assembly xls columns for sct supports.pdf

7/26/2019 Assembly XLS Columns for SCT Supports.pdf

1/184

1

Assembly XLS Columns for

SCT Supports


2/184

2

Contents ................................................................................................................ 5

() ............................................................................................................. 6

................................................................................................................................................... 7

............................................................................................................. 17

() .................................................................................................... 18

................................................................................................................................................. 19

......................................................................................... 32

() ............................................................................................... 33

................................................................................................................................................. 35

.................................................................................................. 46

() ......................................................................................... 47

................................................................................................................................................. 47

............................................................................................................ 50

() .................................................................................................... 51

................................................................................................................................................. 51

, , & ......................................................... 54

() ........................................................................................ 55

................................................................................................................................................. 56

......................................................................................................... 62

() ................................................................................................. 63

................................................................................................................................................. 63

..................................................................................................................... 67

() ............................................................................................................ 68

................................................................................................................................................. 68 ................................................................................ 71

()..................................................................................................... 72

................................................................................................................................................. 73

........................................................................................................................ 78

.................................................................................. 79

()........................................................................................... 80

................................................................................................................................................. 81

........................................................................................................................ 86

............................................................................. 87

() ...................................................................................... 88 ................................................................................................................................................. 89

........................................................................................................................ 95

....................................................................................... 96

() .................................................................................................. 97

................................................................................................................................................. 97

...................................................................................................................... 100


3/184

3

...................................................................................... 101

() ...................................................................................... 102

............................................................................................................................................... 102

...................................................................................................................... 106

................................................................................. 107

() ................................................................................. 108

............................................................................................................................................... 108

...................................................................................................................... 113

.................................................................................................. 114

() ....................................................................................................... 115

............................................................................................................................................... 116

.................................................................................................... 122

() .................................................................................. 123

............................................................................................................................................... 124

............................................................................................... 129

() .............................................................................. 130

............................................................................................................................................... 131

...................................................................................................................... 134

............................................................................... 135

() .................................................................................................. 136

............................................................................................................................................... 137

...................................................................................................................... 142

..................................................................... 143

() ........................................................................................ 144

............................................................................................................................................... 145

...................................................................................................................... 151

............................................................................ 152

() ................................................................................... 153

............................................................................................................................................... 154

...................................................................................................................... 160

() .................................................................................................. 161

................................................................................................................................................... 162

() ............................................................................................... 166

................................................................................................................................................... 167

() .......................................................................................... 168

................................................................................................................................................... 168

() .......................................................................................... 170

................................................................................................................................................... 170

() ...................................................................................... 173

................................................................................................................................................... 173

() ......................................................................................... 176

................................................................................................................................................... 177


4/184

4

() ......................................................................................... 180

................................................................................................................................................... 181

.................................................................................................................................. 184


5/184

5


6/184

6

()

Common Attributes Horizontal Beam End Plate A End Plate B

IJUAhsC

atalog::Catalog

IJUAHgr

URSCommon::Type

IJUAHgr

URSCommon::Family

IJUAHgr

URSCommon::PSDetail

IJUAHgr

URS_

AuxBeam::AuxBeamSectionSize

IJUAHgr

URS_

AuxBeam::AuxBeamMaterial

IJUAHgr

URS_

AuxBeam::AuxBeamFaceSe

lection

IJUAHgr

URS_

AuxBeam::AuxBeamOrientation

IJUAHgr

URS_

AuxBeam::AuxBeamMirror

IJUAHgr

URS_

Channel::BackToBack

IJUAHgr

URS_

EndPlateA::EndPlateAPart

IJUAHgr

URS_

EndPlateA::EndPlateAThickness

IJUAHgr

URS_

EndPlateA::EndPlateAWidth

IJUAHgr

URS_

EndPlateA::EndPlateALength

IJUAHgr

URS_

EndPlateA::EndPlateAMaterial

IJUAHgr

URS_

EndPlateB::EndPlateBPart

IJUAHgr

URS_

EndPlateB::EndPlateBThickness

IJUAHgr

URS_

EndPlateB::EndPlateBWidth

IJUAHgr

URS_

EndPlateB::EndPlateBLength

IJUAHgr

URS_

EndPlateB::EndPlateBMaterial

Anchor Bolt A Anchor Bolt B Clip A Clip Bolt A

IJ

UAHgrURS_

AnchorBoltA::BoltAPa

rt

IJ

UAHgrURS_

AnchorBoltA::BoltAQu

antity

IJ

UAHgrURS_

AnchorBoltA::BoltAEm

bedmentDepth

IJ

UAHgrURS_

AnchorBoltA::BoltAH1

IJ

UAHgrURS_


IJ

UAHgrURS_

AnchorBoltA::BoltAMat

IJ

UAHgrURS_

AnchorBoltB::BoltBPa

rt

IJ

UAHgrURS_

AnchorBoltB::BoltBQu

antity

IJ

UAHgrURS_

AnchorBoltB::BoltBEm

bedmentDepth

IJ

UAHgrURS_

AnchorBoltB::BoltBH1

IJ

UAHgrURS_


IJ

UAHgrURS_

AnchorBoltB::BoltBMat

IJ

UAHgrURS_

Clip::ClipSectionSize

IJ

UAHgrURS_

Clip::ClipQuantity

IJ

UAHgrURS_

Clip::ClipMaterial

IJ

UAHgrURS_

Clip::ClipLength

IJ

UAHgrURS_

ClipBolt::BoltPart

IJ

UAHgrURS_

ClipBolt::BoltOffset

IJ

UAHgrURS_

ClipBolt::BoltMaterial


7/184

7

Clip B Clip Bolt B Dimensions

IJUA

HgrURS_

ClipB::ClipBSectionSize

IJUA

HgrURS_

ClipB::ClipBQuantity

IJUA

HgrURS_

ClipB::ClipBMaterial

IJUA

HgrURS_

ClipB::ClipBLength

IJUA

HgrURS_

ClipBoltB::ClipBoltBPart

IJUA

HgrURS_

ClipBoltB::ClipBoltBOffset

IJUA

HgrURS_

ClipBoltB::ClipBoltBMate

rial

IJUA

HgrURS_

ClipOffset::ClipOffset

IJUA

HgrURS_

ClipBOffset::ClipBOffset

IJUA

HgrURS_

BBGap::BBGap

IJUA

HgrURSBeamOffset::BeamOffset

IJUA

HgrURS_

MaxSpan::MaxSpan

IJUA

HgrURS_

MinSpan::MinSpan

Common Attributes refers to Common Attributtes.

Attribute Name Description Image

IJUAHgrURS_AuxBeam

::AuxBeamSectionSize

Type:String

Default:[empty]

Purpose:Enter the

Section Size of the beam.

IJUAHgrURS_AuxBeam::AuxBeamMaterial

Type:Long - CodelistDefault:1Purpose:Enter the codelist value of Beam Material.


8/184

8

Codelist:WGMaterialOfConstruction

IJUAHgrURS_AuxBeam

::AuxBeamFaceSelection

Type:Long - CodelistDefault:1

Purpose:Enter the codelist value for Beam FaceSelection.

Codelist:URSAttatchment

1 - Web2 - Flange3 - Lap

IJUAHgrURS_AuxBeam::AuxBeamOrientation

Type:Long - CodelistDefault:1Purpose:Enter the codelist value for BeamOrientation.

Codelist:URSSteelOrientation

1 - 0 Degrees2 - 90 Degrees3 - 180 Degrees4 - 270 Degrees

IJUAHgrURS_AuxBeam::AuxBeamMirror


Purpose:Enter the codelist value for Mirror option.


1 - Standard2 - Mirrored


9/184

9

IJUAHgrURS_Channel::BackToBack

Type:Long - CodelistDefault:NoPurpose:Enter the codelist value for BackToBackoption.

Codelist:URSYesNo

1 - Yes2 - No

IJUAHgrURS_EndPlateA::EndPlateAPart

Type:String

Default:[empty]

Purpose:Enter the partnumber or class for theEnd Plate A.

EndPlate part is not used in this assembly.

IJUAHgrURS_EndPlateA::EndPlateAThickness

Type:Double - Distance

Default:0

Purpose:Enter the

thickness of the End Plate

A.

IJUAHgrURS_EndPlateA::EndPlateAWidth


Default:0

Purpose:Enter the Width

of the End Plate A.

IJUAHgrURS_EndPlateA::EndPlateALength


Default:0

Purpose:Enter the Length

of the End Plate A.


10/184

10

IJUAHgrURS_EndPlateA::EndPlateAMaterial

Type:Long - CodelistDefault:[empty]Purpose:Enter the codelist value of End Plate AMaterial.


IJUAHgrURS_EndPlateB::EndPlateBPart

Type:String

Default:[empty]

Purpose:Enter the partnumber or class for theEnd Plate B.

End Plate part is not used in this assembly.

IJUAHgrURS_EndPlateB::EndPlateBThickness


Default:0

Purpose:Enter thethickness of the End PlateB.

IJUAHgrURS_EndPlateB::EndPlateBWidth


Default:0

Purpose:Enter the Width

of the End Plate B.

IJUAHgrURS_EndPlateB::EndPlateBLength


Default:0

Purpose:Enter the Length

of the End Plate B.

IJUAHgrURS_EndPlateB::EndPlateBMaterial

Type:Long - CodelistDefault:[empty]Purpose:Enter the codelist value of End Plate AMaterial.


