildcat ServicesWilsonWoolley
CorporateHeadquarters
10000 Richmond AvenueHouston, Texas 77042United StatesPhone: 713 346 7500Fax: 713 435 2195
National Oilwell Varco Brands
US
ER
S M
AN
UA
L
REFERENCE DESCRIPTIONPower Slips
This document contains proprietary and confidential information which is the property of National Oilwell Varco, L.p, its affiliates or subsidiaries (all collectively referred to hereinafter as "NOV"). It is loaned for limited purposes only and remains the property of NOV. Reproduction, in whole or in part, or use of this design or distribution of this information to others is not permitted without the express written consent of NOV. This document is to be returned to NOV upon request or upon completion of the use for which it was loaned. This document and the information contained and represented herein is the copyrighted property of NOV.
October 2008
-
www.nov.com
PS16
PS15
Users ManualPS15 Manually operated Power Slip
PS16 Pneumatically operated Power Slip
REFERENCEPS15/16
REFERENCE DESCRIPTIONPower Slips
This document contains proprietary and confidential information which is the property of National Oilwell Varco, L.p., its affiliates or subsidiaries (all collectively referred to hereinafter as "NOV"). It is loaned for limited purposes only and remains the property of NOV. Reproduction, in whole or in part, or use of this design or distribution of this information to others is not permitted without the express written consent of NOV. This document is to be returned to NOV upon request or upon completion of the use for which it was loaned. This document and the information contained and represented herein is the copyrighted property of NOV.
VarcoBJNijverheidsweg 454879AP Etten-LeurTel: +31-76-5083000Fax: +31-76-5046000
DOCUMENT NUMBER
50000845-MAN-001-MAN-001REV
A
-
Document number 50000845-MAN-001Revision APage 2 of 50
www.nov.com
Revision History
Change Description
A 08.10.2008 Changed PGF BdP AK- 30.10.2007 Issued for Implementation PGF BdP AK
Rev Date Reason for issue Prepared Checked Approved
Revision Change DescriptionA Changed chapter Description; replaced Slip body with Slip - First Issue
-
Table of Contents
Document number 50000845-MAN-001Revision APage 3 of 50
www.nov.com
General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Notes, Cautions, and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Personnel Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Recommended Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6General System Safety Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Replacing Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Proper Use of Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Identification numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Warning plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Design safety factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7CE marking PS15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7CE marking PS16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7PS15/16 restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Specifications, requirements & sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Major components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Main assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Top cover assembly (PS16 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Air cylinders (PS16 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Bowl assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Slip assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Guide ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Lubrication and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Recommended General Purpose EP grease . . . . . . . . . . . . . . . . . . . . . . . . . 17
Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Replacing the slip inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Replacing the guide ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Replacing the bowl hinge pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Magnetic Particle Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Annual inspection (power slip in use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Non-destructive examination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Evaluations of indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23For equipment delivered in accordance with API 8A & 8C PSL 1 . . . . . . . . . . 23For equipment delivered in accordance with API 8C PSL 2 . . . . . . . . . . . . . . 24
Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
-
Table of Contents
Document number 50000845-MAN-001Revision APage 4 of 50
www.nov.com
(Paper) slip test procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Shop repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Changing dies/inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Installation and commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Pre-installation check list PS15/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Installation PS15/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Installation PS16 control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Check out procedure PS15/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Lifting the PS15/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PS16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29PS15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Operation PS15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Theory of operation PS16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting the power slips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Releasing power slips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Procedure changing PS16 slips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Assembly and dis-assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Before (dis)assembly of the PS make sure: . . . . . . . . . . . . . . . . . . . . . . . . . . 33Torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Overview possible problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37ATEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Storage, transport & scrapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Scrapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Lubrication before storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Torque values (US) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Torque values (metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Drawings & Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41PS15 main assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41PS16 drawing numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44PS16 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Table 1; PS16 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Table 1; PS16 Parts list (cont.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Control system parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Figure 15; slip assembly and parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
-
Document number 50000845-MAN-001Revision APage 5 of 50
www.nov.com
1: General Information
General informationThis manual contains installation, operation, maintenance and parts information. Information in this manual should enable qualified personnel to install, operate and troubleshoot this system. Every effort has been made to ensure the accuracy of the information contained herein. National Oilwell Varco (NOV) will not be held liable for errors in this material, or for consequences arising from misuse of this material.
ConventionsNotes, Cautions, and Warnings
Notes, cautions, and warnings provide readers with additional information and advise the reader to take specific action to protect personnel from potential injury or lethal conditions. They may also inform the reader of actions necessary to prevent equipment damage. Please pay close attention to these advisories
IllustrationsIllustrations (figures) provide a graphical representation of equipment components or screen snapshots for use in identifying parts or establishing nomenclature, and may or may not be drawn to scale.
For component information specific to your application, see the technical drawings included with your NOV documentation.
Safety RequirementsNOV equipment is installed and operated in a controlled drilling rig environment involving hazardous situations. Proper maintenance is important for safe and reliable operation. Procedures outlined in NOV manuals are the recommended methods of performing operations and maintenance.
Personnel TrainingAll personnel performing installation, operations, repair, or maintenance procedures on the equipment, or those in the vicinity of the equipment, should be trained on rig safety, tool operation, and maintenance to ensure their safety.
Note: The note symbol indicates that additional information is provided about the current topics.
Caution: The caution symbol indicates that potential damage to equipment or injury to personnel exists. Follow instructions explicitly. Extreme care should be taken when performing operations or procedures preceded by this caution symbol.
Warning: The warning symbol indicates a definite risk of equipment damage or danger to personnel. Failure to observe and follow proper procedures could result in serious or fatal injury to personnel, significant property loss, or significant equipment damage.
CAUTION: To avoid injury to personnel or equipment damage, carefully observe requirements outlined in this section.
CAUTION: Personnel should wear protective gear during installation, maintenance, and certain operations.
-
Document number 50000845-MAN-001Revision APage 6 of 50
1: General Information
www.nov.com
Recommended ToolsService operations may require the use of tools designed specifically for the purpose described. NOV recommends that only those tools specified be used when stated. Ensure that personnel and equipment safety are not jeopardized when following service procedures or using tools not specifically recommended by NOV.
General System Safety PracticesThe equipment discussed in this manual may require or contain one or more utilities, such as electrical, hydraulic, pneumatic, or cooling water.
Isolate energy sources before beginning work. Avoid performing maintenance or repairs while the equipment is in operation. Wear proper protective equipment during equipment installation, maintenance, or repair.
