survey results for fire loads and live loads in office buildings
Post on 11-Sep-2021
10 Views
Preview:
TRANSCRIPT
NAFL INST OF STANDARDS & TECH R.I.C.
A1 11 00992948Culver, Charles/Survey results for fire
TA435 .U58 V85;1976 C.I NBS-PUB-C 1976
NBS BUILDING SCIENCE SERIES
U.S. DEPARTMENT OF COMMERCE / National Bureau of Standards
Survey Results for
Fire Loads and Live Loads
in Office Buildings
NATIONAL BUREAU OF STANDARDS
The National Bureau of Standards^ was established by an act of Congress March 3, 1901.
The Bureau's overall goal is to strengthen and advance the Nation's science and technology
and facilitate their effective application for public benefit. To this end, the Bureau conducts
research and provides: (1) a basis for the Nation's physical measurement system, (2) scientific
and technological services for industry and government, (3) a technical basis for equity in trade,
and (4) technical services to promote public safety. The Bureau consists of the Institute for
Basic Standards, the Institute .for Materials Research, the Institute for Applied Technology,
the Institute for Computer Sciences and Technology, and the Office for Information Programs.
THE INSTITUTE FOR BASIC STANDARDS provides the central basis within the United
States of a complete and consistent system of physical measurement; coordinates that system
with measurement systems of other nations; and furnishes essential services leading to accurate
and uniform physical measurements throughout the Nation's scientific community, industry,
and commerce. The Institute consists of the Office of Measurement Services, the Office of
Radiation Measurement and the following Center and divisions:
Applied Mathematics — Electricity — Mechanics — Heat — Optical Physics — Center
for Radiation Research: Nuclear Sciences; Applied Radiation — Laboratory Astrophysics^
— Cryogenics " — Electromagnetics - — Time and Frequency -.
THE INSTITUTE FOR MATERIALS RESEARCH conducts materials research leading to
improved methods of measurement, standards, and data on the properties of well-characterized
materials needed by industry, commerce, educational institutions, and Government; provides
advisory and research services to other Government agencies; and develops, produces, and
distributes standard reference materials. The Institute consists of the Office of Standard
Reference Materials, the Office of Air and Water Measurement, and the following divisions:
Analytical Chemistry — Polymers — Metallurgy — Inorganic Materials — Reactor
Radiation — Physical Chemistry.
THE INSTITUTE FOR APPLIED TECHNOLOGY provides technical services to promote
the use of available technology and to facilitate technological innovation in industry and
Government; cooperates with public and private organizations leading to the development of
technological standards (including mandatory safety standards), codes and methods of test;
and provides technical advice and services to Government agencies upon request. The Insti-
tute consists of the following divisions and Centers:
Standards Application and Analysis — Electronic Technology — Center for Consumer
Product Technology: Product Systems Analysis; Product Engineering — Center for Building
Technology: Structures, Materials, and Life Safety; Building Environment; Technical Evalua-
tion and Application — Center for Fire Research: Fire Science; Fire Safety Engineering.
THE INSTITUTE FOR COMPUTER SCIENCES AND TECHNOLOGY conducts research
and provides technical services designed to aid Government agencies in improving cost effec-
tiveness in the conduct of their programs through the selection, acquisition, and effective
utilization of automatic data processing equipment; and serves as the principal focus within
the executive branch for the development of Federal standards for automatic data processing
equipment, techniques, and computer languages. The Institute consists of the following
divisions:
Computer Services — Systems and Software — Computer Systems Engineering — Informa-
tion Technology.
THE OFFICE FOR INFORMATION PROGRAMS promotes optimum dissemination and
accessibility of scientific information generated within NBS and other agencies of the Federal
Government; promotes the development of the National Standard Reference Data System and
a system of information analysis centers dealing with the broader aspects of the National
Measurement System; provides appropriate services to ensure that the NBS staff has optimum
accessibility to the scientific information of the world. The Office consists of the following
organizational units:
Office of Standard Reference Data — Office of Information Activities — Office of Technical
Publications — Library — Office of International Relations — Office of International
Standards.
^ Headquarters and Laboratories at Gaithersburg, Maryland, unless otherwise noted; mailing address
Washington. D.C. 20234,
2 Located at Boulder, Colorado 80302.
Survey Results for Fire Loads and
Live Loads in Office Buildings
ATIUKAI. I,, , ,.,AU
m 2 1976
I
'M C. "1-
Charles G. Culver
Center for Building Technology
Institute for Applied Technology
National Bureau of Standards
Washington, D.C. 20234DATE DUE
Sponsored by
Public Buildings Service
General Services Administration
Washington, D.C. 20405
and
National Academy of Sciences
Building Research Advisory Board
2100 Pennsylvania Avenue
Washington, D.C. 20418
GAYLORD PRINTED IN U.S.A.
U.S. DEPARTMENT OF COMMERCE, Elliot L. Richardson, Secretary
James A. Baker, III, Under Secretary
Dr. Betsy Ancker-Johnson, Assisfani Secretary for Science and Technology
NATIONAL BUREAU OF STANDARDS, Ernest Ambler, Aciing Director
Issued May 1976
Library of Congress Cataloging in Publication Data
Culver, Charles.
Survey results for fire loads and live loads in office buildings.
(NBS building science series ; 85)
"Prepared by the Office of Housing and Building Technology, Center
for Building Technology, Institute for Applied Technology, National
Bureau of Standards, Washington, D. C."
Bibliography: p.
Supt.ofDocs.no.: C13.29/2:85
1. Office buildings—Fires and fire prevention. 2. Office buildings
—
Live loads. 3. Building Research—United States. I. National Research
Council. Building Research Advisory Board. II. Center for BuildingTech-
nology. Office of Housing and BuildingTechnology. III. Title. IV. Series:
United States. National Bureau of Standards. Buildingscience series ; 85.
TA435.U58 no. 85 (TH9445.041 690'.021s [690'5] 76-608115
National Bureau of Standards Building Science Series 85
Nat. Bur. Stand. (U.S.), Bldg. Sci. Ser. 85, 157 pages (May 1976)
CODEN: BSSNBV
U.S. GOVERNMENT PRINTING OFFICEWASHINGTON: 1976
For sale by the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402
(Order by SD Catalog No. C13.29/2:85). Price $2.25 (Add 25 percent additional for other than U.S. mailing).
PREFACE
This report was prepared by the Office of Housing and Building Technology,Center for Building Technology, Institute for Applied Technology, NationalBureau of Standards, Washington, D.C. under Subcontract No. BRAB 27-73-53
between the National Academy of Sciences and the National Bureau of
Standards. The data on fire loads and live loads presented herein wereobtained from a survey of office buildings conducted by the National Bureauof Standards during the period August 1974 through August 1975.
The program of which this work is a part is being sponsored by the PublicBuildings Service, General Services Administration, under contract between
GSA and the National Academy of Sciences.
iii
ABSTRACT
Fire load and live load data obtained from a survey of 23 office buildingslocated in various regions throughout the United States are presented. Thesurvey design is described including the characteristics of the buildingpopulation used to select the sample. Data are presented on the magnitudeand distribution of the loads. Information is also included on the charac-teristics of office loads such as the type of items (furniture, equipment,etc.) and their properties (material type, dimensions, exposure, etc.).Statistical summaries of the data and a determination of the building andoccupancy characteristics affecting these loads are presented. The data do
not indicate any significant differences between the loads in private and
government buildings. Similarly, geographic location, building height, and
building age were not found to have a significant influence on load magnitude.The use of the rooms surveyed, however, did affect load magnitude. A
mathematical model developed from a regression analysis of the survey data
is presented for calculating fire loads and live loads in offices. The data
presented may be used to evaluate current requirements for design loads for
buildings.
Key words: Buildings; fire loads; load surveys; occupancy live loads;
structural engineering.
iv
SI CONVERSION UNITS
In recognition of the position of the U.S.A. as a signatory to the General
Conference of Weights and Measures, which gave official status to the
metric SI system of units in 1960, the author assists readers interestedin making use of the coherent system of SI units by giving conversion
factors applicable to U.S. units used in this paper.
Length
1 in = 0.0254* meter1 ft - 0.3048* meter
Area
1 in^ = 6.4516* x 10"! meter^1 ft = 0.09290 meter
Force
1 lb (Ibf) = 4.448 newton
Pressure, Stress
1 psf = 47.88 pascal
Thermal
1 Btu = 1.054 X 10^ joule
* Exactly
V
TABLE OF CONTENTS
Page
PREFACE iii
ABSTRACT iv
SI CONVERSION UNITS v
1. INTRODUCTION 1
2. SURVEY DESIGN 2
2.1 General 2
2.2 Survey Data 2
2.3 Sampl ing Plan 6
2.4 Data Collection and Processing 9
3. DATA ANALYSIS 15
3.1 General 15
3.2 Evaluation of Inventory Technique 16
3.3 Characteristics of Survey Sample . 493.4 Influence of Building Characteristics 563.5 Influence of Occupant Characteristics 61
3.6 Influence of Room Characteristics 773.7 General Results 973.8 Load Models 1143.9 Evaluation of Load Models 117
4. SUMMARY AND CONCLUSIONS 125
5. RESEARCH RECOMMENDATIONS 127
6. ACKNOWLEDGMENTS 129
7. REFERENCES 130
8. APPENDIX - Structural Influence of Live Load Locations ... 132
vii
1. INTRODUCTION
In order to evaluate the effect of fires on buildings, it is necessaryto estimate the potential severity of such fires in addition to the fireresistance of the construction. Tests have shown that there is a definiterelationship between the weight of the combustible contents or fire loadin a building and the resulting fire severity. The nature of the combus-tible contents is also important in connection with hazards such as rapidflame spread and smoke generation. Similarly, live load or the weight ofall the contents is needed for the structural design of buildings. Require-ments for minimum loads for use in design are based on data obtained fromload surveys.
Since construction practices evolve over the years and the nature of buildingcontents change, there is a continuing need to update load survey data toreflect current conditions. Recognizing this, the National Commission onFire Prevention and Control recommended that: "...the fuel (fire) loadstudy sponsored by the General Services Administration and conducted by theNational Bureau of Standards be expanded to update the technical study ofoccupancy fire loads." (1)* Similarly, researchers have pointed out theneed for appropriate survey data for use in connection with statistical studiesof load variability and the development of probabilistic design approaches (2).
In 1973, the General Services Administration (GSA), the National Academyof Sciences (NAS), and the National Bureau of Standards (NBS) initiated a
survey project to determine fire loads and live loads in office buildings.The project represented a continuation of the load survey activities carriedout by NBS since 1928 (3,4).
One objective of the project was to identify the building characteristicsand occupancy characteristics which affect the magnitude of fire loads and
live loads in office buildings and develop mathematical models for predictingfuture loads. Development of these mathematical models expressing the rela-tionship between the factors and loads would facilitate establishing futureminimum design requirements and minimize the necessity for continued load
surveys. A second objective was to develop efficient, economic, reliable datacollection and data processing procedures applicable to a wide class of
buildings of differing occupancy type. This would permit the methodologydeveloped in the project for office buildings to be used for surveys of
occupancies such as hospitals, schools, etc.
This report summarizes the survey design, including selection of the surveysample, and describes the type of data collected and the data processingprocedure. Data obtained from the survey of 23 office buildings are presentedalong with results of the analysis identifying the influence of various factors
on load magnitude.
* Figures in parentheses refer to references listed in Chapter 7.
1
2. SURVEY DESIGN
2.1 General
A complete description of the considerations involved in planning the surveywas presented in an earlier report (5) and will, therefore, only be summarizedhere. The objective of the project was to determine those factors whichaffect the magnitudes of loads in buildings. Using the survey data, proba-bilistic models could then be developed to predict loads in buildings basedon these factors. Based on results from previous studies and considerationof all the various factors which could affect load magnitude, the factorsdiscussed in Section 2.2 were selected.
It was necessary to limit the number of factors studied in order to obtain a
reasonable sample size for the survey. Since considerable judgment wasinvolved in selecting these factors, a two phase effort was planned. Thefirst phase was designed to identify the important factors in the list of
all factors initially judged to be potentially significant. The second phasewould then concentrate on these important factors. Prior to initiating the
first phase, the special survey techniques developed for this project werepretested in a pilot survey involving the NBS Administration Building.
Data obtained from the pilot survey and Phase I are included in this report.
Recommendations for additional types of analysis using this data and con-
siderations involved in planning a second phase survey are presented in
Chapter 5. The scope of the second phase will be determined at a later date.
2.2 Survey Data
The factors selected for investigation in Phase I which may affect the
magnitude of fire and live loads in buildings included:
1 . Bui Iding location2. Building height3. Bui Iding age4. Occupancy characteristics5. Room use
6. Room size
The type of survey data collected is listed in Figure 1. This includedthe above factors, information of interest to fire protection engineersin connection with fire severity, and the magnitude and distribution of
fire and live loads.
The fire and live loads were limited to those resulting from the intended use
of the building. This included furniture, equipment, and other items broughtin for the service of the occupants after construction of the building.
Data were obtained on the normal number of occupants but no informationon their weight was collected or included in computing the loads. Walls and
2
oo
CD tZ
bU hAd00 !^ Q- oZD 00 O O• • • •
iJ ' ' '
I
-I oJj
r
COccUJI—
<<
CD
O5<
<a.
C^ 2 -CZ oo a
COCJ
a
>
Q.
O.
>
2 I- PO S L±J oQ UJ CD OS a: < o
3
full height partitions, including removable partitions affixed to the floorand ceiling, doors, and windows were not considered for the case of live loador fire load. Combustible finish materials, including paneling, paint, andwallpaper for walls and full height partitions, ceiling and flooring finishmaterials and trim such as wooden molding on walls, doors, and windows wereincluded only for fire loads. Loads due to partial height partitions usedto subdivide larger areas into work stations were included for both fireand live loads.
The areas within the buildings for which loads were considered were restrictedto offices and related work areas. Corridors, lavatories, mechanical equip-ment facilities, elevators, etc. were not included, however, their locationswere recorded. Similarly, basements (i.e. the portion of the building com-pletely below grade) were also not included. Although loads for these areasare important, it was not feasible to include them in the scope of this project.
The pilot survey data were collected over a two-week period of time and thePhase I data over a six-month period and no attempt was made to monitor thechange in load with time in a given area. Since the occupancy duration foreach area was recorded, however, it was possible to determine the influenceof this factor on the load magnitude. Data for the NBS AdministrationBuilding could also be compared with data obtained in a survey conducted in
1967 (4). The data also permitted determining the effect of the age of thebuilding on the load magnitude.
Loads were determined for only some of the rooms in the surveyed buildingsin order to reduce the field survey effort and still include a large numberof buildings. It was assumed that probabilistic models developed from the
data could then be used to predict the loads in the unsurveyed rooms.
Following this, studies of loads throughout the building could be made.Horizontal and vertical correlations of loads and determination of loads
on entire floors, etc. would be possible. Sufficient data were obtained,therefore, to permit extrapolating the results obtained from the surveyedrooms to other areas of similar use within the buildings.
An inventory survey technique employing the collection of data on the physicalcharacteristics of the various room content items was used in this survey.
The data collected for each item included: type of item (desk, table, etc.);
the construction material (wood, metal, etc.); measured dimensions (length,
width, height). For irregular shaped items and irregular piles of paperapproximate dimensions were recorded. Weights for each item were then obtainedusing "average" weights established from manufacturers data for items of
similar size and construction. This concept is illustrated in Figure 2 in
which the "average" weights are referred to as transfer functions. For small
miscellaneous items and equipment, the weight was estimated by the surveyorin lieu of using transfer functions. These transfer functions were presentedin an earlier report (5). No direct weighing was used in the survey. This
inventory procedure was less time consuming than direct weighing and caused a
minimum disruption of the normal business activities in the surveyed rooms.
In addition, the inventory procedure provided considerable information on
4
LULl_ OCO 1—
<GC1— LL-
-»->
Q.<UOco(_)
>>0)>
>)s-oc>
the characteristics of office contents (material type, dimensions, com-bustibility, etc.) for use in connection with fire related studies. An
evaluation of the accuracy for the weight of items obtained using this pro-cedure is given in Section 3.2.
Only the proximity of items in the rooms with respect to the walls andnot their exact location was recorded. Studies indicated that thisprocedure was satisfactory for determining the influence of fire load on
structural components (5). Analysis of the influence of this procedurein evaluating live load effects for design of the structural system is
included in the Appendix.
2.3 Sampling Plan
The objective of the first phase of the program was to investigate theinfluence of the building and occupancy factors discussed in Section 2.2and identify the more important ones. Subdividing the current U.S. officebuilding population into smaller subpopulations grouped according to
building height, age, etc., and sampling from each group would permit deter-mining the mean values of the loads for the total population using a weightedsum of the mean loads obtained for each subpopulation. These mean valuesfor each subpopulation could also be used for estimating values for futurebuilding populations which are of primary interest for building code purposessimply by changing the weighting factors.
Since a complete inventory of the U.S. office building population listing the
characteristics of interest in this study does not exist, available listswere used to select the buildings in the survey. A list of private buildingsobtained from the Building Owners and Managers Association (BOMA), an associa-tion of independent building owners, and a list of government buildings obtainedfrom the General Services Administration (GSA) were used. In addition to
representing different occupancies, private and government, the BOMA and GSA
buildings represent two types of occupancy control. Whereas the GSA buildingsare completely controlled and involve occupancy by similar tenants, the BOMA
buildings are multi-tenant rental buildings with less control over tenantusage of the building.
The height, age, and geographical distribution for these two populations are
given in Tables 1 and 2. Originally, twenty private buildings and five
government buildings were randomly selected for survey from these lists using
the concept of a factorial experiment design (5). Three factors (geographiclocation, height, age) each having four "levels" were involved. The four
census regions for the U.S. were used for geographic location and five story
and five year increments were used for height and age. A one-fourth fractionof a 4^ factorial experiment was used for the private building (7). Charac-
teristics for the buildings selected were presented in an earlier report (5).
Unfortunately, considerable difficulty was encountered in securing survey
permission for randomly selected private buildings, and only twelve wereobtained from the BOMA list. Although specific reasons were not given by
those refusing to participate, apprehension concerning disruption of thenormal business activities in the offices and the potential use of the surveyresults may have accounted for their reluctance. Survey permission for addi-tional private buildings was obtained by working through city building
6
TABLE 1 CHARACTERISTICS OF BOMA OFFICE BUILDING INVENTORY
Geographic Location*Hpi nht Rrniin Age Group
West( Years
)
Northeast Northcentral South
1- 5 1 13 26 15
1- 5 6-10 1 18 1
7
9
1 1-20 7 14 21 9
>20 7 22 57 17
1- 5 1 5 9 8
6-10 6-10 3 8 10 7
1 1 -20 4 1
3
1 b 7
>20 8 69 54 49
1- 5 1 6 9 3
11-20 6-10 1 11 14 6
11-20 5 9on 9
>20 21 102 54 41
1- 5 1 14 12 7
>20 6-10 2 9 7 7
11-20 2 9 7 8
>20 17 66 25 9
TOTALS 82 388 357 211
*Values listed represent number of buildings in each category.
Total number of office buildings available in BOMA inventory - 1,038.
7
TABLE 2 CHARACTERISTICS OF GSA OFFICE BUILDING INVENTORY
Geographic Location*Height Group Age Group
(No. of Stories) (Years) Northeast Northcentral South West
1- 5 0 12 16 7
1- 5 6-10 4 10 25 17
1 1-20 0 12 27 7
>20 62 125 259 122
1- 5 0 5 4 0
6-10 6-10 3 1 8 8
1 1-20 2 4 10 3
>20 16 11 63 13
1- 5 1 0 1 1
11-20 6-10 1 c q 4
11-20 1 1 5 0
>20 10 11 8 5
1- 5 0 0 0 0
>20 6-10 2 3 0 1
11-20 0 0 0 0
>20 3 2 1 1
TOTALS 105 199 436 189
*Values listed represent number of buildings in each category obtained from
1974 GSA RICOS data file.
Total number of office buildings available in GSA inventory - 929.
8
officials. Due to difficulties in obtaining survey permission, only fouradditional buildings were obtained giving a total of sixteen private buildings.One additional government building was selected increasing the total numberof buildings, including the NBS Administration Building used for the pilotsurvey, to twenty-three.
The characteristics of the buildings surveyed are given in Table 3 andthe geographic distribution is shown in Figure 3. The NBS AdministrationBuilding used in the pilot survey is included in the list. The selectionprocedure for each building is indicated. The random selection refers to
buildings randomly selected from the GSA and BOMA lists. In some caseswhere permission could not be obtained for the first building selected froma given group, a second or third alternate was randomly selected. Theseare denoted as "Random (2)" or "Random (3)" to indicate that they were notthe first building chosen. The buildings not selected from the BOMA listas well as the additional government building from the GSA list are denotedas "Special." The height group, age group, and geographic locations aresummarized in Table 4.
The list of buildings presented in Table 3 differs from that included in an
earlier report (5). This is due to the difficulties with survey permissionnoted previously. Some of the buildings in the original sample withdrewtheir permission. Note that the building numbers in Table 3 are not sequential.It was impractical to reassign sequential numbers to the buildings after a
cancellation was received since this would have required adjustments to all
the data sheets. Building 27 was added to the original sample to increasethe number of rooms surveyed in this phase of the program to the desiredlevel of approximately 2,500. This affected the factorial experiment design
as indicated by the data in Table 4 and a one-fourth fraction was not achieved.
The effect of this on the analysis of the factors affecting load magnitude is
discussed in Section 3.8.
A sampling plan was developed to select the rooms to be surveyed in the
buildings (5). The plan was developed to obtain information on the influ-
ence of room use, occupancy characteristics, and room size on load magnitude.
After classifying all areas in the buildings in accordance with these factors,
the rooms in each group were randomly selected and surveyed. Data on these
factors for the buildings surveyed are included in Section 3.3. Since the
total number of rooms in all the buildings was less than originally estimated,
it was possible to increase the fifteen percent sampling rate initially
selected (5). Approximately twenty-five percent of the rooms in each building
were surveyed except for Buildings 14, 24, and 27. A larger sampling rate
was used for these buildings for reasons discussed in Section 3.3.
2.4. Data Collection and Processing
The data collected in the field surveys are described in an earlier report (5).
Complete documentation of the computer programs developed for processing these
data is also available (6).
The field survey operation involved two visits to each building. During the
first visit, information on the characteris'tics of the building and occupantswas collected. Floor plans were used to record data for all areas in the
building. This data was then used to select the specific offices to be sur-veyed in accordance with the established sampling plan. During the secondvisit, detailed data were collected to obtain the fire loads and live loads
for these rooms.
9
TABLE 3 BUILDING CHARACTERISTICS OF SURVEY SAMPLE
Location Height
Bldg. Occupancy (No. of Age Method of
No.* Type Region State Stories) (Years) Selectionk-k-k
1 PA 5 13 Random (2)
2 North- NY 7 58 Random
3 East PA 21 68 Random
5 PA 25 23 Random (3)
7 lA 5 16 Random
8 North- IL 5 2 Special
9 Central WI 20 1
0
Random (2)
10 Private T1
i L 23 1
6
Random
n OK 2 8 Random
12 South GA 10 73 Special
13 GA 10 5 Random (3)
14 OK 22 25 Special
1 7 WA 9 1
1
Random (3)
18 West AZ 17 13 Random (3)
19 111 AWA 49 5 Random
CA 5 63 Spec i a 1
21 North- PA 3 47 Random
22 East NY 44 7 Random
23 North-Government Central IL 2 7 Random
24** South MD 12 11
25 GA 4 6 Random
26 West CO 2 3 Random
27 CA 18 6 Special
*Buil dings not numbered sequentially**NBS Administration Building
***Random - Original random selection from BOMA and GSA lists
Random (2), (3) - Alternate random selection from BOMA and GSA lists
Special - Not randomly selected
10.
TABLE 4 HEIGHT AND AGE GROUPINGFOR BUILDINGS SURVEYED
A. Private Buildings
Height(No. of
Stories)
Geographic Location
Northeast Northcentral South West
1 - 5
6 - 10
11-20> 20
1 (III)
1 (IV)
0
2 (IV, IV)
2 (I, III)
0
1 (II)
1 (III)
1 (II)
2 (I, IV)
0
1 (IV)
1 (IV)
1 (III)
1 (III)
1 (I)
B. Government Buildings
Height(No. of
Stories)
Geographic Location
Northeast Northcentral South West
1 - 5
6-1011-20
> 20
1 (IV)
0
0
1 (II)
1 (II)
0
0
0
1 (II)
0
1*(III)0
1 (III)
0
1 (II)
0
* NBS Administration Building
( ) Age GroupI - 1 - 5 yearsII - 6-10 yearsIII - n - 20 yearsIV - > 20 years
12
The major portion of the data was recorded on specially developed FOSDIC(nim Optical S^canning D^evice for J[nput to C^omputers) data forms. Theseforms facilitated data collection and expedited the processing effortsince they were automatically processed without additional coding or trans-cription. Microfilming these documents provided a permanent record of thedata.
All the survey data were collected by a professional engineering firmworking under the general supervision of NBS staff. Technicians witha background in engineering or architecture performed the room surveysunder direct supervision of qualified engineers. Each surveyor was pro-vided with detailed instructions for collecting the data (5) and advisedof the significance of the survey and the manner in which the data wouldbe used. A short summary version of these instructions was provided foruse as a ready reference should questions arise during conduct of the survey.The supervisors provided approximately a ten-hour instruction period foreach surveyor to demonstrate the survey procedure and then answered questionsarising during conduct of the survey. Minimal supervision and field checkingof the data collection forms were required following this initial training.An average time of less than one man-hour was required to survey each room.This was less than half the time required in a previous survey in which theroom contents were weighed (4). One man was required for these room surveysas opposed to the four man survey team required to perform the weighing. No
special equipment was required and the only disturbance of the occupants of
the room involved opening drawers to ascertain the nature and weight of the
contents. The only information obtained from the occupants was the numberof individuals normally occupying the room.
Special steps were taken to validate and check the data prior to analysis.A one percent validation sample was randomly selected from the total list
of rooms surveyed in all the buildings. Following the survey, NBS staff
contacted the occupants of these rooms by phone to verify that the surveyhad been conducted in accordance with the established procedure. In addition,
the actual data collected for the room were checked with the occupant to
insure that it had been properly recorded. Satisfactory verification was
obtained for the survey procedures used and the data collected.
A special purpose computer program was written to check the data. The programwas used to detect mechanical errors resulting from automatic processing of
the data collection forms and verify that all the required data were collectedfor each item of furniture, equipment, etc. The program also checked the
data against specified tolerance limits to insure that the data were recorded
properly, e.g. furniture item dimensions were compared with the dimensions
of the room to check compatibility, etc. All data errors detected by the
computer were flagged and recorded. Minor errors such as the omission of
one piece of information for an item were corrected by the computer program
using pre-programmed values (6). When errors occurred in significant data
such as room dimensions, all the information for that room was discarded
13
prior to analysis. The errors which occurred were either oversights in
which some information for a particular item was not recorded or the dimen-sions were incorrectly marked on the form. The majority of errors wereincorrectly recorded dimensions. There was no apparent trend to theseerrors, i.e. they did not seem to be related to room use, building height,building age, etc. There were no errors due to misinterpretation of thesurvey instructions. Of the 2,433 rooms selected, 207 or 8.5 percent werediscarded due to errors in significant data.