IJUAHgrURS_AnchorBoltA::BoltAPart

Type:String

Default:[empty]

Purpose:Enter the partnumber or class for theAnchor Bolt A Part.

Anchor Bolt Part is not used in this assembly.

IJUAHgrURS_AnchorBoltA Type:Long


11/184

11

::BoltAQuantity Default:[empty]Purpose:Enter thequantity of Anchor Bolt A.

IJUAHgrURS_AnchorBoltA

::BoltAEmbedmentDepth


Default:0

Purpose:Enter the

Embedment Depth of

Anchor Bolt A.

IJUAHgrURS_AnchorBoltA::BoltAH1


Default:0

Purpose:Enter the H1value of Anchor Bolt A.

IJUAHgrURS_AnchorBoltA

::BoltAH2


Default:0

Purpose:Enter the H2value of Anchor Bolt A.

IJUAHgrURS_AnchorBoltA::BoltAMat

Type:Long - CodelistDefault:[empty]Purpose:Enter the codelist value of Anchor Bolt AMaterial.


IJUAHgrURS_AnchorBoltB::BoltBPart Type:String

Default:[empty]

Purpose:Enter the partnumber or class name forthe Anchor Bolt B Part.

Anchor Bolt Part is not used in this assembly.

IJUAHgrURS_AnchorBoltB::BoltBQuantity

Type:LongDefault:[empty]Purpose:Enter thequantity of Anchor Bolt Brequired.

IJUAHgrURS_AnchorBoltB

::BoltBEmbedmentDepth


Default:0

Purpose:Enter the

Embedment Depth of

Anchor Bolt B.

IJUAHgrURS_AnchorBoltB::BoltBH1



12/184

12

Default:0

Purpose:Enter the H1value of Anchor Bolt B.



Default:0

Purpose:Enter the H2value of Anchor Bolt B.

IJUAHgrURS_AnchorBoltB::BoltBMat

Type:Long - CodelistDefault:[empty]Purpose:Enter the codelist value of Anchor Bolt BMaterial.


IJUAHgrURS_Clip::ClipSectionSize

Type:String

Default:[empty]

Purpose:Enter theSection Size of Clip A.

IJUAHgrURS_Clip

::ClipQuantity

Type:Long

Default:[empty]Purpose:Enter thequantity of Clip A required.

IJUAHgrURS_Clip::ClipMaterial

Type:Long - CodelistDefault:[empty]Purpose:Enter the codelist value of Clip A Material.


13/184

13


IJUAHgrURS_Clip::ClipLength


Default:0

Purpose:Enter the Lengthof Clip A.

IJUAHgrURS_ClipBolt::BoltPart

Type:String

Default:[empty]

Purpose:Enter the partnumber or class of ClipBolt A.

IJUAHgrURS_ClipBolt::BoltOffset


Default:0

Purpose:Enter the valuefor Clip Bolt A Offset.

IJUAHgrURS_ClipBolt::BoltMaterial

Type:Long - CodelistDefault:[empty]Purpose:Enter the codelist value of Clip Bolt AMaterial.



14/184

14

IJUAHgrURS_ClipB::ClipBSectionSize

Type:String

Default:[empty]

Purpose:Enter theSection Size of Clip B.

IJUAHgrURS_ClipB::ClipBQuantity

Type:LongDefault:[empty]Purpose:Enter thequantity of Clip B required.

IJUAHgrURS_ClipB::ClipBMaterial

Type:Long - CodelistDefault:[empty]Purpose:Enter the codelist value of Clip B Material.


IJUAHgrURS_ClipB::ClipBLength


Default:0

Purpose:Enter the Lengthof Clip B.

IJUAHgrURS_ClipBoltB::ClipBoltBPart

Type:String

Default:[empty]

Purpose:Enter the part

number or class of ClipBolt B.

IJUAHgrURS_ClipBoltB::ClipBoltBOffset


Default:0

Purpose:Enter the valuefor Clip Bolt B Offset.

IJUAHgrURS_ClipBoltB Type:Long - Codelist


15/184

15

::ClipBoltBMaterial Default:1Purpose:Enter the codelist value of Clip Bolt BMaterial.

Codelist:

WGMaterialOfConstructionIJUAHgrURS_ClipOffset::ClipOffset


Default:0

Purpose:Enter the valuefor Clip A Offset.

IJUAHgrURS_ClipBOffset::ClipBOffset


Default:0

Purpose:Enter the valuefor Clip B Offset.

IJUAHgrURS_BBGap::BBGap


Default:0

Purpose:Enter the valuefor Back to Back Gap.


16/184

16

IJUAHgrURSBeamOffset::BeamOffset


Default:0

Purpose:Enter the valuefor Beam Offset.

IJUAHgrURS_MaxSpan::MaxSpan


Default:0

Purpose:Enter theMaximum Span value.

IJUAHgrURS_MinSpan::MinSpan


Default:0

Purpose:Enter theMinimum Span value.


17/184

17


18/184

18

()

Common Attributes Beam A Beam B Beam

IJUAhsC

atalog::Catalog

IJUAHgr

URSCommon::Type

IJUAHgr

URSCommon::Family

IJUAHgr

URSCommon::PSDetail

IJUAHgr

URS_

BoxFrBeamA::BeamASectionSize

IJUAHgr

URS_

BoxFrBeamA::BeamAMaterial

IJUAHgr

URS_

BoxFrBeamA::BeamAOrientation

IJUAHgr

URS_

BoxFrBeamA::BeamAMirror

IJUAHgr

URS_

NucEndCap::NucEndCap

IJUAHgr

URS_

BoxFrBeamB::BeamBSectionSize

IJUAHgr

URS_

BoxFrBeamB::BeamBMaterial

IJUAHgr

URS_

BoxFrBeamB::BeamBOrientation

IJUAHgr

URS_

BoxFrBeamB::BeamBMirror

IJUAHgr

URS_

NucEndCapB::NucEndCapB

IJUAHgr

URS_

BoxFrBeam::BeamSectionSize

IJUAHgr

URS_

BoxFrBeam::BeamMaterial

IJUAHgr

URS_

BoxFrBeam::BeamOrientatio

n

IJUAHgr

URS_

BoxFrBeam::BeamMirror

IJUAHgr

URS_

BoxFrBeam::BeamConnectionA

IJUAHgr

URS_

BoxFrBeam::BeamConnectionB

End Plate A End Plate B End Plates Anchor Bolt A

IJ

UAHgrURS_

EndPlateA::EndPlateAPart

IJ

UAHgrURS_

EndPlateA::EndPlateAThickness

IJ

UAHgrURS_

EndPlateA::EndPlateAWidth

IJ

UAHgrURS_

EndPlateA::EndPlateALength

IJ

UAHgrURS_

EndPlateA::EndPlateAMaterial

IJ

UAHgrURS_

EndPlateB::EndPlateBPart

IJ

UAHgrURS_

EndPlateB::EndPlateBThickness

IJ

UAHgrURS_

EndPlateB::EndPlateBWidth

IJ

UAHgrURS_

EndPlateB::EndPlateBLength

IJ

UAHgrURS_

EndPlateB::EndPlateBMaterial

IJ

UAHgrURS_

HEndPlate::HEndPlat

esParts

IJ

UAHgrURS_

HEndPlate::HEndPlat

esMaterial

IJ

UAHgrURS_

AnchorBoltA::BoltAPa

rt

IJ

UAHgrURS_

AnchorBoltA::BoltAQu

antity

IJ

UAHgrURS_

AnchorBoltA::BoltAEm

bedmentDepth

IJ

UAHgrURS_


IJ

UAHgrURS_


IJ

UAHgrURS_

AnchorBoltA::BoltAMat


19/184

19

Anchor Bolt B Pipe Attachment Dimensions

IJUA

HgrURS_

AnchorBoltB::BoltBPart

IJUA

HgrURS_

AnchorBoltB::BoltBQuan

tity

IJUA

HgrURS_

AnchorBoltB::BoltBEmbe

dmentDepth

IJUA

HgrURS_


IJUA

HgrURS_


IJUA

HgrURS_

AnchorBoltB::BoltBMat

IJUA

HgrURS_

PipeAttach::PipeAttachm

ent

IJUA

HgrURS_

PipeAttach::PipeAttQuan

tity

IJUA

HgrURS_

PipeAttach::PipeAttMaterial

IJUA

HgrURS_

PipeAttach::PipeAttLength

IJUA

HgrURS_

PipeAttCap::PipeAttCap

IJUA

HgrURS_

Oh1::Ohv

IJUA

HgrURS_

Oh2::Ohh

IJUA

HgrURS_

BoxFrameGap::G1

IJUA

HgrURS_

BoxFrameGap::G2

IJUA

HgrURS_

BoxFrameGap::G3

IJUA

HgrURS_

BoxFrameGap::G4



IJUAHgrURS_BoxFrBeamA::BeamASectionSize

Type:StringDefault:[Empty]Purpose:Enter the

Section Size to be used forBeam A.

IJUAHgrURS_BoxFrBeamA::BeamAMaterial

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Beam AMaterial.



20/184

20

IJUAHgrURS_BoxFrBeamA::BeamAOrientation

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Beam AOrientation.


IJUAHgrURS_BoxFrBeamA::BeamAMirror

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Beam AMirror.

