Application street strip circle other

Axle Type alloy alloy(c-clip style) hy-tuf

Carrier Brand & Type (posi, spool...)

Brake Description (drum, disc, manfacturer...)

Spline Count Bolt Circle 1 Bolt Circle 2 A (register) D (flange)

Special Instructions

Axle Order Form 847-663-1701 FAX 847-663-1702BILLING ADDRESSBILLING ADDRESSName:

Phone:

Address

City State Zip

SHIPPING ADDRESSSHIPPING ADDRESSName:

Phone:

Address

City State Zip

ORDER DETAILSORDER DETAILSPackage #

Type of Rear & Additional Notes:

AXLESAXLES The information below is required for all ordersThe information below is required for all orders WHEEL STUD INFORMATIONWHEEL STUD INFORMATION(check allthat apply) Screw-in Wheel

studs 5/8”-18 (stud kit part #)

MEASURING PRE-EXISTING AXLES FOR UPGRADEMEASURING PRE-EXISTING AXLES FOR UPGRADE DIMENSIONSDIMENSIONS

B

H Driver Side C

Passenger Side C

X BoltCircle

2.645 4.50

2.792 4.75

2.939 5.00

3.233 5.50

MEASURING REAR END FOR UPGRADING AXLESMEASURING REAR END FOR UPGRADING AXLES DIMENSIONSDIMENSIONS

F

J

M

(J+M)

O

L

(O+L)

Axle Flange to Axle Flange

Housing End to Housing End

INDICATE TYPE OF HOUSING END INDICATE TYPE OF HOUSING END Check the corresponding box next to the housing end typeCheck the corresponding box next to the housing end type

Strange Ford 8.8”H1138

Factory Ford 8.8”

Big FordH1135

Late Big FordH1137 H1148

MustangH1134

Factory 05-up Mustang

OldsH1132 H1142

Strange Small GMH1143

Factory Small GM

Factory Large GM

Mopar H1133

Mopar H1147

Symmetrical H1131

Symmetrical H1136

(same as billing)

Note: LHD configuration is assumed throughout this form

1/2”-20 x 2”1/2”-20 x 3”

Press-in Wheel Studs

Axle Order Form Dimension Definitions & Common Sizes

Brake RegisterCenters the factory OEM brake drum or rotor and where applicable the wheels. Rotors applied in drag racing are typically centered by the wheel studs and have an oversized center allowing compatibility with various brake register sizes. Chrysler/Dana/Mopar common A dimensions: 2.300 or 2.820 Ford common A dimensions: 2.430, 2.525, 2.750, 2.780, 2.796, 2.875 or 3.060 General Motors common A dimensions: 2.780, 2.812 or 3.060

Bearing ShoulderThis is the bearing stop machined on the axle. This feature is not applicable to c-clip style axles. This is not identical to the F axle offset dimension since most axle bearings protrude from the housing end. The type of bearing, sealed ball or tapered, will result in a different axle offset using the same B dimension. If an original type of bearing is not used then the B dimension will need to be changed in order to maintain the original wheel offset. Chrysler/Dana/Mopar common B dimensions: 2.200, 2.3125 or 2.5625 Ford common B dimensions: 1.875, 2.0625, 2.125, 2.250, 2.375, 2.4375

Axle Overall Length This dimension is taken from the outside face of the axle flange to the end of the splines. Driver side and passenger side typically have different C dimensions. Measurement must be precise, best accomplished by using a straight edge and tape measure.Please let us know if you have given a C dimension with an existing carrier and intend to change the carrier. The change may alter the C dimension.

Axle Flange DiameterØ 6.245 is the Strange Engineering standard axle flange diameter unless otherwise specified. Customer must request a different size if clearance with the rotor or drum is an issue.

Axle Offset (Brake Gap)Measured from outside face of axle flange to the outside face of the housing end. Ford common F dimensions: 2.145, 2.3326, 2.500, 2.625 General Motors common F dimension: 2.8325

Axle Offset (Brake Gap) with Chrysler or Mopar RearendsMeasured from outside face of axle flange to the outside face of the housing end. On Chrysler/Dana/Mopar type housing ends, F is obtained with the backing plate and gasket installed or combined thickness accounted for. If aftermarket disc brakes are being used then it’s best to remove the axle bearing and supply the B dimension to ensure proper fitment of axles. Chrysler/Dana/Mopar common F dimensions: 2.3125, 2.423 or 2.673

Bearing Journal DiameterDiameter on which the axle bearing is pressed onto. Dimension is not required if purchasing bearings with axle order. Chrysler/Dana/Mopar common H dimension: 1.5635 Ford common H dimensions: 1.379, 1.400, 1.532, 1.563, 1.626 or 1.773 General Motors common H dimensions: 1.379, 1.400, 1.532, 1.563, 1.626 or 1.773

Distance from outside face of driver side axle flange to center of pinion

Distance from outside face of passenger side housing end to center of pinion

Distance from outside face of passenger side axle flange to center of pinion

Distance from outside face of driver side housing end to center of pinion

Distance Between Centers of Wheel Studs for Calculating Bolt CircleMeasurement is taken from the center of one wheel stud to the center of the wheel stud closest to it. This dimension is used as a reference to calculate the bolt circle (B.C.)Only applies to 5 wheel stud pattern. This does NOT apply to a 4,6 or 8 wheel stud pattern.

A

B

C

D

F

H

X

F

J

L

M

O