autodome ip 4000 hd/5000 hd/ir

AUTODOME IP 4000 HDNEZ-4112-PPCW4 │ NEZ-4212-PPCW4 │ NEZ-4112-CPCW4

en Installation Manual

AUTODOME IP 4000 HD Table of contents | en 3

Bosch Security Systems Installation Manual 2015.11 | 1.1 |

Table of contents1 Safety 51.1 About this Manual 51.2 Legal Information 51.3 Safety Precautions 51.4 Important Safety Instructions 61.5 Connection in Applications 71.6 Important Notices 71.7 Customer Support and Service 82 Introduction 102.1 Parts List 103 System Overview 114 Mounting Accessories 125 Installation Overview 135.1 Prepare Wiring 135.2 Prepare the Camera 136 Installing a microSD card (optional) 157 Installing an In-Ceiling Camera in a Drywall Ceiling 177.1 Tools Required 177.2 Installation Requirements 177.3 Preparing the Ceiling for Installation 177.4 Securing the Camera to the Ceiling 178 Installing an In-ceiling Camera in a Suspended Ceiling 208.1 Tools Required 208.2 Installation Requirements 208.3 Prepare Suspension Ceiling for Installation 208.4 Securing the Camera to the Ceiling 219 Installing a Surface Mount and Camera 249.1 Tools Required 249.2 Installation Requirements 249.3 Preparing the Surface Mount for Installation 249.4 Installing the Surface Mount Adapter 259.5 Installing the Camera to the Mounting Plate 2710 Installing a Wall Mount and Camera 3010.1 Parts List 3010.2 Tools Required 3010.3 Installation Requirements 3010.4 Preparing the Wall for Installation 3010.5 Preparing the Wall Mount for Installation 3110.6 Installing the Wall Mount 3210.7 Installing the Camera to the Mounting Plate 3311 Installing a Pipe Mount and Camera 3611.1 Parts List 3611.2 Tools Required 3611.3 Installation Requirements 3611.4 Preparing the Pipe Mount for Installation 3611.5 Installing the Pipe Mount 3611.6 Installing the Camera to the Mounting Plate 4112 Installing a Junction Box (VDA-AD-JNB) 44

4 en | Table of contents AUTODOME IP 4000 HD

2015.11 | 1.1 | Installation Manual Bosch Security Systems

12.1 Parts List 4412.2 Installation Requirements 4412.3 Preparing for Installation 4412.4 Installing the Junction Box (VDA-AD-JNB) 4513 Connection 4914 Troubleshooting 5115 Maintenance 5216 Decommissioning 5416.1 Transfer 5416.2 Disposal 5417 Technical data 55

AUTODOME IP 4000 HD Safety | en 5


1 Safety1.1 About this Manual

This manual has been compiled with great care and the information it contains has beenthoroughly verified. The text was complete and correct at the time of printing. Because of theongoing development of products, the content of the manual may change without notice.Bosch Security Systems accepts no liability for damage resulting directly or indirectly fromfaults, incompleteness, or discrepancies between the manual and the product described.

1.2 Legal InformationCopyrightThis manual is the intellectual property of Bosch Security Systems, Inc. and is protected bycopyright. All rights reserved.TrademarksAll hardware and software product names used in this document are likely to be registeredtrademarks and must be treated accordingly.

1.3 Safety PrecautionsIn this manual, the following symbols and notations are used to draw attention to specialsituations:

Danger!High risk: This symbol indicates an imminently hazardous situation such as “DangerousVoltage” inside the product. If not avoided, this will result in an electrical shock, seriousbodily injury, or death.

!

Warning!Medium risk: Indicates a potentially hazardous situation. If not avoided, this may result inminor or moderate injury.

!

Caution!Low risk: Indicates a potentially hazardous situation. If not avoided, this may result inproperty damage or risk of damage to the unit.

Notice!This symbol indicates information or a company policy that relates directly or indirectly to thesafety of personnel or protection of property.

6 en | Safety AUTODOME IP 4000 HD


1.4 Important Safety InstructionsRead, follow, and retain for future reference all of the following safety instructions. Follow allwarnings before operating the device.1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners.2. Do not install device near any heat sources such as radiators, heaters, stoves, or other

equipment (including amplifiers) that produce heat.3. Never spill liquid of any kind on the device.4. Take precautions to protect the device from power and lightning surges.5. Adjust only those controls specified in the operating instructions.6. Operate the device only from the type of power source indicated on the label.7. Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing

to qualified service personnel.8. Install in accordance with the manufacturer's instructions in accordance with applicable

local codes.9. Use only attachments/accessories specified by the manufacturer.10. Protect all connection cables from possible damage, particularly at connection points.

!

Caution!Installation must be made by qualified personnel and conform to ANSI/NFPA 70 (the NationalElectrical Code® (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1),and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for anydamages or losses caused by incorrect or improper installation.

!

Warning!Bosch’s version of High PoE:If supplying power to the camera by HPoE or a midspan device, you must install additionalsurge protection.

