az press parts catalog

Replacement parts avai lable forA.B.DICK • CHIEF • DAVIDSON • GESTETNER • HAMADA

HEIDELBERG • ITEK • MULTILITH • RYOBI • TOWNSEND-51

SAVE ON SHIPPING BY USING YOUR VISA, MASTERCARD, AMERICAN EXPRESS, PAYPAL, OR CHECKS-BY-FAX

PRICES ARE SUBJECT TO CHANGE

Pages 1-6 Pages 32-35 Pages 36-39

Pages 21-31

Pages 31-34

Pages 13-16 Pages 7-12

Pages 18-20

7Pages 13-16

97% OF ALL REPLACEMENT PARTS IN STOCK

QUICK SERVICE, LOWEST PRICES, AND IMMEDIATE SHIPMENT.CALL US AT 1-800-922-2425

OR FAX US AT 1-480-922-8550

2007 - 2008 EDITION

SAME DAY SERVICE

PRINTER’S PARTS STORE

THIS BOOKLET HAS

ONLY A SAMPLE OF OUR

TOTAL INVENTORY OF OVER 100,000

DIFFERENT ITEMS IN STOCK.

IF YOU DON’T SEE IT JUST CALL OR FAX

PART # PART #

1 THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: A.B. DICK 350, 360, 360PRO, 369, 8805, 8810, 8815, 8820,

FILTER ASSEMBLY P-1147(A) Tube P-1146(B) Filter (need 2) P-1148Plug (not shown) P-1150

••• Rather than buy a new cradle, replace only the parts that wear.CRADLE REPAIR KIT - For 8800 & 9800 series.Complete Kit P-98037(A) Washer P-613(B) Hex nut - 2 ea. P-514(C) Retaining ring P-707(D) Shaft P-98038(E) Key P-1745(F) Ball bearing - 2 ea. P-11149(G) Steel bushing P-98058(H) Cradle (w/ shaft and bearing) P-98041

PUMP VANE (need 4 per pump)350, 360, 375, 8800, 9800 P-1159380, 382, 385 P-1931

FLEXIBLE SPEED CONTROL SHAFTFor the 8800 & 9800 seriesShaft P-98053Set screw P-7

CRANK ASSEMBLY Speed control

Complete - 350, 360, 375, 385 P-36060Complete - 9800 P-98060(A)Handle P-36062(B)Spring for handle P-36410Mounting screw P-299

SPEED PULLEYVariable P-1630Heavy duty (all steel) P-1631

FEEDER CLAMPThumb screw P-1539Adjusting clamp P-36087

••• MADE OF DURABLE ZINC DIE CAST!

STOCK RETAINER PLATE GUIDE350, 360 Center P-36712350, 360 Right hand P-36092350, 360, 375, 9800 Left hand P-36089385 Back guide plate P-38089

MICRO GUIDE ADJUSTING KIT

FOR ACCURATE FEED & REGISTRATION350, 360 P-36113375, 9800 P-37113

BACK PAPER GUIDE P-36090

THUMB NUT P-1058

SPRING GUIDE350, 360, 375 P-36088385 Side P-38088385 Back P-38090Screw P-984

TABLE RELEASE LEVER ASSEMBLY350, 360, 375, 385 P-369699800 P-37969

A

B

D

B A

C

F

G

E

A B

TABLE RAISE HANDLE ASSEMBLY

350, 360, 375 For feeder P-369559805 - 9850 For feeder P-98955

380, 385 For feeder P-38955 Chain del. 350,360,375,385 P-362630 Chain del. 9800 P-982630

TABLE RAISE GEAR & RATCHET ASS’Y.For feeder hand crank on 350, 360, 375, 9800350, 360, 375 (complete) P-369759800 P-98975Gear P-36974Ratchet 350, 360, 375 P-36973Ratchet 9800 P-98973Screw (3 needed) P-44

TABLE RAISE SHAFT ASSEMBLY - 9800Complete P-98070Shaft P-98102Gear P-38103Sprocket P-36101

COUNTER ASSEMBLYComplete P-36952Counter P-36954Mounting screw P-229Arm P-36956Screw for arm P-151Wheel (screw on type) P-36958Screw for wheel P-1056

COUNTER SENSOR SWITCH

9900 Series P-9814

BLEEDER VALVE ASSEMBLYComplete P-36847(A) Valve body P-36844(B) Shaft P-36841(C) Plug P-36951(D) Spring (inside) P-36859(E) Valve (inside) P-36845(F) Roll pin P-379

SUCKER TUBES WITH SHUT OFF VALVE ON BOTTOM••• Ideal for envelope runs and T-Heads.Shut off tube P-36990Sucker tube (standard) P-36174

Paper leveler assy. P-36164Paper leveler tube P-36166Plug P-36172Compensating sucker tube w/shut off valve P-36966

SUCKER FOOT•••P-1555 MATERIAL IS NEW TACKY GUM RUBBER TO ENSURE BETTER SHEET PICK UP.

All presses (cup) each P-1555*Extra heavy (cup) each P-5219Flat disc (3/4” dia.) each P-1552Flat disc (1/2” dia.) each P-1554*Note: P-1555 Sold individually or in bags of 50 or 100.

BLOWER TUBE SHUT OFF VALVE - All modelsP-36760

SPRING For feed roller support armsP-36177

C

A B

FE

D

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

PART # PART #

2

375, 9805, 9810, 9815, 9820, 9835, 9840, 9850, 9865, 9870, 9880, 380, 382, 385

UPPER FEED ROLLER

350, 360 P-36157375, 9800 P-371579870, 9910XCS, 9910 XCS P-98157 385 P-38157Arm 350, 360, 375, 9800 P-36175Bearing (plastic) P-1566

SHAFT & LEVER ASSEMBLY For upper feed roller

Complete 350, 360 P-36147Complete 375, 9805 - 9850 P-37147Shaft only 350, 360 P-36149Shaft only 375, 9805 - 9850 P-37149Lever (operators side) P-36171Lever & cam assy. (n.o.s.) P-36151Pin P-349

STUD - For feed roll shaft assembly

350, 360, 375, 385, 9800 P-1561

STUD - For upper forwarding feed roll shaft assembly.9870, 9890 P-8270

SCREW - For P-8270 P-6512

SUPPORT ARMS - For upper feed roller

Operators side P-36153Non-operators side P-36155

FINGER ASSEMBLY & BLOWER TUBE350, 360, 375, 9800 P-36158 69.80385 P-38158 164.50

HOSE For blower tube350, 360, 375, 9800 P-1189 1.80380, 385 P-1677 4.80

SOLENOID 9800 impression cylinder power lever

P-4029 57.30

PAPER SENSOR For AB Dick 9800Complete P-98269 57.90Sensor arm P-98974 2.40Spring P-98581 4.90

FEELER CONTROL LEVER ASSEMBLY350, 360, 375, 9805, 9810, 385

P-36839 145.80

IMPRESSION CYLINDER GRIPPER FINGERS••• Sand blasted tips for better grip.350 (1/2”) P-35225 39.90360, 385 (1/4”) P-36225 25.90375, 9800 (small) P-37224 22.00375, 9800 (large) P-37225 25.90Mounting screw P-268 .60

PAPER WEIGHT BAR

Light weight 350, 360 P-36094 18.90Heavy weight 350, 360 P-36093 15.00Light weight 375, 9800 P-37094 12.00Heavy weight 375, 9800 P-37093 12.60

PAPER STOP Impression cylinder350 P-35241360 P-36241375, 9800 P-37241

LEVER ASSEMBLY For impression cylinder

P-36207

SEGMENT Imp. cylinder P-36203

GRIPPER SHAFT ASSEMBLY For impression cylinderComplete 350, 360 P-36229Shaft only P-36231Gear P-36235Taper pin P-421

BLANKET CYLINDER SHAFT350, 360 P-36290375, 9800 P-37290380, 382, 385 P-38290

PRINT ADJUSTING DRAW ROD 350, 360 (30° pressure angle) P-36180 77.90

(20° pressure angle) P-36308 54.90 375, 9800 (30° pressure angle) P-37180 77.90

(20° pressure angle) P-37308 39.90 385 (30° pressure angle) P-38180 104.90

(20° pressure angle) P-38308 66.00RETAINER P-36182 6.00NUT P-36186 10.50

BLANKET CYLINDER RING SEGMENTS••• New style - Case hardened for longer wear.Left hand P-36194 62.00Right hand P-36195 62.00

(A) SCALE Blanket cylinder raise & lower 2 screws needed P-36208 2.90

(B) SCALE Blanket cylinder adjustment 5 screws needed P-36202 6.90

DRIVE SCREW For both scales (not shown) P-1040 .60

BLANKET BARS Standard360 P-36252 125.90375, 9800 P-37252 136.00380, 382, 385 Serial #1305 & below P-38252 300.009880 P-988252 319.90Mounting screw P-36204 2.00Blanket screw P-124 .60

QUICK CHANGE BLANKET BARS••• Save time & money by changing only 4 screws to mount your blanket.360 P-36777 129.90375, 9800 P-37777 139.90380, 382, 385 P-38777 340.009880 P-988777 380.00Mounting screws P-36204 2.00Blanket screws P-124 .60

A B

PART # PART #



BEARING HOUSING COMPLETE For blanket cylinder• Made of “REINFORCED STEEL” for longer life.• Completely enclosed for added strength.

(A) Operators side P-36295 109.80(B) Non-Operators side P-36283 109.80

BLANKET CYLINDER ADJUSTING SHAFT

350, 360, 375 P-36236 42.009800 P-98236 95.10

CYLINDER GEARS••• All cylinder gears are made with “SOLID STEEL” for longer life.Master cylinder gear 350, 360, 375 P-36313 246.90Master cylinder gear 9800 P-98313 294.90

Inner blanket cylinder gear 350, 360, 375 P-36214 302.00 5/16” wider than standard for longer life.Inner blanket cylinder gear 9800 P-98214 249.90“Wide” inner blanket cylinder gear P-36211 308.50Outer blanket cylinder gear 350, 360 P-36196 320.00Outer blanket cylinder gear 369 P-36198 261.00Outer blanket cylinder gear 375, 9800 P-37196 259.90Outer blanket cylinder gear 385 P-38196 246.00

Impression cylinder gear P-36191 123.90

PLATE CYLINDER UPPER SUPPORT ARMS350, 360 P-36801 69.90375, 9800 P-37801 60.00

PLATE CYLINDER LOWER SUPPORT ARMS350, 360, 375, 9800(9/16” hole)

P-36833 72.50

STUD - For master cylinder support arm.9890, 9900 P-4577 9.00

WATER FOUNTAIN HOSEP-1549 2.90

IDLER GEAR Water sectionPlastic P-36368 19.90

HARDWARE REPAIR KIT For Super Aquamatic.Complete P-36376-K 8.40

Consists of 2 ea. P-36376 Shield 1.40P-658 Spring washer .80P-617 Flat washer .60P-706 Retaining ring 1.00

*ALL PARTS SOLD SEPARATELY.

WATER FOUNTAIN BOTTLE ASSEMBLY.

••• The valve assembly is made of hardened plastic which helps eliminate build up and rust.

(1 quart) P-1915 21.90350, 360 only (2 quart) P-1919 59.80

COUPLING ASSEMBLY For water waver roller ass’y.

P-36426 74.90

COUPLING HOUSING For water waver roller ass’y.P-36432 37.50

IMPRESSION INNER BLANKET MASTER

IMPROVED

CHROME WATER DUCTOR ROLLER (SMOOTH)350, 360 P-36342-S 339.90375, 9800 P-37342-S 380.00

CHROME WATER DUCTOR ROLLER (ROUGH)350, 360 P-36342-R 369.90375, 9800 P-37342-R 389.90

WATER FOUNTAIN ROLLER 350, 350T, 357, 357A, 367, 367A (Smooth Aluminum) P-35364 179.90 360, 360CD, 360T (Rough Aluminum) P-36364 179.90 375, 9800 (Rough Aluminum) P-37364 189.90

WATER DUCTOR ROLLER HOUSINGHousing (cone hub) P-36322 22.90Housing (flat hub) P-36366 16.00Bearing P-746 9.80

COMPRESSION SPRING (Painted Red)For water waver roller P-36413 2.20

SHAFT For water repellant waver roller

350, 360 P-36378 35.90375, 9800* P-37378 49.009800 PRO

•••Shaft is universal, fits old & new style.

TIRE Form roll knobs P-36399 3.50TIRE Ink fountain knob P-36244 4.50

NIGHT LATCH IDLER GEARBrass P-36446 29.90Steel P-36457 78.00Nylon P-36455 22.90

SINGLE LEVER CONTROL ARM

360 Complete P-36856 89.909800 Complete P-98856 104.00(without knob) P-36860 85.90Knob P-36858 18.70

INK OPERATING PAWL For ink metering fountain360 Pro P-36251 42.909800 P-98251 39.00

SPRING For lower ink oscillatorP-36459 4.60

FORM ROLL SHAFT350, 360 P-36401 85.80375, 9805 - 9850, 9865, 9870 P-37401 125.90


PART # PART #

4

375, 9805, 9810, 9815, 9820, 9835, 9840, 9850, 9865, 9870, 9880, 380, 382, 385

MASTER CYLINDER HEAD CLAMP ASSEMBLYFor 9800 - consists of all items shownCOMPLETE P-98352 579.90(A) Screw P-253 .60(B) Head clamp P-98353 280.00(C) Screw P-43 .60(D) Hinge P-98299 25.00(E) Plate clamp P-98359 53.00(F) Knob P-98175 23.90(G) Spring P-36707 1.30(H) Washer P-592 .60(I) Eccentric pin P-98351 59.90(J) Retaining ring P-668 .60(K) Bracket P-98171 5.00(L) Bar P-98387 111.90(M) Screw P-257 .60(N) Shoulder screw P-8042 7.50(O) Retaining ring P-666 .60(P) Bracket P-98181 5.00(Q) Spring P-36349 .90(R) Thumb screw P-98347 29.90(S) Bracket P-98153 28.50(T) Screw P-37 .60(U) Radial bar P-98393 82.90

HEAD & TAIL CLAMP ASSEMBLYFor 350, 360COMPLETE - 360 consists of all items shown P-36354 406.00COMPLETE - 375 consists of all items shown P-37354 599.90TAIL CLAMP ASSY. (A - F) P-36606 129.90TAIL CLAMP ASSY. (A - F) P-37606 214.90(A) C-Ring P-666 .60(B) Tail clamp (360) P-36323 99.90(B) Tail clamp (375) P-37323 137.80(B) Tail clamp (9800 not part of kit) P-98323 129.90(C) Pivot screw P-36331 9.90(D) Spring P-36325 1.90(E) Thumb screw P-1027 4.50(F) Spring P-36327 3.30HEAD CLAMP ASSEMBLY (G - S) P-36352 270.00HEAD CLAMP ASSEMBLY (G - S) P-37352 399.90(G) Lateral adj. knob P-36347 22.00(H) Washer P-569 .60( I ) Spring P-36349 .90(J) Pin bar (360) P-36345 219.90(J) Pin bar (375) P-37345 204.90(K) Bracket (360) P-36353 200.00(K) Bracket (375) P-37353 209.80(L) Spring P-36032 3.80(M) Washer P-586 .60(N) Spring washer P-1049 .90(O) C-Ring P-668 .60(P) Screw P-892 .60(Q) Hinge (360 & 375) P-36299 8.00(Q) Hinge (9800) P-98299 25.00(R) Stop plate (360) P-36359 139.80(S) Vertical adj. knob P-36351 19.90

FORM ROLL SEPARATING SHAFT9800/9900 Complete P-98497 180.00(A) Roll pin P-382 .60(B) Collar P-739 3.90(C) Cam - non-operators side P-36623 49.90(D) Shaft only P-37499 73.90(E) Cam - operators side P-36503 49.90(F) Eccentric collar P-747 12.90(G) Set screw P-8 .60(H) Taper pin P-424 .60( I ) Separating lever P-98505 44.90

INK DUCTOR LEVER ASSEMBLYComplete P-36572 19.90Lever only P-36569 12.50Bushing 360, 375, 9800 P-1569 4.30Bushing 380, 382, 385 P-1568 32.90Retaining ring P-703 .60

SEAL For ink fountain roller - 360Pro & 9800 (need 2)P-36262 4.60

INK DUCTOR OPERATING CAMP-36542 46.90

INK ROLLER RATCHET ASSEMBLY

360 PRO P-36263 74.909800 PRO, 9900 P-98263 128.00

Ratchet only P-36239 45.90

••• DESIGNED WITH REPLACEABLE “STEEL” END CAPS AND A DEEPER INK WELL FOR 50% MORE INK CAPACITY.INK FOUNTAIN ASSEMBLY350 Complete P-35071 624.00

Fountain only P-35072 440.00Wire P-35084 2.50

360 Complete P-36778 348.50Fountain only P-36789 199.80Wire P-36084 2.90

360 PRO Complete P-36805 405.20Fountain only P-36807 199.80

375, 9800 Complete P-37778 348.50Fountain only P-37789 209.90Wire P-37084 2.90

9800PRO Complete P-98805 400.00Fountain only P-98807 204.90

All models Adjusting screw P-1570 6.00350, 360, 375, 9800 End caps P-36792 52.90360PRO, 9800PRO End caps P-98792 52.90

INK FOUNTAIN BLADE350 1-3/4” wide P-35079 49.50

2-7/8” wide P-35233 99.90360, 360PRO 1-3/4” wide P-36079 42.90

2-7/8” wide P-36233 84.90375, 9800 1-3/4” wide P-37079 72.90

2-7/8” wide P-37233 89.90385 Standard width P-38079 149.90

Screw P-118 .60

METERING BLADE With studs360 3-5/8” wide P-36095 104.909800 3-5/8” wide P-98095 132.00

I

H

F&GE

D C A&B

IMPROVED

PART # PART #



HEAVY DUTY CAM KIT For ink ductorP-36500 9.90

••• Uses a bearing in place of the Cam to prevent premature wear.