Codelist:URSSteelMirror


21/184

21

IJUAHgrURS_NucEndCap::NucEndCap

Type:CharDefault:[empty]Purpose:Enter the platepart used for the caps ofthe nuclear frame.

IJUAHgrURS_BoxFrBeamB::BeamBSectionSize

Type:StringDefault:[Empty]Purpose:Enter theSection Size to be used forBeam B.

IJUAHgrURS_BoxFrBeamB::BeamBMaterial

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Beam BMaterial.

Codelist:

WGMaterialOfConstruction


22/184

22

IJUAHgrURS_BoxFrBeamB::BeamBOrientation

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Beam BOrientation.


IJUAHgrURS_BoxFrBeamB::BeamBMirror

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Beam BMirror.



23/184

23

IJUAHgrURS_NucEndCapB::NucEndCapB

Type:CharDefault:[empty]Purpose:Enter the platepart used for the caps ofthe nuclear frame.

IJUAHgrURS_BoxFrBeam::BeamSectionSize

Type:StringDefault:[empty]Purpose:Enter theSection Size to be used forthis support.

IJUAHgrURS_BoxFrBeam::BeamMaterial

Type:Long - CodelistDefault:[Empty]Purpose:Enter the code

list value of BeamMaterial.



24/184

24

IJUAHgrURS_BoxFrBeam::BeamOrientation

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of BeamOrientation.


IJUAHgrURS_BoxFrBeam::BeamMirror

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Beam Mirror.



25/184

25

IJUAHgrURS_BoxFrBeam::BeamConnectionA

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value for connectingBeam to Beam A.

Codelist:URSSteelConnection

IJUAHgrURS_BoxFrBeam::BeamConnectionB

Type:Long - CodelistDefault:[Empty]Purpose:Enter the code

list value for connectingBeam to Beam B.

Codelist:URSSteelConnection

IJUAHgrURS_EndPlateA::EndPlateAPart

Type:CharDefault:[Empty]Purpose:Enter plate partname for End Plate A.

IJUAHgrURS_EndPlateA::EndPlateAThickness

Type:DoubleDefault:[Empty]Purpose:Enter End PlateA thickness.

IJUAHgrURS_EndPlateA Type:Double


26/184

26

::EndPlateAWidth Default:[Empty]Purpose:Enter End PlateA width.

IJUAHgrURS_EndPlateA::EndPlateALength

Type:DoubleDefault:[Empty]

Purpose:Enter End PlateA length.

IJUAHgrURS_EndPlateA::EndPlateAMaterial

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of End Plate AMaterial.


IJUAHgrURS_EndPlateB::EndPlateBPart

Type:CharDefault:[Empty]Purpose:Enter plate partname for End Plate B.

IJUAHgrURS_EndPlateB::EndPlateBThickness

Type:DoubleDefault:[Empty]Purpose:Enter End Plate

B thickness.

IJUAHgrURS_EndPlateB::EndPlateBWidth

Type:DoubleDefault:[Empty]Purpose:Enter End PlateB width.

IJUAHgrURS_EndPlateB::EndPlateBLength

Type:DoubleDefault:[Empty]Purpose:Enter End PlateB length.

IJUAHgrURS_EndPlateB::EndPlateBMaterial

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of End Plate BMaterial.


IJUAHgrURS_HEndPlate::HEndPlatesParts

Type:CharDefault:[Empty]


27/184

27

Purpose:Enter plate partname for Horizontal EndPlates

IJUAHgrURS_HEndPlate::HEndPlatesMaterial

Type:Long - CodelistDefault:[Empty]

Purpose:Enter the codelist value of Horizontal EndPlate Material


IJUAHgrURS_AnchorBoltA::BoltAPart

Type:CharDefault:[Empty]Purpose:Enter part namefor Anchor Bolts on EndPlate A

IJUAHgrURS_AnchorBoltA::BoltAQuantity

Type:LongDefault:[Empty]Purpose:Enter thenumber of Anchor Bolts tobe present on plate A

[1,2,4]

IJUAHgrURS_AnchorBoltA::BoltAEmbedmentDepth

Type:DoubleDefault:[Empty]Purpose:Enter the depththat Anchor Bolts A are tobe embedded into EndPlate A measured frominside face of bolt to faceof plate opposite ofstructure attachment


28/184

28


Type:DoubleDefault:[Empty]Purpose:Enter thehorizontal offset of AnchorBolts A from left and rightsides of End Plate A.


Type:DoubleDefault:[Empty]Purpose:Enter thevertical offset of AnchorBolts A from top and

bottom sides of End PlateA.

IJUAHgrURS_AnchorBoltA::BoltAMat

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of Anchor Bolt AMaterial


IJUAHgrURS_AnchorBoltB::BoltBPart

Type:CharDefault:[Empty]Purpose:Enter part namefor Anchor Bolts on EndPlate B

IJUAHgrURS_AnchorBoltB::BoltBQuantity

Type:LongDefault:[Empty]


29/184

29

Purpose:Enter thenumber of Anchor Bolts tobe present on plate B

[1,2,4]

IJUAHgrURS_AnchorBoltB::BoltBEmbedmentDepth Type:DoubleDefault:[Empty]Purpose:Enter the depththat Anchor Bolts B are tobe embedded into EndPlate B measured frominside face of bolt to faceof plate opposite ofstructure attachment


Type:DoubleDefault:[Empty]Purpose:Enter thehorizontal offset of AnchorBolts B from left and rightsides of End Plate B


Type:DoubleDefault:[Empty]Purpose:Enter thevertical offset of AnchorBolts B from top andbottom sides of End PlateB

IJUAHgrURS_AnchorBoltB::BoltBMat

Type:Long - CodelistDefault:[Empty]


30/184

30

Purpose:Enter the codelist value of Anchor Bolt BMaterial


IJUAHgrURS_PipeAttach::PipeAttachment

Type:CharDefault:[Empty]Purpose:Enter partnumber for PipeAttachment

IJUAHgrURS_PipeAttach

::PipeAttQuantity

Type:Long

Default:[Empty]Purpose:Enter thenumber of PipeAttachments

IJUAHgrURS_PipeAttach::PipeAttMaterial

Type:Long - CodelistDefault:[Empty]Purpose:Enter the codelist value of PipeAttachment Material


IJUAHgrURS_PipeAttach::PipeAttLength

Type:DoubleDefault:[Empty]Purpose:Enter the lengthof Pipe Attachments

IJUAHgrURS_PipeAttCap::PipeAttCap

Type:CharDefault:[Empty]Purpose:Enter the partname for the PipeAttachment Cap

IJUAHgrURS_Oh1::Ohv


31/184

31

IJUAHgrURS_Oh2::Ohh

Type:DoubleDefault:[empty]Purpose:Enter thedistance from the end ofthe support to the closestedge of the cross member

IJUAHgrURS_BoxFrameGap::G1

Type:DoubleDefault:[empty]Purpose:Enter thedistance between theoutside of pipe and theinside of right crossmember


Type:DoubleDefault:[empty]Purpose:Enter thedistance between theoutside of pipe and theinside of top crossmember


Type:DoubleDefault:[empty]Purpose:Enter thedistance between theoutside of pipe and theinside of left cross member


Type:DoubleDefault:[empty]

Purpose:Enter thedistance between theoutside of pipe and theinside of bottom crossmember


32/184

32


33/184

33

()

