arcat€¦ · web viewadhesion to concrete: 300 psi (2068 kpa) concrete cohesive failure per astm d...

SECTION 09 67 23RESINOUS FLOORING

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2017 - 2017 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Section includes:1.1.1.1 Commercial and decorative full broadcast color flake two coat resinous flooring.1.1.1.2 Commercial and industrial high build three coat polyaspartic full broadcast color

flake resinous flooring.1.1.1.3 Commercial and industrial high build two coat polyaspartic full broadcast reverse

color flake color system resinous flooring with optional clear topping third coat.1.1.1.4 Commercial and industrial high build polyaspartic silica sand broadcast system

resinous flooring with optional top coat.1.1.1.5 Commercial and industrial high build polyaspartic three-coat solid color resinous

flooring with optional top coat.1.1.1.6 Commercial and industrial two coat high build polyaspartic clear coat resinous

flooring.1.1.1.7 Industrial quartz full broadcast 1/8 inch four-coat high build polyaspartic resinous

flooring.1.1.1.8 Industrial quartz full broadcast three-coat high build polyaspartic resinous

flooring.1.1.1.9 Decorative and commercial metallic color three-coat high build polyaspartic

resinous flooring with optional clear top coat.1.1.1.10 Decorative and commercial high-build variegate color stain polyaspartic resinous

flooring system.1.1.1.11 Accessory products including self-leveling cementitious urethane cement slurry,

waterproofing membrane, reinforcing membrane, patching and fill material.

1.2 RELATED SECTIONS

1.2.1 Section 09 67 13.33 - Conductive Elastomeric Liquid Flooring.

1.2.2 Section 09 67 13 - Elastomeric Liquid Flooring.

1.3 REFERENCES

1.3.1 ASTM International (ASTM):1.3.1.1 ASTM C 811 - Standard Practice for Surface Preparation of Concrete for

Application of Chemical-Resistant Resin Monolithic Surfacings.1.3.1.2 ASTM D 412 - Test Methods for Vulcanized Rubber and Thermoplastic Rubbers

and Thermoplastic Elastomers-Tension.1.3.1.3 ASTM D 522 - Standard Test Methods for Mandrel Bend Test of Attached

Organic Coatings.

09 67 23-1

1.3.1.4 ASTM D 635 - Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position.

1.3.1.5 ASTM D 968 - Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive.

1.3.1.6 ASTM D 1308 - Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes

1.3.1.7 ASTM D 2047 - Standard Test Method for Static Coefficient of Friction of Polish-Coated Flooring Surfaces as Measured by the James Machine.

1.3.1.8 ASTM D 2240 - Standard Test Method for Rubber Property-Durometer Hardness.

1.3.1.9 ASTM D 2794 - Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact).

1.3.1.10 ASTM D 4060 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser.

1.3.1.11 ASTM D 4263 - Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method.

1.3.1.12 ASTM D 4541 - Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers.

1.3.1.13 ASTM F 1869 - Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride.

1.3.1.14 ASTM F 2170 - Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes.

1.3.2 FDA - U.S. Food and Drug Administration: Food processing environments.

1.3.3 USDA - United States Department of Agriculture: Food processing environments.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.4.2.1 Preparation instructions and recommendations.1.4.2.2 Storage and handling requirements and recommendations.1.4.2.3 Installation methods.

1.4.3 USGBC LEED Submittals: For flooring products, reports indicating compliance with requirements for low-emitting materials for Credits IEQ 4.2.

1.4.4 Installer Certificates: Signed by manufacturer certifying that installers comply with specified requirements.

1.4.5 Material Certificates: For each resinous flooring component, from manufacturer.

1.4.6 Material Test Reports: For each resinous flooring system, by a qualified testing agency.

1.4.7 Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

1.4.8 Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, color, and patterns.

1.4.9 Closeout Submittal: Maintenance data for resinous flooring to include in maintenance manuals.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.

09 67 23-2

1.5.2 Installer Qualifications: Minimum 2 year experience installing similar products.1.5.2.1 An authorized representative who is trained and approved by manufacturer.

1.5.3 Mockups: Verify selections made under sample submittals, demonstrate aesthetic effects, and set quality standards for materials and execution.1.5.3.1 Full-thickness mockups on 96 inches (2400 mm) square floor area selected by

Architect.1.5.3.1.1 Include 96 inches (2400 mm) length of integral cove base with inside and

outside corners.1.5.3.2 Subject to compliance with requirements, approved mockups may become part

of the completed Work if undisturbed at time of Substantial Completion.