INK FOUNTAIN HAND CRANK9800 P-98402 90.00

CLUTCH PULLEY ASSEMBLY 360, 375, 9800 Complete hub I.D. 1/2” P-36597 324.90 9800 QPC, PRO Complete hub I.D. 7/8” P-98597 324.90 (A) Spring P-36591 12.90

(B) Pinion P-36595 39.90(C) Link P-36593 8.00(D) Lever P-36605 59.90(E) Pulley only 360 P-36587 132.90(E) Pulley only 9800 P-98587 97.00

OVERSIZED CLUTCH PULLEY For thermographers 360 Complete P-36589 362.90

Pulley only P-36599 167.90

SPRING HOLDER & SLEEVE KITUsed in place of old design single piece.9800 Series P-98595-K 52.90

SENSOR For 9800 clock sync. mechanismMale connector P-4047 26.00

SENSOR For 9800 clock sync. mechanismFemale connector P-4032 34.90

FEELER LINK OPERATING LINK ASSEMBLY

350, 360, 375, 9800 P-36885 66.80380, 382, 385 P-38885 133.50

GAP CONTROL SHAFT ASSEMBLY 350, 360 Complete P-36689 169.90 375 Complete P-37689 194.90 9800 Imp. Cyl. Complete P-98689 139.50 9800 Master Cyl. Complete P-98693 140.00 350, 360 Shaft only P-36695 55.00 375 Shaft only P-37695 62.90 9800 Imp. Cyl. Shaft only P-98695 84.00 9800 Master Cyl. Shaft only P-98697 84.00 350, 360, 375, 385 Dial assy. P-36688 84.50 8800, 9800 Dial assy. P-98688 80.00

HANDWHEEL

350, 360, 375, 8805/10 P-36615 112.90

SPLINE DISC Safety handwheel

P-99665 32.90

BLOCK IS COLD WELDEDWHICH MAKES IT LESS BRITTLE.

IMPROVED

A

C

BD

E

DRIVE SHAFT AND GEAR ASSEMBLY COMPLETE350, 360 P-36577 74.90375 P-37577 124.909865 P-98577-65 245.809870 P-98577-70 150.00

DRIVE SHAFT 350, 360 P-36583 42.90375 P-37583 97.909800 - 1/2” O.D. P-98583 92.909800 - 5/8” O.D. P-98388 89.909865 P-98583-65 218.909870 P-98583-70 121.90380, 385 P-38583 190.00

HOUSING Non-operators side 350, 360 P-36487 44.90375 P-37487 119.909800 TD/CD/QP/QPC/PRO P-98487 56.40

HOUSING ASSY. 9800 TD/CD/QP/QPC/PRO P-98385 143.90

HOUSING Operators side 350, 360 P-36585 49.90375, 9800 P-37585 107.809800 QPC, PRO P-98585 92.90

DRIVE GEAR 350, 360, 375 P-36581 34.909800, 380, 385 P-38581 36.90

CONTROL PANEL OVERLAY & MEMBRANE(A) 9815, 9850 P-98540 214.90(B) 9870 P-98562 529.90

POWER SUPPLY

9800 Control box (5V. 115V.)P-4401 329.90

DRIVE & PUMP SWITCHOld style (drive & pump) - 2 position with screw connectors

P-36977 22.00

(385) Momentary - 3 position with tab connectors

P-38977 31.00New style (motor) momentary- 3 position with tab connectors

P-36303 19.90

New style (pump) - 3 position with tab connectorsP-36307 16.00

New style (pump) - 2 position with tab connectorsP-36305 12.50

RELAY - 9800 Control boxP-4037 36.00

MICRO SWITCH Chain delivery safety guards

P-362940 38.80

TIMING PULLEY ASSEMBLY350, 360, 385 P-362080 40.90375, 9800 P-372080 89.90Shaft only 350, 360, 385 P-362040 5.10Shaft only 375, 9800 P-372040 49.90Pulley only all models P-362120 35.90


PART # PART #

6

375, 9805, 9810, 9815, 9820, 9835, 9840, 9850, 9865, 9870, 9880, 380, 382, 385

JOGGER OPERATING LEVER - New style350, 360, 375 P-361610 72.90

SIDE JOGGER LEVER9800 P-984130 24.00

LEVER SUPPORT P-984140 27.80

GEAR & SHAFT ASSEMBLYChain delivery P-36754 122.90Chute delivery P-36752 135.80385 P-38754 329.809800 P-98754 122.90

SHAFT & SPROCKET ASSEMBLY350, 360 (12-1/4” Inside sprocket to sprocket) P-361160 559.90350, 360 (12-1/16” Inside sprocket to sprocket) P-361165 559.908810 P-881160 499.90375, 9800 Standard P-371160 559.909800, 1-1 P-981160 559.90

••• Reinforced anvil is made of steel which prevents bowing and lasts longer.

GRIPPER BAR ASSEMBLY350, 360 Complete P-360990 240.00375, (9800 standard) Complete P-370990 219.609800 (1 to 1) P-980990 240.00385 Complete P-380990 999.80(A) Gripper finger P-361020 11.00(B) Pin (for finger) P-3001 .50(C) Anvil 350, 360 P-361090 99.90(C) Anvil 375, 9800 (universal) P-371090 71.90(C) Anvil 385 P-381090 759.90(D) Butterfly spring 350, 360 P-361070 1.10(D) Butterfly spring 375, 9800 P-371070 1.50(D) Butterfly spring 385 P-381070 2.50(E) Shoulder screw P-8032 3.00(F) Shaft 350, 360 P-361060 31.90(F) Shaft 375, 9800 P-371060 59.90(F) Shaft 385 P-381060 61.90(G) Shaft bearing P-361000 9.30(H) Cam P-1416 4.20( I ) Stud P-401 .60(J) Lever 350,360,375,9800standard,385 P-361040 38.80(J) Lever 9800 (1 to 1) P-981040 22.00(K) Loop spring P-361080 .80

GRIPPER BAR REPAIR KIT••• Comes with all parts (less anvil & shaft) to repair one gripper bar.350, 360 P-30730 105.90375, 9800 Std. & 1-1 P-30731 105.90385 P-30732 223.90

TAPE TRACK (18 inches)••• Made of “sand paper like” material that holds better.For star wheels on 9800, 1 to 1 chain deliveries

P-983130 1.50

H

IDEKC

G A F BJ

BACK STOP 350, 360, 375 P-362420 129.909800 P-984320 140.009800, 1-1 P-982420 69.90

••• Made with spring steel & nickel plating which prevents cracking and adds better spring action & durability.

BACK STOP SPRINGComplete with cam350, 360, 375, 385 P-362300 54.90Complete with cam-9800 P-982300 70.00Spring only P-362320 29.90Spring only P-982320 49.90Cam P-1521 8.20Pin P-3002 6.90

DELIVERY GRIPPER CHAINSSold in a set of 1 Left hand & 1 Right hand350, 360, 375, 9800 O.S., 385N.S. 5/8” carrier link P-361390 159.90O.S. 1/2” carrier link P-361100 159.90new style 9800, 1 to 1 CD- 6” star wheels with tapes P-981390 64.00

ARMS For 9800 1 to 1 chain delivery safety guards

Operators side - complete P-984289 30.00Arm only OS P-984290 22.90

Non-oper. side - complete P-984279 30.00Arm only NOS P-984280 22.90Cam P-1475 5.40Pin P-3012 .80C-ring P-679 .60

INK WASH UP ATTACHMENT

350, 360 P-36773 195.00375 P-37773 199.90

REPLACEMENT WASH UP BLADES350, 360 (11-5/8 x 1-5/8) 4 holes P-5028 7.50350, 360 (11-3/4 x 2-1/16) no holes P-36767 8.90375 (12-7/8 x 1-5/8) 4 holes P-5029 8.509800 (13-1/4 x 2) 6 holes P-30200 25.959800XLK (13-1/4 x 2-1/16) 6 slots P-30216 25.959985 (14-3/32 x 1-5/8) 6-holes P-30225 14.90Century 3000 (14 x 1-5/16) 7 holes P-30792 25.95

••• ELIMINATE COSTLY DOWNTIME WITH YOUR OWN EMERGENCY KIT FOR YOUR MODEL PRESS.

REPAIR KITS FOR ALL A.B. DICKSMaster kit P-1707 - 720 pcs. 262.90Junior kit P-5088 - 437 pcs. 126.00Nut kit P-1701 - 100 pcs. 44.00Washer kit P-1702 - 120 pcs. 52.90Screw kit P-1703 - 108 pcs. 52.90Ring kit P-1704 - 228 pcs. 79.80Pin kit P-1705 - 136 pcs. 59.80Spring kit P-1706 - 28 pcs. 55.00

IMPROVED

PART # PART #


Replacement parts for : MULTI 1210, 1250OS, 1250W, 1250N, 1250DOM., 1215CD,

VARIABLE SPEED PULLEY1250 O.S. - 1/2” Shaft P-1629 179.901250 N.S. - 5/8” Shaft P-1649 120.00

V-BELTS

35” Motor to printing head P-4904 9.00

33” Pump to motor compound pulley P-1689 7.50

32” Compound pulley to machine P-1688 7.50

30” Compound pulley to machine P-1686 6.50

26” To machine P-4903 6.90

49” Conveyor drive P-1690 8.00

34” New style pump to motor P-1695 7.50

RATCHET PAWL ARM ASSEMBLYP-12979 68.00

SHEET SEPARATOR BRACKET ASSEMBLY

Complete P-12112 29.90(A) Nut P-497 .60(B) Ball retainer P-1105 9.00(C) Bracket P-12113 28.90(D) Screw P-149 .60(E) Washer P-557 .60(F) Sheet separator P-12114 .90

SHEET SEPARATOR - 1360

P-13114 1.30

SHEET SEPARATOR For TOKO 1218

P-128114 3.00

CENTER BLOWER KIT

Complete P-5065 82.90(A) Center blower P-12128 59.90(B) Thumb nut P-537 2.90(C) Lockwasher P-624 .60(D) Washer P-566 .60(E) Bracket P-12164 9.90(F) Retaining ring P-668 .60(G) Washer P-586 .60(H) Spring washer P-653 1.00(I) Valve stem P-12069 2.60(J) Hose - 27” P-5285 3.90

HUB FOR P-13085 OSC ROLLP-13440 86.90

SUCKER TUBE - 1650 P-16174 12.60

O-RING For sucker tubeP-5329 .60

SUCTION FEETDouble stem P-12170 99.90Single stem P-12990 160.00

PILOT SCREW P-12104 1.70

F C

D&E

BA

B

J I

C H

AE

DDH G

F

COMPENSATING SUCKER TUBE ASSEMBLYEXTENDS 1/4” FURTHER. ••• Excellent for running envelopes and heavy stock.1250 (Set of 2 w / block) P-12259 107.901250 (Tube only) P-12966 32.001850 (Set of 3 tubes only) P-18990 103.801870 (Set of 4 tubes only) P-18170 136.00

FLAT DISC SUCKER FOOT P-1552 .80

SUCKER FOOTFor Multilith 1218 & for Toko 4700, 4750

P-5203 2.50

PAWL LEVER For single sheet feed1330, 1360, 1650, 1860, 1960

P-13563 24.90

DRIVE LEVER ARM ASSEMBLY••• Made of 1/4” solid cast stock for longer life and durability.1250 P-12927 68.001330, 1360 P-13927 64.001650 P-16927 59.801850 P-18927 58.90

FEEDER LINKAGE DRIVE LEVER (near delivery)

P-12732 24.50

FEEDER PULLOUT ROLLERRoller with bearing P-12125 34.00Bearing only P-1371 5.50Spacer (on sides) P-12536 6.00Spring P-12181 1.90

SPRING For feeder pullout rollerP-12386 2.90

UPPER FEED ROLL HOLDER

1250 N.S. P-12115 16.501250 O.S. P-12274 29.90

HAND CRANK ASSEMBLY••• Made of solid white brass which helps prevent stripping.

Complete P-12955 140.00(A) Stud P-36962 19.90(B) Handle P-36961 24.90(C) Spring lock (inside) P-36959 2.40(D) Screw P-874 .60(E) Nut P-492 .60(F) Spring P-12909 2.50(G) Steel ball P-755 1.90

TABLE PAWL RELEASE LEVER

1250 P-12969 69.001330, 1360, 1650 P-13969 69.00

(A) CONVEYOR DRIVE SPROCKETS - O.S.

Front feed roller P-12555 11.60Rear feed rolller P-12559 11.60

(B) TENSION SPROCKET P-12522 4.90

TENSION ROLLER P-12425 14.00

IMPROVED

B

D E

A

A

B


PART # PART #

8

2650, 2850, 4150, 4250, 1330, 1360, 1315CD, 1650, 1820, 1860, 1870, 1960

CONVEYOR TIMING PULLEY - N.S. -Conveyor roller P-4242 80.00CONVEYOR TIMING PULLEY - N.S. -Front feed roller P-4257 30.00CONVEYOR DRIVE PULLEY - N.S. -Rear feed roller P-4258 20.00

SKID ROLLER ASSEMBLYWorks with P-12359 shown below.

Narrow wheel 1250 P-12434 59.90(A) Arm P-12436 44.90(B) Roller P-12454 14.90(C) C-ring P-680 .60Wide wheel 1850 P-18434 69.90(A) Arm P-12436 44.90(B) Roller P-12532 14.90(C) C-ring P-680 .60(D) Bushing (comes with Roller P-12532)

P-799 1.80

THUMB SCREW P-311 .80

SKID WHEEL HOLDER P-12359 6.90

SKID ROLLER ASSEMBLYFor old design skid wheels that uses posts. Complete 1250 P-12501 69.90Arm only P-14492 59.90Wheel only P-12532 14.90 Bushing (included w/ P-12532) P-799 1.80C-ring P-680 .60

CONVEYOR PAPER RETAINER P-12433 19.90

GUIDE ASSEMBLY - 1360 P-13403 18.40

CONVEYOR FEED TAPES

Regular plastic P-4957 7.40

Special cloth for easier feedingP-4955 32.00

PAPER GUIDE SPRING1250 P-12924 5.50SCREW P-191 .60

PAPER GUIDE SPRING - 1850 & 1860

P-18527 14.80

TAPE BAR P-12708 36.40

FEELER FINGER P-12141 12.90PILOT SCREW P-3073 4.90

EJECTOR PIN BAR - Universal for old & new style.1250 (7 Pin) P-12249 69.90

A

BC

REGISTER BAR ASSEMBLY (Complete) P-13703 402.60(A) Support rod P-13483 15.00(B) Register bar with scale P-13359 35.90(C) Screw P-225 .60(D) Lockwasher P-635 .60(E) Washer (comp. assm. takes 2) P-1811 .60(F) Spacer P-1415 3.30(G) Adjusting block (comp. assm. takes 2) P-13497 7.50(H) Thumb screw (comp. assm. takes 3) P-7220 2.00( I ) Skid roller and block assm. - short P-13492 89.90(J) Set screw (not shown) P-18 .60(K) Skid roller and block assm. - long P-13434 89.90(L) Thumb screw P-1807 1.90(M) Brass plug (short) (not shown) P-11795 1.60(N) Retaining ring (not shown) P-698 .60(O) Brass plug (long) for thumb screw “H” P-4788 .90

SPECIAL MICRO ADJUSTING NUT & STOPFor upper feed roll adjustment

P-12135 11.50••• NO TOOL NEEDED FOR FAST & EASY ADJUSTMENT!

PAPER FEED FRAME LEVERS1250 Old design (straight, no tab) P-12165 36.901250 O.S. & L.W. (straight, with tab) P-12156 24.901250 N & DOM. (bent, with tab) P-12151 36.901650 (straight) P-16156 24.901650 (bent) P-16151 36.90

CAM LEVER1250 P-12155 42.901650 P-16155 46.90

FEED FRAME ROLLER1250 P-12157 65.701330, 1360, 1650 P-13157 76.00

FOUR FINGER SHAFT ASSEMBLY -Complete 1250 New style (pyramid cam - no notch)

P-12393 156.00 -Complete 1250 Domestic (tear drop cam) P-12387 110.90 -Complete 1250 M / MG (notched pyramid cam & tear drop cam)

P-12381 120.00THREE FINGER SHAFT ASSEMBLY -Complete 1250 Old style P-12388 83.90

PAPER HOLD ATTACHMENT -Complete 1250 P-12840 239.90

IMPRESSION GRIPPER SHAFT & ARM ASS’Y.Complete P-12203 130.00Arm assembly P-12207 89.90Shaft only P-12205 28.90Arm only P-12197 88.00

IMPRESSION CYLINDER ADJUSTING SEGMENT

P-12733 31.80

PART # PART #



IMPRESSION GRIPPER HOLDER ASSEMBLYComplete P-12182 39.90(A) Finger O.S. P-12245 5.50(A) Finger N.S. P-12237 15.00(B) Holder P-12189 29.90(C) Screw (not shown) P-12187 1.00(D) Screw P-96 .60(E) Washer (not shown) P-586 .60

BUSHING For impression cylinder adjustment1850 Non-op. side P-18400 32.00

CYLINDER GEARSMaster (plate) P-12313 187.90Blanket P-12214 213.90Impression P-12191 229.90

••• All gears are hardened for longer life.

BLANKET CYLINDER SHAFTS1250 (.750 Dia.) P-12290 64.901250 (.010 Oversized dia.) P-12302 89.901330, 1360, 1650 (.1.125 Dia.) P-13290 177.901330, 1360, 1650 (.030 Oversized dia.) P-13302 177.901850 (1.125 Dia.) P-18290 219.901850 (.030 Oversized dia.) P-18302 325.00

CAM BAND - 1250 O.S. & N.S.

For blanket cylinder P-12178 80.00

MASTER CYLINDER ADJUSTING WRENCH

1250 O.S. P-12266 77.901250 N.S. P-12236 77.901360 (13” clamps) P-13266 39.901360 (16-1/2” clamps) P-13236 32.001960 P-19236 66.00

MASTER CYLINDER CLAMP LOCK LINK1330, 1360, 1650 P-13299 32.00

BLANKET CYLINDER CLAMP KITComplete (Trailing 11x17) P-14258 80.00(A) Screw P-12204 4.50(B) Spring P-12390 .90(C) Pin bar P-12922 31.00(D) Bracket P-14003 9.80(E) Nut bar P-14004 8.00(F) Screw P-12921 1.00

MASTER CYLINDER UPGRADE KIT

1650 P-13385 220.00

ACTUATING TOOL For plate cylinder latch

1330, 1360, 1650 P-5888 49.90

MASTER CYLINDER HOLD DOWN BRACKET - 1360, 1650

P-13357 72.50

B

A

D

CLAMP COMPLETE - Trail End P-13790 191.00(A) R.H. Bracket P-13377 12.50(B) Clamp P-13389 84.50(C) Special Nut P-11991 3.10(D) Retaining Ring P-666 .60(E) Spring P-13724 2.00(F) L.H. Bracket P-13379 12.50(G) Round Head Screw P-194 .60(H) Lockwasher P-623 .60(I) Pin Bar with Lever P-13323 69.90(J) Spring-Extension P-13309 2.10(K) Thumb Screw P-11783 9.00(L) Support P-16357 25.00(M) Flat Head Screw P-652 .60

1250 (10 X 15) MASTER CYLINDER ASSEMBLIES

Lead Edge - complete P-12788 100.00(A) Screw P-159 .60(B) Thumb screw P-1095 6.00(C) Nut (used on P-12788 only) P-1898 3.30(D) Nut (used on P-12790 only) P-12796 16.00(E) Handle (used on P-12790 only) P-12761 14.00(F) Screw P-12770 1.90(G) Pin bar (18 point*) P-12760 24.90(H) Clamp only - not sold alone - - - - - - - - - - - (I) Adjusting screw P-12812 41.00(J) Taper pin P-421 .70(K) Nut P-497 .60(L) Stem P-12793 12.50(M) Retainer (used on P-12790 only) P-12797 17.90(N) Spring (used on P-12790 only) P-12762 2.90

••• MADE OF ALLOY STEEL DIECAST FOR LONGER LIFE & GREATER DURABILITY.

