ss7 glossary - squire technologies · ss7 glossary squire technologies – confidential document...
Post on 15-Aug-2020
5 Views
Preview:
TRANSCRIPT
SS7 Glossary
Document SQ00481
Version 2.6
©Squire Technologies
This document is the property of Squire Technologies. Information contained herein is confidential. This document, either in whole or in
part, must not be reproduced or disclosed to others or used for purposes other than that for which it has been supplied, without Squire
Technologies prior written permission, or, if any part hereof is furnished by virtue of a contract with a third party, as expressly
authorised under that contract.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 2 of 124
Change History
Version Change Made Author Authorised Date
2.0 Added Table of Contents and changed Version Number
DR AC 10.02.2014
2.1 Added CAP SSN Attribute of SS7 Stack.
BT BT 12.08.2014
2.2 Added CAMEL Phases Attribute of SS7 Stack.
BT BT 10.10.2014
2.3 Added Stats for the ASP, AS, SCTP, L3Label, TcapLabel and SccpLabel
JF JF 15.07.2015
2.4 Added INAP Application Context Attribute to SS7 Stack
BT BT 21.09.2016
2.5 Added XML Resource JF JF 01.06.2017
2.6 Updated entries below to be current:
2.5.3.41 M2PA Timer
2.6.3.20 Options 2.6.3.21 send CVT 2.6.3.22 Send CQM 2.10.3.26 M3UA AS
2.10.3.27 SSME XML
2.10.3.28 Tx Bits Throttle 2.10.3.29 Tx MSU Throttle 2.10.3.30 Tx Congestion
2.10.3.31 Tx Failure 2.10.3.32 Routing Failures
2.10.3.33 Rx UDTS
2.11.3.42 Ignore API Client
2.13.3.36 Options 2.14.3.28 displayRegistrations
2.10.3.8 Transfer Report
BT SS 11.11.2019
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 3 of 124
Contents 1.0 Introduction ................................................................................................. 6
1.1 Resource Name ............................................................................................. 6
1.2 Resource Identifier ......................................................................................... 6
1.3 Attribute ..................................................................................................... 6
1.4 Value .......................................................................................................... 6
2.0 Resources .................................................................................................... 7
2.1 Common Attributes ........................................................................................ 7
2.1.1 Status .................................................................................................... 7
2.1.2 Flags ..................................................................................................... 7
2.1.3 Inservice ................................................................................................ 8
2.1.4 Outservice .............................................................................................. 8
2.1.5 Description ............................................................................................. 8
2.1.6 Options .................................................................................................. 9
2.2 Card ........................................................................................................... 9
2.2.1 Description ............................................................................................. 9
2.2.2 Products ................................................................................................ 9
2.2.3 Attributes ............................................................................................... 9
2.3 Driver ........................................................................................................ 15
2.3.1 Description ............................................................................................ 15
2.3.2 Products ............................................................................................... 15
2.3.3 Attributes .............................................................................................. 15
2.4 Interface .................................................................................................... 15
2.4.1 Description ............................................................................................ 15
2.4.2 Products ............................................................................................... 15
2.4.3 Attributes .............................................................................................. 15
2.5 Signalling Link .............................................................................................. 19
2.5.1 Description ............................................................................................ 19
2.5.2 Products ............................................................................................... 19
2.5.3 Attributes .............................................................................................. 19
2.6 Circuit ....................................................................................................... 27
2.6.1 Description ............................................................................................ 27
2.6.2 Products ............................................................................................... 27
2.6.3 Attributes .............................................................................................. 27
2.7 Circuit Group ............................................................................................... 33
2.7.1 Description ............................................................................................ 33
2.7.2 Products ............................................................................................... 33
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 4 of 124
2.7.3 Attributes .............................................................................................. 33
2.8 Originating Point........................................................................................... 35
2.8.1 Description ............................................................................................ 35
2.8.2 Products ............................................................................................... 35
2.8.3 Attributes .............................................................................................. 35
2.9 Destination Point .......................................................................................... 38
2.9.1 Description ............................................................................................ 38
2.9.2 Products ............................................................................................... 38
2.9.3 Attributes .............................................................................................. 38
2.10 Linkset ................................................................................................... 41
2.10.1 Description ......................................................................................... 41
2.10.2 Products ............................................................................................ 41
2.10.3 Attributes ........................................................................................... 42
2.11 SS7 Stack ................................................................................................. 48
2.11.1 Description ......................................................................................... 48
2.11.2 Products ............................................................................................ 48
2.11.3 Attributes ........................................................................................... 48
2.12 MTP Route ............................................................................................... 57
2.12.1 Description ......................................................................................... 57
2.12.2 Products ............................................................................................ 57
2.12.3 Attributes ........................................................................................... 57
2.13 SCTP ...................................................................................................... 61
2.13.1 Description ......................................................................................... 61
2.13.2 Products ............................................................................................ 61
2.13.3 Attributes ........................................................................................... 61
2.14 ASP ........................................................................................................ 70
2.14.1 Description ......................................................................................... 70
2.14.2 Products ............................................................................................ 70
2.14.3 Attributes ........................................................................................... 70
2.15 AS ......................................................................................................... 76
2.15.1 Description ......................................................................................... 76
2.15.2 Products ............................................................................................ 76
2.15.3 Attributes ........................................................................................... 76
2.16 L3 Label / SCCP Label / TCAP Label ................................................................ 82
2.16.1 L3 Label ............................................................................................. 82
2.16.2 SCCP Label ......................................................................................... 90
2.16.3 TCAP Label ....................................................................................... 116
2.17 MTP CDR ............................................................................................... 119
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 5 of 124
2.17.1 Description ....................................................................................... 119
2.17.2 Products .......................................................................................... 119
2.17.3 Attributes ......................................................................................... 120
2.18 XML ..................................................................................................... 121
2.18.1 Description ....................................................................................... 121
2.18.2 Products .......................................................................................... 121
2.18.3 Attributes ......................................................................................... 121
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 6 of 124
1.0 Introduction The SVI controls all aspects of the system by abstracting the system down to a number of database
resources. These resources are further divided into sub resource types that describe the operation
of a given resource. There are a number of instances of a given resource and each resource has a
number of configurable attributes.
These resources are used to allow the administrator to configure and maintain the system.
All of these resources are arranged into a parent-child hierarchical arrangement. When started up
the SVI will bring the resources into service starting with the system resource and continuing down
through the children resources. A resource will only be brought into service once its parent
resource is configured and in-service.
Each resource has the following components
1.1 Resource Name
Each resource has a unique name which provides a unique operation for the SVI product.
1.2 Resource Identifier An individual resource instance is identified by a unique name.
1.3 Attribute The attribute field is the attribute of the resource that is to be configured. These are described for
each resource within this document.
1.4 Value
This field contains the value of the attribute. The following type of values are valid:
Type Description
Integer This is a number in either decimal or hexadecimal format. If the number is in hexadecimal format the 'H' character is prefixed to the number to indicate it is a hexadecimal number (Ha3)
Drop Down List This type of value provides a definitive list of options from which the user can select one of the options
Resource Identifier This is a drop down list which will provide all configured resources of the same type allowing the user to select a single instance of a resource
Bit Mask Flag This type of value provides the user with a list of options from which the user can choose multiple choices.
Integer range The integer range field is a list including ranges of integers for example 1,2,3-10,12-17,20
User String This is a NULL terminated ASCII character string
IP Address This describes an IP address ie (192.168.2.182)
Boolean A Boolean flag is either True or False
Resource Identifier Range
This allows for multiple resources to be identified
Digit Match A digit match is a string of E164 numbers with the special characters '
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 7 of 124
2.0 Resources
2.1 Common Attributes
The following section contains attributes that are common to all resources
2.1.1 Status This defines the status of the attribute, which will either be in service (INS) or out of service (OOS).
Description
This defines the status of the resource instance. When configuring managed resources this should
be set to Start, all other resource types should be INS.
2.1.1.1 Definition
Applicable Modes User Type
All Read Write Licensed
Drop Down List
2.1.1.2 Values
Value Description
Niu Instance of resource not configured on system
Osf Resource is waiting for parent to be in service before it attempts to come into service
Oos The Resource has been manually removed from service
Osc The Resource is waiting for the parent to come into service before it attempts to configure this resource
Osd The resource's parent is out of service and will come straight back into service once the resource's parent is in service.
Osfd The
Oscp The resource is currently attempting to be configured
Osp The resource is currently attempting to come into service
INS The resource is INSERVICE
Start This pre-configures the resource to its correct startup state
ERR An Error has occurred on this resource.
2.1.2 Flags
2.1.2.1 Description
The following flags define internally the behaviour of the resource. These are not user defined and
are provided only for information purposes.
2.1.2.2 Definition
Applicable Modes User Type
All Read None
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 8 of 124
2.1.2.3 Values
Value Description
Secure This resource will be secured on a fail over
Applied This indicates that a resource has been reconfigured and the system needs to reapply the configuration to the resource owner
Add Indicates that the resource is scheduled to be added to the system hierarchy
Remove Indicates that the resource is scheduled to be removed from the system hierarchy
Start Indicates that the resource is scheduled to be started
Reconfigured Indicates that the resource has been reconfigured and requires to be Removed then added and then started
Read This attribute has read permissions
Write This attribute has write permissions
No-Default This resource will not be displayed in the CLI if the default value is configured
No-Secure Do not secure this resource at failover
No-Init Do not initialise this
No-GUI Do not display this attribute in the GUI
Licensed The number of instances of this resource is licensed
2.1.3 Inservice
2.1.3.1 Description
The Inservice attribute displays the time that this resource came into service.
2.1.3.2 Definition
Applicable Modes User Type
All resources Read Time
2.1.4 Outservice
2.1.4.1 Description
The Outservice attribute displays the time that this resource last went from an in service state to
an out of service state.
2.1.4.2 Definition
Applicable Modes User Type
All resources Read Time
2.1.5 Description
2.1.5.1 Description
Description is a free text field to allow for a human readable name of the resource. Please note
that this field is automatically populated by the SVI-MS from the “Name” input field.
2.1.5.2 Definition
Applicable Modes User Type
Read Write
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 9 of 124
No-Default
2.1.6 Options
2.1.6.1 Description
These are a set of options which relate to the resource in question that you can enable or disable at
any time.
2.1.6.2 Definition
Applicable Modes User Type
Read Write No-Default
2.1.6.3 Values
Value Description
SNMP-Trap If the resource changes state, an SNMP trap will be sent to the address configured on the debug resource.
2.2 Card
2.2.1 Description
The card resource defines the operation and configuration of specialised telephony hardware
contained in the product.
2.2.2 Products
SVI-MG | SVI-9225 | SVI-STP | SVI-SG
2.2.3 Attributes
2.2.3.1 Map
2.2.3.1.1 Description When using different type of telephony hardware this attribute allows the same hardware to be
grouped together with each group starting from 0. When using the same type of hardware this will
have the same instance as the resource instance.
2.2.3.1.2 Definition
Applicable Modes User Type
All cards Read Write
Integer
2.2.3.2 Type
2.2.3.2.1 Description This specifies the particular type of telephony hardware that is being used
2.2.3.2.2 Definition
Applicable Modes User Type
All card types Read Drop Down List
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 10 of 124
Write
2.2.3.2.3 Values
Value Description
NS700 TDM Signalling only PCI card (Applicable to all MPACXXXX cards)
TP260 E1/T1 TDM to VoIP media and signalling card in PCI form factor
TP1610 E1/T1 TDM to VoIP media and signalling card in CPCI form factor
TP6310 STM-1 TDM to VoIP media and signalling card in CPCI form factor
Sangoma IP Only D500 Transcoding Card
2.2.3.3 Driver
2.2.3.3.1 Description Contains the identity of the software driver resource that the particular card is registered to.
2.2.3.3.2 Definition
Applicable Modes User Type
All card types Read Write
Resource Identifier
2.2.3.4 Download
2.2.3.4.1 Description Contains the name of the cards download image.
2.2.3.4.2 Definition
Applicable Modes User Type
All card types Read Write
String
2.2.3.5 Role
2.2.3.5.1 Description Describes the timing role within a H100/H110 synchronised telephony bus environment.
2.2.3.5.2 Definition
Applicable Modes User Type
All card types Read Write
Drop Down List
2.2.3.5.3 Values
Value Description
A Primary Master Provides the source port timing to the H100 A Primary Master bus
B Primary Master Provides the source port timing to the H100 B Primary Master bus
A Secondary Master Provides the source port timing to the H100 A Secondary Master bus
B Secondary Master Provides the source port timing to the H100 B Secondary Master bus
A Slave Takes its timing from the A bus
B Slave Takes its timing from the B bus
2.2.3.6 Source
2.2.3.6.1 Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 11 of 124
If the card is providing timing to the H100 A/B primary or secondary bus this defines the onboard
source of the timing.
2.2.3.6.2 Definition
Applicable Modes User Type
All card types Read Write
Drop Down List
2.2.3.6.3 Values
Value Description
Port 0 The bus timing is originated from Port 0 on the card
Port 1 The bus timing is originated from Port 1 on the card
Port 2 The bus timing is originated from Port 2 on the card
Port 3 The bus timing is originated from Port 3 on the card
Port 4 The bus timing is originated from Port 4 on the card
Port 5 The bus timing is originated from Port 5 on the card
Port 6 The bus timing is originated from Port 6 on the card
Port 7 The bus timing is originated from Port 7 on the card
Internal The bus timing is originated from the internal clock on the card
None This card does not provide timing to the bus
2.2.3.7 BusType
2.2.3.7.1 Description This defines the type of telephony bus used on the TP260 if it is shipped with the MVIP option.
2.2.3.7.2 Definition
Applicable Modes User Type
Card type TP260 only Read Write
Drop Down List
2.2.3.7.3 Values
Value Description
H100 The H100 bus is being used on this card
MVIP The MVIP bus is being used on this card
H110 The H110 bus is being used on this card
2.2.3.8 Address / Address Port 0
2.2.3.8.1 Description For telephony cards that are connected over IP, this defines the IP address of the card.
2.2.3.8.2 Definition
Applicable Modes User Type
All cards connected over IP Read Write No-Default
IP address
2.2.3.9 Address Port 1
2.2.3.9.1 Description For telephony cards that are connected over IP and have a secondary NIC connection. this defines
the IP address of that connection.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 12 of 124
2.2.3.9.2 Definition
Applicable Modes User Type
All cards connected over IP Read Write No-Default
IP address
2.2.3.10 Subnet
2.2.3.10.1 Description For the TPxxx range of cards that defines the subnet mask of the IP connection.
2.2.3.10.2 Definition
Applicable Modes User Type
For TP cards only Read Write No-Default
IP subnet mask address i.e. 255.255.255.248
2.2.3.11 Gateway
2.2.3.11.1 Description For TP cards this defines the default gateway address to be used.
2.2.3.11.2 Definition
Applicable Modes User Type
TP cards only Read Write No-Default
IP address
2.2.3.12 Selfboot
2.2.3.12.1 Description This is set to True if the Card being used is a NS700 card used in self boot mode
2.2.3.12.2 Definition
Applicable Modes User Type
NS700 card used in self boot mode
Read Write No-Default
Boolean
2.2.3.13 G168EC
2.2.3.13.1 Description This sets the Echo Cancellation tail length for a call with Echo cancellation
2.2.3.13.2 Definition
Applicable Modes User Type
TP cards Read Write No-Default
Drop List
2.2.3.13.3 Values
Value Description
Off Disable Echo Cancellation
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 13 of 124
32ms 32 milliseconds echo cancellation tail length
64ms 64 milliseconds echo cancellation tail length
128ms 128 milliseconds echo cancellation tail length
2.2.3.14 H1000 Termination
2.2.3.14.1 Description This defines if the telephony card is terminating the end of the telephony bus.
2.2.3.14.2 Definition
Applicable Modes User Type
TP cards Read Write No-Default
Boolean
2.2.3.15 Syslog-Enable
2.2.3.15.1 Description This turns on extra debugging on the card if set to True. The debug is delivered over IP to a debug
server.
2.2.3.15.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop down List
2.2.3.15.3 Values
Value Description
Disable Disable logging
Enable Enable logging
2.2.3.16 Syslog-IP
2.2.3.16.1 Description This sets the IP address of the debug server which is collecting the debug information.
2.2.3.16.2 Definition
Applicable Modes User Type
All Read Write No-Default
IP Address
2.2.3.17 Syslog-Port
2.2.3.17.1 Description This sets the IP address port of the debug server which is collecting the debug information.
2.2.3.17.2 Definition
Applicable Modes User Type
All Read Write No-Default
Port Address
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 14 of 124
2.2.3.18 Enable Debug
2.2.3.18.1 Description For NS700 cards this command is used to activate the debug.
2.2.3.18.2 Definition
Applicable Modes User Type
NS700 Read Write No-Default
Command
2.2.3.18.3 Values
Value Description
Disable Disable logging
Enable Enable logging
2.2.3.19 Tp-Sig-Channels / Add Tp-Sig-Channel
2.2.3.19.1 Description When using the TP cards for signalling DSP channels need to be reserved for handling the signalling
on a given timeslot on an E1/T1. The DSP channels are linear from 0-30 for the first E1, 31-61 for
second E1, etc. Therefore to set up two signalling links on timeslot 1 on the first two interfaces the
DSP channels 0 and 31 would be used.
2.2.3.19.2 Definition
Applicable Modes User Type
TP cards Read Write No-Default
Integer Array
2.2.3.20 Internal-TFTP-Server
2.2.3.20.1 Description Used to provide the TP260 card with the IP of the TFTP server to download its firmware/config
from.
2.2.3.20.2 Definition
Applicable Modes User Type
All Read Write No-Default
IP Address
2.2.3.21 Options
2.2.3.21.1 Description This allows for additional configuration options.
2.2.3.21.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop Down List
2.2.3.21.3 Values
Value Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 15 of 124
SNMP-Trap This provides an SNMP trap when the card status changes state
2.3 Driver
2.3.1 Description The driver resource describes the behaviour of the interface between a card resource and the SVI
system. Multiple cards of the same type can be associated with a single driver.
2.3.2 Products
SVI-MG | SVI-9225 | SVI-STP | SVI-SG
2.3.3 Attributes
2.3.3.1 Type
2.3.3.1.1 Description
The behaviour type of the resource instance.
