analysis of idealized tropical cyclone simulations using
TRANSCRIPT
Analysis of Idealized Tropical Cyclone Simulations Using the Weather Research andForecasting Model: Sensitivity to Turbulence Parameterization and Grid Spacing
KEVIN A. HILL AND GARY M. LACKMANN
Department of Marine, Earth and Atmospheric Sciences, North Carolina State University, Raleigh, North Carolina
(Manuscript received 12 April 2007, in final form 2 January 2008)
ABSTRACT
The Weather Research and Forecasting Advanced Research Model (WRF-ARW) was used to perform
idealized tropical cyclone (TC) simulations, with domains of 36-, 12-, and 4-km horizontal grid spacing.
Tests were conducted to determine the sensitivity of TC intensity to the available surface layer (SL) and
planetary boundary layer (PBL) parameterizations, including the Yonsei University (YSU) and Mellor–
Yamada–Janjic (MYJ) schemes, and to horizontal grid spacing. Simulations were run until a quasi-steady
TC intensity was attained. Differences in minimum central pressure (Pmin) of up to 35 hPa and maximum
10-m wind (V10max) differences of up to 30 m s21 were present between a convection-resolving nested
domain with 4-km grid spacing and a parent domain with cumulus parameterization and 36-km grid spacing.
Simulations using 4-km grid spacing are the most intense, with the maximum intensity falling close to
empirical estimates of maximum TC intensity. Sensitivity to SL and PBL parameterization also exists, most
notably in simulations with 4-km grid spacing, where the maximum intensity varied by up to ;10 m s21
(V10max) or ;13 hPa (Pmin). Values of surface latent heat flux (LHFLX) are larger in MYJ than in YSU at the
same wind speeds, and the differences increase with wind speed, approaching 1000 W m22 at wind speeds in
excess of 55 m s21. This difference was traced to a larger exchange coefficient for moisture, CQ, in the MYJ
scheme. The exchange coefficients for sensible heat (Cu) and momentum (CD) varied by ,7% between the
SL schemes at the same wind speeds. The ratio Cu/CD varied by ,5% between the schemes, whereas CQ/CD
was up to 100% larger in MYJ, and the latter is theorized to contribute to the differences in simulated
maximum intensity. Differences in PBL scheme mixing also likely played a role in the model sensitivity.
Observations of the exchange coefficients, published elsewhere and limited to wind speeds ,30 m s21,
suggest that CQ is too large in the MYJ SL scheme, whereas YSU incorporates values more consistent
with observations. The exchange coefficient for momentum increases linearly with wind speed in both
schemes, whereas observations suggest that the value of CD becomes quasi-steady beyond some critical wind
speed (;30 m s21).
1. Introduction
It has been shown that improvements in the accuracy
of tropical cyclone (TC) intensity predictions continue
to lag improvements in track prediction (e.g., Knaff
et al. 2003; DeMaria et al. 2005; Rogers et al. 2006). This
discrepancy is in part due to the fact that numerical
models are able to provide reliable track guidance even
when the intensity forecast from the same model is in-
accurate, provided that the synoptic-scale steering flow
is reasonably well depicted. The lack of accuracy in
numerical intensity forecasts from operational dynami-
cal models is attributable to several factors, including
but not limited to (i) poor representation of TCs in
model initial conditions (e.g., Kurihara et al. 1995, 1998;
Xiao et al. 2000; Zou and Xiao 2000; Aberson 2003), (ii)
inaccuracies in model representation of processes tak-
ing place near the air–sea interface (e.g., Emanuel 1995;
Andreas and Emanuel 2001; Braun and Tao 2000; Per-
rie et al. 2005), and (iii) model resolution (e.g., Braun
and Tao 2000; Davis and Bosart 2002; Persing and
Montgomery 2003). The resolution sensitivity is linked
to a growing body of evidence that small-scale vortices
in and near the eyewall can alter TC thermodynamics
sufficiently to change intensity (e.g., Persing and Mont-
gomery 2003; Braun et al. 2006; Gentry 2007; Cram et
al. 2007; Yang et al. 2007). In this study, we will use the
Weather Research and Forecasting Advanced Research
Model (WRF-ARW) to examine factors ii and iii above,
Corresponding author address: Kevin A. Hill, Department of
Marine, Earth and Atmospheric Sciences, North Carolina State
University, 1125 Jordan Hall, Raleigh, NC 27695-8208.
E-mail: [email protected]
FEBRUARY 2009 H I L L A N D L A C K M A N N 745
DOI: 10.1175/2008MWR2220.1
� 2009 American Meteorological Society
while eliminating consideration of i by utilizing ideal-
ized simulations of long duration.
Tropical cyclones intensify and maintain themselves
against dissipation by extracting energy from the ocean
(e.g., Byers 1944; Emanuel 1986); therefore numerical
model simulations of TCs are highly sensitive to the
parameterization of energy transfer processes at the
air–sea interface (e.g., Ooyama 1969). Numerical mod-
els calculate the air–sea exchange of heat, moisture, and
momentum using a surface layer (SL) parameterization
scheme, and estimate turbulence-induced tendencies of
momentum and thermodynamic quantities using a
planetary boundary layer (PBL) scheme. The validity
of current model SL parameterizations in TC environ-
ments is questionable, owing to their empirical nature
and the lack of observational data taken at high wind
speeds over water (e.g., Large and Pond 1981; Emanuel
1995; Braun and Tao 2000; Powell et al. 2003; Perrie et
al. 2005). Recent field observations, such as those taken
during the Coupled Boundary Layers/Air–Sea Transfer
(CBLAST) experiment (Black 2004; Black et al. 2007),
suggest that linear extrapolation of exchange coeffi-
cients from those based on low wind speed measure-
ments, as done in current SL schemes, is incorrect. PBL
parameterization schemes also impact simulated TC in-
tensity, but typically to a lesser extent than SL schemes
(Braun and Tao 2000). To assess simulated TC sensi-
tivity to these parameterizations, several previous stud-
ies have performed numerical simulations of real-case
TCs and compared the results with observations (e.g.,
Braun and Tao 2000; Davis and Bosart 2002). Through
this comparison, the model’s ability to accurately rep-
resent a TC can be assessed, and, indirectly the validity
of model design assumptions can be investigated.
In addition to turbulence parameterization, it is rec-
ognized that TC simulations are sensitive to other pa-
rameterizations as well, such as precipitation micro-
physics (e.g., Rogers et al. 2007), and subgrid-scale cu-
mulus convection (e.g., Ooyama 1982; Karymampudi et
al. 1998). While we recognize these sensitivities, our
emphasis here is upon the turbulence parameterization,
and in particular the surface flux parameterization.
In addition to these parameterization issues, TC
simulations are also sensitive to horizontal and vertical
resolution (e.g., Braun and Tao 2000; Davis and Bosart
2002; Persing and Montgomery 2003; Zhang and Wang
2003; Kimball and Dougherty 2006), since altering the
grid spacing influences how well different physical pro-
cesses are resolved, and impacts the behavior of param-
eterization schemes. Braun and Tao (2000) found that
smaller horizontal grid spacing led to more intense
modeled TCs. However, Davis and Bosart (2002) found
that simulations of Hurricane Diana (1984) were more
intense on a 9-km grid than on a 3-km grid because of
a distribution of vertical motion on the 9-km grid that
was skewed toward updrafts, increasing vorticity gen-
eration through stretching. Higher-resolution simula-
tions have also been shown to resolve mixing between
the low-level eye and the eyewall, which provides extra
buoyancy to eyewall updrafts, leading to more intense
simulated TCs (e.g., Persing and Montgomery 2003; Wu
et al. 2006; Montgomery et al. 2006; Cram et al. 2007).
