auto passport - innovative control systems...rfid wiri g oriplt la t laynuo auon st ory fltx lane #1...
TRANSCRIPT
Auto Passport®
with the All-In-One RFID Reader/ Antenna for the Auto Sentry® flex
Installation Guide - Version 3.0
November 8, 2019
Auto Passport Installation GuidePage 1 Copyright © Innovative Control Systems, Inc.
Installation OverviewThank you for purchasing your Auto Passport, the ICS® radio frequency identification system. This document was written for technicians and electricans installing the Auto Passport. A thorough understanding of electrical wiring, installation, codes, and safety protocols is required. No prior experience with the Auto Passport is necessary. By reading the information and performing the procedures in this installation guide, you should be able to install the Auto Passport system-level and communications wiring.
�NOTE: � The Auto Passport is not a stand-alone system. WashConnect and a connection to an Auto Sentry is required.
System Components � The protective enclosure houses the RFID reader and antenna.
� One All-In-One RFID Reader / Antenna Enclosure per lane is to be installed on an overhead truss or canopy above the lane near the Auto Sentry flex so vehicles can drive underneath it.
� The RFID All-In-One Reader/Antenna power and data cable terminates at the terminal blocks located in the base of Auto Sentry flex.
� The RFID All-in-One Cable is 35’ in length.
Truss Size InformationTrusses are available in two sizes:
� A 95-inch truss to be installed on curbs or raised islands.
� A 100-inch truss to be installed on ground-level surfaces.
This guide should be supplied to the electrician prior to the installation of conduits and wiring to ensure the Auto Passport is installed properly. Faulty installations are the major cause of system malfunctions. The Auto Passport must be installed exactly as described in this installation guide to ensure its reliability and safe operation.
WAR�I�GE: Failure to properly install the Auto Passport could result in serious injury or death and will void the warranty.
Version ConsiderationsThis version 3.0 of the installation guide, released on November 5, 2019. WashConnect Software version of 1.6.7 or higher.
Site PlanningCareful planning for the layout of the site will help eliminate possible problems with the start-up of your system and will ensure continued, reliable system operation. In determining the location stage, keep the following objectives in mind:
� The Auto Passport has been designed to operate in an outdoor environment.
Figure 1. All-In-One RFID Reader / Antenna Enclosure
Figure 2. Internal view of Enclosure displaying the RFID Reader Card
Figure 3. RFID All-In-One Cable
Auto Passport Installation GuidePage 2 Copyright © Innovative Control Systems, Inc.
Hardware Specs � The Auto Passport is designed to be located in all types of conditions, cold, wet, or hot.
� The unit has been designed to operate in the temperature range of -20° F to120° F (-28 °C to 48 °C).
� The RFID Antenna enclosure is mounted on a truss that is bolted to the concrete floor.
� Dedicated universal power supply (UPS): 1500VA/865 Watts output capacity.
� RFID All-In-One Reader / Antenna Enclosure Equipment Measurements, and Ratings:
Planning for Installation � Prepare to have all the necessary tools and parts.
� Ensure Auto Sentry island specifications are met.
� Ensure permanent connections are performed by a licensed electrician who must comply with the National and Local recommended standards.
� Wiring can be contained in rigid PVC conduit or metal conduit.
� High-voltage (AC) and low-voltage (DC) must not be combined in a common conduit, junction box, or wire trough.
� Power for the Auto Passport and any peripherals must come from the dedicated UPS, as supplied by ICS, and must be properly grounded.
� Check through all shipping containers before disposing of them looking for possible manuals, cables, connectors, etc.
Warning Markings
Technical SupportInnovative Control Systems® provides a toll-free number for customers and installers for installation questions: 800-246-3469.
!The symbol on the left is labeled on equipment and hardware to indicate one should consult accompanying documentation before proceeding.
Dimension Amount
Width 10 - 1/2 in / 26.7 cm
Length 30 in / 76.2 cm
Depth 5- 1/2 in / 13.9 cm
Weight 30.0 lbs / 13.6 kg
Operating Temp. Range -20° F to 120° F
-28° C to 48° C
Frequency 902.75 – 927.25 MHz
Supply Voltage 24V DC
Max. Current 10 Amps @ 120 V AC
RF Power Max 4 watts EIRP with antenna
Table 1: RFID All-In-One Reader/Antenna Enclosure Measurements, and Ratings
Auto Passport Installation GuidePage 3 Copyright © Innovative Control Systems, Inc.
