section 10 white motors, brakes & rotary flow dividers · white motors wm series page 10.01...
Post on 20-Jul-2020
11 Views
Preview:
TRANSCRIPT
Date: 2013
CROSS
SECTION 10White Motors, Brakes &
Rotary Flow Dividers
Make Model PageWhiteWhiteWhiteWhiteWhiteWhiteWhiteWhiteWhiteWhiteWhiteFluid PressWhiteDeltaDeltaMTE
WM Series MotorsWP Series MotorsRS Series MotorsWR Series MotorsWS Series MotorsRE Series MotorsDR Series MotorsHB Series MotorsDT Series MotorsD9 Series MotorsSB Series BrakesFlangeable ValvesFD Series Flow DividersP Series Flow DividersPM Series Flow DividersHSR Series Flow Dividers
10.0110.0210.0310.0410.0510.0610.0710.0810.0910.1010.1110.12~10.1410.1510.1610.1710.18
10
White MotorsWM Series
Date: 2013Page 10.01CROSS
CROSS
HOUSING
125
ROTOR SHAFT
AAAAA
Housings Code Add to List3 Hole, M6 Round, Side G 3/8 JKB
3 Hole, 1/4” Round, Side 9/16” UN JL5
3 Hole, M6 Round, End G 3/8 JMB
Output Shafts Code5/8” Parallel C3
16mm Parallel C4
16mm 9 Tooth Spline C5
10
Note: Flow and pressure are continuous operation.See catalogue for peak.
Stock No.Rotors (Displacement) RPM Max. Flow Max Pressure
List Pricecu.in/rev cc/rev per LPM lpm bar
125008*****AAAAA 0.5 8 118 20 140
125012*****AAAAA 0.8 13 77 20 140
125020*****AAAAA 1.2 20 50 20 140
125032*****AAAAA 1.9 32 32 20 140
125040*****AAAAA 2.5 40 25 20 140
125222001 Seal Kit
Light Duty Hydraulic MotorWM (125/126 Series)
JKB, JK5 - (3) M6 x 1, Min. Depth 10 [.394] JLB, JL5 - (3) 1/4-28 UNF, Min. Depth 10 [.394] Drain Port: JKB, JLB - (3) M6 x 1, Min. Depth 10 [.394]
JK5, JL5 - (3) 1/4-28 UNF, Min. Depth 10 [.394]
61 [2.40]Ø 45 [1.77]
Ø 60 [2.36]
45°
35 [1.378]
5 [.20]
A
12.2 [.478]
31.5 [1.240]31.4 [1.238]
15 [.60]
30 [1.20]
63 [2.48]
A
B
JKB G 3/83-HOLE, ROUND MOUNT, ALIGNED SIDE PORTS JL5JK5 9/16-18 UNF JLB G 3/8 9/16-18 UNF
HOUSINGS Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005].
White MotorsWP Series
Date: 2013Page 10.02CROSS
CROSS
Stock No.Rotors (Displacement) RPM Max. Flow Max Pressure
List Pricecu.in/rev cc/rev per LPM lpm bar
155025*****AAAAA 1.5 25 40 40 140
155032*****AAAAA 2.0 32 30 50 160
155040*****AAAAA 2.5 40 25 60 160
155050*****AAAAA 3.0 50 20 60 140
155060*****AAAAA 3.6 59 17 60 160
155080*****AAAAA 4.8 78 13 60 160
155100*****AAAAA 5.9 96 10 60 160
155125*****AAAAA 7.6 125 8 60 160
155160*****AAAAA 9.4 154 6 60 160
155200*****AAAAA 11.6 190 5 60 150
155250*****AAAAA 14.6 240 4 60 140
155315*****AAAAA 18.5 303 3 60 120
155400*****AAAAA 23.7 388 2.6 60 95
155222001 Seal Kit
HOUSING
155
ROTOR SHAFT
AAAAA
Housings Code Add to ListSAE A 2 Bolt 1/2” BSPP Offset Manifold A63
Square 4 Bolt 7/8” UN Aligned F31
Output Shafts Code1” Parallel 1/4” Key 10
25mm Parallel 8mm Key 12
6B Spline (1”) 02
13 Tooth Spline (7/8”) 01
10
Note: Flow and pressure are continuous operation.See catalogue for peak.
HOUSINGS Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005].
55 [2.17]
13.5 [.531]
102 [4.02]
106.4 [4.189]
131.9 [5.193] Max.
80.8 [3.181]Max. 90.8 [3.575] Max.