This study aims to quantify the sensitivity of simu-
lated TCs to SL and PBL representation and model
grid spacing through the use of idealized simulations. In
contrast to many previous studies, we will utilize ideal-
ized simulations of long duration. The use of idealized
conditions conducive to intense TC development allows
for model results to be viewed in the absence of case-
specific conditions. A comparison between model results
and observationally based empirical estimates of maxi-
mum potential intensity (MPI) is presented and is used as
a benchmark for model performance in the place of ob-
servations. This comparison is a necessary prerequisite
to a more complete implementation of high wind speed
exchange coefficients in NWP models. Flux and ex-
change coefficient values are compared for two widely
used SL schemes, and the results are discussed in light
of recent observational measurements.
In section 2, the numerical experiments are de-
scribed, including the idealized initial and boundary
condition dataset, the methods used to estimate MPI,
and other model configurations. Section 3 provides a
description of the TC intensity found in each simula-
tion, and a comparison of the results to the empirically
estimated maximum intensity. Section 4 describes the
sensitivity of model surface fluxes to the SL parameter-
ization scheme, and conclusions are presented in sec-
tion 5.
2. Simulation description
a. Model
Version 2.1.21 of the WRF-ARW model (Skamarock
et al. 2005) was used to conduct two separate sets of
model experiments designed to test the sensitivity to
model physics and grid spacing (Table 1), with each set
utilizing either the Yonsei University (YSU) or the
Mellor–Yamada–Janjic (MYJ) suite of PBL and SL pa-
rameterizations. WRF version 2.1.2 must be run with
PBL and SL schemes as a matching pair, precluding the
ability to test SL or PBL schemes individually. Higher-
1 Results obtained from version 2.2 are consistent with those
presented here.
746 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
resolution simulations were performed using one-way
interactive nests between the coarse grid (36-km grid
spacing) and two finer grids (12 and 4 km). Both the 12-
and 4-km grids were moved using an automatic vortex-
tracking algorithm to keep the storm nearly centered in
the nested domains; despite a lack of environmental
flow in the idealized model environment, beta drift gen-
erates a west-northwest movement of the simulated
TCs. The model simulations utilized 31 vertical layers,
with a higher concentration located in the boundary
layer.
The Kain–Fritsch cumulus parameterization scheme
(Kain and Fritsch 1993; Kain 2004) was used to estimate
the effects of subgrid-scale convection on the 12- and
36-km grids, while cumulus convection was not param-
eterized on the 4-km grids. The top of the model atmo-
sphere was set at the 50-hPa pressure level, with a Ray-
leigh damping layer used near the model top in order to
prevent the reflection of wave energy back into the
model domain. The Purdue–Lin scheme was used for
the parameterization of microphysical processes (Lin et
al. 1983; Hong et al. 2004). The Rapid Radiative Trans-
fer Model (RRTM) scheme, based on Mlawer et al.
(1997) and adapted from the fifth-generation Pennsyl-
vania State University–National Center for Atmo-
spheric Research (PSU–NCAR) Mesoscale Model
(MM5), was used to estimate the effects of longwave
radiation. Shortwave radiation was represented using
the scheme described by Dudhia (1989).
The SL schemes compute roughness length, friction
velocities, exchange coefficients, and surface fluxes.
The SL parameterization scheme compatible with the
YSU PBL scheme is based on Monin–Obukhov simi-
larity theory (Monin and Obukhov 1954), with several
modifications. Surface exchange coefficients for heat,
moisture, and momentum are estimated using stability
functions from Paulson (1970), Dyer and Hicks (1970),
and Webb (1970). The YSU SL scheme classifies the
surface layer as being representative of one of four sta-
bility regimes as discussed by Zhang and Anthes
(1982), which are determined by the Bulk Richardson
number (BR). The MYJ SL scheme (Janji�c 1996, 2002;
Z. I. Janji�c 1998, personal communication) is also based
on Monin–Obukhov similarity theory. Using an itera-
tive approach, first-guess momentum and heat flux val-
ues are used to estimate the Obukhov length. The it-
erative procedure typically converges after three or less
iterations (Z. I. Janji�c 1998, personal communication).
Tendencies of basic variables due to turbulent eddies
are computed by the model PBL scheme. Using values
of surface fluxes calculated by the SL scheme, the PBL
scheme estimates flux distributions within the boundary
layer, providing tendencies of temperature, moisture,
and horizontal momentum. The YSU PBL scheme
(Noh et al. 2003; Hong et al. 2006) is a successor to the
MRF PBL scheme (Hong and Pan 1996), and estimates
fluxes due to nonlocal gradients using countergradient
terms. New to the YSU scheme is an explicit treatment
of the entrainment at the PBL top, which was found to
significantly improve model results (Noh et al. 2003;
Hong et al. 2006). The PBL top is defined using a criti-
cal BR number of zero, and is generally lower than in
the MRF scheme. The MYJ PBL parameterization is
based on Mellor–Yamada 2.5-level turbulence closure.
The PBL height in this scheme is defined based on
turbulent kinetic energy (TKE). The vertical limit over
which mixing can occur in this scheme is proportional
to the TKE and a function of large-scale buoyancy and
shear parameters (Janji�c 2002).
b. Environment and initial conditions
Model runs were initialized with an idealized tropical
environment designed to allow for the development of
strong TCs. The idealized initial conditions were used
to initialize the full-physics WRF Model on an actual
geophysical domain, but with the domain set to include
only water. Tropical cyclones in the real atmosphere
rarely attain their MPI, often because of the limiting
effects of wind shear and upwelling (e.g., DeMaria and
Kaplan 1994, hereinafter DK94; Tonkin et al. 2000), in-
teractions with land, and dry environmental air. To pro-
vide atmospheric conditions within which a TC should
reach its MPI, a model domain consisting of all water
was constructed with (i) a horizontally uniform, time-
independent SST of 298C, (ii) no environmental wind
shear, and (iii) a constant environmental relative hu-
TABLE 1. List of simulation names for idealized simulations.
Simulation name PBL/SFC physics Cumulus parameterization Grid spacing (km) Grid dimension Vertical levels
MYJ36 MYJ Kain–Fritsch 36 99 3 104 31
MYJ12 MYJ Kain–Fritsch 12 111 3 111 31
MYJ4 MYJ None 4 246 3 246 31
YSU36 YSU Kain–Fritsch 36 99 3 104 31
YSU12 YSU Kain–Fritsch 12 111 3 111 31
YSU4 YSU None 4 246 3 246 31
FEBRUARY 2009 H I L L A N D L A C K M A N N 747
midity of 80%. The ambient temperature profile (and
lateral boundary condition for the outermost domain)
was specified by the mean tropical sounding of Jordan
(1958), within which a weak initial vortex (i.e., maxi-
mum near-surface wind speeds of ;22 m s21 and mini-
mum central pressure of ;990 hPa) in hydrostatic and
gradient wind balance was inserted. Model simulations
were performed with a wide variety of idealized vorti-
ces, ranging from an unbalanced warm bubble to fully
balanced vortices. The most important difference be-
tween these runs was the amount of time required for
the system to reach maximum intensity; an initial vor-
tex strength of 22 m s21 was used in order to reduce the
amount of time needed to reach the maximum inten-
sity, while not overprescribing the system structure.