All-pole power switch - Incorporate an all-pole power switch, with a contact separation of atleast 3 mm, into the electrical installation of the building. If it is needed to open the housing,use this all-pole switch as the main disconnect device for switching off the voltage to the unit.Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140feet, in accordance with NEC800 (CEC Section 60).Fuse rating - For security protection of the device, the branch circuit protection must besecured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CECSection 60).Ventilation – Any openings in the device / enclosure are provided for ventilation to preventoverheating and to ensure reliable operation. Do not block or cover these openings. Do notplace the device in an enclosure unless proper ventilation is provided, or the manufacturer’sinstructions have been adhered to.Outdoor signals - The installation for outdoor signals, especially regarding clearance frompower and lightning conductors and transient protection, must be in accordance with NEC725and NEC800 (CEC Rule 16-224 and CEC Section 60).Power disconnect - Units have power supplied whenever the power cord is inserted into thepower source, or when High Power-over-Ethernet (High PoE) power is provided over theEthernet CAT 5E/6 cable. The power cord is the main power disconnect device for switchingoff the voltage for all units. When High PoE or PoE+ (820.3at) is used to power the unit, thepower is provided over the Ethernet cable, which is then the main power disconnect devicefor switching off the voltage for all units.



Video loss - Video loss is inherent to digital video recording; therefore, Bosch SecuritySystems cannot be held liable for any damage that results from missing video information.To minimize the risk of losing information, we recommend multiple, redundant recordingsystems, and a procedure to back up all analog and digital information.

!

Caution!Always securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allowwater to enter the housing and damage the units. If a sealant is used, ensure that it is aneutral cure type. Sealants that release acetic acid may harm electronics. Use drip loops onthe wiring outside the housing.

Always use Teflon tape and sealant on connector threads of any mount (sold separately byBosch or user-supplied).

1.5 Connection in Applications24 VAC power source: This unit is intended to operate with a limited power source. The unitis intended to operate at 24 VAC (if PoE+ is not available). User supplied wiring must be incompliance with electrical codes (Class 2 power levels).PoE: Use only approved PoE+ devices. Power-over-Ethernet can be connected at the sametime as a 24 VAC power supply.If auxiliary power (24 VAC) and PoE+ are applied simultaneously, the camera selects auxiliaryinput and shuts off PoE+.For pendant models used in outdoor applications that require heaters, a Bosch High PoE 60Wmidspan (NPD-6001A, sold separately) is required to power both the camera and its internalheaters.For in-ceiling or indoor pendant applications that don’t require heater power, standard PoE+(802.3at) midspans or switches can be used to power the camera.

1.6 Important NoticesIndoor use only - The product shall only be used indoors. Ethernet network should beconnected to a network environment, which must comply with the following conditions:1.1 The function of the ITE being investigated to IEC 60950-1 is considered not likely torequire connection to an Ethernet network with outside plant routing, including a campusenvironment.1.2 The ITE is to be connected only to PoE networks without routing to the outside plant.

Notice!This device is intended for use in public areas only.U.S. federal law strictly prohibits surreptitious recording of oral communications.

UL DisclaimerUnderwriter Laboratories Inc. ("UL") has not tested the performance or reliability of thesecurity or signaling aspects of this product. UL has only tested fire, shock and/or casualtyhazards as outlined in Standard(s) for Safety for Information Technology Equipment, UL60950-1 . UL Certification does not cover the performance or reliability of the security orsignaling aspects of this product.UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVERREGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATEDFUNCTIONS OF THIS PRODUCT.

8 en | Safety AUTODOME IP 4000 HD


Notice!This is a class B product. In a domestic environment, this product may cause radiointerference, in which case the user may be required to take adequate measures.

FCC & ICES Information(U.S.A. and Canadian Models Only)This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limitsare designed to provide reasonable protection against harmful interference when theequipment is operated in a residential installation. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance with theinstruction manual, may cause harmful interference to radio communications. However, thereis no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference byone or more of the following measures:– Reorient or relocate the receiving antenna;– Increase the separation between the equipment and the receiver;– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected;– Consult the dealer or an experienced radio/TV technician for help.Intentional or unintentional modifications, not expressly approved by the party responsible forcompliance, shall not be made. Any such modifications could void the user's authority tooperate the equipment. If necessary, the user should consult the dealer or an experiencedradio/television technician for corrective action.The user may find the following booklet, prepared by the Federal CommunicationsCommission, helpful: How to Identify and Resolve Radio-TV Interference Problems. Thisbooklet is available from the U.S. Government Printing Office, Washington, DC 20402, StockNo. 004-000-00345-4.

1.7 Customer Support and ServiceIf this unit needs service, contact the nearest Bosch Security Systems Service Center forauthorization to return and shipping instructions.Service CentersUSATelephone: 800-366-2283 or 585-340-4162Fax: 800-366-1329Email: [email protected] ServiceTelephone: 888-289-0096Fax: 585-223-9180Email: [email protected] SupportTelephone: 800-326-1450Fax: 585-223-3508 or 717-735-6560Email: [email protected] CenterTelephone: 585-421-4220Fax: 585-223-9180 or 717-735-6561



Email: [email protected]: 514-738-2434Fax: 514-738-8480Europe, Middle East & Africa RegionPlease contact your local distributor or Bosch sales office. Use this link:http://www.boschsecurity.com/startpage/html/europe.htmAsia Pacific RegionPlease contact your local distributor or Bosch sales office. Use this link:http://www.boschsecurity.com/startpage/html/asia_pacific.htm

More InformationFor more information please contact the nearest Bosch Security Systems location or visitwww.boschsecurity.com

10 en | Introduction AUTODOME IP 4000 HD


2 Introduction– This equipment should be unpacked and handled with care. Check the exterior of the

packaging for visible damage. If an item appears to have been damaged in shipment,notify the shipper immediately.

