torque limiters - clutches
Post on 10-Jan-2022
10 Views
Preview:
TRANSCRIPT
torque limiters - CLUTCHES
��������������
II
Application Book «TORQUE LIMITERS - CLUTCHES»: introduction
ComInTec torque limiters are mechanical components necessary to fit along the kinematic chain and are preferred to electronic safety
devices because of a better response time, improved reliability, excellent configuration flexibility, easy fitting and adjustment, use at high
speeds in hard environments in the presence of inertias and important masses. In fact the electronic systems, which normally act up to the
transmission, present: delayed reaction time, many factors as a source of error, configuration and management complexity.
The fitting of the mechanical torque limiters along the kinematic chain is therefore necessary for a reliable and complete protection, in order
to improve the level of safety and the machine, according to the new EN ISO 13489-1 standards, reducing the average possible broken-down
and unproductive downtime.
Benefits of our models …
Long product life with continuous reliability.
Optimum protection against environmental conditions.
Simple mounting for in-line and parallel transmission.
Easy setting and adjustment.
Highly accurate and fast machine protection.
Special designs to suit specific applications possible.
Competitive pricing without sacrificing quality.
"Made in Italy" with certified quality.
Our product range ...
"DF": Simple, economical and suitable for dry and dusty conditions.
"EDF/F": Compact and low cost ball version available with sprocket or flange.
"DSS or DSR": Offering high stability during operation. Re-synchronising in various positions possible. A full range of mounting
options are possible.
"DSS/SG": Allows immediate disconnection without any residual torque remaining.
"DSA": Suitable for limiting compression and tension forces on crank mechanisms.
: Possibility of varying the transmission torque during operation and allowing for full disengagement with free rotation if"AP"
required.
Economical overload protection device
with ball transmission via a customized
sprocket that disengages fully when it
reaches the pre-set peak torque. The
torque is steplessly adjustable by altering
the spring pressure.
Overload protection device with Ball or
Roller transmission, which disengages fully
at the pre-set peak torque. The torque is
steplessly adjustable by altering the spring
pressure.
Overload protection device with a
sprocket mounted between two friction
discs that slide without disengaging when
it reaches the pre-set peak torque. The
torque is adjustable by altering the
spring pressure.
ECONOMY BALL TORQUE LIMITER “EDF/F” BALL OR ROLLER TORQUE LIMITER “DSS or DSR”FRICTION TORQUE LIMITER “DF”
BACKLASH FREE TORQUE LIMITER “DSS/SG” PNEUMATIC CLUTCHES “AP”AXIAL FORCE LIMITER “DSA”
A backlash free overload protection devicewith ball transmission, that disengagesfully at the pre-set peak torque. Very highsensitivity possible with negative springversion.
Friction or roller clutches with adjustment
of the peak torque possible remotely by
altering the pneumatic pressure.
Device that disengages in the axial
direction (in compression and tension) at
the pre-set force by altering the spring
pressure.
Application Book «TORQUE LIMITERS - CLUTCHES»: introduction
THE PRODUCT FUNCTION
By far the most common application for a Torque Limiter is as a safety device designed to provide a partial ,or complete disconnection
between the Driving and Driven components of a machine assembly.
The disconnection is to prevent damage to the machine components or products in the event of an overload .
The principle being the relative low cost of a Torque Limiter, can if called upon prevent terminal and high cost damage to Machinery , or
reducing production downtime by isolating the machine inertia.
SO, THE TORQUE LIMITER IS ESSENTIAL FOR:
Protects the motor-gearbox in case of accidental collision.
Protects the gearbox from jamming due to foreign matters.
Protects the gear in case of short product jam.
Absorbs static torques without disengaging.
To protect slides or servomotors against impact or limit stops.
Protects conveyor belts in case of product collisions.
Protects packages from squashing and deforming.
Protects the product from damage or wrong positioning.
Engage/disengage different product transmission lines.
Maintain tension of wire/film coils.
IIIKEY COMINTEC SALES POINT:
40 years of torque limiter applications.
Quality system ISO 9001.
Wide range of product.
Origin of material certified.
Industrialized and competitive production.
Customized production and application assistance.
Optimized technical solution.
Prototypes and small batches possible.
Factory torque setting available.
Quality control guaranteed.
Careful assembly.
Research on continuos development of products.
Export word wide.
Customer friendly webtools (3D drawings, Instruction sheets, website always update.
Application Book «TORQUE LIMITERS - CLUTCHES»: MECHANICAL Vs ELECTRONIC
IV
WHY USE A MECHANICAL TORQUE LIMITER INSTEAD OF ELECTRICAL SENSING?
Machine designers are always looking for ways
to provide machine safety to reduce damage
caused by accidental collisions which can lead
to replacement costs and lost production for
the end customer. As machine designs today
are increasingly reaching new mechanical and
productivity limits, the need for fast,
comprehensive protection is becoming even
more important. The Mechanical units offered
by ComInTec address that need and offer
distinct advantages in a wide range of
applications.
Mechanical
The mechanical torque limiter / overload
safety coupling is designed to protect key
components of machinery and systems from
overloads. These devices will overload when a
pre-set calibration torque is reached, as this
setting is lower than the breaking point of the
weakest drive component. The units are simple
to calibrate and can be easily adjusted to suit
different areas of the machine.
Why is electrical sensing seen as an economical alternative?
Electrical
Electronics and control technology have advanced at the same pace as the development of today's high speed and precision machines,
leading many customers to believe that a lower cost option is to control torque levels electrically by monitoring the motor current or
temperature.
Increasingly, motor current dependent systems are being used though there are 2 distinct disadvantages when compared to the mechanical
torque limiter.
I. When an overload occurs and there is a sharp increase in the torque because of a crash situation a signal from the monitoring circuit must
first be sent to the controller. The controller then attempts to increase the torque until it reaches the preset value which can in most cases
take the same amount of time again before the drive is actually stopped. Depending on the application, this can be anywhere from 15-20
milliseconds.
A mechanical limiter will allow for instant disengagement of the driver from the driven and when installed in a strategic position will
significantly reduce the reaction time to 1/3 of that offered by the electrical sensing.
