sm6 kit assembly instructions

7/29/2019 SM6 Kit Assembly Instructions

1/14

notice de kit

kit assemblyinstructions

surge arresters GAMcubicle level C

parafoudres pourcellule GAM niveau C

SM6

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

2/14

Les centres de services du

groupe Schneider Electric sontoprationnels pour :

ingnierie et assistance techniquemise en serviceformationmaintenance prventive etcorrectiveadaptationspices de rechange

Faites appel votre agentcommercial qui vous mettra enrelation avec le centre deservices du groupe Schneider

Electric le plus proche.

group Schneider Electric servicecenters are there for:

engineering and technicalassistancestart-uptraining

preventive and correctivemaintenanceadaptation workspare parts

Call your sales representative

who will put you in touch withyour nearest group SchneiderElectric service centre.

Edition du : 09/10/2009S1A23043 revision : 00

En raison de lvolution des normes et du matriel,les caractristiques indiques par le texte et les imagesde ce document ne nous engagent quaprs confirmationpar nos services.

Conception, rdaction: Service DocumentationTechnique T&D

As standards, specifi cations and designs change from timeto time, please ask for confirmation of the information givenin this publication.

SCHNEIDER ELECTRIC http://www.schneider --- electric.com

35 rue Joseph Monier

CS 30323

92506 RUEIL MALMAISON CEDEX

Tl : +33 (0)1 41 29 70 00

Fax :+33 (0)1 41 29 71 00 Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

3/14

INFORMATION--CONSEIL

Nous attirons votre attention sur ce point particulier

DANGER

AVERTISSEMENT suivant iso 3864---2

suivant iso 3864---2

suivant iso 3864---2

ATTENTION

as per iso 3864---2

as per iso 3864---2

as per iso 3864---2

DANGER : si cette directive nest pas respecte,cela entranera la mort ou blessures graves.

DANGER: failure to follow thisinstruction will result in death or seriousinjury.

AVERTISSEMENT : si cette directive nest pas respecte,cela peut entraner la mort ou blessures graves.

WARNING: failure to follow this instruction may result in death or seriousinjury.

ATTENTION : si cette directive nest pas respecte,cela peut entraner des blessures.

Ce signal dalerte peut galement tre utilis pour signalerdes pratiques pouvant entraner des dommages pour le matrielRM6.

CAUTION: failure to follow this instruction may result in injuries.This alert signal can also be used to indicate practices that coulddamage the RM6 unit.

INFORMATION- ADVICE

We draw your attention to this specific point.

WARNING

CAUTION

S1A23043 revision : 00 1

symboles etconventions

symbols andconventions

Attention :vous trouvez lensemble

de ces symbolesci---dessous durantlintgralit du document,vous indiquant les degrsdes dangerosits selon lesdiffrentes mises ensituation.

Caution:you will find all the symbols

below throughout thedocument, indicatingthe hazard levelsdepending on thedifferent types of situation.

SCHNEIDER ELECTRIC votreservice/ foreword

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

4/142 S1A23043 revision : 00

contacter lunit servicede Schneider Electric pour

diagnostics et conseils

contact the SchneiderElectric service unit for

diagnosis and advice

Faites appel votre agentcommercial qui vousmettra en relation avec lecentre de services dugroupeSCHNEIDER ELECTRICle plus proche.

www.schneider--electric.comvous pouvez vous connectersur :

Call your sales representative who

will put you in contact with the closest

SCHNEIDER ELECTRIC group service

centre.

You can log on to:

www.schneider---electric.com

rgles de diffusion

distribution rulesATTENTION

CAUTION

Le but de cette publicationest de permettre linstallationcorrecte du matriel SM6.

The aim of this publicationis to enable the SM6 unitto be installed correctly.

ATTENTIONCAUTION

La reproduction totale ou partiellede ce manuel est interdite et seulsles agents de Schneider Electricpossdent un droit exclusifdutilisation.

This document is not a commercialdocument.It is a strictly technicaldocument drawn up bySchneider Electric.

rgles de scurit

safety rules

ATTENTIONCAUTION

Toutes les oprations dcritesci---aprs doivent tre effectuesen respectant les normes descurit en vigueur, sous laresponsabilit dune autorit

comptente.All the operations described belowmust be performed in compliancewith applicable safety standards,under the responsibilityof a competent authority.

