appendix3. spec data_rev.2
TRANSCRIPT
-
REV.2
CLASS 11020MR UOP: MS-1
BASIC MATERIAL CARBON STEEL ASME RATING CLASS 150 CORROSION ALLOWANCE 3 mm SERVICE UA Service Air
DA Dry Process Air NDE RT 5% PWHT - HARDNESS TEST - ADDITIONAL REQUIREMENTS - NOTES
NO DESCRIPTION
100 IN THE AVAILABLE SIZE RANGE BALL VALVES ARE PREFERRED TO GATE VALVES
101 PISTON TYPE CHECK VALVES (1/2 1 1/2), FOR HORIZONTAL MOUNTING ONLY.
105 IN LIEU OF GLOBE VALVES FOR SIZES NPS 8 & LARGER, GATE VALVES ARE PREFERRED TO BALL VALVES
USE OF SPECTACLE BLINDS, SPADE BLNIDS AND SPACERS SHALL BE IN ACCORDANCE WITH 5578-E1-SP-PU-016 (SPE 76/012)
300 BENDING OF PIPES SHALL ONLY BE DONE WHERE INDICATED IN THE PDS ELECTRONIC FILE, OTHERWISE WELDING ELBOWS SHALL BE USED. THE USE OF BENDING WILL BE MINIMIZED AND SUBJECT TO COMPANY APPROVAL.
FOR BENDING OF PIPE SEE 5578-E1-SP-PU-002
412 USE ONLY WHEN A FULL-PORT OPENING IN A BALL VALVE IS REQUIRED.
USE FLAT FACE FLANGES AGAINST GRE AND OTHER FLAT FACED PIPING COMPONENTS.
001 VALVES SHALL BE IN ACCORDANCE WITH REFERENCED DATA SHEET IN VALVE MATERIAL SPECIFICATIONS 5578-E1-SP-PU-201
003 THE MAX. DESIGN TEMPERATURE FOR BALL VALVES SHALL BE LIMITED TO 175 DEG. C.
031 TRANSIENT 145 DEG.C DESIGN TEMPERATURE
901 1 1/2 AND SMALLER FLANGED VALVES SHALL BE USED AGAINST FALNGED CONNECTIONS.
902 USE FOR DRAIN, VENT AND INSTRUMENT PIPING CONNECTIONS.
907 USE ONLY FOR EQUIPMENT CONNECTION OF HIGHER RATING.
910 USE LONG WELDING NECK FLANGES FOR TEMPERATURE CONNECTION OF PIPING
-
11020MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
1
5
1) SERVICE CODE: UA, DA- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
12
***** VALVES *****34
B GAT 0.5 - 1.5 GATE 800# SW A105N TR-410 BB,SPE 77/101,301,302,304 GA1755BGA175FA10B GATSWS 0.5 - 1.5902 GATE 800# SW/SCRD A105N TR-410 BB,SPE
77/101,301,302,304GA1755CGA175FA11
B GATFLG 0.5 - 1.5901 GATE 150# RF A105N TR-410 BB,SPE 77/101,301,302,304 GA4275DGA427FA12B GAT 2 - 12 GATE 150# RF A216-WCB TR-410 BB,SPE
77/102,301,302,304GA4275DGA427A15
B GAT 14 - 24 GATE 150# RF A216-WCB TR-410 BB GO,SPE 77/102,301,302,304
GA4275DGA427AG16
19B GLO 0.5 - 1.5 GLOBE 800# SW A105N TR-410 BB,SPE 77/101,301,302,304 GL1275BGL127FA21B GLO 2 - 6105 GLOBE 150# RF A216-WCB TR-410 BB,SPE
77/103,301,302,304GL4275DGL427A23
24B CHE 0.5 - 1.5101 CHECK 800# SW A105N TR-410 BC LIFT,SPE
77/101,301,302,304CH1135BCH113FA31
B CHE 2 - 4 CHECK 150# RF A216-WCB TR-410 BC SWING,SPE 77/104,301,302,304
CH6605DCH660A33
B CHE 6 - 24 CHECK 150# WAFER-LUG A216-WCB TR-410 DUAL PLT,SPE 77/133,301,302,304
CH6615DCH661A34
0033510039
B BAL 0.5 - 1.5 BALL 150# RF A105N,316-PTFE RED.BR FLOAT,SPE 77/100,301,302,304
BA4315DBA431FC41
B BAL 2 - 2 BALL 150# RF A216-WCB,316-PTFE RED.BR FLOAT,SPE 77/100,301,302,304
BA4315DBA431C42
B BAL 3 - 6 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION,SPE 77/100,301,302,304
BA4315DBA431CT43
B BAL 8 - 10 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION GO,SPE 77/100,301,302,304
BA4315DBA431CTG44
B BALF 0.5 - 1.5412 BALL 150# RF A105N,316-PTFE FULL BR FLOAT,SPE 77/100,301,302,304
BA4325DBA432FC45
B BALF 2 - 2412 BALL 150# RF A216-WCB,316-PTFE FULL BR FLOAT,SPE 77/100,301,302,304
BA4325DBA432C46
B BALF 3 - 6412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION,SPE 77/100,301,302,304
BA4325DBA432CT47
B BALF 8 - 10412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION GO,SPE 77/100,301,302,304
BA4325DBA432CTG48
9899
***** PIPE *****100101
PIP 0.5 - 1.5 PIPE SCH 80 SMLS A106-B PE, SPE 74/000,0025GCS080110
11020MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
2
5
1) SERVICE CODE: UA, DA- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
PIP 2 - 2 PIPE SCH 80 SMLS A106-B BE, SPE 74/000,0025GCS081111PIP 3 - 6 PIPE SCH 40 SMLS A106-B BE, SPE 74/000,0025GCS041112PIP 8 - 24 PIPE SCH 20 SMLS A106-B BE, SPE 74/000,0025GCS021113
148149
***** FITTINGS *****150152
ELL 0.5 - 1.5 ELL 90 DEG 3000# SW A105N, SPE 76/0005JAC10215445L 0.5 - 1.5 ELL 45 DEG 3000# SW A105N, SPE 76/0005JBC102156CAP 0.5 - 1.5 CAP 3000# SW A105N, SPE 76/0005JDC102158TEE 0.5 - 1.5 TEE 3000# SW A105N, SPE 76/0005JCC102162COU 0.5 - 1.5 COUPLING 3000# SW A105N, SPE 76/0005JGC102164PLG 0.5 - 1.5902 PLUG ROUND HEAD SCRD A105N, SPE 76/0005JFC004166
170BNIF 0.5 - 1.5 BRANCH FITTING FLANGED OUTLET 150# RF SCH 80 A105N
A=150MM, SPE 76/000,0315LRC108171
BNIP 0.5 - 1.5 BRANCH FITTING PLAIN END OUTLET 3000# SCH 80 A105N, SPE 76/000,031
5LSC108172
TOL 0.5 - 0.5902 THREADOLET 6000# A105N, SPE 76/0005LBC200173TOL 0.75 - 1.5902 THREADOLET 3000# A105N, SPE 76/0005LBC100174
178ELL 2 - 2 ELL 90 DEG LR SCH 80 A234 WPB, SPE 76/000,0035KACS0818045L 2 - 2 ELL 45 DEG SCH 80 A234 WPB, SPE 76/000,0035KCCS08181CAP 2 - 2 CAP SCH 80 A234 WPB, SPE 76/000,0035KHCS08182TEE 2 - 2 TEE SCH 80 A234 WPB, SPE 76/000,0035KDCS0808183TEE1 2 - 2 TEE SCH 40 X SCH 80 A234 WPB, SPE 76/000,0035KDCS0408184REDCB1 2 - 2 REDUCER CONC SCH 40 X SCH 80 A234 WPB, SPE 76/000,0035KFCS0408188REDEB1 2 - 2 REDUCER ECC SCH 40 X SCH 80 A234 WPB, SPE 76/000,0035KGCS0408190
192194
ELL 3 - 6 ELL 90 DEG LR SCH 40 A234 WPB, SPE 76/000,0035KACS0420045L 3 - 6 ELL 45 DEG SCH 40 A234 WPB, SPE 76/000,0035KCCS04202CAP 3 - 6 CAP SCH 40 A234 WPB, SPE 76/000,0035KHCS04203TEE 3 - 6 TEE SCH 40 A234 WPB, SPE 76/000,0035KDCS0404204TEE1 6 - 6 TEE SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KDCS0204206REDCBW 3 - 4 REDUCER CONC SCH 40 A234 WPB, SPE 76/000,0035KFCS0404208REDCB1 4 - 6 REDUCER CONC SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KFCS0204209
11020MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
3
5
1) SERVICE CODE: UA, DA- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
REDEBW 3 - 4 REDUCER ECC SCH 40 A234 WPB, SPE 76/000,0035KGCS0404210REDEB1 4 - 6 REDUCER ECC SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KGCS0204211
218ELL 8 - 18 ELL 90 DEG LR SCH 20 A234 WPB, SPE 76/000,0035KACS0222045L 8 - 18 ELL 45 DEG SCH 20 A234 WPB, SPE 76/000,0035KCCS02222CAP 8 - 18 CAP SCH 20 A234 WPB, SPE 76/000,0035KHCS02223TEE 8 - 18 TEE SCH 20 A234 WPB, SPE 76/000,0035KDCS0202224TEE1 18 - 18 TEE SCH 20 A234 WPBW, SPE 76/000,0035KDCW0202225REDCBW 8 - 16 REDUCER CONC SCH 20 A234 WPB, SPE 76/000,0035KFCS0202228REDCB1 12 - 18 REDUCER CONC SCH 20 A234 WPBW, SPE 76/000,0035KFCW0202229REDEBW 8 - 16 REDUCER ECC SCH 20 A234 WPB, SPE 76/000,0035KGCS0202230REDEB1 12 - 18 REDUCER ECC SCH 20 A234 WPBW, SPE 76/000,0035KGCW0202231