Steel Leg 1

Common Attributes Part Start Overhang End Overhang Cap Plate

IJUAhsSupportN

umber::SupportNumber

IJUAhsSteelStandard::SteelStandard

IJUAhsFrameTy

pe::FrameType

IJUAhsFrameCo

nfiguration::FrameConfiguration

IJUAhsFrameOrientation::FrameOrientation

IJUAhsMirrorFra

me::MirrorFrame

IJUAhsIncludeIn

sulation::IncludeInsulation

IJUAhsLeg1::Leg1Part

IJUAhsLeg1::Leg1Rule

IJUAhsLeg1::Leg1OrientationAngle

IJUAhsLeg1Ove

rlength::Leg1BeginOverhangValue

IJUAhsLeg1Ove

rlength::Leg1BeginOverhangRule

IJUAhsLeg1Ove

rlength::Leg1BeginOverhangDefin

ition

IJUAhsLeg1Ove

rlength::Leg1BeginOverhangSelec

tion

IJUAhsLeg1Ove

rlength::Leg1EndOverhangValue

IJUAhsLeg1Ove

rlength::Leg1EndOverhangRule

IJUAhsLeg1Ove

rlength::Leg1EndOverhangDefinition

IJUAhsLeg1Ove

rlength::Leg1EndOverhangSelection

IJUAhsCapPlate

1::CapPlate1Part

IJUAhsCapPlate

1::CapPlate1Rule

IJUAhsCapPlate

1::CapPlate1Angle

Steel Leg 1Steel

Connections

Common Attributes Part

Start

Overhang

End

Overhang Cap Plate Leg 1

IJUAhsSupportNumber

::SupportNumber


IJUAhsFrameType::Fra

meType

IJUAhsFrameConfigura

tion::FrameConfiguration

IJUAhsFrameOrientatio

n::FrameOrientation

IJUAhsMirrorFrame::MirrorFrame

IJUAhsIncludeInsulation::IncludeInsulation




IJUAhsLeg1Overlength

::Leg1BeginOverhangValue


::Leg1BeginOverhangRule


::Leg1BeginOverhangDefinition


::Leg1BeginOverhangSelection


::Leg1EndOverhangValue


::Leg1EndOverhangRule


::Leg1EndOverhangDefinition


::Leg1EndOverhangSelection

IJUAhsCapPlate1::Cap

Plate1Part


Plate1Rule


Plate1Angle

IJUAhsCornerConnection1::Connection1Type

IJUAhsCornerConnection1::Connection1Swap

IJUAhsCornerConnection1::Connection1Mirror


34/184

34

Main Steel Member

Part Start Overhang End OverhangStart Cap

PlateEnd Cap

Plate

IJUAhsMember1::Member1Part

IJUAhsMember1::Member1Rule

IJUAhsMember1::Member1OrientationAngle

IJUAhsMember1Overlength::Member1BeginOverhangValue

IJUAhsMember1Overlength::Member1BeginOverhangRule

IJUAhsMember1Overlength::Member1BeginOverhangDefinition

IJUAhsMember1Overlength::Member1BeginOverhangSelection

IJUAhsMember1Overlength::Member1EndOverhangValue

IJUAhsMember1Overlength::Member1EndOverhangRule

IJUAhsMember1Overlength::Member1EndOverhangDefinition

IJUAhsMember1Overlength::Member1EndOverhangSelection

IJUAhsCapPlate2::CapPlate

2Part


2Rule


2Angle


3Part


3Rule


3Angle

Structure Connection 1 Input DimensionsOutput

Dimensions

Base Plate1

AnchorBolt 1 Offset 1 Offset 2 Shoe Height Span

Length 1

IJUAhsBasePlate1::BasePlate1Part

IJUAhsBasePlate1::BasePlate1Rule

IJUAhsBasePlate1::BasePlate1Angle

IJUAhsBolt1::Bolt1Part

IJUAhsBolt1::Bolt1Rule

IJUAhsBolt1::Bolt1Quan

tity

IJUAhsFrameOffset1::Offset1Value

IJUAhsFrameOffset1::Offset1Rule

IJUAhsFrameOffset1::Offset1Definition

IJUAhsFrameOffset1::Offset1Selection





IJUAhsFrameShoeHeight::ShoeHeightValue

IJUAhsFrameShoeHeight::ShoeHeightRule

IJUAhsFrameShoeHeight::ShoeHeightDefinition

IJUAhsFrameShoeHeight::ShoeHeightSelection

IJUAhsFrameSpan::Spa

nValue

IJUAhsFrameSpan::Spa

nDefinition

IJUAhsFrameLength1::L

ength1Value

IJUAhsFrameLength1::L

ength1Definition


35/184

35


IJUAhsSupportNumber::SupportNumber

Type:StringDefault:[Empty]Purpose:Enter the SupportDetail Number of the support.

This value will be used bythe default BOM functionwhen generating the BOMDescription for the support.


Type:Long - CodelistDefault:[Empty]Purpose:Enter theInternational Steel Standardto be used by the support. Ifexternal rules were written topick the steel section, this

attribute would be used todetermine the standard touse.

Codelist:hsSteelStandard

1 - Undefined5 - EURO-OTUA-2002

10 - AISC-LRFD-3.1

IJUAhsFrameType::FrameType

Type:Long - CodelistDefault:[Empty]Purpose:Enter the FrameType to be used for thesupport.

This attribute would be usedby rules that may need toknow what type of frame thesupport is.

Codelist:hsFrameType

1 - U Shaped Frame2 - L Shaped Frame3 - T Shaped Frame

4 - Split T Shaped Frame5 - I Shaped Frame6 - Cantilever Frame

IJUAhsFrameConfiguration::FrameConfiguration

Type:Long - CodelistDefault:[1]Purpose:

This property will move the


36/184

36

main steel section to theopposite side of the pipe.

Codelist:hsFrameConfiguration

1 - Configuration 12 - Configuration 2IJUAhsFrameOrientation

::FrameOrientationType:Long - CodelistDefault:[1]Purpose: Enter the codelistvalue to Specify how theframe support should beoriented with respect to thesupporting object or theglobal coordinate system.

When Direct Orientation isused on a curved supportingobject, such as equipment,

the Frame orientation will beradial to the primarysupported object.

Codelist:hsFrameOrientation

1 - Direct2 - Orthogonal3 - Tangent

IJUAhsMirrorFrame::MirrorFrame

Type:BitDefault:[0]

Purpose:Specify whether the frame

support should mirror aboutthe bounding box or not.

IJUAhsIncludeInsulation::IncludeInsulation

Type:BitDefault:[1]Purpose: Specify whetherthe Frame should adjust itssize to include pipe insulationor not.

If there are no insulated

pipes, then this will have noeffect.


Type:StringDefault:[Empty]Purpose:

Enter the Steel Part-Numberto use for the first leg of thesupport.


37/184

37

If Part-Number is selectedusing Leg1Rule, then thisattribute should be left blank.


Type:StringDefault:[Empty]Purpose:

Enter the name of a Rule,or a rule ProgID to select theLeg1 Part.


Type:Long - CodelistDefault:[Empty]Purpose:

Enter the codelist value toSpecify the angle of rotationfor the first leg of the support.The angle is about the legsaxis.

Use this attribute to specifythe orientation of the steelpart in the support. Thiswould differ depending on thesection type and the type ofconnection between the steelparts.

Codelist:hsSteelOrientationAngle

0 - 0 Degrees90 - 90 Degrees

180 - 180 Degrees

270 - 270 Degrees

IJUAhsLeg1Overlength::Leg1BeginOverhangValue

Type:Double - DistanceDefault:[Empty]Purpose: Enter the distancethat the first leg shouldoverhang past the mainmember.

If you intend to useLeg1BeginOverhangRule todetermine the value of theoverhang, then this attribute

should be left blank.IJUAhsLeg1Overlength

::Leg1BeginOverhangRuleType:StringDefault:[Empty]Purpose: Enter the name ofa Rule, or a rule ProgID toselect the Leg1 BeginOverhang.

IJUAhsLeg1Overlength::Leg1BeginOverhangDefinition

Type:LongDefault:[Empty]Purpose: Specify how the


38/184

38

Begin Overhang should bemeasured.

IJUAhsLeg1Overlength::Leg1BeginOverhangSelection

Type:Long - CodelistDefault:[By Input]Purpose: Enter the code list

value to specify whether theoverhang be specified byinput or by rule.

Codelist:hsSelection

1 - By Rule2 - By Input

IJUAhsLeg1Overlength::Leg1EndOverhangValue

Type:Double - DistanceDefault:[Empty]Purpose: Enter the distancethat the first leg shouldoverhang past the supportingobject.

If you intend to useLeg1EndOverhangRule todetermine the value of theoverhang, then this attributeshould be left blank.

IJUAhsLeg1Overlength::Leg1EndOverhangRule

Type:StringDefault:[Empty]Purpose: Enter the name ofa Rule, or a rule ProgID toselect the Leg1 End

Overhang.IJUAhsLeg1Overlength

::Leg1EndOverhangDefinitionType:LongDefault:[Empty]Purpose: Specify how theEnd Overhang should bemeasured.

IJUAhsLeg1Overlength::Leg1EndOverhangSelection

Type:Long - CodelistDefault:[By Input]Purpose: Enter the code listvalue to specify whether theEnd Overhang be specifiedby input or by rule.



IJUAhsCapPlate1::CapPlate1Part

Type:StringDefault: [Empty]Purpose: Enter the Part-

CapPlate1 part is not used in thisassembly.


39/184

39

Number or Part-Class of theplate placed on the end of thefirst leg. This must be aSmart-Part 2 Port Plate.

IJUAhsCapPlate1::CapPlate1Rule

Type:StringDefault:[Empty]

Purpose: Enter the name ofa Rule, or a rule ProgID toselect the CapPlate1 Part.

IJUAhsCapPlate1::CapPlate1Angle

Type:Double - AngleDefault:[Empty]Purpose: Enter the anglethat CapPlate1 should berotated about the z-axis ofthe port that the plate isattached to (either BeginFaceor EndFace).

IJUAhsCornerConnection1::Connection1Type

Type:Long - CodelistDefault:[Empty]Purpose: Enter the type ofconnection to use whenconnecting Leg1 toMember1.

Codelist:hsSteelCornerConnection

0 - Butted1 - Lapped2 - Nested3 - Coped4 - Fitted5 - Mitered

IJUAhsCornerConnection1::Connection1Swap

Type:BitDefault: [Empty]Purpose: Specify whetherthe connection between Leg1 and Member1 should beswapped or not, so they areconnected in the reversedorder.

IJUAhsCornerConnection1::Connection1Mirror

Type: BitDefault: [Empty]Purpose: Specify whetherthe connection between Leg

1 and Member 1 should bemirrored or not.

IJUAhsMember1::Member1Part

Type:StringDefault:[Empty]Purpose: Enter the SteelPart-Number to use for thefirst member of the support.


40/184

40

If Part-Number is selectedusing Member1Rule, thenthis attribute should be leftblank.

IJUAhsMember1::Member1Rule


Purpose: Enter the name ofa Rule, or a rule ProgID to

select the Leg1 Part.

IJUAhsMember1::Member1OrientationAngle

Type:Long - CodelistDefault:[1]Purpose: Enter the codelistvalue to Specify the angle ofrotation for the main member.The angle is about themembers axis.