These findings, which are consistent with previous ide-
alized modeling studies (e.g., Ooyama 1969; Rosenthal
1971), are not presented here in the interest of brevity.
In this case, an integration length of 10 days allowed for
the simulated TCs to attain a quasi-steady maximum
intensity and then begin weakening. Experiments with
varying run length confirm that 10 days is adequate for
the purposes of this study.
c. MPI comparisons
DK94, utilizing a 31-yr sample of tropical cyclones in
the North Atlantic basin, developed an empirical rela-
tionship between climatological sea surface tempera-
ture (SST) and TC maximum intensity. The results
were shown to agree with the theoretical MPI formu-
lation of Emanuel (1988). The observationally based
empirical formulation for MPI of DK94 will provide the
basis for a comparison to the model runs; a SST of 298C
predicts maximum sustained 10-m winds (V10max) of
;75 m s21. DK94 do not provide an estimate of mini-
mum central pressure (Pmin), but a V10max of 75 m s21
corresponds to a Pmin value of 910 hPa using the pres-
sure–wind relationship of Brown et al. (2006), or 891
using the relation of Atkinson and Holliday (1977). The
difference in the relationship between Pmin and V10max
in these two studies is likely due to the observational
datasets used to determine the relationship; the Atkin-
son and Holliday (1977) study utilized a dataset con-
sisting of Pacific TCs, while Brown et al. (2006) utilized
data from Atlantic TCs. Since the idealized initial vor-
tex is not necessarily intended to represent either ocean
basin, simulated MSLP values will be compared to both
estimates.
3. Intensity
To determine a 10-m wind speed value from the
model output, an assumption regarding the wind speed
profile in the boundary layer is required, since the low-
est model layer is above 10 m. For consistency with the
observationally determined estimates of maximum
10-m wind speed used in DK94, 10-m wind speed was
obtained by multiplying the model wind speed at the
700-hPa level by 0.90 [based upon the recommendation
of Franklin et al. (2000) and used in DK94]. Sampling
issues exist when comparing model results to observa-
tions, since the maximum intensity of an observed TC
may not always be sampled sufficiently. This issue must
be taken into account when comparing the results of the
model simulations with the observationally based MPI
estimates of DK94.
Figure 1 shows a time series of the model-simulated
V10max for the duration of the 240-h simulations. In each
simulation, the storm undergoes a period of rapid in-
tensification during the first 24 h of model integration,
reaching hurricane strength (;33 m s21) within 12 h.
Simulations using 4- or 12-km grid spacing intensify at
nearly the same rate through 24 h, but after this time
maximum winds level off in the 12-km simulations,
while continuing to increase in the 4-km simulations.
After hour 72, V10max is quasi-steady (610 m s21) in all
simulations except YSU4, where an increase in the TC
size after simulation hour 120 led to a weaker pressure
gradient (not shown) and weaker V10max (Fig. 1b).
Simulations with higher resolution produce stronger
winds, and the MYJ4 and YSU4 simulations both ex-
ceed the estimated MPI of 75 m s21; however, the dif-
ference of ;5 m s21 in the YSU4 run is quite small,
given the assumptions used in our 10-m wind compu-
tation and uncertainty in the observations that were
used to derive this empirical MPI. Simulations with 12-
km grid spacing produce peak V10max values that are
near (,5 m s21 difference) the MPI, while the 36-km
grid spacing simulations are 5–10 m s21 below the
MPI.2
Figure 2 shows a time series of the model-simulated
Pmin. The evolution of Pmin is similar to that of V10max,
with rapid deepening in the first 24 h of each simula-
tion, varying amounts of intensification between 24 and
144 h depending upon the specific simulation, and then
quasi-steady Pmin after hour 144. The 4-km simulations
produce TCs with the lowest Pmin values, yielding pres-
sures slightly lower than those provided by either of
the pressure–wind relationships described above. The
TC in simulation YSU12 attains a minimum central
2 We acknowledge that the comparison between maximum
wind speed values between model domains with different grid
spacings is not direct, as smaller grid boxes more easily attain a
given maximum speed than larger grid boxes. However, the result
of higher intensity in the higher-resolution runs was also evident
with all data interpolated to a 36-km grid (not shown).
748 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
pressure of 900 hPa, a value that falls between the Pmin
estimates discussed above. Simulations MYJ12,
YSU36, and MYJ36 all reach a similar Pmin of ;910–
915, within ;5 hPa of the estimate based on Brown et
al. (2006). The sensitivity of Pmin to parameterization
choice varies with grid spacing, with simulations utiliz-
ing the MYJ parameterizations and 4 (12) km grid spac-
ing being more (less) intense than those with YSU.
Simulations with 36-km grid spacing were of compa-
rable intensity with the two schemes. We speculate that
the use of a convective parameterization (CP) scheme
in the 12- and 36-km simulations could contribute to
this discrepancy; CP scheme activity in the eyewall re-
duces the TC secondary circulation, and the interplay
between shallow mixing in the CP scheme and param-
eterized moist entrainment in the YSU scheme may
explain the differences between runs with explicit and
parameterized convection. Additional simulations
would be required to determine whether TCs in MYJ
simulations would be consistently stronger than for the
YSU scheme, but this was the case for all of the explicit
convection runs that we performed.
FIG. 1. Time series of model maximum 10-m wind speed (m s21; model run indicated in
legend) for the (a) MYJ and (b) YSU simulations.
FEBRUARY 2009 H I L L A N D L A C K M A N N 749
The fact that in the simulations using 4-km grid spac-
ing Pmin values showed little sensitivity to parameter-
ization choice, while V10max values did, is likely due to
differences in the simulated TC size. After simulation
hour 120, the simulated TC in YSU4 grew to be much
larger than in MYJ4. Therefore, despite a continued
deepening of the vortex, the maximum V10max values in
YSU4 are found before simulation hour 120, while the
lowest Pmin occurs close to simulation hour 200. The
sensitivity of model-simulated TC size to the surface
layer and planetary boundary layer parameterization
schemes is the topic of ongoing research.
4. Sensitivity of fluxes and exchange coefficients toSL parameterization
Since theory and previous modeling studies have in-
dicated a relationship between hurricane intensity and
the model turbulent exchange coefficients (Ooyama
1969; Rosenthal 1971; Emanuel 1995; Braun and Tao
2000), it is anticipated that different exchange coeffi-
FIG. 2. Time series of model minimum central pressure (hPa; model run indicated in
legend) for the (a) MYJ and (b) YSU simulations.
750 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
cients (and fluxes) computed by the WRF SL param-
eterization schemes tested here will contribute sub-
stantially to the differences in simulated TC intensity.
Because the SL characteristics may vary in each simu-
lation because of factors other than the SL parameter-
ization (such as the different PBL schemes being used),
it can be difficult to evaluate the SL schemes unless
identical winds, temperatures, and vapor mixing ratios
are used in the calculations. To alleviate this difficulty,
the values of different SL parameters from the 4-km
grid spacing simulations will be presented as a function
of the 10-m wind speed. The model output 10-m wind
speed is much less than the 10-m wind speed we esti-
mate utilizing from multiplying the 700-hPa wind speed
by 0.9, but it is used for analyzing the surface layer
parameters because it is the wind speed used by the
schemes for the calculations. Output from simulation
hour 102 will be shown, since the TCs exhibited similar
near-surface wind speeds at this time (Fig. 3). Exami-
nation of other times demonstrates that the results are
not sensitive to this choice. To examine the average
conditions near the TC center, 280-km area-averaged
(hereafter AA) fields will be discussed. The 280-km
distance was chosen because it allows for the core of
strong winds to be covered, although the results are not
highly sensitive to this choice. The AA 10-m wind
speed (V10) is nearly identical between the two 4-km
runs at this simulation hour, allowing for a consistent
comparison between area-averaged SL parameters
(Table 2).
