ASSEMBLY INSTRUCTIONS

SLIDING DOOR

Decide which hand is required. Right hand opening illustrated.

Change the hand by turning the door upside down.

V01/01/2013

BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION

1) General Information

2) Additional Notes

Please inspect this product upon delivery. any missing parts or manufacturing

defects must be reported immediately to the supplier. Damage of defects reported

later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS-AVOID

HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.

Glass breakage claims will not be accepted after the product has been unpacked.

Please note--alumimium is a soft metal, and undergoes a series of extrusion.

fabrication, polishing and anodising processes in order to create your finished

shower enclosure. Some light surface marks are normal, and is a result of the

manufacturing processes. Quality control has ensured that this item is of a good

standard, and is fit for purpose.

Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.

Note: this product is heavy and may require two people to install.

TOOLS REQUIRED

This product is heavy and may require two people to install.

Ø3mm Drill bit

Ø6mm Drill bit

Pencil

Spirit level

Tape measure

DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE

Drill

Flat-headScrewdriver

Cross headScrewdriver

Hammer

Silicone Sealant

1

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)(11)

(13)

(12)

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(1)6xWall Plugs (8)1xUpright Magnet Profile (15)1xPlastic Water Deflectors

(2)2xWall Profiles (9)1xMagnet Seal A (16)1xHandle

(3)1xSide Panel (10)1xMagnet Seal B (17)1xMoving Panel

(4)1xCorner Post Profile (11)1xBottom Profile (18)1xFixed Panel

(5)18xScrew Cover Clips (12)2xGlass Clips (19)2xTop Double Rollers

(6)6xScrew 4x30 (13)2xBottom Double Rollers (20)1xTop Profile

(7)18xScrew Cover Caps (14)1xPlastic Water Deflector (21)8xScrews 3.5x30

(22)2xScrews 4x10

ASSEMBLY INSTRUCTIONS-DRAWING+SIDE PANEL

2

Sid

e p

an

el

Door

ASSEMBLY INSTRUCTIONS

If you require help, we advise you firstly contact a competent plumber

MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS SHOWER

PANEL / DOOR.

Installation Steps

M4X10

M4X10

M3.5X30

M3.5X30

M3.5X30

M3.5X30

Step 1

Step 2

3

Step 3

Step 4

4

Step 5

Step 6

5

Step 7

Step 8

6

How to adjust the width of the

sliding door

Minimum 10mm internal overlap required

Glass panel

Glass panel

Vertical profile

Vertical profile

Wall profile

Wall profile

Wall

Wall

Maximum adjustment

Minimum adjustment

x6

x6

x6

Step 9

Step 10

7

Step 1

Step 2

8

Sid

e p

an

el

Door

Do not install the corner post upside down.

Step 3

Step 4

9

How to adjust the width of the

side panel

Minimum 10mm internal overlap required

Glass panel

Glass panel

Vertical profile

Vertical profile

Wall profile

Wall profile

Wall

Wall

Maximum adjustment

Minimum adjustment

CARE AND MAINTENANCE

COMMITMENT TO QUALITY

1) AFTER CARE INSTRUCTIONS

2) MAINTENANCE

Regularly clean your shower product with warm soapy water

Clean the plastic parts with a cloth and mild detergent. Never

use any abrasive creams, dissolvents, acetone or detergents

and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained

in these instructions. The supplier reserves the right to introduce

technical changes without notice.

It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you

firstly contact a competent plumber. However we understand that

this may not always be the case, so should you experience

any problems please contact out customer services quoting

the following:

Product name: 6mm Sliding Shower Door

Product code: SSD1002 SSD1102 SSD1202 SSD1602

Customer help line number:0844 804 45 45

to prevent lime scale build up. Do not use abrasive cleaning

fluids or materials, or strong chemical cleaners as this will

damage the product surface.

10