1.6 PRE-INSTALLATION MEETINGS

1.6.1 Convene minimum two weeks prior to starting work of this section.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Deliver and store products in manufacturer's unopened packaging bearing the brand name and manufacturer's identification until ready for installation.

1.7.2 Handling: Handle materials to avoid damage.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.9 SEQUENCING

1.9.1 Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: FLEXMAR Coatings, Inc., which is located at: 3058 Leechburg Rd. Suite 8; Lower Burrell, PA 15068 ; Toll Free Tel: 877-339-1442; Tel: 724-339-1442; Fax: 724-339-1465 ; Email:request info ([email protected]); Web:www.flexmarpolyaspartics.com

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 COMMERCIAL AND DECORATIVE FULL BROADCAST COLOR FLAKE TWO COAT RESINOUS FLOORING

2.2.1 Basis of Design: Two Coat High-Build Polyaspartic Coating with Full Color Flake Broadcast as manufactured by FLEXMAR Coatings, Inc. Decorative color flake broadcast, resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.

2.2.2 Performance Requirements:2.2.2.1 VOC Content: 0 VOC's, virtually no odor.

09 67 23-3

2.2.2.2 USGBC LEED Credit Contribution: LEED V3 IEQ 4.2. Flooring products shall comply with the requirements of the California Department of Public Health's "Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers."

2.2.2.3 Flammability: Self-extinguishing according to ASTM D 635.2.2.2.4 Recoat: 1 to 2 hours between coats.2.2.2.5 Walk-On-Return-to-Service: 1 to 2 hours.

2.2.3 Standards Compliance:2.2.3.1 Federal Agency Approvals: USDA approved for food-processing environments.2.2.3.2 Federal Agency Approvals: FDA approved for food-processing environments.

2.2.4 System Characteristics:2.2.4.1 Color and Pattern: ______.2.2.4.2 Color and Pattern: As specified by Architect from manufacturer's range.2.2.4.3 Color and Pattern: Match Architect's sample.2.2.4.4 Wearing Surface: Matte.2.2.4.5 Wearing Surface: Gloss.2.2.4.6 Wearing Surface: Manufacturer's standard wearing surface.2.2.4.7 Overall System Thickness: 11 to 19 mils (0.28 to 0.48 mm) DFT.

2.2.5 Base Coating Product: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.2.5.1 Formulation Description: High solids.2.2.5.2 Type: Pigmented.2.2.5.3 Application Method: Roller, squeegee, or magic trowel.2.2.5.4 Number of Coats: One.2.2.5.5 Thickness of Coat: 4 to 7 mils (0.1 to 0.18 mm) DFT.2.2.5.6 Broadcast Aggregate: Color flakes into Self-Prime Colorcoat HS.

2.2.6 Top Coating Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.2.6.1 Formulation Description: High solids.2.2.6.2 Type: Clear.2.2.6.3 Application Method: Roller, squeegee, or magic trowel.2.2.6.4 Number of Coats: One.2.2.6.5 Thickness of Coats: 7 to 12 mils (0.18 to 0.3 mm) DFT.

2.2.7 Minimal Systems Property Requirements: When tested per test methods indicated:2.2.7.1 Adhesion to Concrete: 300 psi (2068 kPa) concrete cohesive failure per ASTM D

4541 Elcometer.2.2.7.2 Tensile Strength: 4,500 psi (31,026 kPa) per ASTM D 412.2.2.7.3 Falling Sand Abrasion Resistance: ASTM D 968.

2.2.7.3.1 Clear Coat: 32 quarts (30 liters) sand/dry mil.2.2.7.3.2 Color Coat: 40 quarts (38 liters) sand/dry mil.

2.2.7.4 Taber Abrasion: 0.34 to 0.43 grain (22 to 28 mg) weight loss per ASTM D 4060, CS 17 wheel, 35.3 oz (1,000 g) load, 1,000 rev.