239ELL 20 - 24 ELL 90 DEG LR SCH 20 A234 WPBW, SPE 76/000,0035KACW0224045L 20 - 24 ELL 45 DEG SCH 20 A234 WPBW, SPE 76/000,0035KCCW02241CAP 20 - 24 CAP SCH 20 A234 WPB, SPE 76/000,0035KHCS02242TEE 20 - 24 TEE SCH 20 A234 WPBW, SPE 76/000,0035KDCW0202243
B REDCBW 20 - 20 REDUCER CONC SCH 20 A234 WPBW, SPE 76/000,0035KFCW0202244B REDEBW 20 - 20 REDUCER ECC SCH 20 A234 WPBW, SPE 76/000,0035KGCW0202245
298299
***** FLANGES *****300301
FLG 0.5 - 1.5 FLG SW 150# RF SCH 80 BORE A105N, SPE 76/000,0025NQC108302FLG 2 - 2 FLG WN 150# RF SCH 80 BORE A105N, SPE 76/000,0025NNC108303FLG 3 - 6 FLG WN 150# RF SCH 40 BORE A105N, SPE 76/000,0025NNC104304FLG 8 - 24 FLG WN 150# RF SCH 20 BORE A105N, SPE 76/000,0025NNC102305
306FLGJS 6 - 6 FLG WN 150# RF SCH 40 BORE A105N W/JACK SCREW, SPE
76/000,0025NMC104310
FLGJS 8 - 24 FLG WN 150# RF SCH 20 BORE A105N W/JACK SCREW, SPE 76/000,002
5NMC102311
319FLG300 0.5 - 1.5907 FLG SW 300# RF SCH 80 BORE A105N, SPE 76/000,0025NQC208320FLG300 2 - 2907 FLG WN 300# RF SCH 80 BORE A105N, SPE 76/000,0025NNC208321FLG300 3 - 6907 FLG WN 300# RF SCH 40 BORE A105N, SPE 76/000,0025NNC204322FLG300 8 - 24907 FLG WN 300# RF SCH 20 BORE A105N, SPE 76/000,0025NNC202324
11020MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
4
5
1) SERVICE CODE: UA, DA- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
329BLF 0.5 - 24 FLG BLIND 150# RF A105N, SPE 76/000,0025NFC100330BLF300 0.5 - 24907 FLG BLIND 300# RF A105N, SPE 76/000,0025NFC200332
339FLGLWN 1.5 - 1.5910 FLG LONG WN 300# RF A105N L=6", SPE 76/000,0025NYC200340
348349
***** ORIFICE FLANGES *****350351
B ORI 2 - 2 WN ORIF SET 300# RF SCH 80 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC208360
B ORI 3 - 6 WN ORIF SET 300# RF SCH 40 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC204361
B ORI 8 - 14 WN ORIF SET 300# RF SCH 20 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC202362
398399
***** PIPE NIPPLES *****400402
NIPPB3 0.5 - 1.5 NIPPLE SCH 80 A106-B, SPE 74/000,002,76/000 PBE 3"-LONG
5MAC308410
NIPPB6 0.5 - 1.5 NIPPLE SCH 80 A106-B, SPE 74/000,002,76/000 PBE 6"-LONG
5MAC608412
414NIPTB3 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000
TBE 3"-LONG5MBC318420
NIPTB3 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TBE 3"-LONG
5MBC316422
NIPTB6 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000 TBE 6"-LONG
5MBC618424
NIPTB6 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TBE 6"-LONG
5MBC616426
428NIPTO3 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000
TOE 3"-LONG5MCC318430
NIPTO3 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TOE 3"-LONG
5MCC316432
NIPTO6 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000 TOE 6"-LONG
5MCC618434
NIPTO6 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TOE 6"-LONG
5MCC616436
440450
***** SWAGE NIPPLES *****451452
11020MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
5
5
1) SERVICE CODE: UA, DA- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
SWACPE 0.5 - 1 SWAGE CONC SCH 80 A234 WPB, SPE 76/000,003 PBE
5MMC0808460
SWACBE 0.5 - 1.5 SWAGE CONC SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MFC0808462
SWACB1 0.5 - 1.5 SWAGE CONC SCH 40 X SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MFC0408464
468SWAEPE 0.5 - 1 SWAGE ECC SCH 80 A234 WPB, SPE 76/000,003
PBE5MVC0808480
SWAEBE 0.5 - 1.5 SWAGE ECC SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MPC0808482
SWAEB1 0.5 - 1.5 SWAGE ECC SCH 40 X SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MPC0408484
498499
***** GASKETS *****500501
GAS 0.5 - 24 GASKET 150# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR110510
GAS300 0.5 - 24907 GASKET 300# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR210512
5191 ISOKIT 0.5 - 24 ISOLATION KIT 150# RF TYPE-F 1/8" TK5RLA100520
548549
***** BOLTING *****550551
BOL 50 - 1500 STUD-BOLT A193 GR B7 W/A194 GR 2H NUTS, FLOUROCARBON POLYMER COATED(TAKECOAT-1000 OR EQUAL)
5UBB001560
562564
***** SPECTACLE BLIND *****600601
SPEBLD 0.5 - 12 BLIND SPECTACLE 150# RF A516-65, SPE 76/000,0125NGC100610619
BLDPAD 14 - 24 BLIND PADDLE 150# RF A516-65, SPE 76/000,0125NHC100620SPAPAD 14 - 24 SPACER PADDLE 150# RF A516-65, SPE 76/000,0125NJC100621
11020MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
6
5
1) SERVICE CODE: UA, DA- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
PIPING BRANCH REINFORCENMENT REQUIREMENT
1/4
2 1/2
1 1/2
1/2
3/4
1
2
3
4
6
8
10
12
14
16
18
20
24
A
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
A
B
B
C
C
C
C
C
C
C
C
C
C
C
C
A
B
C
C
C
C
C
C
C
C
C
C
C
C
A
C
C
C
C
C
C
C
C
C
C
C
C
A
B
D
D
D
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
A
B
D
D
D
D
D
A
B
D
D
D
D
A
B
D
D
D
A
B
D
D
A
B
D
A
B A
H
A
D
E
R
S
I
Z
E
N
P
S
(IN)
242018 1614 1210 8 1/4 1/2 3/4 1 1 1/2 2 2 1/2 3 4 6
B R A N C H S I Z E ( N P S - I N C H )
E
1. ABBREVIATIONS. A : EQUAL TEE B : REDUCING TEE C : BRANCH FITTING PLAIN-END OUTLET D : PIPE TO PIPE (STUB-ON) E : BRANCH OUTLET REDUCING BUTT-WELD (WELDOLET) 2. STUB-ON SHALL BE REINFORCED IN ACCORDANCE WITH ASME B31.3 Para.304.3 WHERE REINFORCING TO BE REQUIRED.
11020MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
REV.2
CLASS 11020MRE UNDERGROUND PIPING for 11020MR UOP: MS-1
BASIC MATERIAL CARBON STEEL ASME RATING CLASS 150 CORROSION ALLOWANCE 3 mm SERVICE UA Service Air
DA Dry Process Air NDE RT 5% PWHT - HARDNESS TEST - ADDITIONAL REQUIREMENTS 1) COATING & WRAPPING
UNDERGROUND STEEL PIPING SHALL BE PROTECTED AGAINST SOIL CORROSION IN ACCORDANCE WITH 5578-E1-SP-MY-001
NOTES
NO DESCRIPTION
100 IN THE AVAILABLE SIZE RANGE BALL VALVES ARE PREFERRED TO GATE VALVES
101 PISTON TYPE CHECK VALVES (1/2 1 1/2), FOR HORIZONTAL MOUNTING ONLY.
105 IN LIEU OF GLOBE VALVES FOR SIZES NPS 8 & LARGER, GATE VALVES ARE PREFERRED TO BALL VALVES
USE OF SPECTACLE BLINDS, SPADE BLNIDS AND SPACERS SHALL BE IN ACCORDANCE WITH 5578-E1-SP-PU-016 (SPE 76/012)
300 BENDING OF PIPES SHALL ONLY BE DONE WHERE INDICATED IN THE PDS ELECTRONIC FILE, OTHERWISE WELDING ELBOWS SHALL BE USED. THE USE OF BENDING WILL BE MINIMIZED AND SUBJECT TO COMPANY APPROVAL.
FOR BENDING OF PIPE SEE 5578-E1-SP-PU-002
412 USE ONLY WHEN A FULL-PORT OPENING IN A BALL VALVE IS REQUIRED.
USE FLAT FACE FLANGES AGAINST GRE AND OTHER FLAT FACED PIPING COMPONENTS.