Use this attribute to specifythe orientation of the steelpart in the support. Thiswould differ depending on thesection type and the type ofconnection between the steelparts.

Codelist:hsSteelOrientationAngle



IJUAhsMember1Overlength::Member1BeginOverhangValue

Type:Double - DistanceDefault:[Empty]Purpose: Enter the distancethat the main member shouldoverhang past the first leg.

If you intend to useMember1BeginOverhangRuleto determine the value of theoverhang, then this attributeshould be left blank.

IJUAhsMember1Overlength::Member1BeginOverhangRule

Type:StringDefault:[Empty]Purpose: Enter the name ofa Rule, or a rule ProgID toselect the Member1 BeginOverhang.

IJUAhsMember1Overlength

::Member1BeginOverhangDefinition

Type:LongDefault:[Empty]Purpose: Specify how the


41/184

41

Begin Overhang should bemeasured.


::Member1BeginOverhangSelection

Type:Long - CodelistDefault:[By Input]Purpose: Enter the code list

value to specify whether theoverhang be specified byinput or by rule.



IJUAhsMember1Overlength::Member1EndOverhangValue

Type:Double - DistanceDefault:[Empty]Purpose: Enter the distancethat the main section shouldoverhang past the secondleg.If you intend to useLeg1EndOverhangRule todetermine the value of theoverhang, then this attributeshould be left blank.

IJUAhsMember1Overlength::Member1EndOverhangRule

Type:StringDefault:[Empty]Purpose: Enter the name ofa Rule, or a rule ProgID toselect the Member1 EndOverhang.


::Member1EndOverhangDefinition

Type:LongDefault:[Empty]Purpose: Specify how theEnd Overhang should bemeasured.


::Member1EndOverhangSelection

Type:Long - CodelistDefault:[By Input]Purpose: Enter the code listvalue to specify whether theEnd Overhang be specifiedby input or by rule.




Type:StringDefault:[Empty]Purpose: Enter the Cap

CapPlate2 is not used in thisassembly.


42/184

42

Plate part number to use.

If part number is selectedusing CapPlate2Rule, thenthis attribute should be leftblank.

IJUAhsCapPlate2::CapPlate2Rule Type:StringDefault:[Empty]Purpose: Enter the name of

a Rule, or a rule ProgID to

select the CapPlate2 Part.


Type:Double - AngleDefault:[Empty]Purpose: Enter the angle of

Cap Plate 2.


Type:StringDefault:[Empty]Purpose: Enter the CapPlate part number to use.

If part number is selectedusing CapPlate3Rule, thenthis attribute should be leftblank.

IJUAhsCapPlate3::CapPlate3Rule

Type:StringDefault:[Empty]Purpose: Enter the name of


select the CapPlate3 Part.



Cap Plate 3.

IJUAhsBasePlate1::BasePlate1Part

Type:StringDefault:[Empty]Purpose: Enter the BasePlate part number to use.

If part number is selectedusing BasePlate1Rule, thenthis attribute should be leftblank.

IJUAhsBasePlate1::BasePlate1Rule




43/184

43

select the BasePlate1 Part.

IJUAhsBasePlate1::BasePlate1Angle


BasePlate1.

IJUAhsBolt1::Bolt1Part

Type:StringDefault:[Empty]Purpose: Enter the Bolt partnumber to use.

If part number is selectedusing Bolt1Rule, then thisattribute should be left blank.

Bolt1Part is not used in this assembly.

IJUAhsBolt1::Bolt1Rule


a Rule, or a rule ProgID toselect the Bolt1 Part.

IJUAhsBolt1::Bolt1Quantity

Type:LongDefault:[Empty]Purpose: Enter the quantity

of Bolt1 Parts to include on

Base Plate 1.


Type:Double - DistanceDefault:[Empty]

Purpose: Enter the distancethat the first leg should beoffset from the pipe.



a Rule, or a rule ProgID toselect the Offset1 Value.


Type:LongDefault:[Empty]Purpose: Specify howOffset1 should be measured.


Type:Long - CodelistDefault:[By Input]


44/184

44

Purpose: Enter the code listvalue to specify whether theOffset1 be specified by inputor by rule.

Codelist:

hsSelection



Type:Double - DistanceDefault:[Empty]Purpose: Enter the distancethat the second leg should beoffset from the pipe.

This attribute is not used in thisassembly.




select the Offset2 Value.


Type:LongDefault:[Empty]Purpose: Specify howOffset2 should be measured.


Type:Long - CodelistDefault:[By Input]Purpose: Enter the code listvalue to specify whether theOffset2 be specified by inputor by rule.



IJUAhsFrameShoeHeight::ShoeHeightValue

Type:Double - DistanceDefault:[Empty]Purpose: Enter the distancethat the main steel membershould be offset from thepipe.

IJUAhsFrameShoeHeight::ShoeHeightRule




45/184

45

select the ShoeHeight Value.

IJUAhsFrameShoeHeight::ShoeHeightDefinition

Type:LongDefault:[Empty]Purpose: Specify how

ShoeHeight should bemeasured.IJUAhsFrameShoeHeight

::ShoeHeightSelectionType:Long - CodelistDefault:[By Input]Purpose: Enter the code listvalue to specify whether theShoeHeight be specified byinput or by rule.



IJUAhsFrameSpan::SpanValue

Type:Double - DistanceDefault:[Empty]Purpose: Enter the span ofthe frame support after it hasbeen placed by the user.This value can then be usedfor reporting purposes or forsupport validation.

IJUAhsFrameSpan::SpanDefinition

Type:LongDefault:[Empty]Purpose: Specify how Spanshould be measured.

IJUAhsFrameLength1::Length1Value

Type:Double - DistanceDefault:[Empty]Purpose: Enter the lengthof the first leg after thesupport has been placed bythe user. This value can thenbe used for reportingpurposes or for supportvalidation.

IJUAhsFrameLength1::Length1Definition

Type:LongDefault:[Empty]Purpose: Specify howLength1 should bemeasured.


46/184

46


47/184

47

()

Common Section Support Dimensions

IJUAH

grURSCommon::Type

IJUAH

grURSCommon::Family

IJUAH

grURSCommon::PSDetail

IJUAH

grURS_

SectionSize::SectionSize

IJUAH

grURS_

BCDimensions::BraceOffset

IJUAH

grURS_

BCDimensions::BraceOffsetSelect

IJUAH

grURS_

BCDimensions::PipeOffse

t

IJUAH

grURS_

BCDimensions::Overhang

IJUAH

grURS_

BCDimensions::Overhang

Select

IJUAH

grURS_

BCDimensions::BraceAng

le



IJUAHgrURS_SectionSize::SectionSize

Type:StringDefault:[empty]Purpose:Enter the SectionSize to be used for thissupport.

IJUAHgrURS_BCDimensions::BraceOffset

Type:Double - DistanceDefault:[empty]Purpose:This is a usereditable property. The Usercan specify how long the

distance between the pipecenter and the center of topbrace should be.

IJUAHgrURS_BCDimensions::BraceOffsetSelect

Type:Long - CodelistDefault:[By Rule]


48/184

48

Purpose: This is a userselectable property.If selected By Rule, the

BraceOffset will be back tothe default value which isfrom BraceOffset value in

the spreadsheet.If selected By Input, theentered BraceOffset valuewill be applied.

Codelist:URSSelectByRule

1 = By Rule2 = By Input

IJUAHgrURS_BCDimensions::PipeOffset

Type:Double - DistanceDefault:[empty]Purpose:This is a usereditable property. The User

can specify how long thedistance between the pipebottom and the horizontalsection member should be.

The post support will bestretched out verticallydepending on this enteredvalue.

IJUAHgrURS_BCDimensions

::Overhang


Default:[empty]Purpose:This is a usereditable property and can beapplied only whenOverhangSelect is selectedby Input in the next attribute.

The User can specify howlong the distance betweenthe pipe center and the outeredge of horizontal sectionshould be.

The post support will be

stretched out horizontallydepending on this enteredvalue.

IJUAHgrURS_BCDimensions::OverhangSelect

Type:Long - CodelistDefault:[By Rule]Purpose: This is a userselectable property.If selected By Rule, the

Overhang will be back to the


49/184

49

default value which is fromOverhang value in thespreadsheet.If selected By Input, the

entered Overhang value willbe applied.



IJUAHgrURS_BCDimensions::BraceAngle

Type:Double - DegreesDefault:[empty]Purpose:This is a usereditable property. The Usercan specify how the anglebetween the brace sectionand the horizontal oneshould be.


50/184

50


51/184

51

()

Common Section Support Dimensions

IJUA

HgrURSCommon::Type

IJUA

HgrURSCommon::Family

IJUA

HgrURSCommon::PSDetail

IJUA

HgrURS_


IJUA

HgrURS_

ClipSectionSize::ClipSectionSize

IJUA

HgrURS_

FrameSpanDim::Gap1

IJUA

HgrURS_

FrameSpanDim::Gap2

IJUA

HgrURS_

FrameSpanDim::Gap3

IJUA

HgrURS_

FrameSpanDim::Gap4

IJUA

HgrURS_

FrameSpanDim::ClipLen

gth

IJUA

HgrURS_

FrameSpanDim::ClipOffset

IJUA

HgrURS_

FrameSpanDim::StartClips

IJUA

HgrURS_

FrameSpanDim::EndClips




Type:StringDefault:[empty]Purpose:Enter the

Section Size to beused for this support.