Another key advantage is that complete disconnection will, in addition, remove the impact from the shock of the collision, in particular
where high speeds and inertias are involved. With electrical torque control the drive will eventually be stopped but due to the shock impact
present a high level of damage can still occur.
II. Another disadvantage of the electrical method is the number of areas where a failure can occur. Electrical methods generally require a
number of sensors to ensure maximum protection, and in addition, customers may use additional torque sensing devices as secondary
systems. This complex arrangement only adds to the costs and potential failure points.
A mechanical torque limiter can be used simply, one on each axis only, providing complete disconnection between the driver and driven
with fast easy adjustment possible over a broad range.
Disadvantages of Electrical:
10-15 millisecond reaction times ultiple sensors required nsuitable for high speed or large inertias Complex arrangements; m ;l u ;
Advantages of Mechanical:
1/3 of the reaction time 1 unit per axis only, can be positioned anywhere on the drive train Simple set up with easy adjustment; ; ;
Potentially lower overall costs Absorption of shock loads Use at high Speeds Better reliability Use in heavy environments; ; ; ; ;
Excellent configuration versatility.
How will the New EN ISO 13849 standards impact machine designers?
The common categories of inspection for the safety of machinery will be upgraded to a higher level, in accordance with EN ISO 13849
standards. To meet this standard, the designers of machines and systems will need to allow for the installation of suitable control and/or
safety systems.
ComInTec torque limiters, designed in accordance with modern engineering practices, are proposed as mechanical components required
for installation within the drive chain in order to maximize the safety level of the machine, according to the new EN ISO 13489 -1 standard.
Therefore, the aim is to prevent and avoid damage or deformation of mechanical parts due to sudden or accidental overload, reducing the
probability of failure and unproductive downtime.
The new legislation compliance date has been extended until late 2011, due to the difficult and unclear interpretation. The current standard
EN 954-1 remains in force up to this date.
Application Book «TORQUE LIMITERS - CLUTCHES»: application selection guide
- base version
.../ML (with long hub)
.../SI (with intervention signal)
.../CM (with helical springs)
.../PR (for gearboxes - fitted on the output hollow shaft)
... + GAS (jaw coupling)
... + GEC (compact elastic coupling)
DF model
Model / Version and Sector
.../C (with plate wheel)
.../F (with with flange)
.../TAC (with chain coupling)
EDF model
V
- base version
.../ML (with long hub)
.../FS (with supporting flange)
.../CM (with helical springs)
.../SMO (with one-way rotation)
.../AM (with with mechanical stop)
.../TAS (with pin stops)
... + GTR (with torsionally rigid disc coupling)
... + GAS (with jaw coupling)
... + GEC (with compact elastic coupling)
DSS - DSR - DSR/F - DSR/F/RF model
Se
ctio
n «
D»
CO
NV
EY
OR
S
Se
ctio
n «
M»
AE
RO
SP
AC
E I
ND
US
TR
Y
.../PR-V (for gearboxes - fitted on the input shaft)
.../TAC (with chain coupling)
- base version «6 hole»
.../P (positive version)
.../N (negative version)
.../ML (with long hub)
.../PR-V (for gearboxes - fitted on the input shaft)
... + GSF (with bellow coupling)
... + GAS (with jaw coupling)
DSS/SG - DSS/F/SG model
Se
ctio
n «
I»
WO
OD
WO
RK
ING
Se
ctio
n «
E»
TR
AN
SP
OR
TAT
ION
SY
ST
EM
- base version
DSA model
- base version
.../CS (with ball bearing)
... / TAC (with chain coupling)
... + GEC (with compact elastic coupling)
DSR/F/AP - DSF/TF/AP model
Se
ctio
n «
B»
LAB
ELL
ING
Se
ctio
n «
F»
PA
PE
R
Se
ctio
n «
H»
MA
RIN
E E
NG
INE
ER
ING
Se
ctio
n «
C»
BO
TT
LIN
G
... + GEC (with compact elastic coupling)
Se
ctio
n «
G»
MA
CH
INE
TO
OLS
Se
ctio
n «
L»
HE
AV
Y I
ND
US
TR
Y
Se
ctio
n «
A»
PA
CK
AG
ING
Se
ctio
n «
Z»
OT
HE
R
PACKAGING
Section «A»
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
CARTON ERECTOR
Fitted on main drive gearbox for complete
system protection.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
.../ML
Model:
Version:
Type of machine:
Where applied
and what protect:
POWDER FILLING
Protection for the main drive star wheel and
scroll feed.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
.../ML
Model:
Version:
Type of machine:
Where applied
and what protect:
TRAY SEALER
Used as a clutch, allows disconnection of feed
rollers in case of wrap around of film.
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version
Model:
Version:
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
PACKAGING MACHINES
Applied on handling of the packages, it
protects them from the high pressures or
deformations during the packaging process.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
DIAPER'S PRODUCTION MACHINES
Applied at the product handling line it
protects in case of accumulation and
disorientation of material.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F ; DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
SHRINK PACKAGING MACHINE
Applied to the motion line of the film it
protects the film from eventual deformation
and accidental breakings.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
SHRINK WRAPPING
Applied on the material handling used for
packaging. It protects the film from excessive
traction avoiding breakings or deformations.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
WRAP-AROUND CARTONING
Applied on the material handling used for
packaging. It protects the film from excessive
traction avoiding breakings or deformations.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
TOBACCO MACHINES
Applied on the transmission line of the
product, it protects the product in motion
from deformation and/or bad positioning.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
PACKAGING BLISTERS MACHINES
Applied on the closure mechanism in order to
protect the packages.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F ; DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
UNSCRAMBLING PALLETISING MACHINES
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
... / AM
Model:
Version:
Type of machine:
Where applied
and what protect:
FOOD PROCESSING LINE
Applied on the handling of the material, it
protects the products from crushings during
the working process.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
base version
Model:
Version:
Section «A» - PACKAGING
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
PACKERS MACHINES
Applied on handling of the packages, it
protects them from deformations and
anomalous squashings during the packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version ; .../AM
Model:
Version:
Type of machine:
Where applied
and what protect:
BUBBLE-GUM FLOW-WRAP MACHINES
Applied on handling of the packages, it
protects them from the anomalous pressures
or deformations during the packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
STRAPPING MACHINES
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
FILM STRETCHING MACHINES
It protects the packaging material from pulls
and heavy pressures, avoiding breakings or
deformations.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
PACKAGING MACHINES
Applied on the handling for the packages
handling, it protects them from the
anomalous pressures or pushes during the
packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F ; DSA
base version ; ... / SMO
Model:
Version:
Type of machine:
Where applied
and what protect:
PACKERS MACHINES
Applied on handling of the packages, it
protects them from tpossible high pressures
or deformations during the packaging process.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Section «A» - PACKAGING
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
CARTONING MACHINES
Applied on handling of the packages, it
protects them from the anomalous pressures
or deformations during the packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
WRAPPING MACHINES
Applied on handling of the packages, it
protects them from the anomalous pressures
or deformations during the packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
BOX MACHINERY
Applied on line handling envelopes, to receive
the motorcycle by a cam. Protect the product
from deformation.