001 VALVES SHALL BE IN ACCORDANCE WITH REFERENCED DATA SHEET IN VALVE MATERIAL SPECIFICATIONS 5578-E1-SP-PU-201
003 THE MAX. DESIGN TEMPERATURE FOR BALL VALVES SHALL BE LIMITED TO 175 DEG. C.
031 TRANSIENT 145 DEG.C DESIGN TEMPERATURE 901 1 1/2 AND SMALLER FLANGED VALVES SHALL BE USED AGAINST FALNGED CONNECTIONS. 902 USE FOR DRAIN, VENT AND INSTRUMENT PIPING CONNECTIONS. 907 USE ONLY FOR EQUIPMENT CONNECTION OF HIGHER RATING. 910 USE LONG WELDING NECK FLANGES FOR TEMPERATURE CONNECTION OF PIPING
-
11020MRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
1
5
1) SERVICE CODE: UA, DA2) COAT & WRAP (5578-E1-SP-MY-001)- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
14
***** VALVES *****89
B GAT 0.5 - 1.5 GATE 800# SW A105N TR-410 BB,SPE 77/101,301,302,304 GA1755BGA175FA10B GATSWS 0.5 - 1.5902 GATE 800# SW/SCRD A105N TR-410 BB,SPE
77/101,301,302,304GA1755CGA175FA11
B GATFLG 0.5 - 1.5901 GATE 150# RF A105N TR-410 BB,SPE 77/101,301,302,304 GA4275DGA427FA12B GAT 2 - 12 GATE 150# RF A216-WCB TR-410 BB,SPE
77/102,301,302,304GA4275DGA427A15
B GAT 14 - 24 GATE 150# RF A216-WCB TR-410 BB GO,SPE 77/102,301,302,304
GA4275DGA427AG16
17B GLO 0.5 - 1.5 GLOBE 800# SW A105N TR-410 BB,SPE 77/101,301,302,304 GL1275BGL127FA21B GLO 2 - 6105 GLOBE 150# RF A216-WCB TR-410 BB,SPE
77/103,301,302,304GL4275DGL427A23
24B CHE 0.5 - 1.5101 CHECK 800# SW A105N TR-410 BC LIFT,SPE
77/101,301,302,304CH1135BCH113FA31
B CHE 2 - 4 CHECK 150# RF A216-WCB TR-410 BC SWING,SPE 77/104,301,302,304
CH6605DCH660A33
B CHE 6 - 24 CHECK 150# WAFER-LUG A216-WCB TR-410 DUAL PLT,SPE 77/133,301,302,304
CH6615DCH661A34
0033510039
B BAL 0.5 - 1.5 BALL 150# RF A105N,316-PTFE RED.BR FLOAT,SPE 77/100,301,302,304
BA4315DBA431FC41
B BAL 2 - 2 BALL 150# RF A216-WCB,316-PTFE RED.BR FLOAT,SPE 77/100,301,302,304
BA4315DBA431C42
B BAL 3 - 6 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION,SPE 77/100,301,302,304
BA4315DBA431CT43
B BAL 8 - 10 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION GO,SPE 77/100,301,302,304
BA4315DBA431CTG44
0 BALF 0.5 - 1.5412 BALL 150# RF A105N,316-PTFE FULL BR FLOAT,SPE 77/100,301,302,304
BA4325DBA432FC45
0 BALF 2 - 2412 BALL 150# RF A216-WCB,316-PTFE FULL BR FLOAT,SPE 77/100,301,302,304
BA4325DBA432C46
0 BALF 3 - 6412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION,SPE 77/100,301,302,304
BA4325DBA432CT47
0 BALF 8 - 10412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION GO,SPE 77/100,301,302,304
BA4325DBA432CTG48
9899
***** PIPE *****100101
11020MRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
2
5
1) SERVICE CODE: UA, DA2) COAT & WRAP (5578-E1-SP-MY-001)- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
PIP 0.5 - 1.5 PIPE SCH 80 SMLS A106-B PE, SPE 74/000,002, 3LPE-COATED
5GCS080U105
PIP 2 - 2 PIPE SCH 80 SMLS A106-B BE, SPE 74/000,002, 3LPE-COATED
5GCS081U106
PIP 3 - 6 PIPE SCH 40 SMLS A106-B BE, SPE 74/000,002, 3LPE-COATED
5GCS041U107
1 PIP 8 - 24 PIPE SCH 20 SMLS A106-B BE, SPE 74/000,002, 3LPE-COATED
5GCS021U108
114149
***** FITTINGS *****150152
ELL 0.5 - 1.5 ELL 90 DEG 3000# SW A105N, SPE 76/0005JAC10215445L 0.5 - 1.5 ELL 45 DEG 3000# SW A105N, SPE 76/0005JBC102156CAP 0.5 - 1.5 CAP 3000# SW A105N, SPE 76/0005JDC102158TEE 0.5 - 1.5 TEE 3000# SW A105N, SPE 76/0005JCC102162COU 0.5 - 1.5 COUPLING 3000# SW A105N, SPE 76/0005JGC102164PLG 0.5 - 1.5902 PLUG ROUND HEAD SCRD A105N, SPE 76/0005JFC004166
170BNIF 0.5 - 1.5 BRANCH FITTING FLANGED OUTLET 150# RF SCH 80 A105N
A=150MM, SPE 76/000,0315LRC108171
BNIP 0.5 - 1.5 BRANCH FITTING PLAIN END OUTLET 3000# SCH 80 A105N, SPE 76/000,031
5LSC108172
TOL 0.5 - 0.5902 THREADOLET 6000# A105N, SPE 76/0005LBC200173TOL 0.75 - 1.5902 THREADOLET 3000# A105N, SPE 76/0005LBC100174
178ELL 2 - 2 ELL 90 DEG LR SCH 80 A234 WPB, SPE 76/000,0035KACS0818045L 2 - 2 ELL 45 DEG SCH 80 A234 WPB, SPE 76/000,0035KCCS08181CAP 2 - 2 CAP SCH 80 A234 WPB, SPE 76/000,0035KHCS08182TEE 2 - 2 TEE SCH 80 A234 WPB, SPE 76/000,0035KDCS0808183TEE1 2 - 2 TEE SCH 40 X SCH 80 A234 WPB, SPE 76/000,0035KDCS0408184REDCB1 2 - 2 REDUCER CONC SCH 40 X SCH 80 A234 WPB, SPE 76/000,0035KFCS0408188REDEB1 2 - 2 REDUCER ECC SCH 40 X SCH 80 A234 WPB, SPE 76/000,0035KGCS0408190
192194
ELL 3 - 6 ELL 90 DEG LR SCH 40 A234 WPB, SPE 76/000,0035KACS0420045L 3 - 6 ELL 45 DEG SCH 40 A234 WPB, SPE 76/000,0035KCCS04202CAP 3 - 6 CAP SCH 40 A234 WPB, SPE 76/000,0035KHCS04203TEE 3 - 6 TEE SCH 40 A234 WPB, SPE 76/000,0035KDCS0404204TEE1 6 - 6 TEE SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KDCS0204206
11020MRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
3
5
1) SERVICE CODE: UA, DA2) COAT & WRAP (5578-E1-SP-MY-001)- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
REDCBW 3 - 4 REDUCER CONC SCH 40 A234 WPB, SPE 76/000,0035KFCS0404208REDCB1 4 - 6 REDUCER CONC SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KFCS0204209REDEBW 3 - 4 REDUCER ECC SCH 40 A234 WPB, SPE 76/000,0035KGCS0404210REDEB1 4 - 6 REDUCER ECC SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KGCS0204211
218ELL 8 - 18 ELL 90 DEG LR SCH 20 A234 WPB, SPE 76/000,0035KACS0222045L 8 - 18 ELL 45 DEG SCH 20 A234 WPB, SPE 76/000,0035KCCS02222CAP 8 - 18 CAP SCH 20 A234 WPB, SPE 76/000,0035KHCS02223TEE 8 - 18 TEE SCH 20 A234 WPB, SPE 76/000,0035KDCS0202224TEE1 18 - 18 TEE SCH 20 A234 WPBW, SPE 76/000,0035KDCW0202225REDCBW 8 - 16 REDUCER CONC SCH 20 A234 WPB, SPE 76/000,0035KFCS0202228REDCB1 12 - 18 REDUCER CONC SCH 20 A234 WPBW, SPE 76/000,0035KFCW0202229REDEBW 8 - 16 REDUCER ECC SCH 20 A234 WPB, SPE 76/000,0035KGCS0202230REDEB1 12 - 18 REDUCER ECC SCH 20 A234 WPBW, SPE 76/000,0035KGCW0202231
239ELL 20 - 24 ELL 90 DEG LR SCH 20 A234 WPBW, SPE 76/000,0035KACW0224045L 20 - 24 ELL 45 DEG SCH 20 A234 WPBW, SPE 76/000,0035KCCW02241CAP 20 - 24 CAP SCH 20 A234 WPB, SPE 76/000,0035KHCS02242TEE 20 - 24 TEE SCH 20 A234 WPBW, SPE 76/000,0035KDCW0202243REDCBW 20 - 20 REDUCER CONC SCH 20 A234 WPBW, SPE 76/000,0035KFCW0202244REDEBW 20 - 20 REDUCER ECC SCH 20 A234 WPBW, SPE 76/000,0035KGCW0202245
298299
***** FLANGES *****300301
FLG 0.5 - 1.5 FLG SW 150# RF SCH 80 BORE A105N, SPE 76/000,0025NQC108302FLG 2 - 2 FLG WN 150# RF SCH 80 BORE A105N, SPE 76/000,0025NNC108303FLG 3 - 6 FLG WN 150# RF SCH 40 BORE A105N, SPE 76/000,0025NNC104304FLG 8 - 24 FLG WN 150# RF SCH 20 BORE A105N, SPE 76/000,0025NNC102305
306FLGJS 6 - 6 FLG WN 150# RF SCH 40 BORE A105N W/JACK SCREW, SPE
76/000,0025NMC104310
FLGJS 8 - 24 FLG WN 150# RF SCH 20 BORE A105N W/JACK SCREW, SPE 76/000,002
5NMC102311
319FLG300 0.5 - 1.5907 FLG SW 300# RF SCH 80 BORE A105N, SPE 76/000,0025NQC208320FLG300 2 - 2907 FLG WN 300# RF SCH 80 BORE A105N, SPE 76/000,0025NNC208321
11020MRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
4
5
1) SERVICE CODE: UA, DA2) COAT & WRAP (5578-E1-SP-MY-001)- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
FLG300 3 - 6907 FLG WN 300# RF SCH 40 BORE A105N, SPE 76/000,0025NNC204322FLG300 8 - 24907 FLG WN 300# RF SCH 20 BORE A105N, SPE 76/000,0025NNC202324
329BLF 0.5 - 24 FLG BLIND 150# RF A105N, SPE 76/000,0025NFC100330BLF300 0.5 - 24907 FLG BLIND 300# RF A105N, SPE 76/000,0025NFC200332
339FLGLWN 1.5 - 1.5910 FLG LONG WN 300# RF A105N L=6", SPE 76/000,0025NYC200340
348349
***** ORIFICE FLANGES *****350351
B ORI 2 - 2 WN ORIF SET 300# RF SCH 80 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC208360
B ORI 3 - 6 WN ORIF SET 300# RF SCH 40 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC204361
B ORI 8 - 24 WN ORIF SET 300# RF SCH 20 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC202362
398399
***** PIPE NIPPLES *****400402
NIPPB3 0.5 - 1.5 NIPPLE SCH 80 A106-B, SPE 74/000,002,76/000 PBE 3"-LONG
5MAC308410
NIPPB6 0.5 - 1.5 NIPPLE SCH 80 A106-B, SPE 74/000,002,76/000 PBE 6"-LONG
5MAC608412
414NIPTB3 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000