Initial data processing was done using the digital computer facilities at
the National Bureau of Standards and the FOSDIC equipment of the Bureau of
the Census. Data reduction and data analysis were performed by the J. H.
Wiggins Company under direction and supervision of NBS professional staff.
A permanent record of all the original field survey data was retained on
microfilm. This information will be available for continuing studies and
analyses
.
14
3. DATA ANALYSIS
3.1 General
The analysis included in this report represents only a first step inutilization of the survey data. It is anticipated that the data baseobtained in this survey will be used by GSA, NBS, and others in a variety ofcontinuing studies of the loads in buildings. In addition to routineanalysis, parameter studies could be carried out, e.g. the impact of changesin office furnishings on fire loads in the buildings surveyed could bedetermined by modifying the survey data. Such studies will improve ourunderstanding of loads in buildings and facilitate the design of safeeconomical structures.
The following types of data analysis are included in this chapter:
(1) Evaluation of the inventory survey technique(2) Determination of the factors affecting load magnitudes(3) General data analysis
(4) Development and evaluation of mathematical models forpredicting loads
Data obtained from the pilot survey of the NBS Administration Building arecompared with direct weight measurements in Section 3.2. The character-istics of the survey sample are given in Section 3.3. The influence of
building characteristics, occupant characteristics, and room characteristicson load magnitudes is discussed in Sections 3.4, 3.5, and 3.6. Generalresults illustrating the variety of analyses possible using the survey dataare included in Section 3.7. Section 3.8 includes results obtained from a
regression analysis of the survey data relating load magnitudes and theparameters identified in this survey which affect loads in office buildings.An evaluation of the use of these load models to predict loads in buildingsis presented in Section 3.9.
In computing the live loads presented in subsequent sections of this chapter,the weights of furniture, equipment, and their contents were included. The
weight of the occupants of the room was not included. The weight of full
height partitions was not included. The weight of partial height partitionsused to subdivide large areas into work stations was included. Fire loads
include the weight of combustible room contents plus the weight of combustiblefinish materials for walls, ceilings, and floors. In some cases, these two
components of the total fire load are presented separately and referred to as
"movable contents" (furniture, equipment, etc.) and "interior finish" (walls,
ceilings, etc.). The fire loads in this report represent the total weightof combustibles and were obtained by converting the item weights to
equivalent weights of combustibles having a calorific value of 8000 Btu/lb.
The conversion factors used were presented in a previous report (5).
Derated fire loads can be computed from the data. In computing these derated
fire loads, the weights for enclosed combustibles such as paper in metal
filing cabinets can be adjusted using a derating factor or an estimate of
the amount of the material which will burn in a fire (17).
15
3.2 Evaluation of Inventory Technique
Since the survey technique adopted for this project has not been usedpreviously in a major survey, it was necessary to determine how well thevalues obtained for the total load in a room compare with those obtainedby direct weighing. Room loads obtained using the inventory techniquewill differ from measured loads for two reasons. First, the numericalvalues in the transfer functions used to convert the inventory data to
weight represent mean values for the item groups. Thus, unless the weightof each item in a given room equals the mean weight for that item group,the weights will differ. Second, the survey technique requires some estima-tion on the part of the surveyor, e.g. weight estimation for miscellaneousitems and approximation of "average" sizes and the height of irregular pilesfor paper and books for use in the transfer functions. These same kinds ofapproximations occurred in the Bryson and Gross (4) and Mitchell (8) surveys.Although they obtained "exact" values for the total load in a room, theweight of the contents of drawers, etc. were estimated. Whereas, the approxi-mations in this survey affect both the fire load and live load, approximationsin the surveys involving direct weighing affect only fire loads.
The NBS Administration Building was selected to evaluate the inventory tech-nique. This building was chosen for convenience and also because weighingoperations could be scheduled to provide minimum disruption of the normal
business activities. One hundred and fifty-nine rooms were surveyed in thebuilding. Fourteen of these rooms were randomly selected and, followingthe inventory survey, a follow-up survey involving weighing of all the roomcontents was conducted. These 14 rooms were either general or clericaloffices. These same rooms were also resurveyed several times by differentsurveyors using the inventory technique to establish the variability betweensurveyors. The weighing was conducted immediately following the inventorysurvey to insure that the room contents were the same for both surveys. This
weighing was done with the same equipment used in the survey of the buildingcarried out i n 1 967 (4)
.
A comparison of results obtained for the two surveys is given in Table 5. The
floor number and room number given correspond to the identification schemeused in conducting the survey. The numbers in parentheses correspond to the
room numbers assigned by the tenant. For the 14 rooms, there are 50 inventorysurveys by seven surveyors. Each room was surveyed at least three times by
three different surveyors. The total weight obtained from the weighing surveyand inventory weights obtained by the various surveyors are given for each
room. The percent difference between these values and between the measuredweight and the mean of the weight obtained by the surveyors for a given roomare also given. Note that the inventory weights for the various surveyors in
any one room are not exactly the same. Also for Room 527 (Floor 6, Room 24),Surveyor 002 surveyed this room twice and obtained two slightly differentvalues. Before comparing the measured and inventory weights, it is of interestto look at the reasons for these differences.
16
00
U. XIO ct
O CQ
0CJ 0u
+-> c:cz cu X CO LCI Ln Ln CMOJ ^- •
—
to CTl CTv 0 LD cricu
^ M— CO 0 1
—
1
—
0 CM^— CM1
Q_ 11
^—
'
1~
—
1
>)> S- (/)
CD 0 004-^ -C -—
^
4— d CO 0 0 Ln CD0 1— 1 CO CM CTlTD > CU —•' C\J t~ 1
— CM4-*
OO t-H
>>
0+-> JC '—
-
to CO Ln 'CO CM 00fO CD J3 0 00 1
—
CO 00 CM CM0) OJ 1— 1
—
00 tn 1
—
en 1^ Ln Ln> <u ' CM '
—
CO CM CM CO3
0OJ 00
+-> c<D X
<D i-dJ 1 0 00 00 1— 00 CM 1— CO LD CM 0 0 LO LD Ln >=d- Ln CO 0 CM*4— C\J ' CM CM CM '
—
CD 4— ^'—
'
1 1 • 1 1 1 1 1
Q- 1Q1—
'
1
>i
^— 0 -t->
03 +-) JZ -—
-
00 LD 1
—
LD CM CM CO "=1- CO CJ^ CM CO CO Ln 00 cr> 00 0 LD 00+J CD JO un 00 CO to — CM CM CTv Ln CO 0 CM CM 0 CO Ln ^ 000 •r— n— CM 00 CO 0 r— CO cn CTl 00 Ln 00 r-- Ln LO CO Ln Ln Ln CTv 00 CO1— > CU -
' CM CM C\J 1 n— 1 CO CO CO CM CM CM CM CM CM CO CO CO
I—
»
3
CM Ln CM ID ^ ^ 1^ Ln CM I— CM Ln' ^ CM "£?
f—
1
0 0 0 0 d> CD CD 000 0 0 0 0 0 0 CD CD CD0 0 000 (—^ ^5 Q 0 0 0 0 0 0 0 0 CD CD
T3CU +->
S- ^ —
^
CO 00 CO CO Ln 0CD-Q 0 >=a- Ln CO
l/l Ln CTl 0 LO COfO CU CM CO CM CM COOJ 3
'—
^
CMCU +-> 0 0 0 0 0 CO
1
[ CO 00 CO 00<C
CO 0 CO CM CO CO 0 CO «^ CDCM^ CM -—
-
CO CME • S- =a- S- CO S- 1— S- o-i s_ Ln s_ CO S-0 0 0 E CM 0 E cvj 0 E CO 0 E CO 0 E 0 0 E 0 E CM0 ^ 0 0 CM 0 0 CM 0 0 CM 0 0 CM 0 0 CO 0 0 CO 0 0 CO
0 0 ,— 0 —
•
0 0 .— 0 .— 0u_ u_ Li_ a: Li_ CC LU q; ll. q; U- cc
!
i
17
oo
c O)O) s-
S- M-0) 4-D. •-
> S_ 1/1
QJ O +->Q -!-> ^ --^
• O CU -r- 1—"D > CU—
-
00 H-i
o
o OCM•=1-
00
cn
CM
O
Ln
s_o +->
sr +-> j:z—
.
n3 c: cn J2CU O) -1-
I
—
2: > OJ^C IS
ro
CO
ro
CM
un
cr.
00
-a
c
oo
UJ
CUuCUs_CU
S_ C4-
CU M-Cl. -r-Q
OO
CUID IJD '— O UO C£) C\J CM f-^ OO
1— CM CM roI— I— Ln un CO CM CM <£)
CM CM ro CM
>>s_
.— O -!->
fO -t-> -C^+-> c cnj3O CU -r- n-1— > O)^
CM CM 00 1
—
C3~i ro I— CMCM CO COro ro CM CM
CM O ^
—
r— <Ti ^ cnCO 1— Ln roCM ro CM ro
Ln o Ln CM— 1— r—r-^ O o I—1— CM CM CM
00 o I
—
ro o CO Ln COCO o I
—
ro ^ ro ro ro
CO cn CTi "=!•
CM 'd- OCO Ln CO CO
o>>CU>i-
O 1— LOo o o oo o o oO r— CMo o o oo o o o
O I— CM <=J-o o o oo o o oO >— CM roo o o o oo o o o o
I— CM roo o o oo o o o
-aCU +->
S- -!Z
l/l -I- 1
—
(13 CU<U 3
CM roOro
1-^
CTi
ro CMCU +->
S- 4-<
roCO I
—
COCM
O Oo z:
Ln oro -—
^
S_ CTi
o E .—o o ^I— o -
—
U_ £
Ln oS- CMO E CMo o1— O '
Ln 00CM -—
-
s- roO E CMO Or— O
CO COCM -—
-
s_ roO E CMo o Ln,— o-~^
CO (—
LDO E CMo o Ln.— o -
—
Lj_ CU
18
"ence
X
100
-
0.18 0.45o a> ' '-^1. M- ro0) 4- -—
-
Q- •.- 1Q1^
1
Std.
Dev.
of Inventory
Weights(lb) (4)
Uf)
CM COCM
Mean Inventory Weight(lb) (3) 2207 3339
;nt
-•ence
X
100
Ln 1— CM
1 I
CM Ln CO oo
1 1 1
o <u ' ^S- M- CMCU 4-Q. •!-
1
1 1
TotalInventory Weight(lb) (2)
CM Ln CM1— LO Ln oCO O 1— COCM CM CM CM
Ln en CM cT^
CO CM CMLn C3^ "d-
CO CO CM CO
Surveyor
1— CM CMo o o oo o o o1— CM Ln ix>o o o oo o o o
Measured Weight(lb) (1) 2203 3354
cu -•->
S- 4-<: —
Room NnFloor
6
Room
24
(527)
Floor
7
Room
13
(634)
cn cy\
c\j cr> 1
—
O «^ CO
OJ ro c\J
csj cn
C\J OJ
r- CO
LO CNJ
CO
CNJ ro
Ln r-. ^O <T> LT)O Oro r-^ loO O enLO m tx)
0~1 CM LO^ I—CO o OJr— C\J CVJ
r-. LT) CT>r— I— COin un
OJ "O -Q -
fO (O o -—-
—
-
.— 00CO ^rn c\j CO
C\J oLO OOLO CO LO
00 LOCM
—
m •rr
n ro u3cr> CM
CM ro no
OO COun CO
»— "X) O"X) LO cn00 CO r--
<x>O »— COLO enCM CM I
—
(-> at —CO Q '
ro LO I—LO CO 00ro ro r-^
LO CM CMino I— ro
CM CM CM
ro "=3- COCM CM CTlCTt cr> CO
CTi CMLO CO
LO 00ro ro ro
ro ro LOO CM CMLO LO LOCM CM CM
CO CJl COO ro 1—LO LO LOCM CM CM
O LD COLO "=3- COcn CO roro ro ro
i— CM LOO O OO O OI— CM LOO O OO O O
.— CM LOo o oo o o— <:3- IT)O O OO O O
.— CM LDO O OO O O.— CM LOO O OO O O
1— CM LOO O OO O O
O O CMO --^
Li_ a:
O O CMI— OLt_ Cxl
O E roO O (Nl.— O^
O E roO O CM.— O '-^Ll_ CXl
O E OO O ro.— O —
•
Ll_ OC
O E p—O O roO—
O E CMO O ro.— O
20
00 CTt ro oc COCM CM OJ C\J
O CO CO "X)
CO a> r-^ro CM CM CM
OD LD I— O t^J ^ CM U-) O 00
in LO O
in ^ csj o^ CM O
CM mCM in CM
CM r-^ CO ro
cNj tn IX) o•Xi in 00 >— o.— CO ro CM <=}
CM i— CM
in cNi ro
00 CM ^m in i£>o in 00CM CM I— 1
—
00 CM l£)0> CO CO <JiCM ^ o
CO "Xl CM r-I— CM
r— CM CM «=r
in CM — o00 CM in r-x
00 UD in U3CM CM CM CM CM
O Cn CTt
CJ^ CO ^ COCM CM 'ij- CNJ
OJ "O -i^ -QQ. C O r—fO fO O
CO cj> CT^00 CTi CMo C3^ CO
r*- ro cTi
«=J- CM r—CM in CO <X)
*:t cn "X) inCO *X)in U3 "Xi
«;J- 00 CO COen CO oo o cr> t— en
ro CO CM roin ro COCM CM »— CM
+-> (U .—
CM CM COCTl OO r-^ CMCM MD r-^ COro no CM CM
CM O <—>— <T> -rt <Tt
<o >— in roCM ro CM CO
Ln o in CMl£) f— f— <—o o -—
I— CM CM CM
CO O r--ro O VO in "X)K£>ro no ro CO
00 cn <nCM "^a- oix> in lo U3
o I— '^J- ino o o oo o o oO CMo o o oo o o o
O »— CMo o o oo o o oO '— CM roo o o o oo o o o o
<— CM roo o o oo o o o
O E .—o o -^rf— o^ O O "^f^ o^ o o ^
I— o
21
t— -e^ ID ^ O CSJ tX) CO
CTi ro lO
O C\J C\J
C\J O CTi CO
O CTi O "X)
<T3 C 3 <—
CT^ CO I— CT>CO CO on "^tf-
CO C\J (NJ C\J
C\J ^T) r— LOCO O <— CNJCO o oI— C\J f— CNJ
O) "O ^ -O -
Q. C O r—<tJ J -— -
—O CO I— r—CO ^ r-- oCO CO O
m tx)o o C\Jc\j CNJ CO f^J
o U3 CO
ro ro rn CNJ
+-> dj .
—
CNJ Ln CNJ1— LD Ln oCO O 1— COCNJ CNJ C\J CNJ
LD Cr^ CNJ CTi
no CNJ CNI <x><=r LD o~i "^rm CO CNJ ro
F— CNJ CNJ "=J-o o o oo o o oI— CNJ LOo o o oo o o o
o e COO O^ O '
—
22
A detailed breakdown of the inventory weight data is given in Table 6. Thecontribution to the total inventory weight is given for: the furniture andequipment (obtained from the transfer functions); the weight of paper andbooks (also obtained from transfer functions); and the weight of miscellaneousitems which were estimated by the surveyors. The standard deviation for thetotal inventory weight obtained by combining the standard deviations associatedwith the transfer functions for each item of furniture and equipment (5) is
also given.
The estimated weights for the various surveyors in a given room vary con-siderably. In some cases the differences were greater than 100 percent.This is to be expected since the surveyors were not given any special trainingin estimating weights. The contribution of these estimated weights to thetotal weight in the room, however, is very small; in most cases, five percentor less. Extensive training of the surveyors in estimating item weightswould, therefore, not significantly improve the accuracy of the survey technique.
The weight of paper and books in these offices contributed substantially to
the total weight. This contribution ranged from approximately twenty percentto as high as sixty-eight percent. Since it was necessary to select averagesizes for a given pile of paper or books and the height of disorganized pilesor stacks had to be estimated, the surveyors obtained different weights. As
noted previously, estimation errors of this type also occur in surveys usingdirect weighing unless the furniture items and contents are weighed separately.
Differences also occurred in the various surveyor weights from the transferfunctions. Although the item groups used in the transfer functions are notextremely sensitive to the measured dimensions of the item, differences did
occur. For example, in Room 527, Surveyor 002 obtained slightly differentvalues of weight from the transfer functions for the two times he surveyedthe room. In addition, errors occurred in correctly identifying a particular
furniture item or in recording the data and account for the variation among
surveyors
.
These results are understandable and do not indicate any serious difficulties
with the inventory survey technique. Referring to Table 5, the percent
difference between the inventory weights and measured weights is reasonable
in most cases. For three of the rooms (Rooms 305, 423, 526), however, the
percent difference was large. A detailed review of these rooms indicated
that they were similar to the other rooms surveyed with respect to the type
of contents. It was also not possible to attribute these differences to the
survey procedure (time of day, day of the week, etc.). Studies of the data
indicated that the differences were due to surveyor error. Data for Room 423
in Table 7 illustrate this. Note that the total inventory weight for each
surveyor consists of the sum of the item weights, the content weight, and the
weight of the miscellaneous items in Table 7. In some cases measurement errors
occurred, in others errors in identification of furniture items occurred or
data were not recorded.
In order to minimize the chances of including erroneous survey data in the
results, data from the twenty-three buildings were checked prior to analysis.Obviously, detailed checking similar to that discussed was not feasible. Certainlogic type checks were made, however, during the data processing and some datadiscarded.
23
T3 -QO <C
24
C QJ OO CX OI- >, OJ o u
-M tA OCOS
O -CI— <a:
25
Variability between surveyors and errors of the type noted are to beexpected in a survey of this type. Referring to Table 5 and comparing thepercent difference between the measured weight for each room with the meanvalue of the inventory weight obtained by the various surveyors for thatroom column (1) versus column (3) , the average of the absolute values ofthe percent difference is seven percent. The same comparison excluding thethree rooms with obvious data errors gives two percent. Although thesedifferences are small, it is of interest to investigate the significanceof the errors, and in particular their effect on live load variability.
The live load data obtained for these 14 rooms were analyzed to evaluate:(a) surveyor errors and biases, if any, and (b) any evidence of systematicerrors in the inventory procedure. The analysis has four sections:
(1) preliminary analysis of surveyor bias, (2) estimate of variance ofinventory weight, (3) evaluation of systematic errors, and (4) uncertaintiesfor live load expressed in pounds per square foot.
(?) Poii,lbl& SuAv&yon. B^oa o^l Room-by-SuAv^yofi JntzAaction
The intercomparison of inventory results by different surveyors was donetaking into account the fact that not all surveyors surveyed each room.
The inventory weights were displayed in an array by room and surveyor(Table 8). To evaluate any systematic differences between surveyors (adjustedfor differences between rooms), a weighted two-way analysis of variance wasperformed. Numerican values presented herein were obtained from the OMNITABcomputer program. The results are summarized in Table 9. The differencesamong rooms are, as expected, statistically significant as indicated by thef ratio in Table 9. The differences among surveyors are not significant.
On the basis of an analysis of variance, "computed values" are obtained forcomparison with the observed data. They are computed from the estimatedaverage room weight (grand mean in Table 9) plus the appropriate row (room)and column (surveyor) adjustments given in the lower part of Table 9. Thedifferences between observed and computed values, the residuals, are an aid
to interpreting the results. "Standardized residuals" are residuals dividedby their respective standard deviations.
The standardized residuals shown in Table 10 were examined for any evidenceof room-by-surveyor interaction, i.e. to detect effects of any room-plus-surveyor combinations. No such evidence could be seen. Two of the residualsof largest magnitude (exceeding two times their estimated standard deviations)were associated with surveyor number 4 (column 5 in Table 10). Repeating the
analysis with surveyor number 4 omitted reduced the residual standard deviationfrom 233 lbs. to 217 lbs., but the results are qualitatively the same. Surveyornumber 4 was not excluded from later analyses.
Large residuals in Table 10 also seem to be associated with Room 419 and 422
(rows 8 and 9). Comparison of the inventory forms prepared by different
surveyors for these two rooms may help to identify some of the reasons for
discrepancies between surveyors.
26
o o o O LO O o o o o o o o CTt
OOCM 1^
CQ CM OOO
Ln1
—
OvJ CO CM O 00 CO , o O o o o CM00 1
—
CTl CO 00 CM CMLT) OO 00 Ln OO CO CTlCO C\J OO OO CM CMo
o o o CTl o o o 00 , CM o00
LD en UD o oCO OO ,
1
—
OOOB OO CM OO CM OO CM
OO o o o o o o o o O O , CTl o oIT)
OO
ID o OO o LO OO CTl OO CTlCO 1^ CM C\J OO >^ to o CM
OO OO LD CO OO o r~- uo UOCQ ,
—
CM ,
—
CM CM OO CM CM oo CM OOO
OO uo OO OO CO o CM o O O CO CM UOLD CM O o uo OO CTl O CM OO
OO ro o (J\ uo UO uo cn <X) o O OOCQ CNJ OO CM CM OO OO OO CM CM COO
O o o o o O o o CM CM LD CO o O oCTl r-~ OO
OO CM toCQ OO CM r— OOO
o^=3- 00 CTl LT) OO CTl CM OO OO
E CM CO OO O CM CM CM CM CM CM OOo <XI CM CM Osl OO OO OO UO UO UO IT)
oq;
os:
oa.lA<uS-S-oo
oS-
1^
27
TABLE 9 SUMMARY OF WEIGHTED TWO-WAY ANALYSIS OF
VARIANCE FOR INVENTORY WEIGHTS
Analysis of Variance for Two-Way 14 x 7 Table
Effect Source D.F. Sum of Squares Mean Squares F Ratio F. Prob.
Between Rows 13 28835119. 2218086.1 40.936 .000Rows Between Cols 6 1123546.2 187257.71(Rooms) Residuals 29 1571353.8 54184.613
Total 48 31530023.
Between Rows 13 29704043. 2284926.3Col umn Between Cols 6 254623.35 42437.225 .783 .590
(Surveyors
)
Residuals 29 1571353.8 54184.613Total 48 31530023.
A Weighted Least Squares Analysis Using
49 Non-Zero Weights and 49 Zero Weights in Column 1
Coefficient Estimate Stc . Dev.
Grand Mean 2657. 5793 46. 330293
Row 1 -1130. 2603 131
.
26906Row 2 -453 58364 131. 26906Row 3 -721 59364 131. 26906
Row 4 1070 3522 132. 85232
Row 5 -123 20998 143. 27476
Row 6 -114 92697 131
.
26906Row 7 1091 4064 131. 26906
Row 8 501 38036 118. 29704
Row 9 289 64425 118. 13360Row 10 -669 10575 118. 13361
Row 11 1130 9404 111. 55496
Row 12 -1072 6907 122. 87425
Row 13 -465 94654 116. 27035
Row 14 667 60397 121. 96944
Column 1 -144 04410 119. 51660
Col umn 2 63 349267 70. 078650Column 3 -32 680910 73. 605892Column 4 28 295895 163. 82179
Col umn 5 61 481534 92. 964220Column 6 -93 625355 94. 174560
Col umn 7 117 22367 173. 04572
Residual 232 77589
28
29
The analyses summarized in Tables 8 through 10 were repeated for the twoinventory subtotals - estimated weight and weight of paper and books - andfor the percent difference between inventory and measured weights (column 6
in Table 5). The tables are not included here since examination of theresults revealed nothing more than has been discussed for the case of inven-tory weights.
On the basis of these two-way analyses of variance, it appears to be satis-factory to proceed to further analyses in which the identities of the surveyorsare ignored. That is, the three or more surveyors who did each room aretreated as if they were a random sample of the set of surveyors. Differencesamong surveyors are interpreted as the result of a general tendency to makesome errors, since there was no evidence that any surveyor erred consistentlyin such a way as to over- or underestimate the inventory weight.
(2) E^tmatt ofi VoAAJxnct Inv&.ntoA.y W^ght
Variability from surveyor to surveyor in the results of the inventory procedureoccurs because surveyors do not exactly agree on "estimated weights" and on
descriptions and dimensional measurements recorded for furniture, equipment,and paper and books. For a given room, with fixed contents, this kind ofvariability will be called "surveyor error." The variance due to surveyor error
is estimated from the results of repeated surveying [Section (2.2)].
An additional source of variability in the results of the inventory procedureis the difference between actual weights and weights calculated from the
"transfer functions." The pilot survey provides very little direct data for
estimating this component of variance, since the sample of rooms is small and
most of the furniture is standard Government-issue.
For a fixed room, the differences between actual and inventory weights of
furniture items are fixed, of course (except for "surveyor error"); they
acquire the character of random variation only when a set of rooms is sampled
from a larger population. The inventory procedure does, however, provide a
computed standard deviation based on the standard deviations associated with
the transfer functions [column (2) in Table 6]. This is the best availablemeasure of the contribution of this source of variability to the overall
uncertainty of the inventory procedure [Section (2.3)].
Paper and books make up a substantial fraction of the total live load. A
special analysis of the surveyor-to-surveyor variability was done for this
subtotal of the inventory weight [Section (2.4)].
The results of the studies of variance components are summarized and a combined
estimate of the total uncertainty of the inventory procedure is given in
Section (2.5).
First, in Section (2.1), the general ideas for the evaluation of variance
estimates are discussed.
30
(2.1) Relation of Variability to Room Weight
Variability of inventory weights might be expected to depend to some degreeon the magnitude of the live load in a room. For each of the variance components,three alternative forms of this relationship are compared:
(1) constant variance,
(2) variance proportional to total weight (roughly equivalentto variance proportional to number of items inventoried),
(3) variance proportional to squared total weight (i.e., standarddeviation proportional to total weight; constant relativestandard deviation).
Let s. denote the standard deviation (square root of variance) for the j-throom,"^and let M. denote an appropriate measure of the total weight in the
room. According to the three possibilities listed above, oneof the following quantities would appear to be reasonably constant fromroom to room:
(1) Sj
(2) / V"^
(3) s. /Mj
Since the number of surveyors is small for each room (3, 4, or 5), one wouldexpect to see a lot of sampling variability between rooms. (Sampling varia-
bility is more pronounced for standard deviations than it is for averages.)
To assess this sampling variability, the values of each of the three measuresof variability were tested for homogeneity.
Two tests for homogeneity of variance were used, Bartlett's and Cochran's.
Notation
t- = one of the three quantities above, for j-th room3
n. = number of surveyors, for j-th roomJ
N = znj
k = number of rooms
Sp = z(n. - 1) t^ / (N - k)
Bartlett: M = (N - k)^n Sp - lin. - l)£n t^.