PIN BAR CLAMP Master cylinder (10 X 15)18 Point - 10” long P-12760 24.90

CLAMP Blanket cylinder17 Point - 9-3/4” long P-12922 31.00

IMPROVED


PART # PART #

10

2650, 2850, 4150, 4250, 1330, 1360, 1315CD, 1650, 1820, 1860, 1870, 1960

16-1/2” ANGULAR ADJUSTING CLAMP ASSEMBLYComplete (1250) P-12702 419.80Complete (1360, 1650) P-13702 520.00Sub assy. - items (A) - (CC) (1250) P-12717 410.00Sub assy. - items (A) - (CC) (1360, 1650) P-13717 399.90(A) Screw P-161 .60(B) Pin bar (tail) - 22 point (1250) P-12746 52.90(B1) Pin bar (tail) - 11 point (1360, 1650) P-13746 36.00(B2) Pin bar (tail) - 13 point (1360, 1650) P-13659 50.00(C) Thumb screw P-1067 3.00(D) Bracket P-12729 14.90(E) Lockwasher P-624 .60(F) Collar P-927 5.90(G) Set screw P-3 .60(H) Shaft P-12726 23.00( I) Lateral adjusting block P-12736 16.00(J) Adjusting block P-12734 18.00(K) Retaining ring P-664 .60(L) Adjusting wheel P-12744 7.50(M) Washer P-1887 .60(N) Spring washer P-650 1.20(O) Shoulder screw P-8090 6.00(P) Pointer P-12745 3.50(Q) Spacer cam P-1402 6.00(R) Screw P-172 .60(S) Screw P-191 .60(T) Lockwasher P-623 .60(U) Retainer P-12738 5.90(V) Shoulder screw P-8089 5.90(W) Spring P-12724 3.90(X) Bracket (1250) P-12716 47.70(Y) Lead retainer P-12751 33.90(Z) Pin bar - (lead) - 22 point (1250) P-12739 42.00(Z1) Pin bar - (lead) - 13 point (1360, 1650) P-13739 36.00(Z2) Pin bar - (lead) - 11 point (1360, 1650) P-13652 51.00(AA) Clip nut P-12749 17.00(BB) Screw P-10323 .60(CC) Set screw P-1089 .60(DD) Shelf P-12705 64.80(DD) Shelf (1360, 1650) P-13705 74.50(EE) Screw P-12375 2.50

PLASTIC BOTTLE RECEPTACLE VALVEP-12347 14.30

WATER FOUNTAIN HOSE1250, 1850 O.S. (10-1/2”) P-1189 1.801850 N.S. (19”) P-1181 5.00

BOTTLE, CAP & ADAPTER 1250 N.S., 1360,1850,1962(Bottle sits in black plastic receptacle on side of water frame)

1 Quart assembly P-1912 18.002 Quart assembly P-1921 59.80

BOTTLE, CAP & ADAPTER 1250 O.S.(Bottle sits directly in water fountain)

1 Quart assembly P-1911 19.802 Quart assembly P-1920 59.80

(A) WATER DUCTOR PIVOT - 1250 N.S., LW (11X17)

3/8” Bore P-12322 19.90

(A) WATER DUCTOR PIVOT - 1250 O.S. (10 X 15)

7/16” Bore P-12535 29.90

SCREW - O.S. & N.S. P-84 .60

(B) EQUALIZER PIVOT - 1330, 1360P-13322 29.90

(C) PIVOT HOUSING ASSEMBLY - 1330, 1360P-13535 37.50

DRIVE DISC For water form rollerP-12419 14.90

PIN ASSEMBLY For water fountain roller

Short 1-7/8” shaft P-12688 9.90Medium 2-1/8” shaft P-12687 9.90Long 3-3/16” shaft P-12691 9.90

COLLAR (For pin assembly listed above)1/2” for short pin P-12371 20.507/8” for long/medium pin P-12370 12.00

SHAFT For water fountain rollerP-12402 14.00

DRIVE COLLAR For Water fountain roller••• Made of steel for longer life.For non-operators side P-12417 12.50

SCREW P-840 5.90

PAWL - Water / Ink ratchet P-12268 16.00(A) 1250

PAWL - Water / Ink ratchet(B) 1330, 1360, 1650, 1850, 1960

P-13268 34.90

RETAINER For water oscillating roller

(A) Hex cap nut P-470 .60(B) Thumb nut P-538 2.20(C) Spring P-12413 1.50(D) Retainer P-12560 13.00(E) Stud (stem) P-7053 9.90

BEARINGS For “Multi Flow” Water oscillator.

Operators side P-5770 25.50Non-operators side P-5775 32.50

BEARING SHIELD (need 2)

For lower ink form roller on 1820 second color headP-1820000 6.00

FORM ROLLER KNOBSUpper ink form P-12489 29.90Lower ink form P-12491 29.90Water form P-12405 36.90

SET SCREW (all knobs) P-8 .60

SEPARATING CAM For ink form roller1250 O.S. (10 X 15) P-12864 39.901250 N.S. (11 X 17) P-12451 6.40TAPER PIN O.S. P-441 .60TAPER PIN N.S. P-439 .60

C

B

A

A

B

A

B

E

C

D

PART # PART #



INK IDLER GEAR - Bushing included1250 O.S. (10 X 15) P-12455 34.001250 N.S. (11 X 17) P-12446 32.50

BUSHING P-1236 1.60

INK IDLER GEAR - Does not use bushing.

1360, 1650 P-13457 72.00

DOG For oscillating rollers(A) Water P-12428 27.40(B) Ink P-12463 32.00

WORM For ink & water oscillating rollersP-12464 45.90

HOLD DOWN SCREW P-12494 1.60

IDLER ROLLER BUSHING - 1650P-11411 3.80

ROLLER SUPPORT1330, 1360 P-13915 10.50

INK & WATER DUCTOR ARM1250 N.S. (steel) P-12321 24.90INK & WATER DUCTOR LATCH1250 N.S. P-12338 5.50

1) INK & WATER DUCTOR ARM1250 O.S. (Brass) P-12607 30.00

2) INK DUCTOR LATCH No bend1250 O.S. (LH. & R.H.) P-12546 8.001850 P-18546 14.90

3) INK DUCTOR LATCH - With bend1250 W (R.H.) P-14546 9.901250 W (L.H.) P-14338 9.90

4) RIGHT HAND SPRING - Ink & water ductor latch1250 O.S. (10 X 15) P-12575 3.901250 N.S. (11 X 17) P-12336 1.70

5) LEFT HAND SPRING - Ink & water ductor latch1250 O.S. (10 X 15) P-12551 4.001250 N.S. (11 X 17) P-12331 1.50

INK & WATER RATCHET WHEEL1250, 1850 P-12239 29.901960 P-19239 57.50SNUBBER - Ink & water ratchet lever

P-7058 7.50

INK FOUNTAIN ASSEMBLY - 1250 O.S. & N.S.••• Designed with replaceable end caps & deeper well for 50% more ink capacity.Complete P-12778 319.80Fountain only P-12789 180.00Thumb screw (14 total) P-1570 6.00Wire P-35084 2.50Clamp P-12082 30.00Screw for clamp P-12907 3.40Blade 1250 (10-1/4” X 1-3/4”) P-12079 44.00Blade 1250 (10-1/4” X 3”) P-12233 70.00

INK FOUNTAIN BLADE1650 P-16233 108.001960 P-19079 99.90Blade 1850 only P-18079 69.90

A B

1

2

3

4

5

COMPOUND PULLEY P-4259 65.00

CLUTCH WEIGHT - 1360P-13593 5.80

CLUTCH PULLEY ASSEMBLY

Complete 1250 P-14001 259.90Complete 1850 P-18001 259.90(A) Pulley only 1250 P-12587 119.90(A) Pulley only 1850 P-18587 119.90(B) Clutch shoe (set of 4) P-12593 59.90(C) Spring P-12591 3.10(D) Liner P-5061 2.00(E) Clutch drum 1250 P-12617 72.90(E) Clutch drum 1850 P-18617 72.90(F) Pilot screw P-7069 6.90

INK WASH UP ATTACHMENT••• Universal for old & new style.

1250 O.S., W, LW (10 X 15 & 11 X 17) P-12773 256.00

WASH UP BLADE P-5030 9.90*Fits our wash up attachment only.

OLD STYLE DRIVE SHAFT ASSEMBLYComplete P-12835 128.00(A) Pinion gear - (black-stamped “O”) P-12854 34.00(B) Taper pin P-435 .80(C) Drive shaft P-12869 94.90

Complete P-12837 128.00(A) Pinion gear - (silver) P-12865 34.00(B) Taper pin P-435 .80(C) Drive shaft (only) P-12869 94.90

PILOT SCREW For pulley - both styles P-8068 5.90

NEW STYLE DRIVE SHAFT ASSEMBLYWith long shank gear. For use with hardened cylinder gears.

Complete P-12577 102.00(A) New style gear P-12581 32.00(B) Taper pin P-435 .80(C) Drive shaft P-12583 69.00

PILOT SCREW For pulley P-8067 5.90

DRIVE SHAFT ASSEMBLY - 1360, 1650Complete P-13837 189.90(A) Pinion gear P-13581 24.90(B) Taper pin P-435 .80(C) Drive shaft P-13869 172.00

A B C

A B C


PART # PART #

12

2650, 2850, 4150, 4250, 1330, 1360, 1315CD, 1650, 1820, 1860, 1870, 1960

SWITCH ASSEMBLYComplete P-12566 189.90

Start (green) 1250 N.S. P-12829 55.00Stop (red) 1250 N.S. P-4062 58.90

SWITCH REPLACEMENT KIT 1330, 1360

Consists of: 1 ea. stop switch (red) & start switch (green),1 mounting plate, 2 switch holders, 10 wire terminals.Also includes installation instructions.

P-9828 109.80

ALTERNATE ACTION SWITCH1960 P-4060 72.50

PUMP SWITCH1330, 1360 P-4470 24.90

(1) TOGGLE SWITCH For drive motor & pump (includes screws)1250 O.S. P-12305 77.90

WIRE MOUNTING SCREWS For P-123051250 O.S. P-252 .60

(2) MOMENTARY TOGGLE SWITCH1250 L.W. P-4056 30.00

COUNTERWith bracket & arm P-12996 124.90With bracket & no arm P-12954 99.90Counter only 1250N, 1360 P-12952 169.90

COUNTER ARM ONLY P-12942 29.90

“QUICK CHANGE” UPPER EJECTOR ROLLER ASSEMBLY••• Adjustable, gear driven with a knurled shaft for quick removal and easy access.

Complete 1250 N.S. P-12616 314.90(A) Rod assembly P-12558 128.00(B) Spring P-12604 1.60(C) Arm assembly L.H. & R.H. P-12584 29.90(D) Arm assembly R.H. P-12612 38.00(E) Roll assembly P-12600 29.90(F) Roller P-1444 4.20(G) Arm assembly L.H. P-12611 38.00(H) Roller P-12621 16.00(I) Shaft & gear assembly P-12782 75.00(J ) Wheel P-12590 9.90(K)Spring P-12618 4.90

STRIPPER FINGER - 1650 CD (1615)

P-162281 5.90

BACK JOGGER LEVER ASSEMBLY

1850 CD (1815) P-181590 59.90

1

2

B

K

AJ

I

H

G

F

E

D

C

GRIPPER BAR CHAINS

1250 (53-3/4” long X 1/2” wide) P-121100 26.901850 (54-1/4” long X 1/2” wide) P-181100 34.90Carrier link - 1250, 1850 P-9406 4.50

For Press Specialties chain delivery - N.S. (51-1/4” long X 1/2” wide) P-8944 66.00

For Press Specialties chain delivery - O.S. (50-3/4” long X 7/16” wide) P-8933 78.00

Gripper chain - TOKO 1218 P-8971 38.00Carrier link - TOKO 1218 P-8736 18.90

GRIPPER BAR ASSEMBLY(WITH BRASS COLORED ANVIL••• MADE OF YELLOW BRASS FOR HIGHER TENSIL STRENGTH.

Complete 1250 P-120990 340.00Complete 1330, 1360 P-130990 350.00Complete 1850 P-180990 490.00Complete 1960 P-190990 600.00(A) Finger P-121020 1.10(B) Screw P-12187 1.00(C) Holder P-121061 14.00(D) Spring P-121080 1.00(E) Anvil only 1250 P-121090 134.00(E) Anvil only 1330, 1360 P-131090 199.90(E) Anvil only 1850 P-181090 269.90(E) Anvil only 1960 P-191090 376.00(F) Screw P-44 .60(G) Locking collar P-734 10.70(H) Shaft assembly 1250, 1330, 1360 P-121010 69.90(H) Shaft assembly 1850 P-181010 79.90( I ) Stud P-4600 5.00(J ) Nut P-522 .60(K) Cam roller P-1447 6.90

GRIPPER BAR REPAIR KITConsists of the most commonly replaceable parts on your gripper bar assembly. (Less anvil & shaft) For Multilith style gripper bars only

1250, 1360 P-30733 105.90

GRIPPER BAR REPAIR KITS For Press Specialties Consists of the most commonly replaceable parts on your gripper bar assembly. (Less anvil & shaft where noted)

1217 (4 finger)* P-30745 248.001217, 1250 (5 finger)* P-30746 248.001250 (4 finger)** P-30747 248.001252 * P-30748 248.00

* does not come with shaft or anvil.** comes with shaft but no anvil.

••• ELIMINATE COSTLY DOWNTIME WITH YOUR OWN EMERGENCY KIT FOR YOUR MODEL PRESS.

REPAIR KITS FOR ALL MULTILITHS

Master kit P-1776 - 435 pcs. 359.80Junior kit P-30328 - 217 pcs. 199.90Nut kit P-1772 - 60 pcs. 44.80Screw kit P-1773 - 62 pcs. 159.80Pin kit P-1774 - 86 pcs. 52.90Spring kit P-1775 - 85 pcs. 139.80Washer & ring kit P-1777 - 136 pcs. 63.90

BA D G C

H FE

I J K

PART # PART #


Replacement parts for: RYOBI 2700, 2800, 3200, 3200AN/CD/NP, 3302M, 480/520/560

1) FILTER FELT P-30201 4.00

2) GASKET SEAL P-1937 6.70

3) WICK For oil jar P-1155 1.50

PUMP REPAIR KIT - 2700, 2800, 3200 P-31120 329.90

Consists of: 4 Vanes / 2 Filters / 1 Oil wick / 2 Ball bearings / 1 Oil seal

PUMP REPAIR KIT - 520/522/530/560P-31130 319.90

Consists of: 4 Vanes / 2 Filters / 2 Ball bearings / 1 Urethane gasket / 1 Fiber gasket / 8 Paper gaskets /2 Timing belts(Only one of each item depicted here)

PUMP VANE ••• MADE OF “GROUND STAINLESS STEEL”(27.5 mm x 115 mm) P-9448 69.90

TIMING BELT - For main pump520, 522, 530, 560

P-3811 34.90

VARIABLE SPEED PULLEYP-1491 249.90

SPEED CONTROL & FEEDER HAND CRANK••• Improved style works on 2700, 2800, 3200.

P-98060 31.90

HOSEFor side blowers P-5265 4.90For compressor filter P-5299 11.20For rear blower P-5288 7.00For sucker tube manifold P-1188 6.00

FEEDER CLAMP 5.5 mm slide plate slots P-27087 24.40 7 mm slide plate slots P-32087 24.40ADJUSTING SCREW P-2652 9.90

SLIDE PLATE For feeder clamp5 mm slide thickness P-27089 49.906.5 mm slide thickness P-32089 56.90

SLIDE PLATE & FEEDER CLAMP KITP-39087 83.80

BUMPER For air control latch P-5283 3.20

HEIGHT CONTROL SCREW - For paper leveling bar.P-8144 15.90

COUPLING JOINT P-6776 12.10

SUCKER TUBE P-27174 12.50

SCREW HOLDER P-27966 9.10

1 2

3

slide thickness

SUCKER FEETStandard P-5208 .80••• Treated with ink resistant repellent for less ink tracking.

SUCKER FEET

(A) 500K, 512 P-5241 7.00(B) 480N, 480K P-7580 4.60

SHEET SEPARATORBrass P-27114 1.00Copper P-27117 1.20

SHEET SEPARATORS(A) 522 P-522114 3.00(B) 522PF / PFH P-522114PF 10.90

THUMB SCREW For sheet separator bracketP-2909 4.20

THUMB SCREW For master cylinder tail clamp 2700, 2800, 3200 P-2903 8.90

GUIDE SPRING975 PFA P-97471 6.50(Thick) P-33478 10.90(Thin) P-33471 14.00

BACK PAPER GUIDE ASSEMBLY 2700, 2800, 3200, 3200MCDCOMPLETE P-27081 71.90(A) Screw w/ sems washer P-2328 .60(B) Block P-27221 10.80(C) Bracket P-27090 34.90(D) Back guide spring P-27712 25.80(E) Screw P-2327 .60

SPRING BASE For P-27088 shown below.

P-27100 33.90

1) BACK PAPER GUIDE P-27537 9.90

2) SIDE PAPER GUIDE P-27088 10.50

PAPER RETAINER - 3302Located under upper feed roller.