TBE 3"-LONG5MBC318420
NIPTB3 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TBE 3"-LONG
5MBC316422
NIPTB6 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000 TBE 6"-LONG
5MBC618424
NIPTB6 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TBE 6"-LONG
5MBC616426
428NIPTO3 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000
TOE 3"-LONG5MCC318430
NIPTO3 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TOE 3"-LONG
5MCC316432
NIPTO6 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000 TOE 6"-LONG
5MCC618434
NIPTO6 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TOE 6"-LONG
5MCC616436
440
11020MRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
5
5
1) SERVICE CODE: UA, DA2) COAT & WRAP (5578-E1-SP-MY-001)- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
450***** SWAGE NIPPLES *****451
452SWACPE 0.5 - 1 SWAGE CONC SCH 80 A234 WPB, SPE 76/000,003
PBE5MMC0808460
SWACBE 0.5 - 1.5 SWAGE CONC SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MFC0808462
SWACB1 0.5 - 1.5 SWAGE CONC SCH 40 X SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MFC0408464
468SWAEPE 0.5 - 1 SWAGE ECC SCH 80 A234 WPB, SPE 76/000,003
PBE5MVC0808480
SWAEBE 0.5 - 1.5 SWAGE ECC SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MPC0808482
SWAEB1 0.5 - 1.5 SWAGE ECC SCH 40 X SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MPC0408484
498499
***** GASKETS *****500501
GAS 0.5 - 24 GASKET 150# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR110510
GAS300 0.5 - 24907 GASKET 300# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR210512
548549
***** BOLTING *****550551
BOL 50 - 1500 STUD-BOLT A193 GR B7 W/A194 GR 2H NUTS, FLOUROCARBON POLYMER COATED(TAKECOAT-1000 OR EQUAL)
5UBB001560
562564
***** SPECTACLE BLIND *****600601
SPEBLD 0.5 - 12 BLIND SPECTACLE 150# RF A516-65, SPE 76/000,0125NGC100610619
BLDPAD 14 - 24 BLIND PADDLE 150# RF A516-65, SPE 76/000,0125NHC100620SPAPAD 14 - 24 SPACER PADDLE 150# RF A516-65, SPE 76/000,0125NJC100621
11020MRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11020MRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
6
5
1) SERVICE CODE: UA, DA2) COAT & WRAP (5578-E1-SP-MY-001)- TRANSIENT 145 DESIGN TEMP.- UOP(MS-1)
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 65
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:5% HARDNESS - REMARK
PIPING BRANCH REINFORCENMENT REQUIREMENT
1/4
2 1/2
1 1/2
1/2
3/4
1
2
3
4
6
8
10
12
14
16
18
20
24
A
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
A
B
B
C
C
C
C
C
C
C
C
C
C
C
C
A
B
C
C
C
C
C
C
C
C
C
C
C
C
A
C
C
C
C
C
C
C
C
C
C
C
C
A
B
D
D
D
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
D
A
B
D
D
D
D
D
D
A
B
D
D
D
D
D
A
B
D
D
D
D
A
B
D
D
D
A
B
D
D
A
B
D
A
B A
H
A
D
E
R
S
I
Z
E
N
P
S
(IN)
242018 1614 1210 8 1/4 1/2 3/4 1 1 1/2 2 2 1/2 3 4 6
B R A N C H S I Z E ( N P S - I N C H )
E
1. ABBREVIATIONS. A : EQUAL TEE B : REDUCING TEE C : BRANCH FITTING PLAIN-END OUTLET D : PIPE TO PIPE (STUB-ON) E : BRANCH OUTLET REDUCING BUTT-WELD (WELDOLET) 2. STUB-ON SHALL BE REINFORCED IN ACCORDANCE WITH ASME B31.3 Para.304.3 WHERE REINFORCING TO BE REQUIRED.
11020MRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
REV.2
CLASS 11025XR
BASIC MATERIAL CARBON STEEL, LSS ASME RATING CLASS 150 CORROSION ALLOWANCE 3 mm SERVICE P Lean Amine
P Lean Amine w/H2S(H2S
-
11025XR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
1
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004)
M A T E R I A L
CS A106-B, LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
15
***** VALVES *****89
B GAT 0.5 - 1.5 GATE 800# SW A105N TR-410 BB,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305
GA0115BGA011FA08P10
B GATSWS 0.5 - 1.5902 GATE 800# SW/SCRD A105N TR-410 BB,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305
GA0125CGA012FA08P11
1 GATPTS 0.5 - 0.5950 GATE 800# SW/SCRD A105N TR-410 BB,W/NIP-TE(100MM,XXS)PWHT,LSS,SPE 77/101,301,303,305
GA0125CGA012FA18S12
1 GATPT8 0.5 - 0.5950 GATE 800# SW/SCRD A105N TR-410 BB,W/NIP-TE(200MM,XXS)PWHT,LSS,SPE 77/101,301,303,305
GA0125CGA012FA19S13
B GATFLG 0.5 - 1.5901 GATE 150# RF A105N TR-410 BB,LSS,SPE 77/101,301,303,305
GA3115DGA311FA14
B GAT 2 - 6 GATE 150# RF A216-WCB TR-410 BB,LSS,SPE 77/102,301,303,305
GA3115DGA311A15
1 GAT300 2 - 2964 GATE 300# RF A216-WCB TR-410 BB,LSS,SPE 77/102,301,303,305
GA3395DGA339A17
19B GLO 0.5 - 1.5 GLOBE 800# SW A105N TR-410 STEL
BB,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305GL0115BGL011FB08P21
B GLO 2 - 6105 GLOBE 150# RF A216-WCB TR-410 STEL BB,LSS,SPE 77/103,301,303,305
GL3115DGL311B23
24B CHE 0.5 - 1.5101 CHECK 800# SW A105N TR-410 BC
LIFT,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305CH0115BCH011FA08P31
B CHE 2 - 4 CHECK 150# RF A216-WCB TR-410 BC SWING,LSS,SPE 77/104,301,303,305
CH3125DCH312A33
B CHE 6 - 6 CHECK 150# WAFER-LUG A216-WCB TR-410 DUAL PLT,LSS,SPE 77/133,301,303,305
CH3135DCH313A34
0033510039
B BAL 0.5 - 1.5 BALL 150# RF A105N,316-PTFE RED.BR FLOAT,LSS,SPE 77/100,301,303,305
BA3115DBA311FC41
B BAL 2 - 2 BALL 150# RF A216-WCB,316-PTFE RED.BR FLOAT,LSS,SPE 77/100,301,303,305
BA3115DBA311C42
B BAL 3 - 6 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION,LSS,SPE 77/100,301,303,305
BA3115DBA311CT43
B BALF 0.5 - 1.5412 BALL 150# RF A105N,316-PTFE FULL BR FLOAT,LSS,SPE 77/100,301,303,305
BA3125DBA312FC45
B BALF 2 - 2412 BALL 150# RF A216-WCB,316-PTFE FULL BR FLOAT,LSS,SPE 77/100,301,303,305
BA3125DBA312C46
B BALF 3 - 6412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION,LSS,SPE 77/100,301,303,305
BA3125DBA312CT47
9899
***** PIPE *****100101
11025XR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
2
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004)
M A T E R I A L
CS A106-B, LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
PIP 0.5 - 1.5 PIPE SCH 80 SMLS A106-B PE, LSS, SPE 74/000,002, MW-004
5GCS080L110
PIP 2 - 2 PIPE SCH 80 SMLS A106-B BE, LSS, SPE 74/000,002, MW-004
5GCS081L111
PIP 3 - 6 PIPE SCH 40 SMLS A106-B BE, LSS, SPE 74/000,002, MW-004
5GCS041L112
148149
***** FITTINGS *****150151
ELL 0.5 - 1.5 ELL 90 DEG 3000# SW A105N, LSS, SPE 76/000, MW-0045JAC102L16045L 0.5 - 1.5 ELL 45 DEG 3000# SW A105N, LSS, SPE 76/000, MW-0045JBC102L161CAP 0.5 - 1.5 CAP 3000# SW A105N, LSS, SPE 76/000, MW-0045JDC102L162TEE 0.5 - 1.5 TEE 3000# SW A105N, LSS, SPE 76/000, MW-0045JCC102L163COU 0.5 - 1.5 COUPLING 3000# SW A105N, LSS, SPE 76/000, MW-0045JGC102L165PLG 0.5 - 1.5902 PLUG ROUND HEAD SCRD A105N, LSS, SPE 76/000, MW-0045JFC004L166
170BNIF 0.5 - 1.5 BRANCH FITTING FLANGED OUTLET 150# RF SCH 80 A105N
A=150MM, LSS, SPE 76/000,031, MW-0045LRC108L171
BNIP 0.5 - 1.5 BRANCH FITTING PLAIN END OUTLET 3000# SCH 80 A105N, LSS, SPE 76/000,031, MW-004
5LSC108L172
1 SOL 0.5 - 1.5903 SOCKOLET 3000# A105N, LSS, SPE 76/000, MW-0045LCC100L173TOL 0.5 - 0.5902 THREADOLET 6000# A105N, LSS, SPE 76/000, MW-0045LBC200L175TOL 0.75 - 1.5902 THREADOLET 3000# A105N, LSS, SPE 76/000, MW-0045LBC100L178
180ELL 2 - 2 ELL 90 DEG LR SCH 80 A234 WPB, LSS, SPE 76/000,003,
MW-0045KACS08L181
45L 2 - 2 ELL 45 DEG SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004
5KCCS08L182
CAP 2 - 2 CAP SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-0045KHCS08L183TEE 2 - 2 TEE SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-0045KDCS0808L184TEE1 2 - 2 TEE SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003,
MW-0045KDCS0408L186
REDCB1 2 - 2 REDUCER CONC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004
5KFCS0408L190
REDEB1 2 - 2 REDUCER ECC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004
5KGCS0408L192
WOL1 2 - 2 WELDOLET SCH 40 X SCH 80 A105N, LSS, SPE 76/000,030, MW-004
5LAC0408L194
195239
ELL 3 - 6 ELL 90 DEG LR SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-004
5KACS04L240