2.2.7.5 Flexibility Mandrel Bend: No cracking or peeling, per ASTM D 522, 1/8 in (3.2 mm).

2.2.7.6 Impact: 160/160 in lbs Direct/Reverse, no cracking, per ASTM D 2794.2.2.7.7 Hardness: 77 Shore D per ASTM D 2240.2.2.7.8 Static Coefficient of Friction: Greater than 0.6 per ASTM D 2047.2.2.7.9 Chemical Resistance: Cured resinous flooring test specimens are unaffected

when tested per Manufacturer's chemical resistance chart per ASTM D 1308 spot testing.

2.2.7.9.1 Reagent: ______.

2.3 COMMERCIAL AND INDUSTRIAL HIGH BUILD THREE COAT POLYASPARTIC FULL

09 67 23-4

BROADCAST COLOR FLAKE RESINOUS FLOORING

2.3.1 Basis of Design: Three Coat High-Build Polyaspartic Coating with Full Color Flake Broadcast as manufactured by FLEXMAR Coatings, Inc. Decorative color flake broadcast, resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.

2.3.2 Performance Requirements:2.3.2.1 VOC Content: 0 VOC's, virtually no odor.2.3.2.2 USGBC LEED Credit Contribution: LEED V3 IEQ 4.2. Flooring products shall

comply with the requirements of the California Department of Public Health's "Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers."


2.3.3 System Characteristics:2.3.3.1 Color and Pattern: _____.2.3.3.2 Color and Pattern: As specified by Architect from manufacturer's full range.2.3.3.3 Color and Pattern: Match Architect's sample.2.3.3.4 Wearing Surface: Matte.2.3.3.5 Wearing Surface: Gloss.2.3.3.6 Overall System Thickness: 15 to 25 mils (0.38 to 0.63 mm) DFT.

2.3.4 Base Coating Product: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.3.4.1 Formulation Description: High solids.2.3.4.2 Type: Pigmented.2.3.4.3 Application Method: Roller, squeegee, or magic trowel.2.3.4.4 Number of Coats: One.2.3.4.5 Thickness of Coat: 4 to 7 mils (0.1 to 0.18 mm) DFT.2.3.4.6 Broadcast: Color flakes (full broadcast) into Self-Prime Colorcoat HS.

2.3.5 Top Coating Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.3.5.1 Formulation Description: High solids.2.3.5.2 Type: Clear.2.3.5.3 Number of Coats: Two.2.3.5.4 Thickness of Coats:

2.3.5.4.1 1st Clearcoat: 7 to 12 mils (0.18 to 0.3 mm) DFT.2.3.5.4.2 2nd Clearcoat: 4 to 6 mils (0.1 to 0.15 mm) DFT with anti-skid additives.

2.3.6 Minimal System Property Requirements: When tested per test methods indicated:2.3.6.1 Adhesion to Concrete: 300 psi (2068 kPa) concrete cohesive failure per ASTM D


2.3.6.3.1 Clear Coat: 32 quarts (30 liters) sand/dry mil.2.3.6.3.2 Color Coat: 40 quarts (38 liters) sand/dry mil.


2.3.6.5 Flexibility Mandrel Bend: No cracking or peeling, per ASTM D 522, 1/8 in (302 mm).


09 67 23-5


2.3.6.9.1 Reagent: ______.

2.4 COMMERCIAL AND INDUSTRIAL HIGH BUILD TWO COAT POLYASPARTIC FULL BROADCAST REVERSE COLOR FLAKE COLOR SYSTEM RESINOUS FLOORING WITH OPTIONAL CLEAR TOPPING THIRD COAT

2.4.1 Basis of Design: Two Coat High-Build Polyaspartic Coating with Reverse Color Flake Broadcast as manufactured by FLEXMAR Coatings, Inc. Color flake broadcast, resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.




2.4.3 System Characteristics:2.4.3.1 Color and Pattern: _____.2.4.3.2 Color and Pattern: As selected by Architect from manufacturer's full range.2.4.3.3 Color and Pattern: Match Architect's sample.2.4.3.4 Wearing Surface: Matte.2.4.3.5 Wearing Surface: Gloss.2.4.3.6 Overall System Thickness: 15 to 23 mils (0.38 to 0.58 mm) DFT.2.4.3.7 Overall System Thickness: 15 to 23 mils (0.38 to 0.58 mm) DFT with additional

clear surface topping.