– Verify that all the parts listed in the Parts List below are included. If any items aremissing, notify your Bosch Security Systems Sales or Customer Service Representative.

– Do not use this product if any component appears to be damaged. Please contact BoschSecurity Systems in the event of damaged goods.

– The original packing carton is the safest container in which to transport the unit and mustbe used if returning the unit for service. Save it for possible future use.

2.1 Parts List

1 AUTODOME IP 4000 HD camera

1 Camera mounting plate (pendant models only)

1 Mounting template (in-ceiling model only)

1 Screwdriver, T10 Torx

1 Screwdriver, T15 Torx

4 MAC address labels

1 Quick Installation Guide

AUTODOME IP 4000 HD System Overview | en 11


3 System OverviewThe AUTODOME IP 4000 HD is a compact, indoor PTZ dome camera with a high-resolution720p25/30 (1MP) or 1080p25/30 (2MP) HD sensor and a powerful 12x optical zoom thatallows operators to monitor wide scenes without losing any details. The camera’s aestheticdesign and flexible mounting options allow unobtrusive surveillance of large halls, receptionareas, or waiting areas that would otherwise require multiple cameras for effectivesurveillance.When a connection is established, the Live page is initially displayed. The application bardisplays the following items:

– Live,

– Playback,This link is only visible if a storage medium has been configured for recording. (With VRMrecording this option is not active.)

– Configuration.

Getting help

To get context sensitive help for a particular page, click the help icon .

12 en | Mounting Accessories AUTODOME IP 4000 HD


4 Mounting AccessoriesThe following mounting accessories are available (and are supplied with separate mountinginstructions) for AUTODOME IP 4000 HD cameras.

Model Number Description Application

NEZ-A4-WW Wall mount kit Indoor/outdoor vertical walls

NEZ-A4-PW Pipe mount kit Indoor/outdoor high ceilings

NEZ-A4-SMB Surface mount kit Indoor hard-ceiling

AUTODOME IP 4000 HD Installation Overview | en 13


5 Installation Overview

!

Caution!Installation must be made by qualified personnel and conform to ANSI/NFPA 70 (the NationalElectrical Code® (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1),and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for anydamages or losses caused by incorrect or improper installation.

1. Select the mounting location.Select a secure installation location and mounting position for the device. Ideally, this is alocation where the device cannot be interfered with either intentionally or accidentally.4 Ensure that the selected mounting surface is capable of supporting the combined weight

of the camera and mounting hardware (sold separately) under all expected conditions ofload, vibration, and temperature.

5.1 Prepare Wiring4 Prepare and install all wiring for 24 VAC, PoE+ (Cat5e/Cat6), alarms, and audio as

necessary. For 24 VAC, follow the recommendations for maximum cable distance andwire gage.

Maximum cable distance in meters (feet) per minimum cable diameterThe following table identifies the recommended transmission distance (maximum) in meters(feet), based on the specified wattage, per the minimum cable diameter (in mm²), when thecable diameter is fixed and the maximum permitted power consumption for 24 VAC is 10%.For example, for a device of 20 W and a minimum cable diameter of 1.0 mm², therecommended transmission distance is 42 m (141 feet) from the transformer.

Models Watts 1.0 mm² 1.5 mm² 2.5 mm² 4.0 mm²

Indoor(ceiling)

20 42 m (141 ft) 68 m (225 ft) 109 m (358 ft) 275 m (905 ft)

Outdoor 30 28 m (94 ft) 45 m (150 ft) 72 m (238 ft) 183 m (603 ft)

Wire GageNote: Metric wire sizes are standard DIN sizes, ISO6722, mm².

Wire diameter (mm²) AWG

1.0 18

1.5 16

2.5 14

4.0 12

5.2 Prepare the Camera1. Loosen the three (3) Hex screws in the trim ring / bubble enclosure with the T15 Torx

screwdriver.

14 en | Installation Overview AUTODOME IP 4000 HD


1 2

3

Figure 5.1: Loosen enclosure screws (pendant models)

2. Remove the trim ring / bubble enclosure.

Figure 5.2: Remove trim ring and bubble (pendant models)

Note: The next two steps are for the in-ceiling model only.1. Remove the foam insert that protects the camera block.2. Remove the tape holding the plastic lens protector; remove the lens protector.

1

2

3

Figure 5.3: Remove trim ring/bubble, packing (in-ceiling model)

AUTODOME IP 4000 HD Installing a microSD card (optional) | en 15


6 Installing a microSD card (optional)1. Push the camera block until you see the card slot (item 1 in the following figure).2. Insert the card into the slot (item 2 in the following figure).3. Push the camera block into its original position (item 3 in the following figure).

microSD Card

1

2 3

Figure 6.1: Insert SD card (in-ceiling model)

1

2 3

microSD Card

Figure 6.2: Insert SD card (pendant models)

Note: The next two steps are for pendant models only.1. Replace the trim ring / bubble enclosure.2. Tighten the screws with the T15 Torx screwdriver.

16 en | Installing a microSD card (optional) AUTODOME IP 4000 HD


Figure 6.3: Replace trim ring/bubble (pendant models)

1 2

3

Figure 6.4: Tighten screws (pendant models)

3. Proceed with installation.

AUTODOME IP 4000 HD Installing an In-Ceiling Camera in a Drywall Ceiling | en 17


7 Installing an In-Ceiling Camera in a Drywall Ceiling7.1 Tools Required

– Appropriate straight slot screwdriver– Appropriate tool for cutting a hole in drywall or ceiling tile (if applicable)

7.2 Installation Requirements– The ceiling thickness ranges from 10 - 40 mm.– The ceiling can sustain at least eight (8) times the weight of the camera (1.81 kg (4 lb)): >

14.5 kg (32 lb).