Replacing Components Verify that all components (such as cables, hoses, etc.) are tagged and labeled during
assembly and disassembly of equipment to ensure correct installment. Replace failed or damaged components with genuine NOV parts. Failure to do so could
result in equipment damage or injury to personnel.Routine MaintenanceEquipment must be maintained on a routine basis. See the service manual for maintenance recommendations.
Proper Use of EquipmentNOV equipment is designed for specific functions and applications, and should be used only for its intended purpose.
Identification numbers
You will find the identification of the tool stamped into the top plate.
Lifting
The lifting procedures should carefully be observed and carried out according to the manual.
Routine Maintenance
Equipment must be maintained on a routine basis. See this manual for maintenance recommendations.
CAUTION: Read and follow the guidelines below before installing equipment or performing maintenance to avoid endangering exposed persons or damaging equipment.
CAUTION: Failure to conduct routine maintenance could result in equipment damage or injury to personnel.
CAUTION: Failure to conduct routine maintenance could result in equipment damage or injury to personnel.
-
Document number 50000845-MAN-001Revision APage 7 of 50
1: General Information
www.nov.com
Warning plates
Label (typical) p/n # 50001003Design safety factor
The design-safety factor and design verification is in accordance with requirements of API specification 7K.
CE marking PS15
The PS15 complies with the Machinery Directive 98/37/EC.
The marking is as follows:
CE marking PS16
The PS16 complies with the Machinery Directive 98/37/EC and the Directive 94/9/EC Equipment and protective systems in potentially explosive atmospheres
The marking is as follows:
PS15/16 restrictions Only use the PS in combination with Varco style slips. Do not exceed the crush load of the pipe. Do not use the PS16 for drilling purposes with 6-5/8 slips
WARNING: The warning plates must be present on the PS. Do not remove the labels.
WARNING: Care should be taken to avoid creating possible ignition sources, like sparks, due to improper use of the tool in combination with other equipment.
Equipment Type
Model Number
Serial number
Size Range
Rating
Weight
Date of Mfg.
Manufactured by National Oilwell Varco, P.O. Box 17, Etten-Leur, The Netherlands
NL
Pa
rt N
um
be
r 5
00
01
00
3Kg. Lbs.
Ex
Ex II 2G T5
-
Document number 50000845-MAN-001Revision APage 8 of 50
1: General Information
www.nov.com
-
Document number 50000845-MAN-001Revision APage 9 of 50
2: Specifications
www.nov.com
General specificationsSpecifications, requirements & sizesSubject Description PS15 PS16
Size and rating - Fully automatic, non-rotating, air operated
Manually operated, non rotating -
Drill pipe sizes - 3-1/2" to 6-5/8" O.D.
Drill pipe sizes 3-1/2" to 5" O.D. -
Rotary table:27-1/2", 37-1/2" to 9-1/2" Equipped with Varco pin drive master bushings
27-1/2", 37-1/2" to 9-1/2" Equipped with Varco pin drive master bushings
Air Air supply - Regulated, 90 psi (482 KPa)
Control system: - Air pilot operated, hand or foot controlled
Air hoses: - Low pressure, 23', equipped with QD fittings
Guides Guide ring: Flame hardened, replaceable Flame hardened, replaceable
Slips Slip inserts: Flame hardened, replaceable Flame hardened, replaceable
Slip: 4-1/2" for 3-1/2" to 4-1/2" drill pipe 4-1/2" for 3-1/2" to 4-1/2" drill pipe
Slip: 5-1/2" for 4-1/2" to 5-1/2" drill pipe 5-1/2" for 4-1/2" to 5-1/2" drill pipe
Slip: - 6-5/8" for 6-5/8" drill pipe onlyDimension and weights Weight: Appr. 1,040 lb (472 kg) Appr. 1,600 lb (727.3 kg)
Width: 33" (838 mm) 32" (813 mm)
Overall height: Slip set, in (mm) 33.5 (851) 39.9" (1013 mm) Slips Released, in (mm) 41.5 (1,054) 48.4" (1229 mm)
Height above rig floor: Slips set: 11 (279) 17.5"(445 mm)
Slips released: 19 (483) 26.0" (660 mm)
-
Document number 50000845-MAN-001Revision APage 10 of 50
2: Specifications
www.nov.com
General description
The Varco PS15 Power Slip is a manually operated slip for the setting and releasing of drill pipe slips for 3-1/2" to 5-1/2" drill pipe.
The Varco PS16 Power Slip is a fully automatic, remote controlled, air operated system for the setting and releasing of drill pipe slips for 3-1/2" to 5-1/2" drill pipe (Figure 1). The PS16 can accommodate 6-5/8" drill pipe, but only as a tripping tool.
Both the PS15 and the PS16 eliminates the difficult and sometimes dangerous job of hand setting and lifting of drill pipe slips. The PS15 Power Slips can be set by the crew members simply standing on the slip set ring. The PS15 slips use coil springs as a counter balance to offset the weight of the slips when in the upper, or, released position. The PS16 power slips can be controlled by either a hand or foot operated remote control valve. The PS16 slips are set by gravity and released by applied air pressure. The PS15/16 is designed to fit into 27-1/2" and 37-1/2" to 49-1/2" rotary tables equipped with Varco pin drive master bushings. The PS15/16 is a non-rotating unit designed for use with the Varco top drive drilling system.
CAUTION: Do not use 6-5/8" drill pipe with the PS16 to drill ahead.
Step ring
Spring
Lock Hanger
Body
Guide ring
Slip
Body
Hinge pin
PS15 major components
-
Document number 50000845-MAN-001Revision APage 11 of 50
2: Specifications
www.nov.com
Major components
Table 1 lists the part numbers for the various available configurations and common replacement parts.
*Air controls can be specified for hand or foot operation.
Slipassembly
Guide ring
Bowlassembly
Aircylinder (2)
Split elevator support
Q.D. coupler
Q.D.coupler
Reliefvalve
PS16 major
Drill pipe size (inch)
PS16 Complete with pipe guide ring, slips/inserts
PS16 Complete with pipe guide ring, slips/inserts, controls* and hoses
Replacement slip assembly (1 per system)
Replacement insert sets (1 per system)
PS15 Replacement guide ring (1 per system)
PS16 Replacement guide ring (1 per system)
3-1/2 18172-45-35 78181-45-35 7686 2163-16B-32 18420 79011-14 18172-45-40 78181-45-40 7685 2164-16B-32 18140 79011-24-1/2 18172-45-45 78181-45-45 7684 2165-48 18140 79011-24-1/2 18172-55-45 78181-55-45 7691 2168-16B-32 18140 79011-25 18172-55-50 78181-55-50 7690 2169-16B-32 18226 79011-35-1/2 18172-55-55 78181-55-55 7689 2170-48 18148 79011-46-5/8 - 78181-76-66 7696-A 2032-6B-12 - 7799
-
Document number 50000845-MAN-001Revision APage 12 of 50
2: Specifications
www.nov.com
Main assembly
Each PS16 configuration consists of the following major assemblies (Figures 2 and 3): Top cover assembly, Air cylinders, Bowl assembly, Slip assembly, Guide ring &
Control system
Figure 2; PS16 Power Slip (side view)
NOTE: The PS15 assembly is essentially the same as the PS16 assembly without the pneumatic parts, but with springs and a step ring.
