amplificador portátil decómo encender el amplificador cómo encender la esfera de luz led presione...
TRANSCRIPT
Amplificador portátil de 125 W PMPO con esfera de luz LED
V0.0 / 0517vMANUAL DE INSTRUCCIONES
2
AMP-009 / AMP-009BTAntes de utilizar el producto, lea cuidadosamente este instructivo para evitar cualquier
mal funcionamiento.La información presentada sirve únicamente como referencia sobre el producto. Debido a actualizaciones pueden existir diferencias. Consulte nuestra página web www.steren.com
para obtener la versión más reciente de este manual.
PRECAUCIONES
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Este producto NO es un juguete; manténgalo fuera del alcance de los niños.
Cualquier reparación no autorizada puede ocasionar mal funcionamiento y anulará la garantía.
No utilice líquidos abrasivos para limpiar el amplificador.
No use ni almacene el equipo en lugares donde existan goteras y salpicaduras.
3
CONTENIDO
Amplificador
Convertidor de voltaje Correa
Cable cannon / 6,3 mm
Micrófono (Sólo AMP-009BT)
Control remoto
4
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
DESCRIPCIÓN GENERAL DEL AMPLIFICADOR (AMP-009)
Panel frontal
1. Esfera de luz
2. Módulo de reproducción
3. Controles de volumen
4. Entrada auxiliar
5. LED indicador de carga
6. Entrada de alimentación
7. Entrada 6,3 mm para micrófono
8. Ranura para tarjeta SD
5
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
DESCRIPCIÓN GENERAL DEL AMPLIFICADOR (AMP-009BT)
Panel frontal
1. Esfera de luz
2. Módulo de reproducción
3. Controles de volumen
4. Entrada auxiliar
5. LED indicador de carga
6. Entrada de alimentación
7. Entrada 6,3 mm para micrófono
8. Ranura para tarjeta SD
9. Puerto USB
6
DESCRIPCIÓN GENERAL DEL AMPLIFICADOR (AMP-009BT / AMP-009)
Panel lateral
Interruptor de encendido / apagado
Interruptor de encendido / apagado para luces LED
7
CONTROLES DE VOLUMEN
Volumen maestro
Volumen del micrófono
Volumen de eco del micrófono
MIC.VOL
ECHO
8
MÓDULO DE REPRODUCCIÓN (AMP-009)
MÓDULO DE REPRODUCCIÓN (AMP-009BT)
1. Pantalla2. Receptor IR3. Cambio de modo de reproducción (SD / Auxiliar)4. Pista anterior / Disminuir volumen**5. Pausar / reproducir6. Pista siguiente / Aumentar volumen**7. Ranura para tarjeta SD
1. Pantalla2. Receptor IR3. Cambio de modo de reproducción (SD /USB /Bluetooth /Radio FM / Auxiliar)4. Pista anterior / Estación FM anterior / Disminuir volumen**5. Pausar / reproducir / Búsqueda automática de estaciones FM6. Pista siguiente / Estación FM siguiente / Aumentar volumen**7. Ranura para tarjeta SD8. Puerto USB
** Mantenga presionado
** Mantenga presionado
9
CONTROL REMOTO
1. Silencio
2. Cambiar modo de reproducción (SD y Auxiliar / Bluetooth, Radio FM y USB-Solo para el modelo AMP-009BT)
3. Repetir pistas (ALL: todas /Fold: una carpeta /One: una pista/ rAn: aleatorio
4. Pista siguiente / Estación FM siguiente (FM Solo para el modelo AMP-009BT)
5. Pista anterior / Estación FM anterior (FM Solo para el modelo AMP-009BT)
6. Volumen + / Volumen -
7. Reproducir grabación
8. Grabar
9. Selección directa de pista
10. Ecualizador
11. Reproducir/Pausar /Búsqueda automática de estaciones FM (FM Solo para el modelo AMP-009BT)
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
Para controlar la reproducción a distancia,apunte el control remoto hacia la partefrontal del amplificador.
10
CONEXIONES (AMP-009)
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
11
CONEXIONES (AMP-009BT)
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
12
ANTES DE EMPEZAR
Opciones de alimentación
Opción 1: Con el convertidor de voltaje
Elija alguna de las siguientes opciones para proporcionarle energía al amplificador:
Opción 2: Con la batería recargable
Antes de utilizar el amplificador por primera vez con la batería recargable, conéctelo con el convertidor de voltaje durante 12 horas continuas. Para cargarlo las siguientes veces, déjelo conectado hasta que el LED indicador de carga permanezca encendido en color azul.
