audio-visual solutions hdmi installation training analog to digital, simple to sophisticated, all...
TRANSCRIPT
Audio-Visual Solutions
HDMI Installation TrainingAnalog to Digital, simple to sophisticated, all from one source!
Who is Intelix?
Founded in 1986Based in Middleton, WI USAEngineering heritageHistorically Pro-AudioToday 90% Video
Who is Intelix?
Market SegmentsPro AV
Residential CI
DataComSecurity-CCTV
Product Categories
HDMI SystemsDigital Signage SystemsPassive and Active Twisted Pair Extension SolutionsSecurity Distribution ProductsAudio Matrix SystemsRoom Combine SystemsPaging Systems
Who is Intelix?
Before we start…The most current Installation Manuals and Software are located at:www.intelix.com under “Technical Library”
HDMI Product Installation
Installing the DIGI-HD-UHR2 and DIGI-HD-IR2
HDMI Product Installation
1080p 1080i 720p 480i/p
Cat 6 (low-skew)
150’ 300’ 300’ 350’
Cat 6 110’ 220’ 220’ 220’
Cat 5e 100’ 200’ 200’ 200’
1080p 1080i 720p 480i/p
Cat 6 (shielded)
150’ 300’ 300’ 350’
Cat 6 110’ 220’ 220’ 220’
Cat 5e 100’ 200’ 200’ 200’
Installation Considerations
Installing the UTP Extenders
Use the EIA/TIA 568B Crimp PatternPower is required on send and receive extendersThird-party IR systems are not compatible with the DIGI-HD-IR2
(Intelix is a 5V system)The extenders will feel warm (98 degrees F)Do not connect the balun to a telecommunication outlet wired to
unrelated equipment. Ensure all connected twisted pair cabling is straight-through
(point-to-point)
Instructions Power off all AV equipment Make sure you have a point-to-point circuit. Make sure source and display work with HDMI cable Test the HDMI patch cables
Installing the UTP Extenders
Instructions Connect the DIGI-HD-UHR2 transmitter to the source then the
receiver to the display (no power) Connect the CAT cable
Installing the UTP Extenders
Instructions Power on the receiver then transmitter Power on the source and display devices Verify picture quality
Installing the UTP Extenders
Copying EDID - DIGI-HD-UHR2
Disconnect the transmitter and receiverConnect transmitter to display with HDMI cable
Installing the UTP Extenders
Copying EDID - DIGI-HD-UHR2
Press “Hand Shake” button LEDs will flash and then remain solidEDID is copied Disconnect transmitter and repeat normal
installation
Installing the UTP Extenders
Bandwidth Shaping DIGI-HR-UHR2
Position 1 Position 2 Mode
Off Off Use copied EDID data from display
Off On Turn on Dolby TrueHD and DTS-HD
On Off Turn on stereo audio
On On No function
Installing the UTP Extenders
Transmitter DIP Switch Positions
Unplug all of the cables to make DIP switch changesChange the DIP switch position Reconnect the transmitter
The UHR2 will not pass EDID information from the display to the source
Bandwidth Shaping DIGI-HR-IR2
Position 1 Position 2 Mode
Off Off Read EDID data from displays
Off On Turn on Dolby TrueHD and DTS-HD
On Off Turn on stereo audio
On On No function
Installing the UTP Extenders
Transmitter DIP Switch Positions
Unplug all of the cables to make DIP switch changesChange the DIP switch position Reconnect the transmitter
The IR2 will pass EDID information from the display to the source.