7.3 Preparing the Ceiling for Installation1. Use the template to mark the hole in the ceiling for the camera.

> 15 kg

(33 lb)

Figure 7.1: Mark hole with Template

2. Cut the hole in the ceiling with a drywall utility saw or jig saw.

160 mm

(6.3 in.)

Figure 7.2: Cut hole in ceiling

3. Pull the cables (24 VAC, CAT 5/CAT6, alarm and/or audio as needed) through the hole inthe ceiling.

Figure 7.3: Cables from ceiling

7.4 Securing the Camera to the Ceiling1. Connect the cables from the ceiling to the cables on the camera. Refer to the chapter

Connection for more information.

18 en | Installing an In-Ceiling Camera in a Drywall Ceiling AUTODOME IP 4000 HD


24VA

C

RJ45

24V

AC

Figure 7.4: Connect cables to camera

2. Insert the camera (without the trim ring / bubble enclosure) into the hole in the ceiling.Ensure not to pinch the cables.

Figure 7.5: Insert camera into hole

3. Turn each fastening screw (item 1 in the following figure) to secure the clamps in theceiling.

4. Tighten the clamps using the T10 Torx screwdriver to secure the housing to the ceiling.

!

Warning!Over torquing the ceiling clamps can damage the clamp or ceiling. Only tighten the clampuntil it contacts the ceiling and you start to feel some resistance. If using a powerscrewdriver, set the torque level to the lowest setting.

Figure 7.6: Secure clamps to ceiling

5. Place the trim ring / bubble enclosure in position over the camera block, aligning thethree (3) screws (item 1 in the following figure). Tighten the screws firmly to secure thetrim ring / bubble enclosure to the in-ceiling bracket.

6. Remove the protective plastic sheet from the bubble. Installation is complete.

AUTODOME IP 4000 HD Installing an In-Ceiling Camera in a Drywall Ceiling | en 19


Figure 7.7: Camera installed in ceiling

20 en | Installing an In-ceiling Camera in a Suspended Ceiling AUTODOME IP 4000 HD


8 Installing an In-ceiling Camera in a Suspended Ceiling8.1 Tools Required

– Appropriate straight slot screwdriver– Appropriate tool for cutting a hole in drywall or ceiling tile (if applicable)

8.2 Installation Requirements– The ceiling thickness ranges from 10 - 40 mm.– The ceiling can sustain at least eight (8) times the weight of the camera (1.81 kg (4 lb)): >

14.5 kg (32 lb).

8.3 Prepare Suspension Ceiling for InstallationYou must use the VGA-IC-SP In-ceiling Support Kit to install the camera In-ceiling housing intoa suspended or drop ceiling. This kit requires a separate purchase.1. Choose the desired location to mount the camera.2. Remove an adjacent ceiling tile.3. Loosen the four (4) securing screws, located in the corners of the Bracket Assembly,

enough to hold the suspension bars but still allowing adjustment during installation.4. Place the Bracket Assembly over the ceiling tile, which is used to mount the camera.5. Snap the Bar Clips of the bracket to the ceiling rails.

A

Figure 8.1: Suspension Ceiling Bracket (Top View)

1 Suspension Bars 3 Securing Screw (4)

2 Base Plate 4 Bar Clips

1. Use the bracket Base Plate as a template or cut a hole-sized hole in the center of theceiling tile with a drywall utility saw or jig saw.

AUTODOME IP 4000 HD Installing an In-ceiling Camera in a Suspended Ceiling | en 21


Figure 8.2: Cut Hole in Ceiling Tile

2. Tighten the four (4) securing screws to the Bracket Assembly.

Figure 8.3: Tighten Bracket Securing Screw

3. Secure the Bracket Assembly to an overhead securing point with a safety wire.

Figure 8.4: Secure Bracket Assembly

8.4 Securing the Camera to the Ceiling1. Connect the cables from the ceiling to the cables on the camera. Refer to the chapter

Connection for more information.

22 en | Installing an In-ceiling Camera in a Suspended Ceiling AUTODOME IP 4000 HD


24VA

C

RJ45

24V

AC

Figure 8.5: Connect cables to camera

2. Insert the camera (without the trim ring / bubble enclosure) into the hole in the ceiling.Ensure not to pinch the cables.

Figure 8.6: Insert camera into hole

3. Turn each fastening screw (item 1 in the following figure) to secure the clamps in theceiling.

4. Tighten the clamps using the T10 Torx screwdriver to secure the housing to the ceiling.

!

Warning!Over torquing the ceiling clamps can damage the clamp or ceiling. Only tighten the clampuntil it contacts the ceiling and you start to feel some resistance. If using a powerscrewdriver, set the torque level to the lowest setting.

Figure 8.7: Secure clamps to ceiling

5. Place the trim ring / bubble enclosure in position over the camera block, aligning thethree (3) screws (item 1 in the following figure). Tighten the screws firmly to secure thetrim ring / bubble enclosure to the in-ceiling bracket.