Photo and/or drawing product:
Photo and/or drawing application:
DSA
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
PACKAGING MACHINES WITH ROTARY CUTTING
Applied on the handling of the blades which
cut the film for packaging, it needs to regulate
the different forces with whom the blades
must to cut the several film's thicknesses.
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
FLOW-WRAP
Applied on the handling of the blades which
cut the film for packaging, it needs to regulate
the different forces with whom the blades
must to cut the several film's thicknesses.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
HORIZONTAL PACKAGING
It protects the packages from crushings and
the packaging material from tears due to
incorrect wrapping. Also fitted between g'box
and angle gear to change pack size.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG ; DSR/F/AP
base version
Model:
Version:
Section «A» - PACKAGING
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
PACKAGING MACHINES IN FOOD FIELD
It protects the packages from crushings and
the packaging material from tears due to
anomalous wrapping.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
MAGAZINES AND NEWSPAPERS PACKAGING
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
CD AND DVD PACKAGING MACHINES
The material's transmission line, it protects
the packages to be packaged from crushings,
deformations, or bad positioning.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N
Model:
Version:
Type of machine:
Where applied
and what protect:
TAKE UP MACHINES OF SHRINK MATERIAL
Applied on the products handling lines, it
needs to stop the transmission when
accumulating the product.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../P
Model:
Version:
Type of machine:
Where applied
and what protect:
FOOD PACKAGING
Fitted on axial of the coil. Used to
disconnection of a driven shaft to refeed
plastic film.
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version with bearing + Niploy
Model:
Version:
Type of machine:
Where applied
and what protect:
FOOD PACKAGING
...
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../ML/N
Model:
Version:
Section «A» - PACKAGING
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
PACKAGING AND STRETCH MOLDING
Applied on the products handling lines, it
needs to stop the transmission when
accumulating the product.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../P
Model:
Version:
Type of machine:
Where applied
and what protect:
PACKAGING MACHINE WITH ROTARY JAWS
Applied in the movement of the film needed
to close the package, it protects the film from
break when an excessive traction happens.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG ; EDF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
DEPALLETISERS MACHINES
Applied on handling of the packages, it
protects them from deformations and high
pressures during the packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N
Model:
Version:
Type of machine:
Where applied
and what protect:
DEPALLETISERS MACHINES
Applied on handling of the packages, it
protects them from deformations and high
pressures during the packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
PACKAGING MACHINES
Applied on the handling for the packages
handling, it protects them from the
anomalous pressures or pushes during the
packaging.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../P
Model:
Version:
Type of machine:
Where applied
and what protect:
SHRINK TUNNEL
Assembled on the handling components of
the product being packed, it protects from
deformation caused by crushing, clogging and
bunching.
Photo and/or drawing product:
Photo and/or drawing application:
EDF ; DF
base version
Model:
Version:
Section «A» - PACKAGING
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
ROLLER SHRINKABLE
Assembled on the handling of the material
that has to be packed, it protects the material
from deformation caused by crushing,
clogging and bunching.
Photo and/or drawing product:
Photo and/or drawing application:
DF ; DSF/MFR
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
STRAPPING MACHINES
It connects the nozzle to the bayonet that is
needed to wrap the package with the
strapper, it protects the nozzle and the engine
by obstacles on handling.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
STRAPPING MACHINES
It connects the nozzle to the bayonet that is
needed to wrap the package with the
strapper, it protects the nozzle and the drive
from obstructions on handling.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
FEEDERS FOR INDUSTRIAL AUTOMATION FIELD
Protects the motion reducer and the plant in
case of stoppage and overloads.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version ; .../PR-V
Model:
Version:
Type of machine:
Where applied
and what protect:
PACKAGING MACHINES FOR DIAPERS
Applied at the product handling line, it slide in
case of accumulation and disorientation of
material.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
FILLING MACCHINES
Applied at the loading line of the material to
be filled, it protects in case of stoppage and
bad positioning of the product.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F
Model:
Version:
Section «A» - PACKAGING
Section «A» - PACKAGING
Type of machine:
Where applied
and what protect:
ROLLOER TENSIONING
...
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
special version
Model:
Version:
LABELLING
Section «B»
Section «B» - LABELLING
Type of machine:
Where applied
and what protect:
LABELLING MACHINES
Applied on the motion of the belt with the
labels for packing and bottles, it protects the
belt from stretching and sudden tearing.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
... / AM ; ... / FS
Model:
Version:
Type of machine:
Where applied
and what protect:
LABELLING MACHINES
It protects the product's packages from the
peak pressures or pushes during the labelling.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
ROTARY LABELLING
Overload protection for main drive on the star
wheel and scroll feed also.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
LABELLING ROLL MACHINE
Fitted on the roll of labels for bottles. Stop the
transmission in case of film jam.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
.../FS
Model:
Version:
Type of machine:
Where applied
and what protect:
LABELLING ROLL MACHINE
Fitted under the table of in/out bottles. Stop
the transmission in case of bottles jam.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
…/N
Model:
Version:
Type of machine:
Where applied
and what protect:
TENSIONERS
Mounted on the coil. Used as tension during
the fixing labels.