Using IR with the DIGI-HD-IR2Disconnect power from BalunsAttach emitter to source and eye to display
Plug the emitter into send side of DIGI-HD-IR2Plug the eye into the receive side of DIGI-HD-IR2
Installing the UTP Extenders
Using IR with the DIGI-HD-IR2
Power the extenders and test IR
Installing the UTP Extenders
Installing the DIGI-HD-COAX-S and the DIGI-HD-COAX-R
HDMI Product Installation
1080p 1080i 720p
RG6 300’ 675’ 675’
RG59 250’ 675’ 675’
Installation Considerations
• Will only run at 3 resolutions• 720p-60• 1080i-30• 1080p-60
• DVI will only work at the available resolutions• Source equipment will need to be forced into available
resolutions• No taps, splitters, amps, pads or filters• Works with barrels or F-connectors• Needs a minimum of 50’ of 75 Ohm cable• Does not pass 3D
Installing the DIGI-COAX
Instructions Power off all AV equipment Make sure you have a point-to-point circuit. No taps, splitters, amps, pads or filters Works with barrels or f-connectors
Installing the DIGI-COAX
Instructions Connect the transmitter to the source
then the receiver to the display (no power)
Connect the COAX cable to the “A” side of the transmitter (BNC or F-connector)
Connect the Coax to the “input” on the receiver
Installing the DIGI-COAX
Instructions Power on the receiver then transmitter Power on the source and display devices Verify picture quality
Installing the DIGI-COAX
HDMI Digital Signage Application
Installing the DIGI-COAX
Installing the DIGI-SCAL-11x2
HDMI Product Installation
Switcher/Format Converter/Scaler
DIGI-SCAL-11x2
Installing the DIGI-SCAL-11x2
Installation Considerations
• HDMI outputs are mirrored not matrixed• 3 to 5 second switch time• Video blue screen during switch process• Volume cannot be changed• It will not convert audio from digital or analog stereo to multi
channel digital audio• It will only convert analog stereo audio to PCM digital stereo
audio and back.
Installing the DIGI-SCAL-11x2
Installation Instructions
Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-SCAL-11X2 requires one rack unit of spacing.)
Installing the DIGI-SCAL-11x2
Installation Instructions
Power off source and destination devicesConnect input sources Connect output destination(s)
Installing the DIGI-SCAL-11x2
Installation Instructions Connect power supply Connect RS232 or IR if the unit is remote controlled Power on DIGI-SCAL-11x2 Power on source and designation devices
Installing the DIGI-SCAL-11x2
Operation – Channel Pairing
• Audio and Video pairing are as follows:
Installing the DIGI-SCAL-11x2
Input Video Format Audio Format1 Compsite Stereo Audio2 Compsite Stereo Audio3 YPbPr Stereo Audio4 YPbPr Stereo Audio5 VGA Stereo Audio6 S-Video Stereo Audio7 DVI-I Stereo Audio & Digital audio8 HDMI Digital audio9 HDMI Digital audio10 HDMI Digital audio
Operation – Channel Pairing
• VGA Audio
• S-video Audio
• DVI-I
Installing the DIGI-SCAL-11x2
Built-in Audio Conversion and Embedding
Installing the DIGI-SCAL-11x2
Analog Stereo Audio In
Analog Audio Out
PCM Digital Audio Out
PCM Digital Audio In
PCM Digital Audio OutAnalog Audio Out
PCM Digital Audio Out
PCM Digital Audio Out
Operation – Front Control Panel
• Power on the unit by selecting the Standby button.• Select the input with the rotary knob.• Select output resolution with the Mode Selection button.