2.3.3.1.2 Definition
Applicable Modes User Type
All Read Write
Drop down List
2.3.3.1.3 Values
Value Description
NS700 Driver For all MPACXXXX cards
TP260 Driver TPNCP Behaviour type when controlling the TP cards over IP using the native TPNCP API TP1610 Driver TPNCP
TP6310 TPNCP
Sangoma Driver For D500
2.4 Interface
2.4.1 Description
For a TDM enabled system the interface resource is a TDM interface that is either located directly
on the SVI or on a third party media gateway.
For the SBC the interface is the connection between the signalling SVI and the RTP routers which
provide handling of the media strings.
2.4.2 Products SVI-MG | SVI-9225 | SVI-STP | SVI-SG | SVI-SBC | SVI-MGC
2.4.3 Attributes
2.4.3.1 Type
2.4.3.1.1 Description
The behaviour type of the resource instance.
2.4.3.1.2 Definition
Applicable Modes User Type
All Read Write
Drop Down List
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 16 of 124
2.4.3.1.3 Values
Value Description
ISDN Cable This interface is an ISDN cable either located on the SVI or on a third party media gateway
SS7 Cable This interface is an SS7 Cable either located on the SVI or on a third party media gateway
STM1 SS7 Cable This interface is an STM-1 SS7 interconnect cable located on the SVI
STM1 ISDN Cable This interface is an STM-1 ISDN interconnect cable located on the SVI
TP260 Cable
Megaco Cable This interface is on a third party Media Gateway controlled via MEGACO/H.248
MG Ethernet This interface defines the connection between the SVI and individual RTP routers
2.4.3.2 Card
2.4.3.2.1 Description
For interfaces connected locally on the SVI this defines the card instance that the interface is
connected to.
2.4.3.2.2 Definition
Applicable Modes User Type
As defined Read Write No-Default
Resource Identifier
2.4.3.3 Media Gateway, Media GW
2.4.3.3.1 Description
For connections to a media gateway device this defines the Media Gateway resource instance that
the interface is located on.
2.4.3.3.2 Definition
Applicable Modes User Type
As defined Read Write
Resource Identifier
2.4.3.4 TrunkMap
2.4.3.4.1 Description
Defines the mapping of the interface onto the card it is assigned to. Note required to be set by
user.
2.4.3.4.2 Definition
Applicable Modes User Type
As defined Read Write No-GUI
2.4.3.5 BoardMap
2.4.3.5.1 Description
Defines the mapping of the interface onto the card it is assigned to. Note required to be set by
user.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 17 of 124
2.4.3.5.2 Definition
Applicable Modes User Type
As defined Read Write No-GUI
2.4.3.6 Crc
2.4.3.6.1 Description
For NS700 card type interfaces terminating on the SVI this attribute defines if CRC is active on the
interface.
2.4.3.6.2 Definition
Applicable Modes User Type
NS700 type cards Read Write
Drop Down List
2.4.3.6.3 Values
Value Description
CRC ON CRC is active on this interface
CRC OFF CRC is not active on this interface
2.4.3.7 Electrical
2.4.3.7.1 Description
This defines the electrical characteristics of NS700 type interfaces terminating on the SVI.
2.4.3.7.2 Definition
Applicable Modes User Type
NS700 type cards Read Write
Drop Down List
2.4.3.7.3 Values
Value
E1 75 HDB3
E1 120 HDB3
T1 100 SF_B8ZS
T1 100 SF_AMI
T1 100 ESF_B8ZS
T1 100 ESF AMI
E1 75 AMI
E1 120 AMI
2.4.3.8 Name
2.4.3.8.1 Description
This defines the MGCP interface name for connection of the SVI to a media gateway via MGCP.
2.4.3.8.2 Definition
Applicable Modes User Type
All Read Write
User String
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 18 of 124
2.4.3.9 Value Name
2.4.3.9.1 Description
End of Life
2.4.3.10 Default Circuits
2.4.3.10.1 Description
End of Life
2.4.3.11 Suffix Name
2.4.3.11.1 Description
End of Life
2.4.3.12 Tdmc Gain
2.4.3.12.1 Description
For H.248 remote media gateway's this allows for the gain to be set on the interface.
2.4.3.12.2 Definition
Applicable Modes User Type
H.248 remote gateways Read Write
Integer
2.4.3.13 Tdmc EC
2.4.3.13.1 Description
For H.248 remote media gateway's this allows for the echo cancellation to be set on the interface.
2.4.3.13.2 Definition
Applicable Modes User Type
H.248 remote gateways Read Write
Boolean
2.4.3.14 Audit Timeslot
2.4.3.14.1 Description
This defines how the SVI will audit an MGCP gateway interface. If this is not set then the Audit of
the interface will use the '*' wild card, if it is set to a timeslot value the Audit will use this timeslot
value to audit the entire interface.
2.4.3.14.2 Definition
Applicable Modes User Type
MGCP Media Gateways Read Write
Integer
2.4.3.15 Trunk Group
2.4.3.15.1 Description
End of Life.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 19 of 124
2.5 Signalling Link
2.5.1 Description
Defines an SS7 signalling link of an SS7 interconnect.
2.5.2 Products
SVI-MG | SVI-SG | SVI-MGC | SVI-STP | SVI-9225 | SVI-9220 | SVI-SMSC
2.5.3 Attributes
2.5.3.1 Type
2.5.3.1.1 Description The behaviour type of the resource instance.
2.5.3.1.2 Definition
Applicable Modes User Type
All Read Write
Drop Down List
2.5.3.1.3 Values
Value Description
SS7 Signalling Link SS7 Signalling Link
2.5.3.2 Map
2.5.3.2.1 Description Unique global identifier for the link in the MTPL3 Stack.
2.5.3.2.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.5.3.3 Card
2.5.3.3.1 Description End of Life
2.5.3.4 Interface
2.5.3.4.1 Description Specifies the instance of the interface resource that the signalling link will be located on.
2.5.3.4.2 Definition
Applicable Modes User Type
All but M2PA links Read Write
Resource Identifier
2.5.3.5 Channelled
2.5.3.5.1 Description Specifies the Interface/Channel ID in the M2UA/SLT AS. Must be unique per AS.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 20 of 124
2.5.3.5.2 Definition
Applicable Modes User Type
M2UA and SLT Links Read Write
Integer
2.5.3.6 Trunk
2.5.3.6.1 Description End of Life
2.5.3.7 Timeslot
2.5.3.7.1 Description Specifies the signalling timeslot.
2.5.3.7.2 Definition
Applicable Modes User Type
All but M2PA links Read Write
Integer
2.5.3.8 SLC
2.5.3.8.1 Description Specifies the signalling link code of the signalling link.
2.5.3.8.2 Definition
Applicable Modes User Type
All Links Applied Read Write
Integer
2.5.3.9 Originating
2.5.3.9.1 Description Specifies the instance of the originating point resource to which the signalling link is associated to.
2.5.3.9.2 Definition
Applicable Modes User Type
All Links Read Write
Resource Identifier
2.5.3.10 Linkset
2.5.3.10.1 Description Indicates the instance of the linkset resource for which this linkset is associated to.
2.5.3.10.2 Definition
Applicable Modes User Type
All Links Read Write
Resource Identifier
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 21 of 124
2.5.3.11 Interface ID
2.5.3.11.1 Description As Channel ID – must be set as the same value.
2.5.3.11.2 Definition
Applicable Modes User Type
M2UA and SLT Links Read Write
Integer
2.5.3.12 AS
2.5.3.12.1 Description If M2UA/SLT is used this specifies the AS which the signalling link is associated with.
2.5.3.12.2 Definition
Applicable Modes User Type
M2UA and SLT Links Read Write
Resource Identifier
2.5.3.13 Stream
2.5.3.13.1 Description End of Life
2.5.3.14 SLT Type
2.5.3.14.1 Description Allows setting of the Service Indicator to be Special or Regular Maintenance type (for ANSI MTPL3
only).
2.5.3.14.2 Definition
Applicable Modes User Type
All Links Applied Read Write
Drop Down List
2.5.3.14.3 Values
Value Description
Regular Sets SI value to 1
Special Sets SI value to 2
2.5.3.15 L2 Task
2.5.3.15.1 Description Defines the MTP Layer 2 task that controls the link. Leave blank for default.
2.5.3.15.2 Definition
Applicable Modes User Type
SLT Links Read Write
User String
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 22 of 124
2.5.3.15.3 Values
Value Description
SESSMGR Sets MTP Layer 2 task to be Session Manager
2.5.3.16 Force Normal
2.5.3.16.1 Description Allows the user to define the type of proving used for this signalling link.
2.5.3.16.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.5.3.16.3 Values
Value Description
Standard Will send Emergency Proving for first link aligned in a Linkset and Normal for subsequent
False As Standard
Always Emergency Will send Emergency Proving for all links in a linkset
Always Normal Will send Normal Proving for all links in a linkset
True As Always Normal
2.5.3.17 Set LPO
2.5.3.17.1 Description Used to force a Local Processor Outage MTP L3 Event on the link via the OA&M.
2.5.3.18 Set LPR
2.5.3.18.1 Description Used to force a Local Processor Recovered MTP L3 Event on the link via the OA&M.
2.5.3.19 Inhibit
2.5.3.19.1 Description Used to force an Inhibit MTP L3 Event on the link via the OA&M.
2.5.3.20 Uninhibit
2.5.3.20.1 Description Used to force an Inhibit MTP L3 Event on the link via the OA&M.
2.5.3.21 Debug
2.5.3.21.1 Description Enable enhanced debug for MTPL3 or M2PA.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 23 of 124
2.5.3.21.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Bit Mask Flag
2.5.3.21.3 Values
Value Description
None No debug enabled
M2PA M2PA debug enabled
MTPL3 MTP Layer 3 debug enabled
2.5.3.22 Protocol
2.5.3.22.1 Description End of Life (now set on ASP).
2.5.3.23 SLTM
2.5.3.23.1 Description Enable or disable the sending of Signalling Link Test Messages.
2.5.3.23.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Boolean
2.5.3.23.3 Values
Value Description
True Send SLTM (default)
False Do not send SLTM
2.5.3.24 Variant
2.5.3.24.1 Description Set the protocol variant of the link.
2.5.3.24.2 Definition
Applicable Modes User Type
All Links Read Write
Drop Down List
2.5.3.24.3 Values
Value Description
ITU Sets the standard used to ITU
ANSI Sets the standard used to ANSI
Chinese Sets the standard used to Chinese
TTC Sets the standard used to TTC
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 24 of 124
2.5.3.25 LI Priority Bit
2.5.3.25.1 Description For Japanese only. Allows setting of the Priority Bit on SNM, SNTM and SNTM2 messages.
2.5.3.25.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Boolean
2.5.3.25.3 Values
Value Description
False Normal Priority (default)
True Set priority to 3
2.5.3.26 Transmission Rate
2.5.3.26.1 Description (T1 Links only) Specifies the Signalling Link Transmission rate.
2.5.3.26.2 Definition
Applicable Modes User Type
All TDM Links Read Write
Drop Down List
2.5.3.26.3 Values
Value Description
64K Default value used for most E1 interconnects
56K Used for some T1 interconnects
2MB Used for HSL over E1 interconnects
2.5.3.27 Max Throughput
2.5.3.27.1 Description End of Life
2.5.3.28 Queue Size
2.5.3.28.1 Description End of Life
2.5.3.29 Tx MSU Total
2.5.3.29.1 Description Statistic showing total number of MSU’s sent since system start.
2.5.3.29.2 Definition
Applicable Modes User Type
All Links Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 25 of 124
2.5.3.30 Tx MSU Sec
2.5.3.30.1 Description Statistic showing real-time MSU/Second being sent.
2.5.3.30.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.31 Tx MSU Sec Max
2.5.3.31.1 Description Statistic showing maximum MSU/Second send rate since system start.
2.5.3.31.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.32 Rx MSU Total
2.5.3.32.1 Description Statistic showing total number of MSU’s received since system start.
2.5.3.32.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.33 Rx MSU Sec
2.5.3.33.1 Description Statistic showing real-time MSU/Second being received.
2.5.3.33.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.34 Rx MSU Sec Max
2.5.3.34.1 Description Statistic showing maximum MSU/Second receive rate since system start.
2.5.3.34.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.35 Tx Bits Total
2.5.3.35.1 Description Statistic showing total number of Bit’s sent since system start.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 26 of 124
2.5.3.35.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.36 Tx Bits Sec
2.5.3.36.1 Description Statistic showing real-time Bit/Second being sent
2.5.3.36.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.37 Tx Bits Sec Max
2.5.3.37.1 Description Statistic showing maximum Bit/Second send rate since system start
2.5.3.37.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.38 Rx Bits Total
2.5.3.38.1 Description Statistic showing total number of Bit’s received since system start
2.5.3.38.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.39 Rx Bits Sec
2.5.3.39.1 Description Statistic showing real-time Bit/Second being received
2.5.3.39.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.40 Rx Bits Sec Max
2.5.3.40.1 Description Statistic showing maximum Bit/Second receive rate since system start
2.5.3.40.2 Definition
Applicable Modes User Type
All Links Read Integer
2.5.3.41 M2PA Timer
2.5.3.41.1 Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 27 of 124
Specifies the instance of the m2pa timer resource to which the signalling link will use to override the default timer values.
2.5.3.41.2 Definition
Applicable Modes User Type
All Links Read Write
Resource Identifier
2.6 Circuit
2.6.1 Description
Specifies the SS7 circuits for the SS7 interconnect.
2.6.2 Products SVI-MG | SVI-MGC | SVI-9225 | SVI-9220
2.6.3 Attributes
2.6.3.1 Type
2.6.3.1.1 Description
The behaviour type for the resource instance.
2.6.3.1.2 Definition
Applicable Modes User Type
All Circuits Read Write
Drop Down List
2.6.3.1.3 Values
Value Description
ISUP Circuit For ITU Based ISUP Circuits
ISUP Circuit DI For ITU Based ISUP Circuits with Drop/Insert Routing
IUP Circuit For IUP Circuits
IUP Circuit DI For IUP Circuits with Drop/Insert Routing
ANSI Circuit For ANSI ISUP Circuits
ANSI Circuit DI For ANSI ISUP Circuits with Drop/Insert Routing
ISDN Circuit For ISDN(Q.931) Circuits
2.6.3.2 Map
2.6.3.2.1 Description
Unique ID for mapping Circuit onto the ISUP Stack. Must be unique per Originating Point on the
System.
2.6.3.2.2 Definition
Applicable Modes User Type
ISUP Circuits Read Write
Integer
2.6.3.3 Interface
2.6.3.3.1 Description
Defines the TDM Interface the circuit is assigned to
2.6.3.3.2 Definition
Applicable Modes User Type
All Circuits Read Resource Identifier
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 28 of 124
Write
2.6.3.4 Cic
2.6.3.4.1 Description
Defines the CIC value for the circuit within its Routeset
2.6.3.4.2 Definition
Applicable Modes User Type
All ISUP Circuits Read Write
Integer
2.6.3.5 Controlling
2.6.3.5.1 Description
Defines the controlling end in the case of glare calls.
2.6.3.5.2 Definition
Applicable Modes User Type
All ISUP Circuits Read Write
Drop Down List
2.6.3.5.3 Values
Value Description
Controlling This circuit is controlling
Non Controlling This circuit is not controlling
Odd Controlling This circuit is controlling if its CIC value is Odd
Even Controlling This circuit is controlling if its CIC value is Even
2.6.3.6 Actual Controlling
2.6.3.6.1 Description
Shows the actual controlling status based on the setting defined in the Controlling attribute
2.6.3.6.2 Definition
Applicable Modes User Type
All ISUP Circuits Read User String
2.6.3.6.3 Values
Value Description
Controlling This circuit is controlling
Non Controlling This circuit is not controlling
2.6.3.7 Direction
2.6.3.7.1 Description
Defines if the circuit can accept, make or allow calls in both directions
2.6.3.7.2 Definition
Applicable Modes User Type
All Read Write
Dropdown List
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 29 of 124
2.6.3.7.3 Values
Value Description
Bothway Allow calls in either direction
Incoming Circuit will not be selected for outgoing calls
Outgoing Circuit will not accept any incoming calls
2.6.3.8 Timeslot
2.6.3.8.1 Description
Defines the Media Timeslot on the TDM Interface this Circuit is assigned to.
2.6.3.8.2 Definition
Applicable Modes User Type
All Circuits Read Write
Integer
2.6.3.9 SetupTotal
2.6.3.9.1 Description
Count of number of outgoing call setup attempts made on the circuit. Used in conjunction with
‘COT Frequency’ attribute on ‘SS7 Stack’ resource.
2.6.3.9.2 Definition
Applicable Modes User Type
All ISUP Circuits Read Integer
2.6.3.10 CircuitGroup
2.6.3.10.1 Description
Defines the Circuit Group resource this Circuit is part of (for use with Circuit Group
Blocking/Unblocking).
2.6.3.10.2 Definition
Applicable Modes User Type
All ISUP Circuits Read Write
Resource Identifier
2.6.3.11 Partner
2.6.3.11.1 Description
Defines the Partner Circuit resource when using Drop/Insert Routing.
2.6.3.11.2 Definition
Applicable Modes User Type
All Circuits Read Write
Resource Identifier
2.6.3.12 Stack
2.6.3.12.1 Description
Defines the SS7 Stack resource for the ISUP Routeset.
2.6.3.12.2 Definition
Applicable Modes User Type
All ISUP Circuits Read Write
Resource Identifier
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 30 of 124
2.6.3.13 CallControl
2.6.3.13.1 Description
Defines the Call Control resource assigned to this Circuit.
2.6.3.13.2 Definition
Applicable Modes User Type
All Circuits Read Write
Resource Identifier
2.6.3.14 DCall
2.6.3.14.1 Description
End of Life
2.6.3.15 Datalink
2.6.3.15.1 Description
Defines the ISDN Datalink resource assigned to this Circuit.
2.6.3.15.2 Definition
Applicable Modes User Type
ISDN Circuits Read Write No-Default
Resource Identifier
2.6.3.16 COT Success
2.6.3.16.1 Description
Time at which the circuit last had a successful COT Test.
2.6.3.16.2 Definition
Applicable Modes User Type
All ISUP Circuits Read String
2.6.3.17 CC Status
2.6.3.17.1 Description
Displays the current call control status of the Circuit.
