Completed Assembly

Apply Decal

3

Assembly Sequence

RECOMMENDED PAINT COLORS

SYMBOLS

AluminumGloss Black

SilverSemi-Gloss BlackSemi-Gloss Grey

Flat BlackWhite

Part Number49

1/25 SCALE

A756-200

DECALS: See back of instruction sheet for application instructions. Many of the very small decals in this kit have been included in duplicate to serve as backups, should any get lost or otherwise compromised during application.

REFER TO BOX ART PHOTOS FOR PAINTING DETAILS

1. DETAILING DECALS

DECALS MUST BE APPLIED TO CERTAIN PARTS AFTER PAINTING BUT PRIOR TO ASSEMBLY. SEE SECTION 1.

5. BODY

6. FINAL ASSEMBLY

BLACK METAL SCREWS (4)

20RIGHT FOG

LIGHT BEZEL

19LEFT FOG

LIGHT BEZEL

32LEFT FOG

LIGHT LENS(Clear)

31RIGHT FOG LIGHT LENS

(Clear)

9HOOD

8REAR FASCIA

28

30

29

27

TAILLIGHT LENSES (4) (Clear)

14LEFT MIRROR

15RIGHT MIRROR

23WINDSHIELD (Clear)

7FRONT FASCIA

18RIGHT LIGHT

UNIT

1COUPEBODY

26RIGHT HEADLIGHT

LENS (Clear)

25LEFT HEADLIGHT

LENS (Clear)

Carefully install completed chassis/interior assembly into completed body. Ensure chassisis fully seated, then using a small Phillips screwdriver, install screws into the 4 locations shown.

IMPORTANT: Apply decals to seats, dashboard and steering wheel BEFORE assembling parts in Section 3/INTERIOR.BE SURE TO PAINT THE DESIRED PARTS FIRST AND ALLOW THEM TO DRY FULLY BEFORE APPLYING DECALS.DECAL

DECALS: See back of instruction sheet for application instructions. All decals have been included in duplicate to serve as backups, should any get lost or damaged during application.

10 STEERING WHEEL 12 DASHBOARD

SEATS (Vinyl)

(HVAC DECAL)

OPTIONS

17LEFT LIGHT UNIT

(Repeat for other side.)

NOTE: Locate holes in top of windshield to pins inside roof of body.

Apply Corvette® emblem decals to front and rear fascias, as shown. Apply GM logo decals to rear quarter panels using box art photos for placement detail. Apply your choice of rear license plate decal.

NOTE: Open sides of fog light bezels face out.

20122012

(Other side.)

(Other side.)

GENERAL MOTORS Trademarks used under license to Round 2, LLC. AMT is a registered trademark. ©2011. All rights reserved. Round 2 & design is a trademark of Round 2, LLC. ©2011 Round 2, LLC, South Bend, IN 46628 USA. Product and packaging designed in the USA. Made in China. All rights reserved.

Round 2, LLC 4073 Meghan Beeler CourtSouth Bend, IN 46628

International Hobbycraft (UK) Ltd.21 St. Thomas StreetBristol BS1 6JS England

DECAL APPLICATION INSTRUCTIONS1. Cut decals apart close to image. Apply one at a time.2. Dip decal into tepid water until paper backing loosens.3. Moisten area of model where decal is to be applied, to aid in positioning.4. Slide decal partly off of paper backing.5. Place decal on model face up and slide paper backing away.6. Thoroughly blot out excess water, air bubbles, and any excess emulsion with soft, lint-free cloth.7. Allow time to dry before handling.

NOTE: If air bubbles or wrinkles form on an irregular or curved surface, cut decal and press into place.

Decal

Paper Backing

DECAL

1

DECAL

1

DECAL

8

DECAL

9

DECAL

17DECAL

10

DECAL

DECAL

12

DECAL

10

DECAL

11

DECAL

13

DECAL

16

DECAL

14DECAL

15

DECAL

2DECAL

3

DECAL

4

DECAL

5

IMPORTANT

Assembly: Carefully study and understand the entire instruction sheet. Compare the parts in the box to the instruction sheet to be sure you have received all the parts required. Carefully remove parts from trees. Before cementing, "TEST FIT" parts together to insure proper location and alignment. Scrape paint and plating from surfaces to be cemented. Subassemblies and components should be painted before any parts are attached. Use only cement and paint made for styrene plastic.

Painting: Wash parts thoroughly with mild soap and water. Parting lines, glue joints, and sharp edges should be sanded or filled with filler putty designed for plastic. Apply a "primer" coat and allow to dry. Check parts for imperfections and repeat the procedure if necessary. Remove any lint or dust. Apply paint evenly, in several thin coats rather than one heavy coat. Allow each coat to thoroughly dry before the next is applied. Each coat should be carefully “wet sanded” using slightly damp No. 1200 sandpaper. Be careful not to remove any detail while sanding. Lightest colors should be painted first. Use frosted tape to mask off areas not to be painted. Remove tape after paint is dry to the touch. Use a very fine brush to touch up edges.

Decals: See back of instruction sheet for proper application. Decals should to be added after applying a gloss coat. Apply a final clear coat after decals are dry.

2. WHEELS & CHASSIS

4. INTERIOR TO CHASSIS

37RIGHT FRONT DISC BRAKE 39

RIGHT REAR DISC BRAKE

36LEFT FRONT DISC BRAKE

38LEFT REAR DISC BRAKE

16EXHAUST TIPS (2)

21FRONT WHEEL (Chrome)

21FRONT WHEEL (Chrome)

22REAR WHEEL (Chrome)

(LARGE / WIDE)

22REAR WHEEL (Chrome)

(LARGE / WIDE)

IMPORTANT: Apply decals to seats, dashboard and steering wheel as shown in SECTION 1, before assembling parts.

METAL AXLE METAL AXLE

TAB

REAR TIRE (LARGE / WIDE)FRONT TIRE (SMALL)

FRONT TIRE (SMALL)REAR TIRE (LARGE / WIDE)

CHASSIS SHOWN UPSIDE DOWN

NOTE: Work completed wheels firmly onto axles.

NOTE: Wheels not shown for clarity.

Locate interior to chassis by inserting pins on top side of chassis into large bosses in bottom of interior.

NOTE: Ensure correct disc brake part numbers are used for each wheel. Each disc brake has a tab which locks into the chassis, to position its caliper correctly. Apply cement to tabs only, so that axles may rotate inside.

TAB

TAB TAB

10

11

NOTE: To make the tires easier to stretch, run them under very warm water for 30 seconds. BE CAREFUL NOT TO BURN YOUR HANDS.

Stretch tire over wheel making sure it is fully seated.

10STEERING

WHEEL

11COLUMN

12DASHBOARD

4FLOOR PAN

SEATS (2) (Vinyl)

5LEFT DOOR PANEL

6RIGHT DOOR PANEL

NOTE: Locate tab on bottom ofdashboard to slot at front of

floorboard tunnel.

13SHIFTER

KNOB(To hole)

3. INTERIOR

2(Completed Chassis)

3(Completed Interior)

DECAL

6

DECAL

7