18 [.71]
36 [1.42]
D
18 [.71]
Ø 82.5 [3.248]
20 [.79]
20 [.79]
20 [.79]
20 [.79]
B
A
A13 - 3 [.120] A63 - 8 [.310]
A13 - 40 [1.58] A63 - 35 [1.38]
(4) M8 x 1.25, Min. Depth 12 [.47]
A13 G 1/22-HOLE, SAE A MOUNT, OFFSET MANIFOLD PORTS A63 G 1/2 (TP)
Light Duty Hydraulic MotorWP (155/156 Series)
White MotorsRS Series
Date: 2013Page 10.03CROSS
CROSS
Stock No.Rotors (Displacement) Rotor Width RPM
per LPMMax.Flow Max. Pressure
List Pricecu.in/rev cc/rev inches lpm bar
RS03****00 3.2 52 0.317 19.3 25 120
RS04****00 4.6 76 0.463 13.2 40 120
RS05****00 5.4 89 0.541 11.4 48 120
RS99****00 6.3 103 0.776 9.7 60 120
RS06****00 6.8 111 0.681 9.0 60 120
RS08****00 7.7 127 0.776 7.9 70 103
RS10****00 10.0 164 1.001 6.1 80 103
RS12****00 12.5 205 1.251 5.0 80 103
RS14****00 15.5 254 1.551 4.0 80 82
RS18****00 17.9 293 1.791 3.4 80 62
RS24****00 24.9 409 2.501 2.4 80 55
PS222001 Seal Kit
HousingsSAE ‘A’ Style & SAE ‘A’ Flange Code Add to List Price1/2” NPT (2 Hole Sae ‘A’ Style Mount)1/2” NPT (6 Hole Sae ‘A’ Style Mount)1/2” BSP.F Offset (2 Hole SAE ‘A’ Mount)1/2” BSP.F Offset Manifold (2 Hole SAE ‘A’ Mount)1/2” BSP.F O-Ring Aligned (2 Hole SAE’ A’ Mount)1/2” BSP.F Aligned (2 Hole SAE’ A’ Mount)7/8” O-Ring (2 Hole SAE ‘A’ Style Mount)7/8” O-Ring (2 Hole SAE ‘A’ Mount)7/8” O-Ring (6 Hole SAE ‘A’ Style Mount)Manifold (2 Hole SAE ‘A’ Style Mount)
03140709102004341106
Four Hole Square Mount
1/2” NPT1/2” BSP.F (With Metric Mount)7/8” O-RingManifold
01210205
Output Shafts1” Pinhole1” Straight1” Straight (For Speed Sensor Only)25mm Straight (7mm Key)25mm Straight (8mm Key)25mm Straight (For Speed Sensor Only)1” Tapered6B Spline (1” Dia)6B Spline Extended Nose (1” Dia)13 Tooth Spline (7/8”)
00012112082809061607
RotationClockwiseCounter Clockwise
01
OptionsNo OptionsPack Nut (1” Tapered Shaft Only)Milled Stator (Available On Manifold Housings Only)Free TurningIncreased Shaft/Housing Side ClearanceSpeed Sensor
0PBFIZ
ROTORHOUSING
OUTPUT ROTATION
OPTIONS
RS
10
White MotorsWR Series
Date: 2013Page 10.04CROSS
CROSS
Stock No.Rotors (Displacement) RPM Max. Flow Max Pressure
List Pricecu.in/rev cc/rev per LPM lpm bar
255040*****AAAAA 2.5 40 25 45 155
255060*****AAAAA 3.6 59 16 53 155
255070*****AAAAA 4.3 71 14 61 172
255090*****AAAAA 5.4 88 11 61 172
255100*****AAAAA 6.1 100 10 61 172
255115*****AAAAA 6.9 113 8 61 172
255130*****AAAAA 7.9 129 7.5 61 172
255160*****AAAAA 9.8 160 6 61 172
255200*****AAAAA 12.1 198 5 61 172
255240*****AAAAA 14.4 236 4 61 172
255320*****AAAAA 19.6 323 3 61 121
255400*****AAAAA 24.4 400 2.5 61 104
255222001 Seal Kit
HOUSING
255
ROTOR SHAFT
AAAAA
Housings Code Add to ListSAE A 2 Bolt 1/2” BSPP Offset Manifold A63
Square 4 Bolt 1/2” BSPP Offset Manifold F33
SAE B 2 bolt 1/2” BSPP Aligned B18
Output Shafts Code1” Parallel 1/4” Key 10
1” Tapered 13
25mm Parallel 8mm Key 12
6B Spline (1”) 04
13 Tooth Spline (7/8”) 01
10
Note: Flow and pressure are continuous operation.See catalogue for peak.
HOUSINGS Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005].
Dimension K is charted on page 10.61. (TP) - Taller Pilot Height. Refer to detailed drawing for dimensional differences. (Refer Catalogue)
130.3 [5.13]
Ø106.4 [4.19]
59 [2.34]51 [2.00]
Ø13.7 [.539]Ø13.5 [.531]
20 [.79] 20 [.79]
A1D - (4) 5/16-18 UNCA13, A63 - (4) M8 x 1.25
Min. Depth 13 [.50]
Ø82.5 [3.249]Ø82.3 [3.242]
36.1 [1.42]
A
B
18 [.71]
18 [.71]
Ø101.6 [4.00]
K
A13, A3D - 37 [1.48] A62 - 35 [1.38]
A13, A3D - 2.7 [.105] A62 - 5.2 [.205]
20 [.79]
20 [.79]
A13 G 1/22-HOLE, SAE A MOUNT, OFFSET MANIFOLD PORTS A1D 7/8-14 UNF A63 G 1/2 (TP)
For Light Duty ApplicationsWR (All Series)
White MotorsWS Series
Date: 2013Page 10.05CROSS
CROSS
Stock No.Rotors (Displacement) RPM Max. Flow Max Pressure
List Pricecu.in/rev cc/rev per LPM lpm bar
355100*****AAAAA 6.1 100 9.5 76 207
355110*****AAAAA 6.9 112 8.5 76 207
355130*****AAAAA 7.9 129 7.5 76 207
355160*****AAAAA 9.9 162 6 76 207
355200*****AAAAA 12.3 202 4.75 76 207
355230*****AAAAA 13.9 228 4.25 76 207
355320*****AAAAA 19.8 325 3 76 190
355400*****AAAAA 24.4 399 2.5 76 155
335500*****AAAAA 30.3 496 2 76 121
355355001 Seal Kit
HOUSING
355
ROTOR SHAFT
AAAAA
Housings Code Add to ListSAE A 2 Bolt (Side Ports) A7
SAE A 4 Bolt (Side Ports) AH
Wheel Mount 3.25” Spigot W8
Wheel Mount 4.25” Spigot Y8
Wheel Mount Euro 125mm Spigot Z8
Side Ports Code7/8” UN c/w 7/16” UN Drain 1
1/2” BSPP Offset Manifold 3
Output Shafts Code1” Parallel 1/4” Key 10
25mm Parallel 8mm Key 12
1-1/4” Parallel 8mm Key 20
6B Spline (1”) 02
14 Tooth Spline (1-1/4”) 23
35mm Tapered 28
32mm Parallel 10mm Key 21
1-1/2” Tapered 31
10
Note: Flow and pressure are continuous operation.See catalogue for peak.
