antenne andwrew 1.2m
TRANSCRIPT
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 1/12
I
E
H R
S
Tower Mount for 6ft (1.8m) Antennas.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
1 of 12page
Installation Instructions A CommScope Company
put barcode here
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement anyspecifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.
TMW Antenna
QA T
N
3
1 REFLECTOR ASSY
D
* = PART OF ACCESSORY KIT
TABLE 2- FASTENER TORQUE SPECIFICATIONS
TABLE 1- ANTENNA PARTS LIST
!
U-BOLT
E 2 BRACKET
G 1 PANNING FRAME ASSY
H 1 AZIMUTH ADJUSTER
I 1 ELEVATION ADJUSTER
N 11 M12x35mm HEX HEAD BOLT*
19 FLAT WASHER*
11
and zinc dust.regulations for petroleum products. Contents: oil, clay,partially filled containers according to governmentalopen near food or food sources. Dispose of empty oramounts of liquid soap and rinse with water. Do not storeaway from mouth. Wash thoroughly after use with liberalthe pre-applied conductive grease on threads. KeepWarning: Use protective wear to avoid skin contact with
results of improper or unsafe installation practices.Andrew disclaims any liability or responsibility for the
installation, maintenance, and condition of equipment.once a year by qualified personnel to verify propersuch personnel. Antenna systems should be inspectedAndrew installation instructions have been written forsystems requires qualified, experienced personnel.The installation, maintenance, or removal of antennaNotice
elevation adjustment.This mount provides ±20°azimuth or ±15°pipe of diameter 48 to 115 mm (1.9 to 4.5").assemble and fit the antenna mount to a vertical tower
The following pages show the steps required toDescription
SPRING WASHER*
11 M12 NUT*
Q 1 MOUNTING ANGLER 1 STRENGTHENING STRUT
S 1 STRUT PIPE
T 1 SAFETY BRACKET
Item Qty. DescriptionA
FastenerMaterial
Torque values in Nm (lb.ft)
Fastener size
- M5 M6 M8 M10 M12 M16
Stainless
Steel
4.5 7.7 18.7 39.2 65.1 161
(3.3) (5.7) (13.8) (28.9) (48) (18.7)
Galvanized2.7 4.5 11.1 22 38 95
(2.0) (3.3) (8.1) (16.2) (28) (70.1)
G
D
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 2/12
Mount Assembled onLeft Hand Side
Mount Assembled onRight Hand Side
showing appropriate sections
Note:-
only the left side assembly is described the right side assembly is identical except or
the antenna may be assembled with the mounts
Certain views have the antenna shields omitted for clarity.
the orientation of the strengthening strut - alternate steps and views will be shown.
on the right or the left side of the poles as shown.
The image shown canvary from product to product.Specific views will be display
Assembling the Mount
Tower Mount for 6ft (1.8m) Antennas.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
2 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement anyspecifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.
TMW Antenna
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 3/12
R.H.S. Assembly
Strengthening StrutStrengthening Strut
Orientation of Strengthening Strut Pipe on Mount
is fitted to the Top of the Reflector Backing Ring, as shown.
For mounts assembled on the Left Hand Side - the strengthening strut item (R)1.is fitted to the Bottom of Reflector Backing Ring, as shown.
For mounts assembled on the Right Hand Side - the strengthening strut item (R)2.
L.H.S. Assembly
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
3 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 4/12
tighten the bolts to the recommended torque.
1. Fit the mounting bracket (Q) to the backing ring usingfixing (N) tighten bolts to the recommended torque.
2. Fit the panning frame assy (G) to the mounting bracket (Q)using the fixings (N) tighten the bolts to the recommended torque.
L.H.S. Mount only.3. Fit the Strengthening Strut (R) to Mount using fixings (N)
Mount Assembly
N
TORQUE TO 38Nm
DETAIL BSCALE 1 : 10
G
R
N
N
TORQUE TO 38Nm
A
A
B
N
Q
DETAIL ASCALE 1 : 5
TORQUE TO 38Nm
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
4 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 5/12
C
TO THREADS
TORQUE TO 38Nm
DETAIL CSCALE 1 : 5
I
G
APPLY GREASE
ENSURE ELEVATIONADJUSTER IS FITTEDAT TOP OF MOUNT
for rotational movement whilst remaining securly attached.
Fit elevation adjuster (I) to the position shown on the mount (G).1.Tighten all bolts and nuts to the elevation adjuster securely enough to allow2.
Attaching the Elevation Adjuster
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
5 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 6/12
ATTACH SAFETY BRACKET
TORQUE TO 95Nm
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW ANTENNA
TOWER MOUNT FOR 6ft (1.8m) ANTENNAS.
6 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 7/12
D
SCALE 1 : 10DETAIL E
TORQUE TO 95Nm
TORQUE TO 95Nm
E
1. Lift the Antenna using the hoisting hole located on the backing ring
Never walk under hoisted loads
2.