45L 3 - 6 ELL 45 DEG SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-004
5KCCS04L241
11025XR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
3
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004)
M A T E R I A L
CS A106-B, LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
CAP 3 - 6 CAP SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-0045KHCS04L242TEE 3 - 6 TEE SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-0045KDCS0404L243REDCBW 3 - 4 REDUCER CONC SCH 40 A234 WPB, LSS, SPE 76/000,003,
MW-0045KFCS0404L247
REDEBW 3 - 4 REDUCER ECC SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-004
5KGCS0404L248
298299
***** FLANGES *****300301
FLG 0.5 - 1.5 FLG SW 150# RF SCH 80 BORE A105N, LSS, SPE 76/000,002, MW-004
5NQC108L302
FLG 2 - 2 FLG WN 150# RF SCH 80 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC108L303
FLG 3 - 6 FLG WN 150# RF SCH 40 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC104L304
305FLGJS 6 - 6 FLG WN 150# RF SCH 40 BORE A105N W/JACK SCREW, LSS,
SPE 76/000,002, MW-0045NMC104L310
319FLG300 0.5 - 1.5907 FLG SW 300# RF SCH 80 BORE A105N, LSS, SPE
76/000,002, MW-0045NQC208L320
FLG300 2 - 2907 FLG WN 300# RF SCH 80 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC208L321
FLG300 3 - 6907 FLG WN 300# RF SCH 40 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC204L322
329BLF 0.5 - 6 FLG BLIND 150# RF A105N, LSS, SPE 76/000,002, MW-0045NFC100L330BLF300 0.5 - 6907 FLG BLIND 300# RF A105N, LSS, SPE 76/000,002, MW-0045NFC200L332
339FLGLWN 1.5 - 1.5910 FLG LONG WN 300# RF A105N L=6", LSS, SPE 76/000,002,
MW-0045NYC200L340
348349
***** ORIFICE FLANGES *****350351
B ORI 2 - 2 WN ORIF SET 300# RF SCH 80 BORE A105N, 1/2"-NPT TWO-TAPS, LSS, SPE 76/000,025, MW-004
5NPC208L361
B ORI 3 - 6 WN ORIF SET 300# RF SCH 40 BORE A105N, 1/2"-NPT TWO-TAPS, LSS, SPE 76/000,025, MW-004
5NPC204L362
398406
***** PIPE NIPPLES *****407408
11025XR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
4
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004)
M A T E R I A L
CS A106-B, LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
NIPPB3 0.5 - 1.5 NIPPLE SCH 80 A106-B, LSS, SPE 74/000,002,76/000, MW-004 PBE 3"-LONG
5MAC308L410
NIPPB6 0.5 - 1.5 NIPPLE SCH 80 A106-B, LSS, SPE 74/000,002,76/000, MW-004 PBE 6"-LONG
5MAC608L412
414NIPTB3 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004
TBE 3"-LONG5MBC318L420
NIPTB3 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TBE 3"-LONG
5MBC316L422
NIPTB6 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004 TBE 6"-LONG
5MBC618L424
NIPTB6 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TBE 6"-LONG
5MBC616L426
428NIPTO3 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004
TOE 3"-LONG5MCC318L430
NIPTO3 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TOE 3"-LONG
5MCC316L432
NIPTO6 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004 TOE 6"-LONG
5MCC618L434
NIPTO6 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TOE 6"-LONG
5MCC616L436
438440
***** SWAGE NIPPLES *****450452
SWACPE 0.5 - 1 SWAGE CONC SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 PBE
5MMC0808L460
SWACBE 0.5 - 1.5 SWAGE CONC SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MFC0808L462
SWACB1 0.5 - 1.5 SWAGE CONC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MFC0408L464
470SWAEPE 0.5 - 1 SWAGE ECC SCH 80 A234 WPB, LSS, SPE 76/000,003,
MW-004 PBE5MVC0808L480
SWAEBE 0.5 - 1.5 SWAGE ECC SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MPC0808L482
SWAEB1 0.5 - 1.5 SWAGE ECC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MPC0408L484
498499
***** GASKETS *****500501
GAS 0.5 - 6 GASKET 150# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR110510
GAS300 0.5 - 6907 GASKET 300# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR210512
548
11025XR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
5
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004)
M A T E R I A L
CS A106-B, LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
549***** BOLTING *****550
5511 BOL 50 - 1500 STUD-BOLT A193 GR B7M W/A194 GR 2HM NUTS,
FLOUROCARBON POLYMER COATED(TAKECOAT-1000 OR EQUAL),MW-004
5UBC001560
561562
***** SPECTACLE BLIND *****600602
SPEBLD 0.5 - 6 BLIND SPECTACLE 150# RF A516-65, LSS, SPE 76/000,012, MW-004
5NGC100L610
11025XR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
6
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004)
M A T E R I A L
CS A106-B, LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
PIPING BRANCH REINFORCENMENT REQUIREMENT
1/4
2 1/2
1 1/2
1/2
3/4
1
2
3
4
6
8
10
12
14
16
18
20
24
A
B
B
B
C
C
C
C
A
B
B
C
C
C
C
A
B
C
C
C
C
A
C
C
C
C
A
B
B
E
A
B
B
A
B A
H
A
D
E
R
S
I
Z
E
N
P
S
(IN)
242018 1614 1210 8 1/4 1/2 3/4 1 1 1/2 2 2 1/2 3 4 6
B R A N C H S I Z E ( N P S - I N C H )
E
1. ABBREVIATIONS. A : EQUAL TEE B : REDUCING TEE C : BRANCH FITTING PLAIN-END OUTLET E : BRANCH OUTLET REDUCING BUTT-WELD (WELDOLET)
11025XR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
REV.2
CLASS 11025XRE UNDERGROUND PIPING for 11025XR
BASIC MATERIAL CARBON STEEL, LSS ASME RATING CLASS 150 CORROSION ALLOWANCE 3 mm SERVICE P Lean Amine
P Lean Amine w/H2S(H2S
-
11025XRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
1
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004) 3) COAT & WRAP (5578-E1-SP-MY-001)
M A T E R I A L
CS A106-B (U/G), LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
17
***** VALVES *****89
B GAT 0.5 - 1.5 GATE 800# SW A105N TR-410 BB,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305
GA0115BGA011FA08P10
B GATSWS 0.5 - 1.5902 GATE 800# SW/SCRD A105N TR-410 BB,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305
GA0125CGA012FA08P11
B GATFLG 0.5 - 1.5901 GATE 150# RF A105N TR-410 BB,LSS,SPE 77/101,301,303,305
GA3115DGA311FA13
B GAT 2 - 6 GATE 150# RF A216-WCB TR-410 BB,LSS,SPE 77/102,301,303,305
GA3115DGA311A14
16B GLO 0.5 - 1.5 GLOBE 800# SW A105N TR-410 STEL
BB,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305GL0115BGL011FB08P21
B GLO 2 - 6105 GLOBE 150# RF A216-WCB TR-410 STEL BB,LSS,SPE 77/103,301,303,305
GL3115DGL311B23
24B CHE 0.5 - 1.5101 CHECK 800# SW A105N TR-410 BC
LIFT,W/NIP(100MM,S80)PWHT,LSS,SPE 77/101,301,303,305CH0115BCH011FA08P31
B CHE 2 - 4 CHECK 150# RF A216-WCB TR-410 BC SWING,LSS,SPE 77/104,301,303,305
CH3125DCH312A33
B CHE 6 - 6 CHECK 150# WAFER-LUG A216-WCB TR-410 DUAL PLT,LSS,SPE 77/133,301,303,305
CH3135DCH313A34
0033510039
B BAL 0.5 - 1.5 BALL 150# RF A105N,316-PTFE RED.BR FLOAT,LSS,SPE 77/100,301,303,305
BA3115DBA311FC41
B BAL 2 - 2 BALL 150# RF A216-WCB,316-PTFE RED.BR FLOAT,LSS,SPE 77/100,301,303,305
BA3115DBA311C42
B BAL 3 - 6 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION,LSS,SPE 77/100,301,303,305
BA3115DBA311CT43
B BALF 0.5 - 1.5412 BALL 150# RF A105N,316-PTFE FULL BR FLOAT,LSS,SPE 77/100,301,303,305
BA3125DBA312FC45
B BALF 2 - 2412 BALL 150# RF A216-WCB,316-PTFE FULL BR FLOAT,LSS,SPE 77/100,301,303,305
BA3125DBA312C46
B BALF 3 - 6412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION,LSS,SPE 77/100,301,303,305
BA3125DBA312CT47
9899
***** PIPE *****100101
PIP 0.5 - 1.5 PIPE SCH 80 SMLS A106-B PE, LSS, SPE 74/000,002, MW-004, 3LPE-COATED
5GCS080LU110
PIP 2 - 2 PIPE SCH 80 SMLS A106-B BE, LSS, SPE 74/000,002, MW-004, 3LPE-COATED
5GCS081LU111
PIP 3 - 6 PIPE SCH 40 SMLS A106-B BE, LSS, SPE 74/000,002, MW-004, 3LPE-COATED
5GCS041LU112
11025XRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
2
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004) 3) COAT & WRAP (5578-E1-SP-MY-001)
M A T E R I A L
CS A106-B (U/G), LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
148149