White MotorsRE Series
Date: 2013Page 10.06CROSS
CROSS
Stock No.Rotors (Displacement) Rotor Width RPM
per LPMMax.Flow Max. Pressure
List Pricecu.in/rev cc/rev inches lpm bar
RE07****00 7.4 121 0.541 8.2 45 210
RE10****00 9.9 162 0.541 6.2 64 210
RE12****00 12.4 204 0.681 4.9 76 210
RE14****00 14.2 232 0.777 4.3 76 210
RE16****00 15.9 261 0.872 3.8 95 210
RE18****00 18.3 300 1.001 3.3 95 210
RE20****00 21.2 348 1.552 2.9 95 210
RE24****00 22.8 375 1.251 2.7 95 210
RE26****00 28.3 465 1.552 2.2 95 175
RE32****00 32.7 536 1.791 1.9 95 140
RE45****00 45.6 748 2.501 1.3 95 105
PE444001 Seal Kit
Housings7/8” O-Ring Ports 1/2” BSP.F Ports
Standard Relief Port Standard Relief PortSAE ‘A’ Style Flange (2 Hole Mount)SAE ‘A’ Style Flange (4 Hole Mount)SAE ‘A’ Style Flange (6 Hole Mount)Setback Flange (Wheel Motor) SetbackFlange (Wheel Motor With Brake Mount)72mm Setback Flange (Wheel Motor)125mm 6-bolt (Uses #08 Shaft Only)1.5” Shaft Wheel Motor (Uses #30 Or #31 Shaft Only)
1608180711091020
-384837-
39-
50
17061905-
14-
21
-364935-
44--
Output Shafts ‘A’ Style & Setback 72mm Setback1-1/4” Tapered1-1/4” Straight1” Straight1” Extended Nose Straight25mm Straight (8mm Key)32mm Straight6B Spline (1” Dia)12 Tooth Spline ( 1” Dia)13 Tooth Spline (7/8” Dia)14 Tooth Spline (1-1/4” Dia)15 Tooth Spline (1” Dia)19 Tooth Spline (1-1/4” Dia)
030406130709021832051108
101421--
1719-
2016-
15
1.5 Setback1-1/2” Straight (#20 & #21 Housing Only)1-1/2” Tapered (#20 & #21 Housing Only)
3031
RotationClockwiseCounter Clockwise
01
OptionsNo OptionsDeclutchWarn Hub (For #10 Housing And #08 Shaft Only)3000 PSI Relief Valve Installed (Relief Port Housings Only)Free TurningPack Nut (1-1/4” Tapered Shaft Only)Speed Sensor (Single)Speed Sensor (Dual) - Consult Cross For Availability
0JWR3FPZQ
ROTORHOUSING
OUTPUT ROTATION
OPTIONS
RE
10
White MotorsDR Series
Date: 2013Page 10.07CROSS
CROSS
Stock No.Rotors (Displacement) Rotor Width RPM
per LPMMax.Flow Max. Pressure
List Pricecu.in/rev cc/rev inches lpm bar
DR12****50 12.0 204 0.69 4.2 114 210
DR16****50 15.9 261 0.872 3.8 127 210
DR19****50 18.3 300 1.001 3.3 135 210
DR21****50 21.2 348 1.55 3.0 135 210
DR25****50 22.8 375 1.251 2.7 135 210
DR27****50 28.3 465 1.552 2.2 150 175
DR33****50 32.7 536 1.791 1.9 150 140
DR46****50 45.6 748 2.501 1.3 150 105
600555000 Seal Kit
Housings Code Add to List Brake Code Add To ListSAE ‘A’ Style Flange (2 Hole Mount)SAE ‘A’ Style Flange (4 Hole Mount)SAE ‘A’ Style Flange (6 Hole Mount)Setback Flange (Wheel Motor)Setback Flange (Wheel Motor With Brake Mount)72mm Setback Flange (Wheel Motor)125mm 6-Bolt (Uses #08 Shaft Only)Brake, 7.115 Dia Pilot (Uses #53 Shaft Only)
16081807110910-
-------
37
Output Shafts ‘A’ Style & Setback 72 mm Brake1-1/4” Tapered1-1/4” Straight1” Straight1” Extended Nose Straight6B Spline (1” Dia)12 Tooth Spline ( 1” Dia)13 Tooth Spline (7/8” Dia)14 Tooth Spline (1-1/4” Dia)15 Tooth Spline (1” Dia)19 Tooth Spline (1-1/4” Dia)25mm Straight (7mm Key)32mm Straight1-1/2” Tapered (For #37 Housings Only)
030406130218320511080709-
101421-
19-
2016-
15-
17-
------------
53