IJUAHgrURS_ClipSectionSize::ClipSectionSize

Type:StringDefault:[empty]Purpose:Enter theSection Size to beused for the ClipSections

IJUAHgrURS_FrameSpanDim::Gap1

Type:DoubleDefault:[empty]Purpose:This is a

user editableproperty. The usercan specify thedistance between theoutside of pipe andthe inside of rightcross member.


52/184

52


Type:DoubleDefault:[empty]Purpose:This is auser editableproperty. The usercan specify the

distance between theoutside of pipe andthe inside of left crossmember.


Type:DoubleDefault:[empty]Purpose:This is auser editableproperty. The usercan specify thedistance between theoutside of pipe andthe inside of bottom

cross member.


Type:DoubleDefault:[empty]Purpose:This is auser editableproperty. The usercan specify thedistance between theoutside of pipe andthe inside of topcross member.

IJUAHgrURS_FrameSpanDim::ClipLength

Type:DoubleDefault:[empty]Purpose:This is auser editableproperty. The usercan specify the lengthof the start and endclips.


53/184

53

IJUAHgrURS_FrameSpanDim::ClipOffset

Type:DoubleDefault:[empty]Purpose:This is auser editableproperty. The usercan specify the

distance between theend of the clip to theend of the steelmembers

IJUAHgrURS_FrameSpanDim::StartClips

Type:BitDefault:0Purpose:This is auser editableproperty. The usercan choose whetherthe assembly comeswith the start clips ornot.

IJUAHgrURS_FrameSpanDim::EndClips

Type:BitDefault:0Purpose:This is auser editableproperty. The user

can choose whetherthe assembly comeswith the end clips ornot.


54/184

54

, , &


55/184

55

()

GeneralPipe

Attachment RepadInsulation

Shield Pipe StopFloor

Spring

IJUA

hsSupportNumber::SupportNumbe

r

IJUA

hsPSAttOrient::PipeAttOrientation

IJUA

hsPSHeight::Height

IJUA

hsPSInsClearance::InsulationClea

rance

IJUA

hsPSAttachment::PipeAttPart

IJUA

hsPSAttachment::PipeAttAngle

IJUA

hsPSRepad::RepadPart

IJUA

hsPSRepad::RepadAngle

IJUA

hsPSInsulShield::InsulShieldPart

IJUA

hsPSInsulShield::InsulShieldAngle

IJUA

hsPSPipeStop::PipeStopPart

IJUA

hsPSPipeStop::PipeStopAngle

IJUA

hsPSPipeStop::PipeStopSide

IJUA

hsPSPipeStop::PipeStopQuantity

IJUA

hsPSSpring::FloorSpringPart

Guide Limit StopSlidePlate

BasePlate Stop Plate Bolt

IJUAhsPSGuide::GuidePart

IJUAhsPSGuide::GuideSide

IJUAhsPSGuide::GuideQuantity

IJUAhsPSGuide::GuideSpacing

IJUAhsPSGuide::GuideClearance

IJUAhsPSLimitStop::LimitStopPa

rt

IJUAhsPSLimitStop::LimitStopSide

IJUAhsPSLimitStop::LimitStopQuantity

IJUAhsPSLimitStop::LimitStopSp

acing

IJUAhsPSLimitStop::LimitStopClearance

IJUAhsPSSlidePl::SlidePlatePart

IJUAhsPSSlidePl::SlidePlateAng

le

IJUAhsPSBasePl::BasePlatePart

IJUAhsPSBasePl::BasePlateAng

le

IJUAhsPSStopPl::StopPlatePart

IJUAhsPSStopPl::StopPlateSide

IJUAhsPSStopPl::StopPlateClearance

IJUAhsPSBolt::BoltPart

IJUAhsPSBolt::BoltQuantity


56/184

56


IJUAhsSupportNumber::SupportNumber

Type:StringDefault:[empty]Purpose:Enter the PSDetaildesignation of the support.

This value could be used in theBill of Materials of the support.

IJUAhsPSAttOrient::PipeAttOrientation

Type:Long - CodelistDefault:Purpose:This is a userselectable property. The usercan specify how the supportwants to be oriented.

Codelist:hsSupPipeOrientation1 = Slope

2 = Orthogonal

IJUAhsPSHeight::Height

Type:Double - DistanceDefault:0Purpose:Enter the distancebetween the support and thebottom of pipe.

IJUAhsPSInsClearance

::InsulationClearance


Default:0Purpose:This is a user editableproperty. The user can specifythe clearance of Insulation.

IJUAhsPSAttachment::PipeAttPart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of thePipe Attachment.


57/184

57

IJUAhsPSAttachment::PipeAttAngle

Type:Double - AngleDefault:0Purpose:This is a user editableproperty. The User can specifythe angle of Pipe Attachment tobe orientated about the pipe.

IJUAhsPSRepad::RepadPart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theRepad.

Repad part is not used in this assembly.

IJUAhsPSRepad::RepadAngle

Type:Double - AngleDefault:0Purpose:This is a user editableproperty. The User can specifythe angle of Repad to beorientated about the pipe.

IJUAhsPSInsulShield::InsulShieldPart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theInsulation Shield.

Insulation Shield part is not used in thisassembly.

IJUAhsPSInsulShield::InsulShieldAngle Type:Double - AngleDefault:0Purpose:This is a user editableproperty. The User can specifythe angle of Insulation Shield tobe orientated about the pipe.

IJUAhsPSPipeStop::PipeStopPart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of thePipe Stop.

Pipe Stop part is not used in thisassembly.

IJUAhsPSPipeStop::PipeStopAngle

Type:Double - AngleDefault:0Purpose:This is a user editableproperty. The User can specifythe angle of Pipe Stop to beorientated about the pipe.

IJUAhsPSPipeStop::PipeStopSide

Type:Long - CodelistDefault:Purpose:This is a user


58/184

58

selectable property. The usercan specify how Pipe Stopsshould be placed on both sidesof shoe or only one side.

Codelist:hsSupSide

IJUAhsPSPipeStop::PipeStopQuantity

Type:LongDefault:Purpose:This is a user editableproperty. The user can specifyhow many Pipe Stops should beplaced on each side.

IJUAhsPSSpring::FloorSpringPart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theFloor Spring.

Floor Spring part is not used in thisassembly.

IJUAhsPSGuide::GuidePart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theGuide.

See the image in the above PipeAttachment column.

IJUAhsPSGuide::GuideSide

Type:Long - CodelistDefault:Purpose:This is a userselectable property. The usercan specify how Guides shouldbe placed on both sides of shoeor only one side.

Codelist:hsSupSide

IJUAhsPSGuide

::GuideQuantity

Type:Long

Default:Purpose:This is a user editableproperty. The user can specifyhow many Guides should beplaced on each side.

IJUAhsPSGuide::GuideSpacing

Type:Double - DistanceDefault:0Purpose:This is a user editableproperty. The user can specify


59/184

59

the distance of Guides.

IJUAhsPSGuide::GuideClearance

Type:Double - DistanceDefault:0Purpose:This is a user editableproperty. The user can specify

how long the clearance shouldbe between Guide and the shoe.

IJUAhsPSLimitStop::LimitStopPart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theLimit Stop Plate.

See the image in the above PipeAttachment column.

IJUAhsPSLimitStop::LimitStopSide

Type:Long - CodelistDefault:Purpose:This is a userselectable property. The usercan specify how Limit Stopsshould be placed on both sidesof shoe or only one side.

Codelist:hsSupSide

IJUAhsPSLimitStop::LimitStopQuantity

Type:LongDefault:Purpose:This is a user editableproperty. The user can specifyhow many Limit Stops should beplaced on each side.

IJUAhsPSLimitStop::LimitStopSpacing

Type:Double - DistanceDefault:0Purpose:This is a user editableproperty. The user can specifythe distance of Limit Stops.

IJUAhsPSLimitStop::LimitStopClearance Type:Double - DistanceDefault:0Purpose:This is a user editableproperty. The user can specifyhow long the clearance shouldbe between Limit Stop and thestructure.

IJUAhsPSSlidePl::SlidePlatePart

Type:StringDefault:[empty]

Slide Plate part is not used in thisassembly.


60/184

60

Purpose:Enter the PartNumber or Part Class of theSlide Plate.

IJUAhsPSSlidePl::SlidePlateAngle

Type:Double - AngleDefault:0

Purpose:This is a user editableproperty. The User can specifythe angle of Slide Plate to beorientated about the pipe.

IJUAhsPSBasePl::BasePlatePart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theBase Plate.

Base Plate part is not used in thisassembly.

IJUAhsPSBasePl::BasePlateAngle

Type:Double - AngleDefault:0Purpose:This is a user editableproperty. The User can specifythe angle of Base Plate to beorientated about the pipe.

IJUAhsPSStopPl::StopPlatePart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theStop Plate.

Stop Plate part is not used in thisassembly.

IJUAhsPSStopPl::StopPlateSide

Type:Long - CodelistDefault:Purpose:This is a user

selectable property. The usercan specify how Stop Platesshould be placed on both sidesof shoe or only one side.