***** FITTINGS *****150151
ELL 0.5 - 1.5 ELL 90 DEG 3000# SW A105N, LSS, SPE 76/000, MW-0045JAC102L16045L 0.5 - 1.5 ELL 45 DEG 3000# SW A105N, LSS, SPE 76/000, MW-0045JBC102L161CAP 0.5 - 1.5 CAP 3000# SW A105N, LSS, SPE 76/000, MW-0045JDC102L162TEE 0.5 - 1.5 TEE 3000# SW A105N, LSS, SPE 76/000, MW-0045JCC102L163COU 0.5 - 1.5 COUPLING 3000# SW A105N, LSS, SPE 76/000, MW-0045JGC102L165PLG 0.5 - 1.5902 PLUG ROUND HEAD SCRD A105N, LSS, SPE 76/000, MW-0045JFC004L166
170BNIF 0.5 - 1.5 BRANCH FITTING FLANGED OUTLET 150# RF SCH 80 A105N
A=150MM, LSS, SPE 76/000,031, MW-0045LRC108L171
BNIP 0.5 - 1.5 BRANCH FITTING PLAIN END OUTLET 3000# SCH 80 A105N, LSS, SPE 76/000,031, MW-004
5LSC108L172
1 SOL 0.5 - 1.5903 SOCKOLET 3000# A105N, LSS, SPE 76/000, MW-0045LCC100L173TOL 0.5 - 0.5902 THREADOLET 6000# A105N, LSS, SPE 76/000, MW-0045LBC200L175TOL 0.75 - 1.5902 THREADOLET 3000# A105N, LSS, SPE 76/000, MW-0045LBC100L178
180ELL 2 - 2 ELL 90 DEG LR SCH 80 A234 WPB, LSS, SPE 76/000,003,
MW-0045KACS08L181
45L 2 - 2 ELL 45 DEG SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004
5KCCS08L182
CAP 2 - 2 CAP SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-0045KHCS08L183TEE 2 - 2 TEE SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-0045KDCS0808L184TEE1 2 - 2 TEE SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003,
MW-0045KDCS0408L186
REDCB1 2 - 2 REDUCER CONC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004
5KFCS0408L190
REDEB1 2 - 2 REDUCER ECC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004
5KGCS0408L192
WOL1 2 - 2 WELDOLET SCH 40 X SCH 80 A105N, LSS, SPE 76/000,030, MW-004
5LAC0408L194
195239
ELL 3 - 6 ELL 90 DEG LR SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-004
5KACS04L240
45L 3 - 6 ELL 45 DEG SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-004
5KCCS04L241
CAP 3 - 6 CAP SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-0045KHCS04L242TEE 3 - 6 TEE SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-0045KDCS0404L243REDCBW 3 - 4 REDUCER CONC SCH 40 A234 WPB, LSS, SPE 76/000,003,
MW-0045KFCS0404L247
11025XRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
3
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004) 3) COAT & WRAP (5578-E1-SP-MY-001)
M A T E R I A L
CS A106-B (U/G), LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
REDEBW 3 - 4 REDUCER ECC SCH 40 A234 WPB, LSS, SPE 76/000,003, MW-004
5KGCS0404L248
298299
***** FLANGES *****300301
FLG 0.5 - 1.5 FLG SW 150# RF SCH 80 BORE A105N, LSS, SPE 76/000,002, MW-004
5NQC108L302
FLG 2 - 2 FLG WN 150# RF SCH 80 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC108L303
FLG 3 - 6 FLG WN 150# RF SCH 40 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC104L304
305FLGJS 6 - 6 FLG WN 150# RF SCH 40 BORE A105N W/JACK SCREW, LSS,
SPE 76/000,002, MW-0045NMC104L310
319FLG300 0.5 - 1.5907 FLG SW 300# RF SCH 80 BORE A105N, LSS, SPE
76/000,002, MW-0045NQC208L320
FLG300 2 - 2907 FLG WN 300# RF SCH 80 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC208L321
FLG300 3 - 6907 FLG WN 300# RF SCH 40 BORE A105N, LSS, SPE 76/000,002, MW-004
5NNC204L322
329BLF 0.5 - 6 FLG BLIND 150# RF A105N, LSS, SPE 76/000,002, MW-0045NFC100L330BLF300 0.5 - 6907 FLG BLIND 300# RF A105N, LSS, SPE 76/000,002, MW-0045NFC200L332
339FLGLWN 1.5 - 1.5910 FLG LONG WN 300# RF A105N L=6", LSS, SPE 76/000,002,
MW-0045NYC200L340
348349
***** ORIFICE FLANGES *****350351
B ORI 2 - 2 WN ORIF SET 300# RF SCH 80 BORE A105N, 1/2"-NPT TWO-TAPS, LSS, SPE 76/000,025, MW-004
5NPC208L361
B ORI 3 - 6 WN ORIF SET 300# RF SCH 40 BORE A105N, 1/2"-NPT TWO-TAPS, LSS, SPE 76/000,025, MW-004
5NPC204L362
398406
***** PIPE NIPPLES *****407408
NIPPB3 0.5 - 1.5 NIPPLE SCH 80 A106-B, LSS, SPE 74/000,002,76/000, MW-004 PBE 3"-LONG
5MAC308L410
NIPPB6 0.5 - 1.5 NIPPLE SCH 80 A106-B, LSS, SPE 74/000,002,76/000, MW-004 PBE 6"-LONG
5MAC608L412
414
11025XRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
4
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004) 3) COAT & WRAP (5578-E1-SP-MY-001)
M A T E R I A L
CS A106-B (U/G), LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
NIPTB3 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004 TBE 3"-LONG
5MBC318L420
NIPTB3 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TBE 3"-LONG
5MBC316L422
NIPTB6 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004 TBE 6"-LONG
5MBC618L424
NIPTB6 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TBE 6"-LONG
5MBC616L426
428NIPTO3 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004
TOE 3"-LONG5MCC318L430
NIPTO3 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TOE 3"-LONG
5MCC316L432
NIPTO6 0.5 - 0.5 NIPPLE XXS A106-B, LSS, SPE 74/000,002,76/000, MW-004 TOE 6"-LONG
5MCC618L434
NIPTO6 0.75 - 1.5 NIPPLE SCH 160 A106-B, LSS, SPE 74/000,002,76/000, MW-004 TOE 6"-LONG
5MCC616L436
438440
***** SWAGE NIPPLES *****450452
SWACPE 0.5 - 1 SWAGE CONC SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 PBE
5MMC0808L460
SWACBE 0.5 - 1.5 SWAGE CONC SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MFC0808L462
SWACB1 0.5 - 1.5 SWAGE CONC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MFC0408L464
470SWAEPE 0.5 - 1 SWAGE ECC SCH 80 A234 WPB, LSS, SPE 76/000,003,
MW-004 PBE5MVC0808L480
SWAEBE 0.5 - 1.5 SWAGE ECC SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MPC0808L482
SWAEB1 0.5 - 1.5 SWAGE ECC SCH 40 X SCH 80 A234 WPB, LSS, SPE 76/000,003, MW-004 BLE/PSE
5MPC0408L484
498499
***** GASKETS *****500501
GAS 0.5 - 6 GASKET 150# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR110510
GAS300 0.5 - 6907 GASKET 300# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR210512
548549
***** BOLTING *****550551
11025XRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
5
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004) 3) COAT & WRAP (5578-E1-SP-MY-001)
M A T E R I A L
CS A106-B (U/G), LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
1 BOL 50 - 1500 STUD-BOLT A193 GR B7M W/A194 GR 2HM NUTS, FLOUROCARBON POLYMER COATED(TAKECOAT-1000 OR EQUAL),MW-004
5UBC001560
561562
***** SPECTACLE BLIND *****600602
SPEBLD 0.5 - 6 BLIND SPECTACLE 150# RF A516-65, LSS, SPE 76/000,012, MW-004
5NGC100L610
11025XRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11025XRE
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
6
5
1) SERVICE CODE: P, AD2) LSS (5578-E1-SP-MW-004) 3) COAT & WRAP (5578-E1-SP-MY-001)
M A T E R I A L
CS A106-B (U/G), LSS
STRESS RELIEF
PWHT ALL WELDS
RATING / FACING
-15 200
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS MAX.200HB REMARK
PIPING BRANCH REINFORCENMENT REQUIREMENT
1/4
2 1/2
1 1/2
1/2
3/4
1
2
3
4
6
8
10
12
14
16
18
20
24
A
B
B
B
C
C
C
C
A
B
B
C
C
C
C
A
B
C
C
C
C
A
C
C
C
C
A
B
B
E
A
B
B
A
B A
H
A
D
E
R
S
I
Z
E
N
P
S
(IN)
242018 1614 1210 8 1/4 1/2 3/4 1 1 1/2 2 2 1/2 3 4 6
B R A N C H S I Z E ( N P S - I N C H )
E
1. ABBREVIATIONS. A : EQUAL TEE B : REDUCING TEE C : BRANCH FITTING PLAIN-END OUTLET E : BRANCH OUTLET REDUCING BUTT-WELD (WELDOLET)
11025XRE
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
REV.2
CLASS 11045MR
BASIC MATERIAL CARBON STEEL ASME RATING CLASS 150 CORROSION ALLOWANCE 3 mm SERVICE PA Combustion Air NDE RT 10% PWHT - HARDNESS TEST 200HB
(Hardness testing is required where automatic or semiautomatic welding processes are used.) ADDITIONAL REQUIREMENTS - NOTES
NO DESCRIPTION
DESIGN LIMITS ARE ACC. FLANGE RATING ASME B16.5 MAT.GRP.1.1. 100 IN THE AVAILABLE SIZE RANGE BALL VALVES ARE PREFERRED TO GATE VALVES. 101 PISTON TYPE CHECK VALVES (1/2" - 1 1/2"), FOR HORIZONTAL MOUNTING ONLY. 105 IN LIEU OF GLOBE VALVES FOR SIZES NPS 8 & LARGER, GATE VALVES ARE PREFERRED TO BALL VALVES. USE OF SPECTACLE BLINDS, SPADE BLINDS AND SPACERS SHALL BE IN ACCORDANCE WITH 5578-E1-SP-PU-
016 (SPE 76/012). 300 BENDING OF PIPES SHALL ONLY BE DONE WHERE INDICATED IN THE PDS
ELECTRONIC FILE, OTHERWISE WELDING ELBOWS SHALL BE USED. THE USE OF BENDING WILL BE MINIMIZED AND SUBJECT TO COMPANY APPROVAL.