P-33143 26.90

PAPER GUIDE HANDLE STOPPER950, 960 P-95124 14.90

PAPER RETAINERFeeder 3302 P-33500 22.50Conveyor .008 thick P-33420 23.90Conveyor .012 thick P-33433 22.50

FEED TAPES (sold individually—not in sets)480K/N, 500N/NP P-3935 39.903302 s/n up to 4432 P-3939 32.003302 s/n 4433 to 7036 P-3936 32.003302 s/n 7037 & Up P-3870 39.90

FEED SENSING SWITCHR-3302, I-3985 P-4050 29.90

A&BE

D

C

1

2


PART # PART #

14

ITEK 530, 560, 950, 960, 975.....................................................Continued thru page 16.

FEELER FINGER SHAFTComplete 2700, 2800 P-27138 99.90Complete 3200 P-32138 169.90(A) Shaft only 2700, 2800 P-27139 62.90(A) Shaft only 3200 P-32139 115.90(B) Lever P-27719 19.00(C) Latch P-27141 29.90(D) Roll pin P-2834 .60

RUBBER FEED ROLLERS2700, 2800 P-27157 179.903200 P-32157 179.90

IMP. GRIPPER FINGER1) 2700, 2800, 3200 P-27245 8.002) 3302 (urethane tip) P-33245 14.90

PAPER STOP FINGER1) 2700, 2800 P-27241 6.002) 3302 P-33241 9.90

FEED DRUM FINGER P-33237 19.00(urethane tip)

SKID ROLLER ASSEMBLY - 3302Operators side (shown) P-33562 134.90Non-operators side P-33568 134.90

SPRING - Imp. cyl. latch P-27791 9.50

ADJUSTING NUT For blanket cylinder clampsRight hand thread P-5303 25.80Left hand thread P-5312 25.80

STANDARD BLANKET BARS2700, 2800 Complete P-27252 220.00R-3200, I-975 Complete P-32252 222.00R-3302, I-3985 P-33252 167.90(A) Upper blanket bar 2700, 2800 P-27258 71.90(A) Upper blanket bar R-3200, I-975 P-32258 54.00(A) Upper blanket bar R-3302, I-3985 P-33258 82.00(B) Lower blanket bar 2700, 2800 P-27256 65.90(B) Lower blanket bar R-3200, I-975 P-32256 62.00(B) Lower blanket bars R-3302, I-3985 P-33256 78.90(C) Mounting screw P-2216 .60(D) Clamping screw P-2206 .60

QUICK CHANGE BLANKET BARS••• Bars remain on your cylinder while you make a 5 minute blanket change.

Closed cylinder 1/2” gap (19” blanket size) 950, 960 / 2700, 2800 P-30310 210.00Open cylinder 4” gap (19-1/2” blanket size)2700XL, 2800XL P-30047 341.25975 / 3200 P-30037 193.05985 / 3200 MCD P-30038 209.65975 / 3200XL,XLD,CPD P-30311 341.253985 / 3302 P-30221 390.00

B

D

A

D

C

1

2

A

B

C D

TAIL CLAMP SPRING P-27327 9.90

LATERAL ADJUSTING SCREW For head clampP-2917 13.90

SPRING (Plate Cylinder) P-33365 4.90

TAIL CLAMP2700, 2800 P-27323 105.803200 CD/NP P-32323 116.903200 17-1/4” IMAGE P-32333 110.003302 P-33323 97.50

LOCK PIN on Plate CylinderP-4543 29.90

HEAD CLAMPS For Ryobi 3302••• DIAMOND COATED FOR SURE GRIP AND LONGER LIFE.Top bar (shown) P-33788 490.00Short clamp (Operators side) P-33771 162.50Short clamp (Non-operators side) P-33760 162.50

PIN For P-33788 shown above.Ser. # 6186 & lower (3mm small O.D.) P-4773 7.00Ser. # 6187 & higher (5mm small O.D.) P-4789 4.90

WATER CONTROL LEVER

3200 MCD P-320416 32.00

WAVER ROLLER TENSION SPRINGP-38413 4.90

WATER OSCILLATOR SHAFT ASSEMBLY - 2700, 2800Complete P-27460 299.90Shaft only P-27460-S 184.90Dog P-27463 44.00Worm P-27464 63.80Roll pin P-382 .60

SPLASH GUARD SHIELD P-27376 3.00

SPLASH GUARD KIT P-27376-K 22.90Consists of 2 shields plus hardware.

WATER BOTTLE STOP P-7621 8.20SPRING for cap assy. P-27543 4.90

BEARING HOUSING P-27322 66.90

WATER DUCTOR LATCH2700, 2800 P-27546 6.00

PART # PART #


Replacement parts for: RYOBI / ITEK...................................Continued from page 13.

WATER FOUNTAIN ROLLERS2700 P-27364 204.003200 P-32364 390.00

INK WASH UP BLADE

950, 960, 2800 - 30.3 cm Long (6 Holes) P-30224 14.903200, 3302, 3985 - 35.9 cm Long (6 Holes) P-30225 14.90

INK FOUNTAIN BLADES

2700, 950 - 29.5 cm x 9.0 cm (Ser.16331 & up) P-27233 77.902700, 950 - 28.6 cm x 7.0 cm (Ser.16330 & down) P-95233 82.903200 CD/NP - 32.0 cm x 9.0 cm P-32233 89.903200 MCD/MNP- 34.6 cm x 9.0 cm P-32233M 86.00500N / NP - 49.2 cm x 85.7 cm P-50079NP 79.00

WASH UP TRAY ASSEMBLY

2700/2800 P-27773 219.903200/3202 P-32773 169.903302 P-33773 289.90

INK FOUNTAIN WIRE950, 960, 2700, 2800 P-37084 2.903200, 3302 P-32084 1.70

BUSHING For ink fountain rollerP-3268 9.90

INK IDLER GEAR P-27509 144.90

INK DUCTOR ARMS

(A) I-950/960 P-95607 43.90

(B) R-27/28/3200 Sers. P-27607 43.90

INK DUCTOR SPRINGSOperators side P-27338 3.50Non-operators side P-27336 2.40

INK RATCHET PAWL P-27268 39.80

BUSHING For idler rollers P-3207 24.90

ADJUSTING SCREW For ink fountain

ITEK 950, 960 P-2021 5.20

ADJUSTING SCREW For ink fountain

R-2700, 2800, 3200, 3302 P-2925 7.00

OSCILLATING SHAFT ASSEMBLY - INK 2700

Complete P-27462 204.90Shaft only P-27472 73.80Roll pin P-2834 .60Dog (comes with P-27249) P-27463 44.00Worm (comes with P-27249) P-28464 63.80

Dog & Worm set P-27249 94.00

DOG & WORM KIT P-27874 94.00DOG (Ink & Water 950, 2700) P-27463 44.00WORM (Ink & Water 950, 2700) P-27464 63.80

DOG (Ink & Water 960, 2800) P-27463 44.00WORM (Ink 960, 2800) P-27464 63.80WORM (Water 960, 2800) P-28464 63.80

BUSHING For ink oscillating rollerP-3203 14.00

KEY For drive shaft clutch pulleyP-11652 2.00

DRIVE SHAFT AND GEAR ASSEMBLY

Complete 2700, 2800 P-27577 289.90Complete 3200 P-32577 340.00Complete 3302 P-33577 243.90Shaft only 2700, 2800 P-27583 143.90Shaft only 3200 P-32583 170.00Shaft only 960PFA, 3200PFA P-32583PFA 199.90Shaft only 3302 P-33583 110.00Gear only 2700, 2800, 3200 (not 3200PFA) P-27581 104.90Gear only 3302 P-33581 110.00Taper pin 2700, 2800, 3200 P-451 .60Taper pin 3302 P-2849 2.00

COUNTER P-27954 129.00

Screw P-2521 .60Washer P-2700 .60Arm P-27956 26.00

IDLER GEARSOn ejector roller P-27636 57.90

For C/D drive sprocket shaftP-27629 57.90

GEAR STUD For Chain Delivery drive gear

P-7939 16.00

SWITCH BODY For control panel

R-3302, I-3985 P-9830 39.90


PART # PART #

16

Replacement parts for: RYOBI / ITEK...................................Continued from page 13.

OFFSET DUPLICATOR LAMP (Long neck)

950, 960, 2700, 2800 P-9865 99.80

Lamp comes with plug and can be plugged into any standard 115v wall outlet. Some models of Ryobi may need lamp wired directly to press.

••• CAN USE UP TO 100 WATT BULB.

LED LAMP - On sub control box.R-3302, I-3985 P-9707 30.00

CARRIER LINKFor gripper bar P-8738 14.00

GRIPPER CHAIN (1 only)59” long P-8939 100.0054” long P-8938 160.00NOTE: Please measure your chains end to end.

Chain connecting link P-1540 2.90

CONNECTING LINK

R-3302, 3304 / I-3985 P-8745 22.50

GRIPPER BAR ASSEMBLY

Complete 2700, 2800 P-270990 439.90Complete 3200 P-320990 399.90Complete 3302 P-330990 495.00

(A) Right hand bracket P-320991 52.90(B1) Taper pin P-2810 .90(B2) Taper pin P-2805 .60(C) Gripper arm P-271040 29.90(D) Roll pin P-2832 .60(E) Screw P-2103 .60(F) Gripper finger (no urethane) P-271020 11.50(F) Gripper finger (urethane tip) P-331020 38.85(G) Spring (2 on 2700, 2800, 3200) P-281080 2.30(G) Spring (4 on 3302) P-331080 2.90(H) Set screw P-2511 .60(I) Collar P-1487 9.90(J) Gripper finger shaft - 2700, 2800 P-271060 12.40(J) Gripper finger shaft - 3200 P-321060 10.90(K) Center bracket P-271092 21.90(L) Left hand bracket P-320992 52.90(M) Ball bearing P-1803 6.50(N) C-Ring P-2752 .60(O) Lockwasher P-2702 .60(P) Nut P-2602 .60(Q) Stud P-7920 6.30(R) Roll pin P-2833 .60(S) Gripper pad P-271061 6.40(T) Shaft - 2700, 2800 P-271091 31.90(T) Shaft - 3200 P-321091 34.90(U) Collar P-11435 5.70

BACK STOP BRACKET (Chain Delivery)

2700, 2800, 3200 P-272422 29.90

JK

AN M

O&P&QS

RT

B1 CD

E F GH

IU B2

L

GUIDE P-272281 22.00

FRONT GUIDE P-272420 83.90

DELIVERY TABLE SENSING SWITCH

R-3200, I-975 P-9815 18.90

V-BELT For Ryobi / ItekFor compressor P-1678 (28”) 8.00For clutch pulley P-1687 (31”) 8.00Motor to pump P-1695 (34”) 7.50Motor to pump 3202M P-4905 (36”) 9.90Motor to pump 950, 960 P-4907 (38”) 9.00Drive motor 3200 (60Hz) P-4910 (42”) 10.50Drive motor 3200 (50Hz) P-4986 (41”) 16.00••• All sizes available 2L, 3L, 4L, 5L

DOLLY BOARD ASSEMBLY - RYOBI 3302Complete P-332440 214.00Board only P-332500 174.50Caster P-1641-S 19.90Washer P-569 .60Screw P-10342 .60

••• Eliminate costly downtime with your own emergency kit for your model press.(Master Kit does not include Spring Kit)REPAIR KITS FOR RYOBIMaster kit P-30376 - 513 pcs 239.80Pin kit P-30375 - 168 pcs. 99.90Ring kit P-30374 - 104 pcs. 55.80Nut kit P-30373 - 38 pcs. 21.80Washer kit P-30372 - 68 pcs. 49.90Screw kit P-30371 - 132 pcs. 77.90Spring kit P-31128 - 39 pcs. 129.90

• • • • • • • • • PARTS FOR ITEK • • • • • • • •GEAR- For 1015/1117 Plate Maker

Tank roller frame ass’y. P-1015010 7.50

GEAR- For 1015/1117 Plate Maker








SPRING- For 1015/1117 Plate Maker

Tension rollers P-1015200 3.90

SPRING- For 1015/1117 Plate Maker

Tension rollers P-1015210 6.90

PART # PART #


Replacement parts for: TOWNSEND-51 second color heads

T-WRENCH T-1132 27.90

END BELLSmall T-1807 33.50Large with hole for dog T-4806 35.90

DRIVE PULLEY T-22444 79.90

TIMING BELT For the AB Dick seriesP-1654 10.50

INK RATCHET DRIVE ARM Fits all modelsT-1551 12.90

PINION GEAR T-24435 46.90

LOCKING SCREW For 1250W & LWT-1116 11.90

MICRO SCREW T-7153 19.90

DOG1250 O.S., 350, 360, O.S. T-1804 29.901250 N.S., 350, 360, N.S. T-4804 29.90WORM T-1802 29.90

INK & WATER HOLD DOWN ASSEMBLYSmall - water for AB Dick 350, 360 N.S.L.H. T-4858 39.90R.H. T-4857 39.90Large - ink for Multilith 1250 N.S., 350, 360 N.S.L.H. T-2855 34.90R.H. T-2856 36.00

SHAFT (Ink oscillator) AB Dick 9800 T-19801 27.90SHAFT (Small ink oscillator) Multilith 1250 T-1801 36.90SHAFT (Small ink oscillator) AB Dick 350, 360 T-2801 22.60SHAFT Torsion rod for cylinder assembly - - Ryobi 2700, 2800 / Itek 950, 960 T-18119 25.90

COLLAR ASSEMBLY Water bottleComplete T-3643 9.00Collar only T-3637 9.00Thumb screw P-309 .60

HOSE Water fountain P-1189 1.80TUBE CONTROL VALVE P-11934 3.00

DRIVER ASSEMBLYComplete T-20652 54.90Clutch only T-20653 34.90One way clutch bearing P-5800 29.90

TRANSFER BUSHING ASSEMBLYRyobi, M-1250, A-9800 T-7827 34.90Multi T-1827 35.90A-9800 (Geared trans.) T-19824 34.90A-9800 (Non-geared) T-19827 34.90

TRANSFER DRIVE GEAR T-22433 54.90

RATCHET PAWLInk (oper. side) T-1570 14.00Spring (oper. side) T-1572 3.90Water (non-oper. side) T-1571 14.00Spring (non-oper. side) T-1573 3.90

DUCTOR ARM Ink & water T-1503 21.00

LATCH Ink & water T-1504 6.50

DUCTOR LATCH SPRING Ink & waterNon-oper. side (L.H.) P-12575 3.90Oper. side (R.H.) P-12551 4.00

FORM ROLLER DRIVE GEAR & PINION ASSEMBLY1250 Old style (10 X 15) T-1407 62.901250 Old style (11 X 17) T-2407 66.901250 New style (11 X 17) T-4407 77.90360, 375, 9800 T-8407 77.90

Drive pinion only (comes with gear but is sold separately)T-1403 33.90

INK FOUNTAIN BLADEFor Ryobi 2800, AB Dick 350, 360, Chief 15, 17 T-2627 22.00Screw (need 5) P-120 .60

OSCILLATING ROLLER TUBE

AB Dick 350, 360, Multilith 1250 N.S.(Large ink) T-2810 129.90(Small ink) T-2811 119.90

AB Dick 350, 360 O.S.Complete ass’y. (small ink) T-2824 299.90

AB Dick 9800 O.S. & NS.& Multilith 1330, 1360 T-18811 117.90

Chief 15, 17(Small ink) T-12811 149.90

Multilith 1250 O.S.(Small ink) T-1811 139.90

EQUALIZER BAR For ink & water ductor AB Dick 350, 360, Ryobi 2700, 2800, Multilith 1250 N.S., Chief 15

P-15340 24.90

MICRO CLAMP1-3/16” O.A.L. T-7151 27.907/8” O.A.L. T-4176 57.00

KNOBFor water fountain roller T-22611 13.90

CYLINDER BRACKET LOCK SCREW For

A.B. Dick 350/360 N.S., 8800, 375, 9800, 385Multi 1250LW, 1330, 1360, 1850Ryobi/Itek 2700, 2800, 3200, 950, 960, 975

T-9719 8.30


PART # PART #

18

Replacement parts for: HAMADA 500CDA, 600CD, 600AT, 601CD/QT, 602CD/QT, 611,

PUMP VANE P-9446 26.20

PUMP REPAIR KIT P-31125 249.90Consists of: 8 Vanes - #P-9446 / 4 Bearings - #P-790 /1 Bottle of pump oil - #P-1588

V-BELTS For HamadaFor compressor (115V, 50/60 Hz)

P-1680 (27”) 6.00For compound pulley to machine P-1686 (30”) 6.50Intermediate P-4930 (36”) 12.50Drive shaft (60 Hz) P-1678 (28”) 8.00Main drive P-4933 (39”) 12.50Main drive P-4934 (38”) 12.50Main drive P-5457 (37”) 11.90••• All sizes available 2L, 3L, 4L, 5L

SPEED PULLEY

P-9350 548.00

BUSHING For rotary valve flange.P-3275 17.80

SUCKER FOOT(A) Standard (500, 700) P-5207 2.60(B) Heavy (500, 700) P-5205 2.00(C) For 611, 248, 234 Duetto, E47 P-5206 2.20(D) Hamada Bellows P-7575 2.25

(C&D not shown)

SUCKER FOOT HOLDER P-55174 7.00For P-5207 / P-5205 Listed above.

FEED BRUSH P-31170 14.90

FEEDER CLAMP P-55049 28.80

FEEDER CLAMP - 611, 612P-66087 67.90

FEEDER PULLOUT ROLLER500, 700 P-55125 21.55600, 601, 602, 800 P-66125 90.00

SPRING For feed roll tire P-55386 2.90

SLEEVE For inside of pullout roller bearingP-55384 18.00

BEARING ASSEMBLY For lower feed roller(500 PF)Only P-3201 28.90

BUSHING For lower feed roller500, 600, 700, 800 P-3286 12.90

A

B

SHEET SEPARATOR P-12114 .90

BRACKET For sheet separator holder

P-55113 16.00

THUMB SCREW For sheet separator holder

P-2900 5.20

TABLE RAISE HANDLE ASSEMBLY••• MADE WITH DURABLE WHITE BRASS FOR LONGER LIFE & DURABILITY.