2 2Cochran: C = largest t^ / Etj
j
31
The test of significance for Bartlett's M is described in Reference 9
(page 309). Cochran's test (Reference 9, page 310) can only be used whenall the nj are equal. This test was done for two subsets of the rooms -
7 rooms for which n^ = 3 and 6 rooms for which n^ = 4.
The critical values for the tests of homogeneity, which must be exceeded by
the test statistics for rejection of the null hypothesis of homogeneity atthe specified probability levels are:
Probability .05 . .01
Cochran's C (7 samples of 3) .5612 .6644
(6 samples of 4) .5321 .6258
Bartlett's M 25.6 31 .5
To aid in interpretation of the formal tests of significance, the variance2
measures t. were also shown on probability plots. If the values of t. are
different only because of sampling variability, then the values ordered fromsmallest to largest can be compared to percent-points of the chi-squareddistribution. The probability plots were done in pairs, first for the seven
rooms with n. = 3, and second for the six rooms with n. = 4 (actually forJ J
seven rooms, since the room with "^j" 5 was included in this set for plotting).
In order that horizontal and vertical scales be the same in all the probability2 2
plots, the values of tj were divided by the appropriate pooled measure Sp, and
the percent points of the chi-squared distribution were divided by the value
of degrees-of-freedom v = (n .-
1 ) , 2, or 3. The plotting positions for the2 J 2
ordered values of t^ were the percent points of x corresponding to proba-
bilities j / (N + 1), i.e. Vg, . . . ,'^/g .
2Percent Points of x /
V
i ^ ^1 .13 .23
2 .29 .40
3 .47 .59
4 .69 .79
5 .99 1.04
6 1.51 1.38
7 2.13 1.95
32
Note that the tests for homogeneity of variance, and the probability plotsare approximate to the extent that the data are not exactly normallydistributed.
(2.2) Variability Due to Surveyor Error
For each room, the sample variance calculated from the several inventoryweight values is an estimate of the variance due to surveyor error. Thecalculated standard deviations are shown in Table 11. The measured weightfor each room is used as the measure of the total weight in the j-th
room. Table 11 also shows the standard deviation s. divided by VM . andJ J
Sj / (the latter multiplied by 100 to be read as a percent.)
To facilitate examination of the effect of M^, the rooms are listed in
Table 11 in order of increasing values of M^. Although there is a great
deal of sampling variability, the larger values of s^ do appear to be asso-
ciated with the larger values of M^. The coefficient of variation appears
to be the most appropriate measure of variability for surveyor error. Theresults of the tests for homogeneity of variance are not perfectly clear-cutin Table 11. The Bartlett statistic and one of the Cochran statistics havetheir smallest values for the coefficient of variation. The tests of signif-icance indicate that the surveyor error variability may not be the same for
all rooms. (All values of M and one value of C are "significant" at the .01
probability level.) This might be interpreted to mean that surveyor errorsare occasionally larger than those predicted by normal distribution theory.
The pooled estimate, coefficient of variation for surveyor error of
8.33 percent, is valid without depending on normal distribution theory. Butnote that "two-sigma" types of multiples of this estimate must be interpretedwith caution.
(2.3) Variability Due to Transfer Functions
For each surveyor, the inventory procedure produced a standard deviation[column (2) in Table 6] computed from the standard deviations associated with
the transfer functions. The average of the squares of these standard devia-
tions is an estimate of the variance due to use of transfer functions for
each room. The corresponding standard deviations are given in Table 12.
Each of the three variability measures s., s. / and s. / M. gives values
well within the range expected due to sampling variability. (No "significant"
test statistics.) The values of the test statistics seem to suggest that the
transfer function variance is constant instead of depending on the total
weight of room contents; this is a surprising result. Because other varia-
bilities seem to be best described by the coefficient of variation, and since
the assumption of constant coefficient of variation is not rejected by the
significance tests, the coefficient of variation is suggested as a measureof transfer function variability.
33
TABLE 11 STANDARD DEVIATIONS FOR SURVEYOR ERROR
KUUill
No.
Measured
M.J
Standarducv . ^ 1 u y
S .
J
s .
J
v/TT^ J
Coeff
.
co -
_±MJ
of Var.
X 100
JH 1 51 H 9Rc o
1 JUO L. JO U . 1 J 7ft/ o
4 £ O i HO ^ 79 q ^R0 J
CO 1 1 y JO 1 0 77/ /
OU J L uoo / u 1 JJ 'X0 ou
91£ 1 HO 1 9n 9 RQ J RQo^
\>C t 1 9^ 9 fifi co fi70 /
0 1 J 1 u . O 1finou
A9n 7 fi?/ . DO 1 0 OD
419 3129 407 7.28 13 01
634 3354 281 4.85 8 38
523 3597 67
239 3774 147 2.39 3 90
321 3840 299 4.83 7 79
: Pooled (v-2)
Pooled (v=3)
164
277
3.295.13
7
9
25
74
Pooled (all) 225 4.23 8 33
Cochran (n=3)
Cochran {n=4)
.4770
.38234953,3686
Bartlett 39.2929 34.1754
Note: Rooms are listed in order of increasing measured weight
.6762
.3374
32.4512
34
TABLE 12 STANDARD DEVIATIONS FOR TRANSFER FUNCTION ERROR
RoomNo.
MeasuredWt. (lb)
M.J
StandardDev. (lb)
s
.
J
s .
J
^ J
Coeff. of Var.
^ X 100
"j
526 1271 86 2.41 6.77
224 1508 123 3.17 8.16
423 1583 101 2.54 6.38
231 1953 73 1.65 3.74
305 2083 106 2.32 5.09
228 2148 134 2.89 6.24
527 2203 77 1.64 3.50
313 2645 100 1.94 3.78
422 3031 103 1.87 3.40
419 3129 101 1.81 3.23
634 3354 78 1.35 2.33
523 3597 no 1 .83 3.06
239 3774 114 1.86 3.02
321 3840 96 1 .55 2.50
P
P
ooled (v=2)
ooled (v=3)
108no
2.271 . yo
5.004 . DO
Pooled (all) 100 2.08 4.61
Cochran (n=3)
Cochran (n=4)
.2193
.2104
.2776
.2739
.3802
.3631
Bartlett 1.9077 3.9557 10.6749
35
The pooled estimate, coefficient of variation for transfer function error,is 4.61 percent.
(2.4) Surveyor and Transfer Function Error, Paper and Books
For the weight of paper and books, differences between surveyors led to thestandard deviations shown in Table 13. In this table, rooms are listed in
order of increasing value of the average inventory weight subtotal forpaper and books.
In this case, the tests for homogeneity of variance reject the assumptionthat the variance is constant. The coefficient of variation is againsuggested as the appropriate measure of variability.
The pooled estimate, coefficient of variation for surveyor error (paper andbooks only), is 13.90 percent.
This separate analysis of the surveyor error for paper and books has beendone because paper and books are a substantial fraction of total weight.Also, the standard deviations shown in Table 13 are substantial parts ofthe corresponding standard deviations in Table 11. In fact, for 4 of the14 rooms, the standard deviation for paper and books is larger than thestandard deviation for surveyor error for the total inventory weight. Thatis, the numbers in column (4) of Table 6 are more variable than those in
column (1). See, for example, room 228. The errors in paper and bookrecording were offset by opposite errors in other parts of the inventoryprocedure for these rooms.
The transfer functions (Reference 5, Table 13) are accompanied by standarddeviations: the indicated values are roughly equal to 10 percent of theweight (lb per inch) established for each size class. The computed standarddeviation for a pile of paper or books is defined in Section 4.2.2.2.2 of
Reference 6. The computation allows for errors up to one-half unit in thelast figure recorded by the surveyor for the height of the pile and makesa similar allowance for round-off of the estimated compaction factors. Theeffect of the weight standard deviation is assumed to be proportional to the
height of the pile. The transfer function error can be thought of as
reflecting (i) variations in the weight of paper and binding materials and(ii) deviations from the exact volume imputed to the recorded quantity(inches) of paper in a particular size class. Surveyor error includes (iii)
dimensional measurement errors leading to different size classes as well as
to variability in the number of inches within a size class and (iv) errorsdue to the approximation embodied in the compaction factor. The transferfunction and its associated standard deviation were based in part on experi-mental weighings. Thus, the question arises whether any surveyor error is
being "double-counted." Considering the four sources of errors describedabove, it seems the overlap is very small if there is any at all.
The piles of paper and books were not weighed separately so bias associatedwith this part of the inventory procedure cannot be assessed separately.
36
TABLE 13 STANDARD DEVIATIONS FOR SURVEYOR ERROR(PAPER AND BOOKS ONLY)
RoomNo.
MeasuredWt. (lb)
M .
J
StandardDev. (lb)
s .
J
t—
v/s-
Coeff. of Var.
X 100
M.J
526 233 36 2.36 15.45
224 313 69 3.90 22.04
231 406 28 1 .39 6.90
305 436 88 4.21 20.18
228 649 150 5.89 23.11
423 649 43 1 .69 6.63
313 836 40 1 .38 4.78
419 867 112 3.80 12.92
527 875 103 3.48 11 .77
523 1029 72 2.24 7.00
634 1133 159 4.72 14.03
239 1331 60 1 .64 4.51
422 1476 254 6.61 17.21
321 2352 366 7.55 15.56
Pooled (v=2)
Pooled (v=3)
1 58
139
4. 33
4.101 5.8613.42
Pooled (all) 141 4.03 13.90
Cochran (n=3)
Cochran (n=4)
.7657
. 5557
.4343
.4327
.3034
.2739
Bartlett 35.4721 18.5182 15.1760
Note: Rooms are listed in order of increasing average inventory weightsubtotal for paper and books.
37
(2.5) Summary
The variance for the inventory weight of a room, including both surveyorvariability and transfer function errors, is estimated by the sum of thetwo variance components. The room-by-room estimates are shown in Table 14
as standard deviations (square root of the sum of squares of correspondingstandard deviations in Tables 11 and 12).
The coefficient of variation is, as expected from the previous results,found to be the appropriate measure of variability. See Figures 4 to 9
in addition to the test statistics in Table 14.
The pooled estimate can be calculated in two ways. First, there is thevalue 9.52 percent shown in Table 14. Alternatively, one can calculate thesquare root of the sum of squares of the pooled estimates from Tables 11
and 12; this value is 9.52 percent also.
Rounding off, we find the standard deviation of the inventory procedure is
10 percent of the inventory weight. This is a measure of the variance aboutthe average for surveyors and the assigned values in the transfer functions;it does not include the effect of biases in either of them, discussed in
the next section. Conventional probability statements associated with multiplof the estimated standard deviation should be interpreted with caution sincethere is evidence (Figures 4 through 9) that the inventory weight data arenot normally distributed. (That is, the measurement errors in repeatedinventorying of the same room may not be normally distributed.)
(3) EvaJLuuoution oi Syi>tmcLtia Efinon. In lnvQyvton.y VfiocddoMO,
There are two possible sources of systematic error in the inventory procedure:the transfer functions and surveyor bias. The two kinds cannot be separatedfrom each other in the data available here.
It was found in Section (1) above that none of the surveyors seemed to be
biased with respect to the others in the group. The remaining possibilityis that surveyors as a group are biased, i.e. that the average of repeatedinventorying of a fixed room by many surveyors would be different from the
measured weight for reasons other than transfer function error (general
tendency to under- or overestimate dimensions, for example, or tendency to
omit items).
The inventory data for any one of the 14 rooms in this survey are "correlated"
with respect to estimating systematic error since the same transfer functionerror is present for each surveyor. We have, however, 14 room-averages of
inventory weights. These are shown in Table 15 along with percent differences
from measured weight. Notice that half the differences are positive and half
negative.
Notice also that the large percent differences are not associated with rooms
in which there were large differences among surveyors. In fact, two of
the three largest surveyor-error variance estimates were obtained in rooms224 and 419 which have the smallest (in magnitude) percent differences.(Compare with Table 11.)
38
TABLE 14 STANDARD DEVIATIONS FOR INVENTORY TECHNIQUE(SURVEYOR AND TRANSFER FUNCTION ERRORS COMBINED)
RoomNO
.
MeasuredWt. (lb)
Mn .
J
StandardDev. (lb)
s
.
JVMj
Coeff. of Var.
s .
—^ X 1 00
M.J
526 1271 101 2.83 7.95
224 1508 268 6.90 17.77
423 1583 179 4.50 11.31
231 1953 74 1.67 3.79
305 2083 127 2.78 6.10
228 2148 180 3.88 8.38
527 2203 147 3.13 6.67
313 2645 101 1.96 3.82
422 3031 433 7.86 14.29
419 3129 420 7.51 13.42
634 3354 291 5.02 8.68
523 3597 172 2.87 4.78
239 3774 186 3.03 4.93
321 3840 314 5.07 8.18
Pooled (v=2)
Pooled (v=3)
196
2924.005.50
8.81
10.76
Pooled (all) 247 4.72 9.52
Cochran (n=3)
Cochran (n=4)
.3662
.3659
.4254
.3407
.5813
.2936
Bartlett 17.9052 . 14.0681 14.1362
39
— c c
I I I I I 1 I I I I I I I I I I I I + I
40
3 ZO —o o'O a.
iiiii-fiiiiiiiii + iiiiiiiii + iiiiiiiii
41
lilt
C CL
o zc —3 OO Q_
I I I I I I I I I I I I
42
I I I I I I + I I I I t lll-flllllllll + lllllllll + lllllllllx^LJ
O U1
+ »-
o zc —o o
><Ql— «tZULjyi
43
I I I I I
o —o o-0 X
I I I I I I I 4- I I + I I 10 1 I I I I I I I I I I I I I I I I I I I
44
14 11 II I I I I
I I I I I I I I I
45
TABLE 15 MEASURED WEIGHTS AND AVERAGE INVENTORY WEIGHTS
RoomNo.
Mpasurpd1 1 v.. U .J 1 \—
Wt. (lb)
(1)
AverageI nvpntorvwt. (lb)
(2)
Percent Difference(1) - (2)
t]) ' X 100
(3)
224 1 508 1506 0.13
228 2148 2183 -1.63
231 1953 1915 1.95
239 3774 3738 0,95
305 2083 2584 -24.04
313 2645 2522 4.65
321 3840 3728 2.92
419 3129 3131 -0.06
422 3031 2934 3.19
423 1583 1975 -24.79
523 3597 3784 -5.19
526 1271 1615 -27.06
527 2203 2207 -0.18
634 3354 3339 0.45
46
Using the results of Section (2), a percent difference in Table 15 shouldhave variance
(Transfer Function Variance) + (Surveyor Error Variance)
n
where n is the number of surveyors who inventoried the room. For the sevenrooms on the third and fourth floors, n=3. For the seven rooms on thefifth, sixth, and seventh floors, n=4 (except room 523 with n=5). Using thepooled values from Tables 11 and 12 gives:
2
(4.61)2 + (8-33) . (6.66)2 ,
3
2
(4.61)2 + (8.33) ^ (6.21)2 _
4
All but three of the percent differences in Table 15 are smaller than thesevalues. The three values of about -25% are roughly three times theirstandard deviations. In the following discussion, data for all 14 roomsare analyzed simultaneously, ignoring (as a second-order effect) thetheoretical difference in the standard deviations. The standard deviationfor the percent difference is taken to be 6.5.
The average of the percent differences is -4.91 and its standard error is
6.5 / /14 = 1.74. If the measurement errors in the inventory data were nor-mally distributed, the average should lie within + 2.160 times its estimatedstandard error for a confidence level 0.95 or + 3.012 for a confidence level
of 0.99. These confidence intervals (based on Student's t) for the averagepercent difference include zero at the 99% level, but not at the 95% level.
The analysis based on normal distribution theory can be challenged. Assumingapproximately constant coefficient of variation, the percent differencesshould be distributed about some average value (the systematic error, not
necessarily zero), with standard deviation 6.5. The computed standard devia-
tion for column (3) of Table 15, however, is 11.3. Considering the small
sample sizes, the two values are not inconsistent. But, it must be noted
that the percent differences tended to be more variable than was predictedfrom the analysis of inventory data.
A distribution-free analysis has also been done. (This reduces the effect
on the results of the three 25% deviations.) The hypothesis that the systematic
error is zero cannot be rejected at the 95% level by the Wilcoxan signed-ranks
test (Reference 10, Chapter 5.1). A 95% confidence interval, associated with
the test, is:
-12.2% < bias <_ +1.5%
A "robust" estimate of the bias is -0.8 percent.
47
In conclusion, the data suggest the possibility of systematic error butthe error, if any, appears to be small with respect to the variance of theinventory procedure. The estimated 10 percent coefficient of variation forthe survey procedure overwhelms a possible one to five percent bias. Thesystematic error, if any, leads to overestimation of live loads.
(4) ^AzaMj/Lmznt UncoAZalvvty (^OK. Livd load
Up to now, this analysis has been conducted in terms of total weights in
pounds. An analysis performed in live load units (pounds per square foot)would differ only very slightly since 12 of the 14 rooms had areas of 177
to 180 square feet. (Exceptions: Room 422, 163 ft^; Room 526, 265 ft^.)Coefficients of variation would not change at all since the conversion fromlbs. to psf would affect both numerator and denominator of the ratio.
The principal result from this analysis is that the variability of live loaddue to the survey procedure, including transfer functions and surveyor errors,is estimated to be 10 percent of the measured load. The systematic error, if
any, is essentially negligible in comparison with the statistical varia-bility; there may be a very slight tendency for the inventory weight to over-estimate the actual weight.
The "measurement error" associated with the survey problem is, in turn,negligible with respect to the variability of live loads from room to roomin office buildings. For 149 rooms in the NBS building, the average live
load was 15.7 psf, with a standard deviation of 8.2 psf. The coefficientof variation exceeds 50 percent.
Since the total coefficient of variation, including the variability of liveloads and the "measurement error," is estimated by the sum of the two
components, i.e.:
(50)^ + (10)^ = (51)^
it is evident that where the room-to-room variability is about 50 percent,
the coefficient of variation for loads determined by the inventory procedurewith 10 percent variability is negligibly larger.*
Based on the preceding analysis, it was concluded that it was not necessary
to account for "measurement errors" associated with the inventory procedure
in reducing the survey data.
*For the measured weights of the 14 rooms considered in the report, the
average live load was 14.3 psf with standard deviation of 5.2 psf, andcoefficient of variation of 36 percent. A 10 percent measurement errorwould increase this variation to 38 percent. The average live load basedon average inventory weights [column (2) in Table 15] is 14.7 psf with a
standard deviation of 4.8 psf (c.v. 33%). This is not quite comparablesince the averaging of several surveyors would tend to reduce variability.
48
3.3 Characteristics of Survey Sample
Data on room use and occupancy characteristics are presented in Tables 16
and 17. The classification of firms used in Table 17 was in accordancewith standard classifications developed to promote uniformity and compara-bility in the presentation of statistical data (11).
The number of each type of room in the buildings and the number selectedfor survey are given in Table 16. General and clerical offices wereobviously the most prevalent followed in order by storage areas, conferencerooms, lobbies, file rooms, and libraries. There were a number of vacantrooms in most buildings. The number of rooms given in parentheses (exceptfor Buildings 14, 24, and 27) only include the rooms randomly selected on
the basis of firm type, room use and room area (5). The additional tenpercent sample of adjacent rooms selected to obtain loads for areas largerthan an individual office (5) are not included. For Buildings 14 and 27,
all the rooms where access was possible were surveyed and these are
indicated in parentheses. For a few cases, access could not be obtainedfor security reasons, etc. In the pilot survey of the NBS AdministrationBuilding the twenty-five percent sampling rate was also not used and all
the rooms with the exception of three floors were surveyed.
A higher sampling rate was used for Buildings 14, 24, and 27 in order to obtaindata to check the mathematical load models developed from the survey data
(Section 3.8). Comparing loads predicted for the entire building using
these models with the surveyed loads permitted an evaluation of their accu-
racy as discussed in Section 3.9.
A total of 2,433 rooms was originally selected in the twenty-three buildings.
The breakdown of this total according to the selection procedure used was
as follows:
Total No.
Included in
Table 16
Random Selection (excluding Bldgs. 14, 24, & 27). . . 1,376
Random Selection (Bldgs. 14, 24, & 27) 261
Extra Rooms (Bldgs. 14, 24, & 27) 616
Adjacent Rooms (Bldgs. 14, 24, & 27) 2^Adjacent Rooms (excluding Bldgs. 14, 24, & 27). . . . 152
TOTAL 2,433
The number of rooms actually used in the data analysis is given in Table 18.
As indicated previously, the data for 8.5 percent of the rooms surveyed
were discarded due to errors. The numbers for each selection procedure are
listed separately in Table 18. Of the 2,226 used, 1,354 were randomlyselected, 245 were adjacent rooms, and 627 were extra rooms surveyed in
Buildings 14, 24, and 27. The percentage of adjacent rooms selected by the
surveyors[y^^f^
^ 100 ^ 18% was higher than originally intended (5).
The surveyor errors discussed in Section 2.4, which resulted in discarding
49
a3U
oo
JO
jQ
cntos_o4->
o
O
S-<DcQJCD
O) •
-a o
LO CMCXI
CO00
CO
LO I
CM I ID
CO I CMCO
CO ^
CO
CO
CO
EooS-
(->
o(0••-)
-ara
4-OOJ>1/1
3OXQJ
o 1/1
(LI E-i-J oCJ o(U S-
fOto S-
!->
(/) Xe cuoo T3S- C
nsM-O +->
CS- OJcu o
to
E ••-)
50
4-Oi-
O -r-
a. =t
I
s-O CQ. Oc +->
ro fOS- +->
CVI r
IX)CNJ
o <
en
3 s-c: 3(13 +->
o3S- c+-> o1/1 -I-
c: +->
oC_3
s_ +->
cru-et 3
T3 O CO O I—CNJ C\J CM < CNJ
51
00
oo
oo>-_l
00o
UJI—t_>
q:
oo
<X1 CM '
—
o ro CTi LO C\J C\J o CO CM LDn3-!-> C\J ro
To
>i
o O '
—
o o o O o o o o o o O
QJ
ra o o o o oo , OO O , o , o 00 o 1
Q+->
OO
0) O o o o o O o o o o o o O o•1-
Ll_
0)C/l
om4-
CM O o — o O o <— o oo od;
>^-QJ3 o CM o o o o OO
O1
rao
CVJ 1
—
1
—
o CM o 00 o o o I
—
O o CM Os_QJ
C_)
13S- 1.0 o CO LO CO CM 00 o OO
<u'~~ CO CM
c +-> +J +-> •4-> -!-> +-> +->
o c•1— LO QJ QJ QJ Q) 0) Q) E QJ E QJ-(-> -1- O o o u o o o CJ o <J o o O O O OO (/I T3 T3 fO n3 x> n3 ra T3 (T3 T3 ra -D n3
QJ 13 c ••"^ •—J C ''~) •<-^ C "-Jr— CQ ro -D o o (T3 T3 ra T3 -a ra 13Ol q: <: q: eC q; <C Q£ Od <C <. d; eCOO
1
—
1
—
o CO '
—
00 LO o cn o CO LO LO CMc/l CO 1
—
CO CTi CM o(T3 fO EC\J CSJ Ln o CO C\J CO CO OO O CTl
+-> OlU- O +->
O t- O O OO CO cri
1— <C CM
Cn .
-o O CM ro 00 O1— SCQ
52
Total
O-i 1— 1
—
00 ^ OvJ CTI IT)
00 r—O^J
o Ln uocn >—
COCO LnCM
(J\ CM
Li
brary o O O o o O O r— 1— o o o Ln o o o
Storage
.— o OO O r--. o CO r- 00oo
CVI o 00 CM CMCNJ
CM O
Fileo o 1— ou o o oo o o 1— o Ln o o r— O
Room
Us
Conf.
>— o O O oo o .— 1— CM I— 1— o 1— Lnoo
r- O
Lobbyo o oo O 1— (XI r— cn ^ o oo 1
—
1— LDCM
O
Clerical
CXJ o X) I— o 1
—
O r\ Lnoo
00 oooo
o
General
^ <— 00 oo O OvJ
ooLn un i\
r— OOoo 00 CM Ln
UD ooO CM
be
lection
BasisRandom
Adjacent
Random
Adjacent
Random
Adjacent
Random
Adjacent
ExtraRandom
Adjacent
Random
Adjacent
Random
Adjacent
Random
Adjacent
TotalAreaof Rooms
1,992
2005,052
1,537
17,9572,580
20,5122,408
55,6299,022
1,276
19,0642,634
53,5158,641 3,350
206
Bldg.No.
oo 00 CTi oCM
53
o
tn
oo>-_)
<:
00
00
DC
O
<:
oo
CO
Total
un ix> CO IX)a~i 0CM ,
—
CO 0 0 CMro t—
1— roCM
00 CM 00 ro 0.— .— 01— ro
Library
!
0 0 0 0 0 i— 0 cn 0 0 0 0 0 0 CM
Storage
CO 0 un 1— ro 0 0 0 CM cn 0 1— 0 0 r— CM1— CNJ
CD
File
r— 0 1— 0 0 1— 0 CM r- 0 CnJ .
—
,— r- l£3
Room
Usi
Conf.
CM 00CM
r— 0 r-- 1
—
Lobby
0 0 CO 1— 0 000 1— 0 0 LD 0 cn
Clerical
ro 0 0 CMCM
CM 0 CTl 0 1X>CM
CD 0 CM 0 Ln ro CDro LO
General
j1X> CO 0 Ln
CM O)CM
.— 0 Ln 0 ODCM
CTl CM 0 COCD CO
Selection
Basi
s
Random
Adjacent
Random
Adjacent
Random
Adjacent
Random
Adjacent
ExtraRandom
Adjacent
Random
Adjacent
Random
Adjacent
Extra
TotalArea of Rooms (ft^)
;
25,479
;
1,805
83,306
!
20,214
^0 0CTl
ro
8,773
'0!,
29,728
14,975
8958,014
1
1,130
127,159
3,83873,012
Bldg.No. CM
CMCM
roCM CM
unCNJ
CDCM CM
CDCMCM
h-o
CTl
<I—o
54
some of the rooms did not seem to be related to the type of the room(general, clerical, etc.). The relative mix of room use types used in theanalysis, therefore, was not significantly different from that of the originalsurvey sample selected. For example, 941 of the 1,637 randomly selectedrooms in Table 16 or fifty-seven percent were general offices. This changed
to sixty-one percent for the analysis sample in Table 18 [y^|g4 x looj .
The changes for the other types of room use were also small.
In general, only the 1,354 randomly selected rooms, of which 1,044 weregeneral and clerical offices, were used in the analyses in Section 3.4through 3.8. The sample size for some of the room use types was small sincea constant sampling fraction was used (5). For example, only one percent
X lOoJ of the random sample was libraries. The adjacent rooms were
included with these randomly selected rooms in determining the relationshipbetween loads and area in Section 3.6. The extra rooms in Buildings 14, 24,
and 27 were only used in the evaluation of the load models in Section 3.9.
The number of rooms used in each analysis in Section 3.4 through 3.9 is
indicated therein.