Figure 4 displays latent heat flux (LHFLX) as a func-
tion of 10-m wind speed. Values of LHFLX are larger
in MYJ4 than in YSU4 at wind speeds stronger than
;17 m s21, with the largest differences, up to 1000 W
m22, found at wind speeds above 55 m s21. The AA
10-m wind speeds vary by ;1 m s21 between the runs,
yet the AA LHFLX is 178 W m22 (;22%) larger in the
MYJ4 simulation (Table 2). The large disparity in the
LHFLX values could be due to different vertical mois-
ture gradients near the ocean surface in the simulations,
or due to other differences within the SL schemes. To
investigate these possibilities, the difference in specific
humidity between the surface and 10 m was calculated
(hereinafter referred to as Dq0–10). All else being equal,
the moisture flux should be larger in a simulation in
which the vertical water vapor gradient near the ocean
surface is larger. However, Fig. 5 reveals that the near-
surface vertical moisture gradient is larger in the YSU4
simulation relative to MYJ4 at all wind speeds shown.
At high wind speeds, where LHFLX values are ;50%
larger in MYJ4, Dq0–10 remains larger in the YSU4
simulation. These results suggest that the significant
differences in the LHFLX between the schemes is re-
lated to the moisture exchange coefficient, CQ (see the
Appendix for the computational method), which is
shown in Fig. 6 as a function of wind speed. In MYJ4,
CQ linearly increases with wind speed, while in YSU4
CQ is nearly constant with wind speed. At wind speeds
of 50 m s21 and above, the CQ value in the MYJ4 simu-
lation is more than twice as large as in YSU4, and over-
all the AA CQ value is ;50% larger in MYJ4 (Table 2).
To summarize, AA LHFLX values are 22% larger in
the MYJ4 simulation despite having a smaller gradient
of moisture near the surface, because of a larger ex-
change coefficient for moisture.
While there are large differences in LHFLX values
produced in the simulations, the values of sensible heat
flux (HFLX) are more similar (Fig. 7). Values of HFLX
differ by up to ;50 W m22. The AA HFLX values are
;30% larger in the MYJ4 simulation (Table 2), but this
difference can be mainly attributed to the distribution
of potential temperature (u) in the SL. The near-
surface vertical u gradient is larger in the MYJ4 simu-
lation at almost all wind speeds (Fig. 8), leading to an
AA vertical u gradient that is ;27% larger (Table 2).
The values of the exchange coefficient for sensible heat,
Cu, used in the schemes are within 5% of one another at
all wind speeds shown (Fig. 9) and AA values vary by
,3% (Table 2), supporting the fact that the calculation
of HFLX is nearly identical in the MYJ and YSU SL
schemes. Examination of Table 2 reveals that the ex-
change coefficients for moisture and heat are identical
in the MYJ4 simulation, but are not in YSU4.
Figure 10 is a plot of the momentum exchange coef-
ficient, CD, as a function of 10-m wind speed. Through-
out the range of winds speeds shown, CD is nearly iden-
tical in the two model simulations, indicating that dif-
ferences in this parameter likely did not play a role in
the sensitivity to the surface layer parameterization.
Emanuel (1995), utilizing an idealized hurricane
model, investigated the sensitivity of simulated TC in-
tensity to the ratio Ck (the exchange coefficient for
enthalpy) to CD. The results suggested that the value in
real hurricanes is likely between 0.75 and 1.5. As pre-
viously shown, the exchange coefficients for heat and
water vapor are equal in the MYJ SL scheme, but not
in the YSU scheme. Therefore, the ratios Cu/CD and
CQ/CD will each be examined separately. At almost all
wind speeds, Cu/CD is larger in the MYJ4 simulation
(Fig. 11), although the largest difference is ;3%, and
AA values are within 1% of one another (Table 2).
Values at all wind speeds fall within the range sug-
gested by Emanuel (1995). The ,1% difference in the
AA Cu/CD value is not likely to fully explain the ob-
served difference in intensity. Figure 12 displays the
value of the ratio CQ/CD. Owing to the fact that CQ
FEBRUARY 2009 H I L L A N D L A C K M A N N 751
increases more slowly with wind speed than CD in the
YSU4 simulation, the ratio CQ/CD decreases with in-
creasing wind speed. The largest difference in CQ/CD is
at wind speeds greater than 50 m s21, where CQ/CD is
approximately twice as large in the MYJ4 simulation.
The AA values of the ratio are ;55% larger the MYJ4
simulation. At wind speeds above ;35 m s21, the ratio
in the YSU4 simulation is less than the minimum value
suggested by Emanuel (1995), although it is difficult to
assess the realism of this behavior due to a lack of flux
observations at high wind speeds over water. We specu-
late that the large difference in this ratio is most likely
responsible for the differences in simulated TC inten-
sity seen in the MYJ4 and YSU4 simulations.
FIG. 3. Model 10-m wind speed (shaded; m s21) at simulation hour 102 for the (a) MYJ and
(b) YSU simulations. The black contour indicates the 280-km distance from the TC centers.
752 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
5. PBL tendencies
The impact of PBL parameterization on the vertical
structure of the simulated TCs was assessed by exam-
ining vertical cross sections of temporally and azimuth-
ally averaged potential temperature and mixing ratio,
along with tendencies of temperature and moisture due
to PBL parameterization. Hourly model output from
the 4-km grid spacing simulations during the period
from 72 to 84 h was used. In cases where negative and
positive tendencies were both present, the tendencies
were averaged separately, to avoid cancellation.
Figure 13 displays the average potential temperature
from the 4-km simulations for this 12-h interval. A re-
alistic warm-core structure is evident in both simula-
tions (Figs. 13a,b), although the TC core is generally
warmer in the MYJ4 simulation than in YSU4 (Fig.
13c). The largest difference (;8 K) is found between 4-
and 6-km altitude within ;35 km of the TC center. The
difference in potential temperature in this area can be
partially attributed to PBL scheme tendencies of heat
(Fig. 14). The YSU PBL scheme produced strong (;10
K h21) cooling in this area (Fig. 14b), while the MYJ
PBL scheme produced no tendency (Fig. 14a).
Outside of the eye, large differences in the magni-
tude and location of PBL scheme potential temperature
tendency exist as well. Azimuthally and temporally av-
eraged positive (warming) tendencies are up to ;8 K in
both schemes, while the maximum cooling is approxi-
mately one order of magnitude larger in the YSU
scheme. The YSU scheme produces appreciable ten-
dencies up to ;8-km altitude, while the MYJ scheme
FIG. 4. Model latent heat flux (W m22) as a function of 10-m wind speed (simulation
indicated in legend) at simulation hour 102.