Auto Sentry flex Island Specifications � �NOT 1E: The length of the island should be determined by the car wash owner, but ICS recommends that the island be
a minimum of 18’ - 0” in length. This will provide for adequate space for the proper placement of the Auto Sentry and its gate. If menu signs and other items are to be installed on the island, then it is the car wash owner’s responsibility to increase the length of the island to accommodate these additional items. See Figure 4.
� �NOT #2E: ICS highly recommends that the width of the islands be a minimum of 4’ - 6” for the safety of the attendants when servicing. This measurement, along with the proper placement of the Auto Sentry, will prevent the rear of the Auto Sentry from hanging over into another drive-thru lane and provides ample room for vehicles to pass through the lanes without striking the rear of an Auto Sentry.
� �NOT #3E: The height of the island, above the final finished grade upon which a vehicle will rest, must be 6”. This will ensure that the Auto Sentry is at the optimum height for customers using the Auto Sentry while seated in their vehicles.
� �NOT #4E: At the car wash owner’s discretion, the installation of bollards at the entrance end of the island is highly recommended and will minimize the chances of vehicles striking and damaging an Auto Sentry or Traffic gate. Bollards should be located so that they provide protection to ICS equipment but also offer ample clearance so that the equipment can be easily installed and maintained.
� �NOT #5E: Any canopy that is above both the Auto Sentry and the optional Traffic Gate must be a minimum of 12’ - 6” from the base of the gate to the bottom of the canopy to allow the gate to open fully without striking the canopy.
� �NOT #6E: The bill dispenser is in the base of the payment terminal and swings open 2’ – ½ “ towards the exit end of the island. This must be taken into consideration when setting canopy posts and RFID trusses. When dual post canopies are used, there must be a 2’ - 6” clearance on the right side of the payment terminal. If the inside width is not at least 60” then the post must be mounted to the rear of the payment terminal which will require a minimum of 1’ - 6” from the Auto Sentry. Contact an ICS Representative if there is any concern regarding canopy placement.
15 “ X 27 1/2” BASE
WITH DOORS
15 “ X 27 1/2” BASE
WITH DOORS
15 “ X 27 1/2” BASE
WITH DOORS
15 “ X 27 1/2” BASE
WITH DOORS
CLEARANCE: A MINIMUM OF 24" DIAMETER OF CLEARANCE FROM THE CENTER OF THE
GATE AND BARRIER IN ALL DIRECTIONS.
1' -
0"
10' - 0"
1' -
7"
FOOTPRINT OF AUTO SENTRY
2' -
5”
2' - 0"
CLCL
CLCL
MINIMALLY 18' - 0"SEE NOTE #1
4' -
6"S
EE
NO
TE
#2
3" DIA. CONCRETE FILLED BOLLARD
(TYPICAL) SEE NOTE #3
AUON ST�ORY FLTX ISLA�D DTOAIL (ONP VITW)
***THIS DRAWINGS IS NOT TO SCALE.***
TRAFFIC GATE
HOUSING
OF TRAVEL
DIRECTION
OF TRAVEL
DIRECTION
THE WHITE SQUARE REPRESENTS THE OPEN SPACE IN THE BASE OF THE AUTO SENTRY
THROUGH WHICH THE CONDUITS MUST ENTER THE BASE.
8 ½”
24 ½”
SIDE DOOR CLEARANCE
IMPORTANT:Do NOT install canopy
posts or other obstruct ions in this door swing area.
TRAFFIC GATE
ARM OR BARRIER
1' -
5"
RFID TRUSS BASE FOOTPRINT
CLCL
6' - 2 ½”"3'- 9 ½”
6"
24”
Figure 4. Auto Sentry Flex Island Specifications
Auto Passport Installation GuidePage 4 Copyright © Innovative Control Systems, Inc.
System WiringAuto Passport® All-In-One Reader/Antenna Power Requirements
� Power for the Auto Passport reader/antenna is supplied by the Auto Sentry flex.
