analog basics workshop getting started with tina-ti rev 0.2
TRANSCRIPT
![Page 1: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/1.jpg)
Analog Basics WorkshopGetting started with Tina-
TI
Rev 0.2
![Page 2: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/2.jpg)
Tina-TI is a powerful Analog and SMPS circuit simulation tool
Screenshot of TinaTM output
graphics
![Page 3: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/3.jpg)
Tina-TI schematic editor
Circuit Space
Top row:Operations associated with files, types of analysis,test & measurement options, and help
Second row:File operations, text, hide andwiring feature selection, etc.
Third & fourth rows:Third row buttons select component typeForth row tabs select component group
![Page 4: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/4.jpg)
Building a circuit in Tina-TI
Wein-bridge 1kHz oscillator
1. Select the “Spice Macros” tab.
2. Click on the op-amp symbol.
3. The op-amp list opens. Select OPA743.
4. U1 – OPA743 symbol appears. Drag symbol into position.
5. Other op-amp models may be selected using insert > macro…
12
34
5
Passive and active components are selected from symbols and lists
![Page 5: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/5.jpg)
Adding passive and
active components
1. Select the “Basic” tab
2. Click on the desired passive component, source, jumper, generator, ground, etc.
3. Drag the selection into place. Click to set in position.
4. Double click on the selected component. An information table appears.
5. Enter the value and set the parameters as needed.
12
3
4
5
Jumpers are used to connect commoncircuit points without adding wires
Building a circuit in Tina-TI
![Page 6: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/6.jpg)
Arrange and wiring components
1. Arrange the components by clicking on the symbol and dragging them into position.
2. Start wiring components together by placing the pointer over the end node (small red “x”).
3. Click on the end node and a wire is drawn as the mouse is moved.
4. Release the mouse button to end a wire at another node.
5. Wiring function may be activated using “Insert” > wire, or the radio button pencil symbol.
5
2
Building a circuit in Tina-TI
![Page 7: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/7.jpg)
Analysis Capabilities: DC
Performing a DC analysis
1. Click on “Analysis.”
2. Highlight and click on “DC Analysis.”
3. Click on “Calculate nodal voltages.”
4. The Voltages/Currents are displayed at meters/probes.
5. The mouse pointer becomes a probe used to probe the circuit nodes.
6. The probed node and measured value are shown in red, in the table.
12
AEW-Tina-Intro.TSC
![Page 8: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/8.jpg)
Analysis Capabilities: Transient
1. Click on “Analysis”2. Highlight and click on “Transient”3. Set start and end times, etc.4. Click “ok”5. Transient analysis from simulation.
1 2
3
4
5
Transient Analysis example
![Page 9: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/9.jpg)
Analysis Capabilities: AC Transfer Characteristics
1. Click on “Analysis> Transient”2. Set freq range, etc. Click “ok”3. Transient analysis from simulation.
1
2 3
AEW-Tina-Intro.TSC
![Page 10: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/10.jpg)
Where to find Tina-TI Help
Many of Tina’s component and Analysis Windows provide a Help button
Select to get Helpon this subject
Help sheeton subject
Help contents, searches, etc
![Page 11: Analog Basics Workshop Getting started with Tina-TI Rev 0.2](https://reader036.vdocuments.net/reader036/viewer/2022081414/5513fe0f550346e2488b476c/html5/thumbnails/11.jpg)