Installing the DIGI-SCAL-11x2
Operation – Supported Signal Formats
Input Signal Format
Composite PAL, NTSC
S-video PAL, NTSC
YPbPr 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
VGA 800x600, 1024x768, 1152x864, 1280x768, 1280x960,1280x1024, 1440x900, 1400x1050, 1600x1200, 1920x1200
DVI-I 800x600, 1024x768, 1152x864, 1280x768, 1280x960,1280x1024, 1440x900, 1400x1050, 1600x1200, 1920x1200
HDMI 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Installing the DIGI-SCAL-11x2
Output Signal Format
HDMI 720p, 1080p
Operation – Included Remote Control
Installing the DIGI-SCAL-11x2
Function DescriptionA Standby Toggles on and off standby mode (low power mode)B Source Selection Directly selects an audio-visual inputC Menu Toggles the onscreen menuD Info Toggles the input and output messagingE Source Scrolling Toggles the next or previous audio-visual inputF PC Bypass Toggles on and off PC bypass modeG 720p Mode Toggles the output mode to 720pH 1080p Mode Toggles the output mode to 1080p
Operation – PC Bypass Mode• PC Bypass Mode allows a computer’s native resolution to display on the destination monitor.• When using PC Bypass Mode, the front panel indicators will disable. In addition, the default
output will be in 1080p.• PC Bypass mode will only function when a VGA or DVI signal is present and my be activated
from the remote control or the “Mode Selection” button.
Installing the DIGI-SCAL-11x2
Input 800x600, 1024x768, 1152x864, 1280x720, 1280x960,1280x1024, 1440x900, 1600x1200, 1920x1080Output 800x600, 1024x768, 1152x864, 1280x720, 1280x960,1280x1024, 1440x900, 1600x1200, 1920x1081
PC Bypass Supported Resolutions
Operation – On Screen Display
Installing the DIGI-SCAL-11x2
Operation – RS232 Remote Control• The manual has a complete list of the RS232 control codes• Connect a straight-through serial cable directly to the matrix
Installing the DIGI-SCAL-11x2
9600 baud rate8 data bits1 stop bitNo parity bitNo handshake
Installing the DIGI-HD-4X4 and 4X2
HDMI Product Installation
DIGI-HD-4X4
Installing the DIGI-HD-4X4
Installation Considerations• “A” and “B” RJ45 jacks on the output will only connect to one
DIGI-HD-UHR2-R or DIGI-HD-IR2-R • You can mix DIGI-HD-UHR2-R or DIGI-HD-IR2-R• Consider buying and extra DIGI-HD-UHR2-S to make copying
EDID from the displays easier.
Installing the DIGI-HD-4X4 and 4X2
Installation Instructions
Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-HD-4X4 requires one rack unit of spacing.)
Installing the DIGI-HD-4X4
Installation Instructions
Power off source and destination devicesConnect input sources Connect output destination to HDMI or twisted pair
Installing the DIGI-HD-4X4
Installation InstructionsRecommended Twisted Pair Receivers
Installing the DIGI-HD-4X4
1080p 1080i 720p 480i/p
Cat 6 (shielded)
150’ 300’ 300’ 350’
Cat 6 110’ 220’ 220’ 220’
Cat 5e 100’ 200’ 200’ 200’
Installation Instructions
Installing the DIGI-HD-4X4
Twisted Pair Settings-Toggle all Ports1. To toggle between single and dual twisted pair modes,
simultaneously press and hold the Output 3 button and Key-lock button for 3 seconds.
2. Use Output 1 and Output 2 and Key-lock to toggle the DIGI-HD-4X2 3. The default setting of the DIGI-HD-4X4 is double twisted pair
mode.
Installation Instructions
Installing the DIGI-HD-4X4
Twisted Pair Settings-Using ComCtl software
Installation Instructions
Installing the DIGI-HD-4X4
Signal Mode Settings set by DIP switches: HDshāk Inside
EDID CopyBandwidth Shaping
Installation Instructions
Installing the DIGI-HD-4X4
DIP Switch Mode SettingsDIP 1 DIP 2 DIP 3 EDID Function
off off off Dual Twisted Pair Mix ModeThe matrix mixes the EDID data of all destinationswhich choosing the same source. This data is thentransmitted by the matrix to the source device. Tocopy and sync the EDID data, simultaneously pressand hold the Output 1 button and Keylock buttonfor 3 seconds.off off on EDID Copy ModeEDID data is copied from the selected output andtransmitted to the desired input. To copy and syncthe EDID data, press and hold the output button ofthe selected output for 3 seconds.
off on off Factory Default: 1080p with stereo audioThe matrix is preset with EDID data for 1080pvideo and stereo audio.
off on on Factory Default: 1080i with stereo audioThe matrix is preset with EDID data for 1080i videoand stereo audio.
on off off Factory Default: 1080p with 5.1 audioThe matrix is preset with EDID data for 1080pvideo and 5.1 audio.
on off on Factory Default: 1080p with 7.1 audioThe matrix is preset with EDID data for 1080pvideo and 7.1 audio.