Complete P-12955 140.00(A) Screw P-874 .60(B) Nut P-492 .60(C) Ball (inside) P-755 1.90(D) Spring (inside E) P-12909 2.50(E) Handle P-36961 24.90(F) Shaft P-36962 19.90(G) Spring lock P-36959 2.40

BLOCK For blower nozzle P-55164 11.90

SPRING For paper feed adjusting shaft

P-55148 2.50

HEIGHT CONTROL LEVERP-55782 24.90

SPRING For paper height bar700 P-77711 3.70

CONVEYOR TAPE P-1796 12.50

PAPER RETAINER P-12433 19.90

CONVEYOR JOGGER BLOCKP-55200 9.90

JOGGER CAM LINK P-55443 19.90

SPRING For conveyor spring guide

800DX, SX P-80496 2.50

FEED ADJ. KNOB P-11541 12.90

STOP For adjusting nut P-12606 6.00

IMPROVED

EF

A&B

PART # PART #


612,700CD, 800DX/SX, 50/60/70/80..................................Continued thru page 20.

SHAFT For clutch pulley P-55614 18.90

FEELER FINGER P-55141 12.90

SPRINGS For impression cylinder shaft

(A) P-55213 5.00(B) P-55406 3.20

IMPRESSION GRIPPER FINGER

P-55245 3.90

COUNTER ASSEMBLY P-55954 91.90

BLOCK For blanket bar P-55922 46.50

BRACKET NUT For blanket cylinder.

P-55361 69.00

(A) SHAFT - Master cylinder gear lock. 500, 500CD P-55180 64.00 500CDA, 600CDA P-66180 32.00 700CD P-77180 35.90

(B) NUT For gear lock shaft. P-55186 4.20(C) SHAFT KEY P-55182 2.90(D) WRENCH P-5883 23.90

MASTER CYLINDER CLAMP ADJUSTMENT

Thumb screw P-2922 14.80Thumb nut P-2942 15.60

DRIVE SHAFT GEAR P-55581 61.90

WATER STOP P-30220 4.40

GEAR For dampening form rollerP-55046 72.00

WATER PAWL P-55462 10.00

WATER PAWL SPRING P-55267 1.20

A

B

DOG & WORM (Water) P-55429 60.00DOG (500, 600, 700) P-55428 29.90WORM (Ink & water 500, 600, 700)

P-55464 43.90DOG (8MM Thick head) (Ink 500, 600, 700)

P-55463 29.00WORM (Ink & water 500, 600, 700)

P-55464 43.90

•••Hardness density has been improved so that the dog and worm wear evenly.

INK DOG & WORM KIT P-55874 59.80

Consists of dog, worm, and pin for worm.

DRIVE DOG (9MM Thick head) For second color unitP-5525463 29.90

WATER DUCTOR ARMS14MM Bore (L.H.) P-7727607 32.0014MM Bore (R.H.) P-7727321 32.0012MM Bore (L.H.) P-5525607 31.9012MM Bore (R.H.) P-5525321 44.00

LATCH For form roll handle P-55538 16.90

FORM ROLLER DRIVE DISC800DX / SX P-80419 48.90

FORM ROLLER HUBP-55411 21.90

SPRING Between ink form roller bracketsP-55475 1.80

INK DUCTOR ARM P-55572 16.90

EQUALIZER BAR For ink ductor assembly. P-55550 45.00

IDLER GEAR (BRASS) For night latch P-55457 99.90

IDLER GEAR (STEEL)Contacts distributor roller P-55446 69.90

DUCTOR ROLLER LATCH Ink P-55338 5.20 Water P-55546 5.80

DUCTOR ROLLER SPRINGS Non operators side P-55331 2.40 Operators side P-55336 2.40

DUCTOR SHAFT SPRINGSR.H. 500, 600, 700 P-55549 1.80L.H. 500, 600, 700 P-55567 1.80

PILOT SCREW For ink & water ratchetP-6509 4.90

IMPROVED


PART # PART #

20

Replacement parts for HAMADA..........................................Continued from page 18.

GRIPPER BAR ASSEMBLYComplete 500CDA, 600 P-550990 290.00Complete 800DX, 800SX P-800990 338.00(A) Anvil (500CDA, 600) P-551090 159.00(A) Anvil (800) P-801090 199.90(B) Shaft (500CDA, 600) P-551060 32.00(B) Shaft (800) P-801060 54.00(C) Gripper spring (500 uses 4 / 800 uses 8) P-551080 2.40(D) Roll pin (500 uses 4 / 800 uses 8) P-2832 .60(E) Gripper finger (500 uses 4, 800 uses 8) P-551000 7.90(F) Gripper tension spring (1 for 800 only) P-771080 2.00(G) Set screw P-2506 .60(H) Collar (500 use 1 / 800 uses 3) P-6728 4.00

** Lever assembly (consists of items (I) - (P) P-551040 49.90(I) Gripper operating lever P-551041 29.90(J) Screw P-2107 .60(K) Lockwasher P-2701 .60(L) Nut P-2602 .60(M) Lockwasher P-631 .60(N) Washer P-2729 .60(O) Ball bearing P-1803 6.50(P) Shoulder screw P-8160 7.90

GRIPPER BAR REPAIR KITS

H-500CDA, 600 P-30741 240.00 Enough parts to rebuild 3 gripper bars. Consists of key #’s: C (qty. 12), D (qty. 12), E (qty. 12), G (qty. 3), H (qty. 3), J (qty. 6), K (qty. 6), P-551040 Lever assy. (qty. 3).

H-800 P-30743 144.90 Enough parts to rebuild 1 gripper bar. Consists of key #’s: C (qty. 8), D (qty. 8), E (qty. 8), F (qty. 1) G (qty. 2), H (qty. 2), J (qty. 1), K (qty. 3), P-551040 Lever assy. (qty. 1).

GRIPPER BAR ASSEMBLYComplete 700CD P-770990 359.90(A) Anvil P-771090 259.90(B) Shaft P-771060 42.00(C) Screw P-2107 .60(D) Gripper finger (use 7) P-661020 9.90(E) Set screw (use 3) P-2506 .60(F) Collar P-6728 4.00(G) Gripper spring (on operators side use 1) P-551081 2.40(H) Gripper spring (on non-operators side use 1) P-771080 2.00

** Lever assembly (consists of items (I) - (P) P-551040 49.90(I) Gripper operating lever P-551041 29.90(J) Screw P-2107 .60(K) Lockwasher P-2701 .60(L) Nut P-2602 .60(M) Lockwasher P-631 .60(N) Washer P-2729 .60(O) Ball bearing P-1803 6.50(P) Shoulder screw P-8160 7.90

GRIPPER BAR REPAIR KIT

H-700 P-30742 134.90 Enough parts to rebuild 1 gripper bar. Consists of key #’s: C (qty. 1), D (qty. 7), E (qty. 3), F (qty. 3), G (qty. 1), H (qty. 1), K (qty. 3), P-551040 Lever assy. (qty. 1).

A

BCD

E

FG&HI

J

K

A

BC

D

E&FG&H

I

J

K

GRIPPER FINGER P-551000 7.90

GRIPPER FINGER (with pin) P-801024 29.50GRIPPER FINGER (w/o pin) P-801025 23.20

CHAINS -500, 600, 800 P-8937 124.00 -700 (delivery-set of 2) P-8936 124.00 -(side jogger 1 only) P-8908 17.80

GRIPPER CHAIN -601, 602CD/QT (1 only) P-8958 69.00 - RS34, VS34, H234 P-8995 49.90

CHAIN JOINT ASSEMBLY -Carrier link P-5345 7.50

CLEAN UP BLADES500,600,660/62/65 . .12-5/8 x 1-3/4 — (9) [R] P-30214 39.90800 SX/DX . . . . . . . .21-3/16 x 1-3/16 — (14) [R] P-30215 46.95611, 612 . . . . . . . . . .13-5/16 x 1-3/4 — (9) [R] P-30204 25.95660 2nd. head . . . . .12-3/8 x 1-1/2 — (8) [SR] P-30213 25.95500 2nd. head . . . . .12-5/8 x 1-9/16 — (9) [SR] P-30306 49.90700 1st. head . . . . . .19-1/4 x 1-7/8 — (13) [R] P-30248 41.95700 2nd. head . . . . . .18-31/32 x 1-9/16 — (13) [SR] P-30223 41.95880 2nd. head . . . . .21-3/16 x 1-19/32 — (14) [SR] P-30206 46.95RS, VS34 . . . . . . . . .13-7/8 x 1-5/16 — (5) [SR] P-31300 25.95VS, RS34, H234 . . . .14-1/16 x 1-5/8 — (5) [SR] P-31306 25.95C248 . . . . . . . . . . . . .20-1/4 x 1-13/16 — (14) [SR] P-30250 32.00

*** Numbers in ( ) indicate number of holes or slots on blade.*** Letters in [ ] indicate Plastic, Rubber, or Steel and Rubber blade material.

DELIVERY STRIPPER FINGER700 P-772282 6.00

STRIPPER FINGER800 P-802281 4.50

STRIPPER FINGER ASSEMBLY For chain deliveryComplete P-552280 49.90(A) Stripper only P-552281 5.50(B) Block only P-2482423 48.00(C) Screw P-2407 .60(D) Washer P-2701 .60

PAPER STRIPPER ASSEMBLY - For Hamada C248

Complete P-2482280C 84.90(A) Bracket P-2482423 48.00(B) Screw P-2408 .60(C) Screw P-2407 .60(D) Plate P-2482420 28.00(E) Paper stripper P-2482281C 9.50(F) Lockwasher P-2701 .60

••• Eliminate costly downtime with your own emergency kit for your model press.(Master Kit does not include spring kit)REPAIR KITS FOR HAMADAMaster kit P-30376 - 513 pcs. 239.80Junior kit P-31138 - 234 pcs. 179.80-Pin kit P-30375 - 168 pcs. 99.90-Ring kit P-30374 - 104 pcs. 55.80-Nut kit P-30373 - 38 pcs. 21.80-Washer kit P-30372 - 68 pcs. 49.90-Screw kit P-30371 - 132 pcs. 77.90-Spring kit P-31127 - 48 pcs. 69.80

C&D

B

A

B&F

A

D E

C

PART # PART #


Replacement parts for: HEIDELBERG..................................Continued thru page 31.

PUMP FILTER - Quickmaster 46

P-9470 31.20

SILENCER P-9413 65.00

RIBBED V-BELTS

TOK - Drive motor (610mm) P-3780 16.50TOK - Drive shaft (762mm) P-3783 36.50GTO 46 - Drive motor (1168mm) P-3785 57.00GTO 46 - 4 Color Drive Belt P-3733 69.00GTO 46/52 - Drive motor P-3716 41.00GTO 52 - Drive motor (1321mm) P-3788 98.80GTO 52 Z/P, V/P - Drive motor (1016mm) P-3790 89.90GTO 52 Z/P, V/P - Drive motor (1397mm) P-3791 69.50Windmill 10 X 15 - Main drive (2150 mm) P-3703 352.00Windmill 10 X 15 - Main drive P-3793 199.80Windmill 10 X 15 - Main drive (2362 mm) P-3893 154.90 Windmill 13 X 18 - Main drive P-3722 229.90

TIMING BELTS - TOKSTACK-LOAD MASTER FEED P-3810 19.00MASTER FEED TABLE P-1697 7.50

FEED TAPESPEEDMASTER 72 & 102 P-3918 34.60MO, SORK P-3927 19.00

SHEET SEPARATORS

(A) KORD (45°) HE-KØ114 7.00(B) KORD (45° with pad) HE-KØ420 10.90(C) KORD (90°) HE-KØ117 7.00(D) K-Series HE-KS117 11.90(E) K-Series w/hood HE-KS114 9.90(F) GTO 46 HE-46117 5.60(G) GTO 46 (with hood) HE-46114 6.00(H) GTO 52 HE-52117 9.90(I) GTO 52 (with hood) HE-52118 9.90(J) GTO 52 (45°) HE-52114 3.20(K) M/S Series HE-SØ117 24.90(L) M/S Series HE-SØ114 29.90(M) M/S Series HE-SØ106 33.90(N) SB Series (90°) HE-SB117 9.50(O) SB Series (45°) HE-SB114 9.50(P) WINDMILL HE-WI114 10.00(Q) WINDMILL HE-WI117 9.50(R) Quickmaster 46/46DI HE-46114QM 24.90(S) GTO (Operator side) HE-52106 53.40(T) SM52/74 (Operator side) HE-52106SM 64.90(U) GTO (Non-Operator side) HE-52107 53.40(V) SM52/74 (Non-Operator side) HE-52107SM 64.90(W) M/S/SM102 Brush HE-S0107 29.90

RUBBER HOOD For sheet separators.

HE-46114-R 4.90

SHEET SEPARATOR BARQUICKMASTER 46 & 46DI

HE-46117QM 224.90

PLATE SPRING For Quickmaster

4mm HE-46099QM-4mm 6.406mm HE-46099QM-6mm 11.00

SHEET STEADIER BRUSH - GTO 46 / 52, K-SeriesComplete HE-46403 82.00

Brush only HE-46420 6.00Wing nut P-3399 2.00Shoulder screw P-8176 9.90

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

SHEET SEPARATOR HOLDER

KOR HE-KØR113 34.00

SHEET SEPARATOR HOLDER - L.H. & R.H.••• UNIVERSAL. WORKS ON BOTH SIDES OF FEEDER.

KORA, KORD, KORS HE-KØRD113 28.90

BRUSH WHEELS For feeder section.

K, M, S, SPEEDMASTER (whtie bristle) HE-SR420 21.20K, M, S, SPEEDMASTERfor cardboard stock (black bristle) HE-SR500 24.00

FEED GRIPPER COMPLETE - GTO 46 & 52

COMPLETE HE-46511 899.90(A) Gripper finger HE-46212 12.00(B) Hex head screw P-2088 .60(C) Needle bearing P-3466 19.90(D) Cam roller P-6838 38.90(E) Flat washer P-595 .60(F) E-ring P-2759 .60(G) Stud-for cam roller P-7943 23.00(H) Taper pin P-431 .60(I) Connecting piece P-11923 9.90(J) Torsion spring HE-46212-T 3.00(K) Gripper pad not sold alone -------(L) Spring HE-46212-E 24.90(M) Grooved pin P-3037 .60(N) Torsion Spring (not shown) (see note) -------(O) Backing Plate HE-46212-BP .90

NOTE: Torsion spring “N” is obsolete. Spring “L” & grooved pin “M” are used in place of it.

SPRING For traveling feed gripper.

K-series HE-K0144 6.50

SUCKER FEET

(A) GTO (9/32 ID x 3/4 OD gum rubber - blue) P-5222 .90(A) GTO (9/32 ID x 3/4 OD polyurethane - red) P-7568 1.80(B) GTO (5/16 ID x 11/16 OD for cardboard) P-5244 1.75(C) HEIDELBERG/KLUGE (7/8” O.D.) P-5210 1.60(C) HEIDELBERG (1-1/16” O.D.) P-7556 1.20(D) HEIDELBERG (5/32” I.D. x 1” O.D.) P-5223 .80(D) WINDMILL (5/32” I.D. x 7/8” O.D.) P-7566 .60(D) WINDMILL (1/8” .ID. x 29/32 O.D.) P-5234 .70(E) SOR (1-1/4” O.D.) P-5236 .80(E) MO/SOR (1-3/16” O.D.) P-5240 .80(E) MO/SOR (1-1/2” O.D.) P-5243 1.00(E) Speedmaster 52 (6/16 I.D. x 1-3/16 O.D.) P-7564 .80(F) SORKZ For tissue paper P-5218 7.00(G) TOM/TOK (1-1/4 Long) P-5215 1.20(G) Quickmaster (11/16 Long) P-7558 .80

SPRING GUIDE (TONGUE) For conveyorK- series HE-KØR420 8.50

RETAINER SPRING For GTO 52 feeder.HE-SØ711 2.40

GRIPPER FINGERHE-46212

B

K I J

GD

FEC

L

MO

A B C D E F G


PART # PART #

22

Replacement parts for: HEIDELBERG .................................Continued thru page 31.

HOLDER ASSEMBLY - GTO 46/52, WINDMILL PLATENSComplete HE-WI434 59.80Replacement roll pin P-2839 .60Replacement thumb screw P-2022 3.90

SHEET STEADIER ASSEMBLY - GTO 46 / 52, K-SeriesComplete HE-KØØ27 81.90(A) Sheet steadier HE-KØR090 38.90(B) Holder HE-46049 35.90(C) Thumb screw P-2022 3.90

FRONT GUIDE - For GTO 46/52, K-Series

(A) Guide only HE-KØ383 39.90(B) Adjusting knob P-2932 24.10(C) Retainer spring HE-KØ257 5.50(D) Adjusting screw P-2912 19.90

SHEET STEADIER BRUSH - S-SERIESComplete HE-SR467 159.90(A) Hex head screw P-2077 .60(B) Flat washer P-581 .60(C) Nut P-2603 .60(D) Thumb screw P-2924 24.90(E) Bracket only HE-SR485 54.90(F) Spring washer P-654 .80(G) Sheet steadier brush HE-SR475 69.90

FEEDER BRUSH WHEEL - S-Series, Spdmst. 72/102Complete HE-SR403 89.90(A) Spring P-12319 1.40(B) Thumb screw P-2903 8.90(C) Small bracket HE-SR498 22.00(D) Hex head screw P-2043 .60(E) Large bracket HE-SR473 38.90(F)Thumb screw P-2924 24.90(G) Holder HE-SR492 44.90(H) Pin P-4777 7.00(I) Brush wheel HE-SR420 21.20(J) E-Ring P-2753 .60

SHEET SMOOTHERS

KOR (Complete) HE-KØR434 134.90KORD/KORA (Complete) HE-KØRD434 118.90KORS (Complete) HE-KØRS434 123.90(A) Spring plate (smoother) HE-KØ779 3.00(B) Screw P-2355 .80(C) Bar only (KOR) ** HE-KØR483 61.90(C) Bar only (KORD/KORA) ** HE-KØRD483 61.90(C) Bar only (KORS) ** HE-KØRS483 79.80(D) Block HE-KØR359 33.80(E) Thumb screw P-2924 24.90

SHEET SMOOTHER - GTO 46 (Long)

Complete HE-46434 109.80(A) Bar only HE-46483 59.90(B) Thumb screw P-2924 24.90(C) Block only HE-KØR359 33.80(D) Screw P-2305 .60(E) Nut P-2600 .60(F) Pan head screw P-2355 .80(G) Plate spring HE-46779 2.50(H) Roll pin P-516 .60

A CB

A

BC

D

AB

CE

DFG

J I H

GF

ED

BA

D

E

CB

A

C

B F

G

D&E

HA

SHEET SMOOTHER - GTO 46 (Short)Complete HE-46352 89.80(A)Bar only (Not Sold Alone) --------(B)Thumb screw P-2924 24.90(C)Block only HE-KØR359 33.80(D)Roll pin P-516 .60

Note: ** bars come without holes - you must drill holes to match your existing block.