AVERTISSEMENT

WARNING

Linstallateur doit tre habilitet autoris pour intervenir etmanipuler le matriel SM6.

The contractor must be certifiedand authorised to manipulateand perform work on the SM6unit.

ATTENTIONCAUTION

Nentreprenez le travail quaprsavoir lu et compris toutesles explications contenuesdans ce document.

Si la moindre difficult respecterces rgles se prsentait,veuillez vous adresser Schneider Electric.

Only undertake the work afterhaving read and understoodall the explanations given in thisdocument.If you have any difficultycomplying with these rules,

please contactSchneider Electric.

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

5/14

N.1

5

7

N.2 N.3

N.4 N.5

N.6 N.7

N.8 N.9

N.10 N.11

S1A23043 revision : 00 3

Contenu du kit S1A12712pour cellule GAM level C

Contents of kit S1A12712for cubicle GAM level C

tableau rfrence picesParts reference table

repre

repere

quantit

quantity

Nde pices

N parts

description

description

utilis pour parafoudre

used for surge arrestor

N1 1 3736266 collecteur horizontal/ horizontal collector HE30---HE21 ---HE15 ---HE12 ---HE9

N2 3 3736264 collecteur intermediaire/ intermediatecollector

HE30---HE21---HE15---HE12---HE9

N3 3 3736263 support/ support HE30---HE21---HE15---HE12---HE9

N4 1 3731025 tresse/ braid HE30---HE21---HE15---HE12---HE9

N5 3 3730633 connexion / connection HE30

N6 3 51238721F0 entretoise/ spacer HE30---HE21---HE15

N7 3 3730634 connexion / connection HE21---HE15---HE12---HE9

N8 3 51238720F0 entretoise/ spacer HE12---HE9

N9 6 3736275 entretoise/ spacer HE15(qte3)---HE12---HE9(qte6)

N10 1 S1A12540 sachet visserie/ srews and bolts bag HE30---HE21---HE15---HE12---HE9

N11 1 S1A23043 manuel dinstructions/ instructionsmanual

HE30---HE21---HE15---HE12---HE9

description du kit/description of the kit

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

6/14

A

4 S1A23043 revision : 00

prparation de lacellule

Enlever la tleinter---cellule A pour aiderau montage desparafoudres

preparing the cubicle

Remove the inter---cubiclepartition A to facilitatemounting the surgearresters

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

7/14

12

3

12

3

N.10

S1A12540

1

2

3

4

5

6

N.10

S1A12540

S1A23043 revision : 00 5

pr---quip lextrieur dela cellule

Monter 3 crous--cage M8) surla poutre parafoudre

pre ---equipping the cubicleexterior

Mount 3 cage---nuts M8 (onthe cubicle exterior) on thesurge arrester beam

pr---quip lintrieur de lacellule

Monter 6 vis--cage M6x20 (lintrieur de la cellule) sur lapoutre parafoudre

pre ---equipping the cubicleinterior

Mount 6 cage---nuts M6x20 (on

the cubicle interior) on thesurge arrester beam

pr--quipement de la cellule GAM /pre ---equipping the GAM cubicle

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

8/14

BB

3

2

1

3

1

2

1

N.10

N.10

N.10

6 S1A23043 revision : 00

principe dassemblage despices du kit S1A12712

HE30--HE21--HE15--HE12--HE9

Important : ne pas serrerlensemble de la visserie afin depermettre dajuster ulterieurementles pices 1,2 et 3.

RAPPEL

Le tableau reference des picesest disponible dans le chapitreprecedent description.

N

3: support (3736263) x3

Mode de fixation : 6 rondellescontacts de 6 mm+ 6 crou M6.

N2 : collecteur intermediaire(3736264) x3

N1 : collecteur horinzontal(3736266) x1

Nota : il est conseill de raliser lemontage des collecteurs (1) et (2)simultanment.

Mode de fixation : 3 rondellescontacts de 8 mm+ 3 visHM8.25

principle for assembling theparts in the S1A12712 kit

HE30---HE21---HE15---HE12---HE9

Important: do not tightenall the screws so thatit is possible to subsequentlyadjust the parts 1,2 and 3.

REMINDER

The parts reference table isavailable in the previous chapterdescription.