� The Auto Sentry flex has terminal blocks located inside the base for power termination.
Wire Gauge and Conduit SizeWhen planning the orientation of the wiring runs, follow the applicable ICS wiring diagrams and consider the layout of the components at the site. To determine conduit size needed, see the table below for more information.
Table 2: Number of Wires (THHN) in a Given Conduit Size
1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3
AWG 14 13 24 39 69 94 154 — —
AWG 12 10 18 29 51 70 114 164 —
AWG 10 6 11 18 32 44 73 104 160
AWG 8 3 5 9 16 22 36 51 79
AWG 6 1 2 6 11 15 26 37 57
AWG 4 1 1 4 7 9 16 22 35
AWG 3 1 1 3 6 8 13 19 29
AWG 2 1 1 3 5 7 11 16 25
AWG 1 1 1 1 3 5 8 12 18
Recommended and Accepted Grounding MethodsThe Auto Passport equipment must be properly grounded. Proper system grounding is an extremely important part of the system installation. Grounds for all devices should be wired to the main service electrical panel ground bus bar which, in turn, should be grounded to a ground rod. A conduit ground does not provide a sufficient ground. It is recommended that the neutral and ground bus bars be bonded together when it is not prohibited by local codes.
The universal ground symbol identifies the grounding terminal located in the Auto Sentry unit near the terminal blocks.
WAR�I�GE: Failure to properly ground the unit could result in unit failure and/or bodily injury. Ground wire must be connected to the ground terminals.
�NOTE: � Improper grounding will void equipment warranty.
Auto Passport Installation GuidePage 5 Copyright © Innovative Control Systems, Inc.
RFID Wiring LayoutThe wiring layout is the same for one, two, three, or four lanes. There is one cable that houses five wires and they connect from the RFID All-in-One Reader / Antenna back to its corresponding Auto Sentry flex. See Figure 6.
ICS SUPPLIED 35' CABLE
RFID WIRI�G ORIPLT LA�T LAYNUO
AUON ST�ORY FLTX
LANE #1 RFID READER / ANTENNA
LANE #3 RFID READER / ANTENNA
LANE #2 RFID READER / ANTENNA
THERE WILL BE THREE ALL-IN-ONE RFID READER/ANTENNAS WITH 35' LEADS THAT TERMINATE BACK TO THEIR OWN AUTO SENTRY FLEX. THERE WILL BE (3) 35' CABLES PROVIDED.
RFID WIRI�G PLA�TERMINATE THE CABLE FROM THE RFID ALL-IN-ONE RFID READER/ ANTENNA ENCLOSURE TO THE RIGHT-SIDE OF THE TERMINAL BLOCKS INSIDE THE AUTO SENTRY FLEX HEAD AS FOLLOWS:BLACK ALL I� N�T CABLT ALL (5) WIRES ARE LABELED: PNWTR WIRTS ATTACH WIRE MARKED 24V(+) TO THE ORANGE TERMINAL BLOCK (24+) ATTACH WIRE MARKED 24V(-) TO THE BLACK TERMINAL BLOCK (24-) DAOA WIRTS ATTACH WIRE MARKED TX TO THE ORANGE TERMINAL BLOCK (TX) ATTACH WIRE MARKED RX TO THE YELLOW TERMINAL BLOCK (RX) ATTACH WIRE MARKED GROUND TO THE WHITE TERMINAL BLOCK (GD)
Figure 6. Layout Triple Lane Example RFID Wiring Layout
AUON ST�ORY LA�T CN�DUIO DTOAIL
THIS DRAWING IS ONLY INTENDED TO SHOW THE CONDUIT REQUIREMENTS FOR THE AUTO SENTRY ISLANDS IN DETAIL.
THIS DRAWING IS NOT TO SCALE.
LANE #1 AUTO
SENTRY ISLAND
3/4" CONDUIT
LANE #2 AUTO
SENTRY ISLAND
1/2" CONDUIT STUBBED OUT TO CONNECT WITH
GATE CLOSING LOOP
1/2" CONDUIT STUBBED OUT TO CONNECT WITH GATE
CLOSING LOOP
1/2" CONDUIT STUBBED OUT TO CONNECT WITH THE MERGE LOOP. THE MERGE LOOP SHOULD BE RUN TO THE TRAFFIC GATE IN LANE #1.