End CoverManifold Ports, D-Shaped1-1/16-12 UN-2B O-Ring Ports, Round1-1/16-12 UN-2B O-Ring Ports, D-Shaped3/4-14 BSP.F Ports, Round3/4-14 BSP.F Ports, D-Shaped7/8 O-Ring Rear Ports, Round
358790
OptionsNo OptionsWarn Hub (For #10 Housing And #08 Shaft Only)Relief Valve End Cover (#5 & #7 End Covers Only)3000 PSI Relief Valve InstalledShuttle Valve (#3, #5 & #7 End Covers Only)Free TurningPack Nut (1-1/4” Tapered Shaft Only)Speed Sensor (Single)Speed Sensor (Dual) - Consult Cross For Availability
0WR
R3DFPZQ
ROTORHOUSING
OUTPUT END COVER
OPTIONS
DR
10
White MotorsHB Series
Date: 2013Page 10.08 CROSS
CROSS
Stock No.Rotors (Displacement) Rotor Width RPM
per LPMMax.Flow Max. Pressure
List Pricecu.in/rev cc/rev inches lpm bar
HB03**5600 3.2 52 0.317 19.3 45 210
HB04**5600 4.6 76 0.463 13.2 68 210
HB05**5600 5.4 89 0.541 11.4 79 210
HB06**5600 6.8 111 0.681 9.0 95 210
HB08**5600 7.7 127 0.776 7.9 95 210
HB10**5600 10.0 164 1.001 6.1 95 210
HB12**5600 12.5 205 1.251 5.0 95 210
HB14**5600 15.5 254 1.551 4.0 95 210
HB18**5600 17.9 293 1.791 3.4 95 210
HB24**5600 24.9 409 2.501 2.4 95 170
300333900 Seal KitHousings Code Add to List Brake Code Add To List
SAE ‘A’ Style Flange (2 Hole Mount)SAE ‘A’ Style Flange (4 Hole Mount)SAE ‘A’ Style Flange (6 Hole Mount)Four Hole Square MountFour Hole With Mid MountSetback Flange (Wheel Motor)Setback Flange (Wheel Motor With Brake Mount)Setback Flange (Hubdrum Motor, Uses #51 Shaft)Setback Flange With 125mm Pilot, (Uses #70 Shaft Only)Short Brake W/O Trunnion Mount (Uses #63, #64 & #79 Shafts)Short Brake With Trunnion Mount (Uses #63, #64 & #79 Shafts)Short Brake With Top Ports (Uses #63, #64 & #79 Shafts)Brake, 7.115” Dia Pilot (Uses #61 Shaft Only)Short Motor (Uses #00 Shaft Only)
565859151707112429----
01
---------
44454654-
Output Shafts Code Add to List Brake Code Add To List
No Shaft (For Use With #01 Housing Only)1” Straight1-1/4” Straight25mm Straight32mm Straight35mm Tapered (#29 Setback Housing Only) (Specify Nut Option)35mm Tapered (#44, #45 & #46 Housing Only) (Specify Nut Option)1-1/4” Tapered (Specify Nut Option)1-1/4” Tapered (#44, #45 & #46 Housing Only) (Specify Nut Option)1-1/4” Tapered (#24 Hubdrum Housing Only) (Specify Nut Option)1-1/2” Tapered (#54 Brake Housing Only)1-1/2” Tapered (#24 Hubdrum Housing Only)1-1/2” Tapered (#44, #45 & #46 Housing Only)6B Spline (1” Dia)13 Tooth Spline (7/8” Dia)14 Tooth Spline (1-1/4” Dia)
005654575970-
53-
60-
51-
525055
------
79-
63-
61-
64--
75
End Cover Code Add to List
1/2-14 BSP.F Offset Manifold1/2-14 BSP.F Rear Ports1/2-14 BSP.F 180 Degree Side Ports1/2-14 BSP.F Offset Ports7/8-14 UNF-2B O-Ring Rear Ports7/8-14 UNF-2B O-Ring Offset Ports1-1/16-12 UN-2B 180 Degree Side Ports9/16-18 UN-2B O-Ring Side Ports
93287610
Options Code Add to List
No OptionsShuttle ValvePack Nut (1-1/4” Tapered Shaft Only)Brake & Drum (#24 Housing, #51 Shaft Only)Brake Shoes W/O Drum (#24 Housing, #51 Shaft Only)Drum W/O Brake Shoes (#24 Housing, #51 Shaft Only)Cross Flow End Cover (#0 & #7 End Covers Only)Free TurningSolid Nut (1-1/4” Tapered Shaft Only)Relief Valve Port End Cover (#0 & #7 End Covers Only)3000 PSI Relief Valve Installed (#0 & #7 End Covers Only)
0DPKVUGFXR
R3
ROTORHOUSING
OUTPUT END COVER
OPTIONS
HB
10
White MotorsDT Series