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version
Model:
Version:
Section «B» - LABELLING
Section «B» - LABELLING
Type of machine:
Where applied
and what protect:
ROTARY MACHINES
Fitted on main drive to rotating starwheel , to
protect the drive incase of missfeed of
product.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N
Model:
Version:
Type of machine:
Where applied
and what protect:
DIE-CUTTING MACHINE
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR
base version
Model:
Version:
BOTTLING
Section «C»
Section «C» - BOTTLING
Type of machine:
Where applied
and what protect:
FILLING MACHINES
Applied under the turntable, it protects the
badly positioned bottles.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
WIRE HOODING MACHINES FOR BOTTLES
Applied on the input shaft of the gearbox, it
leads a pulley that has to go round axially, to
avoid whippings. It protects the machine and
the packagings.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
CAPPING MACHINES.
Applied on the input shaft of the gearbox, it
leads a pulley that has to go round axially, to
avoid whippings. It protects the machine and
the packagings.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
BOTTLE'S RINSING AND BOTTLING MACHINES
Applied under the turntable, avoids bad
positioning of the bottles.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
CORKING MACHINES
Applied on the corks closure line, it needs to
regulate the different torque wrench setting,
according to the sizes.
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
FILLING MACHINES
Applied under the turntable, it protects the
badly positioned bottles.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N
Model:
Version:
Section «C» - BOTTLING
Section «C» - BOTTLING
Type of machine:
Where applied
and what protect:
BOTTLING MACHINES
Applied on the rotating table, it protects the
bottles from crushing due to a bad positioning
during the handling.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F
Model:
Version:
CONVEYORS
Section «D»
Section «D» - CONVEYORS
Type of machine:
Where applied
and what protect:
AUTOMOTIVE
On main drive to protect in case of overload
on the conveyor system.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F
Model:
Version:
Type of machine:
Where applied
and what protect:
CONVEYOR FOR HEAT TREATMENT FURNACES
Fitted on output shaft of gear-box for the
control of conveyor during the progress of the
material.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../ML
Model:
Version:
Type of machine:
Where applied
and what protect:
CONVEYOR
...
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../C ; .../F
Model:
Version:
Type of machine:
Where applied
and what protect:
OVER HEAD CONVEYORS
Applied at the beginning of the transmission it
protects the gearmotor and the system in case
of stoppage of the line.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
base version
Model:
Version:
Type of machine: CONVEYOR SYSTEMS WITH AUTOMATED
SELECTIVE LOADING/UNLOADING
Applied on the motion, it protects the
conveyor belt from overloading of material.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F ; DF
base version
Model:
Version:
Type of machine: MECHANICAL FEEDERS FOR INDUSTRIAL
AUTOMATION FIELD
Assembled on the augers' transmission it
protects the product from overloads.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version
Model:
Version:
Where applied
and what protect:
Where applied
and what protect:
Section «D» - CONVEYORS
Section «D» - CONVEYORS
Type of machine:
Where applied
and what protect:
CHIP CONVEYORS
Assembled on the reduction gearbox output
shaft which moves the belt, it protects the
conveyor belt.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../C
Model:
Version:
Type of machine:
Where applied
and what protect:
OVER HEAD CONVEYORS
Applied out of gear-box, it protects the
engine, the gear-box and the system, when
the line hinds.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
TRANSPORT, HEAP AND END OF MACHINE
Assembled on the roller motion it protects the
product from accidental collisions with
adjacent products.
Photo and/or drawing product:
Photo and/or drawing application:
DF ; EDF/F
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
...
Applied at the beginning of the trasmission on
the gearbox's output shaft, it protects the
whole kinematics chain from overload.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
ASSEMBLY MACHINES
Applied on the motion of the conveyor belt it
avoids accidental overloading of the system.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
CONVEYOR GLASS SHEETS
Fitted between output shaft of gear-box and
universal joint for the control of conveyor
during the progress of the glass plates. Used
as a trailing-end to protect the material.
Photo and/or drawing product:
Photo and/or drawing application:
DF
special .../CR (with radial bearing)
Model:
Version:
Section «D» - CONVEYORS
Section «D» - CONVEYORS
Type of machine:
Where applied
and what protect:
MOTORIZED TRANSPORT LINES
...
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
OVERHEAD CONVEYOR
Applied on the gearbox's output shaft, it
protects the gearbox and the motor from
eventual obstacles.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
TRANSPORTERS
Applied in out shaft of motor step by step for
transfer of items on line, it protects the motor.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
CONVEYOR GLASS SHEETS
Fitted on output shaft of gear-box for the
control of conveyor during the progress of the
glass plates. Used as a trailing-end to protect
the material.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../ML
Model:
Version:
Section «D» - CONVEYORS
TRANSPORTATION SYSTEM
Section «E»
Section «E» - TRANSPORTATION SYSTEM
Type of machine:
Where applied
and what protect:
AUTOMATIC DOORS: RESIDENTIAL GATES
Open gates residential. Mechanical protection,
in addition to the electronic, and slip in case of
obstacles.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOOR: TOILET FOR AUTOGRILL
Fitted on output shaft of gear-box for the
control of open/close of tripod.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOOR
...
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
with integrate elastic coupling
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOORS:
UNDERGROUND/SUPERMARKET GATE
Applied on movable doors, protect the
gearbox from accidental or vandalic heavy
pushes.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version with LDX friction rings
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOORS:
UNDERGROUND/SUPERMARKET GATE
Applied on movable doors, protect the
gearbox from accidental or vandalic heavy
pushes.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F
Model:
Version:
Type of machine:
Where applied
and what protect:
ENTRANCE GATE
Fitted on the drive system to prevent damage
in case is blocked from moving.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N ; ... + GAS
Model:
Version:
Section «E» - TRANSPORTATION SYSTEM
Section «E» - TRANSPORTATION SYSTEM
Type of machine:
Where applied
and what protect:
AUTOMATIC DOOR: SWING GATE
Fitted out of the motor. Protects the motor
from overload due to obstacles in opening
/closing.
Photo and/or drawing product:
Photo and/or drawing application:
DF
../TAC with LDX friction rings
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOOR: DOORS FOR BUS
Fitted on output shaft of gear-box for the
control of open/close automatic doors of bus.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOOR: TOILET FOR TRAIN
Fitted on output shaft of motor for the
control of open/close doors for toilet train.