2.4.4 Base Coat Products: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.4.4.1 Formulation Description: High solids.2.4.4.2 Type: Pigmented.2.4.4.3 Application Method: Roller, squeegee, or magic trowel.2.4.4.4 Number of Coats: Two.2.4.4.5 Thickness Coats:

2.4.4.5.1 First Coat: 4 to 7 mils (0.1 to 0.18 mm) DFT.2.4.4.5.2 Second Coat: 7 to 9 mils (0.1 to 0.18 mm) DFT.

2.4.4.6 Aggregate: Broadcast color flakes into the first coat.

2.4.5 Top Coating Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin Sealer with anti-skid additive.2.4.5.1 Formulation Description: High solids.2.4.5.2 Type: Clear.2.4.5.3 Application Method: Roller, squeegee, or magic trowel.2.4.5.4 Number of Coats: One2.4.5.5 Thickness: 4 to 7 mils (0.1 to 0.18 mm) DFT



09 67 23-6

2.4.6.3.1 Color Coat: 40 quarts (38 liters) sand/dry mil.2.4.6.3.2 Clear Coat: 32 quarts (30 liters) sand/dry mil.





2.4.6.9.1 Reagent: ______.

2.5 COMMERCIAL AND INDUSTRIAL HIGH BUILD POLYASPARTIC SILICA SAND BROADCAST SYSTEM RESINOUS FLOORING WITH OPTIONAL TOP COAT

2.5.1 Basis of Design: High Build Polyaspartic Coating with Silica Sand Broadcast as manufactured by FLEXMAR Coatings, Inc. Silica sand broadcast, resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.




2.5.3 System Characteristics:2.5.3.1 Color and Pattern: _____.2.5.3.2 Color and Pattern: As selected by Architect from manufacturer's full range.2.5.3.3 Color and Pattern: Match Architect's sample.2.5.3.4 Wearing Surface: Matte.2.5.3.5 Wearing Surface: Gloss.2.5.3.6 Overall System Thickness: 7 to 11 mils (0.18 to 0.28 mm) DFT.

2.5.4 Base Coating Product: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.5.4.1 Formulation Description: High solids.2.5.4.2 Type: Pigmented.2.5.4.3 Application Method: Roller, squeegee, or magic trowel.2.5.4.4 Number of Coats: One.2.5.4.5 Thickness of Coat: 4 to 7 mils (0.1 to 0.18 mm) DFT.2.5.4.6 Broadcast Aggregate: Silica sand into Self-Prime Colorcoat HS.

2.5.5 Top Coating Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.5.5.1 Formulation Description: High solids.2.5.5.2 Type Finish: Clear.2.5.5.3 Number of Coats: One.2.5.5.4 Thickness of Coat: 3 to 4 mils (0.1 to 0.18 mm) DFT.


09 67 23-7


2.5.6.3.1 Color Coat: 40 quarts (38 liters) sand/dry mil.2.5.6.3.2 Clear Coat: 32 quarts (30 liters) sand/dry mil.





2.5.6.9.1 Reagent: ______.

2.6 COMMERCIAL AND INDUSTRIAL HIGH BUILD POLYASPARTIC THREE COAT SOLID COLOR RESINOUS FLOORING WITH OPTIONAL TOP COAT.

2.6.1 Basis of Design: Three Coat High Build Solid Color System as manufactured by FLEXMAR Coatings, Inc. Polyaspartic resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.





2.6.4 Base Coating Product: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.6.4.1 Formulation Description: High solids.2.6.4.2 Type: Pigmented.2.6.4.3 Application Method: Roller, squeegee, or magic trowel.2.6.4.4 Number of Coats: Two.2.6.4.5 Thickness per Coat: 4 to 7 mils (0.1 to 0.18 mm) DFT.2.6.4.6 Aggregates: ______.2.6.4.7 Aggregates: As specified by Architect.

2.6.5 Top Coating Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin Sealer.2.6.5.1 Formulation Description: High solids.2.6.5.2 Type Finish: Clear.2.6.5.3 Number of Coats: One.2.6.5.4 Thickness of Coat: 3 to 4 mils (0.08 to 0.1 mm) DFT.

09 67 23-8



2.6.6.3.1 Clearcoat HS: 32 quarts (30 liters) sand/dry mil.2.6.6.3.2 Self-Prime Colorcoat HS: 40 quarts (38 liters) sand/dry mil.