Installation Instructions
Connect the included 12 VDC power supply to the DIGI-HD-4x4.
If controlling remotely, connect RS232, Ethernet, or IR control cables.
Power-on the DIGI-HD-4x4. Power-on the source and destination audio and
video devices. Power off DIGI-HD-4X4 before changing the DIP
switches to change signal mode. Power up to have changes take effect.
Installing the DIGI-HD-4X4
Operation
Front Panel Control Basics
Installing the DIGI-HD-4X4
Operation• Included Remote Control
Installing the DIGI-HD-4X4
Operation - SetupIR Remote Control
Installing the DIGI-HD-4X4
Operation - SetupRS232 and Ethernet Remote Control
Installing the DIGI-HD-4X4
Web Control
DHCP or Static IP address
Installing the DIGI-HD-8X8
HDMI Product Installation
DIGI-HD-8X8
Installing the DIGI-HD-8X8
Installation Considerations• “A” and “B” RJ45 jacks on the output will only connect to one
DIGI-HD-UHR2-R or DIGI-HD-IR2-R • Use only DIGI-HD-UHR2-R or DIGI-HD-IR2-R for all 8 extension
out puts. Do not mix.• Consider buying and extra DIGI-HD-UHR2-S to make copying
EDID from the displays easier.
Installing the DIGI-HD-8X8
Installation Instructions
Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-HD-8X8 requires four rack units of spacing.)
Installing the DIGI-HD-8X8
Installation Instructions
Power off source and destination devicesConnect input sources Connect output destination to HDMI or twisted pair
Installing the DIGI-HD-8X8
Installation InstructionsRecommended Twisted Pair Receivers
Installing the DIGI-HD-8X8
1080p 1080i 720p 480i/p
Cat 6 (shielded)
150’ 300’ 300’ 350’
Cat 6 110’ 220’ 220’ 220’
Cat 5e 100’ 200’ 200’ 200’
Installation Instructions
Installing the DIGI-HD-8X8
Signal Mode Settings set by DIP switches: HDshāk Inside
Single or Dual EDID CopyBandwidth Shaping
Installation Instructions
Installing the DIGI-HD-8X8
DIP Switch Mode Settings
With DIGI-HR-UHR2-R
Installing the DIGI-HD-8X8
Example setup:Inputs (3) Satellite boxes (1) DVD Player
Outputs (2) Local TVs (2) Remote TVs
Installing the DIGI-HD-8X8
Example setup:Inputs (3) Satellite boxes (1) DVD Player
Outputs (2) Local TVs (1) Remote TVs with IR remote
With DIGI-HR-IR2-R
Installation Instructions Connect the included 12 VDC power supply to the
DIGI-HD-8X8. If controlling remotely, connect RS232, Ethernet,
or IR control cables. Power-on the DIGI-HD-8X8. Power-on the source and destination audio and
video devices. Power off DIGI-HD-8X8 before changing the DIP
switches to change signal mode. Power up to have changes take effect.