Used as a trailing-end to protect the motor.
Photo and/or drawing product:
Photo and/or drawing application:
DF
with LDX friction rings + GD
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOOR: RAMP OF AMBULANCE
Fitted between motor-gearbox,Slip when
reaching final closed and open position.
Protect the motor.
Photo and/or drawing product:
Photo and/or drawing application:
DF
... + GAS with long life friction rings
Model:
Version:
Type of machine:
Where applied
and what protect:
TRAIN
Fitted between hand drive to connect to
gearbox to raise and lower upper car deck.
Photo and/or drawing product:
Photo and/or drawing application:
DF
special .../EA (RUST RESISTANT)
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTOMATIC DOOR: BUS DOOR
Fitted in output shaft of the motor for the
door movement. Protect the motor from
obstacles during open/close.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F with gear
Model:
Version:
Section «E» - TRANSPORTATION SYSTEM
Section «E» - TRANSPORTATION SYSTEM
LIFTING SYSTEM BINARIES
Fitted in the lift system manual to limit the
force due to breakoge the tool.
Photo and/or drawing product:
Photo and/or drawing application:
EDF
.../F
Model:
Version:
Type of machine:
Where applied
and what protect:
AUTO GLASS ASSEMBLY
...
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N ; ... + GSF
Model:
Version:
Type of machine:
Where applied
and what protect:
Type of machine:
Where applied
and what protect:
TANK TRUCK COMPRESSORS
Cushions pickups and protects the compressor
against bunching of material (to be set on
both sides).
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version + Cardan Flange
Model:
Version:
Section «E» - TRANSPORTATION SYSTEM
Section «E» - TRANSPORTATION SYSTEM
Type of machine: AUTOMATIC DOOR: UNDERGROUND/AIRPORT
GATE
Fitted beetwen gear-box and universal joint.
Protects the gear-box from overload due to
obstacles in opening /closing.
Photo and/or drawing product:
Photo and/or drawing application:
EDF
.../F with bearing
Model:
Version:
Where applied
and what protect:
Section «E» - TRANSPORTATION SYSTEM
PAPER MACHINE
Section «F»
Section «F» - PAPER MACHINE
Type of machine:
Where applied
and what protect:
PAPER MACHINES
Applied on the paper film handling, itprotects
the film from excessive traction avoiding ist
breaking and deformation.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
PAPER MACHINES
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
BOOK MAKING
Fitting on the material's transmission line, it
protects the packaging to be sewed from
crushing, deformation or bad positioning.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N
Model:
Version:
Type of machine:
Where applied
and what protect:
BOOK MAKING
Fitting on the material's transmission line, it
protects the packaging to be sewed from
crushing, deformation or bad positioning.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
BOOK BINDING
Protects the drive and transmission
components in the event of an overload due
to book jamming.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F
Model:
Version:
Type of machine:
Where applied
and what protect:
PRINTING MACHINE
...
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
base version
Model:
Version:
Section «F» - PAPER MACHINE
MACHINE TOOLS
Section «G»
Section «G» - MACHINE TOOLS
Type of machine:
Where applied
and what protect:
BROACHING MACHINE
Applied out from the gearbox, uphill respect
to the handling mechanism, to protect the
broaches or the tools.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version ; base version + GEC
Model:
Version:
Type of machine:
Where applied
and what protect:
SCREWERS
Applied on the motion transmission line of the
screwer's tool, it needs to screw on a fixed
torque and screw out on a higher torque.
Photo and/or drawing product:
Photo and/or drawing application:
DSR
.../SMO
Model:
Version:
Type of machine:
Where applied
and what protect:
HANDLE
Applied on the handling of handles tations
operating of machines. Protect the handle to
collision.
Photo and/or drawing product:
Photo and/or drawing application:
DSA
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
MACHINING CENTRE
It protects the handling mechanisms of the
axles and tools.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F ; DSS/F/SG
.../N ; .../N + GTR
Model:
Version:
Type of machine:
Where applied
and what protect:
MACHINING CENTER
It is applied uphill of the trasmission, it
protects the working units from accidental
collisions.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/SG
base version + GAS/CCE
Model:
Version:
Type of machine:
Where applied
and what protect:
BENDING MACHINES
Assembled on the intermediate roller, it slides
and differentiates its speed as to the other
rollers to generate the desired bending.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Section «G» - MACHINE TOOLS
MARINE ENGINEERING
Section «H»
Section «H» - MARINE ENGINEERING
Type of machine:
Where applied
and what protect:
STEAMBOAT
...
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version + Niploy
Model:
Version:
Type of machine:
Where applied
and what protect:
FITTING ON THE BOAT'S OPENABLE ROOF
Assembled on the closure / opening
mechanism. It protects the motor drive from
jamming due to foreign matters along the run.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
base version + Niploy
Model:
Version:
Type of machine:
Where applied
and what protect:
ANCHOR'S WINCHES
Assembled on the winch it protects the draft
equipment avoiding the falling of the anchor.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
.../TAS
Model:
Version:
Type of machine:
Where applied
and what protect:
RUDDER'S MOVEMENT ON THE SHIPS
Assembled on the transmission between motor
and steering. It protects the motor drive from
jamming of the steering due to foreign matters
and from counterstroke due to anomalous waves.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
... + GEC
Model:
Version:
Type of machine:
Where applied
and what protect:
MARINE ENGINEERING
Applied between motor and gear for the
control of the rudder propeller (azipod).
