rogers group, inc.. rogers group history founded 1908, bloomington, indiana by ralph rogers grew...
Post on 19-Jan-2016
216 Views
Preview:
TRANSCRIPT
ROGERS GROUP, INC.
Rogers Group HistoryRogers Group HistoryRogers Group HistoryRogers Group History
Founded 1908, Bloomington, Indiana by Ralph Rogers
Grew with nation’s interstate system, infrastructure growth
Privately held by Ralph Rogers’ descendants
Rogers Group, Inc Rogers Group, Inc
• Sixth largest crushed stone producer in the US • Operations in five states: IN, KY, TN, AL, AR• 1600 employees• Core businesses - crushed stone, asphalt & asphalt
construction• Other businesses - block & masonry• Annual sales - $350,000,000
Maintenance and Maintenance and GuardingGuardingProgramsPrograms
““Effective Guarding”Effective Guarding”
““Why do we need guards?”Why do we need guards?”
Standard 56/57 .14107 (a) Standard 56/57 .14107 (a) Specifies:Specifies:
Moving machine parts shall be guarded to protect persons from contacting gears, sprockets, chains, drive, head, tail and takeup pulleys, flywheels, couplings, shafts, fan blades, and similar moving parts that can cause injury.
Guards shall not be required where the exposed moving parts are at least seven feet away from walking or working surfaces.
An Effective Machine An Effective Machine Guard Should:Guard Should:
Be considered a permanent part of the machine or equipment.
Afford optimum protection.Prevent access to the danger zone
during operation.
Be designed for the specific job and specific machine, with provisions made for oiling, inspecting, adjusting and repairing machine parts.
Be durable and constructed strongly enough to resist normal wear.
Not present a hazard in itself.
Moving MachineryMoving Machinery
Protective guards placed around moving machinery should be positioned so that the moving equipment does not present a hazard.
What is wrong in this picture?What is wrong in this picture?
Other Options for Other Options for ConveyorsConveyors
Stop CordsStop Cords
Must be located so that it can be reached by a person who falls on or against the belt.
Must be sufficiently taut to assure the conveyor drive motor will be deenergized when the cord is pulled.
RailingRailingA railing can be installed along the conveyor
instead of a stop cord.The railing must be placed away from and
slightly above the belt to prevent contact with the moving belt.
In cases where cables are used for railings, they must be kept tight and free of burrs.
Takeup PulleyTakeup Pulley
The moving machine parts of takeup pulleys are normally located a sufficient distance above the ground to be “guarded by location.”
Suspended ConveyorSuspended ConveyorA suspended conveyor with
the guides blocked by a bar to prevent the counterweight from dropping to ground level in case of belt breakage.
For additional safety, cables are fastened to the structure.
When stop bars and When stop bars and adequate cables are adequate cables are utilized to prevent free fall utilized to prevent free fall of the counterweight, and of the counterweight, and the moving machine parts the moving machine parts are located a minimum of are located a minimum of seven feet above the seven feet above the ground, a guard is not ground, a guard is not required.required.
Guard MaintenanceGuard Maintenance
•Assignment of competent employees to inspect areas requiring guards.
•Establish a checklist of points to be inspected.
Inspections:
MobileMobileEquipmentEquipment
Guard MaintenanceGuard Maintenance
•Pre-operational inspection of equipment should include guards.
Inspections:
The Future?The Future?
Area Guarding
Area GuardArea Guard
Area GuardArea Guard
An advantage of the area guard is that it may be less expensive and provides easy access. A disadvantage is that both belts need to be locked-out and tagged-out before entering the guarded area.
The Future?The Future?
New Technology
New TechnologyNew TechnologyLaser Beams may be effective at long range. They can monitor area perimeters and detect when entry into a hazardous area occurs. Pulsed Infrared Light Curtain Systems may find use as area guards. They are particularly useful in dusty environments. Pressure Plates can be equipped with sensors that detect changes in a radio frequency field or electrical capacitance. They can guard an area by sensing a person’s approach through contact with the plate.
New TechnologyNew Technology
Mechanical Pressure Mats open electrical contacts to stop a motor when someone steps on the mat in a hazard area.
Interlock Systems are available with multiple contacts. Multiple contacts or zones can be used to trigger a warning alarm for entry into an area but shut a system down if the person continues past the warning and approaches a hazard too closely.
New TechnologyNew Technology
Does the system react quickly and at sufficient distance to prevent contact with the machine parts before their motion has stopped? Is the system redundant? Can it be easily by-passed, such as ducking under a laser beam? Is there regular and frequent testing?
Standard 56/57 .14107 (a) Standard 56/57 .14107 (a) Specifies:Specifies:
Moving machine parts shall be guarded to protect persons from contacting gears, sprockets, chains, drive, head, tail and takeup pulleys, flywheels, couplings, shafts, fan blades, and similar moving parts that can cause injury.
Guards shall not be required where the exposed moving parts are at least seven feet away from walking or working surfaces.
Questions?
top related