TABLE 2. Model 10-m wind speed, surface latent heat flux (LHFLX), the difference in specific humidity between the surface and the
10-m level (Dq0–10), sensible heat flux (HFLX), the difference in potential temperature between the surface and the 10-m level (Du0–10),
the exchange coefficient for moisture (CQ), heat (Cu) and momentum (CD), and the ratios Cu/CD and CQ/CD. For each simulation, the
first number in the column is the average value within 280 km of the storm and the second and third numbers are the minimum and
maximum within that area. Values are from simulation hour 102.
Case
10-m wind
(m s21)
LHFLX
(W m22)
Dq0–10
(g kg21)
HFLX
(W m22) Du0–10 (K) CQ (3 1023) Cu (3 1023) CD (3 1023) Cu/CD CQ/CD
MYJ4 27.58 971 2.41 133 1.28 2.30 2.30 2.60 0.89 0.89
1.31 26 1.34 4 0.45 1.30 1.30 0.90 0.80 0.80
60.22 3455 3.06 840 4.40 4.13 4.13 4.92 1.46 1.46
YSU4 28.51 793 2.40 103 0.88 1.09 2.35 2.65 0.89 0.58
0.78 13 1.56 1 0.21 0.95 1.12 1.11 0.85 0.40
58.18 2014 3.07 642 3.86 1.90 4.08 4.80 1.03 1.01
FEBRUARY 2009 H I L L A N D L A C K M A N N 753
generally produces a shallower layer of heating and
cooling, up to ;5-km altitude.
Figure 15 displays the average mixing ratio from the
4-km simulations, with an outward-sloping eyewall seen
in both simulations (Figs. 15a,b). The largest difference
in mixing ratio is found in the TC center, where the
MYJ4 simulation is dryer than in YSU4 by up to ;4 g
kg21 (Fig. 15c). The difference in mixing ratio in the
aforementioned area can be partially attributed to PBL
scheme tendencies of moisture (Fig. 16). The YSU PBL
scheme produced strong (.4.5 g kg21) moistening in
this area (Fig. 16b), while the MYJ PBL scheme pro-
FIG. 5. The difference in mixing ratio (g kg21) between the surface and the 10-m level, as a
function of 10-m wind speed (simulation indicated in legend).
FIG. 6. The exchange coefficient for moisture, CQ (3 1023), as a function of 10-m wind
speed (simulation indicated in legend).
754 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
duced no tendency (Fig. 16a). Outside of the eye, the
PBL schemes in general produce a similar pattern of
mixing. The YSU scheme produces negative (drying)
tendencies that are up to 10 times larger than in MYJ.
6. Discussion and conclusions
The WRF model has been used to produce idealized
TC simulations within an environment that allows for
intensification to the environmental MPI of the model
atmosphere. The empirical relationship between SST
and maximum intensity of DK94 provides a comparison
that is useful in determining the overall consistency of
the model with observations, although it is important to
emphasize that numerous complexities exist when com-
paring observations to model output and the intensity
comparison is more qualitative than quantitative in na-
FIG. 7. Model sensible heat flux (W m22) as a function of 10-m wind speed (simulation
indicated in legend).
FIG. 8. The difference in potential temperature between the surface and the 10-m level (K)
as a function of 10-m wind speed (simulation indicated in legend).
FEBRUARY 2009 H I L L A N D L A C K M A N N 755
ture. More specifically, the sensitivity to model resolu-
tion and SL and PBL physics was investigated by per-
forming two separate experiments, where the horizon-
tal grid spacing was varied on three domains. Much of
the model sensitivity is attributed to the SL physics,
although large differences in PBL scheme–induced
mixing have been shown to exist, and could impact the
simulated TC intensity as well. Additional sensitivity of
the results to microphysics parameterization, the use of
convective parameterization on the outer grids, or
other aspects of the model have not been systematically
addressed here.
FIG. 9. The exchange coefficient for sensible heat, Cu (3 1023), as a function of 10-m wind
speed (simulation indicated in legend).
FIG. 10. The momentum exchange coefficient, CD (3 1023), as a function of 10-m wind
speed (simulation indicated in legend).
756 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
a. Maximum TC intensity
The maximum intensity reached in the simulations
exhibited strong sensitivity to horizontal grid spacing,
and to a lesser extent to the choice of SL and PBL
parameterization. Simulations using 4-km grid spacing
produced TCs that were of comparable intensity to em-
pirical MPI estimates for the idealized environment,
while simulations using coarser (12 or 36 km) grid spac-
ing were weaker. The greater intensity seen in the
higher-resolution domains is likely due to either (i) the
omission of convective parameterization on the 4-km
grid, and/or (ii) the ability of the higher-resolution do-
main being able to at least partially resolve mixing by
FIG. 11. The ratio of the exchange coefficient for heat to the exchange coefficient
momentum (Cu /CD) as a function of 10-m wind speed (simulation indicated in legend).
FIG. 12. The ratio of the exchange coefficient for moisture to the exchange coefficient for
momentum (CQ /CD) as a function of 10-m wind speed (simulation indicated in legend).
FEBRUARY 2009 H I L L A N D L A C K M A N N 757
FIG. 13. Temporally and azimuthally averaged potential temperature (K)
for the (a) MYJ4, (b) YSU4, and (c) MYJ4 – YSU4 simulations.
758 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
eyewall vortices between the low-level eye and the eye-
wall; these findings are thus consistent to those of Pers-
ing and Montgomery (2003), Braun et al. (2006), and
Cram et al. (2007). Simulations utilizing sub 4 km have
not been tested here, but we speculate that simulations
with even higher resolution would be more intense
(Montgomery et al. 2006; Gentry 2007).
b. Fluxes and exchange coefficients in the YSU andMYJ schemes
Large differences are shown to exist between LH-
FLX computations between the two available surface
layer parameterization schemes in WRF. The MYJ
scheme produces values of LHFLX that are up to 1000
FIG. 14. Temporally and azimuthally averaged PBL potential temperature tendency (K
h21). Positive (negative) values are shaded (contoured) for the (a) MYJ4 and (b) YSU4
simulations. Note that positive and negative tendencies are contoured at different intervals,
and the negative tendencies are contoured at different intervals between the schemes.
FEBRUARY 2009 H I L L A N D L A C K M A N N 759
FIG. 15. Temporally and azimuthally averaged mixing ratio (g kg21) for
the (a) MYJ4, (b) YSU4, and (c) YSU4 – MYJ4 simulations.
760 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
W m22 (;50%) larger than those in the YSU scheme at
the same wind speeds. This was traced to a larger ex-
change coefficient for moisture (CQ) in the MYJ
scheme. The CQ in the YSU scheme is nearly indepen-
dent of wind speed (varying between 1.4 and 1.8), while
in the MYJ scheme CQ linearly increases with wind
speed, reaching a value of ;3.8 3 1023 at a wind speed
of ;55 m s21. The difference in the LHFLX values
calculated by the schemes increases with increasing
wind speed, suggesting that the sensitivity of TC inten-
sity to the parameterization scheme may be largest for
intense systems. The large values of LHFLX at high
wind speeds due to the large CQ value may have been
the factor that allowed the MYJ4 simulation to exceed
FIG. 16. Temporally and azimuthally averaged PBL water vapor tendency (g kg21 h21).
Positive (negative) values are shaded (contoured) for the (a) MYJ4 and (b) YSU4 simulations.
Note that negative tendencies in the MYJ4 simulation are multiplied by 10, and that the
contour interval of the negative and positive tendencies is different.