Top plate
-
Document number 50000845-MAN-001Revision APage 13 of 50
2: Specifications
www.nov.com
Figure 3. PS16 Power Slip (top view)
Top cover assembly (PS16 only)
The top cover assembly consists of two identical halves. The flat, top surface is designed to accommodate TDS elevators while drilling to the floor. The rod ends of the two air cylinders connect to the top of the cover assembly with hex-head screws.
At the bottom of the top cover assembly are four clevises for mounting slip assembly hangers and four holes which accommodate the guide pin studs. The studs are attached to the top cover with special torque nuts torqued to 250 ft lb (338 Nm).Air cylinders (PS16 only)
The two air cylinders lift the top cover assembly and attached slip assemblies approximately 8-1/2" on the application of 90 psi air. Lifting the slip assemblies releases the drill string.
Each air cylinder rod has an 8-1/2" stroke. They are tapped in the end to accommodate the 1" hex-head screw used to attach the rod to the top cover assembly.
Each air cylinder has four 1/2" tapped ports top and bottom (2 on each side) to accommodate 1/2" NPT fittings for the control system. The air cylinders attach to the bowl assembly with a special bottom bracket and 1/2" screws.
Bowl assembly
The PS15/16 bowl assembly consists of two halves connected with a bowl hinge pin to enable the installation and removal of the power slips around the drill string.
Inside the bottom of the bowl assembly is a groove to accommodate the mounting of the replaceable guide ring. Four guide pins (2 on each side), that attach to the top
Springs
-
Document number 50000845-MAN-001Revision APage 14 of 50
2: Specifications
www.nov.com
cover assembly provide stability to the system. Each guide pin bushing has a grease fitting for lubrication.
Slip assembly
The slip assembly provides the means for gripping the drill string. Four slip segments are required for each PS15/16. The slip segment consists of a slip body, slip hanger, slip inserts and attaching hardware (Figure 4).The slip is available in three sizes. The 4-1/2" slip is used for drill pipe sizes 3-1/2" to 4-1/2". The 5-1/2" slip is used for drill pipe sizes from 4-1/2" to 5-1/2". The 6-5/8" slip is only used for tripping.
Slip inserts vary for each pipe size and depend on the size of the slip used (see the table in Figure 5).
Figure 4. Slip segment
-
Document number 50000845-MAN-001Revision APage 15 of 50
2: Specifications
www.nov.com
Guide ring
The guide ring keeps the drill string centered to enable proper operation of the slips. The guide ring also provides channels for the PS16 slip assemblies, keeping them spaced evenly, assuring that the drill pipe is gripped evenly during slip setting. The guide ring is precision machined and consists of two matched halves to accommodate the opening of the bowl assembly.
Because excess guide ring wear is detrimental to PS16 performance, monitor internal guide ring surface wear closely. Replace the guide ring if wear exceeds 3/16" (4.76 mm)
Figure 5. PS15/16 Guide ring
Drill pipe size
Guide ring P/N
Guide ring I.D. (new)
Max. allowable guide ring I.D.
3-1/2 79011-1 6.00 6-3/164 & 4-1/2 79011-2 7-1/4 7-7/165.00 79011-3 7-1/2 7-11/165-1/2 79011-4 8.00 8-3/16
9.34 dia
10.68 dia
I.D. wearmeasurement
-
Document number 50000845-MAN-001Revision APage 16 of 50
2: Specifications
www.nov.com
Control system
The PS16 control system consists of a 250 psi (1,723 KPa) filter/regulator, inline (pilot operated) valve, hand operated pilot valve, check valve and miscellaneous connecting hoses and fittings (Figure 6). The hand operated valve is located near other controls for rig floor equipment. A latch on the valve locks it into either SET or RELEASE positions. The filter/regulator controls air pressure at 90 psi (620 KPa) to operate the power slips. Loss of air sets the slips.
NOTE: The PS16 control system can be specified for either hand or foot control.
Pneumatic hosewith quickdisconnect
PS-16
90 POS 2POS 1
Main in
Pilot in
Control schematic
Handlelatch
fromair
egulator
Hand operatedcontrol valve
Air pilot
tocontrolvavle
Lubricatorassembly
Filterregulator250 PSI
Inline valve(pilot operated)
Check valvepilot operated
Air cylinder
-
Document number 50000845-MAN-001Revision APage 17 of 50
3: Lubrication and maintenance
www.nov.com
Lubrication and maintenance
Recommended General Purpose EP grease
CAUTION: Practice safety in all performances of operation and maintenance and use approved safety methods, materials and tools. Keep hands away from any pinch point or undesignated areas; use provided handles for operating the PS15/16.
Lube code description
Above -20 C Below -20 C
Castrol MP grease n/aChevron Avi-Motive Avi-Motive WExxon Lidok EP2 Lidok EP1Gulf Gulfcrown EP2 Gulfcrown EP1Mobil Mobilux EP2 Mobilux EP1Shell Alvania EP2 Alvania EP1Texaco Multifak EP2 Multifak EP1Union Unoba EP2 Unoba EP1
NOTE: Do not use pipe dope as a lubricant on PS15/16 Power Slips. Pipe dope is not a lubricant and if used causes slips to stick and foul the slip inserts.
NOTE: To reduce the chance of inserts seizing in the insert slots, NOV recommends to remove inserts after each job, preserve the insert slot with light machine oil, EP-2 grease or any other preservation fluid that does not affect the friction coefficient with string weight compared to a none preserved insert slot.
-
Document number 50000845-MAN-001Revision APage 18 of 50
3: Lubrication and maintenance
www.nov.com
InspectionsDaily inspections1. Check exterior for worn and damaged parts2. Check for loose and missing parts3. Check all pins are properly locked4. Check for worn hinge pins and hinge pin bores by trying to vertically move jaws from lever5. Check for proper latch engagement of pedal.6. Check that all bolts and nuts are secured by lock wire, lock tabs or cotter pins7. Brush dies clean and check for wear.8. Grease hinge pins through grease nipples.9. Make sure the slip assembly inserts are free of mud and other debris.10.Check the backs of slip bodies for stress cracks or abnormal wear.11.Check and drain the filter/regulator bowl of any collected water.12.PS16 only: Check the air system lubricator.