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
... + GAS (with jaw coupling)
Model:
Version:
Type of machine:
Where applied
and what protect:
BOAT'S MOTORIZATION
Applied along the transmission between the
motor and the propeller, it protects the motor
from jams or overloading of the propeller.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/SG
.../N + GTR (with torsionally rigid disc coupling)
Model:
Version:
Section «H» - MARINE ENGINEERING
Section «H» - MARINE ENGINEERING
Type of machine:
Where applied
and what protect:
WINCH
Applied between motor and reduction gear of
the motion of naval windlasses, it protects the
motor from overloads.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../PR ; .../TAC ; .../PR-V (with ABS certification)
Model:
Version:
Type of machine:
Where applied
and what protect:
MARINE ENGINEERING
Applied on out shaft to gearbox in order to
open/close the glass of cabin control, protect
the gear-moto.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
MOVEMENT AZIPOD
Fitted between motor and gear for azipod
orientation. Protects the motor.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
... + GAS
Model:
Version:
WOODWORKING
Section «I»
Section «I» - WOODWORKING
Type of machine:
Where applied
and what protect:
WOOD MACHINES
Applied on the handling of the conveyor belts
it protects against stoppage and disorientation
of the product.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
WOODWORKING MACHINES
Applied along the transmission between the
motor and tools. It protects the weaker
mechanical components, tools included from
excessive overloads due to accidental
stoppage.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
TILTER WOOD PANEL
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR
.../ML/TAS
Model:
Version:
Type of machine:
Where applied
and what protect:
WOOD TRANSPORT
...
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../P with grease nipples
Model:
Version:
Type of machine:
Where applied
and what protect:
CONVEYOR WOOD PANELS
Fitted on output shaft of gear-box for the
control of conveyor during the progress of
wood panels. Used as a trailing-end to protect
the material.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../TAC
Model:
Version:
Section «I» - WOODWORKING
HEAVY INDUSTRY
Section «L»
Section «L» - HEAVY INDUSTRY
Type of machine:
Where applied
and what protect:
TWIN SCREW EXTRUDER
Fitted on output shaft of gear-box. Protects
the gear-box from overload of material.
Photo and/or drawing product:
Photo and/or drawing application:
DSM
base version + GAS
Model:
Version:
Type of machine:
Where applied
and what protect:
TRASMISSION, MOVING CART FROM MINE
Fitted into a system of reduction gears.
Protects the motor against overload.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
... + GAS
Model:
Version:
Type of machine:
Where applied
and what protect:
EXTRUSION MACHINE
Fitted on output shaft of gear-box. Protects
the gear-box from overload of material.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../TAC
Model:
Version:
Type of machine:
Where applied
and what protect:
DRILLERS, DIGGERS
Applied on the shaft which moves the digged
product, it protects the gearbox from
overloading due to an accumulation of the
product.
Photo and/or drawing product:
Photo and/or drawing application:
DSR
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
STEEL INDUSTRY
Applied on drag rolls of steel bars. Slip in
function of weight for constant speed and
avoid the collision.
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
SHREDDER MACHINE
...
Photo and/or drawing product:
Photo and/or drawing application:
DSM
base version
Model:
Version:
Section «L» - HEAVY INDUSTRY
Section «L» - HEAVY INDUSTRY
Type of machine:
Where applied
and what protect:
SPREADER FLIPPER
Fitted on output shaft of gear-box. Protects
the gear-box from overloadof material.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
... + GAS
Model:
Version:
Section «L» - HEAVY INDUSTRY
AEROSPACE INDUSTRY
Section «M»
Section «M» - AEROSPACE INDUSTRY
Type of machine:
Where applied
and what protect:
MANUAL FIXTURE
Use for fitting of the wing skin to the frame to
allow tensioning without overtightening.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
.../FS
Model:
Version:
Type of machine:
Where applied
and what protect:
MACHINE FOR WING CURVE OF THE AIRPLANES
Applied at the wings bending system. Arrests
the transmission when the bending system
reaches the needed intensity.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
base version
Model:
Version:
Type of machine: AVIATION INDUSTRY: TRUCK FOR AIRCRAFT
MAINTENANCE
Fixed on axle of the actuator for moving the
truck. Protects the actuator during a trailing-
end to truck.
Photo and/or drawing product:
Photo and/or drawing application:
DSA
special base version
Model:
Version:
Where applied
and what protect:
Type of machine:
Where applied
and what protect:
FLAPS ON ULTRALIGHT AIRCRAFT
Fitted on trasmission of the control flaps. Used
to prevent shock at the helm in the case of
fast movement of the pilot
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Section «M» - AEROSPACE INDUSTRY
GENERAL APPLICATION
Section «Z»
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
STEEL INDUSTRY: CENTRIFUGAL FILTER
Fitted on the transmission of movement the
filter in order to separate liquids and the
parties voluminous. Protects the gear-box.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
MILL
Fitted on output shaft of gear-box for the
control of the mill. Used as disengagement
without water.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
... + GEC
Model:
Version:
Type of machine:
Where applied
and what protect:
MECHANICAL SECTOR: SCREWDRIVER
Fitted on head screw in order to have two
different torque in two directions of rotation.
Photo and/or drawing product:
Photo and/or drawing application:
DSR
.../SMO
Model:
Version:
Type of machine:
Where applied
and what protect:
LIFTING
Fitted in imput shaft of gear-box to limit the
rotational force that can be applied to the
jack.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
... + GAS
Model:
Version:
Type of machine:
Where applied
and what protect:
MOTOR - GEARBOX
Fitted between IEC motor and gearbox.
Protects the motor from overload.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../PR-V
Model:
Version:
Type of machine:
Where applied
and what protect:
CRUSHER FOR CONCRETE
...
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
BUILDING INDUSTRY: BRICK MARKING
It protects the weaker mechanical
components from overloads due to
accumulation of the handling material.
Photo and/or drawing product:
Photo and/or drawing application:
DSR - DSA
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
SOLID FUELS CRUSHER
Connection of Gearbox drive to crusher
roller.Protects the gear-box.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
... + GAS + swich ring
Model:
Version:
Type of machine:
Where applied
and what protect:
WATER TREATMENT
Fitted between two gearbox. Protect the gears
in case of overloads.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
.../CM + GAS
Model:
Version:
Type of machine:
Where applied
and what protect:
WATER TREATMENT: WATERS CLEANING
Applied on the motion transmission towards the
comb collector, it protect the comb from overloadings
and jams, due to excessive material to be collect.
Photo and/or drawing product:
Photo and/or drawing application:
DSR
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
WASTES DISPOSAL SYSTEMS
Applied between the motor and the
trituration system, to protect the blades when
accumulating materials or overloading.
Photo and/or drawing product:
Photo and/or drawing application:
DSR
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
PLASTIC BLOW MOLDING
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR
base version
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
MACHINES MOLDING
Applied on the injection line of the fluid
material, it intervenes and stops the
transmission when an excessive solidification
occurs.