Date: 2013Page 10.09CROSS
CROSS
Stock No.Rotors (Displacement) Rotor Width RPM
per LPMMax.Flow Max. Pressure
List Pricecu.in/rev cc/rev inches lpm bar
DT19****00 18.3 300 1.001 3.30 132 210
DT25****00 22.8 375 1.251 2.70 132 210
DT28****00 28.3 465 1.552 2.20 150 175
DT33****00 32.7 536 1.791 1.90 150 160
DT46****00 45.6 748 2.501 1.30 150 160
DT56****00 56.7 929 3.104 1.10 150 140
DT66****00 63.9 1048 3.501 1.00 150 140
DT91****00 91.2 1496 5.002 0.67 150 100
DT99****00 127.7 2049 7.002 0.48 150 100
700666251 Seal Kit
Housings Code Add to List Brake Code Add To ListSAE ‘C’ Front Mount With 6.00” Dia B.C. Rear MountSAE ‘C’ Front Mount With 6.00” Dia B.C. & 125mm PilotSAE ‘C’ Front Mount With 8.25” Dia B.C. Rear MountBrake, 7.115” Dia Pilot (Uses #29 & #30 Shaft Only)125mm 6-Bolt (Uses #07 & #18 Shafts and #5 & #7 End Covers)
060716-
03
---
33-
Output Shafts Code Add to List Brake Code Add To List1-1/2” Tapered55mm Tapered (#23 Brake Housing Only)60mm Tapered1-1/2” Straight (European)1-1/2” Straight (USA)2.00” Straight (#23 Brake Housing Only)2-1/4” Straight40mm Straight50mm Straight14 Tooth Spline (1-1/4” Dia)17 Tooth Spline (European) (1-1/2” Dia)17 Tooth Spline (USA) (1-1/2” Dia)16 Tooth Spline (2-1/8” Dia)19 Tooth Spline (For #03 Housing With Warn Hub)23 Tooth Spline (For #03 Housing Without Warn Hub)
20-
232232-
252421362838260718
-30---
29---------
End Cover Code Add to ListManifold Ports, D-Shaped1-1/16-12 UN-2B O-Ring Ports, Round1-1/16-12 UN-2B O-Ring Ports, D-Shaped3/4-14 BSP.F Ports, Round3/4-14 BSP.F Ports, D-Shaped7/8 O-Ring Rear Ports, Round
358790
Options Code Add to ListNo OptionsSpeed Sensor (Single)Speed Sensor (Dual) Consult Cross for AvailabilityShuttle Valve (#3, #5 & #7 End Covers Only)Relief Valve Port End Cover (#5 & #7 End Covers Only)1000 PSI Relief Valve Installed (#5 & #7 End Covers Only)2000 PSI Relief Valve Installed (#5 & #7 End Covers Only)3000 PSI Relief Valve Installed (#5 & #7 End Covers Only)Free Turning (Recommended For Industrial Use)Warn Hub (For #03 Housing With #07 Shaft Only)
0ZQDR
R1R2R3FW
ROTORHOUSING
OUTPUT END COVER
OPTIONS
DT
10
White MotorsD9 Series
Date: 2013Page 10.10CROSS
CROSS
Stock No.Rotors (Displacement) RPM Max. Flow Max Pressure
List Pricecu.in/rev cc/rev per LPM lpm bar
800260*****AAAAA 15.6 256 3.75 136 207
800300*****AAAAA 17.9 294 3.25 159 207
800375*****AAAAA 22.4 367 2.62 204 207
800450*****AAAAA 27.8 455 2.12 204 207
800525*****AAAAA 32.1 525 1.87 204 207
800625*****AAAAA 38.1 623 1.62 204 207
800735*****AAAAA 44.8 734 1.37 204 172
800910*****AAAAA 55.6 911 1.12 204 172
8001K0*****AAAAA 62.7 1027 1.00 204 138
80088200 Seal Kit
800
HOUSINGROTOR SHAFT
AAAAA
PORTS
Housings Code Add to ListSAE C 4 Bolt 5” Pilot C8
Wheel Mount 4 Hole W8
Side Ports Code3/4” BSPP 7
1-5/16” UN 9
Output Shafts Code14 Tooth Spline (1-1/4”) * 23
1-1/2” Parallel 3/8” Key * 30
17 Tooth Spline (1-1/2”) * 33
2-1/4” Parallel 1/2” Key * 40
45mm Tapered ** 38
60mm Tapered ** D3
2-1/4” Parallel 1/2” Key ** 47
16 Tooth Spline 42
1-3/8” 6B Spline * 78
1-3/8” 6B Spline ** 46
* C8 Housing only. ** W8 Housing only.
Note: Flow and pressure are continuous operation.See catalogue for peak.