Monthly inspections1. Take a strain on the string and release the slips.2. Unlock the power slips from the master bushing.3. Attach a hoist and lift the power slips clear of the master bushing.4. Open and guide the slips around the drill string and place on rig floor OPEN.5. Inspect the bowl hinge pin and holes for excess wear that could cause bowl halves to wobble when closed.
Replace the hinge pin, if necessary.6. Remove the guide ring and check the inside diameter for wear. If the inside diameter is worn more than 3/
16" (4.76 mm), replace the guide ring.7. Remove the cotter pins from the guide pin torque nuts and check for a minimum of 250 ft lb tightness.8. Check the cotter pins on the slip hangers. Inspect the slip and hanger holes for any enlargement that may
indicate wear. If worn, replace the slip assembly.9. Check the backs of the slip body for wear or stress cracks. If cracks or excess wear is detected, replace the
slip body.10.PS16 only: Make sure that the roll pins through the screws attaching the top cover to the air cylinder rods
are in place. If a pin is missing or sheared off, replace it and retighten the top cover.11.Check the slip inserts for excess wear. Remove the inserts and check the backs for stress cracks. Replace
if necessary.12.Lubricate PS as specified in the Lubrication section and reinstall.
3 Monthly inspections1. Carry out a paper test inspection
Maintenance proceduresMaintenance procedures assume the PS15/16 is removed from the master bushing and is on the rig floor, opened, with a hoist attached. Refer to Figure 10 when performing the procedures in this section.Procedure rplacing the slip assembly1. Order a replacement slip assembly(s)2. Remove the cotter pins attaching the slip assembly hanger to the top cover.3. Drive the pin out of the top cover clevis and the slip hanger.4. Remove and discard the slip assembly.5. Reverse the above steps to install a new slip assembly.
-
Document number 50000845-MAN-001Revision APage 19 of 50
3: Lubrication and maintenance
www.nov.com
Figure 10. PS16 exploded view
Split elevator support
Aircylinder
Slip hanger
Insert
Slip body
Bowl assembly
Guide ring
Air cylinde
Guard
-
Document number 50000845-MAN-001Revision APage 20 of 50
3: Lubrication and maintenance
www.nov.com
Replacing the slip inserts
Order a replacement insert set per Table 1.
1. Remove and discard the screws and lockwashers retaining the old slip inserts in the slip body.
2. Remove and discard the old inserts.3. Inspect the slip body dovetail slots for damage. If damaged, replace the slip
assembly.4. Slide new inserts into the slip body (Figure 11).
5. Use new lock washers and screws supplied with the insert set to retain inserts.6. Tighten screws with the allen wrench provided.
NOTE: The first four digits of the insert P/N indicates the size of the inserts. The next four digits indicates the quantity of inserts. A B after the number indicates a beveled insert.
Procedure
NOTE: When replacing insert sets with both beveled and non-beveled inserts, the inserts with the beveled edges must be inserted into dovetail slots on the top and bottom with beveled edges out.
-
Document number 50000845-MAN-001Revision APage 21 of 50
3: Lubrication and maintenance
www.nov.com
Replacing the guide ring
1. Order a new guide ring per Table 1.2. Remove the four hex-head screws and washers attaching the guide ring to the PS16 bowl
assembly.3. Remove and discard the old guide ring.4. Install a new guide ring.
Replacing the bowl hinge pin
1. Order a replacement hinge pin (P/N 18121) and a cotter pin (P/N 51402-12).2. Remove the old cotter pin and discard.3. Drive the hinge pin up and out of bowl halves.4. Install a new pin and cotter pin.
Procedure
NOTE: Guide rings come in matched pairs or halves. Check that numbers stamped on the guide ring halves match before installing (Figure 7).
Procedure
-
Document number 50000845-MAN-001Revision APage 22 of 50
3: Lubrication and maintenance
www.nov.com
Lubrication
1. Lubrication of the PS15/16 consists of charging the four grease fittings with EP grease once each trip and maintaining the oil level in the lubricator on the discharge of the filter/regulator.
2. PS16 only: Check the level of oil in the lubricator located on the discharge of the PS16 filter/regulator. Fill the lubricator to operating level with appropriate oil.
3. Each trip charge the four grease fittings located on the PS15/16 guide pins with the appropriate general purpose EP grease (Figure 16). In addition, brush a generous quantity of EP grease onto the backs of the PS15/16 slip bodies.
Figure 16; PS16 lubrication points.
Procedure
NOTE: PS16 only: Use only 10-wt hydraulic oil or non-detergent motor oil as a lubricant in the air system. Use of any other type of oil or synthetic additive causes the seals in the air valves to swell and cease to function.
Slipassembly
(4)
Guide ring
Bowlassembly
Aircylinder (2)
Split elevator support
Q.D. coupler
Q.D.coupler
Reliefvalve
-
Document number 50000845-MAN-001Revision APage 23 of 50
3: Lubrication and maintenance
www.nov.com
Magnetic Particle InspectionAnnual inspection (power slip in use)
Non-destructive examination
NOV power slips should be MPI examined according to the maintenance procedures. This magnetic particle examination should be conducted as outlined in the latest revision of the recommended practice API RP 8B as a minimum. The magnetic particle examination method consists of magnetizing the area to be inspected and then applying magnetic particles to the surface of the test area.
Evaluations of indications
Relevant indications: Only those indications with major dimensions greater than 1/16 Inch (1.6 mm) and associated with a surface rupture shall be considered relevant. Relevant indications are indications that results from, discontinuities within the test part. Non relevant indications are indications that results from excessive magnetizing current, structural design or permeability variances within the test parts.
Any indication believed to be non-relevant shall be regarded as relevant and shall be re-examined to determine whether an actual defect exists.
Linear indications shall be considered as those having a length of more than three times the width. Rounded indications shall be considered as those having a length less than three times the width. A lined indication shall be considered as a group of three more indications which touch an imaginary straight line connecting any two of the group.
For equipment delivered in accordance with API 8A & 8C PSL 1
Annual Inspection.1. Clean the surface from oil, grease, sand, paint and loose rust which may interfere with
satisfactory inspection.2. Carry out MPI according to ASTM E709, determine the type of defects and the degree by
comparing defects to ASTM E125 reference photographs to NOV acceptance criteria. 3. Review the found defects and determine acceptability as per tables below4. Examinations must be performed according to the continuous method, with sufficient
overlap to ensure 100% coverage of the area or part under inspection.