FEBRUARY 2009 H I L L A N D L A C K M A N N 761
the intensity of YSU4. Values of HFLX and the ex-
change coefficients for momentum and heat are nearly
identical in the MYJ and YSU schemes.
c. Comparison with observations
Assessing which scheme is more realistic is compli-
cated by the lack of observations at high wind speeds
over oceans. Numerous studies have attempted to esti-
mate the turbulent exchange coefficients over water in
high wind speed conditions (e.g., Smith 1980; Large and
Pond 1981; Smith et al. 1992; Yelland et al.1998; Powell
et al.2003) utilizing a wide range of measurement plat-
forms and analysis techniques. Measurements during
the 2002–04 Coupled Boundary Layers Air–Sea Trans-
fer (CBLAST) field program were made at wind speeds
up to ;28 m s21, allowing for the exchange coefficients
to be estimated based on measurements at higher wind
speeds than was previously possible. Model-simulated
wind speeds greatly exceeded these values, but never-
theless, CBLAST observations provide the best metric
for assessing the surface layer parameterization
schemes over the widest range of wind speeds possible.
CBLAST observations indicate that CD is quasi-steady
at wind speeds within the range of ;18–28 m s21 (Black
et al. 2007, their Fig. 5), with a value of 1.5–2.0. At wind
speeds in this range, CD is nearly identical in the MYJ
and YSU SL schemes, with a value of ;2.1–2.6 3 1023,
exceeding the upper bound of the observations. At
wind speeds . 30 m s21, CD increases with wind speed
in both model SL schemes, reaching a value of ;4.6 3
1023 at a wind speed of ;55 m s21. Based on the avail-
able observations, it is evident that the momentum ex-
change coefficient may be too large in both the YSU
and MYJ schemes.
CBLAST observations indicate that the exchange co-
efficient for moisture is quasi-steady with increasing
wind speed for wind speeds ,28 m s21. The CQ in-
creases slowly with wind speed in the YSU scheme,
while in MYJ it increases more rapidly with increasing
wind speed. At wind speeds ,28 m s21, CQ in the YSU
scheme more closely matches the observations. At a
wind speed of ;28 m s21, the CQ value from the MYJ
scheme exceeding the upper bound of the observations,
suggesting that the scheme overestimates CQ, and con-
sequently LHFLX. The wind speed dependence of CQ
in higher wind speed conditions (.;30 m s21) is diffi-
cult to assess given the limited range of observational
data, although it is clear that the MYJ scheme produces
much larger values than YSU.
Previous modeling studies and theoretical work sug-
gest that the ratio of the exchange coefficient for en-
thalpy to the exchange coefficient for momentum
strongly influences simulated TC intensity. Here it is
suggested that when Cu 6¼ CQ, the ratios Cu/CD and
CQ/CD can both impact simulated TC intensity, and,
given the fact that latent heat fluxes are much larger
than sensible, CQ/CD may ultimately be more impor-
tant. Theory suggests that increasing (decreasing) these
ratios should lead to a more (less) intense simulated
TC, and that the ratio should be between 0.75 and 1.5
(e.g., Emanuel 1995). Observations, although limited to
wind speeds ,30 m s21, indicate that the ratio may be
toward the lower end of that spectrum, with a value of
;0.75 (Black et al. 2007, their Fig. 7). Recent modeling
studies suggest that full-physics numerical models can
produce TCs of realistic intensity while utilizing values
of this ratio of ,0.75 (Cram et al. 2007). The ratio
Cu/CD is similar in the MYJ4 and YSU4 simulations,
with values between 0.8 and 0.95, in good agreement
with Emanuel (1995) and slightly larger than that indi-
cated by CBLAST observations (but within the range
of uncertainty in the measurements). The small differ-
ences in this ratio likely do not contribute to differences
in model TC intensity.
The ratio CQ/CD varies significantly between the
schemes; in the MYJ4 simulation the value is between
0.8 and 0.95, while in YSU4 the ratio decreases from
;0.75 to 0.40 as wind speed increases from 20 to 55
m s21. This ratio is less than that suggested by Emanuel
(1995), although this does not necessarily indicate a
problem, as the model is still capable of producing re-
alistic TC intensity. The value in YSU4 at a wind speed
of 30 m s21 falls within the 95% confidence interval of
the CBLAST observations, but the decrease at higher
wind speeds cannot be assessed using currently avail-
able observations. The smaller ratio at high wind
speeds should lead to less intense TCs in YSU than in
simulations with the MYJ SL scheme. Owing to the fact
that the ratio becomes more dissimilar at higher wind
speeds, it is anticipated that simulations of weaker TCs
would exhibit less sensitivity to SL parameterization.
The results presented here are consistent in this regard,
as modeled TC intensity using 36-km grid spacing was
similar (,1 m s21 difference in peak V10max), whereas
TC intensity using 4-km grid spacing varied consider-
ably (;10 m s21 difference in peak V10max).
d. Implications for TC modeling
Based upon the observational data it is evident that a
linear extrapolation of measured exchange coefficient
values at low wind speeds, as is done in the MYJ and
YSU schemes, may not yield physically realistic ex-
change coefficient values in the high wind speed con-
ditions of an intense TC. Despite this apparent incon-
762 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
sistency between the model values and observations,
and even for an extremely intense TC, WRF-ARW is
capable of producing simulated TC intensity that is
comparable to empirical estimates of maximum inten-
sity. It is unclear what effect modifying the model ex-
change coefficients in the model would produce, al-
though theory suggests that if both CD and CQ (or Cu)
were changed in the same sense then the simulated TC
intensity should not change. Changes that lead to the
ratio increasing (decreasing), however, should lead to
more (less) intense simulated TCs. Although not un-
dertaken in this project, a logical extension of this re-
search would be to test the surface parameterization
schemes on real and idealized cases while utilizing ex-
change coefficients that are more consistent with ob-
servations.
If future observational field programs are able to ob-
tain flux measurements beneath the TC eyewall at wind
speeds above 30 m s21, then corrections to model ex-
change coefficients will emerge. Comparisons of results
from simulations with the revised SL schemes should be
compared with observationally derived MPI values to
best calibrate the models. With accurate model ex-
change coefficients at high wind speeds over water, im-
provements in TC intensity forecasting may be within
reach. Coupled ocean–wave–atmosphere models, of the
type discussed by Chen et al. (2007) perhaps offer the
best hope for improvement of these important param-
eterization schemes, as the turbulent exchanges of heat,
moisture, and momentum over water in the real atmo-
sphere cannot be realistically parameterized as func-
tions of wind speed alone.
Acknowledgments. This research was funded by NSF
Grant ATM-0334427, awarded to North Carolina State
University. The WRF model was made available
through NCAR. We thank Dr. Mike Brennan (TPC)
and three anonymous reviewers for useful comments
on a previous version of this manuscript.
APPENDIX
Calculating Surface Layer Exchange Coefficients
The exchange coefficients CQ, Cu, and CD are not
output directly from the model, but are computed di-
agnostically using model-calculated fields. Both CQ and
Cu are calculated using the output variables FLQC and
FLHC, respectively. FLQC and FLHC are the ex-
change coefficients for moisture and heat, respectively,
but have the unit of meters per second. The surface
layer schemes calculate moisture and heat fluxes using
the following equations:
QFX 5 FLQC(QSFC�QX) and (A1)
HFX 5 FLHC(THGB� THX), (A2)
where QFX and HFX are moisture and heat flux,
QSFC and QX are mixing ratios at the surface and at
the 10-m level, and THGB and THX are the potential
temperature values at the surface and at the 10-m level.