The occupancy characteristics for the survey sample given in Table 17 indicate
that a majority of the firms were service, finance, or public administrationtype organizations. For the government buildings (Buildings 21-27), the firms
were primarily public administration.
3.4 Influence of Building Characteristics
Fire load and live load data for all the buildings are presented in Tables19 through 22. Buildings in each Census region are grouped according toheight in Tables 19 and 20, and according to age in Tables 21 and 22. Maximumand minimum values and the mean and standard deviation are given for eachcategory. The following relationships were used for the mean and standarddeviations throughout this report:
The standard deviation is a measure of data dispersion even for non-normal distributions. For those distributions in this report which do
not appear to be normal, an assumption regarding the form of the distribu-tion in addition to the standard deviation and mean are required forestimating fractiles.
The loads are expressed in terms of pounds per square foot (psf) and wereobtained by dividing the total load in each room by the floor area of theroom. The fire load is the total weight of combustibles converted to an
equivalent weight of combustibles with a calorific value of 8000 Btu/lb.No derating factor was applied to the enclosed combustibles such as papersin f il ing cabinets (5)
.
The minimum value for the live load is zero in several cases in Tables 20
and 22. Lobbies with no furniture or empty rooms account for these values.
The corresponding fire loads, however, are not zero because of the interiorfinish for the walls, ceiling, and floor.
The data in Tables 19 and 20 do not indicate any definite relationshipbetween load magnitude and building height. For the northeast region the
mean load increases with height but there is no consistent trend for the
other regions. Tables 21 and 22 seem to indicate a decrease in the meanload with increasing age. The southern region and the oldest building in
the western region, however, do not follow this trend. The mean values do
appear to vary somewhat with geographic location. The difference in samplesize for each region may affect this variation. The three parameters:building height, building age, and geographic location were considered in
developing the load models and their influence is discussed further in
Section 3.8.
1 n
X - - z
n i-1
X.
56
TABLE 19 INFLUENCE OF GEOGRAPHIC LOCATION ANDBUILDING HEIGHT ON FIRE LOAD
CensusRegion
HeightGroup(No. of
Stones)
No . of
Bldgs.
Total Fire Load (psf)
No . Ot
Rooms Max. Min. Mean Std.
Dev
.
1 - 5 2 36 19.2 0.9 5.1 4.2
6 - 10 1 11 17.5 1.4 6.2 4.3
Northeast 11-20 0
> 20 3 362 106.5 0.3 7.9 7.7
All Bldgs. 6 409 106.6 0.3 7.6 7.4
1 - 5 3 41 24.0 0.5 6.2 4. 3
6 - 10 0 -- -- -- — --
North-central
11-20
> 20
1
1
3^
42
39.7
19.8
1.2
1.4
7.4
6.4
8.0
4.1
All Bldgs. 5 117 39.7 0.5 6.6 5.5
1 - 5 2 29 39.9 1.1 8.1 7.9
6 - 10 2 79 45.3 1.6 7.7 6.5
South 11-20 1 37 31 .7 2.6 12.1 6.4
> 20 1 82 30.4 0.4 7.4 5.9
All Bldgs. 6 227 45.3 0.4 8.3 6.6
1 - 5 2 37 33.3 1.0 8.6 7.5
6 - 10 1 60 29.0 1.5 5.5 4.0
West 11-20 2 215 48.5 0.5 5.8 5.9
> 20 1 289 51 .8 0.6 10.1 6.7
All Bldgs. 6 601 51 .8 n.5 8.0 6.6
Governrnent and Private Buildings
(Only those rooms that were randomly selected were used for this table.)
57
TABLE 20 INFLUENCE OF GEOGRAPHIC LOCATION AND
BUILDING HEIGHT ON LIVE LOAD
Census
Keg 1 on
HeightGroup
( Nn nf
Stories
)
No. of
Bl dgs
.
No. ofLive Loa d (psf)
Max. Min. Mean Std.
Dev.
1 - 5 2 36 35.4 0.2 7.2 6.4
6-10 1 11 21 .1 0.4 7.8 6.1
Northeast n - 20 0
> cu30 •JVC. 127.7 0.0 10.6 10.0
All Bldgs. 6 409 127.7 0.0 10.2 9.7
1 - 5 3 41 52.7 0.0 8.1 10.0
6 - 10 0
North-
central
11-20 1
1
34
A 0
37 Q
25. 3
1 fi1 . u
0.
1
Q n-7 . 'J
7.2
o . 1
4.8
All Rldas K 1 1
7
52.7 o.n 8.0 7.8
1 - 5 2 29 38.0 1.8 10.3 9.1
6 - 10 2 79 74.3 0.2 9.1 10.3
South 11-20 1 37 43.0 6.4 16.1 8.3
> 20 1 82 44.6 0.0 9.3 8.0
All Bldgs. 6 227 74.3 0.0 10.5 9.3
1 - 5 2 37 33.4 0.0 12.7 7.7
6 - 10 1 60 35.4 0.0 6.7 6.3
West 11-20 2 215 55.6 0.0 8.0 7.2
> 20 1 289 50.1 0.0 11.5 7.7
All Bldgs. 6 601 55.6 0.0 9.9 7.7
Government and Private Buildings
(Only those rooms that were randomly selected were used for this table.)
58
TABLE 21 INFLUENCE OF GEOGRAPHIC LOCATION ANDBUILDING AGE ON FIRE LOAD
CensusRegion
AgeGroup
( Years
)
No . of
Bldgs.No. ofRooms
Total Fire Load (psf)
Max. Min. Mean Std.
Dev
.
1 - 5 0 -- -- -- — --
6 - 10 1 294 106.6 0.3 8.4 8.1
Northeast 11-20 1 21 17.2 1.1 4.8 3.7
> 20 4 94 35.1 0.9 5.9 4.9
All Bldgs. 6 409 106.6 0.3 7.6 7.4
1 - 5 1 12 14.5 2.3 7.9 3.3
6 - 10 2 52 39.7 1.2 6.0 6.7
North-central
11-20
> 20
2
0
53
--
24.0
--
0.5
—6.8
--
4.6
--
All Bldgs. 5 117 39.7 0.5 6.6 5.5
1 - 5 1 48 27.0 1.6 7.0 4.7
6 - 10 2 29 39.9 1.1 8.1 7.9
South 11-20 1 37 31.7 2.6 12.1 6.4
> 20 2 113 45.3 0.4 7.7 6.7
All Bldgs. 6 227 45.3 0.4 8.3 6.6
1 - 5 1 289 51.8 0.6 10.1 6.7
6 - 10 1 118 44.5 0.5 3.9 4.4
West 11-20 3 175 48.5 1.0 7.2 5.8
> 20 1 19 33.3 3.1 9.5 9.0
All Bldgs. 6 601 51.8 0.5 8.0 6.6
Government and Private Buildings
(Only those rooms that were randomly selected were used for this table.)
59
TABLE 22 INFLUENCE OF GEOGRAPHIC LOCATION ANDBUILDING AGE ON LIVE LOAD
Census
Region
Age
Group(Years)
IN 0 . 0 T
Bldgs.
no. OT
Rooms
Live Load (psf)
Max. Min. Mean Std.
Dev
.
1 - 5 0 -- -- -- -- --
6 - 10 1 294 127.7 0.0 11.4 10.5
Northeast 11-20 1 21 35.4 2.2 8.3 6.9
> 20 4 94 33.9 0.0 7.1 5.8
All Bldgs. 6 409 127.7 0.0 10.2 9.7
1 - 5 1 12 52.7 1.4 11.2 13.8
6 - 10 2 52 37.9 0.0 7.5 7.0
North-central
11-20
> 20
2
0
53
--
44.9
--
0.1
--
7.8
--
6.8
--
All Bldgs. 5 117 52.7 0.0 8.0 7.8
1 - 5 1 48 26.7 1.7 7.6 5.1
6 - 10 2 29 38.0 1.8 10.3 9.1
South n - 20 1 37 43.0 6.4 16.1 8.3
> 20 2 113 74.3 0.0 9.9 10.4
All Bldgs. 6 227 74.3 0.0 10.5 9.3
1 - 5 1 289 50.1 0.0 11.5 7.7
6 - 10 1 118 55.6 0.1 6.7 6.0
West 11-20 3 175 54.7 0.0 8.9 7.6
> 20 1 19 33.4 0.0 13.1 8.7
All Bldgs. 6 601 55.6 0.0 9.9 7.7
Government and Private Buildings
(Only those rooms that were randomly selected were used for this table.)
60
3.5 Influence of Occupant Characteristics
A comparison of the fire and live loads for general and clerical offices forgovernment and private office buildings is given in Figures 10 through 13.
These figures were traced directly from histogram plots obtained using thecomputer plotting routine described in Reference 6. The intervals used to
plot the histograms were based on examination of initial plots obtainedusing standard techniques for determining the number of intervals (12). In
view of the small sample size, larger intervals were used. Note that theabscissas for these plots were terminated at a point beyond which the datain any given interval was less than one percent. Consequently, the maximumvalues do not appear. Cumulative frequency distributions obtained from thehistograms are given in Figures 14 and 15.
The distributions in Figures 10 and 11 are positively skewed. The mean fireload for private offices in Figure 11 is slightly higher (approximatelyseven percent) than that for government offices. The coefficient of varia-tion for the government offices, however, is approximately eight percentlarger. The cumulative frequency distributions for the two occupancies in
Figure 14 are quite similar and the 99 percent fractiles are almost identical(Government = 24 psf. Private = 22 psf).
For live loads in Figures 12 and 13, the mean value for government offices is
approximately ten percent higher than that for private offices. The use of
more metal furniture in government offices could account for the live load
being greater and the fire load being less than in private offices. Although
the differences are small, further examination of the data may provide an
explanation. The coefficients of variation for the two occupancies are
identical and the cumulative frequency distributions in Figure 15 are quite
similar.
The results in Figures 10 through 15 do not indicate any significant differ-
ences between the mean fire and live loads in general and clerical offices
for government and private occupancy. Further comparisons of the effect of
type of occupant on the loads for other room uses and the composition of the
fire load (interior finish vs. movable contents) are included in Section 3.6.
The influence of firm type on occupancy duration is shown in Table 23 and
Figures 16, 17, and 18. Standard classifications developed to promote
uniformity and comparability in the presentation of statistical data (11)
were used in establishing the firm types in Table 23. Occupancy duration in
this case refers to the length of time a firm occupied the particular office
in the buildings surveyed (5). It does not reflect the time period for which
the room use (general, clerical, etc.) has remained the same since the firm's
space utilization may have changed during this occupancy period. This defini-
tion is the same as that used by Mitchell in a survey in England in which
occupancy duration data were obtained by consulting telephone directories for
firm address changes over a twenty-three year period (8).
61
25
20
I
C3uu
15
GENERAL AND CLERICAL OFFICES
- GOVERNMENT
No. DBS. = 419
MAX. VAL = 44.5 psf
MIN. VAL. = 0.6 psf
MEAN = 7.0 psf
STD. DEV. = 4.6 psf
10
5
01 1 \ \ \ \ \ \ \ 1 1
0 2 4 6 8 10 12 14 16 18 20
TOTAL FIRE LOAD (PSF)
Figure 10 - Frequency Distribution of Room Fire Load Data for
Government Office Buildings
62
25
20
I
aLUCC
15
10
GENERAL AND CLERICAL
OFFICES - PRIVATE
No. obs. = 625
Max. val. = 37.2 psf
Min. val. = 1.5 psf
Mean = 7.5 psf
Std. Dev. = 4.3 psf
0 2 4 6 8 10 12 14 16 18 20
TOTAL FIRE LOAD (PSF)
ure n - Frequency Distribution of Room Fire Load Data forPrivate Office Buildings
63
GENERAL AND CLERICAL OFFICES
- GOVERNMENT
NO. OBS. = 419
MAX. VAL. = 55.6 PSF
MIN. VAL. = 0.2 PSF
MEAN = 10.0 PSF
STD. DEV. = 6.1 PSF
I \ \ \ I \ \ \ \ \ \ LZJ I [ZZL0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
LIVE LOAD ( PSF)
Figure 12 - Frequency Distribution of Room Live Load Data for GovernmentOffice Buildings
64
20
15
I
>-o
oLU
10
GENERAL AND CLERICAL OFFICES
- PRIVATE
NO. OBS. = 625
MAX. VAL. - 45.4 PSF
MIN. VAL. 0 PSF
MEAN = 9.0 PSF
STD. DEV. = 5.5 PSF
0 2 4 8 10 12 14 16 18 20 22 24 26
LIVE LOAD ( PSF)
Figure 13 - Frequency Distribution of Room Live Load Data for PrivateOffice Buildings
65
66
A3N3no3ad BAiiviniAino
67
TABLE 23 INFLUENCE OF FIRM TYPE ON
OCCUPANCY DURATION
Firm TypeNo. of Firms Occupancy Duration
(Years)
Gov't. Private Gov't. Private
Hgn c u 1 Lure 0 0
i'l 1 ii 1 iiy 0 0
Constructi on 0 8 7.4, 6. 2
Manufdcturi ng 0 29 10.1, 7 7
Transportati on 1 13 5, - 5.1 , 4 0
Trade 0 43 7.5, 9 8
Finance 0 105 8.6, 10 6
Service 8 206 15.5, 12.1 7.7, 8 1
Public Administration 58 12 7.8, 6.8 7.3, 4 4
Non Classifiable 8 8 6.0, 0 4.8, 3 2
All Firm Types 75 424 8.4, 7.5 7.9, 8 .7
*Values listed are sample mean and standard deviation - X, s
68
o
00cc
S o
>-
Ioo
>oouo
M
O
UcCO
P.3ouo
o•iH
4-1
3J3
CC
5^ 3
cCU 0)
3 Ocr T-i
0) y-i
u U-l
[1. oI
•H
SIAIdId dO UBSIAIflN
69
250
200
CO
E 150
u.OQCLU
=) 100
50
PRIVATE BUILDINGS
No. CBS. = 424
MAX. VAL. = 63 YEARS
MIN. VAL. =1 YEAR
MEAN 7.9 YEARS
STD. DEV. = 8.7 YEARS
10 20 30 40 50
OCCUPANCY DURATION (YEARS)
60
Figure 17 - Frequency Distribution of Occupancy Duration for PrivateOffice Buildings
70
250
200
CO
150
CD
100
50 -
PRIVATE & GOVERNMENT BUILDINGS
No. DBS. = 499
MAX. VAL. = 63 YEARS
MIN. VAL. = 1 YEAR
MEAN = 8.0 YEARS
STD. DEV. = 8.5 YEARS
10 20 30 40
OCCUPANCY DURATION (YEARS)
50 60
Figure 18 - Frequency Distribution of Occupancy Duration for Governmentand Private Office Buildings
71
Data on agriculture and mining firms were not obtained since they were notencountered in the buildings surveyed. For some firm types, the sample sizewas very small. A majority of the firms in the private sector were serviceor financial type organizations. Government firms were primarily publicadministration.
Mean values for occupancy duration varied between firm types. It was some-what longer for manufacturing firms in the private sector and quite a bitlonger for government service organizations. The occupancy durations for a
given firm type varied considerably and the standard deviations in Table 23are quite large in most cases. For private firms, occupancy durationsranged from less than one year to sixty-three years; for government organiza-tions from five years to thirty-three years. The mean value of occupancyduration of 8.4 years for government organizations in Figure 16 was slightlyhigher than the 7.9 years for private firms in Figure 17. In view of thesmaller sample size and the fact that most of the government buildings wererelatively new, this difference may be somewhat larger for the entire popula-tion.
The mean values of occupancy duration for the government and private buildingsand the total sample included in this survey are close to the mean value of
8.8 years obtained by Mitchell. Since Mitchell's results were obtained frommodern buildings (less than 20 years old) in downtown London, it appears thatoccupancy duration is not a function of building age.
Variation of fire and live load magnitude as a function of occupancy durationfor 1314 rooms is shown in Figures 19 and 20. The mean value does not changesignificantly with occupancy duration. The variation or range, however, is
considerably larger for the shorter occupancy durations. The sample sizesfor the longer durations were very small, however, and collection of addi-tional data could yield similar large variations. Although there is
considerable scatter, the data do not indicate any tendency for the loads to
increase with time as one might expect. The influence of occupancy durationand firm type as predictors for fire and live load magnitudes is consideredin Section 3.8.
Although no attempt was made in this survey to directly monitor load changes
with time, data obtained from the NBS Administration Building can be used for
this purpose by comparison with data obtained in a survey conducted in 1967 (4).
Results from the two surveys are given in Table 24. In comparing these
results it should be recognized that the 1967 survey involved direct weighing
and the 1974 survey used an inventory procedure. Note that the occupancy
duration for the 1974 survey is listed as nine years whereas the age of the
building in Table 3 is given as eleven years. Since the building was con-
structed in 1964 and 1975 was used to compute the ages for the buildings
surveyed, the age was considered to be eleven years. The building was not
fully occupied until 1965, however, and thus nine years was used for the
occupancy duration in Table 24. The 1967 survey was conducted after two years
of occupancy and the present survey after nine years. The number of rooms
in the two surveys was different since Floors 1, 8, 10, and 11 were not
72
60
50
40 -
107
30
20
10
0
inCD
II
COII
o
- MAX. VAL.
- MEAN
- MIN. VAL.
No. OBS. = 1314
CO CO
II CO
CO
CMII
0 10 20 30 40 50
OCCUPANCY DURATION ( YEARS )
60
Figure 19 - Variation of Fire Load with Occupancy Duration
73
128
CDd
MAX. VAL.
MEAN
MIN. VAL.
No. OBS. = 1314
05
5 o
CO
II
COCO
II
CO
IICO
II
II
10 20 30 40 50
OCCUPANCY DURATION ( YEARS )
60
Figure 20 - Variation of Live Load with Occupancy Duration
74
TABLE 24 INFLUENCE OF TIME ON LOAD MAGNITUDE(NBS Administration Building)
(a) Room Loads
SurveyDate
OccupancyDuration(Years)
No. of
RoomsSurveyed
DeratedFireLoad(psf)
LiveLoad(psf)
1967 2
335 (total) 6.3, ---
252 (offices) 6.0, -— 11.9, 5.2
1974 9 149 10.4, 6.4 15.7, 8.1
Values listed are sample mean and standard deviation - X, s
(b) Floor Loads
1967 Survey 1974 Survey
Floor Total Total
No. Survey Total (1)/ Survey Total (3)/Load Area* /(2) Load Area* M4)
(lb) (n^) (psf) (lb) (ft^) (psf)
(1) (2) (3) (4)
1 65720 11178 5.9
2
3 55217 5859 9.4 79971 6060 13.2
4 88273 5947 14.8 118229 5796 20.4
5 80849 6037 13.4 81939 5815 14.1
6 61853 6040 10.2 95130 6131 15.5
7 110099 5900 18.7 102063 6010 17.0
8 89344 5989 14.9
9 94980 6283 15.1 90191 4650 19.4
10 76861 6059 12.7
11 57310 5996 9.6
12 43027 5532 7.8 52640 6030 8.7
*Room area surveyed exclusive of corridors, lavatories, etc.
75
included in the present survey. Although various rearrangements of theoffice space took place during this time, the type of occupancy and generaluse of the building remained the same.
The results in Table 24(a) indicate that the mean live load increased by31 percent from 11.9 psf in 1965 to 15.7 psf in 1974. The derated fire load,however, increased by more than 70 percent.
The total live load on each floor is given in Table 24(b). Loads were notdetermined in either survey for the second floor which is a mechanical equip-ment floor. Note that the floor numbers correspond to those used in the 1974survey. Loads for Floors 3 through 12 correspond to values given in Reference4 for Floors 2 through 11 since the mechanical equipment floor. Floor 2, wasnot counted in that survey. The floor areas given correspond to the room areasurveyed and do not include equipment areas (elevator shafts, telephone closets),lavatories, and corridors. Slight differences exist in these areas for the twosurveys due to rearrangement of partitions and measurement errors. The differ-ence in survey area for Floor 9 was due to the fact that two of the largerrooms surveyed in 1974 were discarded due to erroneous data. The total load
increased on Floors 3, 4, 5, 6, and 12 and decreased on Floor 7. The largestincrease of 54 percent occurred for Floor 6. The total load for the sevenfloors included in both surveys increased by 16 percent [534,298 lb - 1967 vs.
620,163 - 1974]. The percent increase in the total load is approximately halfthat for the increase in the mean room live load in pounds per square foot.
This may be a result of rearranging some of the load present in 1967, i.e. someof the load may have been moved from room to room to create higher psf loadingsin the individual offices. A more detailed study of the data is required to
fully explain the differences observed.
The results for the NBS Administration Building indicate a tendency for loads
to increase with time in contrast to the data in Figures 19 and 20. It should
be noted that the values are within the scatter obtained for the 1 to 5 and
5 to 10 year intervals in Figures 19 and 20. Although the load in an individual
building may increase with time, the mean values for a given time interval con-
sidering a number of buildings may not change. This may be affected by the
occupancy with little or no increase for multiple occupancy buildings in whichfrequent tenant changes occur as opposed to an increase for single tenant
facilities. Obviously the variation of loads with time requires additional
study.
76
3.6 Influence of Room Characteristics
One parameter which may have a significant effect on the composition andmagnitude of the loads in offices is room use. Previous surveys, for example,have indicated that file rooms, storage rooms, and libraries are more heavilyloaded (4).
Survey data subdivided on the basis of room use are presented in Tables 25and 26. Data on the fire and live load magnitudes for the seven room usetypes are included for government and private offices. Since the variousroom use types occurred with different frequency in the buildings surveyed,the sample sizes vary accordingly. Very few data were obtained in somecases and this must be kept in mind when comparing the results.
Comparing the mean loads for the various room uses in Tables 25 and 26 indicatesa definite influence of room use on load magnitude. Both the fire load andlive load are larger for file rooms, libraries, and storage areas. Librariesare the most heavily loaded followed in order by file rooms and storage areas.Conference rooms and lobbies have the lowest loads. The trend is the samefor both government and private buildings. The live loads for file roomsand libraries in private buildings are quite close but the fire loads in
libraries are about 1.5 times those in file rooms. The use of metal cabinetsin file rooms may account for this decrease.
The difference between the fire loads and live loads for file rooms is muchgreater than for libraries. This may be due to the fact that filing cabinetsare usually metal whereas wood furniture is more prevalent in libraries.
Although differences exist between the loads in government and private buildingsfor the various room uses, there is no consistent trend. Whereas the live
load for general government offices is greater than that for private offices,
the reverse is true for lobbies and conference rooms. A similar trend may be
noted for the grand mean live load versus the grand mean fire load.
The results in Tables 25 and 26 indicate that room use has a significant effecton load magnitude. Note that the variability or coefficient of variation for
each room use, in most cases, is less than that for all the rooms combined.
Room use was included in the load model in Section 3.8. The question of
whether this fact should be recognized in specifying design loads for buildings
as opposed to using a constant design load throughout a given building is
obviously an economic issue. Adopting design loads based on area use within
office buildings reduces the flexibility of usage. This may be warranted in
certain cases where the owner is the sole occupant and flexibility for rental
purposes is not a constraint. The influence of room use should be included in
planning future load surveys and will be useful in identifying more heavily
loaded rooms.
77
TABLE 25 INFLUENCE OF ROOM USE ON FIRE LOAD
Room Use
GovernmentBui 1 dings
Pri vateBui Idings
No. ofRooms
TotalFire Load
(psf)
No. ofRooms
TotalFire Load
(psf)
General 342 7.3, 4.4 479 7.7, 4.3
Cleri cal 77 5.8, 5.2 Ufi 6.8, 4.0
Lobby 15 2.6, 1.4 45 5.0, 4.2
Conference 39 4.2, 6.1 57 5.9, 4.6
File 10 17.9, 11.9 20 16.2, 12.9
Storage 35 11.7, 19.2 77 13.2, 11.7
Li brary 2 30.2, 7.8 10 23.6, 10.8
All Rooms 520 7.3, 7.3 834 8.2, 6.4
Values listed are sample mean and standard deviation - X, s
(Only those rooms that were randomly selected were used for this table.)
78
TABLE 26 INFLUENCE OF ROOM USE ON LIVE LOAD
Room Use
GovernmentBui Idings
PrivateBui Idings
No. ofRooms
Live Load(psf)
No. ofRooms
Live Load(psf)
Generd
1
342 9.9, 5.9 479 8.7, 4.9
n P ri Prl 1V/ 1 C I 1 1 77 10.2, 7.0 146 10.0, 6.9
Lobby 15 2.3, 1.5 45 4.6, 4.8
Pnn "Fo y^P n ppUUI 1 1 C 1 CI iK^xz 39 5.1, 7.0 57 6.1, 5.0
File 10 27.0, 16.3 20 2A.4, 19.2
Storage 35 16.5, 23.3 77 15.5, 13.8
Library 2 34.3, 2.8 10 24.9, 9.8
All Rooms 520 10.3, 9.4 834 9.7, 8.1
Values listed are sample mean and standard deviation - X, s
(Only those rooms that were randomly selected were used for this table.)
79
The composition of the fire load according to room use and occupancy is
given in Tables 27 and 28. The percentages of the total load for interiorfinish and movable contents are given. Histograms indicating the distribu-tions of this percentage for general and clerical offices are given inFigures 21 and 22. The interior finish load consisted of: the combustibleweight (converted to an equivalent weight of cellulose) of the wall materialsand coverings such as paneling, paint and wallpaper; ceiling and floorfinish materials including carpeting; and trim such as wooden molding on
walls, doors, and windows. Furniture, equipment, and other movable itemswere included as movable contents.
The mean interior finish fire load in psf was almost identical for the variousroom uses. It was somewhat higher for private buildings than governmentbuildings. Although one might expect the type of finish materials to bedifferent for some types of room use (e.g. file vs. general), this was ap-parently not the case in this survey. Since the total fire load varieswith room use, obviously the percent contribution of the interior finishwill vary. Referring to Tables 27 and 28, this percent is greatest forlobbies and least for libraries and file rooms as expected.
Data on the influence of room size on load magnitude are presented in Tables29 and 30 for the various room use categories and occupancies. The fourarea size groups used in the tables were arbitrarily selected as representingvery small, small, medium, and large size rooms. They were not based on thefrequency of occurrence of these areas in office buildings. Note that thesedata are for rooms and do not represent the load on portions of a floor con-
sisting of two or more rooms (structural bay). In the room selection pro-cedure, rooms were selected on the basis of area being greater or less than
2200 ft . This may account for the small sample size in some cases and the
lack of data in others. It is more likely, however, that the smaller areas
are not used for certain types of rooms, e.g. conference rooms would normally2
be larger than 50 ft .
For general and clerical offices in Tables 29 and 30, the mean load decreaseswith increasing area. There is no apparent trend for the other room use
categories which may be due to the small sample size in most cases.