Type Discontinuity description
Max. degree criti-cal areas
Max. degree non-critical areas
I Hot tears, cracks None Degree 1II Shrinkage Degree 2 Degree 2III Inclusions Degree 2 Degree 2
IV Internal chills and chap-lets Degree 1 Degree 1
V Porosity Degree 1 Degree 2
-
Document number 50000845-MAN-001Revision APage 24 of 50
3: Lubrication and maintenance
www.nov.com
For equipment delivered in accordance with API 8C PSL 2
Tests
(Paper) slip test procedureSee TSEL-0158
Shop repairsChanging dies/inserts
Procedure
1. Remove the retaining pins by taking out the cotter pin
2. A die slot conditioner and die driver can be used to drive the dies out and recondition the die slots.
3. After replacing the inserts, the retaining pins with the cotter pins shall be reinstalled.
Type Discontinuity description
Max. degree criti-cal areas
Max. degree non-critical areas
I Hot tears, cracks None NoneII Shrinkage None Degree 1III Inclusions Degree 1 Degree 2
IV Internal chills and chap-lets None Degree 1
V Porosity Degree 1 Degree 2
NOTE: Only a NOV facility or an authorized repair facility is allowed to remanufacture PS15/16s which have indications outside the acceptance criteria.
WARNING: Only original Varco BJ parts must be used. PS15/16s are produced from cast alloy heat treated steel and must not be welded in the field. Improper welding can cause cracks and brittleness in heat-affected areas which can result in dramatic weakening of the part and possible failure. Repairs involving welding and/or machining should be performed only by an Varco BJ authorized repair facility. Using a PS15/16 that has been improperly welded or repaired is dangerous.
CAUTION: Wear eye protection when removing or replacing inserts to protect against chip fragments
-
Document number 50000845-MAN-001Revision APage 25 of 50
4: Installation and commissioning
www.nov.com
Installation and commissioningPre-installation check list PS15/16
Installation PS15/16
Check that slip and slip inserts match drill pipe size in use.
Check that the installed guide ring is correct for the size of drill pipe in use. Guide rings can be identified by looking at the figure stamped on the end section of the two halves. (Figure 7).
Figure 7. Guide ring identification and measurement
The following installation procedures assume that all pre-installation planning and rig up has been accomplished prior to PS15/16 installation. This includes:A Varco pin drive master bushing is installed in accordance with Varco specifications and any bushing insert has been removed.PS16 only: Rig 100 to 150 psi air has been piped in, flushed clean, and pressure tested. The size of drill pipe to be used in rig operation has been determined.
Procedure
NOTE: The slip size (4-1/2" or 5-1/2") is stamped on the side of the upper slip body. The insert P/N is stamped on back of slip insert. A B stamped on the insert after the P/N indicates a beveled edge insert for use on either the top or bottom of the slip dovetail slot.
NOTE: An undersize guide ring can interfere with the tool joints causing severe equipment failure. An oversize guide ring cannot center pipe and tool joints can catch and accidentally set slips, resulting in severe damage.
I.D.measured here
Matchinghalf identification
stamped here
End stamplocated here
-
Document number 50000845-MAN-001Revision APage 26 of 50
4: Installation and commissioning
www.nov.com
Installation PS16 control system
Connect filter/regulator and lubricator assembly to the rig air standpipe. Set the regulator to 90 psi. Locate and mount the inline pilot operated valve and pipe in to the filter/regulator. Note
that the inline valve must be mounted within the 23' reach of the two hoses supplied with the PS16.
Mount the hand operated pilot valve and pipe in 1/4" tubing from the lubricator output to the valve inlet.
Route 1/4" tubing from the hand operated valve to the pilot inlet of the inline valve. Hoist the PS16 onto the rig floor near the rotary table.
Lubricate the power slips per the Lubrication section. Connect the two air hoses provided from the inline valve to the PS16 and check power slip
operation by operating the hand valve several times. Take a strain on the drill string, if any, and remove the slips currently in use. Raise the PS16 off of the rig floor and open the bowl assembly. Guide the power slips around the drill string, if any, and lower into the master bushing
(Figure 8).
Operate the control valve to SET and slowly lower the drill string to set slips.
Procedure
NOTE: The PS16 weighs approximately 1,600 lb (725 kg)
NOTE: To prevent the power slips from pulling out of the master bushing during operation, lock in the power slips with the master bushing pins.
-
Document number 50000845-MAN-001Revision APage 27 of 50
4: Installation and commissioning
www.nov.com
Figure 8. PS16 installation
Check out procedure PS15/16
PS16 only: Check that the hand control pilot valve is in the SET position and latched. PS16 only: Check the system for air leaks. Repair as required. Put a strain on the drill string. Unlatch and operate the PS15/16 to the slip RELEASE position. The PS15/16 top cover
should rise releasing the slips from the drill string. PS16 only: Check that the air cylinder rods are at the top of their travel. Operate the control valve to the SET position and slowly lower the drill string to set the
slips. Check that the drill pipe is gripped evenly by the PS15/16 slips. If any problems are noted during the above procedure, troubleshoot the system using the
fault finding procedures included in this manual.
Procedure
VarcoPin drivemaster bushing
Drill string
-
Document number 50000845-MAN-001Revision APage 28 of 50
4: Installation and commissioning
www.nov.com
-
Document number 50000845-MAN-001Revision APage 29 of 50
5: Operation
www.nov.com
OperationsLifting the PS15/16PS16
Use a 4-way lifting spring with a SWL (safe working load) for min. 1,600 lb (727.3 kg) Attach the 4 hooks to the holes as shown in the picture Lift the PS16
PS15
Attach any lifting devices to the holes in the top cover Lift the PS15
Procedure
CAUTION: When lifting, the cylinders may extract.
Procedure
WARNING: Do not attach any lifting device to the setting ring of the top cover.
-
Document number 50000845-MAN-001Revision APage 30 of 50
5: Operation
www.nov.com
Operation PS15
1. The slips are set by stepping on the step rail on the outside of the cover
2. The slips are held set by the drill pipe weight and the latch with latch lock serves as a safety if the driller was to pick up the accidentally on the drill pipe, but didnt want the slips to come up.
3. To allow the slips to come up, step on the latch-lock-pedal.
Theory of operation PS16When the hand-operated pilot control valve is operated to the SET position, the 90 psi pilot air stream is removed from the inline valve. This allows the spring-loaded internal valves to direct 90 psi air from the filter/regulator through the low pressure hoses to operate the check valve located on the PS16 (Figure 6).Releasing the check valve exhausts air from the bottom of the air cylinders through the inline valve to the atmosphere.
Taking a strain on the drill string and moving the hand control to the RELEASE position directs a 90 psi air stream to the inline valve operating internal valves, directing air from the filter/regula-tor to the bottom of the air cylinders located on the PS16. This air pressure extends the cylinder rods, raising the top cover and attached slips, releasing the drill pipe.
Procedure
CAUTION: Make sure down far enough to go past the latch cover.