Codelist:hsSupSide

IJUAhsPSStopPl::StopPlateClearance

Type:Double - DistanceDefault:0Purpose:This is a user editableproperty. The user can specifyhow long the clearance shouldbe between Stop Place and the

structure.

IJUAhsPSBolt::BoltPart

Type:StringDefault:[empty]Purpose:Enter the PartNumber or Part Class of theBolt.

Bolt part is not used in this assembly.

IJUAhsPSBolt Type:Long


61/184

61

::BoltQuantity Default:Purpose:This is a user editableproperty. The user can specifyhow many Bolts should beplaced.


62/184

62


63/184

63

()

Common Section Size Support Dimensions

IJU

AHgrURSCommon::Type

IJU

AHgrURSCommon::Family

IJU

AHgrURSCommon::PSDetail

IJU

AHgrURS_


IJU

AHgrURS_

BrLPostDim::BraceOffs

et

IJU

AHgrURS_

BrLPostDim::PipeOffse

t

IJU

AHgrURS_

BrLPostDim::Overhang

IJU

AHgrURS_

BrLPostDim::Overhang

Select

IJU

AHgrURS_

BrLPostDim::PostOffse

t

IJU

AHgrURS_

BrLPostDim::PostOffse

tSelect

IJU

AHgrURS_

BrLPostDim::PostOverhang

IJU

AHgrURS_

BrLPostDim::BraceAng

le




Type:StringDefault:[empty]Purpose:Enter the Section Size

to be used for this support.

IJUAHgrURS_BrLPostDim::BraceOffset

Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty. The User can specifyhow long the distance betweenthe pipe center and the center oftop brace should be.

The post support will be stretchedout horizontally depending on thisentered value.


64/184

64

IJUAHgrURS_BrLPostDim::PipeOffset

Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty. The User can specifyhow long the distance betweenthe pipe bottom and the

horizontal section member shouldbe.

The post support will be stretchedout vertically depending on thisentered value.

IJUAHgrURS_BrLPostDim::Overhang

Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty and can be applied onlywhen OverhangSelect is selectedby Input in the next attribute.

The User can specify how longthe distance between the pipecenter and the outer edge ofhorizontal section should be.


IJUAHgrURS_BrLPostDim::OverhangSelect

Type:Long - CodelistDefault:[By Rule]Purpose: This is a userselectable property.If selected By Rule, the

Overhang will be back to thedefault value which is fromOverhang value in thespreadsheet.If selected By Input, the entered

Overhang value will be applied.




65/184

65

IJUAHgrURS_BrLPostDim::PostOffset

Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty and can be applied onlywhen PostOffsetSelect isselected by Input in the next

attribute.The User can specify how longthe distance between the pipecenter and the inner edge ofhorizontal section should be.


IJUAHgrURS_BrLPostDim::PostOffsetSelect

Type:Long - CodelistDefault:[By Rule]Purpose: This is a user

selectable property.If selected By Rule, the Post

offset will be back to the defaultvalue which is from Post offsetvalue in the spreadsheet.If selected By Input, the entered

Post offset value will be applied.



IJUAHgrURS_BrLPostDim::PostOverhang Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty. The User can specifyhow long the distance betweenthe top of horizontal section andthe top edge of vertical sectionshould be.


66/184

66

IJUAHgrURS_BrLPostDim::BraceAngle

Type:Double - DegreesDefault:[empty]Purpose:This is a user editableproperty. The User can specifyhow the angle between the bracesection and the horizontal one

should be.


67/184

67


68/184

68

()

Common Section Size Support Dimensions

IJU

AHgrURSCommon::Type

IJU

AHgrURSCommon::Family

IJU

AHgrURSCommon::PSDetail

IJU

AHgrURS_


IJU

AHgrURS_

TPostDim::PipeOffset

IJU

AHgrURS_

TPostDim::Overhang1

IJU

AHgrURS_

TPostDim::Overhang1S

elect

IJU

AHgrURS_

TPostDim::Overhang2

IJU

AHgrURS_

TPostDim::Overhang2S

elect

IJU

AHgrURS_

TPostDim::PostOffset


Attribute Name Description ImageIJUAHgrURS_SectionSize::SectionSize

Type:StringDefault:[empty]Purpose:Enter the Section Size tobe used for this support.

IJUAHgrURS_TPostDim::PipeOffset

Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty. The User can specify howlong the distance between the pipebottom and the horizontal sectionmember should be.

The post support will be stretched outvertically depending on this enteredvalue.


69/184

69

IJUAHgrURS_TPostDim::Overhang1

Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty and can be applied onlywhen Overhang1Select is selected byInput in the next attribute.

The User can specify how long thedistance between the pipe center andthe outer edge of horizontal sectionshould be.

The post support will be stretched outhorizontally depending on this enteredvalue.

IJUAHgrURS_TPostDim::Overhang1Select

Type:Long - CodelistDefault:[By Rule]Purpose: This is a user selectableproperty.If selected By Rule, the Overhang1

will be back to the default value whichis from Overhang1 value in thespreadsheet.If selected By Input, the entered

Overhang1 value will be applied.



IJUAHgrURS_TPostDim::Overhang2

Type:Double - DistanceDefault:[empty]

Purpose:This is a user editableproperty and can be applied onlywhen Overhang2Select is selected byInput in the next attribute.The User can specify how long the

distance between the pipe center andthe other outer edge of horizontalsection should be.

The post support will be stretched outhorizontally depending on this enteredvalue.

IJUAHgrURS_TPostDim::Overhang2Select

Type:Long - CodelistDefault:[By Rule]Purpose: This is a user selectableproperty.If selected By Rule, the Overhang2

will be back to the default value whichis from Overhang2 value in thespreadsheet.If selected By Input, the entered

Overhang2 value will be applied.


70/184

70



IJUAHgrURS_TPostDim::PostOffset Type:Double - DistanceDefault:[empty]Purpose:Enter the offset value of thevertical section from the center of thehorizontal section.

Purpose:This is a user editableproperty. The User can specify howlong the distance between the verticalsection and the center of horizontalsection should be.


71/184

71


72/184

72

()

Common Spring

IJUAhsCa

talog::Catalog

IJUAHgrU

RSCommon::Type

IJUAHgrU

RSCommon::Family

IJUAHgrU

RSCommon::PSDetail

IJUAHgrU

RS_

CSRodDiameter::RodDiamete

r

IJUAHgrU

RS_

Spring::SpringAssembly

IJUAHgrU

RS_

Spring::SpringType

IJUAHgrU

RS_

Spring::TotalLoad

IJUAHgrU

RS_

Spring::TotalTravel

IJUAHgrU

RS_

Spring::ActualTravel

IJUAHgrU

RS_

ConstantSpring::ConstantSpringPart

IJUAHgrU

RS_

ConstantSpring::ConstantSpringSize

IJUAHgrU

RS_

Spring::TravelDir

IJUAHgrU

RS_

CSMinSize::CSMinSize

IJUAHgrU

RS_

CSMaxSize::CSMaxSize

Top StructureAtt

Bottom PipeAtt Configuration

IJUAHgrU

RS_

SpringStructureAtt::StructureAtt

IJUAHgrU

RS_

SpringPipeAtt::PipeAtt

IJUAHgrU

RS_

PSRSInsulTh::InsulationTh

IJUAHgrU

RS_

RHRotation::Angle

IJUAHgrU

RS_

WithTurnbuckle::WithTurnbuc

kle

IJOAHgrU

RS_

SngTrunL::TrunnionL

IJOAHgrU

RS_

AxialOffset::URS_

AxialOffset

IJOAHgrU

RS_

LateralOffset::URS_

LateralOffset

IJOAHgrU

RS_

PipeAttachOverride::PipeAttO

verride



73/184

73


IJUAHgrURS_CSRodDiameter::RodDiameter

Type:Double - DistanceDefault:12mmPurpose:This is a usereditable property. The user

can change Rod Diameter.

The value entered will applyon both Rods.

IJUAHgrURS_Spring::SpringAssembly

Type:StringDefault:Purpose:Enter the SpringAssembly Name. This isused as the first part of PartNumber of Middle SubAssembly.

The value entered must existon another worksheet.

IJUAHgrURS_Spring::SpringType

Type:StringDefault:Purpose:Enter the type ofthe Spring to use. This isused as the last part of PartNumber of Middle SubAssembly.

IJUAHgrURS_Spring::TotalLoad

Type:Double - ForceDefault:[empty]Purpose:This is a usereditable property. The usercan enter the value as theTotal Load.

For details of these values,refer to the Constant SpringSmartPart documentation.

IJUAHgrURS_Spring::TotalTravel

Type:Double - DistanceDefault:[empty]Purpose:This is a usereditable property. The usercan enter the value as the

Total Travel.

IJUAHgrURS_Spring::ActualTravel

Type:Double - DistanceDefault:[empty]Purpose:This is a usereditable property. The usercan enter the value as theActual Travel.


74/184

74

IJUAHgrURS_ConstantSpring::ConstantSpringPart

Type:Long - CodelistDefault:12Purpose:Enter the code listvalue of Constant Spring.

Codelist:

RSConstantSpringPart(The followings areexamples.)

1 = Bergen Power 4000, Constant,Type A12 = Bergen Power 4000, Constant,Type B1a3 = Bergen Power 4000, Constant,Type B1

IJUAHgrURS_ConstantSpring::ConstantSpringSize

Type:LongDefault:1Purpose:This is a usereditable property. The user

can choose what size ofConstant Spring the Userwant to place.