The influence of room size on live load magnitude is further illustrated in
Figures 23 through 26. The types of room use and both occupancies were com-
bined for each area size group for the histograms shown. The distributionsfor all the size groups are positively skewed and do not seem to approach a
normal distribution as area increases. The coefficient of variation is quitehigh for three of the four groups. This may be due to the smaller sample
size for these cases. Except for the largest size group, the variability as
measured by the coefficient of variation seems to decrease as area increases.
Mitchell's data (8) indicated this same trend and his data for various areas
showed similar large scatter.
80
TABLE 27 COMPOSITION OF TOTAL FIRE LOADBY ROOM USE FOR GOVERNMENT BUILDINGS
Use
No.
of
TotalFi re
Load*(psf)
Interiorr 1 M loll
Fire
Percent of Total Fire Load**
RoomsLoad* Interior
Finish
Mnvflbl
p
Contents
art o a 1bcricra 1
7 & A. 17 83
L 1 er 1 La
\
77 0 . O ) D > c. \ • L. , U.J 20 80
1 ohhv 1 5 2.6, 1.4 1.3, 0.4 50 50
Conference 39 4.2, 6.1 1.2, 0.4 29 71
File 10 17.9, 11.9 1.2, 0.6 7 93
Storage 35 11.7, 19.2 1.2, 0.5 10 90
Library 2 30.2. 7.8 1.0, 0.1 3 97
All Rooms 520 7.3, :.3 1.2, 0.4 17 83
*Values listed are sample mean and standard deviation - X, s
**Values listed are sample mean
(Only those rooms that were randomly selected were used for this table.)
81
TARLE 28 COMPOSITION OF TOTAL FIRE LOADBY ROOM USE FOR PRIVATE BUILDINGS
RoomUo c
No.
of
1 Ota 1
Fi re
Load*(psf)
T jrhpyi nv*1 1 1 i- Cl 1 U 1
FinishFireLUCt U
(psf)
Percent of Total Fire Load**
InteriorFinish
Movabl
e
Contents
General 479 7.7, 4.3 1.9, 0.4 24 76
Clerical 146 6.8, 4.0 1.7, 0.5 25 75
Lobby 45 5.0, 4.2 1.7, 0.6 34 66
Conference 57 5.9, 4.6 1.8, 0.4 30 70
rile 20 16.2, 12.9 1.8, 0.6 11 89
Storage 77 13.2, 11.7 1.7, 0.9 13 87
Library 10 23.6, 10.8 1.8, 0.4 8 92
All Rooms 834 8.2, 6.4 1.8, 0.5 22 78
*Values listed are sample mean and standard deviation - X, s
**Values listed are sample mean
(Only those rooms that were randomly selected were used for this table.)
82
40
30
o
aUJ
20
10
0
GENERAL AND CLERICAL OFFICES
- GOVERNMENT
No. obs. = 419
Max. val. = 1.0
Min. val. = 0.02
Mean = 0.24
Std. Dev. =0.17
rzL0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
INTERIOR FINISH FIRE LOAD
TOTAL FIRE LOAD
Figure 21 - Percentage of Interior Finish Fire Load - Government Offices
83
30
25
20
cdLU
15
10
5-
0
GENERAL AND CLERICAL OFFICES
- PRIVATE
No. obs. = 625
Max. val.= 1.0
Min. val. = 0.04
Mean = 0.32
Std.Dev. = 0.19
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
INTERIOR FINISH FIRE LOAD
TOTAL FIRE LOAD
Figure 22 - Percentage of Interior Finish Fire Load - Private Offices
84
COCDc
:303
QJ —
~
S- M-•1— COu_ a.
X I—(O ra
T3 >+J O)
CXI CO IJD
r-. CM CO COOO (NJ CM
un en CO
'd- r— "^J- oo
r~- CTi ct.'
CO tr)
I— CM — I—
CVi CM CM
CO un CO CO
en I— CO CO
O O CD LD
CD CX3 cc en
CM 1^CM
CT) COI • • .
I CM CM
— 1— r-~.
I CO CM
I en CX) ^I CM
cn CT> oI . • •
I CM ^ I—
CO CO CO
r-~ CO CO
CO tn o CM
en CO CM en^ «^ CM
CTl O >— LT)
CO CO LD O
O CO CO CT^
CTl CO CTl ^CO I—
00 .— CO c*-
1— cn CO oen CO CO
CO ^ CO r—
CM CM i— CTl
CO CO CTl en
CO CO I— r-.
I r-. CTl CTl
I i— CO CM
1— CM
O M- O^ o or-^ 1
—
c? CO 00CO 1— CO CO
.— CO <^CO CM
CTl I—I— ^ CM r—
LOO CO ^ CTlo
CM 1— tn COCO CO
CM I— CM CO
3CQ
cS-
cu>oC3
oo
4->
o
un CM or— CM 1—
I r--. 1— LT)
I CM CO 1—
CO 1— CD
ICM ^ CD O CM I
—
CM
O CD CO
CM CO CM COO CcJ CM CO
T3 >+-> CD
O CO CMCM
CD CO
1— IT) CO
t~- LO r-^
I • • •
1 O I— t—
cn CO
I — 00 I OC CO
CM 00 CO cn
1— I— CD CMr—
CO CO CO
o I—^LD
CO
CO CM COI • •
I 1— CO "CJ-
I— LD 00
1 CM CM CM
CO CO
I CO
t-x c00
cd - CO r— CO
CO ^CM I—
O O^ o oI— CTl LO
CM .— CM COCD r-^O ^ CO CO o CM CXI cn
CO •—O O r— CM O O LD LO
CD OCO CD r— >— O O 1— —
to CMCDs. +-
ooa:
o oo or— COvl vl
I I
O O O Ocn LD o o
1— COvl V V A
CD
o oo or— CO
O O O OLT) LO O Ovl V V A
o oo oI— COv| VI
I I
o o o oun cn o o
r- COV| V V A
o
o oo o.— COvl Vl
I I
o o o oUO IT) O O
r— CO
o oo oI— CO
o o o ocn LO o o
r—
o oo oI— COvl v|
I
o o o ocn cn o o
1— COvl V V A
tos_
o
o oo oI— COvl vl
I I
o o o oun un o O
I— CO
>1S-
i.J3
o(_>
85
3CO
CD+->
QO
-a
o
X I—
o >-l-> O)
O 4- O^ o o
rv. CTi
LT) LTi cn ^^ CM OO CNJ
':a- o ^r-^ uo ^ Lo
<Nj cr a^ i£>
LT) 1— r-^ t--.
<NJ I—
I
—
O OO 00CO 1— ro OO
uo «^ <^
oc CO OO— OO CM cvi
O CJ^ -^j-
O CX3 LT)
CM
1^ UD r~- cr
ro CTi Ln i£
LO I— si - CTl
^ <x> CTi r--.
— CO -id-
oo CM r-^ "cj-
CXD OO cx>
I OO LT, CM
r— t-D 00
I OO Lf) CVJ
cn I—1— ^ CM I—
I r-^ o cI OO r—
CO ^I o un CM
r-. Ln 00
I isD to CO
o CO cn
CO r--. o ovt 1— O
LO CO 1
—
CM CM CM OO C» 00 CMCM I—
O CM 1— >;d-
c CO CM cx;to CM CM
to CTi t\ to
CT^ «d- CM sd-^ LT)
>— CM O r—
CO LD ^ -^t
CO I— < O^ to LT) O
oCM 1— LD CO
CO toCM 1— CM to
I CTi 00 CI I— OO CO
>— 00
I CO o
I to I
I 1— CM I
O CM r-~. I
—
t—l
oo
oUJo
oCO
an
o
ca
s_
>oCD
X5
O
s: >
to Ln CM CM
to to LO ^Ln 1— CO 1
—
I .— .— CO1 CO CM
00 00 1^
1— >d- un
TD >4J CDC/1 Q
LT) ^ tn i
—
1— CM LO OOCM
1 CM r~~ to
«a- cn o oo o o^ I— I—
— 00
I LD O CTi
r— CM CI I— CM
O M- O^ O O CM OOto t---o ^ cn o CM CO Ln
CTi CM
I CM cn
CMS3- to
CO CO 1—
LO r-^ cn CMCM CM Ln
h-^ Ln
I Ln
CO r—O O — CM
r-^ CMCM
cn CM 1— to
CM cn cx;
I 0-. ^I CM CM
CO CT) O CCO 1— 1— O
CO t— CM
O o Ln Lnto o
CO to 1— 1—
I CM toI CO CO
O O r— ,—
fO CMQJS- +
Eoo
o oo o1— OOVI v|
I I
o o o oLn Ln o o
1— COV| V V A
S-cucCI5
o oo o1— OOVl VI
I
o o o oLn Ln o o
o oo oI— COvl v|
I I
o o o oLn Ln o ovl V V A
-Q
O
O OO OI— COvl v|
I
o o o oLn Ln o o
I— COvl V V A
OloCDs_
o
o oo or OOvl V|
I I
o o o oLn Ln o oVj V V A
O OO OI— OOV| V(
I
o o o oLO Ln o o— CO
QJcnto
o
o oo oCO
'7l V|
o1
o1
OOLn Ln OO
1— 00vl V V A
c:O
86
30
20 -
I
>-o
LU
ALL ROOMS
50 FT^ > AREA)
NO. OBS. = 41
MAX. VAL. = 74.3 PSF
MIN. VAL. = 0 PSF
MEAN = 17.4 PSF
STD. DEV. = 17.1 PSF
10
10 20 30 40 50
LIVE LOAD ( PSF)
60 70
Figure 23 - Load Intensity versus Area of Room - Area <_ 50 ft
87
30
^ 20
I
>-
C3UJ
10
ALL ROOMS
50 FT^ < AREA < 100 FT^
NO. OBS. = 188
MAX. VAL = 127.7 PSF
MIN. VAL. .= 0 PSF
MEAN = 13.2 PSF
STD. DEV. = 12.5 PSF
10 20 30 40
LIVE LOAD ( PSF)
9 0Figure 24 - Load Intensity versus Area of Room - 50ft < Area < 100 ft
88
r
40
30
I
>-
LUcc
20
10
0
ALL ROOMS
( 100 FT2 < AREA < 300 FT^)
NO. DBS. = 899
MAX. VAL. = 52.7 PSF
MIN. VAL. = 0 PSF
MEAN = 9.2 PSF
STD. DEV. = 6.4 PSF
10 20 30 40
LIVE LOAD ( PSF )
50
2 2Figure 25 - Load Intensity versus Area of Room - 100 ft < Area _< 300 ft
89
40 r-
30
I
o20
10
0
ALL ROOMS
( 300 FT^ < AREA)
NO. OBS = 226
MAX. VAL = 62.7 PSF
MIN. VAL. = 0 PSF
MEAN = 8.7 PSF
STD. DEV. = 8.9 PSF
i 1
0 10 20 30 40
LIVE LOAD ( PSF)
50
Figure 26 - Load Intensity versus Area of Room - 300 ft < Area
90
The data in Figures 23 through 26 indicate that the mean load decreases^
significantly as area increases. The mean for areas greater than 300 ft ,
for example, is only fifty percent of that for areas less than 50 ft . Thisdecrease is considerably different from that observed by Mitchell. This is
apparent from the following comparison:
Present Survey
Area Range
(ft^)
No.
Obs.
MeanLiveLoad(psf)
Std.
Dev.
(psf)
Coeff.Var.
99%Fractile*(psf)
0- 50 41 17.4 17.4 1.00 74.350-100 188 13.2 12.5 0.95 127.7
100-300 899 9.2 6.4 0.70 33.4>300 226 8.7 8.9 1.02 52.1
* Fractile values obtained directly from ordered data.
Mi tchel1
' s Survey(Reference 8)
Mean MeanNotional No. Live Std. Coeff. 99%Bay Area Calc. Load Dev. Var. Fractile
(ft^)(psf) (psf) (psf)
25.3 8840 13.8 13.5 0.98 62
56 14290 13.4 11.0 0.82 52
151 20442 13.0 8.9 0.68 44
336 14283 12.8 7.2 0.56 37
624 6511 12.3 6.3 0.51 32
1197 1885 12.2 5.5 0.45 30
2069 1152 11.8 4.5 0.38 25
91
It is important to note, however, that the basis used to obtain the loadspresented herein was different from that used by Mitchell. Mitchell includedthe weight of people and assumed certain loads for some areas (corridors,stairways, lavatories, etc.) whereas this was not done in this survey. Also,Mitchell obtained loads per unit area using portions of a floor and subdividingthese portions into rectangular bays (notional bays) of varying area and aspectratio. These notional bay areas did not necessarily coincide with the parti-tions and consequently, Mitchell's values are not loads per unit area fora room.
The decrease in mean live load with increasing area is much greater for roomloads than for the notional bays. This is probably due to the effect of thenotional bay concept unless significant differences existed between the twosurvey samples. For the smaller notional bay sizes, for example, some of
the bays would consist primarily of small heavily loaded rooms while otherswould be pieces of larger more lightly loaded rooms. The overall mean,therefore, would be less than that for the small rooms which is the casefor the data given. Similarly, for large notional bays some of the bays wouldconsist of lightly loaded large rooms whereas others would consist of several
smaller more heavily loaded rooms. The overall mean would be larger than
that for the large rooms which the data above indicate. For the 99% fractiles,the notional bay values are less than the room values. This may be due to
the considerable difference in sample size or the survey samples themselves.Except for the large rooms, the coefficients of variation for the room loads
and notional bay loads are about the same and follow the same trend, i.e.
decrease as area increases.
The relationship between mean load and room area is also shown in Figures 27
2through 30. Here room area intervals of 50 ft were used as opposed to the
four groups in Figures 23 through 26. The data in these figures seem to
follow the same trend noted previously, i.e. the mean load decreases withincreasing room area. In view of the apparent influence of room area on load
magnitude, this parameter was included in developing the load models in
Section 3.8.
92
CO
Std
Dev.
(I
W 00 r~ '
'
Mean
(psf)
LO 05 CO1 ^
No
obs
CD CO ^ O fSJ
O)c(BOC
1200
2000
2000
3000
3000
4000
4000
6000
6000
9000
LUu
NT
OFFI
=
630
ERNME
No
obs.
GOVI
I = N
z
e = N
Z-- N
= S = N
E == N
E == N
E == N
= s
= N_
3 == N
}sil 81'
= s 01 = N
jsd 0 91 = s 6 = N
|sdI E
= s U = N .
|sd g e = s OE = N
jsd 0 8 = s Zt, = N
jsd ^ 9 = s = N
isd i e = s >i = N
|sd 6 E = s 08 = N
|sd 8 9 = s EOl = N
jsd = s 091 = N
isd 5 13 = s >2 = N
jsd 8 81 = s '9 = NI
Ooo
oo
ooCD
o
tn o Ln
(dS(J) OVOl im IViOi NV3I/\I
93
(dSd) QVOI 3aid IVIOI l\IV3l/\l
94
>Q3 .
o55
s ;^ ^ 1 1
Mean(psf) r- ^ 1 ^
CO oo 1 ^2
£ 4 CO CO ^ O rsi
OJ
1200
2000
2000
3000
3000
4000
4000
6000
6000
9000
E = N
I = N
il
|sd 8 9
Z
Z
o
o
oooo
t<LUcc<
oooc
oo
M0)
u•H
o
(U
>O
cd
<u
soo
to
3to
VI
<u
>
to
ohJ
(U
>•H
(U
M300•H
(dSd) avol 3An NV3IAI
95
t 1CO 00 ^
11
psj ob 1
'
1 IcNj ^ n <pO ub t*^
i ^ CO O) ^ CN
LU . .
CD CNi
1200
2000
2000
30O0
3000
4000
4000
6000
6000
9000
Z = N
Z = N
Z = N
Z = N
jsd ^ 6 = s > = N
£ = N
3 = N
jsd 9 9 = s = N
}sdG>= s 8 = N
)Sd itt = s tl = N
jsd g 6 = s 92 = N
ja) 91 = s 68 = N
}sd 2 9 = s £9 = N
69 = s eg = N
isd 99 = s 'ifrl = N
>srf 1 9 = s 683 = N
isd 28t = s 991 = N
isd 8 91 = s = NI
o
oooo
ooCO
oo
o
(dSd) aVOl 3An NV3IAI
96
3.7 General Results
The survey data provided detailed information on the characteristics of roomsin office buildings in addition to the loads discussed in previous sections.This included information on the bounding surfaces, openings, and room con-tents which is summarized in this section. Numerous additional studies canbe made using the data collected.
The characteristics of the bounding surfaces (walls, floor, ceiling) are ofinterest with respect to fire growth and fire severity studies. Data onthese characteristics are presented in Table 31. For each item, the typesof material correspond to the choices available on the data collection form.The number of occurrences for each of the 1354 rooms and the frequency ofoccurrence are given. The sample size for the walls was obviously four timesthat of the room sample. Referring to Table 31, it may be noted that:
(1) the ceiling material was acoustical tile in most cases, (2) the majorityof floors were covered with carpet or resilient tile and very few wood floorswere encountered, (3) most doors were metal although many doors had a plasticveneer type finish, (4) most baseboard molding was rubber or metal, (5) non-combustible and metal wall panels were predominant (some rooms with one ormore open walls occurred - wall material not present), and (6) the majorityof the walls were painted.
Since the severity of a fire in a room is affected by the dimensions of the
openings through which air for combustion can be supplied, data on the doorsand windows in the offices were obtained. These data are presented in Table 32
according to room use and occupancy type. The percentage of wall area com-
posed of doors and windows and the opening factor or temperature factor are
given. The fire duration in hours is directly related to the fire load and
this opening factor (13). The percentage of door and window area appears to
be related to room use with file rooms and storage rooms having the smallervalues as expected. In most cases, rooms in private buildings have a larger
percentage of door and window area. The opening factors for governmentgeneral and clerical offices in Table 32 are approximately equal to the
"medium" values for this parameter used in analytical studies by Lie and
Stanzak (14). The values for government lobbies, conference rooms, and file
rooms are close to their "small" values. The opening factor for privategeneral of'fices agrees with their "large" opening factor. Note that the
opening factor for each room use in Table 32 varies considerably and in most
cases the coefficient of variation is greater than one.
Data on the number of concentrated loads in offices are given in Figure 31.
The number of loads in this case refers to discrete individual floor loads.
For example, a cabinet, including its contents and items on top of the cabinet,
was considered as one load. The total includes all items from heavy pieces
of furniture such as desks to small light items such as wastebaskets . The
mean number of items was eighteen and the maximum 304. The large number of
loads occurred in office landscape type areas, i.e. open office space comprising
almost an entire floor. The few offices with a very large number of loads
also account for the large coefficient of variation ( ttV = 1.6). About six
percent of the rooms, primarily lobbies, contained five items or less.
97
OO COO LU
I— =!
(_) CD< z:
Not Present
I j
ocr.
.
CO "3-
1 00 CDIT) .
ro c£)743
13.7
ns
and
Percent
of
Total
Paint4023 74.3
Vinyl
CM un
Drapesr-* •
ro KO
Paper
Gypsum
Board1951 36.0
Plaster
V£> CNJCO •
ro «x<
Rubberi
—
ro •
in
Carpet 85663.2
F
Observatio
Res.
Flooring
32524.0
lumber
ol
NonComb.
in LT)
— CO159
11.8
1038 19.2
Acoustical Tile
1227 90.6
Plastic
•<3-
O 46934.6
O CTiCVI .
f— 00^ .
CM O
Metal O1
73754.4
«X> CTI
cn .
OJ —CVJ
1658 30.6
Wood'~ o
o^ .
.
oCM
00 •
CO o O
1
Item
Ceil
ing
Floor Doors
1
Floor
Trim
|
Wall
Materia*
Wall
Covering!
oo o
o _.c _
ra
98
TABLE 32 SUMMARY OF DATA FORDOORS AND WINDOWS
uccupdncy rxUUlM l\ln nf Dn n A v^p a nine Ul i n r\n\fj A k'o ;iUU Ui nrcu |J)Uo will UUW n 1 c a INO . OT
Type Use Rooms Total Wall Area
X 100
Rooms* FactorAx/iT / A TM V n / n
1
General 342 12.7, 7.6 294 0.117, 0.103
CI erical 77 11.2, 7.4 50 0.089, 0.08^
Lobby 15 14.8, 10.9 11 0.034, 0.057
bovernincrii LU 1 1 1 c r CI 1Q 9 C C0. £ , D. 0
•37 n n'3? n n^?
r M c 1 n1 u D. U, 3.0 O
35 0 008 0 032
L 1 u r d 1 y C c 0 064 0 090
General 479 17.8, 9.2 453 0.185, 0.136
CI eri cal 146 13.3, 8.0 112 0.090, 0.110
Lobby 45 14.5, 9.0 32 U.U23, 0.046
Pri vate Conference 57 14.1, 9.9 56 0.087, 0.138
File 20 11.1, 7.3 17 0.050, 0.111
Storage 77 9.0, 7.0 70 0.007, 0.032
Library 10 6.8, 4.7 7 0.035, 0.066
Values listed are sample mean and standard deviation - X, s
A = Total window area
H = Height of window in feet
Ay = Total area for internal surfaces of room (walls, floor, ceiling)
*The opening factor was not computed for rooms without four full height walls.
(Only those rooms that were randomly selected were used for this table.)
99
40
30
>-o
C3LU
20
10
00 10 20
ALL ROOMS
NO. DBS. = 1354
MAX. VAL. = 304
MIN. VAL. = 0
MEAN = 17.6
STD. DEV. = 28.5
30 40 50
NUMBER OF DISCRETE CONCENTRATED LOADS
Figure 31 - Number of Discrete Loads in a Room
100
The characteristics of the types of furniture items observed in the officessurveyed are given in Table 33. The total number of desks, tables, etc. inthe 1354 offices and the construction material are indicated. The materialtype in this case refers to the primary construction material and does notinclude laminate material used as a finish surface. The number of metaldesks encountered was about twice the number of wood desks. The reversewas true for tables, however. As expected, the majority of filing cabinetswere metal. General purpose cabinets were equally divided between the twomaterial types. In the total survey only four pieces of plastic furniturewere encountered.
The weight of heavy individual furniture items in offices is of interest inlive load design. Existing standards, for example, require that floors bedesigned for concentrated loads in addition to the specified uniformly dis-tributed loads. The frequency distribution for the heaviest load in each ofthe rooms surveyed is given in Figure 32. The maximum load encountered was3280 lb. The mean for all the offices was 451 lb. The coefficient of varia-tion of 0.63 for these data is of the same order of magnitude as that for theuniformly distributed live load (Figures 12 and 13 - 0.61) The 99 percentfractile load for the data in Figure 32 is 1748 lb which corresponds closelyto the value of 2000 lb specified in existing standards for office buildings.
The amount of paper and books in offices is of interest with respect to fireconsiderations. The degree of compaction of this material is also importantsince it affects the rate at which it will burn. Table 34 lists the observedpercent compaction of paper and books for various furniture items in the
survey. Paper and books on top of furniture which are immediately availablefor combustion (free contents) and enclosed paper and books within drawers,shelves, etc. are listed separately. Since enclosed contents refer only to
material completely enclosed on all sides, there are no data for enclosedpaper and books for shelving, seating, and miscellaneous items. The numberof observations in each case refers to the number of distinct piles or stacks
encountered for all the desks, tables, etc. The data indicate that piles of
paper occurred more frequently than piles of books. The number of piles
of free and enclosed paper were about the same for desks. For cabinets,
the number of enclosed paper piles was twice the free content piles. The
percent compaction generally ranged from 85 to 95 percent.
The spatial distribution of the loads in a room is important from the stand-
point of the live load effect on the structural systems and the transmission
of heat to the bounding surfaces in the case of a fire. Data on this distribu-
tion are presented in Figures 33 and 34 and Table 35. The data in Figures 33
and 34 indicate a definite tendency for the items in a room, particularly the
heavier items which contribute the major portion of the total room load, to be
located near the walls (within 2 ft). Both distributions indicate a negative
skew although there appears to be an slight tendency toward a bimodal distri-
bution. Apparently in arranging the contents of offices, the occupant either
101
TABLE 33 CHARACTERISTICS OF ROOM FURNITURE
Type of Item Total No.Number of Observations and
Percent of Total
Wood Metal Plastic*
Desk 2162 755
34.9
140765.1
0
Table 150291260.7
589
39.2
1
0.1
Fil ing Cabinet 1608
74
4.5
153^
95.40
Fil e Safe 322
6.3
30
93.80
Blueprint Cabinet 23 0 23
100.00
Card File 1207
5.8
113
94.2nu
General PurposeCabinet
10^8503
48.0
544
52.0
1
0.1
Bookcases 1014356
jD. 1
6580
Free Shel ving 521247
47.4
272
52.2
2
0.4
Ch ai rs
(Frame material
)
4588284061.9
1748
38.10
Government and private - sample size = 1354 rooms
*Does not include wood or metal items with plastic laminate finish surfaces
(Only those rooms that were randomly selected were used for this table.)
I
I
102 i
ALL ROOMS
NO. DBS. = 1354
MAX. VAL. - 3280 lb.
MIN. VAL. = 0 lb.
MEAN = 451.4 lb.
STD. DEV. = 284.7 lb.
0 100 200 300 400 500 600 700 800
MAGNITUDE OF HEAVIEST LIVE LOAD ( LB)
Figure 32 - Magnitude of Heaviest Room Load
103
TABLE 34 COMPACTION OF PAPERAND BOOKS
Type of Item
Percent Comoaction for Paoer and Bnnk<;
Fr pp Enclosed
Total No,
of Obs.
Free
BookTotal No.
of Obs.
FreePaper
Total No.
of Obs.EnclosedBooks
Total No.
of Obs.EnclosedPaper
Desk
636 90.5 1999 96.8 789 87.8 1949 84.9
Table 432 88.3 850 94.8 33 93.9 165 95.9
Cabinet 635 87.0 1031 93.9 699 81 .8 2318 82.7
Shel ving 958 83.5 897 88.0
Seating 1 100.0 3 93.2
Miscellaneous 46 92.0 252 83.9
Government and private - sample size = 1354 rooms
Values listed are sample mean and standard deviation - Y, s
(Only those rooms that were randomly selected were used for this table.)
104
t
20
15
>-
C3LJLl
10
0
ALL ROOMS
NO. OBS. = 1354
MAX. VAL. = 98.9%
MIN. VAL. = 0%
MEAN = 52.6%
STD. DEV. = 26.8%
0 10 20 30 40 50 60 70 80 90 100
PERCENT OF MOVABLE FIRE LOAD WITHIN
TWO FEET OF WALLS
Figure 33 - Distribution of Fire Load in Rooms
105
i
40
30
ALL ROOMS
NO. OBS = 1354
MAX. VAL = 100%
MIN. VAL = 0%
MEAN = 75.6%
STD. DEV = 28.0%
>-C_3
20
10
10 20 30 40 50 60 70 80 90 100
PERCENT OF LIVE LOAD WITHIN
TWO FEET OF WALLS
Figure 34 - Distribution of Live Load in Rooms
106
TABLE 35 SPATIAL DISTRIBUTIONOF ROOM CONTENTS
Type of Item Government Offices Private Offices
No. ofItems
Percent within2 feet of walls
No. ofItems
Percent within2 feet of walls
Desk 965 55.