2.6.3.17.2 Definition
Applicable Modes User Type
All Circuits Read User String
2.6.3.17.3 Values
Value Description
CC_IDLE Idle. Circuit record not in use.
IC_WAIT_COT Incoming call requested COT test. Waiting for COT message with success for failure.
IC_WAIT_DIGITS Waiting to collect all digits from subsequence SAM messages for overlap call.
IC_SEIZE Circuit is in use for incoming call but call has not yet been routed.
IC_WAIT_ACCEPTED Incoming Call Wait for Accepted message.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 31 of 124
Waiting for Accepted message from outgoing call
IC_WAIT_ANSWER Incoming Call Wait for Answer message. Waiting for Answer message from outgoing call
IC_WAIT_BWD_MSG Incoming Call Wait for backward message. Waiting for any response from outgoing call.
IC_CCR_TEST Incoming Call. Running CCR test.
IC_COLLECT_DIGITS Waiting to collect all digits from subsequence SAM messages for overlap call.
IC_SUSPEND Suspended Incoming Call
CC_ANSWER Answered Call
CC_WAIT_CHANNEL_FREE Waiting for Channel Free message before clearing circuit
CC_WAIT_TRANSIT_CHANNEL_FREE Waiting for Channel Free message before clearing circuit
CC_WAIT_BWD_CLEAR Waiting for backwards clear message
CC_WAIT_DISCRESP Waiting for response to disconnect request
CC_WAIT_TRANSIT_DISCRESP Waiting for response to disconnect request
CC_WAIT_BWD_CLEAR_DISCRESP Waiting for response to disconnect request from a backwards clear message
CC_IDLE_WAIT_DISCRESP Waiting for response to disconnect request before going IDLE
IC_SEIZE_WAIT_DISCRESP Waiting for response to disconnect request whilst attempting to route
OG_WAIT_CALL_PROGRESS Outgoing Call Wait for Process message. Waiting for Process message from outgoing call
OG_WAIT_ANSWER Outgoing call Wait for Answer. Waiting for ISUP ANM or ISDN CONNECT message.
OG_WAIT_BWD_MSG Outgoing Call Wait for backward message. Waiting for any response from outgoing call.
OG_WAIT_DIGITS Outgoing call. Sent initial IAM message but may be further digits in subsequent SAMs to be received
OG_WAIT_SETUP_ACK Outgoing Call Waiting for acknowledge to Setup message.
OG_SUSPEND Suspended Outgoing Call
OG_WAIT_ACCEPTED Outgoing call Wait for Answer. Waiting for ISUP ACM or ISDN ALERTING message.
OG_CCR_TEST Outgoing Call. Running CCR test.
IC_WAIT_SPEECH_PATH_CONNECT Incoming Call. Waiting for media connection to be setup
OG_WAIT_SPEECH_PATH_CONNECT Outgoing Call. Waiting for media connection to be setup
IC_SEIZE_GET_ROUTE Waiting for response to external routing request (e.g. SQL server)
CC_TRANSFER_NOTIFY Call is being transferred. In this state whilst negotiating with third leg.
IC_WAIT_CNAM_RSP Incoming call. Waiting for response to a CNAM, LNP, 800 or LIDB
IC_PLAY_ANN_PENDING_CLEAR Incoming Call. Playing announcement before clearing
IC_WAIT_TIMER_EXPIRY_B4_PLAY_ANN Incoming Call. Waiting for timer to expire before the SVI can play an announcement
IC_WAIT_SPCH_PTH_CNCT_B4_PLAY_ANN Incoming Call. Waiting for the media path to be setup before the SVI can play an announcement
IC_WAIT_SPCH_CNCT_B4_DISC Incoming Call. Waiting for media connection to be setup, then will disconnect. Occurs when call is cleared whilst media connection is being
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 32 of 124
setup
OG_WAIT_SPCH_CNCT_B4_DISC Outgoing Call. Waiting for media connection to be setup, then will disconnect. Occurs when call is cleared whilst media connection is being setup
IC_WAIT_TIMER_EXPIRY_B4_PLAY_ANN_OG_SETUP Incoming Call. Waiting for the media path to be setup before the SVI can play an announcement before sending Outgoing call setup message
IC_WAIT_SPCH_PATH_B4_PLAY_ANN_OG_SETUP Incoming Call. Waiting for the media path to be setup before the SVI can play an announcement before sending Outgoing call setup message
IC_WAIT_TIMER_AND_SPCH_CNT_B4_PLAY_ANN Incoming Call. Waiting for timer to expire before for the media path to be setup before the SVI can play an announcement
IC_PLAY_ANN_B4_OG_SETUP Incoming Call. Playing announcement before sending Outgoing call setup message
IC_PARTIAL_MATCH Incoming Call. Call has provided a partial match in the routing for an overlap call which has not received all digits.
OG_PLAY_ANN_ALLOCATED Outgoing Call.
CC_LI_ALLOCATED Lawful Intercept call.
CC_COT_TEST COT Test in progress
IC_SEIZE_TRANSLATE_NUMBER_REQ Incoming Call. Waiting for response from a number translation request
CC_THROTTLED Call throttled at ISUP, will revert other state when
2.6.3.18 Initialise
2.6.3.18.1 Description
End Of Life
2.6.3.19 Block State
2.6.3.19.1 Description
Displays the current status of the circuit blocks.
2.6.3.19.2 Definition
Applicable Modes User Type
All ISUP Circuits Read Write
User String
2.6.3.19.3 Values
Value Description
IDLE Available for use
MBLK Maintenance Blocked
LBLK Locally Blocked
RBLK Remotely Blocked
MBLK-RBLK Maintenance and Remotely Blocked
LBLK-RBLK Locally and Remotely Blocked
MBLK-LBLK Maintenance and Locally Blocked
MBLK-LBLK-RBLK Maintenance, Locally and Remotely Blocked
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 33 of 124
2.6.3.20 Options
2.6.3.20.1 Description
Circuit resource specific options.
2.6.3.20.2 Definition
Applicable Modes User Type
All Circuits Read Write No-Default
Bit Mask Flag
2.6.3.20.3 Values
Value Description
SNMP-Trap Generate SNMP traps for this resource.
UCIC Indicates that a UCIC message was received on this circuit from far end.
2.6.3.21 send CVT
2.6.3.21.1 Description
Generate a CVT message on this circuit.
2.6.3.22 Send CQM
2.6.3.22.1 Description
Generate a CQM message on this circuit.
2.7 Circuit Group
2.7.1 Description
Resource used to group ISUP Circuits together for the purposes of Group Block/Reset.
2.7.2 Products
SVI-MG | SVI-MGC | SVI-9225 | SVI-9220.
2.7.3 Attributes
2.7.3.1 Type
2.7.3.1.1 Description
The behaviour type for the resource instance.
2.7.3.1.2 Definition
Applicable Modes User Type
All Read Write
Dropdown List
2.7.3.1.3 Values
Value Description
ISUP Circuit Group Defines as ISUP Circuit Group Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 34 of 124
2.7.3.2 Card
2.7.3.2.1 Description
End of Life.
2.7.3.3 Map
2.7.3.3.1 Description
End of Life.
2.7.3.4 TupFlags
2.7.3.4.1 Description
End Of Life.
2.7.3.5 Priority
2.7.3.5.1 Description
End Of Life.
2.7.3.6 Tcg
2.7.3.6.1 Description
Timer between receipt of BLO/UBL and sending CGB/CGU.
2.7.3.6.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.7.3.7 Start Circuit
2.7.3.7.1 Description
First Circuit in the Group.
2.7.3.7.2 Definition
Applicable Modes User Type
All Read Write No-Default
Resource Identifier
2.7.3.8 Last Circuit
2.7.3.8.1 Description
Last Circuit in the Group.
2.7.3.8.2 Definition
Applicable Modes User Type
All Read Write No-Default
Resource Identifier
2.7.3.9 Range
2.7.3.9.1 Description
Number of circuit in the group. Set automatically based on Start/Last values.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 35 of 124
2.7.3.9.2 Definition
Applicable Modes User Type
All Read
Integer
2.7.3.10 Stack
2.7.3.10.1 Description
The SS7 Stack resource the circuits are assigned to.
2.7.3.10.2 Definition
Applicable Modes User Type
All Circuit Groups Read Write
Resource Identifier
2.7.3.11 Interface
2.7.3.11.1 Description
The TDM Interface the circuits are assigned to.
2.7.3.11.2 Definition
Applicable Modes User Type
All Circuit Groups Read Write
Resource Identifier
2.7.3.12 CGRS State
2.7.3.12.1 Description
Sets the behaviour regarding Circuit Group Reset messages in this Circuit Group. Updated
automatically based on Circuit Group state.
2.7.3.12.2 Definition
Applicable Modes User Type
All Circuit Groups Read Drop Down List
2.7.3.12.3 Values
Value Description
Can Send Can send CGRS
Cant Send Cannot send CGRS
Never Send Never send CGRS
2.8 Originating Point
2.8.1 Description
Defines the originating point of the SS7 interconnect.
2.8.2 Products SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG
2.8.3 Attributes
2.8.3.1 Type
2.8.3.1.1 Description
The behaviour type for the resource instance.
2.8.3.1.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 36 of 124
All Read Write
Drop Down List
2.8.3.1.3 Values
Value Description
SS7 Originating Point Defines as SS7 Originating Point
SIGTRAN Originating Point As SS7 Originating Point
2.8.3.2 Protocol
2.8.3.2.1 Description
Sets the base standard for the originating point.
2.8.3.2.2 Definition
Applicable Modes User Type
All Applied Read Write
Drop Down List
2.8.3.2.3 Values
Value Description
ETSI Sets base as ETSI
ITU Sets base as ITU
ANSI Sets bases as ANSI
TUP Sets base as TUP
TTC Sets base as TTC
China Sets base as China
2.8.3.3 STPMode
2.8.3.3.1 Description
Sets the Originating Point STP Mode for special point code routing/presentation scenarios.
2.8.3.3.2 Definition
Applicable Modes User Type
All Applied Read Write
Drop Down List
2.8.3.3.3 Values
Value Description
None No special mode applied
Partial Partial Point Code mode applied
Full Full Point Code mode applied
2.8.3.4 Pointcode
2.8.3.4.1 Description
Contains the originating pointcode (decimal). 2.8.3.4.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 37 of 124
2.8.3.5 Ni
2.8.3.5.1 Description
Network Indicator of the route
2.8.3.5.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.8.3.5.3 Values
Value Description
0 International
1 International (Spare)
2 National
3 National (Spare)
2.8.3.6 Debug
2.8.3.6.1 Description
End Of Life
2.8.3.7 Info
2.8.3.7.1 Description
Displays detailed MTP Layer 3 info about Originating Point in OAM (not available in SVI_MS)
2.8.3.7.2 Definition
Applicable Modes User Type
All Write N/A
2.8.3.8 Setdebug
2.8.3.8.1 Description
End of Life
2.8.3.9 Retrieval Persistent
2.8.3.9.1 Description
End of Life
2.8.3.10 L3Timers
2.8.3.10.1 Description
Defines the MTPL3 Timer Resource in the case that the default timers need to be overridden.
2.8.3.10.2 Definition
Applicable Modes User Type
All Applied Read Write
Resource Identifier
2.8.3.11 MTP Route Via DPC Pointcodes
2.8.3.11.1 Description
For the STP if set to Override the OPC and DPC for the outgoing message will be overwritten with
the point code for the destination and the point code of the originating point. If set to Leave then
the incoming point codes will be used (unless they have been translated).
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 38 of 124
The Destination Point value for this flag will take preference unless set to Ignore or not set.
2.8.3.11.2 Definition
Applicable Modes User Type
All Read Write
Byte
2.8.3.11.3 Values
Value Description
0 Ignore
1 Leave
2 Override
2.9 Destination Point
2.9.1 Description
Defines the destination points of an SS7 signalling interconnect.
2.9.2 Products SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG
2.9.3 Attributes
2.9.3.1 Type
2.9.3.1.1 Description
The behaviour type for the resource instance.
2.9.3.1.2 Definition
Applicable Modes User Type
All Read Write
Drop Down List
2.9.3.1.3 Values
Value Description
SS7 Destination Point Set as type SS7 Destination Point
IPSP Destination Point For use with M3UA IPSP Interconnects
ISUP Destination Point As SS7 Destination Point
2.9.3.2 Originating
2.9.3.2.1 Description
Specifies the instance of the originating point that the destination is associated to. 2.9.3.2.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.9.3.3 Pointcode
2.9.3.3.1 Description
Contains the pointcode of the destination point (decimal). 2.9.3.3.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 39 of 124
All Applied Read Write
Integer
2.9.3.4 Ni
2.9.3.4.1 Description
Contains the Network Indicator of the destination point. 2.9.3.4.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.9.3.4.3 Values
Value Description
0 International
1 International (Spare)
2 National
3 National (Spare)
2.9.3.5 Primary
2.9.3.5.1 Description
This indicates the primary linkset that the destination is connected to 2.9.3.5.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.9.3.6 Secondary
2.9.3.6.1 Description
If a linkset is connected to a secondary linkset this attribute contains the linkset resource instance which is the secondary route. 2.9.3.6.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.9.3.7 Loadshare
2.9.3.7.1 Description
To load share between routes.
2.9.3.7.2 Definition
Applicable Modes User Type
All Read Write
Boolean
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 40 of 124
2.9.3.8 Transfer Report
2.9.3.8.1 Description
The Linksets which will have TFX messages sent on should this Destination Point change state.
2.9.3.8.2 Definition
Applicable Modes User Type
All Read Resource Identifier
2.9.3.9 Sls
2.9.3.9.1 Description
Used for SCCP Load sharing. Updated automatically.
2.9.3.9.2 Definition
Applicable Modes User Type
All Read Integer
2.9.3.10 Clink
2.9.3.10.1 Description
The Linkset which is the C-Link for this Destination Point
2.9.3.10.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.9.3.11 Max Msg/s
2.9.3.11.1 Description
Statistic showing the maximum messages/second since system start
2.9.3.11.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.9.3.12 Msg/s
2.9.3.12.1 Description
Statistic showing the real-time messages/second
2.9.3.12.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 41 of 124
2.9.3.13 RQue
2.9.3.13.1 Description
Used for MTPL3 throttling. Updated automatically.
2.9.3.13.2 Definition
Applicable Modes User Type
All Read No-Default
Integer
2.9.3.14 ASP
2.9.3.14.1 Description
End of Life.
2.9.3.15 AS
2.9.3.15.1 Description
For M3UA the AS resource this Destination Point is available via.
2.9.3.15.2 Definition
Applicable Modes User Type
All Read Write
Resource identifier
2.9.3.16 MTP Route Via DPC Pointcodes
2.9.3.16.1 Description
For the STP if set to Override the OPC and DPC for the outgoing message will be overwritten with
the point code for the destination and the point code of the originating point. If set to Leave then
the incoming point codes will be used (unless they have been translated)
2.9.3.16.2 Definition
Applicable Modes User Type
All Read Write
Byte
2.9.3.16.3 Values
Value Description
0 Ignore
1 Leave
2 Override
2.10 Linkset
2.10.1 Description Defines the Linkset or Adjacent point of the SS7 interconnect.
2.10.2 Products
SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 42 of 124
2.10.3 Attributes
2.10.3.1 Type
2.10.3.1.1 Description
The behaviour type for the resource instance.
2.10.3.1.2 Definition
Applicable Modes User Type
All Read Write
Drop Down List
2.10.3.1.3 Values
Value Description
SS7 Linkset Defines as SS7 Linkset
2.10.3.2 Map
2.10.3.2.1 Description
End of Life
2.10.3.3 Originating
2.10.3.3.1 Description
Specifies the instance of the originating point resource that the linkset is associated to.
2.10.3.3.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.10.3.4 Pointcode
2.10.3.4.1 Description
Pointcode of the adjacent point (decimal).
2.10.3.4.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.10.3.5 Ni
2.10.3.5.1 Description
Network indicator of the adjacent point.
2.10.3.5.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.10.3.5.3 Values
Value Description
0 International
1 International (Spare)
2 National
3 National (Spare)
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 43 of 124
2.10.3.6 Combined
2.10.3.6.1 Description
If the linkset is part of a combined linkset this value is set to the resource instance of the combined linkset, else it is set to the value of this linksets instance.
2.10.3.6.2 Definition
Applicable Modes User Type
All Applied Read Write No-Default
Resource Link
2.10.3.7 TFx Required
2.10.3.7.1 Description
If true Destination Points will not be set as available via this Linkset until a TFA is explicitly
received after the Linkset is available.
2.10.3.7.2 Definition
Applicable Modes User Type
All Read Write
Boolean
2.10.3.7.3 Values
Value Description
False Destination Points are presumed available when Linkset is available
True Destination Points are presumed unavailable until notified by TFA
2.10.3.8 Transfer Report
2.10.3.8.1 Description
A list of destination point resources the linkset is interested to know the status through TFP/TFA
mechanism.
2.10.3.9 Add MTP Routes
2.10.3.9.1 Description
Attach MTP Route resources which will be used for MTP Layer 3 routing rules on this linkset.
2.10.3.9.2 Definition
Applicable Modes User Type
All Read Write No-Default
Resource Link
2.10.3.10 MTP CDR
2.10.3.10.1 Description
End of Life
2.10.3.11 Tx MSU Total
2.10.3.11.1 Description Statistic showing total number of MSU’s sent since system start.
2.10.3.11.2 Definition
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 44 of 124
Applicable Modes User Type
All Links Read Integer
2.10.3.12 Tx MSU Sec
2.10.3.12.1 Description Statistic showing real-time MSU/Second being sent.
2.10.3.12.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.13 Tx MSU Sec Max
2.10.3.13.1 Description Statistic showing maximum MSU/Second send rate since system start.
2.10.3.13.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.14 Rx MSU Total
2.10.3.14.1 Description Statistic showing total number of MSU’s received since system start.
2.10.3.14.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.15 Rx MSU Sec
2.10.3.15.1 Description Statistic showing real-time MSU/Second being received.
2.10.3.15.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.16 Rx MSU Sec Max
2.10.3.16.1 Description Statistic showing maximum MSU/Second receive rate since system start.
2.10.3.16.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.17 Tx Bits Total
2.10.3.17.1 Description Statistic showing total number of Bit’s sent since system start.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 45 of 124
2.10.3.17.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.18 Tx Bits Sec
2.10.3.18.1 Description Statistic showing real-time Bit/Second being sent.
2.10.3.18.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.19 Tx Bits Sec Max
2.10.3.19.1 Description Statistic showing maximum Bit/Second send rate since system start.
2.10.3.19.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.20 Rx Bits Total
2.10.3.20.1 Description Statistic showing total number of Bit’s received since system start.
2.10.3.20.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.21 Rx Bits Sec
2.10.3.21.1 Description Statistic showing real-time Bit/Second being received.
2.10.3.21.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.22 Rx Bits Sec Max
2.10.3.22.1 Description Statistic showing maximum Bit/Second receive rate since system start.
2.10.3.22.2 Definition
Applicable Modes User Type
All Links Read Integer
2.10.3.23 COO Bis
2.10.3.23.1 Description
End Of Life.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 46 of 124
2.10.3.24 IC L3Label
2.10.3.24.1 Description
Range of L3 Label resources to examine when routing messages from this Linkset.