2.6.6.9.1 Reagent: ______.

2.7 COMMERCIAL-INDUSTRIAL TWO COAT HIGH BUILD POLYASPARTIC CLEAR COAT RESINOUS FLOORING

2.7.1 Basis of Design: Two Coat Clear High Build Polyaspartic resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.




2.7.3 System Characteristics:2.7.3.1 Color and Pattern: _____.2.7.3.2 Color and Pattern: As selected by Architect from manufacturer's full range.2.7.3.3 Color and Pattern: Match Architect's sample.2.7.3.4 Wearing Surface: Gloss.2.7.3.5 Overall System Thickness: 8 to 12 mils (0.2 to 0.3 mm) DFT.

2.7.4 Base Coat Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.7.4.1 Formulation Description: High solids.2.7.4.2 Type: Clear.2.7.4.3 Application Method: Roller, squeegee, or magic trowel.2.7.4.4 Number of Coats: One.2.7.4.5 Thickness of Coat: 4 to 6 mils (0.1 to 0.15 mm) DFT.2.7.4.6 Finish: Gloss.

2.7.5 Topcoat:2.7.5.1 Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.7.5.2 Formulation Description: High solids.2.7.5.3 Type Finish: Clear.2.7.5.4 Number of Coats: One.2.7.5.5 Thickness of Coat: 4 to 6 mils (0.1 to 0.15 mm) DFT.

09 67 23-9



2.7.6.3.1 Clearcoat HS: 32 quarts (30 liters) sand/dry mil.2.7.6.4 Taber Abrasion: 0.34 to 0.43 grain (22 to 28 mg) weight loss per ASTM D 4060,

CS 17 wheel, 35.3 oz (1,000 g) load, 1,000 rev.2.7.6.5 Flexibility Mandrel Bend: No cracking or peeling, per ASTM D 522, 1/8 in (302

mm).2.7.6.6 Impact: 160/160 in lbs Direct/Reverse, no cracking, per ASTM D 2794.2.7.6.7 Hardness: 77 Shore D per ASTM D 2240.2.7.6.8 Static Coefficient of Friction: Greater than 0.6 per ASTM D 2047.2.7.6.9 Chemical Resistance: Cured resinous flooring test specimens are unaffected


2.7.6.9.1 Reagent: ______.

2.8 INDUSTRIAL QUARTZ FULL BROADCAST 1/8 INCH FOUR COAT HIGH BUILD POLYASPARTIC RESINOUS FLOORING

2.8.1 Basis of Design: Four Coat High Build Quartz Broadcast System as manufactured by FLEXMAR Coatings, Inc. Polyaspartic resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.





2.8.4 First Broadcast Coat Product: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.8.4.1 Formulation Description: High solids.2.8.4.2 Type: Pigmented.2.8.4.3 Application Method: Roller, squeegee, or magic trowel.2.8.4.4 Number of Coats: One.2.8.4.5 Thickness of Coat: 6 to 7 mils (0.15 to 0.17 mils) DFT.2.8.4.6 Broadcast: Quartz into Self-Prime Colorcoat HS.

2.8.5 Second Broadcast Coat Products: NextGen Clear Coat Polyaspartic Aliphatic Polyurea Resin.2.8.5.1 Formulation Description: High solids.2.8.5.2 Type: Clear.

09 67 23-10

2.8.5.3 Application Method: Roller, squeegee, or magic trowel.2.8.5.4 Number of Coats: One.2.8.5.5 Thickness of Coat: 8 to 10 mils (0.20 to 0.25 mils) DFT.2.8.5.6 Broadcast: Quartz into Clear Coat.

2.8.6 Top Coating Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.8.6.1 Formulation Description: High solids.2.8.6.2 Type Finish: Clear.2.8.6.3 Number of Coats: Two.2.8.6.4 Thickness of Coat:

2.8.6.4.1 1st Clearcoat: 11 to 13 mils (0.28 to 0.33 mils) DFT.2.8.6.4.2 2nd Clearcoat: 5 to 6 mils (0.12 to 0.15 mils) DFT.



2.8.7.3.1 Self-Prime Colorcoat HS: 40 quarts (38 liters) sand/dry mil.2.8.7.3.2 Clearcoat HS: 32 quarts (30 liters) sand/dry mil.