SHEET SMOOTHER - GTO 52Complete HE-52434 119.90(A) Bar only HE-52483 59.90(B) Thumb screw P-2924 24.90(C) Block only HE-KØR359 33.80(D) Pan head screw P-2355 .80(E) Plate spring HE-46779 2.50(F) Roll pin P-516 .60

Note: ** bars come without holes - you must drill holes to match your existing block.

SHEET SMOOTHER PLATE SPRINGS

SORZ, SORDZ, SORSZ HE-SØ588 19.90

SORKZ, SORMZ HE-SØ924 10.90

SHEET SMOOTHER - S-SeriesComplete (Operators side) HE-SØ562 160.00Complete (Drive side) HE-SØ568 160.00(A) Spring plate HE-SØ779 3.20(B) Screw P-10207 .60(C) Bar only ** HE-SØ483 64.90(D) Block HE-SØ359 38.90(E) Thumb screw P-2923 9.90(F) Spacer piece (oper. side) HE-SØ541 42.90(F) Spacer piece (drive side) HE-SØ573 42.90

SHEET BRAKE - GTO 46 / 52, K-SeriesComplete HE-52467 70.00(A) Strap only HE-52500 9.90(B) Block only HE-52473 29.90(C) Thumb screw P-2924 24.90(D) Stop nut P-2610 .60(E) Screw P-8174 10.40

D

ACB

C

B D

F

AE

E

D C

F

AB

AE

B

DC

PART # PART #


Replacement parts for: HEIDELBERG ....................................Continued thru page 31.

TRANSFER GRIPPER - MOZ, SPEEDMASTER, SORKHE-MT225 38.90

GTO 46 / 52(A) Transfer and Imp. drum (urethane tip) HE-52245 49.90(A) Transfer and Imp. drum (plain metal tip) HE-52237 33.00(B) Imp.—Perfecting drum (urethane tip) HE-MØ237 135.90

Reversing Drum (upper position) HE-521020-RU 79.90Reversing Drum (lower position) HE-521020-RL 59.90

K-SERIES(C) Transfer and Imp. drum (metalized grit tip)HE-KØR225 39.50

M-SERIES(D) Feed drum (urethane tip) HE-72225 38.90(A) Transfer and Imp. drum (urethane tip) HE-52245 49.90(A) Transfer and Imp. drum (plain metal tip) HE-52237 33.00(A) Transfer drum—Coating unit (metal tip) HE-52237 33.00(A) Imp. drum—Coating unit (urethane tip) HE-52245 49.90(A) Imp. drum—Coating unit (plain metal tip) HE-52237 33.00

HE-MO1020 19.90HE-MO1050 6.90

QUICKMASTER 46 / 46DI & TOM / TOK(E) Impression drum (urethane tip) HE-46237QM 30.50

S-SERIES(F) Transfer and Imp. drum (urethane tip) HE-SK237 65.00(F) Transfer and imp. drum (plain metal tip) HE-SK245 39.00(J) Imp. cylinder gripper-SBD (urethane tip) HE-SBD237 189.90

HE-SK1000 87.90

SPEEDMASTER 72 (F) Transfer and Imp. drum (urethane tip) HE-SK237 65.00(F) Transfer and Imp. drum (plain metal tip) HE-SK245 39.00(G) Imp.—Perfecting drum (plain metal tip) HE-72245S 110.90(G) Transfer drum (large)

—Perfecting (plain metal tip) HE-72245S 110.90

SPEEDMASTER 102(H) Feed drum (urethane tip) HE-102237 29.20(H) Feed drum (plain metal tip) HE-102245 36.90(H) Transfer and Imp. drum (urethane tip) HE-102237 29.20(H) Transfer and Imp. drum (plain metal tip) HE-102245 36.90( I ) Imp.—Perfecting drum (plain meta l tip) HE-102225 53.90

GROOVED GRIPPER PADS - Speedmaster 72

Cross groove HE-72422-CG 59.90Parallel groove HE-72422-PG 46.90

GROOVED GRIPPER PADS - Speedmaster 102

Cross groove HE-102422-CG 24.90Parallel groove HE-102422-PG 59.90Diamond groove HE-102422-DG 22.00

Forwarding Sucker Assembly

Operator Side HE-S0990-0S 769.90

Non-Operator Side HE-S0990-DS 769.90

GROOVED GRIPPER PADS (Cross groove)Speedmaster 72 / 102 (after perfector)Drive side HE-72442-D 336.00Center HE-72442-C 155.00Operators side HE-72442-Ø 420.00

A B C D E

F G H I J

INK DISTRIBUTOR ADJUSTING BLOCKS - K-SeriesDrive side (complete) HE-KØR494K-DS 264.00(consists of (A) thru (J) & (K) HE-KØR494-DS. 120.00Operators side (complete) HE-KØR494K-ØS 264.00(consists of (A) thru (J) & (K) HE-KØR494-ØS. 120.00BEARING LATCH ASSEMBLY (items (A) thru (F).(A) Screw-Cone point P-2132 3.90(B) Spring HE-46896 .80(C) Latch HE-KØR494-L 28.50(D) Stud P-7164 9.80(E) Spring washer P-11826 2.90(F) Taper pin P-431 .60

JOURNAL BOX ASSEMBLY (items (G) thru (J).(G) Journal box HE-KØR494-JB 38.00(H) Retaining ring P-2771 .60(I) Needle bearing P-2117 15.90(J) Adjusting screw P-2913 8.20(K) Block (drive side) HE-KØR494-DS 120.00(K) Block (oper. side) HE-KØR494-ØS 120.00

JOURNAL BOX HOUSING ASSY. (items B, G, H, I, &J)HE-KØR494-JBC 104.00

SPINDLE For blanket cylinder

TOM, TOK P-27744 44.90

SHEET STOP For side laysM-Series, S-series, Speedmaster

HE-102100 38.90

CLAW For blanket clamp HE-46390 8.90

THREADED BUSHING For plate cylinderGTO 46 & 52 HE-46329 30.00

TRIP BLOCK For plate camGTO 52 HE-52391 3.20

ADJUSTING SCREW - For WINDMILL LAY BAR

10 X 15, 13 X 18(32 mm O.A.L.) HE-WI135-32 77.90(39 mm O.A.L.) HE-WI135-39 67.90

CYLINDER BRUSHES

KOR, KORA, KORD-62 P-7659 401.00KORD-64 P-7657 499.90KORS P-7658 349.90

BLANKET BAR ASSEMBLY - M-Series

Complete HE-MØ252 479.90(A) Upper clamp HE-MØ258 312.00(B) Lower clamp HE-MØ256 312.00(C) Screw (7 per assembly) P-2009 .60(D) Spring (6 per assembly) (not shown) P-12319 1.40

HOLDER ASSEMBLY - GTO 46 / 52, K-Series

Complete HE-KØ625 49.90Replacement roll pin P-2839 .60Replacement thumb screw P-2022 3.90

A

B

C


PART # PART #

24


BLANKET BAR ASSEMBLIES

Complete (GTO 46) HE-46252 380.00Complete (GTO 52) HE-52252 323.80Complete (SM 52) HE-52252SM 579.90Complete (KOR) HE-KØR252 799.90Complete (KORD) HE-KØRD252 810.00Complete (KORS) HE-KØRS252 899.90Complete (SM 72) HE-72252 400.00Complete (SM 74) HE-74252 639.90Complete (SM 102) HE-102252 465.00Complete (SORDZ) HE-SØRDZ252 909.80Complete (SORKZ) HE-SØRKZ252 650.00Complete (SORZ) HE-SØRZ252 670.00

PLATE CLAMP ASSEMBLY - TAIL EDGE

GTO 46 Complete HE-46367 591.90GTO 52 Complete HE-52367 639.80

(A) Upper clamp - GTO 46 HE-46359 124.90(A) Upper clamp - GTO 52 (left hand) HE-52359-L 69.90(A) Upper clamp - GTO 52 (right hand) HE-52359-R 69.90(B) Knurled adjusting nut P-2949 26.90(C) Eccentric shaft - GTO 46 HE-46435 58.90(C) Eccentric shaft - GTO 52 HE-52435 64.50(D) Adjusting stud P-7198 21.90(E) Lower clamp - GTO 46 HE-46353 240.00(E) Lower clamp - GTO 52 HE-52353 240.00(F) Threaded stud P-9138 13.00(G) Spring P-12909 2.50(H) Screw P-2418 .90(I) Metal strip - GTO 46 HE-46353-M 40.00(I) Metal strip - GTO 52 HE-52353-M 45.00(J) Set screw (not shown) P-2508 .60(K) Rubber strip - GTO 46 HE-46353-R 15.80(K) Rubber strip - GTO 52 HE-52353-R 15.80

(I,K) Metal & rubber strip assy. - GTO 46 HE-46353-MSR 79.60(I,K) Metal & rubber strip assy. - GTO 52 HE-52353-MSR 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGE

GTO 46 Complete HE-46788 499.90(A) Upper clamp HE-46359 124.90(B) Eccentric shaft HE-46435 58.90(C) Thumb screw P-2917 13.90(D) Spring HE-46896 .80(E) Screw P-2101 .60(F) Washer P-5519 .60(G) Adjusting bracket HE-46755 32.90(H) Lower clamp HE-46353 240.00(I) Spring P-12909 2.50(J) Screw P-2418 .90(K) Metal strip HE-46353-M 40.00(L) Set screw (not shown) P-2508 .60(M) Rubber strip - GTO 46 (not shown) HE-46353-R 15.80(K,M) Metal & rubber strip assy. - GTO 46 HE-46353-MSR 79.60

PLATE CLAMP ASSEMBLY - TAIL EDGE - For BACHER PLATEGTO 46 Complete HE-46367-BC 639.80(A) Upper clamp - (L.H.) HE-46359-L 69.90(B) Upper clamp - (R.H.) HE-46359-R 69.90(C) Knurled adjusting nut P-2949 26.90(D) Flat washer P-10942 1.20(E) Eccentric shaft HE-46435 58.90(F) Adjusting stud P-7198 21.90(G) Lower clamp sub assembly HE-46353-BC-S 240.00(H) Lower clamp only HE-46353-BC 180.00(I) Rubber strip HE-46353-R 15.80(J) Metal strip HE-46353-M 40.00(K) Threaded stud P-9138 13.00(L) Spring P-12909 2.50(M) Screw P-2418 .90(I,J) Metal & rubber strip assembly HE-46353-MSR 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGE - For BACHER PLATEGTO 46 Complete HE-46788-BC 839.80(A) Collar P-6725 55.80(B) Collar scale P-6726 63.00(C) Adjustment holder HE-52351 29.80(D) Washer P-2749 1.00(E) Spacer P-6802 7.90(F) Spring P-12148 3.80(G) Threaded stud P-9137 14.90(H) Spring P-12909 2.50(I) Adjusting block HE-52755 29.90(J) Ring scale P-6724 55.80(K) Adjusting stud P-7199 7.90(L) Lower clamp HE-46353-BC 180.00(M) Metal strip (not shown) HE-46353-M 40.00(N) Eccentric shaft (2 per assm) HE-46435 58.90(O) Upper clamp (1 per assm) HE-46359 124.90(P) Rubber strip (not shown) HE-46353-R 15.80(M,P) Metal & rubber strip assembly HE-46353-MSR 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGEGTO 52 Complete HE-52788 699.90(A) Clamp HE-52359 134.90(B) Knurled adjusting nut P-2949 26.90(C) Spacer P-6843 5.80(D) Spring P-12148 3.80(E) Eccentric shaft HE-52435 64.50(F) Spring P-12909 2.50(G) Adjusting stud P-7198 21.90(H) Lower clamp HE-52353 240.00(I) Screw P-2418 .90(J) Set screw P-2508 .60(K) Metal strip HE-52353-M 45.00(L) Rubber strip (not shown) HE-52353-R 15.80(K,L) Metal & rubber strip assembly HE-52353-MSR 79.60

PART # PART #



PLATE CLAMP ASSEMBLY - LEAD EDGE - For BACHER PLATE

GTO 52 Complete HE-52788-BC 639.90(A) Collar P-6725 55.80(B) Collar scale P-6726 63.00(C) Adjustment holder HE-52351 29.80(D) Spacer cam P-6843 5.80(E) Spring P-12148 3.80(F) Threaded stud P-9137 14.90(G) Adjusting stud P-7199 7.90(H) Adjusting block HE-52755 29.90(I) Lower clamp HE-52353 240.00(J) Metal strip HE-52353-M 45.00(K) Spring P-12909 2.50(L) Hex head screw P-2089 20.40(M) Ring scale P-6724 55.80(N) Nut P-2634 6.50(O) Eccentric shaft HE-52435 64.50(P) Clamp HE-52359 134.90(Q) Rubber strip HE-52353-R 15.80(J,Q) Metal & rubber strip assembly HE-52353-MSR 79.60

PLATE CLAMP ASSEMBLY - KORD 64

Complete HE-KØRD367 1,049.80(A) Screw (4 per assm) P-2008 .60(B) Upper clamp HE-KØRD359 300.00(C) Flat washer P-10942 1.20(D) Spring (4 per assm) P-12319 1.40(E) Lower clamp HE-KØRD353 569.90(F) Screw (2 per assm) P-2105 .70(G) Washer (2 per assm) (not shown) P-5519 .60(H) Block HE-KØR755 128.90(I) Nut (3 per assm) P-2604 .60(J) Set screw (3 per assm) P-2510 1.20

INK UNIT OVER-RUNNING CLUTCH ASSEMBLYCOMPLETE (K-Series) HE-KØ370 829.90COMPLETE (SM 72/102) HE-72370-CON

(A) Retaining ring P-2778 1.30(B) Flat washer P-2715 4.90(C) Ring washer P-2716 4.90(D) Bearing cage P-3452 43.00(E) One-way clutch bearing P-3447 279.90(F) Bearing cage P-3448 149.90(G) Housing Not Sold Alone - - - - -(H) Sleeve HE-KØ370-S 159.90

ADJUSTING GEAR For distributor roller.

KORD 64 HE-KØRD516 179.90

B D C I H F J A

E

GB

A

C

D E

F

H

• STANDARD CYLINDER JACKETSWINDMILL 10 X 15 .....10 x 14-1/4 ......................... P-30850 75.00WINDMILL 13 X 18....... 12-7/8 x 17-3/4 ................... P-30858 102.50GTO 46 ........................ 15-1/2 x 18 ......................... P-30851 50.00GTO 52 ........................ 16 x 20-3/8 ......................... P-30852 74.00M-Series....................... 21-1/2 x 26 ......................... P-30853 149.90KORD 62 ..................... 19-1/4 x 24-7/16 ................. P-30854 119.80KORD 64 ..................... 19-1/2 x 25-1/2 ................... P-30855 129.00KOR ............................. 16-3/4 x 22-1/2 ................... P-30859 199.90KORA .......................... 17 x 22-1/2 ......................... P-30857 110.90KORS .......................... 22-1/2 x 28-1/2 ................... P-30856 151.80Speedmaster 52 ........... 15-1/4 x 20-7/8 ................... P-30867 249.90

• REFINED CYLINDER JACKETSGTO 46 ........................ 15-1/2 x 18 ......................... P-30860 599.90GTO 52 ........................ 16 x 20-3/8 ......................... P-30861 998.00MO ............................... 21-3/4 x 26.......................... P-30862 1,699.00Speedmaster 72 .......... 21-1/16 x 29-1/4 ................. P-30863 1,455.00Speedmaster 74 ........... ........................................... P-30872 1,867.00Speedmaster 102 ........ 27-15/16 x 40-3/4................ P-30864 1,998.00

• DIE CUTTINGKSBAZ ........................ 21-1/2 x 28-1/2 ................... P-30865 290.00SBB, SBBS, SBBZ ....... 21-1/4 x 32-1/4 ................... P-30866 299.90KSBA .......................... 18-5/8 x 22-1/2 ................... P-30869 193.05S-Series ...................... 22-1/4 x 28-3/8 ................... P-30887 184.00SBG ............................. 24 x 30-1/4 ......................... P-30890 320.00

INK DISTRIBUTOR RUNNERWINDMILL 10x15 HE-WI466 17.70

DOG AND WORM - Quickmaster 46 / 46DI

Dog & Worm set HE-46464QM-K 153.90

Worm - Ink / Water HE-46464QM 128.90Dog - Water HE-46428QM 74.90

INK FOUNTAIN END PLATESSold as a set of 1 Left hand & 1 Right hand.Quickmaster 46 HE-46566QM 79.90Quickmaster 46DI HE-46566QMDI 110.00GTO 52 HE-52566 159.00GTO 52 CPC/CPT HE-52566CP 218.00GTO 46/52 Numbering Unit HE-46566-N 99.90Speedmaster 52 HE-52566SM 133.40Speedmaster 72 HE-72566 165.60Speedmaster 74 HE-74566 107.00Speedmaster 102 HE-102566 165.60MO HE-MØ566 120.00Spring plate for all (O.S.) HE-72261 7.00Spring plate for all (N.O.S.) HE-72082 7.00Hickey picker for all P-31108 .60


PART # PART #

26


HICKEY REMOVERS

(A) SORS, SORD, SORM, MOP-29981 79.90

(B) Speedmaster 52 P-29983 79.90

(C) Speedmaster 74 P-29982 79.90

(D) Speedmaster 102 P-29980 79.90

RUBBER REPLACEMENT (not shown)for P-29980 only. P-31336 4.00

ADJUSTING SCREW ASSEMBLYComplete HE-46427 66.00(A) Screw P-6530 44.90(B) Brass stud P-7174 31.50(C) Nut P-2601 .60(D) Lockwasher P-11830 .60

INK BLADE ADJUSTING SCREWS

(A) K-Series P-2929 22.90(B) GTO 46/52, M/S Series, Spdmstr 72

P-2928 26.90(C) TOK P-2021 5.20

INK ROLLER ASSEMBLY - Windmill 10x x15 (With bearings and runners.)Complete P-31999 148.90

WATER BACK UP / FEED COLLAR ASSY - K-Series

COMPLETE HE-KØ538 243.80(A) Collar - w / “B & D” HE-KØ355 237.80(B) Bearing P-3460 6.00(C) Spring P-362130 1.80(D) Roll pin P-10452 .60(E) Cam roller P-6838 38.90(F) Stud P-7169 21.00