2.10.3.24.2 Definition
Applicable Modes User Type
All links Read / Write String
2.10.3.24.3 Values
Value Description
Range of Resource instances
2.10.3.25 OG L3Label
2.10.3.25.1 Description
Range of L3 Label resources to examine when routing messages to this Linkset.
2.10.3.25.2 Definition
Applicable Modes User Type
All Links Read / Write String
2.10.3.25.3 Values
Value Description
Range of Resource instances
2.10.3.26 M3UA AS
2.10.3.26.1 Description
Specifies the instance of the AS resource that the linkset is associated to. Only applicable to M3UA configuration.
2.10.3.26.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.10.3.27 SSME XML
2.10.3.27.1 Description
Specifies the instance of the XML resource that the linkset is associated to. Used to apply an xml based configuration for message routing and manipulation.
2.10.3.27.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.10.3.28 Tx Bits Throttle
2.10.3.28.1 Description Statistic showing real-time Bit/Second throttling.
2.10.3.28.2 Definition
Applicable Modes User Type
All Linksets Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 47 of 124
2.10.3.29 Tx MSU Throttle
2.10.3.29.1 Description Statistic showing real-time MSU/Second throttling.
2.10.3.29.2 Definition
Applicable Modes User Type
All Linksets Read Integer
2.10.3.30 Tx Congestion
2.10.3.30.1 Description Statistic showing number of times congestion was entered.
2.10.3.30.2 Definition
Applicable Modes User Type
All Linksets Read Integer
2.10.3.31 Tx Failure
2.10.3.31.1 Description Statistic showing number of failures.
2.10.3.31.2 Definition
Applicable Modes User Type
All Linksets Read Integer
2.10.3.32 Routing Failures
2.10.3.32.1 Description Statistic showing number of failures happened while attempting to process an incoming packet.
2.10.3.32.2 Definition
Applicable Modes User Type
All Linksets Read Integer
2.10.3.33 Rx UDTS
2.10.3.33.1 Description Statistic showing number of UDTS messages received.
2.10.3.33.2 Definition
Applicable Modes User Type
All Linksets Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 48 of 124
2.11 SS7 Stack
2.11.1 Description
Resource used to define the Routset and Layer 4 (ISUP/SCCP) capabilities.
2.11.2 Products
SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG.
2.11.3 Attributes
2.11.3.1 Type
2.11.3.1.1 Description The behaviour type of the resource instance.
2.11.3.1.2 Definition
Applicable Modes User Type
All Read Write
Dropdown List
2.11.3.1.3 Values
Value Description
ISUP Stack For ITU/ETSI based variants of ISUP
IUP Stack For IUP(BTNUP)
TUP Stack For TUP
ANSI Stack For ANSI ISUP
SCTP For SCCP Passthrough to M3UA Mode
SCCP Router Stack For SCCP Routing Mode
2.11.3.2 Map
2.11.3.2.1 Description End Of Life.
2.11.3.3 MTPL3
2.11.3.3.1 Description Defines if the internal MTP Layer 3 stack is to be used, or external or M3UA (no MTP Layer 3).
2.11.3.3.2 Definition
Applicable Modes User Type
All Read Write
Dropdown List
2.11.3.3.3 Values
Value Description
Internal Use the Internal Stack
External Use an External Stack (no longer used)
M3UA Use M3UA
2.11.3.4 MTPL4
2.11.3.4.1 Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 49 of 124
Defines if the internal ISUP stack is to be used or external.
2.11.3.4.2 Definition
Applicable Modes User Type
All ISUP Read Write
Dropdown List
2.11.3.4.3 Values
Value Description
Internal Use Internal Stack
External Use External Stack (No longer used)
2.11.3.5 Originating Point
2.11.3.5.1 Description Links to the Originating Point Resource for the routeset.
2.11.3.5.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.11.3.6 Destination Point
2.11.3.6.1 Description Links to the Destination Point Resource for the routeset.
2.11.3.6.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.11.3.7 IP
2.11.3.7.1 Description End Of Life.
2.11.3.8 AS
2.11.3.8.1 Description For SCTP Type sets the M3UA AS the SCCP will pass through to.
2.11.3.8.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.11.3.9 SIO
2.11.3.9.1 Description Sets the Service Indicator for the Stack.
2.11.3.9.2 Definition
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 50 of 124
Applicable Modes User Type
All Read Write
Integer
2.11.3.9.3 Values
Value Description
3 SCCP
5 ISUP
2.11.3.10 IUP ISDN
2.11.3.10.1 Description Sets the behaviour for ISUP call types.
2.11.3.10.2 Definition
Applicable Modes User Type
All IUP Read Write
Dropdown List
2.11.3.10.3 Values
Value Description
Map ISDN Map ISDN (Default)
Reject Reject the call
Map Telephony Map Telephony
2.11.3.11 IUP ACI Request
2.11.3.11.1 Description Sets the type of information requested when ACI is sent.
2.11.3.11.2 Definition
Applicable Modes User Type
All IUP Read Write
Dropdown List
2.11.3.11.3 Values
Value Description
None None
Full Calling Full Calling Number
Full Forward Full Forwarding Number
Full Calling and Forward
Full Calling and Forwarding Numbers
Presentation Presentation Number
Presentation and Full Presentation and Full Calling Numbers
Presentation and Forward
Presentation and Forwarding Numbers
Presentation and Forward and Full
Presentation, Full Calling and Forwarding Numbers
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 51 of 124
2.11.3.12 IUP ASUI Type
2.11.3.12.1 Description Sets the type of ASUI for IUP.
2.11.3.12.2 Definition
Applicable Modes User Type
All IUP Read Write
Dropdown List
2.11.3.12.3 Values
Value Description
Type 1 Full Full numbers requested (default)
Type 2 Partial Partial numbers requested
2.11.3.13 IUP No OLI
2.11.3.13.1 Description Set behaviour for OLI in IUP.
2.11.3.13.2 Definition
Applicable Modes User Type
All IUP Read Write
Dropdown List
2.11.3.13.3 Values
Value Description
Request OLI Request OLI (default)
Send Partial Request partial OLI
Send No OLI Do not send OLI
2.11.3.14 ISUP T13
2.11.3.14.1 Description Set ISUP Timer 13 (default 300 second).
2.11.3.14.2 Definition
Applicable Modes User Type
All ISUP Read Write
Integer
2.11.3.15 ISUP T21
2.11.3.15.1 Description Set ISUP Timer 21 (default 20 second).
2.11.3.15.2 Definition
Applicable Modes User Type
All ISUP Read Write
Integer
2.11.3.16 ISUP T24
2.11.3.16.1 Description Set ISUP Timer 24 (default 20 second).
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 52 of 124
2.11.3.16.2 Definition
Applicable Modes User Type
All ISUP Read Write
Integer
2.11.3.17 ISUP T25
2.11.3.17.1 Description Set ISUP Timer 25 (default 1 second).
2.11.3.17.2 Definition
Applicable Modes User Type
All ISUP Read Write
Integer
2.11.3.18 ISUP Timers
2.11.3.18.1 Description Link to Timer resource for setting of all ISUP Timers.
2.11.3.18.2 Definition
Applicable Modes User Type
All ISUP Read Write
Resource Identifier
2.11.3.19 PCLI
2.11.3.19.1 Description Set Partial CLI to be presented if requested by network.
2.11.3.19.2 Definition
Applicable Modes User Type
All IUP Read Write
Integer
2.11.3.20 Protocol
2.11.3.20.1 Description Set the specific ISUP protocol used.
2.11.3.20.2 Definition
Applicable Modes User Type
All ISUP Read Write
Dropdown List
2.11.3.20.3 Values
Value Description
ITU White Book ITU White Book
ITU Blue Book ITU Blue Book
ANSI ANSI
French SPIROU French SPIROU
Uk isup Uk isup
Finnish ISUP Finnish ISUP
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 53 of 124
2.11.3.21 COTFrequency
2.11.3.21.1 Description Set the frequency of how often a COT test should be preformed per number of call attempts.
2.11.3.21.2 Definition
Applicable Modes User Type
All ISUP Read Write
Integer
2.11.3.22 Network Appearance
2.11.3.22.1 Description End Of Life
2.11.3.23 Options
2.11.3.23.1 Description Set specific options on the SS7 Stack.
2.11.3.23.2 Definition
Applicable Modes User Type
All Read Write No-Default
Bit Mask Flag
2.11.3.23.3 Values
Value Description
None None
Ignore-Process End Of Life
SS7 Accelerated Assumes Local Blocks are available without UBL/UBA exchange
Route SST Route SCCP SST messages rather then terminate them
Include Appearance End Of Life
2.11.3.24 Service
2.11.3.24.1 Description Set the high level service type.
2.11.3.24.2 Definition
Applicable Modes User Type
All SCCP Read Write
Dropdown List
2.11.3.24.3 Values
Value Description
Map Map
TCAP TCAP
2.11.3.25 ACC DrateStart
2.11.3.25.1 Description Sets the Start Percentage for decreasing traffic rate (default 5).
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 54 of 124
2.11.3.25.2 Definition
Applicable Modes User Type
All UK ISUP Read Write
Integer
2.11.3.26 ACC DrateEnd
2.11.3.26.1 Description Sets the maximum percentage for decreasing traffic rate (default 10).
2.11.3.26.2 Definition
Applicable Modes User Type
All UK ISUP Read Write
Integer
2.11.3.27 ACC Drate
2.11.3.27.1 Description Current percentage being used to decrease traffic rate.
2.11.3.27.2 Definition
Applicable Modes User Type
All UK ISUP Read No-Secure
Integer
2.11.3.28 ACC Irate
2.11.3.28.1 Description Percentage to be being used to increase traffic rate (default 10).
2.11.3.28.2 Definition
Applicable Modes User Type
All UK ISUP Read Write
Integer
2.11.3.29 ACC Max
2.11.3.29.1 Description Calls per second rate at which to trigger ACC.
2.11.3.29.2 Definition
Applicable Modes User Type
All UK ISUP Read Write
Integer
2.11.3.30 ACC Min
2.11.3.30.1 Description Calls per second rate at which to allow traffic increase (disable ACC).
2.11.3.30.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 55 of 124
All UK ISUP Read Write
Integer
2.11.3.31 ACC Throttle
2.11.3.31.1 Description Current call/second throttle applied to outgoing traffic.
2.11.3.31.2 Definition
Applicable Modes User Type
All UK ISUP Read No-Secure
Integer
2.11.3.32 ACC Congestion
2.11.3.32.1 Description Flag to show if ACC is currently being applied.
2.11.3.32.2 Definition
Applicable Modes User Type
All UK ISUP Read No-Secure
Boolean
2.11.3.33 ACC Apply
2.11.3.33.1 Description Flag to configure if ACC should be used on this route.
2.11.3.33.2 Definition
Applicable Modes User Type
All UK ISUP Read Write
Boolean
2.11.3.34 ACC Tabate
2.11.3.34.1 Description Configurable Timer that monitors if congestion has abated and ACC can be removed. This requires
consecutive samples to be below the min REL rate for time Tabate.
2.11.3.34.2 Definition
Applicable Modes User Type
All UK ISUP Read Write
Integer
2.11.3.35 ACC Sample
2.11.3.35.1 Description Result of the current sample.
2.11.3.35.2 Definition
Applicable Modes User Type
All UK ISUP Read No-Secure
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 56 of 124
2.11.3.36 ACC Statistics
2.11.3.36.1 Description Link to Statistics resource to allow more monitoring.
2.11.3.36.2 Definition
Applicable Modes User Type
All UK ISUP Read Write
Resource Identifier
2.11.3.37 Service GT
2.11.3.37.1 Description Sets the calling party digits for the SCCP and the GMSC Address for SRI Lookups only
2.11.3.37.2 Definition
Applicable Modes User Type
SRI Lookup Read Write
User String
2.11.3.38 Pass-Through-TCAP
2.11.3.38.1 Description For InitialDp allows the SCCP Data to be passed through the TCAP Stack unchanged
2.11.3.38.2 Definition
Applicable Modes User Type
Pass-Through-TCAP Read Write
Byte
2.11.3.39 CAP SSN
2.11.3.39.1 Description List of Subsystem Numbers (SSN) that needs to be considered as CAMEL Subsystem numbers.
2.11.3.39.2 Definition
Applicable Modes User Type
CAP SSN Read Write
Integer
2.11.3.40 CAMEL Phases
2.11.3.40.1 Description Set the supported CAMEL Phases value to be sent in Send Routing Info (SRI) request sent out.
2.11.3.40.2 Definition
Applicable Modes User Type
All SCCP doing SRI Read Write
Dropdown List
2.11.3.40.3 Values
Value Description
None CamelInfo parameter not sent in SRI request
Phase 1 CAMEL Phase 1 support indication
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 57 of 124
Phase 2 CAMEL Phase 1 and 2 support indication
Phase 3 CAMEL Phase 1,2 and 3 support indication
Phase 4 CAMEL Phase 1,2,3 and 4 support indication
2.11.3.41 INAP Application Context
2.11.3.41.1 Description Set the application context value that needs to be used in INAP Initial DP message sent out.
2.11.3.41.2 Definition
Applicable Modes User Type
All SCCP doing INAP IDP Read Write
Free text application context
2.11.3.42 Ignore API Client
2.11.3.42.1 Description Enable routing of all messages on this stack to the callcontrol task ignoring any API Client tasks
available to process the message.
2.11.3.42.2 Definition
Applicable Modes User Type
All SCCP Read Write
Boolean
2.12 MTP Route
2.12.1 Description
Resource used to define the Routeset and Layer 4 (ISUP/SCCP) capabilities.
2.12.2 Products
SVI-STP
2.12.3 Attributes
2.12.3.1 OPC
2.12.3.1.1 Description Is the OPC present.
2.12.3.1.2 Definition
Value Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 58 of 124
Match to defined
Present The OPC is expected to be Present
Not Present The OPC is expected not to be present
2.12.3.2 DPC
2.12.3.2.1 Description Is the DPC present.
2.12.3.2.2 Definition
Value Description
Match to defined
Present The DPC is expected to be Present
Not Present The DPC is expected not to be present
2.12.3.3 NI
2.12.3.3.1 Description
Network Indicator of the MTP route.
2.12.3.3.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.12.3.3.3 Values
Value Description
0 International
1 International (Spare)
2 National
3 National (Spare)
2.12.3.4 SIO
2.12.3.4.1 Description Sets the Service Indicator for the MTP route.
2.12.3.4.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.12.3.4.3 Values
Value Description
3 SCCP
5 ISUP
2.12.3.5 Linkset
2.12.3.5.1 Description Indicates the instance of the linkset resource for which this linkset is associated to.
2.12.3.5.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 59 of 124
All Links Read Write
Resource Identifier
2.12.3.6 L3Message
2.12.3.6.1 Description The value of the message you wish to match, number is an integer but must be converted to hex.
2.12.3.6.2 Definition
Applicable Modes User Type
All Links Read Write
Integer
2.12.3.7 Set_OPC
2.12.3.7.1 Description
Specifies the instance of the originating point that the destination is associated to. 2.12.3.7.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.12.3.8 Set_DPC
Specifies the instance of the destination point that the destination is associated to.
2.12.3.8.1 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.12.3.9 Set_NI
2.12.3.9.1 Description
Network Indicator of the route.
2.12.3.9.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.12.3.10 Route
The Linkset which should be used to Route to.
(When in loadshare) - The route which should be used when the SLC is even.
2.12.3.11 Destination
The destination Point you wish to Route to.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 60 of 124
2.12.3.12 Secondary
The linkset which should be used if the primary is unavailable.
(When in loadshare) - The route which should be used when the SLC is odd.
2.12.3.13 AS Route
2.12.3.13.1 Description The M3UA AS to route to (primary) (when in loadshare) – route used when SLC is even.
2.12.3.13.2 Definition
Applicable Modes User Type
M3UA Links Read Write
Resource Identifier
2.12.3.14 AS Route Sec
2.12.3.14.1 Description The M3UA AS to route to (secondary) (when in loadshare) – route used when SLC is odd.
2.12.3.14.2 Definition
Applicable Modes User Type
M3UA Links Read Write
Resource Identifier
2.12.3.15 Layer 4 Db
End Of Life.
2.12.3.16 Call Control
Defines the Call Control resource assigned to this Circuit.
2.12.3.16.1 Definition
Applicable Modes User Type
All Circuits Read Write
Resource Identifier
2.12.3.17 Options
2.12.3.17.1 Definition
Applicable Modes User Type
All Read Write No-Default
Bit Mask Flag
2.12.3.17.2 Values
Value Description
Loadshare Use load sharing between Route and secondary
None None
SNMP-Trap If the resource changes state, an SNMP trap will be sent to the address configured on the debug resource.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 61 of 124
2.12.3.18 In CIC Low
2.12.3.18.1 Description
Matches all ISUP CIC’s above this number.
2.12.3.18.2 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.12.3.19 In CIC High
Matches all ISUP CIC’s below this number.
2.12.3.19.1 Definition
Applicable Modes User Type
All Applied Read Write
Integer
2.12.3.20 Out CIC low
Only used when “In CIC Low” configured.
Set’s the outgoing CIC to be as follows:
Out CIC low + (In CIC - In CIC low).
2.12.3.21 Out CIC High
End Of Life.