2.8.7.6 Impact: 160/160 in lbs Direct/Reverse, no cracking, per ASTM D 2794.2.8.7.7 Hardness: 77 Shore D per ASTM D 2240.2.8.7.8 Static Coefficient of Friction: Greater than 0.6 per ASTN D 2047.2.8.7.9 Chemical Resistance: Cured resinous flooring test specimens are unaffected


2.8.7.9.1 Reagent: ______.

2.9 INDUSTRIAL QUARTZ FULL BROADCAST THREE COAT HIGH BUILD POLYASPARTIC RESINOUS FLOORING

2.9.1 Basis of Design: Three Coat High Build Quartz Broadcast System as manufactured by FLEXMAR Coatings, Inc. Polyaspartic resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.





09 67 23-11

2.9.4 Base Coat Products: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyuria Resin.2.9.4.1 Formulation Description: High solids.2.9.4.2 Type: Pigmented.2.9.4.3 Application Method: Roller, squeegee, or magic trowel.2.9.4.4 Number of Coats: One.2.9.4.5 Thickness of Coat: 4 to 7 mils (0.1 to 0.18 mm) DFT.2.9.4.6 Broadcast: Quartz into Self-Prime Colorcoat HS.

2.9.5 Top Coating Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.9.5.1 Formulation Description: High solids.2.9.5.2 Type Finish: Clear.2.9.5.3 Number of Coats: Two.2.9.5.4 Thickness of Coat:

2.9.5.4.1 1st Clearcoat: 8 to 10 mils (0.2 to 0.25 mm) DFT.2.9.5.4.2 2nd Clearcoat: 8 to 10 mils (0.2 to 0.25 mm) DFT.

2.9.6 Minimal System Property Requirements: When tested per test methods indicated:2.9.6.1 Adhesion to Concrete: 300 psi (2068 kPa) concrete cohesive failure per ASTM

D 4541 Elcometer.2.9.6.2 Tensile Strength: 4,500 psi (31,026 kPa) per ASTM D 412.2.9.6.3 Falling Sand Abrasion Resistance: ASTM D 968.

2.9.6.3.1 Self-Prime Colorcoat HS: 40 quarts (38 liters) sand/dry mil.2.9.6.3.2 ClearCoat HS: 32 quarts (30 liters) sand/dry mil.



2.9.6.6 Impact: 160/160 in lbs Direct/Reverse, no cracking, per ASTM D 2794.2.9.6.7 Hardness: 77 Shore D per ASTM D 2240.2.9.6.8 Static Coefficient of Friction: Greater than 0.6 per ASTN D 2047.2.9.6.9 Chemical Resistance: Cured resinous flooring test specimens are unaffected


2.9.6.9.1 Reagent: ______.

2.10 DECORATIVE AND COMMERCIAL METALLIC COLOR THREE COAT HIGH BUILD POLYASPARTIC RESINOUS FLOORING WITH OPTIONAL CLEAR TOP COAT

2.10.1 Basis of Design: High-Build Metallic Color System with Optional Clear Coat as manufactured by FLEXMAR Coatings, Inc. Polyaspartic three coat metallic color system resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.




2.10.3 System Characteristics:2.10.3.1 Color and Pattern: _____.2.10.3.2 Color and Pattern: As selected by Architect from manufacturer's full range.

09 67 23-12

2.10.3.3 Color and Pattern: Match Architect's sample.2.10.3.4 Wearing Surface: Gloss.2.10.3.5 Overall System Thickness: 10 to 15 mils (0.25 to 0.38 mm) DFT; with optional

clear coat 13 to 19 mils (33 to 48 mm).

2.10.4 Base Coat Product: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.10.4.1 Formulation Description: High solids.2.10.4.2 Type: Pigmented.2.10.4.3 Application Method: Roller, squeegee, or magic trowel.2.10.4.4 Number of Coats: One.2.10.4.5 Thickness of Coat: 2 to 3 mils (0.05 to 0.08 mm) DFT.

2.10.5 Metallic Color Coat Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin with metallic pigment premix addition.2.10.5.1 Formulation Description: High Solids.2.10.5.2 Type: Metallic pigment added to NextGen "Clearcoat HS" as premix before

application.2.10.5.3 Number of Coats: One or Two, to achieve 8 to 12 mils (0.2 to 0.3 mm) DFT.2.10.5.4 Thickness of Coats:

2.10.5.4.1 One Coat: 8 to 12 mils (0.2 to 0.3 mm) DFT.2.10.5.4.2 Two Coats:

2.10.5.4.2.1 First Metallic Coat: 4 to 6 mils (0.1 to 0.15 mm) DFT.2.10.5.4.2.2 Second Metallic Coat: 4 to 6 mils (0.1 to 0.15 mm) DFT.

