axis a8105-e installation...l01 l02 co no/ nc i/o rel 12v 24v v+ com no nc rex power supply max 30v,...
TRANSCRIPT
AXIS A8105-E installationRelay powered by PoE (12V)
Relay Door DoorRELAY
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuitOpen circuitClosed circuit
To check relay state, go to: Setup > System Options > Ports & Devices > I/O ports
Depending on your lock type, con�gure the following valuesfor RELAY, and click Save.
Open circuit for a fail-secure lockClosed circuit for a fail-safe lock
1.
2.
Configure relay state in AXIS A8105-E built-in web pages
12V l01
l02 CO
NO
/N
C
Relay powered by separate power supply
AXIS A8105-E installation
Relay Door DoorRELAY
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuitOpen circuitClosed circuit
To check relay state, go to: Setup > System Options > Ports & Devices > I/O ports
Depending on your lock type, con�gure the following valuesfor RELAY, and click Save.
Open circuit for a fail-secure lockClosed circuit for a fail-safe lock
1.
2.
Configure relay state in AXIS A8105-E built-in web pages
12V l01
l02 CO
NO
/N
C
Powersupply
AXIS A8105-E installationPotential-free relay
Relay Door DoorRELAY
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuitOpen circuitClosed circuit
To check relay state, go to: Setup > System Options > Ports & Devices > I/O ports
Depending on your lock type, con�gure the following valuesfor RELAY, and click Save.
Open circuit for a fail-secure lockClosed circuit for a fail-safe lock
1.
2.
Configure relay state in AXIS A8105-E built-in web pages
12V l01
l02 CO
NO
/N
C
Potential-freecontact
12V Fail-secure lock powered by PoE from door stationRecommended setup using AXIS TA8501 Physical Tampering Switch
AXIS A8105-E installation
These instructions apply when you use the recommended setup for AXIS TA8501 Physical Tampering Switch with AXIS A9801 Security Relay.
See con�guration on next page
Page 1/2
12V l01
l02 CO
NO
/N
C
I/O
REL
V+
COM
NO
NC
REX
12V24V
1. To check relay and tampering state, go to: Setup > System Options > Ports & Devices > I/O ports
2. Make sure the following values are con�gured for IO1.
Input TamperSwitch TamperingIO1
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuit
Relay Door DoorRELAY
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuitOpen circuitClosed circuit
3. Depending on your lock type, con�gure the following values for RELAY, and click Save.
Open circuit for a fail-secure lockClosed circuit for a fail-safe lock
4. Go to: Setup > Events > Action Rules
5. Modify “TAMPERING: Tilt detected” to the following values and click OK.
Configure relay and tampering state in AXIS A8105-E built-in web pages
Start condition onlyTrigger: Input Signal
Digital Input Port
TamperSwitch (Port2)Active: Yes No
Recommended setup using
AXIS TA8501 Physical Tampering Switch
Page 2/2
AXIS A8105-E installation12V Fail-secure lock powered by PoE from door stationOptional setup using AXIS TA8501 Physical Tampering Switch
These instructions apply when you use the optional setup for AXIS TA8501 Physical Tampering Switch with AXIS A9801 Security Relay.
NOTE: With this setup you can't notify the user if the tampering switch triggers, but IO1 is available for other use/con�gurations.
See con�guration on next page
Page 1/2
12V l01
l02 CO
NO
/N
C
I/O
REL
V+
COM
NO
NC
REX
12V24V
Optional setup using
AXIS TA8501 Physical Tampering Switch
Page 2/2 Configure relay and tampering state in AXIS A8105-E built-in web pages
1. To check relay state, go to: Setup > System Options > Ports & Devices > I/O ports
2. Depending on your lock type, con�gure the following values for RELAY, and click Save.
Open circuit for a fail-secure lockClosed circuit for a fail-safe lock
3. Go to: Setup > Events > Action rules
4. Clear the checkbox for the "TAMPERING: Tilt detected" action rule.
Relay Door DoorRELAY
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuitOpen circuitClosed circuit
TAMPERING: Tilt detected Detectors - Tilt Detection - Output Port -
AXIS A8105-E installation12V Fail-secure lock powered by external power supplyRecommended setup using AXIS TA8501 Physical Tampering Switch
These instructions apply when you use the recommended setup for AXIS TA8501 Physical Tampering Switch with AXIS A9801 Security Relay.
See con�guration on next page
Page 1/2
12V l01
l02 CO
NO
/N
C
I/O
REL
12V24V
V+
COM
NO
NC
REX
Powersupply
Max 30V,Max 1.2A
1. To check relay and tampering state, go to: Setup > System Options > Ports & Devices > I/O ports
2. Make sure the following values are con�gured for IO1.
Input TamperSwitch TamperingIO1
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuit
Relay Door DoorRELAY
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuitOpen circuitClosed circuit
3. Depending on your lock type, con�gure the following values for RELAY, and click Save.
Open circuit for a fail-secure lockClosed circuit for a fail-safe lock
4. Go to: Setup > Events > Action Rules
5. Modify “TAMPERING: Tilt detected” to the following values and click OK.
Configure relay and tampering state in AXIS A8105-E built-in web pages
Start condition onlyTrigger: Input Signal
Digital Input Port
TamperSwitch (Port2)Active: Yes No
Recommended setup using
AXIS TA8501 Physical Tampering Switch
Page 2/2
AXIS A8105-E installation12V Fail-secure lock powered by external power supplyOptional setup using AXIS TA8501 Physical Tampering Switch
These instructions apply when you use the optional setup for AXIS TA8501 Physical Tampering Switch with AXIS A9801 Security Relay.
NOTE: With this setup you can't notify the user if the tampering switch triggers, but IO1 is available for other use/con�gurations.
See con�guration on next page
Page 1/2
12V l01
l02 CO
NO
/N
C
I/O
REL
12V24V
V+
COM
NO
NC
REX
Powersupply
Max 30V,Max 1.2A
Optional setup using
AXIS TA8501 Physical Tampering Switch
Page 2/2 Configure relay and tampering state in AXIS A8105-E built-in web pages
1. To check relay state, go to: Setup > System Options > Ports & Devices > I/O ports
2. Depending on your lock type, con�gure the following values for RELAY, and click Save.
Open circuit for a fail-secure lockClosed circuit for a fail-safe lock
3. Go to: Setup > Events > Action rules
4. Clear the checkbox for the "TAMPERING: Tilt detected" action rule.
Relay Door DoorRELAY
Name Port TypeI/O Usage Normal state is... Current Status
Open circuitOpen circuitOpen circuitClosed circuit
TAMPERING: Tilt detected Detectors - Tilt Detection - Output Port -