2.13 SCTP
2.13.1 Description
Creates and maintains an SCTP socket for the use of M3UA/M2PA/M2UA etc.
2.13.2 Products
SVI-MG | SVI-MGC | SVI-STP | SVI-SMSC | SVI-SG.
2.13.3 Attributes
2.13.3.1 Type
2.13.3.1.1 Description The behaviour type of the resource instance.
2.13.3.1.2 Definition
Applicable Modes User Type
All Read Write
Resource
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 62 of 124
2.13.3.1.3 Values
Value Description
SCTP SCTP Socket
2.13.3.2 ASP
2.13.3.2.1 Description The ASP Resource associated with this SCTP socket.
2.13.3.2.2 Definition
Applicable Modes User Type
All Read Write
Resource Identifier
2.13.3.3 Local Port
2.13.3.3.1 Description The SCTP port number for the local SVI process.
2.13.3.3.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.13.3.3.3 Values
Value Description
2905 Standard SCTP port
Other values
2.13.3.4 Local Address
2.13.3.4.1 Description IP address of the SVI-SG for the SCTP socket.
2.13.3.4.2 Definition
Applicable Modes User Type
All Read Write No-Default No-Secure
String
2.13.3.4.3 Values
Value Description
IP Address
2.13.3.5 Remote Port
2.13.3.5.1 Description SCTP port number for the remote host.
2.13.3.5.2 Definition
Applicable Modes User Type
All Read Write
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 63 of 124
2.13.3.5.3 Values
Value Description
2905 Standard SCTP port
Other values
2.13.3.6 Remote Address
2.13.3.6.1 Description IP Address for the remote host.
2.13.3.6.2 Definition
Applicable Modes User Type
All Read Write No-Default
String
2.13.3.6.3 Values
Value Description
IP Address
2.13.3.7 Outgoing Streams
2.13.3.7.1 Description Number of outgoing SCTP streams for this socket.
2.13.3.7.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.13.3.7.3 Values
Value Description
2
2.13.3.8 Incoming Streams
2.13.3.8.1 Description Number of incoming SCTP streams for this socket.
2.13.3.8.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.13.3.8.3 Values
Value Description
2
2.13.3.9 End
2.13.3.9.1 Description Controls the client-server behaviour of the SCTP socket.
2.13.3.9.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 64 of 124
All Read Write
Drop-down list
2.13.3.9.3 Values
Value Description
Server
Client
IPSP M3UA only
2.13.3.10 Protocol
2.13.3.10.1 Description Allows TCP-IP sockets to be used instead of SCTP.
2.13.3.10.2 Definition
Applicable Modes User Type
All Read Write
Drop Down list
2.13.3.10.3 Values
Value Description
TCP Uses a TCP/IP connection instead of SCTP
SCTP SCTP socket
2.13.3.11 IP
2.13.3.11.1 Description When using TCP/IP instead of SCTP (section 0), This is the IP socket resource to use.
2.13.3.11.2 Definition
Applicable Modes User Type
SCTP over TCP/IP only Read Write No-Default No-Secure
Resource
2.13.3.12 Redundancy Model
2.13.3.12.1 Description Controls the behaviour of the SCTP socket in a redundant system.
2.13.3.12.2 Definition
Applicable Modes User Type
All Read Write
Drop-Down list
2.13.3.12.3 Values
Value Description
Active The standby SCTP socket will be Activated
Inactive The standby SCTP will not be activated until Failover
Independent The SCTP will not depend on the plane in a redundant system
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 65 of 124
2.13.3.13 Multi-homed Local Address
2.13.3.13.1 Description Alternate local address for Multi-homed system.
2.13.3.13.2 Definition
Applicable Modes User Type
Multi-homed systems Read Write No-Default No-Secure
String
2.13.3.13.3 Values
Value Description
IP Address
2.13.3.14 Multi-homed Remote Address
2.13.3.14.1 Description Alternate Remote address for Multi-homed system.
2.13.3.14.2 Definition
Applicable Modes User Type
Multi-homed systems Read Write No-Default
String
2.13.3.14.3 Values
Value Description
IP Address
2.13.3.15 SCTP State
2.13.3.15.1 Description Internal SVI SCTP state.
2.13.3.15.2 Definition
Applicable Modes User Type
none Read Integer
2.13.3.16 SCTP Tmax
2.13.3.16.1 Description Retransmission Timeout Value in milliseconds.
2.13.3.16.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.13.3.16.3 Values
Value Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 66 of 124
2000 (default) 2 seconds
2.13.3.17 SCTP Heartbeat
2.13.3.17.1 Description Heartbeat interval timeout in milliseconds.
2.13.3.17.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.13.3.17.3 Values
Value Description
5000 (default) 5 seconds
2.13.3.18 SCTP Max Retry
2.13.3.18.1 Description Maximum number of retransmissions before ‘unreachable’.
2.13.3.18.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.13.3.18.3 Values
Value Description
2 (default)
2.13.3.19 Fd / Sktfd
2.13.3.19.1 Description The internal file handles of the SCTP socket.
2.13.3.19.2 Definition
Applicable Modes User Type
All Read No-Secure No-Init
Integer
2.13.3.19.3 Values
Value Description
System-set
2.13.3.20 No Delay
2.13.3.20.1 Description Allows the setting of the SCTP socket option ‘SCTP_NODELAY’.
2.13.3.20.2 Definition
Applicable Modes User Type
All Read Drop-down list
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 67 of 124
Write
2.13.3.20.3 Values
Value Description
On SCTP_NO_DELAY set
Off SCTP_NO_DELAY not set
2.13.3.21 Tx Msg Total
2.13.3.21.1 Description Statistic showing total number of Messages sent since system start.
2.13.3.21.2 Definition
Applicable Modes User Type
All Sctp Read Integer
2.13.3.22 Tx Msg/Sec
2.13.3.22.1 Description Statistic showing real-time Messages/Second being sent.
2.13.3.22.2 Definition
Applicable Modes User Type
All Sctp Read Integer
2.13.3.23 Tx Msg/Sec Max
2.13.3.23.1 Description Statistic showing maximum Messages/Second send rate since system start.
2.13.3.23.2 Definition
Applicable Modes User Type
All SCTP Read Integer
2.13.3.24 Rx Msg Total
2.13.3.24.1 Description Statistic showing total number of Messages received since system start.
2.13.3.24.2 Definition
Applicable Modes User Type
All SCTP Read Integer
2.13.3.25 Rx Msg/Sec
2.13.3.25.1 Description Statistic showing real-time Messages/Second being received.
2.13.3.25.2 Definition
Applicable Modes User Type
All Sctp Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 68 of 124
2.13.3.26 Rx Msg/Sec Max
2.13.3.26.1 Description Statistic showing maximum Messages/Second receive rate since system start.
2.13.3.26.2 Definition
Applicable Modes User Type
All Sctp Read Integer
2.13.3.27 Tx Bytes Total
2.13.3.27.1 Description Statistic showing total number of Bytes sent since system start.
2.13.3.27.2 Definition
Applicable Modes User Type
All Sctp Read Integer
2.13.3.28 Tx Bytes/Sec
2.13.3.28.1 Description Statistic showing real-time Bytes/Second being sent
2.13.3.28.2 Definition
Applicable Modes User Type
All Sctp Read Integer
2.13.3.29 Tx Bytes/Sec Max
2.13.3.29.1 Description Statistic showing maximum Bytes/Second send rate since system start
2.13.3.29.2 Definition
Applicable Modes User Type
All SCTP Read Integer
2.13.3.30 Rx Bytes Total
2.13.3.30.1 Description Statistic showing total number of Bytes received since system start
2.13.3.30.2 Definition
Applicable Modes User Type
All SCTP Read Integer
2.13.3.31 Rx Bytes/Sec
2.13.3.31.1 Description Statistic showing real-time Bytes/Second being received
2.13.3.31.2 Definition
Applicable Modes User Type
All SCTP Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 69 of 124
2.13.3.32 Rx Bytes/Sec Max
2.13.3.32.1 Description Statistic showing maximum Bytes/Second receive rate since system start
2.13.3.32.2 Definition
Applicable Modes User Type
All Sctp Read Integer
2.13.3.33 Rx Bytes/Sec Throttle
2.13.3.33.1 Description If the number of bytes per second threshold is exceeded then the SCTP will be throttled until the
next second. The SCTP link will queue the received SCTP messages
2.13.3.33.2 Definition
Applicable Modes User Type
All SCTP Write Integer
2.13.3.34 Rx Msgs/Sec Throttle
2.13.3.34.1 Description If the number of messages per second threshold is exceeded then the SCTP will be throttled until
the next second. The SCTP link will queue the received SCTP messages
2.13.3.34.2 Definition
Applicable Modes User Type
All Sctp Write Integer
2.13.3.35 Rx Bytes/Sec Max Queue
2.13.3.35.1 Description Number of SCTP messages to be queued after throttle before discard
2.13.3.35.2 Definition
Applicable Modes User Type
All Sctp Write Integer
2.13.3.36 Options
2.13.3.36.1 Description SCTP options.
2.13.3.36.2 Definition
Applicable Modes User Type
All Read Write No-Default
List
2.13.3.36.3 Values
Value Description
SNMP-Trap
Listener
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 70 of 124
Validate-Addr
SO_REUSEADDR Socket option SO_REUSEADDR will be set on sockets opened for this resource
Abort-Connection-On-Close
When connection is closed SCTP ABORT will be sent rather than SHUTDOWN
Allow-Duplicate-Local-Addr-Port
Normally the SVI will check the local address-port is unique for all SCTP resources; this option skips the check for this resource
Monitor This SCTP resource is a monitor-only device
Pcap-No-SaveFile-Delay
Monitor only - Packets from a Test Pcap File are processed as quickly as possibly rather than being processed in 'real' time
Pcap-SaveFile-Preserve-Ass
Monitor only - When a Test Pcap File is loaded, any Association data will be preserved rather than deleted (default is deletion)
2.14 ASP
2.14.1 Description
Defines the ASP in a SIGTRAN configuration.
2.14.2 Products
SVI-MG | SVI-MGC | SVI-STP | SVI-SMSC | SVI-SG.
2.14.3 Attributes
2.14.3.1 Type
2.14.3.1.1 Description The behaviour type of the resource instance.
2.14.3.1.2 Definition
Applicable Modes User Type
All Read Write
Drop Down List
2.14.3.1.3 Values
Value Description
ASP ASP
SS7Cisco ASP For Cisco Session manager connection
2.14.3.2 SCTP
2.14.3.2.1 Description The SCTP resource used by this ASP.
2.14.3.2.2 Definition
Applicable Modes User Type
All Read Write
Resource
2.14.3.3 Identifier
2.14.3.3.1 Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 71 of 124
Identifier used in ASP UP/ NOTIFY messages.
2.14.3.3.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.14.3.3.3 Values
Value Description
32-bit
2.14.3.4 Protocol
2.14.3.4.1 Description The SIGTRAN protocol.
2.14.3.4.2 Definition
Applicable Modes User Type
ALL Read Write
Drop Down List
2.14.3.4.3 Values
Value Description
M3UA
M2UA
M2PA
IUA
SLT
2.14.3.5 End
2.14.3.5.1 Description The Protocol End.
2.14.3.5.2 Definition
Applicable Modes User Type
All Read Write
Drop Down List
2.14.3.5.3 Values
Value Description
Server
Client
IPSP
2.14.3.6 As
2.14.3.6.1 Description The AS associated with this ASP.
2.14.3.6.2 Definition
Applicable Modes User Type
All Read Resource
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 72 of 124
Write
2.14.3.7 Redundancy Model
2.14.3.7.1 Description Controls the behaviour of the ASP in a redundant system.
2.14.3.7.2 Definition
Applicable Modes User Type
All Read Write
Drop-Down list
2.14.3.7.3 Values
Value Description
Active The standby ASP will be Activated
Inactive The standby ASP will not be activated until Failover
Independent The ASP will not depend on the plane in a redundant system
2.14.3.8 Include Interface ID
2.14.3.8.1 Description (M2UA only) If set, includes the Interface ID. The value used will be the ‘Interface ID’ setting on the
associated Signalling Link resource.
2.14.3.8.2 Definition
Applicable Modes User Type
M2UA only Read Write No-Default
List
2.14.3.8.3 Values
Value Description
On Interface id included in ASPAC and ASPIA messages
Off Interface ID not included
2.14.3.9 Client ASP State
2.14.3.9.1 Description Internal Client state.
2.14.3.9.2 Definition
Applicable Modes User Type
All Read No-Secure
Integer
2.14.3.10 Server ASP State
2.14.3.10.1 Description Internal Server State.
2.14.3.10.2 Definition
Applicable Modes User Type
All Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 73 of 124
No-Secure
2.14.3.11 Tbeat
2.14.3.11.1 Description Heartbeat timer duration (milliseconds).
2.14.3.11.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.14.3.11.3 Values
Value Description
0 (default) No heartbeat
2.14.3.12 TACK
2.14.3.12.1 Description Internal – whether the T_ACK timer is running.
2.14.3.12.2 Definition
Applicable Modes User Type
All Read Write No-Default No-Secure
Integer
2.14.3.13 Options
2.14.3.13.1 Description ASP options.
2.14.3.13.2 Definition
Applicable Modes User Type
All Read Write No-Default
List
2.14.3.13.3 Values
Value Description
Register (Client) Triggers Routing Key registration
SNMP-Trap
UNI-IPSP (Server) Causes ASP to act as a Unidirectional IPSP
2.14.3.14 Tx Msg/Sec
2.14.3.14.1 Description Statistic showing real-time Messages/Second being sent.
2.14.3.14.2 Definition
Applicable Modes User Type
All ASP Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 74 of 124
2.14.3.15 Tx Msg/Sec Max
2.14.3.15.1 Description Statistic showing maximum Messages/Second send rate since system start.
2.14.3.15.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.16 Rx Msg Total
2.14.3.16.1 Description Statistic showing total number of Messages received since system start.
2.14.3.16.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.17 Rx Msg/Sec
2.14.3.17.1 Description Statistic showing real-time Messages/Second being received.
2.14.3.17.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.18 Rx Msg/Sec Max
2.14.3.18.1 Description Statistic showing maximum Messages/Second receive rate since system start.
2.14.3.18.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.19 Tx Bytes Total
2.14.3.19.1 Description Statistic showing total number of Bytes sent since system start.
2.14.3.19.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.20 Tx Bytes/Sec
2.14.3.20.1 Description Statistic showing real-time Bytes/Second being sent
2.14.3.20.2 Definition
Applicable Modes User Type
All ASP Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 75 of 124
2.14.3.21 Tx Bytes/Sec Max
2.14.3.21.1 Description Statistic showing maximum Bytes/Second send rate since system start
2.14.3.21.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.22 Rx Bytes Total
2.14.3.22.1 Description Statistic showing total number of Bytes received since system start
2.14.3.22.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.23 Rx Bytes/Sec
2.14.3.23.1 Description Statistic showing real-time Bytes/Second being received
2.14.3.23.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.24 Rx Bytes/Sec Max
2.14.3.24.1 Description Statistic showing maximum Bytes/Second receive rate since system start
2.14.3.24.2 Definition
Applicable Modes User Type
All ASP Read Integer
2.14.3.25 Rx Bytes/Sec Throttle
2.14.3.25.1 Description If the number of bytes per second threshold is exceeded then the ASP will be throttled until the
next second. The ASP link will queue the received SCTP messages
2.14.3.25.2 Definition
Applicable Modes User Type
All ASP Write Integer
2.14.3.26 Rx Msgs/Sec Throttle
2.14.3.26.1 Description If the number of messages per second threshold is exceeded then the ASP will be throttled until the
next second. The ASP link will queue the received ASP messages
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 76 of 124
2.14.3.26.2 Definition
Applicable Modes User Type
All ASP Write Integer
2.14.3.27 Rx Bytes/Sec Max Queue
2.14.3.27.1 Description Number of ASP messages to be queued after throttle before discard
2.14.3.27.2 Definition
Applicable Modes User Type
All ASP Write Integer
2.14.3.28 displayRegistrations
2.14.3.28.1 Description Displays the M3UA dynamic routing key registrations against the ASP resource.
2.15 AS
2.15.1 Description
Defines the AS in a SIGTRAN configuration.
2.15.2 Products
SVI-MG | SVI-MGC | SVI-STP | SVI-SMSC | SVI-SG.
2.15.3 Attributes
2.15.3.1 Type
2.15.3.1.1 Description The behaviour type of the resource instance.
2.15.3.1.2 Definition
Applicable Modes User Type
All Read Write
List
2.15.3.1.3 Values
Value Description
M3UA AS
IUA AS
2.15.3.2 Originating Point
Deprecated, End-Of-Life.
2.15.3.3 Destination Point
Deprecated, End-Of-Life.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 77 of 124
2.15.3.4 IP Resource
Deprecated, End-Of-Life.
2.15.3.5 ASP
Deprecated, End-Of-Life.
2.15.3.6 Traffic Mode
2.15.3.6.1 Description The AS Traffic Mode.
2.15.3.6.2 Definition
Applicable Modes User Type
All Read Write
List
2.15.3.6.3 Values
Value Description
Override Last ASP active is used for all traffic
Loadshare Traffic spread equally over all ASPs
Broadcast All traffic sent using all ASPs
SCCP Routing
2.15.3.7 SCCP DB
2.15.3.7.1 Description SUA –the SCCP Db Resource to be used for routing.
2.15.3.7.2 Definition
Applicable Modes User Type
SUA only Read Write No-Default
Resource
2.15.3.8 IC L3Label
2.15.3.8.1 Description
Range of L3 Label resources to examine when routing M3UA messages from this AS.
2.15.3.8.2 Definition
Applicable Modes User Type
M3UA only Read / Write String
2.15.3.8.3 Values
Value Description
Range of Resource instances
2.15.3.9 OG L3Label
2.15.3.9.1 Description
Range of L3 Label resources to examine when routing M3UA messages to this AS.
2.15.3.9.2 Definition
Applicable Modes User Type
M3UA only Read / Write String
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 78 of 124
2.15.3.9.3 Values
Value Description
Range of Resource instances
2.15.3.10 AS State
2.15.3.10.1 Description
The internal state of the AS.