2.10.6 Clearcoat Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.10.6.1 Formulation Description: High solids.2.10.6.2 Type Finish: Clear.2.10.6.3 Number of Coats: One.2.10.6.4 Thickness of Coat: 3 to 4 mils (0.08 to 0.1 mm) DFT.

2.10.7 Minimal System Property Requirements: When tested per test methods indicated.2.10.7.1 Adhesion to Concrete: 300 psi (2068 kPa) concrete cohesive failure per ASTM D


2.10.7.3.1 Self-Prime Colorcoat HS: 40 quarts (38 liters) sand/dry mil.2.10.7.3.2 Clearcoat HS: 32 quarts (30 liters) sand/dry mil.





2.10.7.9.1 Reagent: ______.

2.11 DECORATIVE AND COMMERCIAL HIGH-BUILD VARIEGATE COLOR STAIN POLYASPARTIC RESINOUS FLOORING SYSTEM

2.11.1 Basis of Design: High-build variegate color stain polyaspartic resinous flooring system manufactured by FLEXMAR Coatings, Inc. Polyaspartic system resin-based monolithic floor surfacing designed to produce a seamless floor and integral cove base. Resistant to abrasions, impacts and chemicals.

09 67 23-13




2.11.3 System Characteristics:2.11.3.1 Color and Pattern: _____.2.11.3.2 Color and Pattern: As selected by Architect from manufacturer's full range.2.11.3.3 Color and Pattern: Match Architect's sample.2.11.3.4 Wearing Surface: Gloss.2.11.3.5 Overall System Thickness: 15 to 20 mils (0.38 to 0.508 mm) DFT.

2.11.4 Base Coat Product: NextGen Self-Prime Colorcoat HS Polyaspartic Aliphatic Polyurea Resin.2.11.4.1 Formulation Description: High solids.2.11.4.2 VOC Content: 0 VOC, virtually no odor.2.11.4.3 Type: Pigmented.2.11.4.4 Application Method: Roller, squeegee, or magic trowel.2.11.4.5 Number of Coats: One.2.11.4.6 Thickness of Coat: 3 to 5 mils (0.08 to 0.12 mm) DFT.

2.11.5 Variegate Color Stain Coat Product: NextGen Variegate Polyaspartic Aliphatic Polyurea Resin with factory mixed dyes and pigments.2.11.5.1 Formulation Description: High Solids.2.11.5.2 VOC Content: 0 VOC, virtually no odor.2.11.5.3 Type: Variegate stain sealer.2.11.5.4 Number of Variegate Stain Coats: One, to achieve 8 to 10 mils (0.20 to 0.25

mm) DFT.2.11.5.5 Number of Variegate Stain Coats: Two, to achieve 8 to 10 mils (0.20 to 0.25

mm) DFT total, with first coat at 4 to 5 mils (0.10 to 0.12 mm) DFT and second coat at 4 to 5 mils (0.10 to 0.12 mm) DFT.

2.11.6 Clearcoat Product: NextGen Clearcoat HS Polyaspartic Aliphatic Polyurea Resin.2.11.6.1 Formulation Description: High solids.2.11.6.2 Type: Clear.2.11.6.3 Finish: Gloss.2.11.6.4 Number of Coats: One.2.11.6.5 Thickness of Coat: 4 to 5 mils (0.10 to 0.12 mm) DFT.

2.11.7 Minimal System Property Requirements: When tested per test methods indicated.2.11.7.1 Adhesion to Concrete: 300 psi (2068 kPa) concrete cohesive failure per ASTM

D 4541 Elcometer.2.11.7.2 Tensile Strength: 4,500 psi (31,026 kPa) per ASTM D 412.2.11.7.3 Falling Sand Abrasion Resistance: ASTM D 968.

2.11.7.3.1 Clearcoat HS: 32 quarts (30 liters) sand/dry mil.2.11.7.4 Taber Abrasion: 0.34 to 0.43 grain (22 to 28 mg) weight loss per ASTM D 4060,

CS 17 wheel, 35.3 oz (1,000 g) load, 1,000 rev.2.11.7.5 Flexibility Mandrel Bend: No cracking or peeling, per ASTM D 522, 1/8 in (302

mm).2.11.7.6 Impact: 160/160 in lbs Direct/Reverse, no cracking, per ASTM D 2794.2.11.7.7 Hardness: 77 Shore D per ASTM D 2240.2.11.7.8 Flammability: Self-extinguishing per ASTM D 635.