1" CONDUIT TO SITE MAIN SERVICE
ELECTRICAL PANEL
�NOTE: ENSURE THAT ALL CONDUITS RUNNING TO THE GATES ARE TIGHTLY BUNDLED TOGETHER AS THE OPENING IN THE BASE OF THE GATE IS ONLY 3- ¼
INCHES IN DIAMETER.
LOW VOLTAGE CONDUIT
HIGH VOLTAGE CONDUIT
3/4" CONDUIT
RFID TRUSS BASE
1" CONDUITS
RFID TRUSS BASE
LANE #3 AUTO
SENTRY ISLAND
3/4" CONDUIT
1/2" CONDUIT STUBBED OUT TO CONNECT WITH GATE
CLOSING LOOP
1" CONDUIT
1/2" CONDUIT CONNECTING THE
TWO GATES
RFID TRUSS BASE
(9) - 1" CONDUITS:• THREE POWER CONDUITS GOING TO
THE POWER DISTRIBUTION BOX WHICH POWERS THE AUTO SENTRY.
• THREE POWER CONDUITS GOING BACK TO THE MAIN SERVICE ELECTRIC PANEL WHICH POWERS THE HEAT EXCHANGERS.
• THREE CONDUITS FOR LOW VOLTAGE GOING TO THE LOW VOTLAGE JUNCTION BOX.
½ CONDUIT STUB OUTS FOR CONNECTION TO LOOPS
Figure 5. Triple Lane Example Conduit Layout
Conduit Detail (Triple Lane)
Auto Passport Installation GuidePage 6 Copyright © Innovative Control Systems, Inc.
Truss and RFID System Installation�NOTE: � It is recommended to have 2 people perform the installation of the RFID system.
Tools Required (not supplied by ICS) � 1/8” Allen Wrench
� Small Flat Head Screw Driver
� Hammer Drill
� Diagonal Cutting Pliers
� Fish Tape
� Ladder
Parts Required (not supplied by ICS) � 8” or greater UV Cable Ties
� 1/2” dia. x 6” L Concrete Anchor Bolts
Parts Required (supplied by ICS)Part Description Parts Included
All-In-One RFID Reader / Antenna Enclosure
NOTE: Colors may vary.
Power and Data Wires
in the RFID All-In-One Cable
Estimated Completion TimeWe estimate that it will take 2 hours to perform this procedure. Keep all hardware organized as you work.
WAR�I�GE: Please have a certified electrician check voltages on the power supply before installing new components. Ohe voltage should be 24 volts.
Auto Passport Installation GuidePage 7 Copyright © Innovative Control Systems, Inc.
10 Amp Circuit Breaker in the left side of the head of the Auto Sentry flex
6 Amp Circuit Breaker
Instructions to Power Down the Auto Sentry flex WAR�I�GE: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death.
1. On the site server desktop, click on the VNC icon for the Auto Sentry flex.
2. On the menu bar, click the Windows flag icon.
3. Click the Shutdown button.
4. Wait until the Auto Sentry flex display goes to a white screen.
5. Open the rear doors of the Auto Sentry flex.
6. Inside the head of the Auto Sentry flex, turn off the power switch.
7. Inside the left side of the head of the Auto Sentry flex, turn off both Circuit Breakers by pressing the blue buttons on the breakers until they click out. See Figure 7.
8. Inside the base of the Auto Sentry flex, turn off the breaker by pressing the blue button on the breaker until it clicks out.
Figure 7. Circuit Breaker Location
9. Shut off the electricity by turning off the Auto Sentry flex breaker inside the ICS® power distribution box.
Auto Passport Installation GuidePage 8 Copyright © Innovative Control Systems, Inc.
TRUSS BASE LOCATION – SIDE VIEWTHIS DRAWING IS NOT TO SCALE
1' - 5”
TRAFFIC LANE GRADE
CLRFID
TRUSS
11”
AUTO SENTRY FLEX
CONCRETE ISLAND
RFID TRUSS
RFID TRUSS BASE
6"
NOTE: CONCRETE ISLAND MUST BE 6 INCHES ABOVE THE FINAL TRAFFIC LANE GRADE
6"
Truss Base Mounting Location � Mount truss base 1’5” from the edge of the curb to the center of the truss base. See Figure 8.