10
White BrakeSB Series
Date: 2013Page 10.11CROSS
CROSS
Stock No.Holding Torque Max. Release Pressure Full Release Pressure Mounting
Flange List Pricelb - in Nm PSI Bar PSI Bar
930225A11** 2000 225 3625 250 290 20 SAE ‘A’
930315A11** 2800 315 3625 250 290 20 SAE ‘A’
930415A11** 3700 415 3625 250 290 20 SAE ‘A’
930520A11** 4600 520 3625 250 450 31 SAE ‘A’
930620A11** 5500 620 3625 250 450 31 SAE ‘A’
HOUSINGS
930
HOLDING TORQUE SHAFT
HousingsA11 SAE ‘ A’ 2 Hole 1/4” BSPP Release Port
A31 SAE ‘ A’ 4 Hole 1/4” BSPP Release Port
ShaftsZW 1” Parallel Output with 1” 6B Splined Input
ZZ 1” 6B Splined Output with 1” 6B Splined Input
ZU 32mm Parallel Output with 1” 6B Splined Input
.54 (13,7)
2.67 (67,8)
3.75 (95,3)
17°
4.19 (106,4)
Brake Release Port
5.15 (130,8)5.09 (129,3)
3.250 (82,6)3.248 (82,5)
.24 (6)
4.53 (115,1) Max.
1.64 (41,6)3.255 (82,7)3.253 (82,6)
5.15 (130,8)5.09 (129,3)
.89 (22,6)
.34 (8,5) A10A11
1.67 (42,3)
*(4) Fill and Drain Ports
(2) M12 x 1.75Mounting Holes
.251 (6,4)
.250 (6,4).251 (6,4).250 (6,4)
1.110 (28,2)1.101 (28,0)
2.03 (51,6)
1.68 (42,7)
1.02 (25,9).970 (24,6)
MountingFlange
.70 (18) Min.
.18 (4,6)
45°5/16” - 18 UNC
.999 (25,4)
.998 (25,3)
ZW 1” Straight Output w/ 6-B Spline Input
1.372 (34,8)1.359 (34,5)
.276 (7,0)
.274 (7,0)
.394 (10,0)
.392 (9,9)
2.62 (66,5)
1.285 (32,6)1.235 (31,4)
MountingFlange
.70 (18)Min.
.46 (11,7)
45°
M8 x 1.25
1.260 (32,0)1.259 (31,9)
2.22 (56,4)
ZU 32mm Straight Output w/ 6-B Spline Input
.245 (6,2)
.243 (6,2)
.810 (20,6)
.805 (20,4)
2.03 (51,6)
1.68 (42,7)
MountingFlange
.70 (18) Min.
1.00 (25,4) Min. Spline
45°
5/16” - 18 UNC
.996 (25,3)
.992 (25,2)
ZZ 6-B Spline Output w/ 6-B Spline Input
10
Flangeable Valves
Cross Line Relief Valve suit Danfoss OMM, White WMStock No. Description Max. Flow Max. Pressure Weight Body List Price
FPMD15DVD1P3820 Cross Line Relief Valve 15 LPM 350 BAR 0.55 kg Aluminium
Date: 2013Page 10.12CROSS
CROSS
Springs
Code *Adjustable pressure range bar
Pressure increase bar/turn
Standard setting
barColour
05 5-60 15 5 White
10 20-130 30 20 Yellow
20 40-240 65 40 Green
35 50-350 100 50 Red
Cross Line Relief Valve suit Danfoss OMP/R/HStock No. Description Max. Flow Max. Pressure Weight Body List Price
FPMD40DFD2P1220 Cross Line Relief Valve 50 LPM 350 BAR 1.25 kg Aluminium
Springs
Code *Adjustable pressure range bar
Pressure increase bar/turn
Standard setting
barColour
05 5-50 10 5 White
10 30-100 20 30 Yellow
20 50-220 40 50 Green
35 80-350 80 80 Red
Type V1 & V2 BSPP A mm B mm C mm D mm E mm F mm G mm
FPMD15DVD1P 3/8 3/8” 50 50 19 30.4 13 30 17
10
Flangeable Valves
Cross Line Relief Valve suit Danfoss OMP/R/H, White WP/WRStock No. Description Max. Flow Max. Pressure Weight Body List Price
FPMD40DVD2P1220 Cross Line Relief Valve 50 LPM 350 BAR 1.05 kg Aluminium
Date: 2013Page 10.13CROSS
CROSS
Shuttle Valve suit Danfoss OMP/R/H, White WP/WRStock No. Description Max. Flow Max. Pressure Weight Body List Price
FPTDFD212 Shuttle Valve 60 LPM 210 BAR 0.47 kg Aluminium
Springs
Code *Adjustable pressure range bar
Pressure increase bar/turn
Standard setting
barColour
05 5-50 10 5 White
10 30-100 20 30 Yellow
20 50-220 40 50 Green
35 80-350 80 80 Red
10
Flangeable ValvesDouble Overcentre Valve with Brake Release suit Danfoss OMP/R/H, White WP/WR
Stock No. Description Max. Flow Max. Pressure Weight Body List Price
FPO60DVD212U20 Double Overcentre Valve 60 LPM 350 BAR 2.00 kg Aluminium
Date: 2013Page 10.14CROSS
CROSS
C1=1/2”BSPP
C2=1/2”BSPP
2236
22
223622 C3=1/4”BSPP
54
13.5
80
50.5 29.5
54
4.5
42
92.1
11
V2=1/2”BSPP31 18 31
2020
8040
V1=1/2”BSPP
2726
27
59 20
Double Overcentre Valve with Brake Release suit Danfoss OMP/R/H, White WP/WRStock No. Description Max. Flow Max. Pressure Weight Body List Price
FPO50DFD238U20 Double Overcentre Valve 60 LPM 350 BAR 2.00 kg Aluminium
Springs
Code *
Pilot Ratio
Adjustable pressure range bar
Pressure increase bar/turn
Standard setting
barColour
20 4 : 1 60-220 50 170 Green
20 8 : 1 60-220 50 170 Green
35 4 : 1 100-350 110 280 Red
35 8 : 1 100-350 110 280 Red
Springs
Code *
Pilot Ratio
Adjustable pressure range bar
Pressure increase bar/turn
Standard setting
barColour
20 4.25 : 1 60-220 70 170 Green
20 8 : 1 60-220 50 170 Green
35 4.25 : 1 100-350 120 280 Red
35 8 : 1 100-350 85 280 Red
10
White Rotary Flow DividersFD Series
Date: 2013Page 10.15CROSS
CROSS
White ‘Roller Stator’ Rotary Flow Dividers
Stock No. Type DescriptionPort Configurations Flow Rate
GPMDim ‘Y’ Dim ‘X’
List PriceInlets Outlets in mm in mm
FD00101000 2 Way Rotary Flow Divider 1 2 2 - 10 7.31 185.7 2.35 59.6
FD00181800 2 Way Rotary Flow Divider 1 2 10 - 30 8.23 209.0 2.81 71.3
FD00242400 2 Way Rotary Flow Divider 1 2 30 - 40 8.73 221.7 3.06 77.7
FD00181818 3 Way Rotary Flow Divider 1 3 4 - 40 10.92 277.4 - -
FD18181818 4 Way Rotary Flow Divider 2* 4 5 - 50 15.48 393.2 - -
* Both inlets must be used.