WARNING: Ensure the pipe has stalled prior to setting the slips.
NOTE: Ensure there is sufficient weight before using the PS, e.g. after the bottom hole and heavy weight has been run.
WARNING: Power slips should be left in the locked or SET position while supporting pipe or casing and not released until secondary support of the string is in place. Under certain conditions, e.g., very light loads, releasing the slips before picking up the load can result in a dropped string.
WARNING: Do not use the 6-5/8" power slips as anything other than a tripping tool. Severe damage can result when drilling ahead using 6-5/8" pipe and the PS16.
-
Document number 50000845-MAN-001Revision APage 31 of 50
5: Operation
www.nov.com
Setting the power slips
Take a strain on the drill string. Unlatch and operate the hand control pilot valve to the SET position. Slowly lower the drill string to automatically set the slips.
Releasing power slips
Take a strain on the drill string. Unlatch the hand control pilot valve and move the control handle to the RELEASE
position. The PS16 top cover rises, releasing the slips (Figure 9).
Figure 9. PS16 operation
Procedure
Procedure
26(660)
Slipreleased
32(813)
17.5(445)
Slipset
32(813)
Varco pin drivemaster bushing
-
Document number 50000845-MAN-001Revision APage 32 of 50
5: Operation
www.nov.com
Procedure changing PS16 slips
The safety clamp is a back-up for the inline operated operated check valve.Normally, the check valve blocks the trapped air when slips are in the UP-position. In case of any internal leakage due to wear or tear the slips may be sagging, resulting in a possible dangerous situation.
CAUTION: When changing the slips, use the safety clamp which will prevent the slips to sag when disconnecting the air supply.
Safety clamp open position
Safety clamp
-
Document number 50000845-MAN-001Revision APage 33 of 50
6: Assembly
www.nov.com
Assembly and dis-assemblySafety
Procedure prior to working on the PS16 or any of its parts
If the PS is connected to a power unit, bleed the system prior to repair.
To bleed the PS;
1. Shut the valve in the Pressure line2. Shut off the power unit3. Give command and a number of times
Before (dis)assembly of the PS make sure:1. All tools are at hand2. Hoisting equipment is available3. Lifting equipment is suitable for handling heavy parts (crane, lifting straps, chains, eyes
etc)Torques
Use the proper torque for assembly parts. Applying too much torque easily could damage cartridges.
Required tools
For normal maintenance and repair, standard tools will be sufficient for all work. However, bigger size spanners may be required for hydraulic tubes
Special tools
No special tools are needed.
NOTE: Use the drawings for reference
WARNING: Make sure that all pneumatic lines are isolated before any work is performed on the PS.
WARNING: When working on the PS, lock and tag the controls in order to prevent unexpected movement of the PS.
WARNING: Do not weld on PS or individual parts
NOTE: Prior to assembly or disassembly, clean the PS thoroughly with a steam-cleaner in order to prevent the parts from getting contaminated with dirt, mud etc.
-
Document number 50000845-MAN-001Revision APage 34 of 50
6: Assembly
www.nov.com
-
Document number 50000845-MAN-001Revision APage 35 of 50
7: Trouble shooting
www.nov.com
Trouble shooting Troubleshooting information is provided in the following table. Proper correction procedures, or references to procedures contained in the Maintenance or Installation sections of this manual, are detailed in the solution column of the table.
When problems cannot be solved, contact an authorized Varco repair facility
Overview possible problems
Symptom Probable cause Remedy
Slips sticking on release Insufficient lubricationLubricate slip bodies and grease fittings with EP grease per Lubrication section.
Slips do not release Insufficient strain taken Take a strain on the drill string. on drill string.
PS16 only: Low or no air pressure.
Check hoses to and frominline valve for crimping or obstruction; remove.Check pressure setting on filter/regulator. Readjust to 90 psi, if necessary.
If no pressure, check filter and clean and replace.
Slips do not release. PS16 only: No output from control pilot valve.
Check that 1/4" tubing to and from control valve is not crimped or crushed. Replace, if necessary.
PS16 only: No output from inline valve.
Check for air pressure from valve. Clean and/or replace, if necessary.
Slips do not set. Dirty or dry slips or bowl. Clean and lubricate per Lubrication section.PS16 only: No air pressure from inline valve to operate check valve.
Check hoses to and from inline valve for crimping or obstructionremove.Check output from inline valve. Clean and/or replace, if necessary.
PS16 only: Air from cylinders not exhausting through check valve.
Clean or replace check valve.
Slips do not grip pipe. Dirty slip inserts. Clean slip inserts.
Worn inserts Replace inserts per Maintenance section.
Worn slip assembly(s) Replace slip assembly(s) per Maintenance section.Pipe or tool joints catching on slip segments during operation.
Worn or oversize guide ring. Measure and/or replace guide ring per Maintenance section.
Bowl hinge pin worn.Pull slips and check hinge pin for wear. Replace, if necessary.
-
Document number 50000845-MAN-001Revision APage 36 of 50
7: Trouble shooting
www.nov.com
-
Document number 50000845-MAN-001Revision APage 37 of 50
8: Appendixes
www.nov.com
AppendixATEX
Over a limited period the temperature of the PS16 was measured while it was running on the test bench with exaggerated cycle speed. A normal cycle would take about 3 minutes, while during the test there was a continuous cycling for 20 cycles raising and setting the slips 10 times.
Conclusion:
The maximum temperature measured was decreasing, also compared to the ambient temperature.
The tool will be classified as CE Ex IIG2 T5 (temperature class 100 C).
6567
6971
7375
7779
8183
85
1 3 5 7 9 11 13 15 17 19
Number of cycles
Temperature F
1. Cylinder rod side
2. Cylinder piston side
4. Connector coupling, outlet
3. Connector coupling, inlet
-
Document number 50000845-MAN-001Revision APage 38 of 50
8: Appendixes
www.nov.com
Storage, transport & scrapping.The following sections detail proper disassembly of the tool to comply with various environmental requirements.
Storage
When the PS is not being used for a longer period then 3 days the following steps should be carried out:
1. Remove the slip assembly.2. Clean PS slip assembly.3. Grease PS and slip assembly as described in checklist lubrication.4. Place PS in closed position.5. Grease all blank parts.6. Use an extreme pressure, multi-purpose, lithium based grease of No. 1 or No. 2
consistency and multi grade motor oil.7. Grease trigger finger-shaft.8. Clean and cap Quick Disconnect Couplings.
Transport1. Lift the PS by the lifting eyes only.2. The best way of transporting the PS is in its original crate. Use oiled paper and seal the
box with plastic from leaking when stored outside. Secure the top.Scrapping
1. The tool contains, grease, aluminium, steel, rubbers, plastic and several assembled components from undefined consistency or mixtures. The tool can be contaminated with mud.