2.15.3.10.2 Definition
Applicable Modes User Type
All Read List
2.15.3.10.3 Values
Value Description
AS-Inactive
AS-Pending
AS-Active
2.15.3.11 Routing Context Present
2.15.3.11.1 Description
Controls SVI M3UA client’s inclusion of ‘Routing Context’ in ASPAC message.
2.15.3.11.2 Definition
Applicable Modes User Type
M3UA client Read/Write List
2.15.3.11.3 Values
Value Description
Present ASPAC will include RC set to the value in section 2.15.3.12
Absent ASPAC will not include RC
2.15.3.12 Routing Context
2.15.3.12.1 Description The Routing Context value used in M3UA ASPAC messages.
2.15.3.12.2 Definition
Applicable Modes User Type
M3UA client Read Write
Integer
2.15.3.12.3 Values
Value Description
0x0 - 0xFFFFFFFD Valid Routing Context values.
0xFFFFFFFE/0xFFFFFFFF Reserved for internal use
2.15.3.13 Options
2.15.3.13.1 Description The different optional configuration allowed in AS resource.
2.15.3.13.2 Definition
Applicable Modes User Type
M3UA client Read Write
Bitmask
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 79 of 124
2.15.3.13.3 Values
Value Description
None No additional options configured.
Single-DAUD This will make SVI send M3UA DAUD messages with only 1 affected destination pointcode inside it.
STP-Routing Forces the SVI to process M3UA messages instead of attempting routing at MTP-L3-Routing. This means that the Labels will be checked even if the SVI-SS connection is a client
SG-Routing Forces the SVI to process M3UA messages as an SG, even if as a client.
AS-Loadshare Traffic will be load-shared across this AS and its partner (subject to AS status and DP status)
AS-Primary Traffic will be sent on this AS in preference to its partner (subject to AS status and DP status)
AS-Secondary Traffic will be sent on this AS's partner in preference to this AS (subject to AS status and DP status)
Forward-DPC-Status Will forward the DPC status of a connection if the connection type is Client
SNMP-Trap Add snmp trap generation on resource state change.
2.15.3.14 Tx Msg/Sec
2.15.3.14.1 Description Statistic showing real-time Messages/Second being sent.
2.15.3.14.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.15 Tx Msg/Sec Max
2.15.3.15.1 Description Statistic showing maximum Messages/Second send rate since system start.
2.15.3.15.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.16 Rx Msg Total
2.15.3.16.1 Description Statistic showing total number of Messages received since system start.
2.15.3.16.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.17 Rx Msg/Sec
2.15.3.17.1 Description Statistic showing real-time Messages/Second being received.
2.15.3.17.2 Definition
Applicable Modes User Type
All AS Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 80 of 124
2.15.3.18 Rx Msg/Sec Max
2.15.3.18.1 Description Statistic showing maximum Messages/Second receive rate since system start.
2.15.3.18.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.19 Tx Bytes Total
2.15.3.19.1 Description Statistic showing total number of Bytes sent since system start.
2.15.3.19.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.20 Tx Bytes/Sec
2.15.3.20.1 Description Statistic showing real-time Bytes/Second being sent
2.15.3.20.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.21 Tx Bytes/Sec Max
2.15.3.21.1 Description Statistic showing maximum Bytes/Second send rate since system start
2.15.3.21.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.22 Rx Bytes Total
2.15.3.22.1 Description Statistic showing total number of Bytes received since system start
2.15.3.22.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.23 Rx Bytes/Sec
2.15.3.23.1 Description Statistic showing real-time Bytes/Second being received
2.15.3.23.2 Definition
Applicable Modes User Type
All AS Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 81 of 124
2.15.3.24 Rx Bytes/Sec Max
2.15.3.24.1 Description Statistic showing maximum Bytes/Second receive rate since system start
2.15.3.24.2 Definition
Applicable Modes User Type
All AS Read Integer
2.15.3.25 Rx Bytes/Sec Throttle
2.15.3.25.1 Description If the number of bytes per second threshold is exceeded then the AS will be throttled until the next
second. The AS link will queue the received AS messages
2.15.3.25.2 Definition
Applicable Modes User Type
All AS Write Integer
2.15.3.26 Rx Msgs/Sec Throttle
2.15.3.26.1 Description If the number of messages per second threshold is exceeded then the AS will be throttled until the
next second. The AS link will queue the received AS messages
2.15.3.26.2 Definition
Applicable Modes User Type
All AS Write Integer
2.15.3.27 Rx Bytes/Sec Max Queue
2.15.3.27.1 Description Number of AS messages to be queued after throttle before discard
2.15.3.27.2 Definition
Applicable Modes User Type
All AS Write Integer
2.15.3.28 SSME XML
2.15.3.28.1 Description XML Resource to be used for STP routing.
2.15.3.28.2 Definition
Applicable Modes User Type
All AS Read Write No-Default
Resource
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 82 of 124
2.16 L3 Label / SCCP Label / TCAP Label
The L3, SCCP and TCAP resources have a similar structure.
‘Match’ Section – multiple parameters to form a match.
<param> Present
(Where <param> is the name of a protocol parameter, which may be present in a message)
Used to match against the presence (or absence) of a parameter in the received message
‘Present’ – must be Present to match
‘Absent’ – must be Absent to match
‘Ignore’ – presence or absence does not affect the match
<param>
(Where <param> is the name of a protocol parameter)
Use to match against the value of a parameter in the received message
<value> - received parameter must be this value
‘Ignore’ – value will not affect the match
‘Set_’ Section – multiple parameters to manipulate the message
‘Set <param> Present’ Attributes
(Where <param> is the name of a protocol parameter, which may be present in a message)
Used in the manipulation of messages.
‘Present’ – parameter will be included in outgoing message
‘Absent’ – parameter will not be included in the outgoing message
‘Leave’ – parameter will not be altered
‘Set <param>’
(Where <param> is the name of a protocol parameter)
<value> - if the parameter is either (a) already in the received message or (b) ‘Set <param>
Present’ is ‘Present’, the outgoing message will have this parameter, set to this value.
‘leave’ – if present, value will not be altered
Other Labels Section
‘More <X> Labels’ ... attribute
If set, when the routing process matches this label, the labels listed in this are also
searched for a match.
‘<X> Labels’ attribute
e.g. SCCP label, TCAP label – the next layer up of parameter matching
Routing
‘MTP Route’ attribute
2.16.1 L3 Label
2.16.1.1 Description
Resource used to define the Layer 3 label for best match routing/manipulation.
2.16.1.2 Products
SVI-STP
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 83 of 124
2.16.1.3 Attributes
2.16.1.3.1 Options
2.16.1.3.1.1 Definition
Applicable Modes User Type
All Read Write No-Default
Bit Mask Flag
2.16.1.3.1.2 Values
Value Description
SNMP-Trap If the resource changes state, an SNMP trap will be sent to the address configured on the debug resource.
2.16.1.3.2 OPC
2.16.1.3.2.1 Description
Match either a defined value or any OPC which is present.
2.16.1.3.2.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.2.3 Values
Value Description
Match to defined
Ignore Match any OPC present
2.16.1.3.3 DPC
2.16.1.3.3.1 Description
Match either a defined value or any DPC which is present.
2.16.1.3.3.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.3.3 Values
Value Description
Match to defined
Ignore Match any DPC present
2.16.1.3.4 SI
2.16.1.3.4.1 Description
Match either a defined value or any SI which is present.
2.16.1.3.4.2 Definition
Applicable Modes User Type
All Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 84 of 124
2.16.1.3.4.3 Values
Value Description
Match to defined
Ignore Match any SI present
2.16.1.3.5 NI
2.16.1.3.5.1 Description
Match either a defined value or any NI which is present.
2.16.1.3.5.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.5.3 Values
Value Description
Match to defined
Ignore Match any NI present
2.16.1.3.6 M3UA_NA_Present
2.16.1.3.6.1 Description
(M3UA messages only) Match only if the Network Appearance parameter is present in the message
2.16.1.3.6.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop Down List
2.16.1.3.6.3 Values
Value Description
Present Network Appearance must be Present
Absent Network Appearance must be Absent
Ignore Network Appearance can be present or absent, but will not count towards a best match total.
2.16.1.3.7 M3UA_NA
2.16.1.3.7.1 Description
(M3UA messages only) Match either a defined value or any Network Appearance which is present.
2.16.1.3.7.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.7.3 Values
Value Description
Match to defined
Ignore Match any NA present
2.16.1.3.8 M3UA_RC_Present
2.16.1.3.8.1 Description
(M3UA messages only) Match only if the Routing Context parameter is present in the message
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 85 of 124
2.16.1.3.8.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop Down List
2.16.1.3.8.3 Values
Value Description
Present Routing Context must be Present
Absent Routing Context must be Absent
Ignore Routing Context can be present or absent, but will not count towards a best match total.
2.16.1.3.9 M3UA_RC
2.16.1.3.9.1 Description
(M3UA messages only) Match either a defined value or any Routing Context which is present.
2.16.1.3.9.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.9.3 Values
Value Description
Match to defined
Ignore Match any RC present
2.16.1.3.10 M3UA_CI_Present
2.16.1.3.10.1 Description
(M3UA messages only) Match only if the Correlation Id parameter is present in the message
2.16.1.3.10.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop Down List
2.16.1.3.10.3 Values
Value Description
Present Correlation Id must be Present
Absent Correlation Id must be Absent
Ignore Correlation Id can be present or absent, but will not count towards a best match total.
2.16.1.3.11 M3UA_CI
2.16.1.3.11.1 Description
(M3UA messages only) Match either a defined value or any Correlation ID which is present.
2.16.1.3.11.2 Definition
Applicable Modes User Type
All Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 86 of 124
2.16.1.3.11.3 Values
Value Description
Match to defined
Ignore Match any CI present
2.16.1.3.12 Set OPC
2.16.1.3.12.1 Description
Manipulate the OPC to the defined value or leave it in the current state.
2.16.1.3.12.2 Definition
Applicable Modes User Type
All Write Integer
2.16.1.3.12.3 Values
Value Description
Manipulate OPC to value set
Ignore Do not manipulate
2.16.1.3.13 Set DPC
2.16.1.3.13.1 Description
Manipulate the DPC to the defined value or leave it in the current state.
2.16.1.3.13.2 Definition
Applicable Modes User Type
All Write Integer
2.16.1.3.13.3 Values
Value Description
Manipulate DPC to value set
Ignore Do not manipulate
2.16.1.3.14 Set SI
2.16.1.3.14.1 Description
Manipulate the SI to the defined value or leave it in the current state.
2.16.1.3.14.2 Definition
Applicable Modes User Type
All Write Integer
2.16.1.3.14.3 Values
Value Description
Manipulate SI to value set
Ignore Do not manipulate
2.16.1.3.15 Set NI
2.16.1.3.15.1 Description
Manipulate the NI to the defined value or leave it in the current state.
2.16.1.3.15.2 Definition
Applicable Modes User Type
All Write Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 87 of 124
2.16.1.3.15.3 Values
Value Description
Manipulate SI to value set
Ignore Do not manipulate
2.16.1.3.16 Set_M3UA_NA_Present
2.16.1.3.16.1 Description
(M3UA messages only) Controls the presence of the Network Appearance parameter in the outgoing
message
2.16.1.3.16.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop Down List
2.16.1.3.16.3 Values
Value Description
Present Network Appearance will be Present in the outgoing message
Absent Network Appearance will not be in the outgoing message
Ignore The presence of Network Appearance in the outgoing message, will be the same as in the incoming message
2.16.1.3.17 Set_M3UA_NA
2.16.1.3.17.1 Description
(M3UA messages only)
If Network Appearance is to be included in the outgoing message (set by M3UA_NA_Present), this
attribute sets the value.
2.16.1.3.17.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.17.3 Values
Value Description
0-HFFFFFFFD Insert set value into the message
Leave Do not change value
2.16.1.3.18 Set_M3UA_RC_Present
2.16.1.3.18.1 Description
(M3UA messages only) Controls the presence of the Routing Context parameter in the outgoing
message.
2.16.1.3.18.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop Down List
2.16.1.3.18.3 Values
Value Description
Present Routing Context will be Present in the outgoing message
Absent Routing Context will not be in the outgoing message
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 88 of 124
Ignore The presence of Routing Context in the outgoing message, will be the same as in the incoming message
2.16.1.3.19 Set_M3UA_RC
2.16.1.3.19.1 Description
(M3UA messages only)
If Routing Context is to be included in the outgoing message (set by M3UA_RC_Present), this
attribute sets the value.
2.16.1.3.19.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.19.3 Values
Value Description
0-HFFFFFFFD Insert set value into the message
Leave Do not change value
2.16.1.3.20 Set_M3UA_CI_Present
2.16.1.3.20.1 Description
(M3UA messages only) Controls the presence of the Correlation ID parameter in the outgoing
message
2.16.1.3.20.2 Definition
Applicable Modes User Type
All Read Write No-Default
Drop Down List
2.16.1.3.20.3 Values
Value Description
Present Correlation ID will be Present in the outgoing message
Absent Correlation ID will not be in the outgoing message
Ignore The presence of Correlation ID in the outgoing message, will be the same as in the incoming message
2.16.1.3.21 Set_M3UA_CI
2.16.1.3.21.1 Description
(M3UA messages only)
If Correlation ID is to be included in the outgoing message (set by M3UA_CI_Present), this attribute
sets the value.
2.16.1.3.21.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.21.3 Values
Value Description
0-HFFFFFFFD Insert set value into the message
Leave Do not change value
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 89 of 124
2.16.1.3.22 More L3Labels
2.16.1.3.22.1 Description
Add additional Layer 3 labels for best match routing/manipulation.
2.16.1.3.22.2 Definition
Applicable Modes User Type
All Read Resource Identifier
2.16.1.3.23 SCCPLabels
2.16.1.3.23.1 Description
Add SCCP labels for best match routing/manipulation.
2.16.1.3.23.2 Definition
Applicable Modes User Type
All Read Resource Identifier
2.16.1.3.24 MTP Route
2.16.1.3.24.1 Description
Adds an MTP Route.
2.16.1.3.24.2 Definition
Applicable Modes User Type
All Read Resource Identifier
2.16.1.3.25 Tx Msg Total
2.16.1.3.25.1 Description
Statistic showing total number of Messages being sent matching this label.
2.16.1.3.25.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.26 Tx Msg/Sec
2.16.1.3.26.1 Description
Statistic showing real-time Messages/Second being sent matching this label.
2.16.1.3.26.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.27 Tx Msg/Sec Max
2.16.1.3.27.1 Description
Statistic showing maximum Messages/Second send rate since system start matching this label.
2.16.1.3.27.2 Definition
Applicable Modes User Type
All Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 90 of 124
2.16.1.3.28 Rx Msg Total
2.16.1.3.28.1 Description
Statistic showing total number of Messages received since system start.
2.16.1.3.28.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.29 Rx Msg/Sec
2.16.1.3.29.1 Description
Statistic showing real-time Messages/Second being received matching this label.
2.16.1.3.29.2 Definition
Applicable Modes User Type
All Read Integer
2.16.1.3.30 Rx Msg/Sec Max
2.16.1.3.30.1 Description
Statistic showing maximum Messages/Second receive rate since system start matching this label.
2.16.1.3.30.2 Definition
Applicable Modes User Type
All Read Integer
2.16.2 SCCP Label
2.16.2.1 Description
Resource used to define the SCCP label for best match routing/manipulation.
2.16.2.2 Products
SVI-STP
2.16.2.3 Attributes
2.16.2.3.1 Options
2.16.2.3.1.1 Definition
Applicable Modes User Type
All Read Write No-Default
Bit Mask Flag
2.16.2.3.1.2 Values
Value Description
SNMP-Trap If the resource changes state, an SNMP trap will be sent to the address configured on the debug resource.
2.16.2.3.2 CDPN_Present
2.16.2.3.2.1 Description
Define whether the CDPN is expected to be present, not present or choose to ignore the state.
2.16.2.3.2.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 91 of 124
All Read Write No-Default
Integer
2.16.2.3.2.3 Values
Value Description
Present CDPN must be present
Absent CDPN must be absent
Ignore CDPN can be present or absent, but will not count towards a best match total.
2.16.2.3.3 CDPN_National
2.16.2.3.3.1 Description
Define the value expected or ignore the value.
2.16.2.3.3.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.3.3 Values
Value Description
Ignore CDPN can be national or international, but will not count towards a best match total.
National CDPN is national
International CDPN is international
2.16.2.3.4 CDPN_RoutingInd
2.16.2.3.4.1 Description
Define the value expected or ignore the value.
2.16.2.3.4.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.4.3 Values
Value Description
Route On GT CDPN should Route using the Global Title
Route On SSN CDPN should Route using the Sub System Number
Ignore CDPN can route using the Global Title or Sub System Number, but will not count towards a best match total.
2.16.2.3.5 CDPN_SSN_Present
2.16.2.3.5.1 Description
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 92 of 124
Define the value expected or ignore the value.
2.16.2.3.5.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.5.3 Values
Value Description
Present CDPN SSN must be present
Absent CDPN SSN must be absent
Ignore CDPN SSN can be present or absent, but will not count towards a best match total.
2.16.2.3.6 CDPN_SSN
2.16.2.3.6.1 Description
Define the SSN type.
2.16.2.3.6.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.6.3 Values
Value Description
ISUP Sets the type matched to ISUP
OMAP Sets the type matched to OMAP
MAP Sets the type matched to MAP
HLR Sets the type matched to HLR
VLR Sets the type matched to VLR
MSC Sets the type matched to MSC
EIC Sets the type matched to EIC
AUC Sets the type matched to AUC
ISDN SS Sets the type matched to ISDN SS
B-ISDN Sets the type matched to B-ISDN
TCtest Sets the type matched to TCtest
Ignore/Leave CDPN SSN can be any type, but will not count towards a best match total.
2.16.2.3.7 CDPN_Pointcode_Present
2.16.2.3.7.1 Description
Define the value expected or ignore the value.
2.16.2.3.7.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.7.3 Values
Value Description
Present CDPN Pointcode must be present
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 93 of 124
Absent CDPN Pointcode must be absent
Ignore CDPN Pointcode can be present or absent, but will not count towards a best match total.
2.16.2.3.8 CDPN_Pointcode
2.16.2.3.8.1 Description
Define the value expected or ignore the value.
2.16.2.3.8.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.8.3 Values
Value Description
Define value to match
Ignore Any CDPN Pointcode will be matched, but will not count towards a best match total.