No. 3: support(3736263) x3Fastening method: 6 contactwashers 6 mm + 6 nuts M6.

No. 2: intermediate collector(3736264) x3

No. 1: horizontal collector(3736266) x1

Note: It is recommended to mount

the collectors (1) and (2)simultaneously.

Fastening method: 3 contactwashers 8 mm + 3 screwsHM8.25

principe dassemblage pour parafoudreHE30--HE21--HE15--HE12--HE9/

surge arrester assembling principleHE30---HE21---HE15---HE12---HE9

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

9/14

A

3736266

4

4

partie suprieure

partie infrieure

4

A

B

N.10

N.10

upper part

lower part

S1A23043 revision : 00 7

prparation de la tresse dela mise la terre

avant montageDmonter lcrou A ( M 8 ) etrondelle contact ( 8 mm).

preparing the earthingbraid

before mounting

Remove the nut A (M8) andthe contact washer ( 8 mm).

montage de la tresse demasse

3731025

4

AB

A : partie suprieure

La tresse (4) se fixe sur lecollecteur horizontal (3736266).

Mode de fixation : 2 rondellescontacts ( 8 mm) + 1 visHM8.25, crou M8.

B : partie infrieure

Mode de fixation : rondellecontacts ( 8 mm) + crou M8.

mounting the earthing braid

A : upper partThe braid(4) is fixed on the

horizontal collector(3736266).

Fastening method: 2 contactwashers ( 8 mm) + 1 screwHM8.25, nut M8.

B : lower part

Fastening method: contactwashers ( 8 mm) + nut M8.

adaptation de la tresse de masse/adapting the earthing braid

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

10/14

N.3

x3

A

A

N.10

barre GAM N.6

N.5

N.6

partie basse

partie haute

connection barre GAM

x3

x3

N.5

N.6

N.5

N.10

N.10

N.5

lower part

upper part

GAM bar

GAM bar connection

8 S1A23043 revision : 00

montage de 3 parafoudresde type (HE30)

niveau infrieur de lacellule (1re tape)

Adapter les 3 parafoudres A(1 parafoudre par phase) sur les 3supports existants N3

Fixation par 3 rondelles contacts 12+3 vis HM12.30, utiliser lesachet visserie N10.

mounting 3 HE30 surgearresters

lower section of thecubicle (1st step)

Adapt the 3 surge arresters A(1 surge arrester/per phase) on the3 existing supports no. 3

Fastening with 3 contact washers 12 + 3 screws HM 12.30, usethe screw sachet no. 10.

2 me tape

partie haute :

Fixation des 3 connexions N5 surles barres GAM avec 3 rondellescontacts 10 + 3 crous M10.

2nd step

upper part :

Fastening the 3 connections no. 5

on the GAM bars with 3 contactwashers 10 + 3 nuts M10.

partie basse :

Monter les 3 entretoises N6 etles connections N5.

Fixation sur parafoudre : 3rondelles Grower 12 et 3 visHM12.50.

lower part :

Mount the 3 spacers no. 6 and theconnections no. 5.

Fastening on surge arrester: 3Grower washers 12 and 3

screws HM12.50.

adaptation dun parafoudre de typeHE30 / adapting a HE30 surge arrester

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

11/14

N.3

x3A

A

N.10

barre GAM

N.7

N.7

N.6

N.7

N.6

lower part

partie haute

GAM bar connection

x3

x3 N.10

N.10upper part

connection barre GAM

GAM bar

partie basse

S1A23043 revision : 00 9

montage de 3 parafoudresde type (HE21)

niveau infrieur de lacellule (1re tape)

Adapter les 3 parafoudres (1parafoudre par phase) A sur les 3supports existants N3

Fixation par 3 rondelles contacts12+3 vis HM12.30, utiliser lesachet visserie N10.

mounting 3 HE21surge arresters

lower section of thecubicle (1st step)

Adapt the 3 surge arresters A(1 surge arrester per phase) on the3 existing supports no. 3

Fastening with 3 contact washers12 + 3 screws HM12.30, use the

screw sachetno. 10.

2 me tape

partie haute :

Fixation des 3 connexions N7 surles barres GAM avec 3 rondellescontacts 10 + 3 crous M10.