2. When the tool is taken out of service it is recommended to disassemble the tool in a place where drainage for waste fluids is possible.
3. Mud and grease are unsafe when touched by the skin. Always wear gloves and safety goggles when disassembly the tool.
4. Remove all quick-disconnects, hoses, cylinders and manifold blocks.5. Clean the tool with a steam cleaner.6. Carry of to proper place for final storage or destruction.
Lubrication before storage
Apply grease to all grease points according to the chapter Maintenance, prior to storage of the tool.
CAUTION: Mud and grease are unsafe when touched by the skin. Always wear gloves and safety goggles when disassembling the tool.
-
Document number 50000845-MAN-001Revision APage 39 of 50
8: Appendixes
www.nov.com
Torque values (US)
Tensile Strength = 150,000 psi to 1 dia. Proof Strength = 120,000 psi
Tensile Strength = 150,000 psi to 1 dia. Proof Strength = 120,000 psi
Bolts Lubricated with Light Machine Oil
Bolts lubricated with Anti-seize compound
Grade 8 Grade 8
Dia. Threads per inch
Min. Torque(ft lb)
Max.Torque(ft lb)
Clamp force(lb)
Min. Torque(ft lb)
Max.Torque(ft lb)
Clamp force(lb)
Coarse Thread Series, UNC1/4 20 11.4 12.6 2860 8.6 9.5 28605/16 18 24 26 3720 17.8 19.7 37203/8 16 43 47 7000 32 35 70007/16 14 67 74 9550 50 55 95501/2 13 105 116 12750 78 87 127509/16 12 143 158 16100 107 118 161005/8 11 209 231 20350 157 173 203503/4 10 361 399 30100 271 299 301007/8 9 570 630 41600 428 473 416001 8 855 945 54500 641 709 544001 1/8 7 1216 1344 68700 912 1008 687001 1/4 7 1729 1911 87200 1297 1433 872001 3/8 6 2261 2499 104000 1696 1874 1040001 1/2 6 3002 3318 126500 2252 2489 126500
Bolts Lubricated with Light Machine Oil
Bolts lubricated with Anti-seize compound
Grade 8 Grade 8
Dia. Threads per inch
Min. Torque(ft lb)
Max.Torque(ft lb)
Clamp force(lb)
Min. Torque(ft lb)
Max.Torque(ft lb)
Clamp force(lb)
Fine Thread Series, UNF1/4 28 13.3189 14.7 3280 10 11 32805/16 24 24 26 5220 17.8 19.7 52203/8 24 48 53 7900 36 39 79007/16 20 76 84 10700 57 63 107001/2 20 114 126 14400 86 95 144009/16 18 162 179 18250 121 134 182505/8 18 228 252 23000 171 189 230003/4 16 399 441 33600 299 331 336007/8 14 627 693 45800 470 520 458001 14 950 1050 59700 713 788 597001 1/8 12 1368 1512 77000 1026 1134 770001 1/4 12 1900 2100 96600 1425 1565 966001 3/8 12 2584 2856 118400 1938 2142 1184001 1/2 12 3382 3738 142200 2537 2804 142200
-
Document number 50000845-MAN-001Revision APage 40 of 50
8: Appendixes
www.nov.com
Torque values (metric)Bolts Lubricated with Light Machine Oil
Bolts lubricated with Anti-seize compound
Grade 8 Grade 8
Diameter
Threads per inch
Min. Torque(Nm)
Max.Torque(Nm)
Clamp force(N)
Min. Torque(Nm)
Max.Torque(Nm)
Clamp force(N)
Coarse Thread Series, UNC1/4 20 15.5 17.14 12870 11.7 12.9 128705/16 18 32.6 35.4 16740 24.2 26.8 167403/8 16 58.5 64 32500 43.5 47.6 315007/16 14 91.1 100.6 42980 68 92.5 429801/2 13 143 158 57380 106 118 573809/16 12 195 215 72450 145.5 160 724505/8 11 284 314 91580 213.5 235 915803/4 10 491 542 135450 368 407 1354507/8 9 775 857 187200 582 643 1872001 8 1163 1285 245250 872 965 2452501 1/8 7 1654 1828 309150 1240 1370 3091501 1/4 7 2351 2598 382400 1764 1949 3924001 3/8 6 3075 3398 468000 2306 2549 4680001 1/2 6 4082 4512 569250 3062 3385 569250
Bolts Lubricated with Light Machine Oil
Bolts lubricated with Anti-seize compound
Grade 8 Grade 8
Diameter
Threads per inch
Min. Torque(Nm)
Max.Torque(Nm)
Clamp force(N)
Min. Torque(Nm)
Max.Torque(Nm)
Clamp force(N)
Fine Thread Series, UNF1/4 28 18.1 20 14760 13.6 15 147605/16 24 32.6 35 23490 24.2 26.8 234903/8 24 65.3 72 35550 49 53 355507/16 20 103 114 48150 77.5 86 481501/2 20 155 171 64800 117 129 648009/16 18 220 239 82130 165 182 821305/8 18 310 343 103500 232 257 1035003/4 16 542 600 151200 406 450 1512007/8 14 853 943 206100 639 707 2061001 14 1292 1428 268650 970 1071 2686501 1/8 12 1860 2056 346500 1396 1542 3465001 1/4 12 2584 2856 434700 1938 2128 4347001 3/8 12 3514 3884 532800 2635 2913 5328001 1/2 12 4599 5083 639900 3450 3813 639900
-
Document number 50000875-MAN-001Revision APage 41 of 50
9: Drawings
www.nov.com
Drawings & PartsPS15 main assembly
1
2
3
4 5
67
8
9
10
11
1213
14
16
21
22
2324
25
2627
28
29
29
31
32
33
34
2918
-
Document number 50000875-MAN-001Revision APage 42 of 50
9: Drawings
www.nov.com
* Part of spring cartridge Assembly PN 74623
**Part of Slip Assembly, see table for PN
Pos Partnumber Description Qty
1 51404-24 Pin, Cotter 12 18121 Pin, Hinge 13 74020 Nut, Torque* 44 51435-14 Pin, Cotter* 45 50914-C Lockwasher* 46 ? Lockwire A7 19123 Screw, Drilled* R4
8 50810-N-C-5 Washer, Flat* 4
9 72836 Cover, Top 110 50006-5-C5 Screw, Hex-hd 411 50906-C Lockwasher 412 19818 Plate, Retainer 213 19825 Seal, Wiper 4
14 74623 Spring Cartridge Assy 4
15 19819 Bushing, Cartridge 416 51402-10 Pin, Cotter 117 17173 Pin, Latch 118 18286-1 Spring, Latch Rh 119 18286 Spring, Latch Lh 1
20 200220 Latch, modified, see next image 1
21 51404-12 Pin, Cotter 422 75653 Pin, Up Slip hanger 423 7760 Hanger, slip** 424 19856 Pin, Low Slip Hanger** 4
25 51403-12 Pin, Cotter ** 8
26 50008-32-S Screw, Hex-hd 427 50908-C Lockwasher 428 53201 Grease Fitting 429 18191 Bowl Set 130 See Table Bottom Guide Set 131 See Table Slip Set 132 See Table Insert Set** 133 50108-6-S Screw, Socket-hd** 834 51108 Lockwasher** 8
-
Document number 50000875-MAN-001Revision APage 43 of 50
9: Drawings
www.nov.com
Modified latch and lock assy PN 200220
Pos Partnumber Description Qty
01 200221 Topplate indicator 102 200222 Pin 103 939534-4 Eye bolt 204 200223 Modified latch 105 939248-4 Nut 206 200224 Adjustment nut 207 200225 Foot pedal 1
08 32482 Torsion spring 1
09 200227 Pin 110 200228 Cam plate 211 200229 Latch pin 112 939672-16 Cotter pin 513 939672-18 Cotter pin 1
14 939672-27 Cotter pin 1
15 18286-1 Spring, Latch right 116 18286-2 Spring, Latch left 117 50812-R-S Washer, regular 118 200226 Work instructions drawing 1
-
Document number 50000875-MAN-001Revision APage 44 of 50
9: Drawings
www.nov.com
PS16 drawing numbers
PS16 Parts
Drawing No. Name75942 PS16 Assembly79195 PS16 Installation93283 Pilot Air Valve93360 PS16 pneumatic schematic79011 Guide set93515 Installation