BEARING SUPPORTS

GTO 46 D.S. - RED / O.S. - YELLOW, GTO 52 D.S. - RED -COMPLETE (w/o latch) HE-46558 340.00GTO 52 O.S. - YELLOW -COMPLETE (with latch) HE-52558 470.00GTO 46 & 52 D.S. - YELLOW / O.S. - RED -COMPLETE (w/o latch) HE-46614 339.90(A) Set screw Not Sold Alone ---------(B) Set screw P-2538 1.40(C) Shoulder screw P-8171 9.90(D) Handle P-7214 24.90(E) Spring (inside handle “D”) Not Sold Alone ---------(F) Trunnion stud P-7173 25.90(G) Set screw (to hold “H”) P-2501 .60(H) Eccentric stud P-7163 47.90(I) Dowel pin with o-ring P-4780 10.50(J) O-ring (comes with P-4780) P-5330 .60(K) Spring (underneath “B”) P-152422 3.90

A

B

CLOWER DAMPENING BEARING SUPPORT

GTO 46 & 52 D.S. GREEN - Complete HE-46415 574.00GTO 46 & 52 O.S. GREEN - Complete HE-46400 574.00(A) Spring (inside handle “B”) HE-46896 .80(B) Handle P-7214 24.90(C) Shoulder screw P-8171 9.90(D) Dowel pin P-3132 6.90(E) Trunnion stud P-7173 25.90(F) Set screw (to hold “G”) P-2501 .60(G) Eccentric stud P-7163 47.90(H) Grooved pin P-2899 4.50(I) Grooved pin with o-ring P-4780 10.50(J) O-ring (comes with P-4780) P-5330 .60(K) Brass stud P-7174 31.50(L) Nut P-2601 .60(M) Screw (for brass stud) P-6530 44.90

UPPER DAMPENING BEARING SUPPORT

GTO 46 & 52 D.S.Complete HE-46344 349.90GTO 46 & 52 O.S.Complete HE-46346 339.90(A) Support only HE-46350 149.90(B) Handle P-7214 24.90(C) Shoulder screw P-8171 9.90(D) Spring (inside handle “B”) HE-46896 .80(E) Trunnion stud P-7173 25.90(F) Set screw (to hold “G”) P-2501 .60(G) Eccentric stud P-7163 47.90(H) Dowel pin with o-ring P-4780 10.50(I) O-ring (comes with P-4780) P-5330 .60

INK FOUNTAIN BLADES

WINDMILL 10x15 .............. (37.6 cm x 10.1 cm) ....HE-WI095-15 299.90WINDMILL 13x18 .............. (48.0 cm x 10.1 cm) ....HE-WI095-18 447.90GTO 46 ............................. (45.3 cm x 8.4 cm) ......HE-46095 450.00GTO 46 (Numbering Unit) ... ...................................HE-46095-N 899.90GTO 52 ............................. (51.3 cm x 9.4 cm) ......HE-52095 399.90GTO 52 (Segmented) ......... ...................................HE-52095-S 1290.00GTO 52 (Numbering Unit) ... ...................................HE-52095-N 899.90KOR .................................. (58 cm x 10.1 cm) .......HE-KØR095 369.90KORD 64 .......................... (67.1 cm x 10.1 cm) ....HE-KØRD095 350.00KORS ................................ (74.2 cm x 10.1 cm) ....HE-KØRS095 328.50M Series ............................ (66.2 cm x 12.9 cm) ....HE-MØØ95 479.90SORDZ .............................. (90.1 cm x 11.7 cm) ....HE-SØRDZ095 600.00SORM ............................... (73.0 cm x 11.7 cm) ....HE-SØRM095 979.90SORMZ ............................. (73.1 cm x 17.5 cm) ....HE-SØRMZ095 750.00SORZ ................................ (83.1 cm x 11.8 cm) ....HE-SØRZ095 599.90SORKZ ............................. (66.0 cm x 11.8 cm) ....HE-SØRKZ095 593.00SORSZ ............................. (103.1 cm x 17.5 cm) ..HE-SØRSZ095 974.90TOK, TOM (27.6 cm x 7.1 cm) ......HE-T0095 280.00QUICKMASTER 46 ........... (33.6 cm x 7.1 cm) ......HE-46079QM 240.00

PART # PART #


Replacement parts for: HEIDELBERG.................................Continued thru page 31.

DAMPENING ROLLER ADJUSTMENT BLOCK

Complete HE-KØR416 140.00(A) Gear shaft HE-KØR304 73.90(B) Spring HE-KØR328 2.00(C) Bracket HE-KØR418 89.80(D) Knurled nut P-2946 9.50(E) E-ring P-2754 .60(F) Decal washer P-7464 4.90(G) Decal washer P-7465 4.90(H) Nut P-2603 .60

WATER TROUGH END SUPPORT

KOR HE-KØR10102 13.70

PLASTIC WATER FOUNTAIN ROLLER BEARING

KOR HE-KØR10104 2.20

WATER FOUNTAIN HOSE CLAMP

K-Series HE-KØR347 38.90

Spring for M-Series Delivery Gripper

Operator Side HE-M01081 6.70Non-Operator Side HE-M01080 2.40

WATER FOUNTAIN TRAYS

(A) TOM, TOK HE-TØ316 262.00(B) GTO 46 Old style (ser # 650058-654211) HE-46316-ØS 184.00(C) GTO 46 New style (ser # 656798-698328) HE-46316-NS 184.00

BUFFER SPRING - Windmill 10x15, 13x18

For roller carriageHE-WI444 32.90

WATER CLUTCH ASSEMBLY - GTO 46 & 52

HE-46418 90.00

OVER RUNNING CLUTCH LEVER ASSEMBLY - GTO 46 & 52

Complete - Ink unit HE-46259 599.90(A) Lever & knob assembly P-320416 32.00(B) Collar - without pins P-6785 64.80(C) Bearing race HE-46261 51.80(D) One way clutch bearing P-3454 389.90(E) Collar - with pins P-6784 64.80(F) Washer - bearing retainer P-2720 .60(G) Belleville washer P-11833 6.90

A B C

OVER RUNNING CLUTCH ASSEMBLY - GTO 46 & 52

Complete (INK) HE-52226 362.90Complete (WATER) HE-52370 440.00

(A) Sleeve HE-52226-S 82.90(B) One way clutch bearing P-3458 109.90(C) Housing only (Not Sold Alone) - - - - - (D) Pin P-4792 1.80(E) Washer P-2720 .60(F) Retaining ring P-10752 1.10

TEFLON SEALS SETS For Quickmaster 46 (set includes 1 ea. left / right hand)

(A) 95mm From end to end P-31161 48.80(B) 102 mm From end to end P-31181 49.80

TEFLON SEAL PACKS(A) Pack of 5 sets P-31161-5 236.00(A) Pack of 10 sets P-31161-10 462.00

(B) Pack of 5 sets P-31181-5 236.00(B) Pack of 10 sets P-31181-10 462.00

TEFLON SEALS - GTO 46 / 52 - For use on Varn units.1 Pack only (2 pcs.) P-30712 19.90Set of 5 packs P-31168 97.50Set of 10 packs P-31169 188.90

TEFLON SEALS - TOK / TOM - For use on Heidelberg dampening units1 Pack only (2 pcs.) P-30713 18.90Set of 5 packs P-30833 89.50Set of 10 packs P-30834 174.90

**1 pack consists of: (1) Right hand seal and (1) Left hand seal.

DAMPENING FELTS

QUICKMASTER P-11739 4.70QUICKMASTER DI P-11740 9.50

ANGLE - Paper stripper.GTO 46 & 52 HE-462301 229.90

HOLD DOWN STRAPS For HE-462301 shown at top left column, this page.

GTO 46 / 52 HE-462281 26.90

SPRING CLIP For HE-462281 shown above.

GTO 46 / 52 HE-462321 .90

GRIPPER FINGER - GTO 46/52, K-Seriesw/o Urethane HE-521050 1.50with Urethane HE-521020 9.90


PART # PART #

28


GRIPPER BAR ASSEMBLIES - GTO 46/52, K-Series

Complete (GTO 46) HE-460990 949.90Complete (GTO 52) HE-520990 999.90Complete (KOR, KORA, KORD 62) HE-KØR0990 1,200.00Complete (KORD 64) HE-KØRD0990 1,330.00Complete (KORS) HE-KØRS0990 1,750.00

(A) Anvil (GTO 46) HE-461090 459.90Anvil (GTO 52) HE-521090 483.90Anvil (KOR, KORA, KORD 62) HE-KØR1090 560.00Anvil (KORD 64) HE-KØRD1090 554.90Anvil (KORS) HE-KØRS1090 664.90

(B) Shaft (GTO 46) HE-461060 65.80Shaft (GTO 52) HE-521060 63.90Shaft (KOR, KORA, KORD 62) HE-KØR1060 108.90Shaft (KORD 64) HE-KØRD1060 109.80Shaft (KORS) HE-KØRS1060 109.80

(C) *Holder assembly HE-521000 47.00(D) **Holder HE-521061 26.90(E) **Finger with urethane HE-521020 9.90(F) **Backing plate HE-521062 3.00(G) **Holding screw P-2003 .60(H) **Belleville washer P-651 1.00(I) **Shoulder screw P-8161 5.50(J) *Arm assembly (GTO 46 & 52) HE-521040 189.90

*Arm assembly (KOR, KORA, KORD62) HE-KØR1040 120.00*Arm assembly (KORS, KORD 64) HE-KØRD1040 107.80

(K) **Arm only (GTO 46 & 52) HE-521041 119.00**Arm only (KOR, KORA, KORD62) HE-KØR1041 76.90**Arm only (KORS, KORD 64) HE-KØRD1041 76.90

(L) **Cam roller stud (GTO 46&52) P-7159 16.90**Cam roller stud (K series) P-7169 21.00

(M) **Cam roller (GTO 46 & 52) P-11179 38.90**Cam roller (K series) P-6840 32.90

(N) **Pin (GTO 46 & 52) P-373 .60**Pin (K series) P-1894 .60

(O) Collar P-6739 12.00(P) Spring (GTO 46 & 52) HE-521080 4.90(Q) Spring (GTO 52) HE-521085 4.50(R) Pin P-2834 .60(R) Screw (K series) P-2101 .60

*indicates a sub-assembly. **indicates components of a sub-assembly.Note: Item (B) Shaft must be taper reamed for pins in field.

GRIPPER PADS - SPEEDMASTER 72 & 102

(A) For ultraviolet & infrared dryersHE-721061-U 14.90

(B) For standard HE-721061 24.90

GRIPPER PAD RAIL For S-Series gripper bars.

HE-SK1061 19.90

WATER OSCILLATING HOUSING ASSEMBLY

K-SeriesOperators side HE-KØ429 349.80Drive side (shown) HE-KØ431 429.90

GEAR FOR METERING ROLL - QM46

(A) Overall Length: 13.5 mmHE-46555QM 10.00

(B) Overall Length: 22 mmHE-46555QM-UG 72.70

A

B

A

B

GRIPPER BAR ASSEMBLY - TOKComplete HE-T00990 699.90(A) Anvil HE-T01090 520.00(B) Set screw P-2506 .60(C) Collar P-6728 4.00(D) Shaft HE-T01060 49.90(E) Gripper finger HE-T01020 14.90(F) Cap screw P-2112 .60(G) Gripper pad P-11904 3.50(H) Gripper spring HE-T01085 3.50(I) Tension collar P-6734 19.90(J) Set screw P-2512 .60(K) Gripper spring HE-T01080 2.30(L) Taper pin P-2810 .60(M) Stop nut P-2610 .60(N) Gripper operating lever HE-T01041 32.50(O) Washer P-580 .60(P) Ball bearing P-11113 8.00(Q) Screw P-2103 .60(R) Bushing P-3239 3.00

GRIPPER BAR ASSEMBLY - QUICKMASTER 46 & 46DI

COMPLETE (46) HE-460990QM 519.90COMPLETE (46DI) HE-460990QMDI 549.90(A) Anvil (comes with P-11904 (Angled Pad) HE-461090QM 339.80(A) Anvil (comes with P-5631 (Flat Pad) HE-461090QMDI 369.90(B) Set screw P-2506 .60(C) Adjusting collar P-6858 38.90(D) Gripper spring HE-461080QM 9.90(E) Delivery gripper for 46 HE-461020QM 23.90(E) Delivery gripper for 46DI HE-461020QMDI 23.90(F) Screw P-2112 .60(G) Gripper shaft HE-461060QM 68.90(H) Taper pin P-2810 .60

GRIPPER LEVER ASSEMBLY HE-461040QM 49.90(Consists of I thru M - also included with complete assembly)

• (I) Screw P-2103 .60• (J) Washer P-5569 .60• (K) Ball bearing P-11113 8.00• (L) Gripper lever only HE-461041QM 37.90

(M) Stop nut P-2610 .60(N) Rubber pad (Flat) P-11904 3.50(N) Rubber pad (Angled) P-5631 5.00

GRIPPER BAR ASSEMBLY - WINDMILL

Complete 10 X 15 HE-WI0990-15 540.00Complete 13 X 18 HE-WI0990-18 599.90

SCREW - For gripper bar operating arm HE-T1307 5.90

PART # PART #



GRIPPER BAR ASSEMBLYCOMPLETE (Speedmaster 72) ........................... HE-720990 3,999.00COMPLETE (Speedmaster 102) ......................... HE-1020990-U 3,999.00(A) Chain link - 4 ea. ......................................... P-8715 39.90(B-1) Carrier link assembly - operators side ........ HE-720991 320.00(B-1) Carrier link assembly - operators side ........ HE-1020991 289.70(B-2) Carrier link assembly - non-oper. side ........ HE-720992 320.00(B-2) Carrier link assembly - non-oper. side ........ HE-1020992 289.70

- Link only - for (B-1) ................................... HE-720991-L 196.00- Link only - for (B-1) ................................... HE-1020991-L 212.80- Link only - for (B-2) ................................... HE-720992-L 196.00- Link only - for (B-2) ................................... HE-1020992-L 212.80- Inner chain link - 2 for each assembly ....... P-8715 39.90- Needle bearing ......................................... P-3461 11.00- Dowel pin for P-8715 - 2 for each assy...... P-2898 2.80- Grease fitting ............................................ P-3672 1.30

(C) Washer ....................................................... P-2738 11.40(D) Screw.......................................................... P-2103 .60(E) Clamping piece ........................................... HE-721066 34.00(F) Finger ......................................................... HE-721020 139.90(G) Gripper supporting shaft.............................. HE-721060 329.90(G) Gripper supporting shaft.............................. HE-1021060 489.90(H) Center pivot bearing.................................... HE-721092 124.00( I ) Gripper operating lever ............................... HE-721040 189.90(J) Taper pin - 3 per complete assembly ........... P-2865 1.40(K) Cam roller ................................................... P-6871 66.20(L) Set screw .................................................... P-10017 .60(M) Spring guide................................................ P-2970 37.90(N) Pin .............................................................. P-4768 19.80(O) E-Ring......................................................... P-2759 .60(P) Clamp ......................................................... HE-721067 40.00(Q) Clamping piece ........................................... HE-721065 31.00

- Screw ....................................................... P-2103 .60- Nut............................................................ P-2603 .60- Lockwasher .............................................. P-10836 .60

(R) Screw.......................................................... P-2143 .60(S) Gripper pad ................................................. HE-721061-U 14.90(T) Clamp (also in S-Series) ............................. HE-721064 34.00(U) Shaft ........................................................... HE-721090 399.90(U) Shaft ........................................................... HE-1021090 450.00

CARRIER LINKS - K/M/GTO Series(A) M-Series - wide attachment P-8739 44.90(B) M-Series - short attachment P-8740 44.90(C) K-Series - operators side P-8732 44.90(C) K-Series - non-operators side P-8742 44.90(D) Star rod carrier link (K/S) P-8734 44.90(E) GTO 46/52 HE-521100-A

GRIPPER CHAIN CONNECTING LINKS(A) KOR, KORD, KORS / M-Series P-8761 9.50(B) KOR, KORD, KORS (offset link) P-8762 13.90(C) Connecting plate P-8712-P 8.50

AB1 C D E F G H I

B2

KL

MNO

PQRS

T

U

J

A B C

GRIPPER CHAINS

TOK (set) HE-T01100 115.00GTO 46 / 52 (set) HE-521100 219.00KOR (set) HE-KØR1100 2,200.00KORD (set) HE-KØRD1100 2,200.00KORS (set) HE-KØRS1100 1,199.00MO (set) HE-M01100 691.90SPEEDMASTER 72/102 HE-721100 207.00SORD HE-SØRD1100 219.90QUICKMASTER 46 (set) HE-461100QM 249.90QUICKMASTER 46DI (set) HE-461100DI

GRIPPER BAR ASSEMBLY CARRIER LINKSSPEEDMASTER 72 & 102

Complete (oper. side) HE-720991 320.00Complete (non-oper. side) HE-720992 320.00

(A) Link only (oper. side) HE-720991-L 196.00(A) Link only (non-oper. side) HE-720992-L 196.00(B) Inner chain link P-8715 39.90(C) Needle bearing P-3461 11.00(D) Dowel pin P-2898 2.80(E) Grease fitting P-3672 1.30

SHEET STOPS

1) KORD 62 ........................................................ HE-KØRD2281-62 34.00(for ser. #335790 & below, otherwise use HE-KØRD2282-64.)

2) KORD 62 & 64 ................................................ HE-KØRD2282-62 34.00(for ser. #335791 & above, otherwise use HE-KØRD2282-62.)

3) KORD 64 ........................................................ HE-KØRD2281-64 34.90

4) KORD 64 ........................................................ HE-KØRD2282-64 34.00for ser. #335791 and above, otherwise use HE-KØRD2282-62.)

5) KORA, KORD-64, KORS (front - side)............. HE-KØRD2284 49.90

6) KORA, KORD-62 (front - center) ..................... HE-KØRD2283-62 42.00

7) KORD-64, KORS (front - center) ..................... HE-KØRD2283-64 49.90

STRIPPER FINGER ............................................ HE-KS15112 2.90

STAR ROD BRUSH ASSY.