2.16.2.3.9 CDPN_GT_Present
2.16.2.3.9.1 Description
Define the value expected or ignore the value.
2.16.2.3.9.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.9.3 Values
Value Description
Present CDPN GT must be present
Absent CDPN GT must be absent
Ignore CDPN GT can be present or absent, but will not count towards a best match total.
2.16.2.3.10 CDPN_NumberingPlan_Present
2.16.2.3.10.1 Description
Define the value expected or ignore the value.
2.16.2.3.10.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.10.3 Values
Value Description
Present CDPN Numbering Plan must be present
Absent CDPN Numbering Plan must be absent
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 94 of 124
Ignore CDPN Numbering Plan can be present or absent, but will not count towards a best match total.
2.16.2.3.11 CDPN_NumberingPlan
2.16.2.3.11.1 Description
Define the Numbering Plan type.
2.16.2.3.11.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.11.3 Values
Value Description
Unknown Sets the type matched to Unknown
ISDN Sets the type matched to ISDN
Generic Sets the type matched to Generic
Data Sets the type matched to Data
Telex Sets the type matched to Telex
Maritime Mobile Sets the type matched to Maritime Mobile
Land Mobile Sets the type matched to Land Mobile
ISDN/mobile Sets the type matched to ISDN/mobile
Ignore/Leave CDPN Numbering Plan can be any type, but will not count towards a best match total.
2.16.2.3.12 CDPN_TranslationType_Present
2.16.2.3.12.1 Description
Define the value expected or ignore the value.
2.16.2.3.12.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.12.3 Values
Value Description
Present CDPN Translation Type must be present
Absent CDPN Translation Type must be absent
Ignore CDPN Translation Type can be present or absent, but will not count towards a best match total.
2.16.2.3.13 CDPN_ TranslationType
2.16.2.3.13.1 Description
Define the value expected or ignore the value.
2.16.2.3.13.2 Definition
Applicable Modes User Type
All Read Write
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 95 of 124
No-Default
2.16.2.3.13.3 Values
Value Description
Define value to match
Ignore Any CDPN Translation Type will be matched, but will not count towards a best match total.
2.16.2.3.14 CDPN_ EncodingScheme_Present
2.16.2.3.14.1 Description
Define the value expected or ignore the value.
2.16.2.3.14.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.14.3 Values
Value Description
Present CDPN Encoding Scheme must be present
Absent CDPN Encoding Scheme must be absent
Ignore CDPN Encoding Scheme can be present or absent, but will not count towards a best match total.
2.16.2.3.15 CDPN_ EncodingScheme
2.16.2.3.15.1 Description
Define the Encoding Scheme type.
2.16.2.3.15.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.15.3 Values
Value Description
Unknown Sets the type matched to Unknown
BCD Sets the type matched to BCD
National Sets the type matched to National
Ignore/Leave CDPN Encoding Scheme can be any type, but will not count towards a best match total.
2.16.2.3.16 CDPN_ NOA_Present
2.16.2.3.16.1 Description
Define the value expected or ignore the value.
2.16.2.3.16.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 96 of 124
All Read Write No-Default
Integer
2.16.2.3.16.3 Values
Value Description
Present CDPN NOA must be present
Absent CDPN NOA must be absent
Ignore CDPN NOA can be present or absent, but will not count towards a best match total.
2.16.2.3.17 CDPN_ NOA
2.16.2.3.17.1 Description
Define the NOA type.
2.16.2.3.17.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.17.3 Values
Value Description
Spare Sets the type matched to Spare
Subscriber Sets the type matched to Subscriber
Unknown Sets the type matched to Unknown
National Sets the type matched to National
International Sets the type matched to International
Network Specific Sets the type matched to Network Specific
UK Specific Sets the type matched to UK Specific
Ignore/Leave CDPN Encoding Scheme can be any type, but will not count towards a best match total.
2.16.2.3.18 CGPN_Present
2.16.2.3.18.1 Description
Define whether the CGPN is expected to be present, not present or choose to ignore the state.
2.16.2.3.18.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.18.3 Values
Value Description
Present CGPN must be present
Absent CGPN must be absent
Ignore CGPN can be present or absent, but will not count towards a best match total.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 97 of 124
2.16.2.3.19 CGPN _National
2.16.2.3.19.1 Description
Define the value expected or ignore the value.
2.16.2.3.19.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.19.3 Values
Value Description
Ignore CGPN can be national or international, but will not count towards a best match total.
National CGPN is national
International CGPN is international
2.16.2.3.20 CGPN_RoutingInd
2.16.2.3.20.1 Description
Define the value expected or ignore the value.
2.16.2.3.20.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.20.3 Values
Value Description
Route On GT CGPN should Route using the Global Title
Route On SSN CGPN should Route using the Sub System Number
Ignore CGPN can route using the Global Title or Sub System Number, but will not count towards a best match total.
2.16.2.3.21 CGPN_SSN_Present
2.16.2.3.21.1 Description
Define the value expected or ignore the value.
2.16.2.3.21.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.21.3 Values
Value Description
Present CGPN SSN must be present
Absent CGPN SSN must be absent
Ignore CGPN SSN can be present or absent, but will not count towards a best match total.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 98 of 124
2.16.2.3.22 CGPN_SSN
2.16.2.3.22.1 Description
Define the SSN type.
2.16.2.3.22.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.22.3 Values
Value Description
ISUP Sets the type matched to ISUP
OMAP Sets the type matched to OMAP
MAP Sets the type matched to MAP
HLR Sets the type matched to HLR
VLR Sets the type matched to VLR
MSC Sets the type matched to MSC
EIC Sets the type matched to EIC
AUC Sets the type matched to AUC
ISDN SS Sets the type matched to ISDN SS
B-ISDN Sets the type matched to B-ISDN
TCtest Sets the type matched to TCtest
Ignore/Leave CGPN SSN can be any type, but will not count towards a best match total.
2.16.2.3.23 CGPN_Pointcode_Present
2.16.2.3.23.1 Description
Define the value expected or ignore the value.
2.16.2.3.23.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.23.3 Values
Value Description
Present CGPN Pointcode must be present
Absent CGPN Pointcode must be absent
Ignore CGPN Pointcode can be present or absent, but will not count towards a best match total.
2.16.2.3.24 CGPN_Pointcode
2.16.2.3.24.1 Description
Define the value expected or ignore the value.
2.16.2.3.24.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 99 of 124
All Read Write No-Default
Integer
2.16.2.3.24.3 Values
Value Description
Define value to match
Ignore Any CGPN Pointcode will be matched, but will not count towards a best match total.
2.16.2.3.25 CGPN_GT_Present
2.16.2.3.25.1 Description
Define the value expected or ignore the value.
2.16.2.3.25.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.25.3 Values
Value Description
Present CGPN GT must be present
Absent CGPN GT must be absent
Ignore CGPN GT can be present or absent, but will not count towards a best match total.
2.16.2.3.26 CGPN_NumberingPlan_Present
2.16.2.3.26.1 Description
Define the value expected or ignore the value.
2.16.2.3.26.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.26.3 Values
Value Description
Present CGPN Numbering Plan must be present
Absent CGPN Numbering Plan must be absent
Ignore CGPN Numbering Plan can be present or absent, but will not count towards a best match total.
2.16.2.3.27 CGPN_NumberingPlan
2.16.2.3.27.1 Description
Define the Numbering Plan type.
2.16.2.3.27.2 Definition
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 100 of 124
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.27.3 Values
Value Description
Unknown Sets the type matched to Unknown
ISDN Sets the type matched to ISDN
Generic Sets the type matched to Generic
Data Sets the type matched to Data
Telex Sets the type matched to Telex
Maritime Mobile Sets the type matched to Maritime Mobile
Land Mobile Sets the type matched to Land Mobile
ISDN/mobile Sets the type matched to ISDN/mobile
Ignore/Leave CGPN Numbering Plan can be any type, but will not count towards a best match total.
2.16.2.3.28 CGPN_TranslationType_Present
2.16.2.3.28.1 Description
Define the value expected or ignore the value.
2.16.2.3.28.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.28.3 Values
Value Description
Present CGPN Translation Type must be present
Absent CGPN Translation Type must be absent
Ignore CGPN Translation Type can be present or absent, but will not count towards a best match total.
2.16.2.3.29 CGPN_ TranslationType
2.16.2.3.29.1 Description
Define the value expected or ignore the value.
2.16.2.3.29.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.29.3 Values
Value Description
Define value to match
Ignore Any CGPN Translation Type will be matched, but will not count towards a best match total.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 101 of 124
2.16.2.3.30 CGPN_ EncodingScheme_Present
2.16.2.3.30.1 Description
Define the value expected or ignore the value.
2.16.2.3.30.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.30.3 Values
Value Description
Present CGPN Encoding Scheme must be present
Absent CGPN Encoding Scheme must be absent
Ignore CGPN Encoding Scheme can be present or absent, but will not count towards a best match total.
2.16.2.3.31 CGPN_ EncodingScheme
2.16.2.3.31.1 Description
Define the Encoding Scheme type.
2.16.2.3.31.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.31.3 Values
Value Description
Unknown Sets the type matched to Unknown
BCD Sets the type matched to BCD
National Sets the type matched to National
Ignore/Leave CGPN Encoding Scheme can be any type, but will not count towards a best match total.
2.16.2.3.32 CGPN_ NOA_Present
2.16.2.3.32.1 Description
Define the value expected or ignore the value.
2.16.2.3.32.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.32.3 Values
Value Description
Present CGPN NOA must be present
Absent CGPN NOA must be absent
Ignore CGPN NOA can be present or absent, but will not count towards a best match total.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 102 of 124
2.16.2.3.33 CGPN_ NOA
2.16.2.3.33.1 Description
Define the NOA type.
2.16.2.3.33.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.33.3 Values
Value Description
Spare Sets the type matched to Spare
Subscriber Sets the type matched to Subscriber
Unknown Sets the type matched to Unknown
National Sets the type matched to National
International Sets the type matched to International
Network Specific Sets the type matched to Network Specific
UK Specific Sets the type matched to UK Specific
Ignore/Leave CGPN Encoding Scheme can be any type, but will not count towards a best match total.
2.16.2.3.34 set Variant
2.16.2.3.34.1 Description
Select the variant to be used for decoding.
This attribute is not used for matching and will be applied regardless.
2.16.2.3.34.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.34.3 Values
Value Description
ITU Sets the Variant to ITU
ANSI Sets the Variant to ANSI
Use L3 Variant Use the variant of the L3 transport that the message will be sent to
2.16.2.3.35 set_cdpn_Present
2.16.2.3.35.1 Description
Set whether the CDPN is expected to be present, not present or choose not to manipulate the
current value.
2.16.2.3.35.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 103 of 124
2.16.2.3.35.3 Values
Value Description
Present Set CDPN present
Absent Set CDPN absent
Leave Do not manipulate value
2.16.2.3.36 set_cdpn_National
2.16.2.3.36.1 Description
Set whether the CDPN is expected to be present, not present or choose not to manipulate the
current value.
2.16.2.3.36.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.36.3 Values
Value Description
National Set CDPN to National
International Set CDPN to International
Ignore/Leave Do not manipulate value
2.16.2.3.37 set_cdpn_RoutingInd
2.16.2.3.37.1 Description
Set whether the CDPN Routing Ind is expected to Route on GT, Route on SSN or choose not to
manipulate the current value.
2.16.2.3.37.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.37.3 Values
Value Description
National Set CDPN to Route on GT
International Set CDPN to Route on SSN
Ignore/Leave Do not manipulate value
2.16.2.3.38 set_cdpn_SSN_Present
2.16.2.3.38.1 Description
Set whether the SSN is expected to be present, not present or choose not to manipulate the current
value.
2.16.2.3.38.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.38.3 Values
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 104 of 124
Value Description
Present Set SSN to present
Absent Set SSN to absent
Leave Do not manipulate value
2.16.2.3.39 set_cdpn_SSN
2.16.2.3.39.1 Description
Set the SSN is type or choose not to manipulate the current value.
2.16.2.3.39.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.39.3 Values
Value Description
ISUP Sets the type to ISUP
OMAP Sets the type to OMAP
MAP Sets the type to MAP
HLR Sets the type to HLR
VLR Sets the type to VLR
MSC Sets the type to MSC
EIC Sets the type to EIC
AUC Sets the type to AUC
ISDN SS Sets the type to ISDN SS
B-ISDN Sets the type to B-ISDN
TCtest Sets the type to TCtest
Ignore/Leave CDPN SSN can be any type, but will not count towards a best match total.
2.16.2.3.40 set_cdpn_Pointcode_Present
2.16.2.3.40.1 Description
Set whether the CDPN Pointcode is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.40.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.40.3 Values
Value Description
Present Set CDPN Pointcode must be present
Absent Set CDPN Pointcode must be absent
Leave Do not manipulate value
2.16.2.3.41 set_cdpn_Pointcode
Set the CDPN Pointcode or choose not to manipulate the current value.
2.16.2.3.41.1 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 105 of 124
All Read Write No-Default
Integer
2.16.2.3.41.2 Values
Value Description
Set CDPN Pointcode value
Leave Do not manipulate value
2.16.2.3.42 set_cdpn_GT_Present
2.16.2.3.42.1 Description
Set whether the CDPN Global Title is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.42.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.42.3 Values
Value Description
Present Set CDPN GT must be present
Absent Set CDPN GT must be absent
Leave Do not manipulate value
2.16.2.3.43 set_cdpn_NumberingPlan_Present
2.16.2.3.43.1 Description
Set whether the CDPN Numbering Plan is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.43.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.43.3 Values
Value Description
Present Set CDPN Numbering Plan must be present
Absent Set CDPN Numbering Plan must be absent
Leave Do not manipulate value
2.16.2.3.44 set_cdpn_NumberingPlan
2.16.2.3.44.1 Description
Set the Numbering Plan type or choose not to manipulate the current value.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 106 of 124
2.16.2.3.44.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.44.3 Values
Value Description
Unknown Sets the type to Unknown
ISDN Sets the type to ISDN
Generic Sets the type to Generic
Data Sets the type to Data
Telex Sets the type to Telex
Maritime Mobile Sets the type to Maritime Mobile
Land Mobile Sets the type to Land Mobile
ISDN/mobile Sets the type to ISDN/mobile
Ignore/Leave Do not manipulate value
2.16.2.3.45 set_cdpn_TranslationType_Present
2.16.2.3.45.1 Description
Set whether the CDPN Numbering Plan is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.45.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.45.3 Values
Value Description
Present Set CDPN Translation Type must be present
Absent Set CDPN Translation Type must be absent
Leave Do not manipulate value
2.16.2.3.46 Set_cdpn_TranslationType
2.16.2.3.46.1 Description
Define the value expected or choose not to manipulate the current value.
2.16.2.3.46.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.46.3 Values
Value Description
set Translation Type value
Leave Do not manipulate value
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 107 of 124
2.16.2.3.47 set_cdpn_EncodingScheme_Present
2.16.2.3.47.1 Description
Set whether the CDPN Numbering Plan is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.47.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.47.3 Values
Value Description
Present Set CDPN Encoding Scheme must be present
Absent Set CDPN Encoding Scheme must be absent
Leave Do not manipulate value
2.16.2.3.48 set_cdpn_ EncodingScheme
2.16.2.3.48.1 Description
Set the Encoding Scheme type or choose not to manipulate the current value.
2.16.2.3.48.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.48.3 Values
Value Description
Unknown Sets the type to Unknown
BCD Sets the type to BCD
National Sets the type to National
Ignore/Leave Do not manipulate value
2.16.2.3.49 set_cdpn_NOA_Present
2.16.2.3.49.1 Description
Set whether the CDPN NOA is expected to be present, not present or choose not to manipulate the
current value.
2.16.2.3.49.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.49.3 Values
Value Description
Present Set CDPN NOA must be present
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 108 of 124
Absent Set CDPN NOA must be absent
Leave Do not manipulate value
2.16.2.3.50 set_cdpn_ NOA
2.16.2.3.50.1 Description
Set the NOA type or choose not to manipulate the current value.
2.16.2.3.50.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.50.3 Values
Value Description
Spare Sets the type to Spare
Subscriber Sets the type to Subscriber
Unknown Sets the type to Unknown
National Sets the type to National
International Sets the type to International
Network Specific Sets the type to Network Specific
UK Specific Sets the type to UK Specific
Ignore/Leave Do not manipulate value
2.16.2.3.51 set_cdpn_strip
2.16.2.3.51.1 Description
Set the number of characters to strip from the CDPN
2.16.2.3.51.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.52 set_cdpn_prefix
2.16.2.3.52.1 Description
Set the characters to prefix the CDPN with
2.16.2.3.52.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.53 set_cgpn_Present
2.16.2.3.53.1 Description
Set whether the CGPN is expected to be present, not present or choose not to manipulate the
current value.
2.16.2.3.53.2 Definition
Applicable Modes User Type
All Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 109 of 124
Write No-Default
2.16.2.3.53.3 Values
Value Description
Present Set CGPN must be present
Absent Set CGPN must be absent
Leave Do not manipulate value
2.16.2.3.54 set_cgpn_National
2.16.2.3.54.1 Description
Set whether the CGPN is expected to be present, not present or choose not to manipulate the
current value.
2.16.2.3.54.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.54.3 Values
Value Description
National Set CGPN must be National
International Set CGPN must be International
Ignore/Leave Do not manipulate value
2.16.2.3.55 set_cgpn_RoutingInd
2.16.2.3.55.1 Description
Set whether the CGPN Routing Ind is expected to Route on GT, Route on SSN or choose not to
manipulate the current value.
2.16.2.3.55.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.55.3 Values
Value Description
National Set CGPN to Route on GT
International Set CGPN to Route on SSN
Ignore/Leave Do not manipulate value
2.16.2.3.56 set_cgpn_SSN_Present
2.16.2.3.56.1 Description
Set whether the SSN is expected to be present, not present or choose not to manipulate the current
value.
2.16.2.3.56.2 Definition
Applicable Modes User Type
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 110 of 124
All Read Write No-Default
Integer
2.16.2.3.56.3 Values
Value Description
Present Set SSN must be present
Absent Set SSN must be absent
Leave Do not manipulate value
2.16.2.3.57 set_cgpn_SSN
2.16.2.3.57.1 Description
Set the SSN is type or choose not to manipulate the current value.