AUTODOME IP 4000 HD Installing an In-ceiling Camera in a Suspended Ceiling | en 23


Figure 8.8: Camera installed in ceiling

24 en | Installing a Surface Mount and Camera AUTODOME IP 4000 HD


9 Installing a Surface Mount and Camera9.1 Tools Required

– Appropriate straight slot screwdriver– Appropriate tool for cutting a hole in drywall or ceiling tile (if applicable)– One (1) ground– One #10 screw to attach the ground lug

9.2 Installation Requirements– The ceiling is thick enough to install the mounting screws.– The ceiling can sustain at least eight (8) times the weight of the camera (1.88 kg (4.14

lb)): > 15 kg (33 lb).

9.3 Preparing the Surface Mount for Installation1. Determine the side of the surface mount adapter (NEZ-A4-SMB) from which the external

cables are to be routed. Remove the plug from the appropriate hole in the side of theadapter (item a in the following figure).

2. Attach a ground wire (user-supplied) to the stand-off on the inside of the adapter withthe ground symbol (item b in the following figure) with a #10 screw (user-supplied).

3. Attach the flat, round end of the safety tether (supplied with the camera) to the stand-offon the inside of the adapter (item c in the following figure) with the #10 screw(supplied).

a

b

#10

c

#10

NEZ-A4-SMB

Figure 9.1: Prepare the surface mount adapter

AUTODOME IP 4000 HD Installing a Surface Mount and Camera | en 25


9.4 Installing the Surface Mount Adapter1. Determine a secure location for mounting the surface mount adapter (NEZ-A4-SMB) and

the camera.2. Use the adapter as a template to mark the installation location for four (4) M4 or #10 pan

head screws (with a minimum length of 10 mm (0.39 in.)) (user-supplied).3. Drill the four (4) holes in the installation location.4. Attach the surface mount adapter to the surface using the four screws.

x4 T5Figure 9.2: Mount with 4 screws

5. Attach conduit to the side of the adapter from which you removed the plug (the side fromwhich the external cables are to be routed).

6. Route the external cables (24 VAC, CAT 5/CAT6, alarm and/or audio as needed) throughthe conduit and into the surface mount adapter.

RJ45

24 VAC

Earth

Figure 9.3: Attach conduit, route cables

7. Attach the mounting plate (supplied with the camera) to the surface mount adapter withthe three (3) M4 – .7 x 8 Phillips pan head machine screws (supplied with the surfacemount adapter).



NEZ-A4-SMB

3x M4Figure 9.4: Attach mounting plate to SMB



Figure 9.5: Indicator for correct point of connection

9.5 Installing the Camera to the Mounting Plate1. Route the cables from the ceiling out of the side of the mounting plate with the crescent-

shaped cut-out.2. Attach the hook of the safety tether from the adapter to the bottom of the camera.3. Connect ground wire from the ground lug on the adapter to the center terminal on the 3-

pin terminal block for 24 VAC at the bottom of the camera.4. Connect the mating connectors from the user-supplied cables from the ceiling to the

matching connectors from the camera. Refer to the chapter Connection, page 49 formore information.



RJ45

b

c

d

a

EARTHAC24V

AC24V

Figure 9.6: Cable connections, safety tether

5. Unlock the single safety locking screw on the base of the unit using the T10 Torxscrewdriver (item 2 in the following figure).

6. Attach the camera to the mounting plate by inserting the vertical tab on the plate into therecessed slot on the top of the camera dome to the right of the safety locking screw.

Notice!Do not loosen the three brass buttons. These brass buttons engage the slotted tabs (item 5)on the mounting plate.

7. Rotate the camera approximately 15 degrees in a clockwise direction to lock firmly intoplace (item 1 in the following figure).

8. Secure the safety locking screw with the T15 Torx screwdriver (item 2 in the followingfigure).



a

b

≈ 15°

Figure 9.7: Camera to mounting plate


30 en | Installing a Wall Mount and Camera AUTODOME IP 4000 HD


10 Installing a Wall Mount and Camera10.1 Parts List

The Wall Mount (NEZ-A4-WW) includes the following parts:

Quantity Item

1 Wall mount

1 Dome mounting cap

3 Screws, M4

1 Screw, #10

1 Installation Manual

10.2 Tools Required– Appropriate tool for cutting a hole in drywall– No. 2 Phillips screwdriver– Screwdriver, T-10 Torx

10.3 Installation Requirements– The wall is thick enough to install the mounting screws.– The wall can sustain at least eight (8) times the weight of the camera (1.88 kg (4.14 lb)):

> 15 kg (33 lb).

10.4 Preparing the Wall for Installation4 Determine a secure location for the wall mount (supplied separately).

1. Fit a metal, single-gang junction box (user-supplied) to the wall.2. Attach a grounded metal conduit to the junction box clamp.

< 11.33 kg

(25 lb)

Figure 10.1: Install junction box

AUTODOME IP 4000 HD Installing a Wall Mount and Camera | en 31


3. Route the external cables (24 VAC, CAT 5/CAT6, alarm and/or audio as needed) throughthe hole in the junction box.

Figure 10.2: Route cables through junction box

4. Route all cables from the junction box through the arm of the wall mount.

10.5 Preparing the Wall Mount for Installation1. Attach a ground lug (user-supplied) to the stand-off on the inside of the mounting cap

with the ground symbol inside of a circle (item 1 in the following figure) with a #10 screw(user-supplied).

2. Attach the round end of the safety tether (supplied with the camera) to the stand-off onthe inside of the mount with the ground symbol that is not inside of a circle (item 2 in thefollowing figure) with the #10 screw (supplied).