� Mount truss base 30 1/2” from the center of the Auto Sentry flex to the center of the truss. See Figure 9.
Figure 9. Truss Base Location Side View
AUTO SENTRY FINAL
TRAFFIC LANE
GRADE
RFID LANEFRONT VIEWTHIS DRAWING IS NOT TO SCALE
CLCL
AUTO SENTRY
9' -
2"
RFID ANTENNA ENCLOSURE
CONCRETE ISLAND CONCRETE ISLAND
8' -
5"
7' -
11" 8'
- 8"
7' -
11 5
/8"
CLCL RFID
TRUSS
45 ½” NOTE: CONCRETE ISLAND MUST BE 6 INCHES ABOVE THE FINAL TRAFFIC LANE GRADE
FINAL TRAFFIC
LANE GRADE
0' - 6" 0' - 6"
SIDE DOOR SWINGSEE NOTE #5
2' – ½”
IMPNROA�OE:Do NOT install canopy posts or otherobstructions in this door swing area.
30 ½”15"6"
24 ½”
Figure 8. Truss Base Location Rear View
Auto Passport Installation GuidePage 9 Copyright © Innovative Control Systems, Inc.
TRUSS-BASE DIMENSIONS
12"
6"
1" 1"
1"
5" 5"2
1/8"
12"
6"
1"2
1/2"
2 1/
2"
2" 2"
SEE NOTE #1
SEE NOTE #1
SEE NOTE #1
SEE NOTE #1
SEE NOTE #1
2 1/8" DIA. HOLE. SEE NOTE #2
NOTE #1: THE TRUSS-BASE MOUNTING HOLES. THEY ARE 9/16" IN DIAMETER. USE 1/2” DIA. X 6" L CONCRETE ANCHOR BOLTS THROUGH EACH OF THE FIVE MOUNTING HOLES TO SECURE THE BASE OF THE TRUSS TO THE CONCRETE ISLAND.
THE THREE MOUNTING HOLES THAT ARE ADJACENT TO THE REAR EDGE OF THE TRUSS BASE SHOULD ALWAYS BE FURTHEST AWAY FROM THE TRAFFIC LANE AND THE VEHICLE. THE TWO MOUNTING HOLES ADJACENT TO THE FRONT EDGE OF THE TRUSS BASE SHOULD ALWAYS BE CLOSEST TO THE TRAFFIC LANE AND THE VEHICLE.
NOTE #2: THE TRUSS-BASE CONDUIT HOLE. THIS IS THE HOLE IN THE TRUSS-BASE THROUGH WHICH THE CONDUIT CONTAINING THE ANTENNA CABLING WILL PASS. MINIMALLY, A 1" CONDUIT IS RECOMMENDED FOR THE ANTENNA CABLING.
FRONT EDGE OF TRUSS-BASE
REAR EDGE OF TRUSS-BASE
IN RELATIONSHIP TO TRUSS BASE
DIRECTION OF VEHICLE TRAVEL
Truss Base Mounting Instructions1. The three mounting holes that are adjacent to the rear edge of the truss base should always be furthermost away from
the traffic lane and the vehicle. The two mounting holes adjacent to the front edge of the truss base should always be closest to the traffic lane and the vehicle. See Figure 10.
2. The center hole in the truss-base is used to pass the RFID all-in-one reader/antenna cable to pass from the conduit up through the center of the truss to the RFID enclosure. Minimally, a 1” conduit is recommended for the RFID All-In-One Cable.
3. Using a hammer drill, secure the base of the truss to the concrete island with 1/2” dia. x 6”L concrete anchor bolts through each one of the mounting holes in the base of the truss. There are (5) truss-base mounting holes 9/16” in Diameter.
Figure 10. Truss Base Mounting Specifications
Auto Passport Installation GuidePage 10 Copyright © Innovative Control Systems, Inc.