2.16.2.3.57.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.57.3 Values
Value Description
ISUP Sets the type to ISUP
OMAP Sets the type to OMAP
MAP Sets the type to MAP
HLR Sets the type to HLR
VLR Sets the type to VLR
MSC Sets the type to MSC
EIC Sets the type to EIC
AUC Sets the type to AUC
ISDN SS Sets the type to ISDN SS
B-ISDN Sets the type to B-ISDN
TCtest Sets the type to TCtest
Ignore/Leave CGPN SSN can be any type, but will not count towards a best match total.
2.16.2.3.58 set_cgpn_Pointcode_Present
2.16.2.3.58.1 Description
Set whether the CGPN Pointcode is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.58.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.58.3 Values
Value Description
Present Set CGPN Pointcode must be present
Absent Set CGPN Pointcode must be absent
Leave Do not manipulate value
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 111 of 124
2.16.2.3.59 set_cgpn_Pointcode
Set the CGPN Pointcode or choose not to manipulate the current value.
2.16.2.3.59.1 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.59.2 Values
Value Description
Set CGPN Pointcode value
Leave Do not manipulate value
2.16.2.3.60 set_cgpn_GT_Present
2.16.2.3.60.1 Description
Set whether the CGPN Global Title is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.60.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.60.3 Values
Value Description
Present Set CGPN GT must be present
Absent Set CGPN GT must be absent
Leave Do not manipulate value
2.16.2.3.61 set_cgpn_NumberingPlan_Present
2.16.2.3.61.1 Description
Set whether the CGPN Numbering Plan is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.61.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.61.3 Values
Value Description
Present Set CGPN Numbering Plan must be present
Absent Set CGPN Numbering Plan must be absent
Leave Do not manipulate value
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 112 of 124
2.16.2.3.62 set_cgpn_NumberingPlan
2.16.2.3.62.1 Description
Set the Numbering Plan type or choose not to manipulate the current value.
2.16.2.3.62.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.62.3 Values
Value Description
Unknown Sets the type to Unknown
ISDN Sets the type to ISDN
Generic Sets the type to Generic
Data Sets the type to Data
Telex Sets the type to Telex
Maritime Mobile Sets the type to Maritime Mobile
Land Mobile Sets the type to Land Mobile
ISDN/mobile Sets the type to ISDN/mobile
Ignore/Leave Do not manipulate value
2.16.2.3.63 set_cgpn_TranslationType_Present
2.16.2.3.63.1 Description
Set whether the CGPN Numbering Plan is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.63.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.63.3 Values
Value Description
Present Set CGPN Translation Type must be present
Absent Set CGPN Translation Type must be absent
Leave Do not manipulate value
2.16.2.3.64 Set_cgpn_TranslationType
2.16.2.3.64.1 Description
Define the value expected or choose not to manipulate the current value.
2.16.2.3.64.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 113 of 124
2.16.2.3.64.3 Values
Value Description
set Translation Type value
Leave Do not manipulate value
2.16.2.3.65 set_cgpn_EncodingScheme_Present
2.16.2.3.65.1 Description
Set whether the CGPN Numbering Plan is expected to be present, not present or choose not to
manipulate the current value.
2.16.2.3.65.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.65.3 Values
Value Description
Present Set CGPN Encoding Scheme must be present
Absent Set CGPN Encoding Scheme must be absent
Leave Do not manipulate value
2.16.2.3.66 CGPN_ EncodingScheme
2.16.2.3.66.1 Description
Set the Encoding Scheme type or choose not to manipulate the current value.
2.16.2.3.66.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.66.3 Values
Value Description
Unknown Sets the type to Unknown
BCD Sets the type to BCD
National Sets the type to National
Ignore/Leave Do not manipulate value
2.16.2.3.67 set_cgpn_NOA_Present
2.16.2.3.67.1 Description
Set whether the CGPN NOA is expected to be present, not present or choose not to manipulate the
current value.
2.16.2.3.67.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 114 of 124
2.16.2.3.67.3 Values
Value Description
Present Set CGPN NOA must be present
Absent Set CGPN NOA must be absent
Leave Do not manipulate value
2.16.2.3.68 set_cgpn_ NOA
2.16.2.3.68.1 Description
Set the NOA type or choose not to manipulate the current value.
2.16.2.3.68.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.2.3.68.3 Values
Value Description
Spare Sets the type to Spare
Subscriber Sets the type to Subscriber
Unknown Sets the type to Unknown
National Sets the type to National
International Sets the type to International
Network Specific Sets the type to Network Specific
UK Specific Sets the type to UK Specific
Ignore/Leave Do not manipulate value
2.16.2.3.69 set_cgpn_strip
2.16.2.3.69.1 Description
Set the number of characters to strip from the CGPN
2.16.2.3.69.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.70 set_cgpn_prefix
2.16.2.3.70.1 Description
Set the characters to prefix the CGPN with
2.16.2.3.70.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.2.3.71 More SCCPLabels
2.16.2.3.71.1 Description
Add additional SCCP labels for best match routing/manipulation.
2.16.2.3.71.2 Definition
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 115 of 124
Applicable Modes User Type
All Read Resource Identifier
2.16.2.3.72 TCAPLabels
2.16.2.3.72.1 Description
Add TCAP labels for best match routing/manipulation.
2.16.2.3.72.2 Definition
Applicable Modes User Type
All Read Resource Identifier
2.16.2.3.73 MTP Route
2.16.2.3.73.1 Description
Add an MTP Route.
2.16.2.3.73.2 Definition
Applicable Modes User Type
All Read Resource Identifier
2.16.2.3.74 SSME Manipulation
2.16.2.3.74.1 Description
Check the SSME engine for any Map Manipulation required for the SCCP label. The Endpoint is
created from the SCCP Calling and Called Address
2.16.2.3.74.2 Definition
Applicable Modes User Type
All Read Write No-Default
Flag
2.16.2.3.74.3 Values
Value Description
On Check the SSME engine to perform MAP manipulation
Off No Manipulation required
2.16.2.3.75 Tx Msg/Sec
2.16.2.3.75.1 Description
Statistic showing real-time Messages/Second being sent matching this label.
2.16.2.3.75.2 Definition
Applicable Modes User Type
All Read Integer
2.16.2.3.76 Tx Msg/Sec Max
2.16.2.3.76.1 Description
Statistic showing maximum Messages/Second send rate since system start matching this label.
2.16.2.3.76.2 Definition
Applicable Modes User Type
All Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 116 of 124
2.16.2.3.77 Rx Msg Total
2.16.2.3.77.1 Description
Statistic showing total number of Messages received since system start.
2.16.2.3.77.2 Definition
Applicable Modes User Type
All Read Integer
2.16.2.3.78 Rx Msg/Sec
2.16.2.3.78.1 Description
Statistic showing real-time Messages/Second being received matching this label.
2.16.2.3.78.2 Definition
Applicable Modes User Type
All Read Integer
2.16.2.3.79 Rx Msg/Sec Max
2.16.2.3.79.1 Description
Statistic showing maximum Messages/Second receive rate since system start matching this label.
2.16.2.3.79.2 Definition
Applicable Modes User Type
All Read Integer
2.16.3 TCAP Label
2.16.3.1 Description
Resource used to define the TCAP label for best match routing/manipulation.
2.16.3.2 Products
SVI-STP
2.16.3.3 Attributes
2.16.3.3.1 Options
2.16.3.3.1.1 Definition
Applicable Modes User Type
All Read Write No-Default
Bit Mask Flag
2.16.3.3.1.2 Values
Value Description
SNMP-Trap If the resource changes state, an SNMP trap will be sent to the address configured on the debug resource.
2.16.3.3.2 Protocol
2.16.3.3.2.1 Description
Define the value expected or ignore the value.
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 117 of 124
2.16.3.3.2.2 Definition
Applicable Modes User Type
All Read Write No-Default
Integer
2.16.3.3.2.3 Values
Value Description
ITU CGPN Translation Type must be ITU
ANSI CGPN Translation Type must be ANSI
Ignore CGPN Translation Type can be ITU or ANSI, but will not count towards a best match total.
2.16.3.3.3 Primitive
2.16.3.3.3.1 Description
Define the Primitive type.
2.16.3.3.3.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.3.3.3.3 Values
Value Description
BEGIN Sets the type matched to BEGIN
END Sets the type matched to END
CONTINUE Sets the type matched to CONTINUE
UNI-DIRECTIONAL Sets the type matched to UNI-DIRECTIONAL
ABORT Sets the type matched to ABORT
Ignore Primitive can be any type, but will not count towards a best match total.
2.16.3.3.4 Component
2.16.3.3.4.1 Description
Define the Component type.
2.16.3.3.4.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.3.3.4.3 Values
Value Description
ITU Invoke Sets the type matched to ITU Invoke
ITU Return Result Sets the type matched to ITU Return Result
ITU Return Error Sets the type matched to ITU Return Error
ITU Reject Sets the type matched to ITU Reject
ITU Return Result NL Sets the type matched to ITU Return Result NL
ANSI Invoke Sets the type matched to ANSI Invoke
ANSI Return Result Sets the type matched to ANSI Return Result
ANSI Return Error Sets the type matched to ANSI Return Error
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 118 of 124
ANSI Reject Sets the type matched to ANSI Reject
Ignore Component can be any type, but will not count towards a best match total.
2.16.3.3.5 MAP_Operation_Code
2.16.3.3.5.1 Description
Define the MAP Operation Code type.
2.16.3.3.5.2 Definition
Applicable Modes User Type
All Links Read Write No-Default
Drop Down List
2.16.3.3.5.3 Values
Value Description
Insert Subscriber Data Sets the type matched to Insert Subscriber Data
Send Routing Info For SM Sets the type matched to Send Routing Info For SM
MP Forward Short Message Sets the type matched to MP Forward Short Message
Update Location Sets the type matched to Update Location
Cancel Location Sets the type matched to Cancel Location
Send IMSI Sets the type matched to Send IMSI
Send Routing Info Sets the type matched to Send Routing Info
Unstructured SS Notify Sets the type matched to Unstructured SS Notify
Inform Service Centre Sets the type matched to Inform Service Centre
Alert Service Centre Sets the type matched to Alert Service Centre
Alert Service Centre Without Result
Sets the type matched to Alert Service Centre Without Result
MT Forward Short Message Sets the type matched to MT Forward Short Message
MT AS MO Forward Short Message
Sets the type matched to MT AS MO Forward Short Message
Report SM Delivery Status Sets the type matched to Report SM Delivery Status
Set Message Waiting Data Sets the type matched to Set Message Waiting Data
Any Time Interrogation Sets the type matched to Any Time Interrogation
Ready For SM Sets the type matched to Ready For SM
Provide Subscriber Info Sets the type matched to Provide Subscriber Info
Ignore Component can be any type, but will not count towards a best match total.
2.16.3.3.6 More TCAPLabels
2.16.3.3.6.1 Description
Add additional TCAP labels for best match routing/manipulation.
2.16.3.3.6.2 Definition
Applicable Modes User Type
All Read Resource Identifier
2.16.3.3.7 Tx Msg/Sec
2.16.3.3.7.1 Description
Statistic showing real-time Messages/Second being sent matching this label.
2.16.3.3.7.2 Definition
Applicable Modes User Type
All Read Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 119 of 124
2.16.3.3.8 Tx Msg/Sec Max
2.16.3.3.8.1 Description
Statistic showing maximum Messages/Second send rate since system start matching this label.
2.16.3.3.8.2 Definition
Applicable Modes User Type
All Read Integer
2.16.3.3.9 Rx Msg Total
2.16.3.3.9.1 Description
Statistic showing total number of Messages received since system start.
2.16.3.3.9.2 Definition
Applicable Modes User Type
All Read Integer
2.16.3.3.10 Rx Msg/Sec
2.16.3.3.10.1 Description
Statistic showing real-time Messages/Second being received matching this label.
2.16.3.3.10.2 Definition
Applicable Modes User Type
All Read Integer
2.16.3.3.11 Rx Msg/Sec Max
2.16.3.3.11.1 Description
Statistic showing maximum Messages/Second receive rate since system start matching this label.
2.16.3.3.11.2 Definition
Applicable Modes User Type
All Read Integer
2.17 MTP CDR
2.17.1 Description
The MTP CDR Resource is used to configure the collection of SS7 MTPL3 CDR records. This resource
can be set against a SS7 Linkset resource, and controls the way that the SVI writes to the MTP CDR
text file.
The overall configuration of MTP CDRs is explained in SalesForce solution 529.
2.17.2 Products
SVI-MG | SVI-MGC | SVI-STP | SVI-SMSC | SVI-SG
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 120 of 124
2.17.3 Attributes
2.17.3.1 Status
2.17.3.1.1 Description Must be set to INS to function
2.17.3.1.2 Definition
Applicable Modes User Type
All Read Write
List
2.17.3.1.3 Values
Value Description
INS
2.17.3.2 Options
2.17.3.2.1 Description
Controls various behaviours
2.17.3.2.2 Definition
Applicable Modes User Type
All Read Write
List
2.17.3.2.3 Values
Value Description
Daily creates a new MTPCDR file every day (default is hourly)
Terminated RX/TX messages will be displayed differently in the CDR log. This should normally be enabled.
Threaded creates a separate thread for the MTP CDR logger
2.17.3.3 Sleep
2.17.3.3.1 Description
Controls how long a threaded MTP CDR task sleeps between activity
2.17.3.3.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.17.3.3.3 Values
Value Description
Any (ms) Value in milliseconds
2.17.3.4 Filesize
2.17.3.4.1 Description
Maximum size of a CDR file before it is closed and a new one created - old file will be given
extension .hh.mm.ssss when new one is created
2.17.3.4.2 Definition
Applicable Modes User Type
All Read Write
Integer
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 121 of 124
2.17.3.4.3 Values
Value Description
Any Value in bytes
2.17.3.5 Location
2.17.3.5.1 Description
Folder location where MTP CDRs will be located. Should be terminated with \
2.17.3.5.2 Definition
Applicable Modes User Type
All Read Write
String
2.17.3.5.3 Values
Value Description
Any Location (normally relative to /home/squire/)
2.17.3.6 MTP Filter
2.17.3.6.1 Description
The MTP Route resource used to filter which MTPL3 messages should be logged to the CDR file.
The MTP Route attributes linkset, OPC, DPC, SIO and NI can be used to filter messages.
2.17.3.6.2 Definition
Applicable Modes User Type
All Read Write
Resource
2.17.3.6.3 Values
Value Description
2.18 XML
2.18.1 Description
The XML Resource is used to configure the SSME for the SVI-STP, or the SSME for the SVI-SS
2.18.2 Products
SVI-STP
2.18.3 Attributes
2.18.3.1 Status
2.18.3.1.1 Description Must be set to Start to function
2.18.3.1.2 Definition
Applicable Modes User Type
All Read Write
List
2.18.3.1.3 Values
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 122 of 124
Value Description
INS
Start
2.18.3.2 Type
2.18.3.2.1 Description
Controls the type of the XML
2.18.3.2.2 Definition
Applicable Modes User Type
All Read Write
List
2.18.3.2.3 Values
Value Description
XML XML file to be used for the setup
2.18.3.3 File Type
2.18.3.3.1 Description
The type of file to be used, to setup the relevant SSME
2.18.3.3.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.18.3.3.3 Values
Value Description
STP_SSME_XML_FILE STP SSME to be setup
VLD_SSME_XML_FILE Voice Destination SSME to be setup
2.18.3.4 Validation Type
2.18.3.4.1 Description
The type of validation to be performed on the XML File
2.18.3.4.2 Definition
Applicable Modes User Type
All Read Write
Integer
2.18.3.4.3 Values
Value Description
VLD_XSD_SCHEMA XML file to be validated against the XSD Schema defined
2.18.3.5 Filename
2.18.3.5.1 Description
Location of XML File to be loaded
2.18.3.5.2 Definition
Applicable Modes User Type
All Read Write
String
2.18.3.5.3 Values
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 123 of 124
Value Description
Any Location (normally relative to /home/squire/)
2.18.3.6 Validation file
2.18.3.6.1 Description
The location of the XSD Schema
2.18.3.6.2 Definition
Applicable Modes User Type
All Read Write
Resource
2.18.3.6.3 Values
Value Description
Any Location of the XSD Schema relative to /home/squire Default if not set /home/squire/ssme/.schema
2.18.3.7 ssmeoptions
2.18.3.7.1 Description
Options to be used against the ssme xml resource
Controls various behaviours
2.18.3.7.2 Definition
Applicable Modes User Type
All Read Write
Resource
2.18.3.7.3 Values
Value Description
Validate On loading the XML file validate against the XSD Schema
New Output File Creates a new output file containing the results of testing and parsing
Run Tests Run tests on loading the XML file
Check Resource Names Confirms that the resource names in the XML file exist within the SVI-SS
2.18.3.8 ssmedebug
2.18.3.8.1 Description
Sets the SSME Debug level (XML task must be enabled)
2.18.3.8.2 Definition
Applicable Modes User Type
All Read Write
Resource
2.18.3.8.3 Values
Value Description
All All debug turned on
Critical Only critical debug is displayed
Eng Only engineering debug is displayed
Err Only Err debug is displayed
Info Only Info debug is displayed
Log Only log debug is displayed
SS7 Glossary Squire Technologies – Confidential Document
S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 124 of 124
2.18.3.9 Ssme threshold
2.18.3.9.1 Description
Sets the SSME threshold for look-ups in the SSME, if exceeded then the Input and Path is displayed
in the log file.
2.18.3.9.2 Definition
Applicable Modes User Type
All Read Write
Resource
2.18.3.9.3 Values
Value Description
Any Integer set in micro seconds
2.18.3.10 Max Time
2.18.3.10.1 Description
Shows the Maximum time of a call to the SSME. Set as micro sets
2.18.3.10.2 Definition
Applicable Modes User Type
All Read
Resource
2.18.3.10.3 Values
Value Description
Any Integer set in micro seconds
2.18.3.11 Show SSME Longest
2.18.3.11.1 Description
Only available via the telnet, shows the 10 longest ssme lookups in the system. Display input and
SSME path
2.18.3.11.2 Definition
Applicable Modes User Type
All Read
Resource
2.18.3.11.3 Values
Value Description
Any Integer set in micro seconds
top related