1
1197 55.5
Table 847 69.8 655 61 .8
Cabinet 1217 95.7 1614 84.6
Shel vi ng 716 72.5 819 81 .7
Seating 3891 35.0 4162 31 .8
Miscellaneous 2979 65.2 4310 54.7
Government and private - sample size = 1354 rooms
Values listed are sample mean
(Only those offices that were randomly selected were used for this table.)
107
locates most of the items close to the walls or a very small portion nearthe walls, the former case occurring more frequently. The mean values ofthe live load and fire load within two feet of the walls were 75.6 percentand 52.6 percent respectively. The lower mean for the fire load percentagemay be due to the fact that the derated movable fire load was used in Figure34.
The spatial distribution of the various types of furniture items is givenin Table 35. As expected, cabinets and shelving are more frequently closeto the walls. About half of the desks and somewhat more than half of thetables were within two feet of the walls. Most of the seating was greaterthan two feet from the walls. Although some differences occurred betweenprivate and government offices, there is no apparent trend.
The percentage of the room floor area occupied by furniture provides an
indication of the degree to which office space is utilized and is an importantconsideration relative to the amount of space available for additional furni-ture loads or loads which could occur due to people crowding into a particularroom under certain circumstances (emergencies, parties, etc.). Obviously, thesmaller the percentage occupied, the greater the additional load could be.
Data on this parameter are given in Figure 35 for general and clerical offices.About 60 percent of the data fall in the 20 to 40 percent range with a meanvalue of 33.5 percent. The variation (coefficient of variation = 0.42) is
somewhat less than that discussed previously for load magnitude and the dis-tribution is approximately normal. The variation of this ratio as a functionof the area of the room is presented in Figure 36 for all the room use types.The mean value seems to decrease slightly with room area. For rooms less than
2100 ft , approximately 40 percent of the floor area is occupied. This value
decreases to between 25 to 30 percent for larger areas. Table 36 summarizesdata on this parameter as a function of room use. The fractile values wereobtained directly from the ordered data. The minimum values of zero correspondto empty offices and lobby areas with no live load. The mean value of the
occupied floor area was approximately the same for the different room uses
except for lobbies. The scatter of coefficient of variation was much largerfor storage rooms than the other uses. More variation occurred for the 95
percent fractile, however, with the largest values being for clerical offices
and storage rooms.
The survey data presented thus far indicate that a variety of factors may affect
the load characteristics and loads in offices to varying degrees. Although
the concept of discussing these quantities in terms of a "typical" office is
questionable, it is of interest to summarize the mean values. Data on factors
related to fire consideration are given in this form in Table 37 for the 1044
randomly selected general and clerical offices in the survey. Mean values for
both the total and derated fire loads, the movable contents and interior
finish fire loads, the characteristics of these loads and information on the
openings are included. Derated fire loads were obtained using the derating
factors presented in a previous report to account for the estimated quantity
of enclosed combustibles which will burn in a fire (5).
108
35
30
25
>-
C3uucc
20
15
10
GENERAL AND CLERICAL OFFICES
No. OBS. = 1044
MAX. VAL. = 140 %MIN. VAL. = 0%MEAN = 33.5%
STD. DEV. = 14.0 %
0 10 20 30 40 50 60 70 80
(OCCUPIED FLOOR AREA/TOTAL FLOOR AREA) xlQO
Figure 35 - Frequency Distribution of Loaded Floor Areas
109
o oCO
o
I
e
I
z
II 0 - s '9
I
80 0 = s '9 - N
a O = s '9 = N
130 = s-9 = N
90 0 = s > = N
Z = N
80 0 = s '6 = N
61 0 = s 'u = N
810 = s EL = N
a o = s '91 = N
910 = s '9t = N
92 0 = s '99 = N
21 0 =s '8^ = N
21 0 = s 'IK = N
II 0 = s '982 = N
n o = s >n - N
IVO = s '881 = N
98 0 = s 'Ofr = N
a3H3A03 V3aV aOOId iN33y3d NV3IAI
Figure 36 - Variation of Occupied Area with Floor Area
no
TABLE 35 SUMMARY OF OCCUPIED FLOOR AREA
Room Use No. of Occupied Floor Area/Total Floor Area
RoomsMt r> 1 mi im
Val ue
LOW c r 0/0
Fracti 1
e
MaximumValue
Upper 95%Fracti 1
e
MeanValue
oLdilUdrCJ
Devi ation
General 818 0.0 15.6 90.2 53.9 33.1 12.4
CI erical 222 0.0 13.7 97.9 73.8 3^.1 17.0
Lobby 60 0.0 0.0 65.2 43.4 20.2 13.8
Conference 95 9.7 15.^ 84.6 59.5 36.1 14.1
File 30 1.2 5.9 87.1 62.9 35.4 19.1
Storage 111 0.0 0.0 92.1 75.0 27.5 21 .0
Library 12 22.1 58.3 36.6 10.9
Government and Private Buildings
(Only those rooms that were randomly selected were used for this table.)
ni
TABLE 37 PROFILE OF OFFICE FIRE LOADS
General and Clerical Offices - Sample Size = 1044 offices
(Government and Private)
1. Total fire load = 7.3 psf, 4.4 psf
2. Total fire load (derated) 6.6 psf, 4.1 psf
3. Movable contents fire load
(derated) 5.0 psf. 4.0 psf
4. Interior finish fire load = 1.6 psf. 0.5 psf
5. Percent of total derated fire load
enclosed in metal containers 9.1%, 12. 4%
6. Percent of furniture and miscel-laneous items within 2 feet of1"hp wa 1
1
= 70.2%, 20. 4%
7. Percent of total fire load
within 2 feet of the walls = 55.1%, 23. 6%
8. Percent of total fire load
that is paper and books = 38.6%, 22. 9%
9. Number of free standing items 16.9, 27 .6
10. Opening Factor (A /IT/Ay)** = n.146 ft^/^ , 0.127 ft^''^
11. Percent of floor area occupied = 34%, 19. 1%
* Sample Size = 1034
**Sample Size = 909
Values listed are sample mean and standard deviation - X, s
(Only those rooms that were randomly selected are used for this table.)
112
following observations can be made from the data in Table 37:
(1) The derated fire load is approximately 90 percent ofthe total fire load,
(2) Movable contents comprise approximately three-fourthsof the derated fire load,
(3) The majority of the furniture items are within two feetof the walls,
(4) Paper and books account for approximately 40 percentof the total fire load, and
(5) On the average, 34 percent of the floor area is covered
by furniture, equipment, etc.
113
3.8 Load Models
As indicated in the Introduction, the purpose of this survey was to identifythe factors affecting the magnitude of loads in office buildings and tothen develop a mathematical model for predicting future loads. The modelcould be used for future building populations with a different relative mixof building and occupant characteristics (building height, firm age, etc.)than the current population surveyed. It was assumed that time would notsignificantly change the effect of the various parameters, e.g. if the loadmagnitude in present-day buildings is related to room use and file rooms areX percent heavier than clerical offices, file rooms in future buildings wouldcontinue to be x percent heavier than clerical offices. This assumptionregarding time effects obviously needs to be verified.
The influence of building and occupant characteristics on load magnitude canbe considered at two levels, loads in rooms and loads on larger areas suchas structural bays. The latter is obviously more significant from the stand-point of design requirements. Factors such as room use and area can bereferred to as "local" factors and may affect the loads in individual rooms.One would expect, however, that these mean room loads would not be affectedby factors such as building height and building age. The loads on largerareas or structural bays, however, may be affected by these building factorssince the arrangement of rooms may be related to building height, type of
occupancy, etc. The survey data may be used for both cases. The analysisin this report considers only loads in rooms. The influence of buildingfactors (i.e. arrangement of rooms in the buildings) on loads on structuralbays can be determined using the floor plan data (6). Additional analysisis required to determine this influence.
Since the twenty-three buildings did not conform to a factorial experimentdesign, a linear regression analysis was used to derive the mathematicalmodels. A step wise regression analysis of the data was carried out using
the BIOMED computer program (6). The following form was used for the
mathematical model
:
n
E[Y] = C + E C .X
.
X 0 .T -C
The term, C^x^ represents the main effect of the variable x^. Several
combinations of variables were used in order to identify the significantfactors. Regression analyses were carried out using the following combinations
(1) room use; (2) room use and room area; (3) room use and firm type; (4) room
use, firm type, and geographic location; (5) room use, firm type, geographiclocation, occupancy duration, building age, building height, and room area.
In all cases, room use was found to be the most significant factor, i.e. it
contributed almost all the variance in the live load and fire load accountedfor in the regression analysis. Room use, therefore, was the only variable
included in the mathematical models [Equations 1 and 2] .
114
The mean and standard deviation for the data from all the 1354 rooms wereas follows: Live Load - x = 9.9 psf, S = 8.6 psf; Total Fire Load - x =
7.8 psf, S = 6.8 psf. The final equations developed from the regressionanalysis give the following predicted mean values:
Mean Live Load (psf) = 13.8 - 4.6x^ - 3.7x2 " ^'^^3
- 8.1x4 ^ Tl-Sxg + 2.0Xg
.12.7x7(1)
Mean Total Fire Load (psf) =11.1 - 3.6x^ - 4.7x2 " ^•'^^3
- 5.9X4 ^^-^^S ^-^^6
+ 13. 6x-(2)
The independent variables x. in Equations 1 and 2 correspond to the followingroom use types:
x-| - general office
X2 - clerical office
x^ - lobby
X4 - conference room
Xg - file room
Xg - storage room
x-j - library
Each variable takes on the value of one or zero and only one of the seven is
nonzero at a time depending on the type of room for which the equations areused. For example, the mean live load for storage rooms is obtained fromEquation 1 by setting x-j = X2 = x^ = x^ = x^ = x^ = 0 and Xg = 1 , i.e.
E [Live Loadl^^Q^ggg = 13.8 + 2.0 = 15.8 psf. The standard deviations
associated with Equations 1 and 2 obtained from the average of the squaredresiduals in the regression analysis are 7.8 psf and 6.2 psf, respectively.The magnitude of the coefficients in Equation 1 suggest that some of the
room types could be combined as follows: general and clerical; lobby and
conference; and file and library which would reduce Equation 1 to fourindependent variables, three of which take on nonzero values for two room
uses, i.e. x-j = 1 for either general or clerical offices. For the purposes
of this report, the seven independent room use types were retained.
Although previous surveys (8) and the data in Figures 23-26 suggest that the
fire load and live load are related to the area of a room, the regression
analysis using room use and room area did not indicate that area had a signif-
icant effect. The results obtained including both room use and area were as
fol lows
:
115
Mean Live Load (psf) = 9.5x^ + 10.7x2
+ 4.4x, + 6.1x, + 26.0X1- + 16. Ix^3 4 5 p 6
+ 26.8X7 " 0-00134 Area (ft ) (3a)
Mean Total Fire Load (psf) = 7.7x^ + 6.9X2 + 4.7x2
+ 5.5x. + 17.3Xc + 12.9Xc4 b ° ?
+ 25.0X7 " 0-00098 Area (ft )^3^^^
Note that the form used for Equations 3 is somewhat different from that usedfor Equation 1, i.e. no constant term. For general offices of different size,
2the live load from Equations 3 would be: Area = 50 ft , Live Load = 9.4 psf;
Area = 100 ft^, Live Load = 9.4 psf; Area = 150 ft^, Live Load = 9.3 psf;
Area = 300 ft^, Live Load = 9.1 psf; Area = 500 ft^, Live Load =8.9 psf.
This decrease in load with increase in area is considerably less than thatindicated in Figures 23 through 25. Similar results occur for the otherroom uses.
The preceding analysis suggests that room use and room area may be correlated,i.e. file rooms may normally be small rooms, conference rooms and lobbieslarge rooms, etc. A regression analysis was performed in which the coefficientfor the area term in Equations 3 was related to the room use. The results
obtained for this case were as follows:
Mean Live Load (psf) = (9.5 - 0.00135A^)x^ + (10.7 - 0.00123A2)x2
+ (4.7 - 0.00216A3)X3 + (6.4 - 0.002^AI\^)x^
+ (26.3 - 0.00179Ag)Xg + (16.0 - 0.00067Ag)Xg
+ (22.4 - 0.01509A7)X7^^^j
Mean Total Fire Load (psf) = (7.8 - 0.00129)x^ + (6.8 - 0.000085)x2
+ (5.2 - 0.00271)X3 + (6.1 - 0.0028)x4
+ (17.0 - 0.00038)X5 + (13.0 - 0.00179)Xg
+ (20.1 + 0.01680)X7
The results in Equations 4 indicate that the decrease in load with increasing
area is different for the various room uses. The decrease is largest for
lobbies and the load in libraries actually increases with increase in area.
Results from the regression analysis suggest that the variation of load with
area is related to room use. The trend observed in Figures 23 through 26 and
in previous surveys may be due to the fact that the smaller heavier rooms are
primarily one type of room (e.g. file, storage) and the larger lighter rooms
are another type. The influence of area on load magnitude requires further
study. Prior to developing live load reduction factors for design purposes,
it may be important to determine the degree to which the position of various
room types is correlated. One would expect, for example, that the reduction
factor for areas comprised primarily of file rooms would be different from
that for areas comprised of general offices.
116
3.9 Evaluation of Load Models
In order to evaluate the load models, the majority of rooms were surveyed inBuildings 14, 24, and 27. These three buildings were selected prior toderiving the load models in Section 3.8. Their characteristics (height,age, geographic location, occupancy) were similar to the other 20 buildingsused to develop the load models. As indicated in Section 3.3, only 25percent of the rooms for each of these three buildings was combined with thedata for the other buildings to develop the load models in Section 3.8. Theevaluation procedure involved using the first load model (Equations 1 and 2
in Section 3.8) to calculate the loads in all the rooms in these threebuildings and then comparing these loads with the survey values. This wascarried out using the BUILDER computer program discussed in Reference 6.
The results of the evaluation are given in Table 38 and Figures 37 through 41.
Differences between the measured (surveyed) and calculated loads for each roomin the three buildings are summarized in Table 38 separately for each buildingand for all the rooms. For Buildings 14 and 27 the mean value of the dif-ference was negative, i.e. the measured loads were less than the calculatedvalues. For Building 24, the reverse was true. For the 863 rooms in thethree buildings the mean difference was less than 1 psf for live load. Onewould expect this difference to approach zero as the number of buildingsconsidered increased.
The standard deviation for the difference between measured and calculated loadsfor room loads was approximately the same as that for the load models in
Section 3.8. This is also as expected since the variation in loads betweenrooms in the three buildings was probably similar to that for the buildingsused to derive the load models.
Histograms illustrating the differences between measured and calculated loads
for the three buildings are given in Figures 37 through 40.
Differences between the measured and calculated values for the total load on
each floor are also summarized in Table 38. Only loads for the offices sur-
veyed were considered in obtaining these floe loads. Loads in unsurveyedrooms, corridors, stairways, etc. were not coiisic'^red. The differences are ex-
pressed in absolute terms (kips) and also as a percent difference. The histogram
for the oercentage difference for all the flor s in th'^ three buildings is
given in Figure 41. ''is in the case of room loads, t!ie measured floor loads for
Buildings 14 and 27 were less than calculated (mean percent difference negative)
and those for Building 24 were greater. For all 39 floors in the three buildings,
the Hiean percent difference is 40 percent. The coefficient of variation for
the floor live loads (59/40 = 1.48) is greater than that for the load model
(Equation 1, Section 3.8).
Differences between the measured and calculated values for the total load in
each building are also given in Table 38. As with room and floor loads, the
measured loads were less than calculated for Buildings 14 and 27. The mean
percent difference for all three buildings was 8 percent.
117
CO OO "— —
-
<T\ '—
-
• LD • o • o 1 1 1
"O > CO LO O CSJ oo LO LO 1 1 11— CO
4-> CD C\J
—
CO —" OO •—
^
LO "
—
C/^ OO
LD CO —
•
I . ^ ^ 00 -"^ o f—c: * • CO * CTt • LO • o • CTi • ,
T3 03 r— LO C\J o LD LO o OO CO CO CO(13 CD 1 C\J '
1 LO i O CO 00 OJ 1
O OO OO 1
1 1 1 1 1 1 1 1 1—
-
1
CD>
1 CO C\J CO LO ^ CTi CO -—
^
CTi ^ "—
^
"O • • LO • CO 1 1 1 • COro X LO CO r*^ CO LO CO 1 1 1 CO COO (O LO CO CO LO CO —" LO "
—
•' 00 —-' LO —
^
>
—
1 e: OO
"OCDO +->
CO CO CO CO '—
^
r— OO -—
^
CO .—
-
O "—o * • oo • CM . LO • OO • o*i
1 3 c: o C\J CSJ LO 1
—
CO o> ^ 1 1 1 OO(_) C\J CSJ CO 1
—
1 ' CO 1
—
1 1 1 CO 1
o 2; t 1 OO —UJ n3 1 1 1 1 I 1 1
q;ZD
1
=rLlJ "O o o -— O — *^ -—
•
CO •-—
^
CO —«>
1 1 1 • COo > LO O 'd" CO ' CO 1
—
CO (y> 1 1 1 r— ^1
1-—^ oo r-*- OO "
—
CO '
—
"
c/^ Q OO<c "O
Q s_
LlJ 131— CO o LO cr> -
—
'—
^
LO -—
^
f— - ^ -
—
r— —
^
OO -—
>
00 -
—
sC 03 13 * • • r— ' LO • O • J— • r— • • LO • o1 CD O 03 CO CO n— LO C\J r— OO kO LO CO r*^ OO LO LO CO OO
Z3 1CD 1 1
«>
—
OO 1
—
1 OO 1 1 ^— 1
O1 CD 1 1 1 I 1 ^
1 1 1 1
=1 S-o •f—
2:U-
UJ 1
—
CO c\j —
-
O '— OO — OJ '
—
f— " ^
UJ to • • CO • CO • 00 • CO 1 i 1
3 +J X LO CO 1
—
O CO CTi CO CTi CO 1 1 1 OO1
—
o to CO oo oo ' " CO —
'
LO —
^
LO —
^
UJ h- IECO
oCTt -—
^
^ -—
•
«^ —
^
CTi " OO "—
^
t—
*
• • • LO • LO . CTi • LO LOq; CO CO CO LO <vj- O 1
—
CO LO LO 1 1 t LO LO=£ r— C\J r— 1
—
'
CO OO 1—1 1 1 1
1 1 1 CO "
1 1 1 1 1"
1'
1o
COCO CO CO <o LO
o J2 CTi LO 1— p— CO
UJ z o C\J r— 00_JCQeCt—
C\J OO OOoic•n-
T3 O'
—
CM oo OJ oo OOCM OO OO
CQ
£^ c:
-a E -o M- O -o CO -o 00
ro O 03 co o n3 "O fO CLO O O O o_l _J U- —I _1
=3CQ
CDLJ
O)S-
-o
+->
O)LO LJOJ
Q.
OJ CD
03Q.
o
LO LOOJ O)
03
o"DOJ(/)
03JH
0)S-
03
118
FREQUENCY -%30
-25
20
-15
ROOM LOADS- BUILDING 14
NO, OBS. = 291
MAX. VAL. - 52.3 PSF
MIN. VAL = -19.8 PSF
MEAN = -1.6 PSF
STD. DEV. - 8.3 PSF
-1 i_n-20 -15 -10 -5 0 5 10 15 20 25 30
MEASURED LIVE LOAD (PSF) - CALCUL;\TED LIVE LOAD (PSF)
Figure 37 - Difference Between Measured and Calculated
Room Live Loads--Building 14
119
FREQUENCY -%
20T
15-
10-
ROOM LOADS
- BUILDING 24
NO. DBS. = 151
MAX. VAL = 35.7 PSF
MIN. VAL = -10.1 PSF
MEAN = 5.5 PSF
STD. DEV. = 7.4 PSF
-10 0 10 15 20 25 30 35
MEASURED LIVE LOAD (PSF) - CALCULATED LIVE LOAD (PSF)
Figure 38 - Difference Between Measured and CalculatedRoom Live Loads--Bui Iding 24
120
FREQUENCY-%
30
-25
+ 20
-15
ROOM LOADS- BUILDING 27
NO. DBS. = 421
MAX. VAL. = 38.2 PSF
MIN. VAL. = -22.3 PSF
MEAN = -2.8 PSF
STD. DEV. = 5.7 PSF
-15 -10 -5 0 5 10
MEASURED LIVE LOAD (PSF) - CALCULATED LIVE LOAD (PSF)
Figure 39 - Difference Between Measured and CalculatedRoom Live Loads--Bui Iding 27
121
FREQUENCY -%t25
- 20
15
-15 -10 -5
ROOM LOADS- BUILDINGS 14, 24, 27
NO. DBS. = 863
MAX. VAL. = 52.3 PSF
MIN. VAL = -22.3 PSF
MEAN = -0.9 PSF
STD. DEV. = 7.6 PSF
5 10
MEASURED LIVE LOAD (PSF) - CALCULATED LIVE LOAD (PSF)
Figure 40 - Difference Between Measured and CalculatedRoom Live Loads--Bui Idings 14, 24, and 27
122
FREQUENCY -%t40
FLOOR LOADS- BUILDINGS 14, 24, 27
NO. DBS. = 39
MAX. VAL. = 49%
MIN. VAL. = -142%
MEAN = -40%
STD. DEV. = 59%
30
-200 -150 -100
MEASURED FLOOR LOAD (LB)
-50 0 50
CALCULATED FLOOR LOAD (LB)
MEASURED FLOOR LOAD (LB)
XlOO
Figure 41 - Difference Between Measured and Calculated
Floor Live Loads--Buildings 14, 24, and 27
123
The comparison indicated that the loads in two of the three buildings wereless than the calculated loads and greater than the calculated values in onebuilding. One would expect similar results if three other buildings fromthe survey sample were used for comparison with the models. As the numberof buildings included in the comparison increases, the mean value for thedifference between measured and calculated loads should approach zero. In
view of the inherent variability in loads from room to room, however, onewould expect the standard deviation for this difference to be approximatelythe same as that for the load models in Section 3.8. Similar results should
occur for comparisons with other buildings not included in the survey if
the loads in the 23 buildings used to derive the load models are represen-tative of those in the population of office buildings.
124
4. SUMMARY AND CONCLUSIONS
This survey was designed to identify the factors such as building height,building age, geographic location, etc. which affect the magnitude of fireloads and live loads in office buildings. A special survey technique anddata processing procedures were developed to economically and efficientlycollect data from a large number of buildings. Twenty-three office buildingsboth Federal and private, from thoughout the United States were surveyed.Buildings ranging in height from two stories to forty-nine stories wereincluded. The total number of rooms surveyed was 2433, of which 74 percentwere general and clerical offices. The complete record of all the originalfield survey data was retained on microfilm and will be available forcontinuing studies and analysis.
Survey results were presented evaluating the influence of building charac-teristics (height, age, location), occupant characteristics (firm type), androom characteristics (room size, room use) on the magnitude of fire loads andlive loads. The data were utilized to develop mathematical models for pre-dicting load magnitudes in office buildings. Recommendations were also developedfor additional research on loads in office buildings based on results obtainedfrom the survey.
Based on the survey results presented herein, the following conclusions wereobtained:
1. The measurement error associated with the inventorytechnique used in this survey was approximately 10
percent. This represents a relatively small fractionof the variability of live loads from room to room in
office buildings.
2. The magnitude of the loads in rooms in office buildings
is not affected by the geographic location of the building,
building height, or building age.
3. There does not appear to be any significant difference
between loads in government and private office buildings.
4. The magnitude of room fire loads and live loads is
related to the use of the room. Libraries, file
rooms, and storage rooms were the most heavily
loaded. In general, the mean room load decreases
as the area of the room increases although room use
and room area may be correlated. Further study is
required to establish the influence of area on load
magnitude.
5. The variation of load with time requires further study.
Although the mean load for the NBS Administration
Building increased over a period of seven years, there
was no clear indication of such a trend based on a
comparison of mean load versus occupancy duration for
the other buildings surveyed.
125
6. There is a definite tendency for loads in offices to beconcentrated around the perimeter of the room.
7. Mean values of occupancy duration for government andprivate firms were 8.4 years and 7.9 years respectively.This difference is not statistically significant.
8. The interior finish fire load in a room ranged from
1.0 psf to 1,9 psf. The contribution of interior finishto the total fire load ranged from less than five percentto as high as fifty percent depending on room use.
9. The mean number of discrete concentrated floor loads in
the rooms surveyed was eighteen.
10. The 99 percent fractile for the heaviest load in a roomis quite close to the value currently used for designingoffice buildings.
n. In the majority of offices surveyed, between 20 and 40
percent of the floor area was occupied by furniture and
equi pment.
126
5. Research Recommendations
Prior to undertaking any additional survey work or implementing theresearch results obtained from this study, it is recommended that additionalanalysis be done using the available data. The data have been summarizedherein in terms of means, standard deviations and range. Further analysisshould be undertaken to estimate tolerance limits and fractile values usingthe means and standard deviations presented and assumptions regarding theform of the distributions. The necessity for improving the accuracy of theload models should be established and the implications of the survey resultsrelative to existing design requirements for buildings should be examined.The survey data should also be used to assess design load magnitudes, liveload reduction factors, fire endurance requirements, etc. currently in use.A detailed plan for this activity should be prepared. As a minimum thiseffort should include:
1. Determine horizontal and vertical correlation ofloads and room locations.
2. Establish the relationship between load magnitudeand loaded area.
3. Determine load magnitudes for typical structuralbay sizes and configurations.
4. Establish the characteristics of heavily loadedrooms.
The relationship between load magnitude and area and horizontal and verticalcorrelation of loads are particularly important since structural designrequires design loads for structural bays rather than room loads and a
knowledge of the variation of load through the height of the building. If
room boundaries correspond to the framing system layout, the room data
obtained in this survey can be used directly to establish structural bay
loads. The data may also be used to obtain values for the more generalsituation where room boundaries and the framing system are not correlated.Using the floor plan layout for the buildings surveyed (6) and the load
models developed in Section 3.8, loads could be calculated for the various
rooms. After assuming loads for areas not included in the model (lavatories,
corridors, etc.), the notional bay overlay concept used by Mitchell or an
overlay of the exact framing system could then be used. An alternateapproach would be to use Monte Carlo simulation techniques to construct
floor plan layouts and framing system schemes, calculate the loads in the
rooms using the load models in Section 3.8 and then calculate loads on
the structural system using either the concept of tributary area or influ-
ence area (15) . As part of this analysis, horizontal and vertical correlation
of loads would also be determined.
For each room surveyed, the computer program used for the data processing
computed a variety of important quantities (6). Simulation studies similar
to those in the appendix of this report could be carried out using these
data. For example, the effect of enclosing all combustibles, such as paper
and books, in metal containers could be evaluated by comparing the total
fire loads presented herein with derated values obtained from such a study.
The effect of changing the composition of office contents (replacing wood
furniture by metal, etc.) could also be studied. Limited Monte Carlo simula-
tion studies of this type to determine fire severity were carried out byCoward using existing survey data (16).