Photo and/or drawing product:
Photo and/or drawing application:
DSR
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
AGRICULTURE SECTOR: MILLERS, HARROWS
Applied on the cardan transmission out of the
gearbox, it disengages when accumulating
material or when it jems, to protect the
gearbox and/or the cardan shaft.
Photo and/or drawing product:
Photo and/or drawing application:
DSR
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
WATER TREATMENT: MUDS EXTRACTION
Applied on the rotation axis of the roller for
muds extraction, it protects the motor from
jams due to an excessive solidification of the
muds, reducing the inertias when disengages.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/RF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
TEST BENCHES
Applied on the test axis pumps/compressors,
to protect the motor when overloading of the
group to be tested.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
... + GEC
Model:
Version:
Type of machine:
Where applied
and what protect:
TEST BENCHES
Used for the engagedisengage of different
transmissions lines, according to the group to
be tested.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
HAND DRILL
New design of drill that is electric driven
instead of traditional hydraulic , limiter is
fitted to CAM to protec drive from overload.
Photo and/or drawing product:
Photo and/or drawing application:
DF ; EDF
with gear
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
ELECTRICAL SECTOR: ASSEMBLY COMPONENT
Applied on pliers for handling of stator of the
motor. Used in order to have differt torque of
closing the pliers in function the size of the
stator.
Photo and/or drawing product:
Photo and/or drawing application:
DSF/TF/AP
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
ROTARY TABLES
Applied on the handling shaft of the table, it
protects the products when bad positioned on
the table.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N
Model:
Version:
Type of machine: PHARMACEUTICAL SECTOR: AUTOMATIC
MACHINE FOR THE PRODUCTION OF
SUPPOSITORIES IN CAVITIES
Used as a tension between the crowns of
handling bottles.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Where applied
and what protect:
Type of machine:
Where applied
and what protect:
INDEX TABLES
Applied on the handling shaft of the table, it
protects the product when bad positioned on
the table.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../N
Model:
Version:
Type of machine:
Where applied
and what protect:
INTERMITTENT DRIVE UNITS
Applied on the output shaft of the
intermittent drive unit, it protects it and the
product from casual overloadings along the
transmission line.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
TEXILE MACHINERY
...
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
.../F
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
SERVOMOTORS AND LINEAR GUIDE
Applied on the output shaft of the
servomotor, it protects it from casual
overloadings.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/SG
... + GSF
Model:
Version:
Type of machine:
Where applied
and what protect:
WORM SCREWS AND RECIRCULATING-BALL SCREWS
It is applied uphill of the srecw it protect the
motor from casual overload along the
trasmission.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/SG
... + GSF
Model:
Version:
Type of machine:
Where applied
and what protect:
ELECTRICAL SECTOR: MOBILE HEADLIGHT
Assembled on rotation axis of the headlight.
Works as stroke end sliding system to avoid
recoiling of the headlight.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
MOBILE SCAFFOLDING
Assembled on the upward motion, it slides
and avoids the rising of the scaffolding in case
of overloading.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
MULTIPURPOSE WITH DRAFT WINCH
Assembled on the winch, it protects the draft
equipment.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../C ; .../TAC
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
AUTOMATIC WAREHOUSES
Applied on the motion of the conveyor belt it
avoids overloading of the system.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
ACTUATORS AND SCREW JACKS
Protects the actuator from limit switch
impacts.
Photo and/or drawing product:
Photo and/or drawing application:
DF ; EDF
.../TA/PR-V ; .../C with LDX friction ring
Model:
Version:
Type of machine:
Where applied
and what protect:
WASHING FLOORS MACHINE
...
Photo and/or drawing product:
Photo and/or drawing application:
DF
... + GAS
Model:
Version:
Type of machine:
Where applied
and what protect:
MOVEMENT OF SOLAR PANELS
Applied at the gearboxes output shaft for the
orientation of solar panels, it protects the
gearbox against eventual stoppage.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../PR
Model:
Version:
Type of machine:
Where applied
and what protect:
MOTION FOR LIGHTING SYSTEM EQUIPMENTS
Applied between motor and gearbox of
lighting motion systems, it protects the motor.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../TAC
Model:
Version:
Type of machine:
Where applied
and what protect:
ELECTRICAL SECTOR: MANUAL DISCONNECTORS
Fitted on a manual control in the cabins
plants. Used as clutches in case of emergency
when there isn’t power.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine: ADVERTISEMENT POSTERS MECHANICALLY
CONTROLLED
Applied at the garboxes output shaft, it
protects the "single sections" of the poster in
case of jams.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
GLASS PROCESSING
Applied on the dragging roller of the glass, it
protects the dragged material in case of
collision.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../SI
Model:
Version:
Type of machine:
Where applied
and what protect:
SOLID FUEL BURNERS
Applied inside the mechanism for the coal's
crushing, it protects the machine from stress
due to material excess.
Photo and/or drawing product:
Photo and/or drawing application:
DF
bae version
Model:
Version:
Where applied
and what protect:
Type of machine:
Where applied
and what protect:
SOLID DOMESTIC BOILERS
Applied on the auger's material handling for
the progressing of the coal, it protects the
transmission from eventual obstacles.
Photo and/or drawing product:
Photo and/or drawing application:
DF
special with rigid coupling
Model:
Version:
Type of machine:
Where applied
and what protect:
ICE CRUSHER MACHINES
Applied on the motion of the ice crushing
mechanism. Protects the transmission form
vibrations and counterstrokes.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
AGRICULTURE SECTOR: FIELD IRRIGATION ROLLS
Applied at the tube recovery transmission it
slides in case of jaming to protect the draft
system.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../SI
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
AGRICULTURE SECTOR: ROUND BALE
Applied at the cardanic transmission. It slides
in case of material accumulation or jamming
to protect the product handling tools.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
HEATED KNURLING MACHINE
Applied on motor roller, it slides in function of
weight when make a knurling at constant
speed.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
STEEL INDUSTRY: TUBE CONVEYOR
Fitted on output shaft of gear-box for the
control of conveyor during the progress of the
tube. Used as a trailing-end to protect the
material.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../TAC
Model:
Version:
Type of machine:
Where applied
and what protect:
MIXING OF FOUNDRY
Applied on out shaft of gearbox to the mix
pieces of smelting, it protects the gear-motor.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../PR
Model:
Version:
Type of machine:
Where applied
and what protect:
BUILDING SECTOR
Applied in the system of adjusting speed of
sprayer the cement. Slip when clogged the
sprayer and protect the pump.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../SI
Model:
Version:
Type of machine:
Where applied
and what protect:
EXTRUDER (CHEWING-GUM MACHINE)
Screwjack in extruder application to protect
screwjack in event of peak torque.