Flow Divider Features
The White Hydraulics’ flow dividers offer many advantages over other designs. All flow dividers utilise White Hydraulics’ patented Roller Stator Design. This design incorporates rollers for the critical sealing points of the rotor assembly. Benefits of this design include minimised leakage and less internal friction which result in higher mechanical and volumetric efficiency than other designs. The use of the Roller Stator design also guarantees more accurate output flows when pressure differentials are present at the outputs. The White Hydraulics’ flow dividers are also significantly quieter than many current designs, offering an advantage where application noise levels are critical.
The White Hydraulics’ flow dividers are available in 2, 3 and 4-way dividers with a large number of output ratios available. Output flows are available up to 50 GPM with operating pressures up to 4,000 psi peak.Features:• Three Zone Rotor Set• Accurate Output Flows• Smooth Output Delivery• Quiet Operation• Up To 50 GPM FlowsOptions:• 2, 3 And 4 Way Dividers• Numerous Output Ratios
5.47 (139)Max.
3.20 (81)Max.
2.61 (66)Max.
.524 (13,3)
.514 (13,1)
Ø 5.812(147,6)
CB
Dim A
Dim A
Dim B
Dim X
Dim A
Dim Y
Dim ADim X
5.00 (127)
1.80 (46)
.96(24)
2.62 (67)
.90(23)
10
Delta Rotary Flow DividersP Series
Date: 2013Page 10.16CROSS
CROSS
Delta ‘P’ Series Rotaty Flow Dividers
Stock No. Description No. of
Sections
Total Max Inlet
(GPM)
0-PSI Disp. Per Section (Gal/Rev)
Slip* (GPM /
100 PSI)
Max. Press.
Intermittent (PSI)
Max. Press. Continuous
(PSI)
Bolt Torque (Ft-Lb)
Max. Diff. Between
Section (PSI)List Price
PM2 Rotary Flow Divider 2 3.5 0.00047 0.026 2500 2000 13-17 1500
PM6 Rotary Flow Divider 2 9.5 0.00137 0.038 2000 1500 13-17 1000
P23 Rotary Flow Divider 2 21.0 0.00304 0.066 2000 1500 24-31 1000
P27 Rotary Flow Divider 2 44.0 0.00633 0.113 2000 1500 24-31 1000
P43 Rotary Flow Divider 2 70.0 0.0102 0.135 2000 1500 24-31 1000
P47 Rotary Flow Divider 2 100.0 0.0169 0.210 2000 1500 24-31 1000
PPM2 Rotary Flow Divider 4 7.0 0.00047 0.026 2000 1500 13-17 1000
*Values shown are for single section only.
Delta ‘P’ Series Rotaty Flow Dividers With Relief
Stock No. Description No. of Sections
Total Max Inlet
(GPM)
0-PSI Disp. Per Section (Gal/Rev)
Slip* (GPM /
100 PSI)
Max. Press.
Intermittent (PSI)
Max. Press. Continuous
(PSI)
Bolt Torque (Ft-Lb)
Max. Diff. Between
Section (PSI)List Price
PM2RV Rotary Flow Divider with Relief Valve
2 3.5 0.00047 0.026 2500 2000 13-17 1500
PM6RV 2 9.5 0.00137 0.038 2000 1500 13-17 1000
PPM2RV 4 7.0 0.00047 0.026 2000 1500 13-17 1000
*Values shown are for single section only.
PM2 & PM6 P23 & P27 P43 & P47
10
Delta Rotary Flow DividersPM & P Series, Buildable
Date: 2013Page 10.17CROSS
CROSS
Delta ‘PM’ & ‘P’ Series Rotaty Flow Dividers
Stock No. Description No. of Sections
Total Max Inlet
(GPM)
0-PSI Disp. Per Section Slip*
(GPM /100 PSI)
Max. Press.