Rearranging (A1) and (A2), FLQC and FLHC become
the following:
FLQC 5QFX
QSFC�QXand (A3)
FLHC 5HFX
THGB� THX. (A4)
In a bulk formula framework, the fluxes are calculated as
QFX 5 raVaCQ(QSFC�QX), (A5)
HFX 5 racpVaCu(THGB� THX), (A6)
where ra is air density at the 10-m level, cp is the heat
capacity of dry air at constant pressure, Va is the wind
speed at the 10-m level, and CQ and Cu are the ex-
change coefficients for moisture and heat, respectively.
Rearranging (A5) and (A6), the exchange coefficients
are
CQ 5QFX
raVa(QSFC�QX)and (A7)
Cu 5HFX
racpVa(THGB� THX). (A8)
After plugging in (A3) into (A7) and (A4) into (A8),
we get expressions for the exchange coefficients:
CQ 5FLQC
raVaand (A9)
Cu 5FLHC
racpVa. (A10)
As previously stated, FLHC and FLQC are output
from the model. The other variables in the equations
were defined as follows:
d Air density ra at the 10-m level is not standard out-
put from the WRF model, so this quantity was calcu-
lated using a linear interpolation for temperature
(between the 2-m value and the value at the lowest
model level) and for pressure (between the surface
value and the value at the lowest model level).d For this calculation of Va, the model’s 10-m wind
speed (which is standard output) was used.
To calculate the drag coefficient CD, the following
equation was used:
FEBRUARY 2009 H I L L A N D L A C K M A N N 763
CD 5 u2
*/V2a, (A11)
where u*
is the friction velocity output by WRF and Va
is defined as above.
REFERENCES
Aberson, S. D., 2003: Targeted observations to improve opera-
tional tropical cyclone track forecast guidance. Mon. Wea.
Rev., 131, 1613–1628.
Andreas, E. L, and K. A. Emanuel, 2001: Effects of sea spray on
tropical cyclone intensity. J. Atmos. Sci., 58, 3741–3751.
Atkinson, G. D., and C. R. Holliday, 1977: Tropical cyclone
minimum sea level pressure/maximum sustained relation-
ship for the Western North Pacific. Mon. Wea. Rev., 105,
421–427.
Black, P. G., 2004: An overview of CBLAST flights into Hurri-
canes Fabian and Isabel (2003). Preprints, 26th Conf. on Hur-
ricanes and Tropical Meteorology, Miami Beach, FL, Amer.
Meteor. Soc., 1A.1. [Available online at http://ams.confex.
com/ams/pdfpapers/76032.pdf.]
——, and Coauthors, 2007: Air–sea exchange in hurricane winds:
Synthesis of observations from the Coupled Boundary Layer
Air–Sea Transfer Experiment. Bull. Amer. Meteor. Soc., 88,
357–374.
Braun, S. A., and W.-K. Tao, 2000: Sensitivity of high-resolution
simulations of Hurricane Bob (1991) to planetary boundary
parameterizations. Mon. Wea. Rev., 128, 3941–3961.
——, M. T. Montgomery, and Z. Pu, 2006: High-resolution simu-
lation of Hurricane Bonnie (1998). Part I: The organization
of eyewall vertical motion. J. Atmos. Sci., 63, 16–42.
Brown, D. P., J. L. Franklin, and C. Landsea, 2006: A fresh look at
tropical cyclone pressure–wind relationships using recent re-
connaissance-based ‘‘best track’’ data (1998–2005). Preprints,
27th Conf. on Hurricanes and Tropical Meteorology,
Monterey, CA, 3B.5. [Available online at http://ams.confex.
com/ams/pdfpapers/107190.pdf.]
Byers, H. R., 1944: General Meteorology. 1st ed. McGraw-Hill,
645 pp.
Cram, T. A., J. Persing, M. T. Montgomery, and S. A. Braun,
2007: A lagrangian trajectory view on transport and mixing
processes between the eye, eyewall, and environment using a
high-resolution simulation of Hurricane Bonnie (1998). J. At-
mos. Sci., 64, 1835–1856.
Chen, S. S., J. F. Price, W. Zhao, M. Donelan, and E. J. Walsh,
2007: The CBLAST-Hurricane Program and the next-gen-
eration fully coupled atmosphere–wave–ocean models for
hurricane research and prediction. Bull. Amer. Meteor. Soc.,
88, 311–317.
Davis, C., and L. F. Bosart, 2002: Numerical simulations of the
genesis of Hurricane Diana (1984). Part II: Sensitivity of
track and intensity prediction. Mon. Wea. Rev., 130, 1100–
1124.
DeMaria, M., and J. Kaplan, 1994: Sea surface temperature and
the maximum intensity of Atlantic tropical cyclones. J. Cli-
mate, 7, 1324–1334.
——, M. Mainelli, L. K. Shay, J. A. Knaff, and J. Kaplan, 2005:
Further improvement to the Statistical Hurricane Intensity
Prediction Scheme (SHIPS). Wea. Forecasting, 20, 531–543.
Dudhia, J., 1989: Numerical study of convection observed during
the winter monsoon experiment using a mesoscale two-di-
mensional model. J. Atmos. Sci., 46, 3077–3107.
Dyer, A. J., and B. B. Hicks, 1970: Flux-gradient relationships in
the constant flux layer. Quart. J. Roy. Meteor. Soc., 96, 715–
721.
Emanuel, K. A., 1986: An air–sea interaction theory for tropical
cyclones. Part I: Steady-state maintenance. J. Atmos. Sci., 43,
585–604.
——, 1988: The maximum intensity of hurricanes. J. Atmos. Sci.,
45, 1143–1155.
——, 1995: Sensitivity of tropical cyclones to surface exchange
coefficients and a revised steady-state model incorporating
eye dynamics. J. Atmos. Sci., 52, 3969–3976.
Franklin, J. L., M. L. Black, and K. Valde, cited 2000: Eyewall
wind profiles in hurricanes determined by GPS dropwind-
sondes. [Available online at http://www.nhc.noaa.gov/
aboutwindprofile.shtml.]
Gentry, M. S., 2007: Sensitivity of WRF simulations of Hurricane
Ivan to horizontal resolution. M.S. thesis, Dept. of Marine,
Earth, and Atmospheric Sciences, North Carolina State Uni-
versity, 178 pp. [Available online at http://www.lib.ncsu.edu/
theses/available/etd-07052007-125816.]
Hong, S.-Y., and H.-L. Pan, 1996: Nonlocal boundary layer diffu-
sion in a medium-range forecast model. Mon. Wea. Rev., 124,
2322–2339.
——, J. Dudhia, and S.-H. Chen, 2004: A revised approach to ice
microphysical processes for the bulk parameterization of
clouds and precipitation. Mon. Wea. Rev., 132, 103–120.
——, Y. Noh, and J. Dudhia, 2006: A new vertical diffusion pack-
age with an explicit treatment of entrainment processes.
Mon. Wea. Rev., 134, 2318–2341.
Janji�c, Z. I., 1996: The surface layer in the NCEP Eta Model.
Preprints, 11th Conf. on Numerical Weather Prediction, Nor-
folk, VA, Amer. Meteor. Soc., 354–355.
——, 2002: Nonsingular implementation of the Mellor–Yamada
level 2.5 scheme in the NCEP Meso model. NCEP Office
Note 437, 61 pp.
Jordan, C. L., 1958: Mean soundings for the West Indies area. J.