09 67 23-14

2.11.7.9 Static Coefficient of Friction: Greater than 0.6 per ASTM D 2047.2.11.7.10 Chemical Resistance: Cured resinous flooring test specimens are unaffected


2.11.7.10.1 Reagent: ______.

2.12 ACCESSORY PRODUCTS

2.12.1 Waterproof Membranes: As recommended by resinous flooring manufacturer for flooring system and substrate specified.2.12.1.1 Waterproofing Membrane Formulation: 100 percent solids.2.12.1.2 Waterproofing Membrane Formulation: High solids.2.12.1.3 Primer: Self priming membrane.2.12.1.4 Primer: As recommending by resinous flooring manufacturer.

2.12.2 Reinforcing Membrane: As recommended by resinous flooring manufacturer for flooring system and substrate specified.2.12.2.1 Reinforcing Membrane Formulation: 100 percent solids.2.12.2.2 Reinforcing Membrane Formulation: High solids.

2.12.2.2.1 Provide fiberglass scrim embedded in reinforcing membrane.2.12.2.3 Primer: Self priming membrane.2.12.2.4 Primer: As recommending by resinous flooring manufacturer.

2.12.3 Patching and Fill Material: Resinous product of or approved by resinous flooring manufacturer and recommended by manufacturer for application indicated.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly prepared.

3.1.2 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

3.2.1 Prepare substrates per resinous flooring manufacturer's instructions.3.2.1.1 Concrete Substrates: Free of contaminants not compatible with resinous flooring.

3.2.1.1.1 Abrade surfaces as specified by system application guide.3.2.1.1.2 Comply with ASTM C 811 unless manufacturer's instructions instruct

otherwise.3.2.1.1.3 Damaged and deteriorated concrete is to be repaired per manufacturer's

instructions.3.2.1.1.4 Confirm moisture vapor emissions meet manufacturer's requirements.

3.2.1.1.4.1 Anhydrous Calcium Chloride Test: ASTM F 1869. Proceed after vapor-emission rate of slab is within acceptable parameters for 24 hours.

3.2.1.1.4.1.1 Vapor Emission Rate: 3 lbs of water per 1000 sq ft (1.36 kg of water per 92.9 sq m).

3.2.1.1.4.1.2 Vapor Emission Rate: 4.5 lbs of water per 1000 sq ft (2.04 kg of water per 92.9 sq m).

3.2.1.1.4.1.3 Vapor Emission Rate: ______.3.2.1.1.4.1.4 Vapor Emission Rate: As specified by Architect.

3.2.1.1.4.2 Plastic Sheet Test: ASTM D 4263. Proceed after testing indicates absence of moisture.

3.2.1.1.4.3 Relative Humidity Test: ASTM F 2170. Proceed after testing

09 67 23-15

indicates a 75 percent relative humidity level measurement, or lower.

3.2.1.2 Alkalinity and Adhesion Testing: Verify pH of substrate is within acceptable range.

3.2.1.3 Perform manufacturer recommended tests.3.2.1.4 Proceed after substrates pass testing.

3.2.2 Patching and Filling: Fill holes and depressions in substrates per manufacturer's instructions.3.2.2.1 Slope floor to drains and adjoining perimeter flooring.3.2.2.2 Treat control joints and substrate cracks to prevent cracks from propagating

through resinous flooring per manufacturer's instructions.

3.3 APPLICATION

3.3.1 Resinous Materials: Mix components and prepare materials per resinous flooring manufacturer's instructions.

3.3.2 Apply components of resinous flooring system per manufacturer's instructions to produce a uniform, monolithic wearing surface of thickness indicated.3.3.2.1 Coordinate application of components to provide optimum adhesion of resinous

flooring system to substrate, and optimum intercoat adhesion.

3.4 PROTECTION

3.4.1 Protect installed products until completion of project.

3.4.2 Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

09 67 23-16

arcat€¦ · web viewadhesion to concrete: 300 psi (2068 kpa) concrete cohesive failure per astm d...

Documents