Attach Antenna to the pole
fully tighten U-Bolts to recommeded torque.
Attach Mount to pole using U-Bolts,1.once in approximate position,
WARNING
Lifting the Antenna Mount on L.H.S.
Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
102344
DRE03 RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
7 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless SolutionsVisit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement anyspecifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.
Bulletin
DETAIL D
SCALE 1 : 15
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 8/12
SCALE 1 : 15DETAIL G
TORQUE TO 95Nm
TORQUE TO 95Nm
DETAIL FSCALE 1 : 15
G
F
Never walk under hoisted loads
2. Attach Strenthening Strut (R) to Mount using Fixings (N)
1. Lift the Antenna using the hoisting hole located on the backing ring
Attach Antenna to the pole
tighten the bolts to the recommended torque.
Attach Mount to pole using U-Bolts, once in approximate position,1. fully tighten U-Bolts to recommeded torque.
WARNING
Lifting the Antenna Mount on R.H.S.
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
8 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 9/12
H
DETAIL LSCALE 1 : 5
NUTS TO BE TIGHTTO BRACKETS
BRACKETS
ENSURE BRACKETS ANDNUTS ARE BOLTLY RIGIDLYTOGETHER AS SHOWN WITNO VISIBLE THREADS(VIEWED FROM UNDERSIDFOR CLARITY)
H
TOWER MEMBERDETAIL HSCALE 1 : 10
ES
APPLY GREASETO THREADS
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
9 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
2. Attach Strut Pipe (S) to Bracket wiht Fixing (N)3. Attach the Azimuth Adjuster (H) to the Strut Pipe (S).4. Attach the Azimuth Adjuster (H) to Tower member using the Pipe Clamp Bracket
Attaching the Azimuth Adjuster
fitted on Azimth Adjuster.
Assemble Brackets (E) together with Fixings (N), attach to Reflector Assembly,1.as shown with Fixings (N).
STRUT TO BE LOOSELY FITTEDUNTIL ALIGNMENT IS COMPLETETHEN TIGHTEN FIXINGS TORECOMMENDED TORQUE.
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 10/12
LOOSEN NUT/BOLTBEFORE ELEVATIONADJUSTMENT- RETORQUE TO 38Nm
±15°ADJUSTMENT
ELEVATION
TORQUE TO 38Nm
ENSURE SAFETYBRACKET ISSECURELY FITTEDAT ALL TIMES
3. Re-torque fixings once adjustemnt is complete.
Adjusting the Antenna in Elevation
Loosen the 5 bolts on the Panning Frame Assembly enough to allow for1.
rotational movement while remaining securley attached.Loosen the nuts on the Fine Elevation Adjuster and adjust the antennas signal,2.until the optimum signal is found. Tighten the nut on the Fine Adjuster by hand.
Antenna set-up and alignment
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
10 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 11/12
J
Note:
LOOSEN NUTS ONU-BOLT BEFOREAZ. ADJUSTMENT- RETORQUE TO 38Nm
prior to adjsutment.must be fittedStrengthening Strut (R)
±15°ADJUSTMENTAZIMUTH
TORQUE TO 95Nm
LOOSEN NUTSON BRACKETS BEFOREAZ. ADJUSTMENT- RETORQUE TO 38Nm
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
11 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
4. Repeat ELEVATION and AZIMUTH adjustments until optimum signal is found.
Loosen the U-Bolts enough to allow for rotational movement around the pole,1.while remaining securley attached.
2. Loosen the nuts on the Azimuth adjuster and adjust the antennas signal,until the optimum signal is found. Tighten the nut on the fine adjuster by hand.
3. Re-torque fixings once adjustemnt is complete.
Adjusting the Antenna in Azimuth
7/29/2019 Antenne Andwrew 1.2m
http://slidepdf.com/reader/full/antenne-andwrew-12m 12/12
25
525 5
K
TOWER
Clamp Bracket on
.
- P99915.Azimuth Adjuster
SCALE 1 : 10DETAIL K
MEMBER
S
TORQUE TO 38Nm
Attaching the clampbracket to the side strut
the angular limits shown in
Side Strut & Clamp Bracket installation
the illustrations.
NOTE:The side strut must beattached pointing directlybehind the antenna within
1. Tighten M12 U-Bolt sufficiently to allow for movement whilst remainingsecurely attached
Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.
102344
DRE03
Bulletin
RevStatusModel Version
Version RevStatus
TMW Antenna
Tower Mount for 6ft (1.8m) Antennas.
12 of 12page
Installation Instructions A CommScope Company
DRE03
Andrew Institute offers installation training.
Andrew Wireless Solutions
© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any
Other Europe: +44 592 782 612U.K.: 0800 250055or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours
specifications or warranties relating to Andrew Wireless Solutions products or services.
www.andrew.com
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, i nspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.