Installing the DIGI-HD-8X8
Operation
Front Panel Control Basics
Installing the DIGI-HD-8X8
Default PasswordsUser: 1234Admin: HDMI
Operation
Selection using “Room View”
Installing the DIGI-HD-8X8
Operation
Selection using “Matrix View”
Installing the DIGI-HD-8X8
OperationSelect a “Preset”
Installing the DIGI-HD-8X8
or
OperationSet a new “Preset”
Installing the DIGI-HD-8X8
Operation – User access Lock Screen
Installing the DIGI-HD-8X8
Unlock Screen
Operation - SetupOpening the “Utilities” menu as administrator
Installing the DIGI-HD-8X8
Operation - SetupSet User and Admin passwords
Installing the DIGI-HD-8X8
or
Operation - SetupDefine Input Icons
Installing the DIGI-HD-8X8
Operation - SetupDefine Input Text Label
Installing the DIGI-HD-8X8
Operation - SetupCopy EDID when using DIGI-HD-UHR2-R receivers
Installing the DIGI-HD-8X8
or
Operation - SetupDefine Output Icons
Installing the DIGI-HD-8X8
Operation - SetupDefine Output Text Label
Installing the DIGI-HD-8X8
Operation - SetupReset System Settings
Installing the DIGI-HD-8X8
Operation - SetupIncluded Remote Control• Directly with Matrix
– Buttons 1 to 8 are destinations– Arrows are “previous” and “next” source
• Through Extender– Extender location defines output– Buttons 1 to 8 represent inputs– Discretely choose inputs
Installing the DIGI-HD-8X8
Operation - SetupIR Remote Control
Extend the IR sensor with the included “eye” -Plug it directly into the 3.5mm jack in
the back of the unit-Third-party IR devices are not
compatible with the 3.5mm jack
Using third-party IR control-Connect from base IR control unit using
Ethernet or RS232-IR control – attached emitter to IR
pickup on the front for the unit
Installing the DIGI-HD-8X8
Operation - Setup
RS232 Remote Control
• RS232 programming and command information is Appendix A of the manual• Must receive all messages in hexadecimal number code.• If messages are transmitted in decimal or ASCII codes, they will fail to work.
Installing the DIGI-HD-8X8
Operation - Setup
Ethernet Remote Control• Connect an Ethernet cable directly to the matrix. • The DIGI-HD-8X8 will automatically be assigned an IP address when connected to a
DHCP-enabled network. By default, DHCP is enabled.• Within 10 seconds of connecting the DIGI-HD-8X8 to the LAN, the yellow LED on the
matrix’s Ethernet port will stop blinking and the green LED will blink intermittently.• For Ethernet programming and command information, see Appendix A
Installing the DIGI-HD-8X8
Operation - Setup
Web Control
Installing the DIGI-HD-8X8
Operation - Setup
IR Twisted Pair Pass-Through Determine which devices you wish to control via the IR pass-through outputs. Connect an IR emitter to the desired IR transmit output port. Repeat for up to eight devices. All of the remote receive baluns transmit IR commands from the included remote
control, thereby allowing remote control of the matrix itself. Verify that IR pass-through is enabled in the front panel LCD Utilities screen.
Installing the DIGI-HD-8X8
Why Intelix?
Maximize Performance:Complete integrated solution approach
HDMI
Why Intelix?
HDMI
Insured Reliability:Multi Stage Quality Assurance Process
Less than a 1% return rate
Why Intelix?
HDMI
World Class Support:Pre and post sales technical
and applications support90 day advanced replacement2 year warranty on all products
Intelix ContactsTechnical Sales /Training: Brad Weisbrod | [email protected] Status: Ellen Domine | [email protected] Inquiries: Beth Green | [email protected] Support: Sterling Glass | [email protected] Inquiries: Eric Lang | [email protected]
Domestic Sales Questions: Cameron Smith | [email protected]
International Sales Questions: Steve Cohan | [email protected]
608-831-0880 phone | 608-831-1833 fax | www.intelix.com
Intelix
Resources
608-831-0880 phone | 608-831-1833 fax | www.intelix.com
Intelix
Literature Library: http://www.intelix.com/tech_library/marketing_lit.aspx
Product Technical Literature: http://www.intelix.com/tech_library.htm