siemens dishwasher se24m850eu

Fill with rinse aid

Fill with detergent

Select programmeSum

mar

y of

inst

ruct

ions

for

dish

was

her

Brief and handy:everything your dishwasherneeds...Before using for the firsttime, read the installationand operating instructions!

Fill with special salt

Switch on appliancePress On/Off switch, running time of thechosen programme appears

When the display shows 0 (end of programme),press On/Off switch

Switch off the appliance Everything O.K...

en Set the water softening system * Quickly sorted ...

Find out the water hard-ness at your water utilitycompany and enter

* only before using the dish-washer for the first time orif the water hardnesschanges

Read off the setting ... and then set

– Hold down programme button B and switch on the mainswitch, then release the buttons. The display of button Band the number 4 set by the factory flash.

– Each time button B is depressed, the setting increases byone; if 7 has been reached, the display jumps back to 0.

– Switch off the main switch. The selected setting has beenstored in the appliance.

Reset

A B C

Dissolves limescale (not required for set value 0!)

Unscrewthe lid.

Only before usingthe dishwasherfor the first timepour approx. 1 l /2 pt water into thesalt opening.

Pour in max.1.5 kg / 3 lb 5 ozsalt (never deter-gent!)

Screw on thelid. Switch ondishwasherimmediately.

Everything is sparkling clean ... Refill whenever level indicator is light!

Press mark 1,lift up lid 2.

Pour inrinse aid .

Close thelid. CLICK!

Very dirty dishes, a lot of detergent ...

If required, openthe lid (press thepin).

Warning,

combination products are notsuitable for allprogrammes, follow manufac-turer’s instructions.

Pour indetergent .

Push the lidshut, press.PLOP!

Quick, economical or intensive ...

Programme overview

This overview lists the max. possible number ofprogrammes. The programmes supplied with yourappliance are indicated on the fascia.

The programme data are values measured in thelaboratory in compliance with Standard EN 50242.Deviations is practice are possible.

45�50�70� 65� 40�

Duration in minutes

Electricity consumption in kWh

Water consumption in litres

with Aquasensor

NormalIntensive Eco Quick Prerinse Gentle

Additional programmes ** Increased flexibility ...

** on some models

h.

Time selection

...switches on as soon asyou press the timeselection button: Alters the programmestart in hourly steps

Upper basket cleaning...Only the crockery in theupper basket is cleaned

9000

167

295

� 86

05�

���

1381,651613

1401,0514–

75 0,901411

300,8010–

190,05

4–

1401,6016–

Maintenance and care For perfect rinsing results ... Cleaning the waste-water pump *

Strainers ...Check, ifrequired, clean

Rotate filtercylinder, removefilter system ...

rinse underflowing water ...

Insert ... Screw in filtersystem NOTEMARK!

* With some models

– Ladle out water and remove filters– Unscrew cover (Torx T20)– Check area of fan impeller for foreign objects– Screw in cover and insert filters

Spray arms ...Removeblockages/deposits

Pull lower armupwards ...

Unscrew upperarm ...

Clean spray nozzlesunder flowing water(perhaps withtoothpick) ...

Insert lower arm ...

Screw in upper arm

Rectifying minor faults yourself ... ... as it is worth doing it yourself!

Fault Possible causes

Appliance is not running /stops

Check water supplyDisplay lights up

Supply fitting not open

Supply hose kinked

Supply fitting jammed or calcified

Open supply fitting.

Install supply hose without kinks.

1. Unscrew water connection.2. Clean filter in the water connection.3. Flow rate must be min. 9 l/min. whenwater supply is open.If the flow rate is less, replace thesupply fitting.

Remedial action

Plastic / utensilsdiscoloured

Too little detergent

Discoloration caused by food colourings(tomato sauce)

Follow manufacturer’s instructions(detergent).

Discoloration is harmless; subsequentrinse cycles will cause it to fade.

Residual waterin the appliance

Waste water pump blocked

The programme has not yet ended

Clean waste-water pump (see above).

Close appliance and switch on.or terminate programme (seeTerminating the programme).

Rust on the cutlery Cutlery not rust-resistantHard knife blades are more susceptible

Extraneous rust

Use dishwasher-proof cutlery.

Never wash rusting partsin the appliance.

Fault Possible causes Remedialaction

Stains and streaks

Milky film on the utensils(removable)

Rinse-aid dosage too high / too low

Glasses not dishwasher-proof.

Streaks: reduce dosage.

Water or limescale stains: increasedosage.

Use dishwasher-proof glasses.

Use a detergent suitable for glasses.

More information can be found in the operating instructions

Milky film, glassescloudy / dull (not removable)

Water softening system incorrectly set;

No salt

Correctly set water softening system.

Refill with salt.

Utensils are not clean

Sand or gritty residueon the utensils

Utensils are situated close togetheror one above the other

Too little detergent

Unsuitable programme selected

Spray arm nozzles blocked

Filters dirty, not seated firmly

Spray arms blocked

Separate the utensils, prevent contactpoints.

Follow manufacturer’s instructions(detergent).

Select a more intensive programme.

Clean the spray arms (see above).

Clean the filters (see above).

Arrange the utensils so that the sprayarms can rotate freely.

Stopping the programme ... Loading the dishwasher correctly ...

Press and hold the two reset buttons simultaneously forapproximately 3 seconds whilethe programme is running(RESET)

”0” appears

The programme will stopafter 1 minute

Switch off the appliance.Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,large remnants of jam, dairy products and food) according to the operating instructions and check thatthe spray arms can rotate freely.