wire connections for multi-cassette€¦ · wire connections for multi-cassette delarue®...

Wire Connectionsfor Multi-Cassettefor Multi Cassette

DeLaRue® Dispensers

Innovative Control Systems1349 Jacobsburg Road • Wind Gap, PA 18091

610.881.8000 • 610.881.8120 – fax • www.washnet.com

Before You BeginBefore You Begin

• Always turn the power to the unit off • Always turn the power to the unit off before you begin.Have someone available to help you lift • Have someone available to help you lift the bill dispenser if necessary.A lifi d ICS t h i i h l • A qualified ICS technician can help ensure these instructions are followed correctly. C t t ICS f tContact ICS for support.

3/18/2009 2

Required ToolsRequired Tools

• Hex wrench to open the Auto Sentry flex • Hex wrench to open the Auto Sentry flex side chamber.T10 Torx® driver• T10 Torx® driver.

3/18/2009 3

Preparing a Work SurfacePreparing a Work Surface

• Prepare a clean solid work surface on • Prepare a clean, solid work surface on which to position the bill dispenser.Work surface should be dry protected • Work surface should be dry, protected and free from debris.D t tt t t th b d • Do not attempt to use the bare ground as a work surface.

3/18/2009 4

Removing the DispenserRemoving the Dispenser

• Open side • Open side chamber on unit.Extend tray• Extend tray.

• Access wiring.

3/18/2009 5

Removing the DispenserRemoving the Dispenser

• Disconnect power• Disconnect power.

3/18/2009 6

Removing the DispenserRemoving the Dispenser

• Disconnect COM• Disconnect COM.

3/18/2009 7

Removing the DispenserRemoving the Dispenser

• Disconnect ground• Disconnect ground.

3/18/2009 8

Removing the DispenserRemoving the Dispenser

• Unclip harness• Unclip harness.

3/18/2009 9

Removing the DispenserRemoving the Dispenser

• Lift dispenser off tray• Lift dispenser off tray.• Place dispenser on secure work surface.

3/18/2009 10

Removing the PlateRemoving the Plate

• Orient dispenser as shown• Orient dispenser as shown.• Locate top cover.

L • Locate screw.

3/18/2009 11

Removing the PlateRemoving the Plate

• Use T10 Torx driver• Use T10 Torx driver.• Remove screw.

R i i• Remove cover to expose wiring.

3/18/2009 12

Connecting the WiresConnecting the Wires

• Locate disconnected wires• Locate disconnected wires.

3/18/2009 13

Connecting the WiresConnecting the Wires

• Connect wires• Connect wires.– Smaller head is keyed. Fits only one way.– Larger head fits with wires facing down.– Do not force.

3/18/2009 15

Connecting the WiresConnecting the Wires

• Use T10 Torx driver• Use T10 Torx driver.• Replace cover.

D t i h i b th – Do not pinch wires beneath cover.

3/18/2009 17

Replace Bill DispenserReplace Bill Dispenser

Reseat & secure bill dispenser on trayReseat & secure bill dispenser on tray.Reconnect wires.R li hReclip harness.Close & lock door.Test.

3/18/2009 18

• Information in this presentation is subject to change without notice. Companies, names and data used in examples within the presentation are fictitious unless names and data used in examples within the presentation are fictitious unless otherwise noted. No part of this presentation may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Innovative Control Systems, Inc.

• ICS is not responsible for damage, bodily harm, loss of business, etc. due to the information contained in this document. Refer to the standard sales agreement and warranty information that came with your ICS product for more details.

• Auto Sentry, Lube Master and Tunnel Master are registered trademarks of Innovative Control Systems, Inc.

• Touch ‘N Clean and Wash Valet are trademarks of Innovative Control Systems, Inc.• DeLaRue is a registered trademark of De la Rue Holdings plc• DeLaRue is a registered trademark of De la Rue Holdings, plc• Torx is a registered trademark of Acument Intellectual Properties, LLC LTD.

3/18/2009 19Copyright © 2009 Innovative Control Systems, Inc.