8
.31
3
37
42
44
38
52
49
4527
9
47
2324
7
20
3950
53
14
4 Pl.
5
10
13
Outletport
4
29
1
48
25
18
21
225
11
32 19
4 Pl.
4 Pl.
42
Ref
Ref
Ref
4 Pl.
4 Pl.
Ref
29
6
4 Pl.
4 Pl.
Guide pins
2 Pl.
2 Pl.
2
Ref
8
4 Pl.
4 Pl.31
RefRef
4 Pl.
4 Pl.
View C - C
CC
-
Document number 50000875-MAN-001Revision APage 45 of 50
9: Drawings
www.nov.com
.15 2Pl.
9
27
2
51
13
3716
1115
3433
17
18
41
3
12
28
3 3511
37
45
46
43
36
51
Ref
Ref
RefRef
-
Document number 50000875-MAN-001Revision APage 46 of 50
9: Drawings
www.nov.com
Table 1; PS16 Parts list
Item. No. Description Part number Qty.1 Bowl 77097 12 Top cover 79426 13 Hose guard 77128 14 Guide bushing 19819 4 5 Retainer plate 19818 2 6 Guide pin 77101 4 7 Thrust washer 77122 2
8 Socket-hd. drilled screw
77155 4
9 Hanger pin 75653 4 10 Wiper ring seal 19825 4 11 Air cylinder 77133 2 12 Bowl hinge pin 18121 1
13 Relief valve side outlet 89458 1
14 Torque nut - 250 ft lb 74020 4
15 90 Elbow, ext pipe 56506-12-8-S 2 16 Plug, ext pipe 53000-12-S 1 17 Cap screw, hex-hd. 50008-12-C5 8 18 Flat washer 50808-N-C 8
19 Lock washer, hi-collar 51112-C 4
20 Roll pin 51604-14 2 21 Cap screw, hex-hd. 50006-5-C5 4 22 Lock washer, reg . 50906-C 4 23 Flat washer 79143 2 24 Cap screw, hex-hd. 50016-18-C5 2 25 Cap screw, hex-hd. 50008-32-S 4 26 Grease fitting 53201 4 27 Cotter pin 51404-12 4 28 Cotter pin 51404-24 1
29 Grease, severe service 56003 A/R
30 Never seez 19709 A/R 31 Hex nut, slotted 50512-C 4 32 Cotter pin 51402-12 4 33 Hose assembly 58624P230037 1 34 Hose assembly 58624P230057 1 35 Connector, ext pipe 56501-12-8-S 2
36 Valved nipple, Q/D ext pipe 7735 1
37 Pipe reducer ext/int 56700-12-8-S 1
38 Valved coupler, Q/D ext pipe 7843 1
39 Lock washer, reg. 50914-C 4 40 Street elbow 56702-8-8-S 1 41 Lock washer 50908-C 8
-
Document number 50000875-MAN-001Revision APage 47 of 50
9: Drawings
www.nov.com
Table 1; PS16 Parts list (cont.)
Figure 14
Item. No. Description Part number Qty.42 Dust plug, Q/D 55914-8 143 Dust cap, Q/D 55915-8 1
44 Check valve, pilot operated 80401 1
45 Elbow, 1/2" 56506-8-4-S 146 Tee 56162-8-8-S 147 Slip assembly See Figure 5 448 Guide ring See Table 1 149 Tube 80381 150 Stud 86818 4
51 Cover assembly check valve 80380 2
52 Elbow 56506-4-4-S 153 Roll pin 51603-16 4
90
Handle
Latch
10
63 2 1
7
Ref
5
4
PS-16
POS 2POS 1
-
Document number 50000875-MAN-001Revision APage 48 of 50
9: Drawings
www.nov.com
Control system parts list
Item. No. Description Part number Qty.
1 Close nipple 53908-B 12 Lubricator assembly 11836 13 Male pipe nipple, Q/D 7735 24 Hose assembly, 23 ft 11814 25 Male pipe coupler, Q/D 7843 26 Inline valve, pilot operated 93284 17 Filter-regulator 11883 18 Elbow 90 - int. pipe 56707-8-8-S 29 Pipe nipple 52008-24-G 1
10 Hand control pilot valve 93283 1
-
Document number 50000875-MAN-001Revision APage 49 of 50
9: Drawings
www.nov.com
Figure 15; slip assembly and parts list
Figure 15
Drill pipe Slip assy Slip body Insert
size P/N P/N Size P/N Qty
3-1/2" 7686 7682 4-1/2" 2163 82163B 4
4" 7685 7682 4-1/2" 2164 82164B 4
4-1/2" 7684 7682 4-1/2" 2165 124-1/2" 7691 7687 5-1/2" 2168 8
2168B 45" 7690 7687 5-1/2" 2169 8
2169B 45-1/2" 7689 7687 5-1/2" 2170 126-5/8" 7696-A 6-5/8" 2632-68-12 18
-
Document number 50000875-MAN-001Revision APage 50 of 50
9: Drawings
www.nov.com
top related