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
13
Cómo encender el amplificador
Cómo encender la esfera de luz LED
Presione el interruptor de encendido / apagado.
Presione el interruptor de encendido / apagado para luces LED.
14
OPCIONES DE REPRODUCCIÓN
Conexión Bluetooth (Solo para el modelo AMP-009BT)
Memoria SD / USB (USB Solo para el modelo AMP-009BT)
Radio FM (Solo para el modelo AMP-009BT)
Auxiliar
Inserte una memoria SD o USB (USB sólo para el modelo AMP-009BT) con archivos MP3 en el puerto correspondiente.La reproducción comenzará automáticamente
Presione el botón MODE en el módulo o en control remoto para cambiar a modoradio FM.Consulte la sección “Módulo de reproducción” y “Control remoto” para ver cómo cambiar las estaciones de radio.
1. Inserte un cable en el conector AUX INPUT.
2. Presione MODE en el módulo de reproducción o en el control remoto paracambiar de modo. En el display debe aparecer la leyenda LInE
Inice y controle la reproducción en su equipo.
1. Presione el botón MODE en el módulo o en control remoto para cambiar a modo Blue-tooth. En la pantalla, la leyenda “bLUE” encenderá y apagará continuamente.2. Ingrese a las opciones de Bluetooth en el dispositivo que desea vincular.3. Busque y seleccione Steren AMP-009. Si la vinculación es exitosa, la leyenda “bLUE” en la pantalla permanecerá fija.4. Inicie la reproducción desde el dispositivo.
15
GRABACIÓN
1. Inserte una memoria SD o USB (USB Solo para el modelo AMP-009BT) con al menos un archivo MP3.2. Conecte y encienda el micrófono.3. Encienda el amplificador.4. Presione una vez el botón RECO en el control remoto para empezar a grabar. En el display aparecerá la leyenda rEC. Presione nuevamente el botón para detener la graba-ción (ésta se reproducirá inmediatamente).
Si desea reproducir las grabaciones posteriormente presione PLAYRECO en el control remoto.
Reemplazar la batería del control remotoInserte una batería CR2025 con la polaridad como se muestra en la imagen.
16
ESPECIFICACIONES
Alimentación: 9 V - - - 2 APotencia: 10 WrmsBatería: 7,4 V - - - 2 AhRespuesta en frecuencia: 40 Hz - 15 kHzTamaño de woofer: 4,5”Tamaño de tweeter: 1”Consumo: 12 W/hConsumo en reposo: 3 W/h
Convertidor de voltaje
Alimentación: 100 - 240 V ~ 50/60 Hz 0,5 ASalida: 9 V - - - 2 A
Las especificaciones pueden cambiar sin previo aviso
17
125 WPMPO PORTABLE AMPLIFIER WITH LED LIGHT
V0.0 / 0517v USER MANUAL
18
AMP-009 / AMP-009BTBefore to use the product, please read carefully this manual to avoid any malfunction. The info in this manual is shown as reference. Due to updates can exist differences.
Consult our website www.steren.com to obtain the current version of this manual.
CAUTIONS
The operation of this equipment is subject to the following two conditions: (1) it is possible that this equipment or device may not cause harmful interference and (2) this equipment or device must accept any interference, including interference that may cause its undesired operation
This product is NOT a toy; keep it away from children.
Any reparation not authorized may cause malfunction and avoid the warranty.
Don’t use abrasive liquids to clean it.
Don’t use or store the device in places where exist water or splashes.