127
If additional survey work is done, the surveys should be carried out in
Government buildings. This would reduce the problems of obtaining surveypermission encountered in this survey. Based on results presented in
Section 3.8, loads in Government and private office buildings do not differsignificantly and the data obtained would be generally applicable. Also,since the geographic location of the building does not affect load magni-tude, the survey work could be concentrated in one locality to minimizetravel expenses for the survey crews. Data collected in the first phaseshould be used to plan these additional surveys. Correlations between the
locations of rooms by room-use should be determined to establish a samplingplan for gathering data on horizontal and vertical correlation of loads.
The characteristics of heavily loaded rooms could be determined to establisha sampling procedure to obtain data to better define the "tail" of the
frequency distribution for load magnitude.
The survey forms, data collection procedures, and computer programs for dataprocessing developed as part of this project could also be used to monitorthe variation of loads with time. Periodically resurveying a particularbuilding would indicate the types of load changes taking place and permitextrapolation for future requirements relative to live load and fire load
capacity. Data could also be collected for use in planning renovation and
rehabilitation work for existing buildings.
128
6. ACKNOWLEDGMENTS
The work reported herein was conducted by the National Bureau of Standardsfor the National Academy of Sciences. The survey project was sponsored bythe General Services Administration. Special recognition is due GSA forthe initiative and foresight demonstrated by their sponsorship of thiswork. The cooperation and advice of the project advisory committee estab-lished by the National Academy of Sciences: Charles Schaffner, Chairman,Syska and Hennessey Consulting Engineers; Richard Bletzacker, Ohio StateUniversity; William Christian, Underwriters Laboratory; Dr. Howard Emmons,Harvard University; Dr. T. T. Lie, National Research Council (Canada);Lawrence Seigel, United States Steel Corporation; and James Smith, BuildingResearch Advisory Board, is also acknowledged.
A report prepared for NBS by Professor C. Allin Cornell, MassachusettsInstitute of Technology, formed the basis for preliminary planning ofthe survey. The following NBS staff contributed to the project: NewtonBreese and Daniel Gross, Center for Fire Research; Leighton Greenough andRobert McCabe, Center for Consumer Product Technology; William Greene and
Bruce Ellingwood, Structures Section; and Dr. Joan Rosenblatt, AppliedMathematics Division. Dr. Rosenblatt's contribution in connection withvarious aspects of the survey design and data analysis is particularlyacknowledged. Dr. Rosenblatt and Ms. Delmas Maxwell, from the StatisticalEngineering Section, carried out the analysis of the inventory surveytechnique included in Section 3.2. Irwin Benjamin, Center for Fire Research,
assisted in obtaining survey permission for a number of buildings. Samuel
Kramer, Acting Deputy Director, Center for Building Technology, provided
continual support and administrative assistance throughout the course of the
work. Professor James Yao, Purdue University, also contributed to the
initial phase of the project. Special acknowledgement is due Ms. Leslie
Suddueth for the care exercised in typing the report.
The field survey was carried out by Mathis Associates, Fresno, California,
under the supervision of NBS staff. Professional staff from the J. H. Wiggins
Co., Redondo Beach, California, developed the data reduction and analysis
programs and participated in the analysis of the survey data. The assis-
tance of Larry Lee, Joseph Hirschberg, and Jon Collins is particularly
acknowledged. The Monte Carlo analysis of live load effects in the
Appendix was carried out by Professor Gary Hart, University of California,
Los Angeles, under the direction of the author. The assistance of Erne
Wilkins, FOSDIC Branch, Engineering Division of the Bureau of the Census, was
helpful in connection with the data processing.
The Building Owners and Managers Association cooperated in the project and
Robert Wiggs, of BOMA, assisted in securing permission to survey a number of
the buildings in the private sector. Survey permission for the government
buildings was obtained through the Public Buildings Service, GSA.
129
7. REFERENCES
1. America Burning , The Report of the National Commission on FirePrevention and Control, May 4, 1973.
2. Heany*, Alexander C, "A Reliability-Based Study Concerning Live Loadsand Codified Structural Design," Thesis presented to the Universityof Waterloo, Waterloo, Ontario, Canada, 1971, in partial fulfillmentof the requirements for the degree of Doctor of Philosophy.
3. Ingberg, S. H.; Dunham, J. W. ; Thompson, J. P., "Combustible Contentsin Buildings," Building Materials and Structures Report 149, NationalBureau of Standards, Washington, DC, 1957.
4. Bryson, J. 0.; Gross, D., "Techniques for the Survey and Evaluationof Live Floor Loads and Fire Loads in Modern Office Buildings," NBSBuilding Science Series 16, December 1967.
5. Culver, Charles; Kushner, Jill, "A Program for Survey of Fire Loadsand Live Loads in Office Buildings," NBS Technical Note 858, May1 975.
6. McCabe, Robert; Culver, Charles; Lee, Larry T.; Hirschberg, Joseph G.,
"Data Processing and Data Analysis Procedures for Fire Load and LiveLoad Survey Program," NBSIR 76-982, December 1975.
7. Natrella, Mary G., Experimental Statistics , Handbook 91, NationalBureau of Standards, U.S. Department of Commerce, 1962.
8. Mitchell, G. R. ; Woodgate, R. W., "Floor Loadings in Office Buildings -
The Results of a Survey," Current Paper 3/71, Building Research Station,England, January 1971
.
9. Dixon, Wilfrid J.; Massey, Frank J. Jr., Introduction to StatisticalAnalysis , Third Edition, McGraw-Hill, 1969.
10. Conover, W. J., Practical Nonparametric Statistics , Wiley, 1971.
11. Standard Industrial Classification Manual , U.S. Bureau of the Budget,Office of Statistical Standards, Washington, DC, 1967.
12. Benjamin, J. R. ; Cornell, C. A., Probability, Statistics, and Decisionfor CI v1 1 Engineers , McGraw-Hill Book Company, New York, 1970.
13. Lie, T. T., Fire and Buildings , Applied Science Publishers Ltd., London,
1972.
130
14. Lie, T. T.; Stanzak, W. W., "Structural Steel and Fire-More RealisticAnalysis," ASCE National Structural Engineering Meeting, April 22-26,
1974, Cincinnati, Ohio, Preprint 2256.
15. McGuire, Robin K. ; Cornell, C. Allin, "Live Load Effects in OfficeBuildings," Journal of the Structural Division, ASCE, Vol. 100, No. ST 7,
Proc. Paper 10660, July 1974, pp. 1351-1366.
16. Coward, Sara K. D. , "A Simulation Method for Estimating the Distributionof Fire Severities in Office Rooms," Current Paper 31/75, BuildingResearch Establishment, Fire Research Station, Borehamwood, England.
17. "Fire Resistance Classifications of Building Constructions," BuildingMaterials and Structures Report 92, National Bureau of Standards,Washington, D.C., October 1972.
131
8. APPENDIX
STRUCTURAL INFLUENCEOF
LIVE LOAD LOCATIONS
In order to simplify the data collection procedure in this survey, onlyapproximate locations were obtained for the loads in the rooms, i.e. loadswere recorded as to whether they were within two feet from the walls. Ananalysis of the effects of fire load location on fire severity and heat trans-ferred to the bounding surfaces (floor, walls, ceiling) indicated that thisapproximate scheme was satisfactory (4). Studies of the influence of thisprocedure on the computation of forces in the structural system of a buildingindicated that the accuracy used to locate the loads in a room has an effecton the structural member forces computed from these loads (4). These studieswere limited, however, and did not consider the full range of cases encounteredin actual buildings. The analysis presented in this appendix is more generaland is intended to evaluate the adequacy of the survey procedure from the stand-point of live load effects.
PROBLEM FORMULATION
Live loads in offices due to furniture, equipment, etc., will be arranged in
various ways depending upon the configuration of the room, occupant preferenceand the nature of the work being conducted. The exact location of these itemsis of interest in planning work flow, movement of the occupants and other con-siderations relative to efficient space utilization. For structural designpurposes, however, load locations are only important with respect to their effecton the structural system. The most appropriate way of evaluating these effectsis through the use of influence surfaces (3, 5).
Recognizing that precise locations of office loads may not be required for
structural design purposes, the approximate load location scheme shown in FigureAl was adopted for the 1967 NBS load survey. Each office was subdivided into
the nine sectors shown and the load for each item in the room assigned to oneof the nine sectors. The dimensions of the strips were consistent with the
definitions used in designing two-way flat slabs. It should be emphasized that
the rationale used to establish this sector configuration assumes that the
boundaries of the room correspond to the column lines for the structural system.
This correlation has not been established and in many cases rooms in officebuildings are smaller than structural bays. In other cases such as office land-
scaping, the rooms are larger than one structural bay.
Corotis' study of the adequacy of the sector arrangement in Figure Al (2) and
Yao's study of other sector arrangements (4) were limited to the case in which
the room and structural bay were equal in size. For the study reported herein,
a Monte Carlo simulation was carried out to evaluate the influence of various
approximate load location schemes. The procedure followed was similar to that
used by Corotis. Using influence surfaces, the forces and moments in the columns
132
[-»b/4»j h»b/4-H
Figure Al - Approximate Load Location Scheme
(1967 NBS Survey)
133
of the vertical load carrying system were determined using both the exactload locations and approximate locations. Whereas Corotis used only the surveydata obtained from one building (2), this study includes a variety of parameters
The room and bay configurations adopted are shown in Figure A2. The fourcolumns represent a structural bay. Forces and moments in all cases were com-puted for column 1. Two cases were considered for the room location. For
Case I one corner of the room coincided with a corner of the structural bay.For Case II the room was located in the center of the bay. In each case theroom dimensions were taken as a percentage of the bay dimensions. The limitingcase involved a room equal in size to the structural bay. The case of a roomlarger than a structural bay was not considered.
Four different schemes were used for subdividing a room. These are shown in
Figure A3 and will be referred to as the one-sector, two-sector, five-sector,and nine-sector model. The nine-sector model is the one used in the 1967NBS survey and the two-sector model the one adopted in the current survey,i.e. in the current survey load locations are only recorded as either beingwithin 2 feet of the wall or greater than 2 feet from the wall.
The number of loads, load magnitude, and the location of the loads in a roomwere varied over a wide range. This was done in order to investigate the
significance of various load arrangements as opposed to using limited surveydata. The number of loads was treated as a random variable with a normal pro-bability density function. Most previous surveys have not reported values for
this quantity. Data from the 1967 NBS survey indicated an average of nine
loads per room and Corotis' studies were based on this value. Only loads
corresponding to heavy furniture items (desks, tables, etc.) were consideredand loads due to chairs, wastebaskets , etc. were neglected. The majority of
2 2rooms in that survey, however, were between 150 feet and 200 feet . For
larger rooms one would expect a larger number of loads. The current surveyindicated that a typical room contained more than nine discrete loads. For
the case of a room equal in size to a structural bay a mean value of sixteenloads was used. The case of thirty-two loads was also considered to determine
the effect of this parameter. For a smaller room with an area equal to approxi-
mately one-half the area of the structural bay, mean values of eight and sixteenloads were considered. Since the current survey data indicated considerablescatter, a coefficient of variation of 50 percent was used.
Load magnitude was also treated as a random variable. The 1967 NBS survey data
indicated that the load per unit area on the individual sectors could be repre-
sented by a series of gamma probability distributions (2). The probabilitydistribution of the load per unit area for a complete room, however, was approxi
mately normal. Mitchell's data (6) indicated a similar trend. A normal
distribution was used, therefore, for the load magnitude in this study. A log
normal distribution was also considered to evaluate the effect of this parameter
Data on individual load magnitudes were not given in previous studies. Corotis
used a mean value of 245 lb. and a standard deviation of 80 lb. In this study
134
1 4i
CASE II
Figure A2 - Room and Bay Configurations
135
T 2 ft
T
h« b HONE SECTOR MODEL
1b
TWO SECTOR MOOEL
-»^3 ft^ t
1
i
I
1
f
3 ft
1
-« b »-
FIVE SECTOR MOOEL
b/4 b/4 \* t
~l\ a/4
a
li
t
a/4
b -HNINE SECTOR MODEL
Figure A3 - Sector Models Studied
136
a mean va''ue of 100 lb. was used since all the items in a room were con-sidered. :>ince the data showed considerable scatter with loads as low as5-10 lb. (wastebaskets) and as high as several hundred pounds for heavyfurniture, a coefficient of variation of 50 percent was used. A value of150 percent was also used for the coefficient of variation.
The location of the loads in the room was also treated as a random variable.A uniform distribution of loads throughout the room was used with the expectedvalue of the number of loads in each sector being the same. This correspondedto the case studied by Corotis (2). Since the current survey indicated a
tendency for discrete loads to be located around the perimeter of the room,particularly for smaller rooms, a second case with 70 percent of the discreteloads around the perimeter and 30 percent in the center portion of the roomwas also studied. The placement of loads was random and a uniform distribu-tion throughout each portion was used. Since the discrete loads used representthe load at the center of gravity of the furniture item, a constraint wasrequired to represent the practical case with a finite spacing between items.
In all cases, the location of each load rela*'"ve to the other loads and the
boundaries of the room was constrained to bt -eater than two feet. Thisminimum value was based on the "average" size of office furniture.
The effects of the variables noted on the axial force and moments for Column 1
in Figure A2 were studied using influence surfaces. The forces were computed
using the influence ordinate for each load location and also using the averageinfluence ordinate for the various sectors for all loads in that sector. The
same approximate influence surfaces as used by Corotis (3) and Peir (7) wereused in this study. The difference between the forces computed using the exact
and approximate locations provides an indication of the "error" associated with
using subdivisions for a room as opposed to exact load locations (3). Since
the ratio of these forces or the percent difference provides a better indication
of the relative error than simply the difference, results presented in the next
section are expressed in this form.
A special computer program was written to carry out this study. The program was
written to allow considerable flexibility in order to investigate a variety of
combinations of room and bay proportions, number of loads, load magnitude, and
load location.
137
NUMERICAL RESULTS
The computer program was first used to solve Corotis' and compare the resultswith those from the closed form solution. This comparison is given in Table 1
for column axial load and column moments. For this problem the room was equalin size to the bay and there were exactly nine loads. The mean value andcoefficient of variation were the same as those used by Corotis (2). A normaldistribution was assumed for load magnitude in the Monte Carlo solution. Theclosed form solution of Corotis was independent of this parameter and utilizedonly the mean and standard deviation. A uniform probability of occurrence wasused for the position of the nine loads throughout the room. The ratio of themean column load computed using the nine-sector model and the exact load loca-tion is given. Since no attempt was made to determine the probability densityfunction for this ratio, the interval (X-j, X^) for which the probability that
the error in the computed column load due to using sectors is less than somevalue a, P[X-j <_ P^/P^ 1 X^] = 1 - a, was not determined. To provide a qualita-
tive estimate for other than the mean error, the column load ratio using the
exact and approximate load locations was computed for one, two and three standarddeviations.
Referring to Table 1, the ratio for the mean column load for the two solutionsdiffers by only one percent. The difference for the moment ratio is slightlyhigher. The two moment ratios for the Monte Carlo solution correspond to the
moments about the x and y axes, respectively. Only the moment about the y axiswas computed by Corotis. As the number of standard deviations increases, the
difference between the column loads obtained using sectors versus the exactload location increases for both solutions. The differences between the two
solutions also increases with the maximum difference being 12 percent for the
moment about the x axis at three standard deviations.
The influence of the number and distribution of the loads in the room on the
column load and moment ratios are presented in Table 2. The single ratio givenfor moments corresponds to the worst case, i.e. the lowest ratio. Sixteen and
thirty-two loads were used with a uniform probability for the load location.
Since the survey results indicated that the furniture in rooms is usuallylocated around the perimeter, the case with seventy percent of the loads
around the perimeter and the remaining thirty percent in the center portion
was also studied. For all the cases in Table 2, the error in the mean columnload is less than one percent. The influence of the number of sectors does
affect the mean column moment but the differences are not significant from the
practical standpoint. For axial load, the results obtained for one and two
sectors were the same. The error increases with the number of standard devia-
tions. For sixteen loads the ratio decreases from 0.871 at one standard deviationto 0.729 at three standard deviations. As expected, the error decreases as the
number of sectors is increased. The maximum error for the two-sector model at
three standard deviations is 27 percent and 5 percent for the nine-sector model.
Comparing the results for 16 and 32 loads indicates that the error decreases as
the number of loads increases.
138
oz<c
o_l
oTEz COo COs: z -—
-
oa: o >iO >—< "3 II
Li- 1— mOO _I o1— o +->
—1 OOZD >—
q; o o- LnU- UJ
Ll.O Q ELU O IIZ OO OO O Qi E
OO _I1—1 O
c:< o+jOJ3
o S--l->
II to
>ES-o n3M- E
II S-c o
E =5 Z
>>
1
ca c too S-
M- I/) oo -o p
03 uo O OJ•r— _l -!-> 00-t->
m <+-
cc O to CJ) OfO
+-> s_ Q 2: S-<u a;
<u J3 -O T3 j2Q. E ro ra Eto :3 O OcC z: _J _l
to toro CO
CO c\j Ln+ + cn to C\J
00 cri
OO LU os: 2: o o
to toCM CO Ln
00 CO CO+ + CTv CO CTl
+-> • •
t/0 LU o o o(U s;EOs:
cE to to ^— un CM
CTl I— Ln+ + <Tl cri cn
oo OO LU O <~> os: s:
1— oo COo CTi cri
o o
CO CO OO unCO
+ + cyi
00 LiJ o oCL. Q.
to toeg CM tn CO
CDO Ln_|_
•o OO o oQ. D.
o1
n3•r- to to o 00X<t + + cn CTv
OO LU o oa. Q_
o ^—OO UJ o o
Q- Q- •
(
E oo cU_ O CM fO oo T-o +J . +->
0) 3 t(_ 0) =5to 1— 0) -l-> 1—o o d; c o1— OO^ O OOo
139
00
o
LjJ >,
O r-
LU :3
OO
<
OII
oo
4->
>^
CQ
4-O O)
T3O =s
+->
+->
roca cn
+->
o0) oQ. toCO oCC 1
o
O
X
1/1
CM
+
D.
OO UQ. Q.
I/)
S-o
O M- -MZOOO)OO
T3 3to J3O -1-
_1 S--!->
CO
-aO 4- fO2: o o
OJ ro CTitn CO o COr-~~ 00 CO
0000
CD r— COo CO 00 COCO r~-. CO CO
0000
IT) r— 00 ^CO en r—CO CO 00 CTi
0000c\j CDI— un ss- uoO CTi CTi CTl
1—000
CTi CTi O COoj CM ro «=J-
r-^ CO CTi
0000
CD CD ^ Cri
CO 00 CD LDr~. 00 CTi
0000
1— I— LD CD
CO CO cn CTi
0000CO CO CMO O CTi oo o cTi o
EoC|-
LD CM r-~ro o c\i
CO CO 00 CTi
0000
Ol CM 00 ^-^i- CTi 00
CO CO 00 cTi
0000
^ o cri 00ro cn 1—cTi CO en cTi
0000CTi ^ CM unO LD LD LDo cTi cri cn
—000
CO CO CM oCM CM r— CO00 00 CTi cr^
0000
ro ro 00 <^r-^ ro 00
00 CO en CTi
0000
r— I— .— CTlro ro CD 00CTl CTl CTl CTi
0000O O CTi CDI— I— CJ^ CTlo o cri cri
I— CM LD cyi
o
ZD
CMro
o CD oCTi LD ^
CTi r-^ CO en
0000
O I— CTiCD CM CO LDO CO 00 C3^
r— O O O
O CD CTi
<^ CD 1— COI— CO CTv CTi
1—000CD ro ro COCD 00 COCM cyi cn or— O O .—
^J- «^ O CMro ro COCO 00 CO CTi
0000
I— I— ^ enr-. en CO00 00 CO CTl
0000
I— COCM CM roCTl CTv CTl Cn
0000I— I— CM LDCM CM CTi cno o cn cTi
I— t— o o
S-cu+J
c: EO S-O S- O)
O LO ro CM^ cn CDCTi r-~ CO cn
0000
LD ^ cnr-- o r— 1^o cx) cn cn
>— o o o
CO LD LDCM O1— 00 CTl o
CM ro LD roI— CM O LDCM cn o or— O 1— .—
CD CD CD I—ro ro cn CD00 CO CO cn
0000
00 CO r-^ COCO CO 1— COCO CO cn cn
0000
=d- 00 cnI— I— r-^cn cn cn cn
0000
o o 00cn cn cn cncn cn cn <n
0000
I— CM LD cn
S-O)+->
-O O)c E
&S O S-o S- OJn3 CL
140
The load distribution also affects the error. For 16 loads the error is
less for the case of 70 percent of the load around the perimeter than for a
uniform distribution. The decrease due to this effect is less significantfor 32 loads.
For column moments in Table 2, the error for the mean is greater than for axialloads. Unlike the case for axial load, the results for one and two sectorsare different. The mean is also more sensitive to the number of sectors. Forone, two and three standard deviations, however, the number of sectors is lesssignificant. For example, with 16 loads and a uniform distribution the axialload ratio at three standard deviations changed from 0.729 for one sector to0.948 for nine sectors (30 percent) while the moment ratio only changed by 16percent from 0.752 to 0.869. As with axial load, the error increases with thenumber of standard deviations. Note that in some cases, however, the ratiois greater than one indicating that the moments obtained using sectors wouldbe greater than those obtained from the exact load location. As with axialload, the errors decrease for the case of 70 percent of the loads around theperimeter.
The influence of room size is indicated in Table 3. For this case the roomdimensions were 75 percent of the bay dimensions, i.e. the room area was 56
percent of the bay area. The room was located in the corner of the bay,
Figure A2-Case I. This corresponds more closely to the situation in officebuildings since the mean room area for the offices surveyed was approximately
2 2200 ft and common structural bay sizes are around 400-600 ft . The load dis-tribution and magnitude were the same as those used in Table 2. The numberof loads was reduced, however, for this smaller room since the survey data
indicated the mean number of loads in a room this size was 18. The resultsin Table 3 are similar to those in Table 2 and the same trends occur. The
errors for this case are much less, however. For 16 loads and a uniform load
distribution, the axial load ratio for one sector at three standard deviationswas 0.729 in Table 2. This ratio increased to 0.878 in Table 3. The errorsoccurring as a result of using sectors is thus directly related to the size of
the room relative to the structural bay. For the case encountered in this sur-
vey (16 loads, 70% around perimeter, room area bay area/2), the maximum axial
load and moment error for the two-sector model is 7 percent. This error is
negligible from the practical point of view when one considers inherent measure-ment errors in any survey technique and the fact that furniture loads are not
single concentrated loads.
The influence of room location is shown by comparing Table 3 to Table 4. The
parameters used were the same as those for Table 3 except that the room is
located in the center of the structural bay. The error associated with using
sectors is greater in this case than for the room in the corner of the bay.
For 16 loads, uniform distribution and three standard deviations, the axial
load ratio changed from 0.878 in Table 3 to 0.799 in Table 4. This is as
expected since the column load influence surface gradient is steeper near the
middle of the bay than near the corner and consequently calculations of the
column load are more sensitive to the position of loads in the room. For the
141
<_J
fOQJ
c-T*
o1
u.
rzLO
rv1 1 1
oCQ
1
QJ II
o>,
Ll-o OJ J2+->
UJo £: Os: oUJ X.ID o_l S- II
Lj_ Q-CL E
oro 4-> oLU +J_J fOCQ JDeC CT1— UJ
+->
(0 c/)
CJS-<E 13
o Eo i_
cc O1— z:
>>03CO
M-O Ol
-aO 13
-l->
4-1
fOcc cri
to-(->
oOl "OQ. n3(/) OcC _l
C\J
+oo
1/1 1/1
oo
+ +
U~t UJD. Q.
o4->
O UOJ
-O 303 j3O -r-
_J+->
O 4- fOZOO
LO cr> ^£1 COOO C\J CO I
—
CO CO OD CTi
o o o o
C\J Ln l£) o<x> ^ cn ooCO CO CO CTi
o o o o
I— 00 o o-iO to 1— ooCTl 00 CTi
o o o o
00 CM 1— IX)Ln o oocTi en cn CTl
o o o o
o o o-i Lnoo oo oo LnCO 00 CTi
CZ) c>
oo OvJ CTi OU3 1-D ^CO CO 0~i CTi
o o o o
o CO <^ 00I— O UD 1^CTi 0~i CTi CTi
o o o o
CM CO IX) Ooo 1^ CO COCJ1 Cyi C3^ CTi
o o o o
I— c\j Ln en
<^}- 1^Ln oo o CM00 00 cn
o o o o
o oo CO LnCi~i U3 1— oo00 CO CTi cn
o o o o
r-^ o ^ LOoo o oo ^en CTi CTl CTi
o o o o
Ln c\j Ln oo Ln Ln <x)o o~i CTi cn
I— o o o
CO 00 CO 00oo
CO CO o-i cn
o o o o
r~- oo c\jo o LO 00cn cn en
o o o o
LO 00 CO^ I--- COCTi Cn 0~l CTi
o o o o
cn uD cri uDcn CTi cTi cno~i cn C3~i cn
o o o o
I— CM "-n CTl
ZD
cn cTi LO CMO oo 00O CTi CJi cn
r- O O O
CM O LO OO CM O-i1— C7l CTl (Tl
^ i-D .— I
—
CM OO U3 OI— CTi Cn O
O 1— •— <T\LD <-D I—.— cn cn OI— O O I—
CXI CO OO Oto CO LO OCTi Cn CTl oO O O r—
oo CTl 1— oo1X5 o
CTl CTl CTl OO O O I—
o r--~ oo 00CTl IX) ocn (J) CD OO O O I—
r-~ Ln CM IX)1— cn cn f—o cri cn oI— o O r—
CM Ln cn
s-<u+->
-o cuC E
^ o s-O S- OJrt! CL
CO
oo I— oo CMoo Ln <x>o cn cn CTl
t— O O O
Ln Ln CO oix> ^ Ln i-~>o cn cn cn
r- o o o
IX) cn r— CM(Ti Ln CO COo cn cn cn
1— o o o
^ IX) cn COr-^ LO o
«— cn cn oI— o o .—
CO LDCM IX) cn
cn cn cn cn
o o o o
CM "^d- >X) o<x) ^ ocn cn cn oo o o (
00 CO CO <x)
00 IX) 00 ocn cn cn oo o o 1—
00 IX) Lno O r—o o o o
I— CM LO cn
S-QJ+->
-a CDC E:3 T-o s-S- OJta cx
cu+->
CD
S-CDQ.