FOR BENDING OF PIPE SEE 5578-E1-SP-PU-002 412 USE ONLY WHEN A FULL-PORT OPENING IN A BALL VALVE IS REQUIRED. 001 VALVES SHALL BE IN ACCORDANCE WITH REFERENCED DATA SHEETS IN
VALVE MATERIAL SPECIFICATIONS 5578-E1-SP-PU-201 003 THE MAX. DESIGN TEMPERATURE FOR BALL VALVES SHALL BE LIMITED TO 175 DEG.C. 901 1 1/2" AND SMALLER FLANGED VALVES SHALL BE USED AGAINST FLANGED CONNECTIONS.
902 USE FOR DRAIN, VENT AND INSTRUMENT PIPING CONNECTIONS.
907 USE ONLY FOR EQUIPMENT CONNECTION OF HIGHER RATING.
910 USE LONG WELDING NECK FLANGES FOR TEMPERATURE CONNECTION OF PIPING 920 USE FOR INSULATED FLANGE BOLTING ABOVE 200 DEG.C 940 USE THIS CHECK VALVE WHERE DISSIMILAR TYPE IS SPECIFIED ON THE P&ID
-
11045MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
1
5
1) SERVICE CODE: PA*HARDNESS TEST FOR AUTO & SEMIAUTOMATIC WELDING ONLY
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 265
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS *MAX.200HB REMARK
15
***** VALVES *****68
B GAT 0.5 - 1.5 GATE 800# SW A105N TR-410 BB,SPE 77/101,301,302,304 GA2295BGA229FA11B GATSWS 0.5 - 1.5902 GATE 800# SW/SCRD A105N TR-410 BB,SPE
77/101,301,302,304GA2305CGA230FA12
B GATFLG 0.5 - 1.5901 GATE 150# RF A105N TR-410 BB,SPE 77/101,301,302,304 GA4635DGA463FA13B GAT 2 - 12 GATE 150# RF A216-WCB TR-410 BB,SPE
77/102,301,302,304GA4635DGA463A14
B GAT 14 - 24 GATE 150# RF A216-WCB TR-410 BB GO,SPE 77/102,301,302,304
GA4635DGA463AG15
16B GLO 0.5 - 1.5 GLOBE 800# SW A105N TR-410 STEL BB,SPE
77/101,301,302,304GL1625BGL162FB21
B GLO 2 - 6105 GLOBE 150# RF A216-WCB TR-410 STEL BB,SPE 77/103,301,302,304
GL4635DGL463B24
29B CHE 0.5 - 1.5101 CHECK 800# SW A105N TR-410 BC LIFT,SPE
77/101,301,302,304CH1505BCH150FA31
B CHE 2 - 4 CHECK 150# RF A216-WCB TR-410 BC SWING,SPE 77/104,301,302,304
CH7685DCH768A33
B CHE 6 - 24 CHECK 150# WAFER-LUG A216-WCB TR-410 DUAL PLT,SPE 77/133,301,302,304
CH7695DCH769A34
1 CHEDST 20 - 20940 CHECK 150# RF A216-WCB TR-410 BC PISTON,SPE 77/104,301,302,304
CH969K5DCH969A35
0033910040
B BAL 0.5 - 1.5 BALL 150# RF A105N,316-PTFE RED.BR FLOAT,SPE 77/100,301,302,304
BA4755DBA475FC42
B BAL 2 - 2 BALL 150# RF A216-WCB,316-PTFE RED.BR FLOAT,SPE 77/100,301,302,304
BA4755DBA475C43
B BAL 3 - 6 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION,SPE 77/100,301,302,304
BA4755DBA475CT45
B BAL 8 - 10 BALL 150# RF A216-WCB,316-PTFE RED.BR TRUNNION GO,SPE 77/100,301,302,304
BA4755DBA475CTG46
B BALF 0.5 - 1.5412 BALL 150# RF A105N,316-PTFE FULL BR FLOAT,SPE 77/100,301,302,304
BA4765DBA476FC47
B BALF 2 - 2412 BALL 150# RF A216-WCB,316-PTFE FULL BR FLOAT,SPE 77/100,301,302,304
BA4765DBA476C48
B BALF 3 - 6412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION,SPE 77/100,301,302,304
BA4765DBA476CT49
B BALF 8 - 10412 BALL 150# RF A216-WCB,316-PTFE FULL BR TRUNNION GO,SPE 77/100,301,302,304
BA4765DBA476CTG50
591 BTF 20 - 24 BUTTERFLY 150# WAFER LUG A216 WCB,DISC A351 CF8M,RTFE
SEAT,GO,W/BOLT&NUT,SPE 77/106,301,302,304BU551K5DBU551CG60
98
11045MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11045MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
2
5
1) SERVICE CODE: PA*HARDNESS TEST FOR AUTO & SEMIAUTOMATIC WELDING ONLY
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 265
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS *MAX.200HB REMARK
99***** PIPE *****100
101PIP 0.5 - 1.5 PIPE SCH 80 SMLS A106-B PE, SPE 74/000,0025GCS080102
1 PIP 2 - 6 PIPE SCH 40 SMLS A106-B BE, SPE 74/000,0025GCS041104PIP 8 - 24 PIPE SCH 20 SMLS A106-B BE, SPE 74/000,0025GCS021105
1 PIP 28 - 30 PIPE .375" WALL EFW A671-CC65 CL22(JF=1) BE, SPE 74/000,005
5GCW511106
110111
***** FITTINGS *****114115
ELL 0.5 - 1.5 ELL 90 DEG 3000# SW A105N, SPE 76/0005JAC10211645L 0.5 - 1.5 ELL 45 DEG 3000# SW A105N, SPE 76/0005JBC102117CAP 0.5 - 1.5 CAP 3000# SW A105N, SPE 76/0005JDC102118TEE 0.5 - 1.5 TEE 3000# SW A105N, SPE 76/0005JCC102119COU 0.5 - 1.5 COUPLING 3000# SW A105N, SPE 76/0005JGC102121PLG 0.5 - 1.5902 PLUG ROUND HEAD SCRD A105N, SPE 76/0005JFC004122
125BNIF 0.5 - 1.5 BRANCH FITTING FLANGED OUTLET 150# RF SCH 80 A105N
A=150MM, SPE 76/000,0315LRC108129
BNIP 0.5 - 1.5 BRANCH FITTING PLAIN END OUTLET 3000# SCH 80 A105N, SPE 76/000,031
5LSC108130
TOL 0.5 - 0.5902 THREADOLET 6000# A105N, SPE 76/0005LBC200131TOL 0.75 - 1.5902 THREADOLET 3000# A105N, SPE 76/0005LBC100132
1331 ELL 2 - 6 ELL 90 DEG LR SCH 40 A234 WPB, SPE 76/000,0035KACS041541 45L 2 - 6 ELL 45 DEG SCH 40 A234 WPB, SPE 76/000,0035KCCS041551 CAP 2 - 6 CAP SCH 40 A234 WPB, SPE 76/000,0035KHCS041561 TEE 2 - 6 TEE SCH 40 A234 WPB, SPE 76/000,0035KDCS0404157
TEE1 4 - 6 TEE SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KDCS02041581 REDCBW 2 - 4 REDUCER CONC SCH 40 A234 WPB, SPE 76/000,0035KFCS0404164
REDCB1 4 - 6 REDUCER CONC SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KFCS02041651 REDEBW 2 - 4 REDUCER ECC SCH 40 A234 WPB, SPE 76/000,0035KGCS0404166
REDEB1 4 - 6 REDUCER ECC SCH 20 X SCH 40 A234 WPB, SPE 76/000,0035KGCS02041671 WOL 2 - 2 WELDOLET SCH 40 X SCH 40 A105N, SPE 76/000,0305LAC04041681 WOL1 2 - 6 WELDOLET SCH 20 X SCH 40 A105N, SPE 76/000,0305LAC02041691 WOL2 2 - 6 WELDOLET .375" WALL X SCH 40 A105N, SPE 76/000,0305LAC5104170
11045MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11045MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
3
5
1) SERVICE CODE: PA*HARDNESS TEST FOR AUTO & SEMIAUTOMATIC WELDING ONLY
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 265
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS *MAX.200HB REMARK
174ELL 8 - 18 ELL 90 DEG LR SCH 20 A234 WPB, SPE 76/000,0035KACS0217945L 8 - 18 ELL 45 DEG SCH 20 A234 WPB, SPE 76/000,0035KCCS02180CAP 8 - 18 CAP SCH 20 A234 WPB, SPE 76/000,0035KHCS02181TEE 8 - 18 TEE SCH 20 A234 WPB, SPE 76/000,0035KDCS0202182TEE1 10 - 18 TEE SCH 20 A234 WPBW, SPE 76/000,0035KDCW0202183
1 TEE2 14 - 18 TEE .375" WALL X SCH 20 A234 WPBW, SPE 76/000,0035KDCW5102184REDCBW 8 - 16 REDUCER CONC SCH 20 A234 WPB, SPE 76/000,0035KFCS0202187REDCB1 12 - 18 REDUCER CONC SCH 20 A234 WPBW, SPE 76/000,0035KFCW0202188REDEBW 8 - 16 REDUCER ECC SCH 20 A234 WPB, SPE 76/000,0035KGCS0202189REDEB1 12 - 18 REDUCER ECC SCH 20 A234 WPBW, SPE 76/000,0035KGCW0202190WOL 8 - 10 WELDOLET SCH 20 X SCH 20 A105N, SPE 76/000,0305LAC0202191
1 WOL1 8 - 14 WELDOLET .375" WALL X SCH 20 A105N, SPE 76/000,0305LAC5102192197
ELL 20 - 24 ELL 90 DEG LR SCH 20 A234 WPBW, SPE 76/000,0035KACW0219845L 20 - 24 ELL 45 DEG SCH 20 A234 WPBW, SPE 76/000,0035KCCW02199CAP 20 - 24 CAP SCH 20 A234 WPB, SPE 76/000,0035KHCS02201TEE 20 - 24 TEE SCH 20 A234 WPBW, SPE 76/000,0035KDCW0202202
1 TEE1 20 - 24 TEE .375" WALL X SCH 20 A234 WPBW, SPE 76/000,0035KDCW5102203REDCBW 20 - 20 REDUCER CONC SCH 20 A234 WPBW, SPE 76/000,0035KFCW0202205
