pocket customer.) clip instructions 08u25-s3v-2f00-91 accessory application publications no. issue...
Post on 16-Mar-2018
215 Views
Preview:
TRANSCRIPT
© 2005 American Honda Motor Co., Inc. - All Rights Reserved. BII 30961 (0509) 1 of 3
INSTALLATIONINSTRUCTIONS
08U25-S3V-2F00-91
Accessory Application Publications No.
Issue Date
CIGARETTE LIGHTERAND ASHTRAY
TOURING PACKAGETOURING PACKAGE NAVI SEP 2005
Cigarette lighter
Wire tie
Ashtray (sold separately):P/N 08U25-S3V-210 (Black)P/N 08U25-S3V-270 (Saddle)P/N 08U25-S3V-221 (Quartz)
Ashtray
INSTALLATION
1. Move the shift lever to the N position, thenremove the pocket. Save the pocket for yourcustomer.
3 Cushion tapes
2. Remove the center lower cover by releasing the fourclips and two tabs. Take care not to damage theclips.
3. Make sure you have the anti-theft code for the radioand, if equipped, the navigation system, then writedown the radio station presets.
4. Disconnect the negative cable from the battery.
2006 MDXWITHOUT REAR
ENTERTAINMENT SYSTEM
If you’re installing only an ashtray, go to step 21;otherwise continue with step 2.
BII 30961
POCKET(Save for yourcustomer.)
CLIP
CENTER LOWERCOVER
TOOLS AND SUPPLIES REQUIRED#2 Phillips screwdriverStubby Phillips screwdriverElectrical tape
PARTS LIST
Cigarette Lighter (sold separately):P/N 08U25-S9V-100B
Harness
User's Guide
2 of 3 BII 30961 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
5. Open the accessory socket protector, and removethe four screws securing the front console.
6. Remove the clip of the accessory socket harnessfrom the front console, unplug the accessorysocket connector, and remove the front console.
7. Locate the 4-pin connector blue taped to thevehicle harness, and remove the tape to free theconnector.
8. Wrap electrical tape around the accessory socketconnector, and secure it to the vehicle harnesswith the wire tie.
9. Remove the accessory socket cover from theaccessory socket by turning it counterclockwise,then remove the accessory socket from theaccessory socket protector.
10. Separate the lighter cover from the cigarette lighter,then install them through the hole in the accessorysocket protector.
11. Remove the cover from the illumination light of theharness.
12. Connect the terminals of the harness to theterminals on the cigarette lighter; push theillumination light of the harness into the light holderon the front console.
13. Wrap the cushion tape around the harness.
CLIP
ACCESSORY SOCKETCONNECTOR
ACCESSORY SOCKETPROTECTOR
SELF-TAPPINGSCREWS
FRONTCONSOLE
CIGARETTELIGHTER CIGARETTE
LIGHTER COVER
ACCESSORYSOCKET COVER
ACCESSORYSOCKETPROTECTOR
ACCESSORYSOCKET
WIRE TIE
BLUE TAPE
4-PINCONNECTOR
ELECTRICALTAPE
CIGARETTELIGHTER
LIGHTHOLDER
Turnclockwise.
COVER(Discard.)
HARNESS
TERMINALS
FRONTCONSOLE
LIGHT
CLIP(Removeand discard.)
CUSHIONTAPE
© 2005 American Honda Motor Co., Inc. - All Rights Reserved. BII 30961 (0509) 3 of 3
14. Connect the 4-pin connector of the harness to the4-pin connector of the vehicle harness, and wrap thecushion tape around the connectors.
15. Reinstall the front console.
16. Reinstall all removed parts.
17. Reconnect the negative cable to the battery.
18. Check that the cigarette lighter heats properly whenpressed in.
19. Enter the customer’s radio and, if equipped, thenavigation system anti-theft codes, and reset theradio station preset buttons.
ASHTRAY
CUSHION TAPE
HARNESS
FRONTCONSOLE4-PIN
CONNECTORS
VEHICLEHARNESS
20. Reset the clock.21. Install the ashtray.
22. Open and close the ashtray several times to be surethat it works properly.
23. Give the pocket, and the User's Guide to yourcustomer.
top related