IJUAHgrURS_Spring::TravelDir

Type:Long - CodelistDefault:DownPurpose:This is a usereditable property. The Usercan specify which directionSpring would be moved.

Codelist:URSSpringTravelDir

1 = Up2 = Down

IJUAHgrURS_CSMinSize::CSMinSize

Type:LongDefault:1Purpose:Enter the MinimumSize of Constant Spring.

IJUAHgrURS_CSMaxSize::CSMaxSize

Type:LongDefault:68Purpose:Enter the MaximumSize of Constant Spring.


75/184

75

IJUAHgrURS_SpringStructureAtt::StructureAtt

Type:StringDefault:[empty]Purpose:Enter the partnumber or part class of TopSub Assembly.


IJUAHgrURS_SpringPipeAtt::PipeAtt

Type:StringDefault:[empty]Purpose:Enter the partnumber or part class ofBottom Sub Assembly.


IJUAHgrURS_PSRSInsulTh::InsulationTh

Type:StringDefault:[Empty]Purpose:This is a usereditable property. The Usercan choose which theInsulation Thickness is usedfor the Riser Clamp.

Codelist:URSPipeShieldRSInsulTh

1 = 12 = 23 = 34 = 4


76/184

76

IJUAHgrURS_RHRotation::Angle

Type:Long - CodelistDefault:90 DegreesPurpose:This is a usereditable property. The Usercan specify how they wantthe structural attachment to

be orientated.

Rotates the top attachmentabout the rod.

Codelist:URSAngle

0 = 0 Degrees90 = 90 Degrees180 = 180 Degrees270 = 270 Degrees

IJUAHgrURS_WithTurnbuckle::WithTurnbuckle

Type:BitDefault:0Purpose:This is a usereditable property. The usercan choose whether theassembly comes with theTurnbuckle or not.

IJOAHgrURS_SngTrunL::TrunnionL

Type:Double - DistanceDefault:[Empty]Purpose:This is a usereditable property. The usercan specify how long theTrunnion Length should be.


77/184

77

IJOAHgrURS_AxialOffset::URS_AxialOffset

Type:Double - DistanceDefault:0Purpose:This is a usereditable property. The usercan enter the offset theyrequire on Rod Hanger.

The value entered will offsetonly Rod Hanger subassemblies along the pipe ifthis is allowed.

IJOAHgrURS_LateralOffset::URS_LateralOffset

Type:Double - DistanceDefault:0inPurpose:This is a usereditable property. The usercan enter the offset theyrequire on Rod Hanger.

The value entered will offsetonly Rod Hanger subassembly lateral the pipe.


78/184

78

IJOAHgrURS_PipeAttachOverride::PipeAttOverride

Type:Long - CodelistDefault:DefaultPurpose:This is a usereditable property. The Usercan specify which Pipe Clampshould be used.

Codelist:URSPipeAttachOverride(The followings areexamples.)

1 = Default2 = JIMCCmp_NPCB-L - 0203 = JIMCCmp_NPCB-L - 0254 = JIMCCmp_NPCB-L - 032

Top Sub Assembly refers to Top Sub Assembly Attributes (SCT_TOP).

Middle Sub Assembly refers to Middle Sub Assembly Attributes (CS_Middle).

Bottom Sub Assembly refers to Bottom Sub Assembly Attributes (CLAMP_BOT).


79/184

79


80/184

80

()

Common Spring

IJUAhsCatalog::Catalog

IJUAHgrURSCommon::Type

IJUAHgrURSCommon::Family

IJUAHgrURSCommon::PSDetail

IJUAHgrURS_

CSRodDiameter::RodDiameter

IJUAHgrURS_

Spring::SpringAssembly

IJUAHgrURS_

Spring::SpringType

IJUAHgrURS_

Spring::TotalLoad

IJUAHgrURS_

Spring::TotalTravel

IJUAHgrURS_

Spring::ActualTravel

IJUAHgrURS_

ConstantSpring::ConstantSpringPart

IJUAHgrURS_

ConstantSpring::ConstantSpringSize

IJUAHgrURS_

Spring::TravelDir

IJUAHgrURS_

CSMinSize::CSMinSize

IJUAHgrURS_

CSMaxSize::CSMaxSize

Top StructureAtt

Bottom PipeAtt Configuration

IJUAHgrURS_

SpringStructureAtt::Structure

Att

IJUAHgrURS_

SpringPipeAtt::PipeAtt

IJUAHgrURS_

PSRSInsulTh::InsulationTh

IJUAHgrURS_

DblRHRotation::Angle1

IJUAHgrURS_

DblRHRotation::Angle2

IJUAHgrOrientation::OrientationAngle

IJUAHgrOrientation::Orientation

IJOAHgr

URS_

AxialOffset::URS_

AxialOffse

t

IJOAHgr

URS_

LateralOffset1::URS_

LateralOffset1

IJOAHgr

URS_

LateralOffset2::URS_

LateralOffset2

IJOAHgr

URS_

RClampOverride::RClampOverride

IJUAHgrURS_

WithTurnbuckle::WithTurnbu

ckle



81/184

81


IJUAHgrURS_CSRodDiameter::RodDiameter

Type:Double - DistanceDefault:12mmPurpose:This is a user editableproperty. The user can change

Rod Diameter.

The value entered will apply onboth Rods.

IJUAHgrURS_Spring::SpringAssembly

Type:StringDefault:Purpose:Enter the SpringAssembly Name. This is used asthe first part of Part Number ofMiddle Sub Assembly.

The value entered must exist on

another worksheet.

IJUAHgrURS_Spring::SpringType

Type:StringDefault:Purpose:Enter the type of theSpring to use. This is used as thelast part of Part Number of MiddleSub Assembly.

IJUAHgrURS_Spring::TotalLoad

Type:Double - ForceDefault:[empty]Purpose:This is a user editableproperty. The user can enter thevalue as the Total Load.

For details of these values, refer tothe Constant Spring CatalogSmartPart documentation.

IJUAHgrURS_Spring::TotalTravel

Type:Double - DistanceDefault:[empty]Purpose:This is a user editableproperty. The user can enter thevalue as the Total Travel.

IJUAHgrURS_Spring::ActualTravel

Type:Double - DistanceDefault:[empty]

Purpose:This is a user editableproperty. The user can enter thevalue as the Actual Travel.

IJUAHgrURS_ConstantSpring::ConstantSpringPart

Type:Long - CodelistDefault:12Purpose:Enter the code list valueof Constant Spring.


82/184

82

Codelist:RSConstantSpringPart(The followings are examples.)

1 = Bergen Power 4000, Constant, Type A12 = Bergen Power 4000, Constant, Type B1a3 = Bergen Power 4000, Constant, Type B1

IJUAHgrURS_ConstantSpring::ConstantSpringSize

Type:LongDefault:1Purpose:This is a user editableproperty. The user can choosewhat size of Constant Spring theUser want to place.

IJUAHgrURS_Spring::TravelDir

Type:Long - CodelistDefault:DownPurpose:This is a user editableproperty. The User can specifywhich direction Spring would bemoved.

Codelist:URSSpringTravelDir

1 = Up2 = Down

IJUAHgrURS_CSMinSize::CSMinSize

Type:LongDefault:1Purpose:Enter the Minimum Sizeof Constant Spring.

IJUAHgrURS_CSMaxSize::CSMaxSize

Type:LongDefault:68Purpose:Enter the Maximum Sizeof Constant Spring.

IJUAHgrURS_SpringStructureAtt::StructureAtt

Type:StringDefault:[empty]Purpose:Enter the part number orpart class of the top sub assembly.

The value entered must exist onanother worksheet.

IJUAHgrURS_SpringPipeAtt::PipeAtt

Type:StringDefault:[empty]Purpose:Enter the part number or

part class of the bottom subassembly.

The value entered must exist onanother worksheet.

IJUAHgrURS_PSRSInsulTh::InsulationTh



83/184

83

Purpose:This is a user editableproperty. The User can choosewhich the Insulation Thickness isused for the Riser Clamp.

Codelist:

URSPipeShieldRSInsulTh

1 = 12 = 23 = 34 = 4

IJUAHgrURS_DblRHRotation::Angle1

Type:Long - CodelistDefault:90Purpose:This is a user editableproperty. The User can specifyhow they want the Rod Hanger1 tobe orientated.

Rotation is in reference to bothTop and Middle Sub Assemblyobjects.

Codelist:URSAngle

0 = 0 Degrees90 = 90 Degrees180 = 180 Degrees270 = 270 Degrees

IJUAHgrURS_DblRHRotation::Angle2


Purpose:This is a user editableproperty. The User can specifyhow they want the Rod Hanger2 tobe orientated.

Rotation is in reference to bothTop and Middle sub assemblyobjects.

Codelist:URSAngle

0 = 0 Degrees90 = 90 Degrees

180 = 180 Degrees270 = 270 Degrees


84/184

84

IJUAHgrOrientation::OrientationAngle

Type:Double - AngleDefault:0Purpose:This is a user editableproperty. The User can specifyhow they want the entire risersupport to be orientated about the

pipe.

IJUAHgrOrientation::Orientation

Type:Long - CodelistDefault:N-SPurpose:This is a user editab

assembly xls columns for sct supports.pdf

Documents