Photo and/or drawing product:
Photo and/or drawing application:
DSS
base version
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
PUBLIC TOILETS
Fitted output of Gearbox to tilt floor during
wash cycle, allows the floor to remain static if
persons are still inside.
Photo and/or drawing product:
Photo and/or drawing application:
DF
... + GAS
Model:
Version:
Type of machine:
Where applied
and what protect:
CABIN FOR TANNING
...
Photo and/or drawing product:
Photo and/or drawing application:
DSS/SG
.../N
Model:
Version:
Type of machine:
Where applied
and what protect:
FOOD SECTOR: INDUSTRIAL DISHWASHER
Applied on output shaft of gear-box for the
transport of baskets of industrial dishwashers.
Protects the gear-box.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
FOOD SECTOR: INDUSTRIAL DISHWASHER
Applied on output shaft of gear-box for the
movement of rotating the industrial
dishwasher basket. Protect the gear-box.
Photo and/or drawing product:
Photo and/or drawing application:
DF
.../TAC
Model:
Version:
Type of machine:
Where applied
and what protect:
CLEANING GLASS BUILDINGS
Fitted on output shaft of gear-box for
horizontal movement of the scaffolding. Used
as a trailing-end to protect the gear-box.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
MOTOR - GEARBOX
Fitted between IEC motor and gearbox.
Protects the motor from overload.
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
.../PR-V
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
Type of machine:
Where applied
and what protect:
WINCH FOR REEL/UNREEL OF UMBILICAL LINE
Fitted on shaft winder. Protects the gear-box
from overload in case of excessive torque if
umbilical is trapped during winding.
Photo and/or drawing product:
Photo and/or drawing application:
DSR/F
... + GEC
Model:
Version:
Type of machine:
Where applied
and what protect:
MECHANICAL SECTOR: CHIPS TRITURATOR
Connection angular gear-box.
Photo and/or drawing product:
Photo and/or drawing application:
DF
special .../CR (with radial bearing)
Model:
Version:
Type of machine:
Where applied
and what protect:
BOARD BILLBOARD
Fitted on output shaft of gear-box to control
the billboard.
Photo and/or drawing product:
Photo and/or drawing application:
DF
base version
Model:
Version:
Type of machine:
Where applied
and what protect:
WATER TREATMENT
Fitted on the transmission of movement the
filter in order to separate liquids and the
parties voluminous. Protects the gear-box.
Photo and/or drawing product:
Photo and/or drawing application:
EDF/F
.../F ; .../TAC
Model:
Version:
Type of machine:
Where applied
and what protect:
FILLING MACHINE
...
Photo and/or drawing product:
Photo and/or drawing application:
DSS/F/SG
special version .../AP
Model:
Version:
Type of machine:
Where applied
and what protect:
FOOD SECTOR: EXTRUDERS FOR PASTA
Fitted on output shaftof gear-box. Protects the
gear-box from overload of material
Photo and/or drawing product:
Photo and/or drawing application:
DSM
... + GAS
Model:
Version:
Section «Z» - GENERAL APPLICATION
Section «Z» - GENERAL APPLICATION
ASK FOR A PROJECT
Your needs are our priorities.
If you need help for a product design, contact ComInTec experts for assistance and advice. It helps to fill in this
form. Your request will be handled in the shortest time possible.
General information:
Company name: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
City / State: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Name / Surname: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Title: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Phone: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
E-mail / website: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Quantity: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Planned yearly quantities: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Target price: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use:
OEM name / website: __________________________________________________
Application field / type of machine: __________________________________________________
Where it's applied and what it protects: __________________________________________________
Model currently used: __________________________________________________
Nominal torque (Nm): __________________________________________________
Speed (Rpm): __________________________________________________
Workplace:
Clean
Dusty
Oily
Humid / Wet
Other _______________________________________________________________
ASK FOR A PROJECT
Re-engagement position:
Equidistant
360°
Not important
Other _______________________________________________________________
Electric signal of overload required:
Yes
No
Transmission:
Parallel
In line
Driving shaft diameter (mm): ____________________________________________
Driving shaft connection type:
Keyway
Locking assembly
Spline (specification: ____________________________________________________)
Other _______________________________________________________________
Type of drive component e.g sprocket, gear etc. (parallel transmission):
____________________________________________
Type of coupling (in line transmission): ____________________________________________
Driven shaft diameter (mm): ____________________________________________
Driven shaft connection type:
Keyway
Locking assembly
Spline (specification: ____________________________________________________)
Other _______________________________________________________________
Notes: _____________________________________________________________________________
_______________________________________________________________________________________
_______________________________________________________________________________________
Autoriz D.lgs. 196/2003ation
Signature
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
PLEASE ALSO SEND, IF AVAILABLE, A DRAWING OR PHOTOGRAPH. IT CAN ASSIST US
ENORMOUSLY IN HELPING US TO FULLY UNDERSTAND YOUR APPLICATION.
Send to tecnico@comintec.it or by fax +39 051 782256 (Att. Technical Department)
ComInTec srl - Via Dell'Artigiano, 9 - 40055 Villanova di Castenaso - BOLOGNA - Tel. +39 051 780216 - Fax +39 051 782256 - info@comintec.it - www.comintec.it
PRODUCT PROGRAMME:
TORQUE LIMITERS
CLUTCHES
ELASTOMERIC COUPLINGS - RIGID COUPLINGS
LOCKING RINGS
VARIABLE SPEED PULLEYS - MOTOR SLIDE BASES
Ed
itio
n 0
7/2
01
3
top related