19
CONTENT
Amplifier
AC adapter Belt
Cannon / 6.3 mm cable
Microphone (only for AMP-009BT)
Remote control
20
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
GENERAL DESCRIPTION OF THE AMPLIFIER (AMP-009)
Frontal panel
1. Light sphere
2. Playback module
3. Volume controls
4. Auxiliary input
5. Charge indicator LED
6. Power input
7. 6.3 mm to microphone
8. SD card slot
21
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
GENERAL DESCRIPTION OF THE AMPLIFIER (AMP-009BT)
Frontal panel
1. Light sphere
2. Playback module
3. Volume controls
4. Auxiliary input
5. Charge indicator LED
6. Power input
7. 6.3 mm to microphone
8. SD card slot
9. Puerto USB
22
GENERAL DESCRIPTION OF THE AMPLIFIER (AMP-009BT / AMP-009)
Side panel
On / off switch
LED lights on / off switch
23
VOLUME CONTROLS
Master volume
Microphone volume
Microphone echo volume control
MIC.VOL
ECHO
24
PLAYBACK MODULE (AMP-009)
MÓDULO DE REPRODUCCIÓN (AMP-009BT)
1. Sceen2. IR receiver3. Playback mode change (SD / Auxiliar)4. Previous track / volume -**5. Pause / play6. Next track / volume +**7. SD card slot
1. Screen2. IR receiver3. Playback mode change (SD /USB /Bluetooth / FM radio / Auxiliary)4. Previous track / FM previous station / volume -**5. Pause / play / FM stations automatic search6. Next track / FM next station / volume +**7. SD card slot8. USB port
** Mantenga presionado
** Mantenga presionado
25
REMOTE CONTROL
1. Mute
2. Playback mode change (SD and Auxiliary /Bluetooth ,FM radio and USB only for AMP-009BT)
3. Repeat (ALL: /Folder /One/rAn: random)
4. Next track / FM next station( only for AMP-009BT)
5. Previous track / FM previous station (FM only for AMP-009BT)
6. Volume + / Volume -
7. Play recoerding
8. Recording
9. Track selection
10. Equalizer
11. Play /Pause / FM stations automatic search (FM only for AMP-009BT)
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
To control the playback, aim the remote control to the front panle of the amplifier.
26
CONNECTIONS (AMP-009)
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
27
CONNECTIONS (AMP-009BT)
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
28
BEFORE TU USE
Power options
Option 1: With AC adapter
Choose some the next options to give power to the amplifier:
Option 2: With the rechargable battery
Before to using the amplifier for first time with the rechargeable battery, connect ot with the AC adapter for 12 continuous hours. To charge it in the next times, leave it connected until the charge indicator LED remains turn on in blue color.
The battery life is 4 hours approx.
MIC/GT.INPUT ECHO MIC.VOLDC9V 1.5A
Charagelamp
29
How to turn on the amplifier How to turn on the LED light sphere
Press the on / off switch Press the on / off switch for LED lights.
30
PLAYBACK OPTIONS
Bluetooth connection (Only for AMP-009BT)
SD / USB memory (USB only for AMP-009BT)
FM radio (Only for AMP-009BT)
Auxiliary
1. Insert a SD or USB memory with MP3 audio files.
The playback starts automatically.
Press the MODE button in the module or in the remote control to change FM radio mode.
Consulting the section “Playback module” and “Remote control” to know how change the FM radio stations.
1. Insert a cable into AUX INPUT connector.
2. Press MODE in the playback module or in the remote control to change the mode. In the screen must be appears the message Line.
Start the playback form your device.
1. Press the MODE button in the module or in the remote control to change the Bluetooth mode. In the screen, the message “bLUE” will flash continuosly.2. Enter the Bluetooth options in the mobile device that you wan to pair.3. Search and select Steren AMP-009. If the pairing is successful, the message “bLUE” remains fixed.4. Start the playback form your device.
31
RECORDING
1. Insert a SD or USB memory (USB only for AMP-009BT) with at least one a MP3 audio file.2. Connect and turn on the microphone.3. Turn on the amplifier.4. Press once RECO in the remote control to start the recording. In the screen appears the message rEC. Press again the same button to stop the recording, (this will playing immediately).
If you want to play the record later, play PLAYRECO in the remote control.
Replacement of the battery in the remote controlInsert a CR2025 battery with the polarity as shown below.
32
SPECIFICATIONS
Input: 9 V - - - 2 APower output: 10 WrmsBattery: 7.4 V - - - 2 AhFrequency response: 40 Hz - 15 kHzWoofer size: 4.5”Tweeter size: 1”Consumption: 12 W/hStand-by power consumption: 3 W/h
Power converter
Input: 100 - 240 V ~ 50 / 60 Hz 0.5 AOutput: 9 V - - - 2 A
Specifications may change without notice
33