1 2

Figure 10.3: Prepare attachments



10.6 Installing the Wall Mount1. Attach the mounting cap to the arm of the wall mount.

Figure 10.4: Cap to Wall Mount

2. Attach the arm to the junction box with appropriate SEMS screws (user-supplied) thathave an integral lock washer to dig through the paint. Ensure an electrical groundconnection to the arm housing or ground lug.

x4

Figure 10.5: Attach arm to junction box

3. Attach the mounting plate (supplied with the camera) to the wall mount with the three(3) M4 screws supplied with the wall mount.



NEZ-A4-WW

Figure 10.6: Attach mounting plate to wall mount


shaped cut-out.2. Attach the hook of the safety tether from the adapter to the bottom of the camera.

NEZ-A4-WW

NEZ-4x12-PPCW4

Figure 10.7: Attach safety tether from wall mount to camera

3. Connect ground wire from the ground lug on the adapter to the center terminal on the 3-pin terminal block for 24 VAC at the bottom of the camera.



Ground wire1. Connect the mating connectors from the cables from the junction box to the matching

connectors from the camera. Refer to the chapter Connection for more information.

NEZ-4x12-PPCW4

RJ45

Figure 10.8: Cable connections








≈ 15°

1

2


6. Confirm that the housing is electrically grounded.7. Remove the protective plastic sheet from the bubble. Installation is complete.

Figure 10.10: Camera installed on wall mount

36 en | Installing a Pipe Mount and Camera AUTODOME IP 4000 HD


11 Installing a Pipe Mount and Camera11.1 Parts List

The Pipe Mount (NEZ-A4-PW) includes the following parts:

Quantity Item

1 Pipe Mount Base

1 Dome mounting cap

1 300 mm (11.8 in.) Pipe Extension

1 200 mm (7.9 in.) Pipe Extension

1 Pipe extension coupler

1 Ceiling flange

3 Screws, M4

1 Screw, #10


11.2 Tools Required– Appropriate tool for cutting a hole in drywall– No. 2 Phillips screwdriver– Screwdriver, T-10 Torx

11.3 Installation Requirements– The ceiling is thick enough to install the mounting screws.– The ceiling can sustain at least eight (8) times the weight of the camera (1.88 kg (4.14

lb)): > 15 kg (33 lb).

11.4 Preparing the Pipe Mount for Installation1. Attach a ground lug (user-supplied) to the stand-off on the inside of the mounting cap

with the ground symbol inside of a circle with a #10 screw (user-supplied).2. Attach the round end of the safety tether (supplied with the camera) to the stand-off on

the inside of the mount with the ground symbol that is not inside of a circle with the #10screw (supplied).

11.5 Installing the Pipe Mount1. Determine a secure location for the pipe mount. Ensure there is an adequate opening in

the ceiling or mounting structure for the cables to pass through.

AUTODOME IP 4000 HD Installing a Pipe Mount and Camera | en 37


751.9

(29.6)

444.9

(17.5)

88.8(3.5)

88.8(3.5)

Ø11.2 (4x)

(0.44)

3/4-14 NP

SM Threads

Ø153.0

544.9

(21.5)

Figure 11.1: Pipe Mount Dimensions

1. Use the four (4) holes in the flange as a template to mark the position where the holesshould be drilled to secure the mount.

Figure 11.2: Mark Flange Holes

2. Drill the four (4) holes in the installation location, screws not supplied, use a minimumscrew length of 10 mm (.39 in.).

!

Caution!All wires for installation applications must be routed through a grounded conduit.

3. Drill a fifth hole (maximum of 20 mm [.79 in.]) in the center of the four-hole pattern usedto mount the flange. Use this hole to feed the wires through the mount.

4 Fit the flange (supplied) to the pipe.

4 Select the pipe length of 200 mm (7.9 in.), 300 mm (11.8 in.), or combine the two (2)pipes with the integral coupler for 505 mm (20 in.).

4 Fit the dome cap to the bottom of the pipe.



Figure 11.3: Dome cap and pipe mount

4 Secure the flange using four (4) appropriate user-provided fasteners such as Moly orToggle bolts.

Notice!The fasteners and mounting surface must be capable of supporting a maximum load of 11.33kg (25 pounds).

4 Pull the wires from the pipe, starting at the flange end.



Figure 11.4: Attach Pendant Pipe Mount to Ceiling

!

Caution!Select a rigid mounting location to prevent excessive vibration to the camera.

4 Attach user supplied ground lug.

4 Align holes of mounting plate (supplied with dome) with dome mounting cap and attachwith the three (3) screws supplied.



Figure 11.5: Attach Mounting Plate to Dome Cap

1 Crescent Shape

2 Ground Lug

3 Dome Cap

4 Mounting Plate




shaped cut-out.2. Attach the hook of the safety tether from the adapter to the bottom of the camera.

NEZ-A4-PW

NEZ-4x12-PPCW4

RJ45

Figure 11.6: Safety tether

3. Connect ground wire from the ground lug on the adapter to the center terminal on the 3-pin terminal block for 24 VAC at the bottom of the camera.

Ground wire1. Connect the mating connectors from the user-supplied cables from the ceiling to the

matching connectors from the camera. Refer to the chapter Connection, page 49 formore information.



NEZ-4x12-PPCW4

RJ45

Figure 11.7: Connect cables








≈ 15°

1

2


6. Confirm that the housing is electrically grounded.7. Remove the protective plastic sheet from the bubble. Installation is complete.