O
s_o
o-oc:
o
O
OO
142
10 toro ro
<^ CO 1— 00 o CTl CM ro+ + vo CO o
r--. c» cTiCMCO
CTl CTl
r-. COroCTl
^ COro LO
too roto
^ CMro r-~-
roro Ln
LU CTl CO CT CT CT 00 CT CTls: s: o o o o o o o o o o o O o o O oC/1 to
CM+-> ro 00 LO CM CO o ro r-~. to r— CM to CM CM
+ + O CO CTi 1— to C^ 1
—
5- to CTl tocu CO CO 03 CO CTl CTi CTl 00 CTl CTl CT 00 CT CTE oo LUo o o o c O o o O o o o O O O O O
E LO toS- z30) + + CM to LT) CTl — ^ CM ro to O ro CM ro+J o to t>^ 1— CM 1
—
CTl ro LO 00 o ro CO O ro LOc (/I LU CO 00 CTi ai CTl CO CTl CTl CTl CTl CT CT O CT CT CT(D e:O o o o o O o o O o o O O 1— o O Oea- to CTl O r— O to CO r~~. to to CM 00 00 ro CMs- LjU tn r— ^ ^ O to to to to tn LO CT to CT S-
s: O CVl CTl CTl O CTl CT CTl O CT CT CTl QJ4->
Q >, o o o o o o O r- O o o 1— o O O cu
=t (OO CQE'1—
_J to to i-4- ro ro cu
Ll_ 1— to to to CTl CTl 00 CO LO LO Ln CO CO 00 a.o <0 Ln + + CM CM CTl ro CTl CTl CTl to LO Ln CTl LO tn OO 0000 CTl CO o-i 00 CO CO CT CO 00 CT CTl oo c>o LU
LU Ol Q. o o o o o o o O o o O O o o O OCQ Cs: o II o
i-ra
CO toCM CM
Li_ (U • -o «^ ^ (Nj ro LO Ln 1
—
CTl CTl o ro 1^ to to oO +-> CO + + r-^ r— ^ ^ CM i-~~ CO CO CO COfO o CT^ CTl 00 CO CT) CTl 00 CO CTl CTl CO 00 CT CTl
LU E _J LU s_O -1- O Q. o o o o o o o o o o o O o o o o o^ X o 1
—
^-LU O r— n3
i- •1—
_1 Q. II X to to •
Ll_ Q. <c 1
—
ro CM LO LO 'S- o CT o-i ^ oz -o; E + + vf ro LO o o tn 00 ro CT CM CM to CT00 00 CTl CTl CTl CTl CTl CTl CTl CTl CT CT CT CT CTl CTl a
o C/1 LU+-> Q. D- o o o o o o o O o o O O O O O O ns
o•1
—
LU m >-> o_I 3 =! o o CO LO CO CO o ^ 00 CO to ro CT CT ro to *r—
CQ cr -Q OO LU r>« to CTl CTl O cn O O-l CTl o O +Jct LU D. CTl o^ CTl CTl O CTl CT CT CTl o CTl CTl o O 31— J3
+J O O O O o O •— O o o o O O *r—
reCO s_
•1
—
tos_
to
E ^— o T3o (T3 O 4- +-> 1— oj tn CTl CM un CTl r— C\l LO CT 1— CM LO CTo E o o o
S- cu fO
O OO O^— ^—
1 ES_
>> o ola s- 4-CQ
X3ut E E te te
f"
M- rc S- S- cu T3 ai 3O de Lo
S_fo fo un E c E
S-
O 3 +-> O o o+-> to o cu o S- cu C4-
+-> CI. cxcn o
q: O)n3 O
-M 2; >=
IIo to<u T3 T3o. n3 O 4- n3 00 to 00 to</) O o o<: —1 _J
143
practical case of 16 loads with 70 percent located around the perimeter,the column load error at three standard deviations is 16 percent for twosectors versus only two percent for nine sectors. The results in Table 3
and 4 indicate that errors in structural load effects associated with theuse of sectors are sensitive to the location of the room relative to thestructural framing system.
The influence of the manner in which the loads are distributed in the roomis illustrated in Table 5. Results for the uniform distribution and 70 percentaround the perimeter were presented earlier in Table 2. An additional case in
which most of the load is in the center portion (30 percent around perimeter)was also considered. The errors for the cases with 70 and 30 percent aroundthe perimeter are much less than for the uniform distribution. The error dueto using sectors does not appear to be sensitive to the load distribution in
the room for practical distributions, i.e. for load distributions other thanuniform. The results using a lognormal distribution for load magnitude aresimilar to those for the normal distribution. Errors due to using sectors do
not appear to be sensitive to the form of the load magnitude frequency distri-bution.
The results in Table 6 for the case in which the area of the room is approximatelyhalf the area of the bay are similar to those in Table 5. In this case the errorsare less sensitive to the load distribution.
The influence of the variability of load magnitude is indicated in Table 7.
Using a normal distribution for the load magnitude, coefficients of variationof 0.5 and 1.5 were considered. In each case the error due to using sectorsdecreased as the variability increased. For example, the column load error atthree standard deviations for one sector decreased from 0.729 to 0.774 for the
room equal in size to the structural bay.
CONCLUSIONS
The results presented herein indicate that errors in structural load effectscomputed using approximate load locations (sectors) are sensitive to the dis-tribution of the loads in the room, the size of the room relative to the
structural bay and the location of the room relative to the structural framing
system. The errors occurred primarily in the standard deviation and mean values
for the structural loads were not significantly affected. The error for column
moments is more sensitive than the axial load error. The influence of the
number of loads and the form of the load magnitude frequency distribution was
less significant. In most cases, the column load error decreased as the numberof sectors increased. The error in column moment was more erratic and in some
cases increased as the number of sectors increased. For nine sectors, the
error in the column load was less than six percent in all cases considered.
The maximum error at three standard deviations in column moment for nine sectors
was 13 percent. For five sectors the maximum errors at three standard deviations
in column load and moment were 17 percent and 20 percent respectively. The
maximum errors at three standard deviations for two sectors were 27 percent.
144
i
I—
(
onI—00t—) ^Q >,
O CO<o o
o fo
LU CT(_> LU
=) o_l o
(Ut->
s-0)a.
-ac3os-
oCO
o
<5l-
o-o
CO
co
13 LnJD •
•r- OS-4-> II
lO•1- DT3
T3 •
O I—
OE O5- r—oH- II
:3
s- c:o oH- -r-
4->
o 3. J3O -1-
S-II !->
l/l
:> -r-Qr—
1— CO
EII i-
o
>>
CQ
oO a dj
fO oO o 13
_j +->
+->
4-q; O ID
fO-i-> S- IEo 0)O) -oQ. E to(/) o<: _J
+
Q.
c/1
oO M- -l->ZOO
<D00
T3 3fO -QO •--
_l S-+->
l/l
CM 'd- OO aiun ro oi~~- r-- 00 CO
o o o o
<^ I— "^j- 00o 00 CO CO00 r-^ 00 00
o o o o
un r— 00 -=3-
00 un I—00 CO 00 o-i
o o o o
c\j t~-- r-^I— LO >^ LnO CTi CTi CTi
I— o o o
O-i CTl O 00C\J <NJ oo ^r-~. oo CTi
o o o o
CVi
00 CO IX> LT)
r-^ r~- 00
o o o o
1— 1— LO 1.0
r-^ 1— I
—
00 00 CTi CTi
o o o o
00 CO r-. CMo o cri oO O CTi o
33
r-~ O i-D oCTi Ln ^
en CX5 en
o o o o
r-^ o c— cnliD C\J CO uoO CO CO CTi
.— o o o
O U3 cn r-^^ 1— 00I— CO CTl CTi
1— o o o
oo oo COto "vj- CO V£>
CM cn cn o
^ ^ O CMoo CO r~- IX)
CO 00 00 cn
o o o o
1— 1— cnr-^ cn X)
CO CO CO CD
o o o o
r-~. 1— 00CM CM ooCTi cn cn C3~i
o o o o
I— >— CM LnCM CM cn cno o cri CTi
<— r— cz> o
s_OJl-l
"O OJc Er3 -1-
o i-o s- OJ1-^ Q.
UO CM I— OOOO CO00 00 CO 00
o o o o
r-^ "^r ooun CO CTi COCO 00 CO oo
o o o o
CM ^ LD OC7^ O I— OCO CTi CTi cri
o o o o
CM cri CO cnLn oo oo CMCTi cn cn cn
o o o o
1— 1— rj- Ln00 00 o ^00 00 cn CT^
o o o o
cn CTi I— Lncn CM LnCO 00 cn cn
o o o o
00 CO CO oCM CMcn cn cn cn
o o o o
00 CO un X3cn cn
cn CTi CTi cn
o o o o
I— CM Ln cn
s-<D+->
-a 0)c: E13 -i-
o s-o o)oo ro Q-
145
O)-l->
a>Q.
cos-re
oT3
o
t—
1
Q1 CI>s
1
00CQ oQi !->
1— (0 unoo
1 OQ+-> IIQ o to
<CO >^ o'q; -o
U- -(-> -Qo fO oE
LjJ OX E Oo S-
LlJ s_ o33 D- ^- II
CLLl_ e E:z :3
oA-> s_
o oiJD M-
fO 4->
UJ 13 O =3_l O" J3CO UJ O<c S_1— ro II +->
<D tot- :>
<C QEo roo E
II
O— E
>>fOCQ
•4- (/>
O -o O)ro "O
O O 3
ro 4-Ol O
ro+-> s- 2:
Q. E roto 3 O<c s: _i
o
X3roO
toCSJ
+
to toCM (XI
+ +
Q_ a.
tos_
o0 4-+-"Z O U
OJ
O+->
"O 13ro J3O_l
+->
to
<^)- «^ r--. r-~.
LT) oo o txi
00 CO cn cTi
o o o o
O CO CO too-i to I— ooCO CO cTi cn
o o o o
o ^ tnro o CO <3-
cn (J^ cn cTi
o o o o
tn cvi LO oO LT) LT) too cn cn cn
00 00 00 00I— CO r--.
CO 00 o-i CTl
o o o o
CO 1— CO CM>:d- CO LT) toO cn cn cn
I— o o O
tn in CO oto ^ LnO CTl cn cn
to cn I— OJen LT) to COO cn CTl CTl
1— o o o
^ to CTl CO<^ r-~ Ln o.— CTl CTl O.— o o .—
00 toCM to CTl
cn CTl CTl CTl
o o o o
CO CSJo o to 00cn cn cn cn
o o o o
to tn CO COId- CO
cn cn cn cn
o o o o
CTl to cn tocn cn cn cncn cn cn cn
o o o o
I— CM tn cn
OJ >^ to oto r-~ ocn cn cn oo o o r—
CO CO 00 toCO to CO ocn cn cn oo o o .—
CO to tn ^CM o o 1
—
o o o o
1— CM tn cn
CD+->
TD OJ£= E3 -r-
O S-S- curo CL
cn r-~ r--
CO CO tn CM00 cn cn cn
o o o o
CO CM 00 r-~o ^ un CMcn cn cn cn
o o o o
CM tn to COcn cn cn cn
o o o o
1— cn LT) cnLD tn to COcn cn cn cn
o o o o
I— CO cn 1—cn o o
cn cn o oo o .— >—
00 00 cn ocn o o
cn cn o o
00 LT) c» cn00 o o cncn o o cn
o •-^ r-' o
to t-^ r-~. COo r— o cno o o cn
r— CM IT) cn
s-<u+->
"O CI)
e E3 -1-
o s- OJ
I— o r-LO CO O COCO CO cn cn
o o o o
to CO CO COCO LT) I— COCO CO cn cn
o o o o
CO to CO 1^CO cn COcn CO cn cn
o o o o
=d- o oo tn LO too cn cn cn
r— o o o
CM CM C>0 COcxD 00 <l-00 CO cn cn
o o o o
1— o r-- COI— I— tn COcn cn cn cn
o o o o
CO LT) c»^ r-~- COcn cn cn cn
o o o o
cn 1— tocn cn o cncn cn o cn
o o — o
I— CM tn cn
ES_o
146
un 3j3oS-
II -i->
i/i
QEo 034- E
II
c oE
1 1 1
toCO
o4- too -a +-> O)
(C T3o o
_i +->
+J S-<+- +-> C
q; o l/l CPfO
!-> S- s:o O)<u J3 o T3Q. E re n3(/) 3 o O<: _i _l
E
o
o
<:
COn+00
C\J
+oo
Q.
OO
00
COS-o
O M- +->ZOOOJVO
0)-o
(O -r- r>
o c_i a>
E QJO No •.-
od 00
C\J ^ CO oiLO CO Or-- 00 CO
o o o o
i£> .— COo CO oo 0000 00 00
o o o o
LO I— 0000 CD I—00 CO 00 CTl
o o o o
c\j 1^ COI— LT) >;J- LDO CTi C3^ 0~l
I— o o o
cri CTi O 00C\J C^J CO «d-
1-^ 00 CTi
o o o o
CD CD CTl
CO 00 CD un1^ 00 CTi
o o o o
1— r— ID CD1—
CO CO CTl CTi
o o o o
CO 00 cvjo o a^ oo o o-i o.— t— o r—
c\j Ln <Ti
en
o
00 O CD00 Ln r—
r-^ 00 00
o o o o
Cri 00 CD r—CM 00 oo CTl
CO CO CO
o o o o
CD CTi 1— uno-i ^ r—CO 00 00 CTi
o o o o
en CD O CMCM CD COo cn CTi CTi
r— O O O
^ ^ CO1^ un1^ 00 cTi
o o o o
-^i-
1—1— CD00 00 00 cri
o o o o
CO CO cTi
00 00 1—CO 00 CT> CTi
o o o o
CD CD CM COCM CM O Oo o o o
I— CM un cn
^ "ii- r-~. r-~.
un CO o CM00 00 CTi CTi
o o o o
o CO CO LnCTI CD 1— COCO CO CTi CTi
o o o o
1^ O LOCO O COCTl CTl CTi CTl
o o o o
LO CM IT) OO LD IT) COO CJ^ CTi CTl
1— O O O
00 CO 00 00
00 00 CTv CTi
o o o o
r~~ oo CMO O LD 00CTi Cyi CT)
o o o o
CO un CO 00r-^ 00CTt C7^
o o o o
CTi CO CTi CDCT) CJ^ CTl CTi
CTi Cn CTi CTl
CO CM I—CO "Cl- CM CM00 00 CTi CTi
O O O O
>;d- r--. CTl CTlCTl CO CM CM00 CO CTi cn
o o o o
d- o~i o oCO CTl ^ ^CTl 00 CTl CD
o o o o
1— 1— CO CTi1— un un uno CTi cn
r— o o o
un CD un 00cn cn un CD00 00 cn CTi
o o o o
00 CO "=j-
1— 1— CDcn cn cn cn
o o o o
O O 1— COun un CO COcn cn <n cn
o o o o
o o o o
,— CM un cn
un
o
CM O CD 1^o o o <nO O O CTi
1— 1— 1— o
,— CM un cn
ca
to ors +->
cr ca
s-(Uszs_oo
I
toais-
o cn CM COCM CTl cn COCO 00 cn
o o o o
CM cx) o oCD CO 1— ^00 00 cn cri
o o o o
cn I— '^a- CM1— cn CO uncn CO CTl cn
o o o o
o CD 00O CD CO CDo cn cn CTl
cn cn CX3 COcn cn cn CD
00 cn
o o o o
un un 1
—
CM 1^00 CO cn cn
o o o o
r-~. CO CMo o uo COcn cn cn cn
o o o o
CO CO ocn cn o cncn cn o cn
o o 1— o
1— CM un cn
un
o
>>to
S-O)+J
(_)I
to0)
147
It is clear that column loads computed using survey data in which the loadlocations are determined approximately will be less than those computed usingexact load locations. Using two, five, or nine sectors the errors for themean column load and moment should be less than three percent and ten percent,respectively. For extreme values (mean plus N standard deviations) these errorswill increase. Since the errors associated with sectors are related to the
size of the room relative to the structural bay and the location of the roomrelative to the framing system, it would be advisable to record the locationof the framing system in such surveys to assess the relative errors. Thecomputer program employed herein could then be used to assess the error andpossibly develop appropriate correction factors to account for this effect.
148
The following symbols are used in this appendix:
a width of structural bay;
b length of structural bay;
1 number of sectors;
m mean value;
column moment using exact load location;
^Si= column moment using i sectors;
N number of discrete loads;
column load using exact load location;
Psi= column load using i sectors;
s standard deviation;
V coefficient variation;
a aspect ratio for structural bay, a/b; and
B ratio of room dimensions to bay dimensions
149
REFERENCES FOR APPENDIX
1. Bryson, J. 0.; Gross, D., "Techniques for Survey and Evaluation ofLive Floor Loads and Fire Loads in Modern Office Buildings,"Building Science Series 16, National Bureau of Standards, Washington,D.C. , December 1967.
2. Corotis, R. B., "Statistical Measurement and Prediction of BuildingDesign Loads," Thesis presented to the Massachusetts Institute of
Technology, at Cambridge, Massachusetts, in 1968, in partial fulfill-ment of the requirements for the degree of Master of Science.
3. Corotis, Ross B., "Statistical Analysis of Live Load in ColumnDesign," Journal of the Structural Division, ASCE, Vol. 98, No. ST 8,
Proc. Paper 9123, August 1972, pp. 1803-1815.
4. Culver, Charles; Kushner, Jill, "A Program for Survey of Fire Loadsand Live Loads in Office Buildings," Technical Note 858, NationalBureau of Standards, Washington, D.C, May 1975.
5. McGuire, Robin K. ; Cornell C. Allin, "Live Load Effects in OfficeBuildings," Journal of the Structural Division, ASCE, Vol. 100,
No. ST 7, Proc. Paper 10660, July 1974, pp. 1351-1366.
6. Mitchell, G. R.; Woodgate, R. W., "Floor Loadings in Office Buildings -
The Results of a Survey," Current Paper 3/71, Building ResearchStation, England, January 1971.
7. Peir, Jong-Cherng; Cornell, C. Allin, "Spatial and Temporal Varia-
bility of Live Loads," Journal of the Structural Division, ASCE,Vol. 99, No. ST 5, Proc. Paper 9747, May 1973, pp. 903-922.
150
klBS-114A (REV. 7-73)
u.b.»utKi . ui- i.,uMM. i_ Pui^LlCATlON OR RF.FORT NO. 2. Ciov t Accession
'''''°''sh'e''eT'^'^ NBS BSS-85
3. Recipient's Accession No.
4. TITLE AND SUBTITLE
Survey Results for Fire Loads and Live Loads in OfficeBuildings
5. Publication Date
May 1976
6. Performing Organ i zat ion Code
460.03
7. AUTHOR(S)
Culver, Charles G.
8. Performing Organ. Report No.
9. PERFORMING ORGANIZATION NAME AND ADDRESS
NATIONAL BUREAU OF STANDARDSDEPARTMENT OF COMMERCEWASHINGTON, D.C. 20234
10. Project/Task/Work Unit No.
460-550611. Contract /Grant No.
BRAB 27-73-5312. Sponsoring Organization Name and Complete Address (Street, City, State, ZIP)
Public Buildings Service National Academy of SciencesGeneral Services Administration Bldg. Research Advisory Board
Washington, D.C. 20405 2100 Pennsylvania AvenueWashington, D.C. 20418
13. Type of Report & PeriodCovered
Final June 197 3-
December 197
S
14. Sponsoring Agency Code
31da. Research Advisory15. SUPPLEMENTARY NOTES Board
Library of Congress Catalog Card Number: 76-608115
16. ABSTRACT (A 200-word or less factual summary of most si^ifleant information. If document includes a significant
bibliography or literature survey, mention it here.)
Fire load and live load data obtained from a survey of 23 office buildings locatedin various regions throughout the United States are presented. The survey designis described including the characteristics of the building population used to selectthe sample. Data are presented on the magnitude and distribution of the loads.
Information is also included on the characteristics of office loads such as the typeof items (furniture, equipment, etc.) and their properties (material type, dimensionsexposure, etc). Statistical summaries of the data and a determination of the build-ing and occupancy characteristics affecting these loads are presented. The data do
not indicate any significant differences between the loads in private and governmentbuildings. Similarly, geographic location, building height, and building age werenot found to have a significant influence on load magnitude. The use of the roomssurveyed, however, did affect load magnitude. A mathematical model developed froma regression analysis of the survey data is presented for calculating fire loads and
live loads in offices. The data presented may be used to evaluate current require-ments for design loads for buildings.
17. KEY WORDS (six to twelve entries; alphabetical order; capitalize only the first letter of the first key word unless a proper
name; separated by semicolons)
Buildings; fire loads; load surveys; occupancy live loads; Structural engineering.
18. AVAILABILITY \^ Unlimited
1 1For Official Distribution. Do Not Release to NTIS
1 1Order From Sup. of Doc, U.S. Government Printing Office
Washineton. D.C. 20402. SD Cat. No. CU. 29/2: 85
IX 1Order From National Technical Information Service (NTIS)Springfield, Virginia 22151
19. SECURITY CLASS(THIS REPORT)
UNCL ASSIFIED
21. NO, OF PAGES
157
20. SECURITY CLASS(THIS PAGE)
UNCLASSIFIED
22. Price
$ 2.25
USCOMM-DC 29042-P74
ftU.S. GOVERNMENT PRINTING OFFICE;197p 210-80!';-?
NBS TECHNICAL PUBLICATIONS
PERIODICALS
JOURNAL OF RESEARCH reports National Bureauof Standards research and development in physics,
mathematics, and chemistry. It is published in two sec-
tions, available separately:
• Physics and Chemistry (Section A)
Papers of interest primarily to scientists working in
these fields. This section covers a broad range of physi-
cal and chemical research, with major emphasis onstandards of physical measurement, fundamental con-
stants, and properties of matter. Issued six times a
year. Annual subscription: Domestic, $17.00; Foreign,
$21.26.
• Mathematical Sciences (Section B)
Studies and compilations designed mainly for the math-ematician and theoretical physicist. Topics in mathe-matical statistics, theory of experiment design, numeri-cal analysis, theoretical physics and chemistry, logical
design and programming of computers and computersystems. Short numerical tables. Issued quarterly. An-nual subscription: Domestic, $9.00; Foreign, $11.25.
DIMENSIONS/NBS (formerly Technical News Bul-
letin)—This monthly magazine is published to informscientists, engineers, businessmen, industry, teachers,
students, and consumers of the latest advances in
science and technology, with primary emphasis on the
work at NBS. The magazine highlights and reviews suchissues as energy research, fire protection, building tech-
nology, metric conversion, pollution abatement, health
and safety, and consumer product performance. In addi-
tion, it reports the results of Bureau programs in
measurement standards and techniques, properties of
matter and materials, engineering standards and serv-
ices, instrumentation, and automatic data processing.
Annual subscription: Domestic, $9.46; Foreign, $11.86.
NONPERIODICALS
Monographs—Major contributions to the technical liter-
ature on various subjects related to the Bureau's scien-
tific and technical activities.
Handbooks—Recommended codes of engineering andindustrial practice (including safety codes) developedin cooperation with interested industries, professional
organizations, and regulatory bodies.
Special Publications—Include proceedings of confer-
ences sponsored by NBS, NBS annual reports, and otherspecial publications appropriate to this grouping suchas wall charts, pocket cards, and bibliographies.
Applied Mathematics Series—Mathematical tables,
manuals, and studies of special interest to physicists,
engineers, chemists, biologists, mathematicians, com-puter programmers, and others engaged in scientific
and technical work.
National Standard Reference Data Series—Providesquantitative data on the physical and chemical proper-ties of materials, compiled from the world's literature
and critically evaluated. Developed under a world-wide
program coordinated by NBS. Program under authority
of National Staadard Data Act (Public Law 90-396).
NOTE: At present the principal publication outlet for
these data is the Journal of Physical and ChemicalReference Data (JPCRD) published quarterly for NBSby the American Chemical Society (ACS) and the Amer-ican Institute of Physics (AIP). Subscriptions, reprints,
and supplements available from ACS, 1165 SixteenthSt. N. W., Wash. D. C. 20056.
Building Science Series—Disseminates technical infor-
mation developed at the Bureau on building materials,
components, systems, and whole structures. The series
presents research results, test methods, and perform-ance criteria related to the structural and environmen-tal functions and the durability and safety character-
istics of building elements and systems.
Technical Notes—Studies or reports which are completein themselves but restrictive in their treatment of a
subject. Analogous to monographs but not so compre-hensive in scope or definitive in treatment of the sub-
ject area. Often serve as a vehicle for final reports of
work performed at NBS under the sponsorship of other'
government agencies.
Voluntary Product Standards—Developed under pro-
cedures published by the Department of Commerce in
Part 10, Title 15, of the Code of Federal Regulations.
The purpose of the standards is to establish nationally
recognized requirements for products, and to provide
all concerned interests with a basis for common under-standing of the characteristics of the products. NBSadministers this program as a supplement to the activi-
ties of the private sector standardizing organizations.
Federal Information Processing Standards Publications(FIPS PUBS)—Publications in this series collectively
constitute the Federal Information Processing Stand-ards Register. Register serves as the official source of
information in the Federal Government regarding stand-ards issued by NBS pursuant to the Federal Propertyand Administrative Services Act of 1949 as amended,Public Law 89-306 (79 Stat. 1127), and as implementedby Executive Order 11717 (38 FR 12315, dated May 11,
1973) and Part 6 of Title 15 CFR (Code of FederalRegulations).
Consumer Information Series—Practical information,based on NBS research and experience, covering areasof interest to the consumer. Easily understandablelanguage and illustrations provide useful backgroundknowledge for shopping in today's technologicalmarketplace.
NBS Interagency Reports (NBSIR)—A special series of
interim or final reports on work performed by NBS for
outside sponsors (both government and non-govern-ment). In general, initial distribution is handled by thesponsor; public distribution is by the National TechnicalInformation Service (Springfield, Va. 22161) in papercopy or microfiche form.
Order NBS publications (except NBSIR's and Biblio-
graphic Subscription Services) from: Superintendent ofDocuments, Government Printing Office, Washingrton,D.C. 20402.
BIBLIOGRAPHIC SUBSCRIPTION SERVICESThe following current-awarenesa and literature-survey
bibliographies are issued periodically by the Bureau:Cryogenic Data Center Current Awareness Service
A literature survey issued biweekly. Annual sub-scription: Domestic, $20.00; foreign, $25.00.
Liquefied Natural Gas. A literature survey issued quar-
terly. Annual subscription: $20.00.
Superconducting Devices and Materials. A literature
survey issued quarterly. Annual subscription : $20.00.Send subscription orders and remittances for thepreceding bibliographic services to National Bu-reau of Standards, (Cryogenic Data Center (275.02)Boulder, Colorado 80302.
EUectromagnetic Metrology Current Awareness Service
Issued monthly. Annual subscription: $24.00. Sendsubscription order and remittance to ElectromagneticsDivision, National Bureau of Standards, Boulder,
Colo. 80302.
U.S. DEPARTMENT OF COMMERCENational Bureau of StandardsWashington. D.C. 20234
OFFICIAL BUSINESS
Penalty for Private Use, $300
POSTAGE AND FEES PAIDU.S. DEPARTMENT OF COMMERCE
COM-215U.S.MAIL
SPECIAL FOURTH-CLASS RATE
BOOK
,ov.^JTlO/^
YEARS
top related