Intermittent (PSI)
Max. Press.
Continuous (PSI)
Bolt Torque (Ft-Lb)
Max. Diff. Between Section (PSI)
List PriceCU IN REV
CC REV
PM44 Rotary Flow Divider 2 6 0.18 3 0.020 2000 1500 24.31 1000
PM444 Rotary Flow Divider 3 9 0.18 3 0.020 2000 1500 24.31 1000
PM4444 Rotary Flow Divider 4 12 0.18 3 0.020 2000 1500 24.31 1000
PM66 Rotary Flow Divider 2 9 0.32 5.2 0.025 2000 1500 24.31 1000
PM666 Rotary Flow Divider 3 14 0.32 5.2 0.025 2000 1500 24.31 1000
PM6666 Rotary Flow Divider 4 19 0.32 5.2 0.025 2000 1500 24.31 1000
PM88 Rotary Flow Divider 2 7 0.46 7.6 0.030 2000 1500 24.31 1000
PM888 Rotary Flow Divider 3 11 0.46 7.6 0.030 2000 1500 24.31 1000
PM8888 Rotary Flow Divider 4 15 0.46 7.6 0.030 2000 1500 24.31 1000
P211 Rotary Flow Divider 2 12 0.41 6.7 0.060 2000 1500 24.31 1000
P2111 Rotary Flow Divider 3 18 0.41 6.7 0.060 2000 1500 24.31 1000
P21111 Rotary Flow Divider 4 24 0.41 6.7 0.060 2000 1500 24.31 1000
P233 Rotary Flow Divider 2 20 0.7 11.5 0.068 2000 1500 24.31 1000
P23-60 Rotary Flow Divider 3 30 0.7 11.5 0.068 2000 1500 24.31 1000
P23-59 Rotary Flow Divider 4 40 0.7 11.5 0.068 2000 1500 24.31 1000
P255 Rotary Flow Divider 2 30 1.0 16 0.083 2000 1500 24.31 1000
P2555 Rotary Flow Divider 3 45 1.0 16 0.083 2000 1500 24.31 1000
P25555 Rotary Flow Divider 4 60 1.0 16 0.083 2000 1500 24.31 1000
P277 Rotary Flow Divider 2 44 1.46 24 0.113 2000 1500 24.31 1000
P27-60 Rotary Flow Divider 3 66 1.46 24 0.113 2000 1500 24.31 1000
P27-59 Rotary Flow Divider 4 88 1.46 24 0.113 2000 1500 24.31 100010
ADDITIONAL SECTIONSAS REQUIRED
OUTLET PORTS3/8 NPTF
2.75(69.9)TYP.
.67(17.1)
1.38(34.9)
A
1.13(28.6)
.56(14.3)
A1.38(34.9)
1.00(25.4)
.56(14.3)
.75(19.1)
2X
INLET PORTS3/8 NPTFBOTH ENDS
IN
4.63(117.7)
Ø.44MTG HOLE
4X
1.00(25.4)
2.00(50.8)2.75
(69.9)
2.75(69.9)
2X
OUTLET PORTS1/2 NPTFTYP
.75(19.1)
.92(23.4)TYP
ADDITIONAL SECTIONSAS REQUIRED
1.50(38.1)
A 1.85(46.9)
.68(17.4)
.56(14.3) .94
(23.8)
1.50(38.1)
INLET PORT1” NPTFBOTH ENDS
1.75(44.5)
1.38(34.9)
1.75(44.5)
4.00(101.6)
1.38(34.9)
1.75(44.5)
4.81(122.2)
0.44MTG HOLE
4X
IN
Typical Multi-Section P21-P27PM Series
MTE Rotary Flow DividersHSR Series
Date: 2013Page 10.18CROSS
CROSS
HSR Series Rotaty Flow Dividers
Stock No. Description No. of Sections
Total Max Inlet (GPM)
0-PSI Disp. Per Section (Gal/Rev)
Max. Press. Intermittent
(PSI)
Max. Press. Continuous
(PSI)
Max. Diff. Between
Section (PSI)List Price
HSR315153955 Rotary Flow Divider 2 44 .00633 5000 3000 750
HSR31010 Rotary Flow Divider 2 29 .00425 5000 3000 750
HPR27-59 Rotary Flow Divider 4 88 .00633 4000 2000 750
High PressureEqual Flow - With Relief
High pressure flow dividers come standard with two or four sections. Each section comes with a differential relief valve from output to input which allows a ‘lagging’ cylinder to catch up at end of stroke. Alternative multi-section and mixed section units are available on request.
IN
OUTOUT
Relief Valve Settings:
Standard setting on relief valve is 51 bar (750 psi) differential between outlet and inlet pressure. (These relief valves do not give system relief.)
Maximum total inlet flow (litres/min) is based on 3000 rpm. For a more quiet operation limit speed to between 1500 and 2500 rpm.
Bolt Torque (Nm) Dim A (mm) Dim B (mm) Weight (kg)
63.65 100.5 85 15.4
35 55
70
109
165
72
126
24
111
1-5/16” UNC Inlet PortsTyp. 2
Relief Valve**
7 Typ
39.5
10 Typ A
** These details apply for each additional section
B** 62.7 Dia. 11.2 Thru (x4)
1-1/16” UNC Outlet Ports**
10
top related