7' –
11
5/8"
RFID ANTENNA
ENCLOSURE
CLCENTER LINE OF
RFID UNIT
4' – 7"
2' – 6"
5 3
/8"
TRAFFIC LANE GRADE
0' - 6"
3' – 6 1/2"
7' –
11"
8' –
5"
RFID LANE – SIDE VIEWTHIS DRAWING IS NOT TO SCALE
CONCRETE ISLAND
6' – 7"
8' –
8" 9' –
2"
NOTE: CONCRETE ISLAND MUST BE 6 INCHES ABOVE THE FINAL TRAFFIC LANE GRADE
Figure 11. RFID Reader/Antenna Enclosure on Truss
Figure 12. RFID Enclosure Mounting on Truss
RFID All-In-One Reader/Antenna Mounting1. Attach the RFID All-In-One Reader / Antenna enclosure to the truss that is next the Auto Sentry and extends over the lane.
� The truss will be shipped with truss brackets and hex screws. (1/8” Allen key is needed to install but not supplied by ICS).
2. Mount the center of the enclosure at 3’ 6-1/2” from the edge of the curb. See Figure 12.
� To ensure the proper angle for the antenna, the enclosure should be mounted so the top of the enclosure is level. The antenna is angled inside of the enclosure. The enclosure will appear to be facing down. See Figure 9, Figure 11, and Figure 12.
3. Route cable down through the center of the truss. ICS recommends securing the cable to the truss every 12 inches with cable ties.
4. Use diagonal cutters to cut excess length off of the cable ties.
IMPNROA�OE: The enclosure should not be rotated on the truss as that would move the antenna to a position where it is not designed to work properly.
Auto Passport Installation GuidePage 11 Copyright © Innovative Control Systems, Inc.
RFID All-In-One Reader/Antenna Wiring1. Unplug the cables from the bill dispenser.
2. Unbolt the bill dispenser from the bill dispenser tray.
3. Remove the bill dispenser.
4. Unscrew any cable clamps holding the bill dispenser cables to the drawer and remove the cables from the drawer.
5. Remove the bill dispenser drawer from the base of the Auto Sentry flex.
6. Using the fish tape, pull the RFID All-In-One Cable through the 1” conduit from the base of the truss to the Auto Sentry flex.
7. Locate the set of terminal blocks included on the left wall inside the base as shown in Figure 13.
�NOTE: � There is a terminal description label below the terminal blocks.
8. The RFID All-In-One RFID Reader/Antenna cable has 5 wires to connect to the terminal blocks as follows, see Figure 13 and Figure 14.
� Attach the power wires marked 24VDC(+) and 24VDC(-) from the RFID reader to the bottom terminals of the orange and black terminal blocks: 24V DC(+) wire to orange terminal block 24V DC(+), and the 24V DC(-) wire to black terminal block 24V DC(-).
� Attach the data wires from the RFID reader to the bottom terminals of the orange, yellow, and white terminal blocks: the wire marked (Tx) to the orange terminal block (Tx), the wire marked (Rx) to the yellow terminal block (Rx), and the wire marked Ground to the white terminal block (GD).
9. Re-install the bill dispenser drawer and the bill dispenser.
10. Re-attach the cables for the bill dispenser.
Figure 13. Terminal Block Inside Auto Sentry Base Figure 14. Wire Termination
Auto Passport Installation GuidePage 12 Copyright © Innovative Control Systems, Inc.
Instructions to Power On the Auto Sentry flex1. After the truss and enclosure are installed, and all the wires are connected as instructed on page 11, reconnect the power to the
ICS power distribution box by turning on the Auto Sentry flex breaker inside the ICS® power distribution box.
2. Turn the breakers on in the head and the base of the Auto Sentry flex by pressing the blue buttons on the breakers until they click in. See Figure 7 on page 7.
3. Inside the base of the Auto Sentry flex, turn on the breaker by pressing the blue button on the breaker until it clicks in.
4. Inside the Auto Sentry flex, turn on the power switch to boot the system.
5. Please contact ICS Technical Support to configure the RFID system: 800-246-3469
Corporate Office: 81 Highland Avenue, Suite 300, Bethlehem, PA 18017 | Sales: 800.642.9396 Email: [email protected] | icscarwashsystems.com
If you have any questions or concerns, please contact ICS Technical Support: 800-246-3469.