Figure 11.9: Camera installed on pipe mount

44 en | Installing a Junction Box (VDA-AD-JNB) AUTODOME IP 4000 HD


12 Installing a Junction Box (VDA-AD-JNB)12.1 Parts List

The junction box (VDA-AD-JNB) includes the following parts:

Quantity Item

1 Junction box

1 Torx screwdriver

4 Screws, M4 (for the innermost set of holes on the front cover)

4 Screws and washers, M6 (to mount the box to a wall)

4 Screws and washers, M8 (for the middle set of holes on the front cover)

4 Screws, M10 (for the middle set of holes on the back cover)

1 3/4 x 260 in. Roll Teflon Tape

1 5g Container Silicon Grease


12.2 Installation Requirements– The wall is thick enough to install the mounting screws.

12.3 Preparing for Installation4 Determine a secure location for the junction box. Ensure there is an adequate opening in

the mounting surface for the cables to pass through.4 Loosen the front cover screws with the supplied Torx screwdriver.

1

2

3

4 M25

M25

G 3/4

G 3/4

Figure 12.1: Loosen front cover screws

4 To mount the junction box directly to a wall, use the outermost set of holes on the backof the junction box as a template to mark the location on the wall to drill holes for thefour mounting screws (supplied).

4 Drill the holes.

AUTODOME IP 4000 HD Installing a Junction Box (VDA-AD-JNB) | en 45


Note: The option to mount the junction box directly to a wall is valid only if you plan to installthe camera to a wall mount bracket. You cannot use this option with a corner mount bracketor a pole mount bracket because those two brackets attach to the back of the junction boxinstead of to the front.

12.4 Installing the Junction Box (VDA-AD-JNB)4 If desired, secure the junction box to the wall with the four M6 screws and washers.

x4 M6

+ x4 M6

> 80 mm

Ø

≤12 m

m

4x

Figure 12.2: Mount junction box to wall

4 Select one of the cable entry holes (drilled into two sides of the box) through which toroute the connection cables. (Refer to the first figure for hole sizes.)

4 Remove the plug from that hole only.

4 Route all connection cables (24 VAC, CAT 5/CAT6, alarm and/or audio as needed) throughthe side cable entry hole (item a in the following figure).

4 Route all connection cables (24 VAC, CAT 5/CAT6, alarm and/or audio as needed) throughthe cable entry hole in the front cover of the junction box (item b in the following figure).



4 If desired, use the cable management points in the bottom of the inside of the junctionbox to consolidate the cables.

– Remove one of the cable management clamps (items c and d in the following figure).– Tuck the cables into the cable management space (item e in the following figure).– Screw the clamp into place again (item f in the following figure).

ab

c

d

RJ45

24 VAC

Earth

e

f

Figure 12.3: Route cables through junction box

AUTODOME IP 4000 HD Installing a Junction Box (VDA-AD-JNB) | en 47


4 To mount a VEZ-A5-WMB wall mount bracket onto the junction box, insert the four (4) M8mounting screws through the holes in the arm of the wall mount bracket into the middleset of holes on the front cover of the junction box.

VEZ-A5-WMB

Work with wall mount bracket (1)

x4 M8 +

VEZ-A5-WMB

M25

M25

G 3/4

G 3/4

Figure 12.4: Junction box front cover - holes to mount wall mount bracket VEZ-A5-WMB

4 To mount a NEZ-A4-WW wall mount bracket onto the junction box, insert the four (4) M4mounting screws through the holes in the arm of the wall mount bracket into theinnermost set of holes on the front cover of the junction box.

Work with wall mount bracket (2)

NEZ-A4-WW

x4 M4

NEZ-A4-WW

M25

M25

G 3/4

G 3/4

Figure 12.5: Junction box front cover - holes to mount wall mount bracket NEZ-A4-WW



4 To mount a VGA-A-9542 corner mount bracket onto the junction box, insert the four (4)M10 mounting screws through the inner set of holes in the center section of the cornermount bracket into the middle set of holes on the back cover of the junction box.

Work with corner mount bracket (1)

M25

M25

G 3/4

G 3/4

x4 M10

VG4-A-9542

M25 G 3/4

VG4-A-9542

Figure 12.6: Junction box back cover - holes to mount corner mount bracket VGA-4-9542

4 To mount a VGA-A-9541 pole mount bracket onto the junction box, insert the four (4) M10mounting screws through the outer set of holes in the pole mount bracket into the middleset of holes on the back cover of the junction box.

Work with pole mount bracket (1)

VG4-A-9541

x4 M10

M25 G 3/4

VG4-A-9541

Figure 12.7: Junction box back cover - holes to mount pole mount bracket VGA-4-9541

AUTODOME IP 4000 HD Connection | en 49


13 Connection

!

Warning!Bosch’s version of PoE+If supplying power to the camera by PoE+ or by a midspan device, you must install additionalsurge protection.

!

Warning!Bosch’s version of High PoE:If supplying power to the camera by HPoE or a midspan device, you must install additionalsurge protection.

!

Caution!Compliance with EN50130-4 Alarm Standard – CCTV for Security ApplicationsTo meet the requirements of the EN50130-4 Alarm Standard, an ancillary uninterruptablepower (UPS) supply is necessary. The UPS must have a Transfer Time between 2–6 ms and aBackup Runtime of greater than 5 seconds for the power level as specified on the productdatasheet.