2nd step

upper part :

Fastening the 3 connections no. 7on the GAM bars with 3 contactwashers 10 + 3 nuts M10.

partie basse :

Fixation des 3 entretoises N6 etles 3 connexions N7.

Fixation sur parafoudre : 3rondelles Grower 12 et 3 visHM12.50.

lower part :

Mount the 3 spacers no. 6 and theconnections no. 7.

Fastening on surge arrester: 3Grower washers 12 and 3

screws HM12.50.

adaptation dun parafoudre de typeHE21/ adapting a HE21 surge arrester

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

12/14

N.3

x3

A

A

N.10

N.9

N.6

N.7

N.7

GAM bar connection

N.7

N.7

x3

N.10

x3

A B

lower mounting upper mounting

A B

N.10

connection barre GAM

montage infrieur montage suprieur

10 S1A23043 revision : 00

montage de 3 parafoudresde type (HE15)

niveau infrieur de lacellule (1re tape)

Adapter les 3 parafoudres (1parafoudre par phase) A sur les 3supports existants N3

Fixation par 3 rondelles contacts12+3 vis HM12.30, utiliser lesachet visserie N10.

mounting 3 HE15 surgearresters

lower section of thecubicle (1st step)

Adapt the 3 surge arresters A(1 surge arrester/per phase) on the3 existing supports no. 3

Fixation par 3 rondelles contacts12+3 vis HM12.30, utiliser le

sachet visserie N10.

2 me tape

H A : partie basse, monter les 3entretoises (1 entretoise parphase) N9, ainsi que les 3entretoises (1 entretoise parphase) N6 et les 3 connexionsN7.

Fixation sur parafoudres :3rondelles Grower 12 et 3 visHM12.90.

2nd step

H A : lower part, mount the 3

spacers (1 spacer per phase)no. 9, as well as the 3 spacers(1 spacer per phase) no. 6 andthe 3 connections no. 7.

Fastening on surge arresters: 3Grower washers 12 and 3 screwsHM12.90.

H B : partie haute ,fixation des 3connexions N7 sur les barres dela GAM par 3 rondelles contacts10 et 3 crous M10.

H B : upper part, fastening of the3 connections no. 7 on the GAM

bars with 3 contact washers10 and 3 nuts M10.

adaptation dun parafoudre de type HE15/adapting a HE15 surge arrester

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

13/14

N.8

N.3surge arresters

B

N.10

parafoudres

N.10

N.9

N.7

N.7

N.7

N.7

N.10

N.7

N.7N.10

N.7N.10N.10

connection barre

GAM

N.10

S1A23043 revision : 00 11

montage parafoudres (HE9

ou HE12)

niveau infrieur de la cellule(1 re tape)

Monter les 3 entretoises N8 et les3 parafoudres B sur les 3 supportsN3Fixation par 3 rondelles contacts 12 et 3 vis HM12x50, utiliser lesachet visserie N10.

mounting surge arresters(HE9 or HE12)

lower section of the cubicle

(1st step)Mount the 3 spacers no. 8 and the3 surge arresters B on the 3

supports no.3Fastening with 3 contact washers12 and 3 screws HM12x50, usethe screw sachet no. 10.

2me tape : partie basse

Monter les 6 entretoises N9 avecles 3 connexions N7.

Fixation sur parafoudre par 3rondelles Grower 12 et 3 vis

HM12.110

2nd step: lower part

Mount the 6 spacers no. 9 with the3 connections no. 7.

Fastening on surge arrester with 3Grower washers 12 and 3 screwsHM12.110

partie haute :

Fixation des 3 connexions N7 surles barres GAM avec 3 rondellescontacts 10 + 3 crous M10.

upper part :

Fastening of the 3 connectionsno. 7 on the GAM bars with 3contact washers 10 and 3 nutsM10.

adaptation dun parafoudre de type HE9ou HE12 / adapting a HE9 or HE12 surge

arrester

Released for ManufacturingPrinted on 2010/06/24

7/29/2019 SM6 Kit Assembly Instructions

14/14

A

vrification aprsmontageAprs assemblage desparafoudres, sassurer que toutesles pices sont correctementbloquesRemettre la tle inter---cellule A.

checking aftermounting

After assembling the surgearresters, ensure that all the partsare blocked properly

Refit the inter---cubicle partition A.

verification /verification

Released for Man fact ring