1 REDCB1 20 - 24 REDUCER CONC .375" WALL X SCH 20 A234 WPBW, SPE 76/000,003
5KFCW5102206
REDEBW 20 - 20 REDUCER ECC SCH 20 A234 WPBW, SPE 76/000,0035KGCW02022071 REDEB1 20 - 24 REDUCER ECC .375" WALL X SCH 20 A234 WPBW, SPE
76/000,0035KGCW5102208
2181 ELL 28 - 30 ELL 90 DEG LR .375" WALL A234 WPBW, SPE 76/000,0035KACW512201 45L 28 - 30 ELL 45 DEG .375" WALL A234 WPBW, SPE 76/000,0035KCCW512211 CAP 28 - 30 CAP .375" WALL A234 WPB, SPE 76/000,0035KHCS512221 TEE 28 - 30 TEE .375" WALL A234 WPBW, SPE 76/000,0035KDCW51512231 REDCBW 28 - 28 REDUCER CONC .375" WALL A234 WPBW, SPE 76/000,0035KFCW51512241 REDEBW 28 - 28 REDUCER ECC .375 WALL A234 WPBW, SPE 76/000,0035KGCW5151225
228299
***** FLANGES *****300301
FLG 0.5 - 1.5 FLG SW 150# RF SCH 80 BORE A105N, SPE 76/000,0025NQC108302
11045MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11045MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
4
5
1) SERVICE CODE: PA*HARDNESS TEST FOR AUTO & SEMIAUTOMATIC WELDING ONLY
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 265
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS *MAX.200HB REMARK
1 FLG 2 - 6 FLG WN 150# RF SCH 40 BORE A105N, SPE 76/000,0025NNC104304FLG 8 - 24 FLG WN 150# RF SCH 20 BORE A105N, SPE 76/000,0025NNC102305
1 FLG 28 - 30 FLG WN SER.A 150# RF .375" BORE A105N, SPE 76/000,0025NNCA51306309
FLGJS 6 - 6 FLG WN 150# RF SCH 40 BORE A105N W/JACK SCREW, SPE 76/000,002
5NMC104310
FLGJS 8 - 24 FLG WN 150# RF SCH 20 BORE A105N W/JACK SCREW, SPE 76/000,002
5NMC102311
1 FLGJS 28 - 30 FLG WN SER.A 150# RF .375" BORE A105N W/JACK SCREW, SPE 76/000,002
5NMCA51312
316FLG300 0.5 - 1.5907 FLG SW 300# RF SCH 80 BORE A105N, SPE 76/000,0025NQC208320
1 FLG300 2 - 6907 FLG WN 300# RF SCH 40 BORE A105N, SPE 76/000,0025NNC204322FLG300 8 - 24907 FLG WN 300# RF SCH 20 BORE A105N, SPE 76/000,0025NNC202323
327FLGJS3 6 - 6907 FLG WN 300# RF SCH 40 BORE A105N W/JACK SCREW, SPE
76/000,0025NMC204328
FLGJS3 8 - 24907 FLG WN 300# RF SCH 20 BORE A105N W/JACK SCREW, SPE 76/000,002
5NMC202329
340BLF 0.5 - 24 FLG BLIND 150# RF A105N, SPE 76/000,0025NFC100344
1 BLF 28 - 30 FLG BLIND SER.A 150# RF A105N, SPE 76/000,0025NFCA00345BLF300 0.5 - 24907 FLG BLIND 300# RF A105N, SPE 76/000,0025NFC200350
354FLGLWN 1.5 - 1.5910 FLG LONG WN 300# RF A105N L=6", SPE 76/000,0025NYC200356
358360
***** ORIFICE FLANGES *****370378
1 ORI 2 - 6 WN ORIF SET 300# RF SCH 40 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC204381
B ORI 8 - 14 WN ORIF SET 300# RF SCH 20 BORE A105N, 1/2"-NPT TWO-TAPS, SPE 76/000,025
5NPC202382
398399
***** PIPE NIPPLES *****400401
NIPPB3 0.5 - 1.5 NIPPLE SCH 80 A106-B, SPE 74/000,002,76/000 PBE 3"-LONG
5MAC308410
NIPPB6 0.5 - 1.5 NIPPLE SCH 80 A106-B, SPE 74/000,002,76/000 PBE 6"-LONG
5MAC608412
414
11045MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11045MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
5
5
1) SERVICE CODE: PA*HARDNESS TEST FOR AUTO & SEMIAUTOMATIC WELDING ONLY
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 265
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS *MAX.200HB REMARK
NIPTB3 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000 TBE 3"-LONG
5MBC318420
NIPTB3 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TBE 3"-LONG
5MBC316422
NIPTB6 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000 TBE 6"-LONG
5MBC618424
NIPTB6 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TBE 6"-LONG
5MBC616426
428NIPTO3 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000
TOE 3"-LONG5MCC318430
NIPTO3 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TOE 3"-LONG
5MCC316432
NIPTO6 0.5 - 0.5 NIPPLE XXS A106-B, SPE 74/000,002,76/000 TOE 6"-LONG
5MCC618434
NIPTO6 0.75 - 1.5 NIPPLE SCH 160 A106-B, SPE 74/000,002,76/000 TOE 6"-LONG
5MCC616436
448449
***** SWAGE NIPPLES *****450451
SWACPE 0.5 - 1 SWAGE CONC SCH 80 A234 WPB, SPE 76/000,003 PBE
5MMC0808460
1 SWACBE 0.5 - 1.5 SWAGE CONC SCH 40 X SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MFC0408464
466SWAEPE 0.5 - 1 SWAGE ECC SCH 80 A234 WPB, SPE 76/000,003
PBE5MVC0808480
1 SWAEBE 0.5 - 1.5 SWAGE ECC SCH 40 X SCH 80 A234 WPB, SPE 76/000,003 BLE/PSE
5MPC0408484
499500
***** GASKETS *****501502
GAS 0.5 - 24 GASKET 150# 316/316L SS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBR110510
1 GAS 28 - 30 GASKET SER.A 150# 316/316LSS SP/WND, GRAF. 316/316L-INNER/CS-CENTERING RING 1/8"T
5RBRA10511
519GAS300 0.5 - 24907 GASKET 300# 316/316L SS SP/WND, GRAF.
316/316L-INNER/CS-CENTERING RING 1/8"T5RBR210520
549***** BOLTING *****550
551BOL 50 - 1500 STUD-BOLT A193 GR B7 W/A194 GR 2H NUTS, FLOUROCARBON
POLYMER COATED(TAKECOAT-1000 OR EQUAL)5UBB001560
B BOL1 50 - 1500920 STUD-BOLT A193 GR B7 W/A194 GR 2H NUTS5UBB000562
11045MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11045MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
6
5
1) SERVICE CODE: PA*HARDNESS TEST FOR AUTO & SEMIAUTOMATIC WELDING ONLY
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 265
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS *MAX.200HB REMARK
564598
***** SPECTACLE BLIND *****600602
SPEBLD 0.5 - 12 BLIND SPECTACLE 150# RF A516-65, SPE 76/000,0125NGC100610619
BLDPAD 14 - 24 BLIND PADDLE 150# RF A516-65, SPE 76/000,0125NHC100620SPAPAD 14 - 24 SPACER PADDLE 150# RF A516-65, SPE 76/000,0125NJC100622
1 BLDPAD 28 - 30 BLIND PADDLE SER.A 150# RF A516-65, SPE 76/000,0125NHCA006231 SPAPAD 28 - 30 SPACER PADDLE SER.A 150# RF A516-65, SPE 76/000,0125NJCA00624
629SPEBL3 0.5 - 10907 BLIND SPECTACLE 300# RF A516-65, SPE 76/000,0125NGC200630
631BLDPA3 12 - 24907 BLIND PADDLE 300# RF A516-65, SPE 76/000,0125NHC200632SPAPA3 12 - 24907 SPACER PADDLE 300# RF A516-65, SPE 76/000,0125NJC200634
11045MR
CLASSREVISION STATUS
REV
ISSUE DATE
BY / CHK
2010-02-26A KSL SSM/ B
2010-05-18
KSL / SSM 02010-07-02
KSL / SSM 12011-05-27
KSL / JSY 22012-05-29
JUC / GNP / /
(MBSPER01B)
-
11045MR
09191D
SERVICE
PIPING MATERIAL SPECIFICATION PRIME :AS OF :
PAGE :
05/29/2012
7
5
1) SERVICE CODE: PA*HARDNESS TEST FOR AUTO & SEMIAUTOMATIC WELDING ONLY
M A T E R I A L
CS A106-B
STRESS RELIEF
NO
RATING / FACING
5 265
CONSTRUCTION
1-1/2" & SMALLER : SW 2" & LARGER : BW
CORR. ALLOW
3.0 MM
TEMPERATURE LIMIT CLASS
150 RFSFANSI / TO
(Specification Data)PROJECT :
CLIENT :
RRE Project
Abu Dhabi Oil Refining Company
Seq. Rev NOTE ITEMNAME ITEMCODE SIZE RANGE(NPS) D E S C R I P T I O N REFERENCE
NDE RT:10% HARDNESS *MAX.200HB REMARK
PIPING BRANCH REINFORCENMENT REQUIREMENT
1/4
2 1/2
1 1/2
1/2
3/4
1
2
3
4
6
8
10
12
14
16
18
20
24
THRU
A
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
A
B
B
C
C
C
C
C
C
C
C
C
C
C
C
A
B
C
C
C
C
C
C
C
C
C
C
C
C
A
C
C
C
C
C
C
C
C
C
C
C
C
A
B
B
E
E
E
E
E
E
E
E