Note: Consult the National Electrical Code (NEC) for cable bundling requirements andlimitations.4 Connect the cable to the 24 VAC wires from the camera.

Label ID Description Cable Wire Color

AC24V 24 VAC Red

AC24V 24 VAC Black

EARTH Earth Ground Yellow/Green

4 Connect the Ethernet cable to the RJ45 connector of the camera. The following figureillustrates a typical system configuration.

1

2

3 41

2

2

4

Figure 13.1: AUTODOME IP System Config

1 AUTODOME camera

50 en | Connection AUTODOME IP 4000 HD


2 IP connection (Ethernet/CAT5/CAT6) (100 m maximum)

3 Network switch

4 Network device (computer with monitor, DVR/NVR, etc.)

4 If desired, connect the alarm and/or audio wires as identified in the following table.

Label ID Description Cable Wire Color

ALARM_COM Alarm Communications Red

ALARM_OUT Alarm Out Brown

ALARM_IN1 Alarm In 1 White

ALARM_IN2 Alarm In 2 Blue

AUDIO OUT Audio Out Grey

GND Ground Black

AUDIO GND Audio Ground Green

AUDIO IN Audio In Purple

AUTODOME IP 4000 HD Troubleshooting | en 51


14 TroubleshootingIf problems occur, check the installation of the camera with the instructions in this manual.Refer to this guide for further information.

Problem Solution

No video on screen. - Verify that the power is connected to all components in the system.- Verify that the power switch is ON.- Verify the status of cables or the connection of cables.

Poor video quality. -Check the powersupply voltage (normal24 VAC) directly at thecamera.

- Check the camera settings.- Check the video quality directly at the camera with a service monitor.- Check the quality and length of video cables, and possible EMC interference.- Check the quality of connectors and potential moisture/corrosion.- If the lens or the dome window is dirty, clean it with a clean cloth.

Camera is not workingproperly (includingwrong position ofcamera).

- Power-cycle the camera and power supply, or reset the camera using theconfiguration menu [Main > System > Reboot].- Check the connection of the power cable and the status of the camera.- Initialize the camera [Main > System > Initialize].- Check the power rating of the power supply.- Measure the voltage at the camera (since there could be a drop in voltage duecable length). The power consumption increases when the camera is moving(especially at high speed) and when the heater is on. The voltage at the camerashould always be 24 VAC (+/- 10%).

The surface of thedome case is hot.

- Check the voltage level of the dome camera and the status of the camera.- Check that the camera is connected to the proper power.

The image on thescreen flickers.

- Check to see if the camera faces directly into the sun or a fluorescent lamp. Ifso, reposition the dome. - Check for flickers on the screen.

52 en | Maintenance AUTODOME IP 4000 HD


15 Maintenance

All bubbles require special care when handling and cleaning to avoid scratches.

Notice!To avoid excessive moisture saturation inside the housing, limit the amount of time that thebubble is disconnected from the housing. Bosch recommends that the bubble be removedfrom the housing for no more than five (5) minutes.

Bubble HandlingThe bubble may be packaged with a protective plastic sheet. It is recommended that thebubble remain stored this way until it is ready to install. Limit handling the bubble, as anyscratches can quickly affect visibility.

Bubble CleaningIf cleaning the bubble is required, use the following procedures and comply with all thewarnings listed below.

Cleaning the Bubble InteriorThe extremely soft interior surface should not be cleaned by rubbing or dusting with a cloth.Use clean dry compressed air, preferably from a spray can, to remove any dust from theinterior surface.

!

Warning!Do not use alcohol-based solutions to clean the bubble. This will cause the polycarbonate tocloud and over time cause stress aging, which makes the bubble brittle.

AUTODOME IP 4000 HD Maintenance | en 53


Cleaning the Bubble ExteriorThe exterior of the bubble is hard coated for extra protection. If cleaning becomes necessary,only use cleaning solutions and cloths suitable for cleaning safety glass lenses. Dry the bubblethoroughly with a dry nonabrasive cloth to prevent water spots. Never scrub the bubble withany abrasive material or cleaners.Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean &Shine (or equivalent), according to manufacturer’s instructions. Refer towww.novuspolish.com to order or to find a local distributor.

Cautions– Do Not clean bubbles in the hot sun or on very hot days.– Do Not use abrasive or highly alkaline cleaners on the bubble.– Do Not scrape the bubble with razor blades or other sharp instruments.– Do Not use Benzene, Gasoline, Acetone, or Carbon Tetrachloride on the bubble.

http://www.novispolish.com

54 en | Decommissioning AUTODOME IP 4000 HD


16 Decommissioning16.1 Transfer

The unit should only be passed on together with this installation guide.

16.2 Disposal

DisposalYour Bosch product has been developed and manufactured using high-quality materials and components that can be reused.This symbol means that electronic and electrical devices that have reachedthe end of their working life must be disposed of separately fromhousehold waste.In the EU, separate collecting systems are already in place for usedelectrical and electronic products. Please dispose of these devices at yourlocal communal waste collection point or at a recycling center.

AUTODOME IP 4000 HD Technical data | en 55


17 Technical data

Bosch Sicherheitssysteme GmbHRobert-Bosch-Ring 585630 GrasbrunnGermanywww.boschsecurity.com© Bosch Sicherheitssysteme GmbH, 2017

Bosch Security Systems, Inc1706 Hempstead RoadLancaster, PA, 17601USA

autodome ip 4000 hd/5000 hd/ir

Documents