Meteor., 15, 91–97.
Kain, J. S., 2004: The Kain–Fritsch convective parameterization:
An update. J. Appl. Meteor., 43, 170–181.
——, and J. M. Fritsch, 1993: Convective parameterization for
mesoscale models: The Kain–Fritsch scheme. The Represen-
tation of Cumulus Convection in Numerical Models, Meteor.
Monogr., No. 46, Amer. Meteor. Soc., 165–170.
Karymampudi, V. M., G. S. Lai, and J. Manobianco, 1998: Impact
of initial conditions, rainfall assimilation, and cumulus pa-
rameterization on simulations of Hurricane Florence (1998).
Mon. Wea. Rev., 126, 3077–3101.
Kimball, S. K., and F. C. Dougherty, 2006: The sensitivity of ide-
alized hurricane structure and development in the distribu-
tion of vertical levels in MM5. Mon. Wea. Rev., 134, 1987–
2008.
Knaff, J. A., M. DeMaria, C. R. Sampson, and J. M. Gross, 2003:
Statistical, five-day tropical cyclone intensity forecasts de-
rived from climatology and persistence. Wea. Forecasting, 18,
80–92.
Kurihara, Y., M. A. Bender, R. E. Tuleya, and R. J. Ross, 1995:
Improvements in the GFDL hurricane prediction system.
Mon. Wea. Rev., 123, 2791–2801.
——, ——, ——, and ——, 1998: The GFDL hurricane prediction
system and its performance in the 1995 hurricane season.
Mon. Wea. Rev., 126, 1306–1322.
Large, W. G., and S. Pond, 1981: Open ocean flux measurements
in moderate to strong winds. J. Phys. Oceanogr., 11, 324–336.
764 M O N T H L Y W E A T H E R R E V I E W VOLUME 137
Lin, Y.-L., R. D. Farley, and H. D. Orville, 1983: Bulk parameter-
ization of the snow field in a cloud model. J. Climate Appl.
Meteor., 22, 1065–1092.
Mlawer, E. J., S. J. Taubman, P. D. Brown, M. J. Iacono, and S. A.
Clough, 1997: Radiative transfer for inhomogeneous atmo-
sphere: RRTM, a validated correlated-k model for the long-
wave. J. Geophys. Res., 102 (D14), 16 663–16 682.
Monin, A. S., and A. M. Obukhov, 1954: Basic laws of turbulent
mixing in the surface layer of the atmosphere (in Russian).
Contrib. Geophys. Inst. Acad. Sci. USSR, 151, 163–187.
Montgomery, M. T., M. M. Bell, S. D. Abserson, and M. L. Black,
2006: Hurricane Isabel (2003): New insights into the physics
of intense storms. Part I: Mean vortex structure and maxi-
mum intensity estimates. Bull. Amer. Meteor. Soc., 87, 1335–
1347.
Noh, Y., W. G. Cheon, S. Y. Hong, and S. Raasch, 2003: Improve-
ment of the K-profile for the planetary boundary layer based
on large eddy simulation data. Bound.-Layer Meteor., 107,
401–427.
Ooyama, K., 1969: Numerical simulation of the life cycle of tropi-
cal cyclones. J. Atmos. Sci., 26, 3–40.
——, 1982: Conceptual evolution of the theory and modeling of
the tropical cyclone. J. Meteor. Soc. Japan, 60, 369–379.
Paulson, C. A., 1970: The mathematical representation of wind
speed and temperature profiles in the unstable atmospheric
surface layer. J. Appl. Meteor., 9, 857–861.
Perrie, W., E. L Andreas, W. Zhang, W. Li, J. Gyakum, and R.
McTaggart-Cowan, 2005: Sea spray impacts on intensifying
midlatitude cyclones. J. Atmos. Sci., 62, 1867–1883.
Persing, J., and M. T. Montgomery, 2003: Hurricane superinten-
sity. J. Atmos. Sci., 60, 2349–2371.
Powell, M. D., P. J. Vickery, and T. A. Reinhold, 2003: Reduced
drag coefficient for high wind speeds in tropical cyclones.
Nature, 422, 279–283.
Rogers, R., and Coauthors, 2006: The intensity forecasting experi-
ment: A NOAA multiyear field program for improving tropi-
cal cyclone intensity forecasts. Bull. Amer. Meteor. Soc., 87,1523–1537.
——, M. L. Black, S. S. Chen, and R. A. Black, 2007: An evalua-
tion of microphysics fields from mesoscale model simulations
of tropical cyclones. Part I: Comparisons with observations. J.
Atmos. Sci., 64, 1811–1834.
Rosenthal, S. L., 1971: The response of a tropical cyclone model
to variations in boundary layer parameters, initial conditions,
lateral boundary conditions, and domain size. Mon. Wea.
Rev., 99, 767–777.
Skamarock, W. C., J. B. Klemp, J. Dudhia, D. O. Gill, D. M.
Barker, W. Wang, and J. G. Powers, 2005: A description of
the Advanced Research WRF Version 2. NCAR Tech. Note
NCAR/TN-4681STR, 88 pp. [Available online at http://wrf-
model.org/wrfadmin/docs/arw_v2.pdf.]
Smith, S. D., 1980: Wind stress and heat flux over the ocean in
gale force winds. J. Phys. Oceanogr., 10, 709–726.
——, and Coauthors, 1992: Sea surface wind stress and drag co-
efficients: The HEXOS results. Bound.-Layer Meteor., 60,
109–142.
Tonkin, H., G. J. Holland, N. Holbrook, and A. Henderson-
Sellers, 2000: An evaluation of thermodynamic estimates of
climatological maximum potential tropical cyclone intensity.
Mon. Wea. Rev., 128, 746–762.
Webb, E. K., 1970: Profile relationships: The log-linear range, and
extension to strong stability. Quart. J. Roy. Meteor. Soc., 96, 67–90.
Wu, L., S. A. Braun, J. Halverson, and G. Heymsfield, 2006: A
numerical study of Hurricane Erin (2001). Part I: Model veri-
fication and storm evolution. J. Atmos. Sci., 63, 65–86.
Xiao, Q., X. Zou, and B. Wang, 2000: Initialization and simulation
of a landfalling hurricane using a variational bogus data as-
similation scheme. Mon. Wea. Rev., 128, 2252–2269.
Yang, B., Y. Wang, and B. Wang, 2007: The effect of internally
generated inner-core asymmetries on tropical cyclone poten-
tial intensity. J. Atmos. Sci., 64, 1165–1188.
Yelland, M. J., B. I. Moat, P. K. Taylor, R. W. Pascal, J. Hutch-
ings, and V. C. Cornell, 1998: Wind stress measurements
from the open ocean corrected for airflow distortion by the
ship. J. Phys. Oceanogr., 28, 1511–1526.
Zhang, D.-L., and R. A. Anthes, 1982: A high-resolution model of
the planetary boundary layer—Sensitivity tests and compari-
sons with SESAME-79 data. J. Appl. Meteor., 21, 1594–1609.
——, and X. Wang, 2003: Dependence of hurricane intensity and
structures on vertical resolution and time-step size. Adv. At-
mos. Sci., 20, 711–724.
Zou, X., and Q. Xiao, 2000: Studies on the initialization and sim-
ulation of a mature hurricane using a variational bogus data
assimilation scheme. J. Atmos. Sci., 57, 836–860.
FEBRUARY 2009 H I L L A N D L A C K M A N N 765