Complete P-30842 12.90Brush only P-30842-B 8.50Collar only P-30842-C 4.50Rubber O-ring P-553 .60

STAR ROD ASSEMBLIES

GTO 52 HE-523170 21.90KOR, KORA, KORD 62 HE-KØRD3170-62 77.90KORD 64 HE-KØRD3170-64 94.00M (series) HE-MØ3170 64.90SORDZ HE-SD3170 82.90SORZ HE-SR3170 87.90SORKZ HE-SK3170 87.90SORMZ / SPEEDMASTER 72 HE-SM3170 87.90SORSZ / SPEEDMASTER 102 HE-SS3170 92.50

NOTE: THESE DO NOT COME WITH BRUSHES OR WHEELS

D

EA

B

C

1 2 3

6 7

Stripper Finger

4 5


PART # PART #

30


POWDER TUBE ASSEMBLY

Complete (short tube)......................................... HE-KØR6030 524.90Complete (long tube) .......................................... HE-KØR6040 524.90

Powder tube sub assy. (A - I) ............................ HE-KØR6046 419.80(A) Manifold ...................................................... HE-KØR6050 119.90(B) Screw.......................................................... P-2044 .50(C) Washer ...................................................... P-592 .60(D) Gasket ........................................................ P-6422 1.00(E) Rubber washer............................................ P-11036 5.00(F) Lock nut ...................................................... P-2616 1.10(G) Powder tube guide ...................................... HE-KØR6051 49.90(H) Stop screw .................................................. P-2351 .60(I) Screw.......................................................... P-2082 .60

Spray nozzle sub assy. (J - M) .......................... HE-KØR6047 147.80(J) Nozzle......................................................... HE-KØR6056 42.00(K) Screw.......................................................... P-2921 6.90(L) Spring ......................................................... P-15601 3.90(M) Nozzle tube................................................. HE-KØR6055 119.90

Powder tube sub assy. - short (N - R) ............... HE-KØR6035 99.90

Powder tube sub assy. - long (N - R) ................ HE-KØR6045 120.00(N) Short tube (for HE-KØR6030) ..................... HE-KØR6052 65.80(N) Long tube (for HE-KØR6040) ..................... HE-KØR6053 68.00(O) Nut .............................................................. P-2681 .60(P) Compression nut with gasket ...................... P-2941 27.90(Q) Guide collar................................................. HE-KØR6054 65.80(R) Set screw .................................................... P-2499 .60

GUIDE WHEEL KIT - GTO 52

Complete HE-521327 25.80 Wheel only HE-521328 15.00 O-Ring P-11778 2.10 Set screw P-2580 .60

8 Watt FLOURESCENT BULB - GTO 46 / 52, TOM / TOK P-9743 9.00

14 Watt FLOURESCENT BULB - KORD 64 P-9726 22.00

BRASS FILTER SCREENS

Windmill Platens (24mm collar) P-9410 25.90GTO 46 & 52 (28 mm collar) P-9411 25.90GTO 46/52, Windmill (38 mm collar) P-9412 29.90

SLIP RING BRUSHES

K-Series (shown) P-9428 10.90S-Series P-9438 10.70S-Series P-9439 5.60Paired Collector Brush P-9429 61.90

PUMP VANE P-9444 59.90

CARBON BRUSHES

Carbon Brush P-9431 69.80Carbon Brush P-9432 4.00S-Series P-9769 38.90Speedmaster P-9433 69.90Speedmaster 102Z P-9434 69.90Speedmaster 102 P-9435 39.90Speedmaster 102V P-9436 29.90102D+L 102V (Main motor) P-9437 24.90TOK/TOM (Motor) P-9440 20.00

ROLLER SNAP SWITCH - All S-SeriesLocated on operators side outer delivery frame

P-9805 42.90

LIMIT SWITCHES

(A) GTO 46/52, M/S Series, Speedmaster 72/102 P-9836 124.90

(B) GTO 46/52, M/S Series, Speedmaster 72/102 P-9837 99.80

(C) GTO 52, M-Series, Spdmst 102 (snap action) P-9838 119.90(C) M-Series (slow action) P-9839 69.75

(D) GTO 46 / 52 - Located behind blower tubes P-4074 49.90

VARIABLE SPEED PULLEY For K-Series

P-4291 1,598.00

COMPRESSION SPRING - WINDMILL 10 x 15For variable speed control.

HE-WI046 85.70

BOWDEN CABLE

WINDMILL HE-WI3101 119.90

DELIVERY TABLE CABLE

K-Series HE-KØ971 55.00SB-Series HE-S1539 43.90

Lay Gauge Pin Kit

Set of 5 P-31133

Starwheel

(A) Star/Pointed Surface P-30842-0(for K/S/M series)

(B) Knurled/Dimpled Surface P-30842-GT0(GT0 46/52)

(B) Knurled/Dimpled Surface P-30842-K(for K/S/M series)

(C) Smooth/Plain Surface P-30842-S(for K/S/M series)

A B C D

A

B

C

PART # PART #


Replacement parts for: HEIDELBERG.................................Continued from page 21.

PNEUMATIC SPRING For Speedmaster 102

Safety guard (11-7/8” end to end) P-29990 101.20Delivery (16-5/8” end to end) P-29991 136.30

BLOW DOWN FAN For Speedmaster 102 delivery

Terminal connection P-4204 225.90Wire connection P-4205 225.90

EMERGENCY KITS

TOK/TOM P-31143 239.80Consists of: 6 Impression gripper fingers /1 Wash-up blade / 12 Sucker feet / 1 Set of teflon seals.

QUICKMASTER 46 P-31144 289.80 Consists of: 8 Impression gripper fingers / 1 Wash-up blade / 12 Sucker feet / 1 Dampening felt / 1 Tape track

QUICKMASTER DI46 P-31145 279.80Consists of: 8 Impression gripper fingers / 1 Wash-up blade / 12 Sucker feet / 1 Dampening felt

HARDWARE EMERGENCY KITS

HAS YOUR PRESS EVER BEEN DOWN DUE TO A SIMPLE PIN OR SPRING? YOU CAN ELIMINATE COSTLY DOWN TIME IN MINUTES WITH YOUR OWN EMERGENCY KIT DESIGNED TO CONVENIENTLY FIT IN YOUR DESK DRAWER. EACH KIT COMES IN IT’S OWN MULTI-COMPARTMENT RECLOSABLE BOX FOR QUICK, EASY SELECTION AND STORAGE. PART NUMBERS FOR THE INDIVIDUAL ITEMS ARE ALSO INCLUDED INSIDE.

MASTER KIT All kits below P-30397 219.90NUT KIT 43 pcs. P-30392 21.50WASHER KIT 60 pcs. P-30396 40.00SCREW KIT 168 pcs. P-30393 96.00RING KIT 47 pcs. P-30395 28.90PIN KIT 100 pcs. P-30394 37.50

CAM FOLLOWERS

GTO 46 (A) Transfer & imp. cylinder / gripper shaft. ....... P-3441 109.90(B) Side lay shaft. ............................................. P-4368 39.00

GTO 52(A) Transfer & impression cylinder & storage drum

/ gripper shaft.............................................. P-3441 109.90

K-SERIES(C) Imp. cyl.shaft

/ sucker bar mechanism Outer lever. ........... P-6870 109.90

M-SERIES(D) Transfer & impression cylinder & storage drum

/ gripper shaft.............................................. P-3416 197.90(E) Reversing drum........................................... P-3443 163.00(F) Register feed drum / gripper shaft. .............. P-3444 110.00

SORZ / SORDZ / SORKZ / SORMZ / SORSZ(G) Register feed drum / gripper shaft

..(cam facing cylinder O.S. & D.S.) .............. P-3442 119.00(H) Register feed drum / gripper shaft

..(cam facing side frames O.S & D.S.) ......... P-3445 155.00(F) Imp. cyl. & storage drum / gripper shaft. ...... P-3444 110.00

SPEEDMASTER 72 / 102(G) Register feed drum/ gripper shaft

..(cam facing cylinder O.S. & D.S.) .............. P-3442 119.00(H) Register feed drum / gripper shaft

..(cam facing side frames O.S. & D.S.) ........ P-3445 155.00(F) Transfer & imp. cylinder / gripper shaft. ....... P-3444 110.00(H) Transfer gripper........................................... P-3445 155.00

SPEEDMASTER 74(I) Delivery table. ............................................. P-3439 69.90

SPEEDMASTER 102(J) Gripper opening lever on del. gripper bars. . P-6871 66.20(G) On lever (OEM #71-010-110) / inking unit. .. P-3442 119.00

QUICKMASTER(A) Impression cylinder / gripper shaft. ............. P-3441 109.90

GTO 46INK ROLLER KIT P-30457 741.85Consists of:(6) Blue Distributor / Ductor P-46H10B 86.25(1) Red Form P-46H10R 89.65(1) White Form P-46H10W 86.25(1) Yellow Form P-46H10Y 87.50

KORD 62INK ROLLER KIT P-31656 1,597.05Consists of:(2) Blue Form / Distributor P-30916 203.90(3) Red Form / Distributor / Ductor P-30918 181.90(2) White Form / Distributor / Ductor P-30917 181.90(2) Brown Form / Distributor / Ductor P-30919 181.90

QUICKAMSTER 46 (1ST. UNIT)INK ROLLER KIT P-31735 755.25Consists of:(1) Yellow 1st. Ink Form P-34H10 128.00(1) Blue 2nd. Ink Form P-34H11 106.00(1) Black 3rd. Ink Form P-34H13 222.00(1) Black Ink Transfer Roll #1 P-34H20 86.00(1) Black Ink Transfer Roll #2 P-34H21 86.00(1) Black Ink Transfer Roll #3 P-34H22 81.00(1) Black Ductor P-34H30 86.00

A B C D E F G

H I J


PART # PART #

32

Replacement parts for: CHIEF 15, 115, 215, 17, 117, 217, 20, 22, 25/25 PROF,

VARIABLE SPEED PULLEY15, 17 P-1629 179.90

(Gestetner) G-63E115, 215, 117, 217 P-1627 169.90

(Gestetner) G-17E

V-BELTS15, 17 (Motor to pump)37” P-4906 9.90

(Gestetner) G-6C15, 17 (Clutch to motor)44” P-4912 12.5015 (Clutch to drive shaft)36” P-4905 9.9017 (Clutch to drive shaft)38” P-4907 9.00

(Gestetner) G-27E

RUBBER SUCTION FOOT - X-series & Super Chief 2000P-5225 120.00

SUCKER FOOT (CUP) P-5204 2.00

SUCKER FOOT P-5201 8.00(Gestetner) G-229G

FLAT SUCKER FOOT P-1552 .80

SUCKER TUBE HOLDER ASSEMBLYNew style 15, 17 P-15259 44.00

(Gestetner) G-16G(A) Holder P-15166 29.90(B) Retainer clip P-15227 8.00(C) Screw P-137 .60(D) Set screw P-864 .60

SHEET SEPARATOR(A) 15, 17 P-15114 .90(B) X-Series & Super Chief P-52114 .90

SHEET SEPARATOR ASSEMBLYComplete P-50112 64.00(A) Screw P-293 .60(B) Washer P-573 .60(C) Sheet separator P-52114 .90(D) Block P-50113 36.90(E) Plate P-50121 16.00(F) Screw (not shown) P-215 .60(G) Thumb screw P-1019 1.80

TIMING BELTS For feeder on X-Series & Super Chief 2000. Also for Davidson 500, 7003/4” wide X 22-1/2” long P-1662 22.903/8” wide X 15” long P-4965 12.00

ELEVATOR HANDLE ASSEMBLY Table raise X-Series & Super Chief 2000

P-50955 160.00

KNOB STUD For chain delivery & feed table handwheelP-4521 16.80

FEEDER GUIDEOperators side & non-operators side

P-15048 21.50

D

C B A

E

G DCA&B

LIFTING GEAR STUD For feeder ratchet15, 115, 215, 117, 217 4” wide w/wide shoulder P-4519 35.50 4” wide w/thin shoulder P-4542 28.00

BLOWER TUBE BRACKET P-15168 72.00(Gestetner) G-119G,G-128G

••• Designed to fit both left and right hand sides.

UPPER PULLOUT FEED ROLLERP-15125 34.90(Gestetner) G-17H

DOUBLE SHEET EJECTION ROLLERP-15273 10.90(Gestetner) G-19H

PAPER RETAINERCenter P-15433 26.90

(Gestetner) G-11S

CONVEYOR TAPE All modelsCloth P-3900 44.00Note: Tension can be adjusted by weights under conveyor.

JOGGER SIDE GUIDE FEATHER SPRINGNon-operators side R.H. P-15477 4.30

(Gestetner) G-16TOperators side L.H. P-15471 4.30

(Gestetner) G-11T

COUNTER (no lever)15 P-36954 58.00

(Gestetner) G-20K17 P-27954 129.00

COUNTER ARM P-15956 22.40(Gestetner) G-19K

PAPER STOPBy impression cylinder P-15383 89.90

ADJUSTING ARM For paper stopP-15853 53.00

PAPER STOP ARM ASSEMBLYP-15399 134.90

FEELER FINGER P-15141 4.80(Gestetner) G-55R(Gestetner) G-OW142

PART # PART #


126, Super Chief 2000, X-Series • GESTETNER 115/117G, 211, 213, 311, 312, 313

PAPER DEFLECTOR 15,17,115,117,215,217 P-15241 39.90(Gestetner) G-52R

PAPER DEFLECTOR X-Series, Super Chief P-255241 49.90SCREW P-44 .60

GRIPPER LEVER ASSEMBLYP-15207 119.80

(Gestetner) G-3M & G-E14AØ59

GRIPPER FINGER SUPPORT ASSEMBLYP-15187 6.90

CLAMP LOCK For plate cylinderP-115807 10.80

RETAINING BAR (20 point) Master cylinder15N.S. & 17 O.S./N.S. P-15746 87.90

TENSION GUIDE ARM SCREWFor plate cylinder P-11468 13.50

TAIL CLAMP ASSEMBLY - X-Series & Super Chief 2000 Complete P-255367 380.00 (A) Clamp bracket P-255729 46.00 (B) Spring P-255724 1.50 (C) Retaining ring (not shown) P-669 .60 (D) Shaft (not shown) P-255793 34.90 (E) Pin bar clamp P-255341 179.90 (F) Screw P-836 .60 (G) Pin bar (8 point) P-255323 49.90 (H) Pin bar (10 point) P-255739 49.90 (I) Thumb nut P-11549 9.90 (J) Thumb screw P-11498 13.50

DRIVE & PUMP TOGGLE SWITCH15, 17 O.S. & N.S. P-15305 31.80

DRIVE & PUMP ROCKER SWITCHP-15826 55.90

RELAY P-4833 79.90

G

I

J A B E

FH

PLATE CYLINDER GEAR15, 17, (14-1/2° PA) P-15313 220.00

(Gestetner) G-3P115, 117, 215, 217 (20° PA) P-115313 289.90

BLANKET CYLINDER GEAR15, 17 (14-1/2° PA) P-15214 214.90

(Gestetner) G-3N115, 117, 215, 217 (20° PA) P-115214 199.80

115, 117, 215, 217 (20° PA) P-115191 199.80

SPRING ASSEMBLY Impression cylinder arm15, 17 X-Series & Super Chief 2000Complete P-15205 24.00Clip P-6088 2.90Spring P-15213 7.50

DRIVE SHAFT15, 17 P-15583 74.90115, 117, 215, 217 P-115583 149.90

INTERMEDIATE DRIVE GEAR15,17 (14-1/2° PA) P-15865 72.90

(Gestetner) G-64RP-15457 69.90(Gestetner) G-E14H115,G-58L

115,117,215,217 (20° PA) P-115854 69.90

DRIVE GEAR For X-SeriesP-255854 139.90

CLUTCH PULLEY REPAIR KIT15, 17, 115, 117, 215, 217Complete P-15564 145.80Pulley cover P-15617 94.00

(Gestetner) G-35EShaft P-15614 24.90

(Gestetner) G-33EWeights (set of 4 only) P-12593 59.90

(Gestetner) G-37EV-Belt - 44” P-4912 12.50V-Belt - 37” P-4906 9.90

(Gestetner) G-6CSpring P-15591 4.30

(Gestetner) G-36EBearing (need 2) P-774 6.90

(Gestetner) G-3UKey P-550 .60

(Gestetner) G-ØWØ62

WATER CAM ASSEMBLYComplete P-15262 117.80

(Gestetner) G-170UACam P-15363 85.80

(Gestetner) G-9U, G-170UWater pawl P-15268 28.90

(Gestetner) G-163UPawl spring P-15267 3.90

(Gestetner) G-LØØ4058Ink pawl P-15355 28.90

(Gestetner) G-66V

WATER STOP15, 17, 115, 117, 215, 217

P-30379 35.90X-Series & Super Chief 2000 1st. & 2nd. head(Uses 16) P-5096 9.90


PART # PART #

34

Replacement parts for: CHIEF 15, 115, 215, 17, 117, 217, 20, 22, 25/25 PROF,

FRICTION BEARING For water fountain roller15, 17 P-5525 9.00

(Gestetner) G-157U

WATER DUCTOR ASSEMBLY - 15, 115, 215, 17, 117, 217Complete P-15424 184.90

(Gestetner) G-443(A) Shaft P-15540 34.90

(Gestetner) G-161U-S(B) Stud P-4500 21.50(C) Cam roller P-1450 6.50(D) Arm P-15607 24.90

(Gestetner) G-21U2(E) Yoke shaft P-15340 24.90

(Gestetner) G-2Ø42(F) Latch P-15551 4.30

(Gestetner) G-60U, G-91V(G) L.H. Spring P-15336 4.10

(Gestetner) G-62U, G-93V(H) Center pivot P-15322 29.90

(Gestetner) G-161UP( I ) Lever arm P-15344 67.00

(Gestetner) G-83VA(J) R.H. Spring P-15331 4.10

(Gestetner) G-61U, G-ØU56

WASH UP BLADE Black rubber 15 O.S. (11” X 11/16”) C-2167H-32 12.50 Tan 15, 17, (11-3/8” X 1-1/2”) C-2171D-524 16.00 215, 217 (11 X 2-1/8”) P-30309 25.95 XL, Super Chief 1st. head (13-3/4” X 1-1/8”) P-30238 25.95 XL, Super Chief 2nd. head (13-3/4” X 2-1/16”) P-30217 25.95

WATER FOUNTAIN SHAFT & RATCHET15, 17 P-15402 79.90115, 117, 215, 217 P-115402 97.90(A) Shaft 15, 17 P-15371 29.90(A) Shaft 115, 117 215, 217 P-115371 39.90(B) Ratchet P-15370 59.00(C) Pin P-381 .60

SHAFT For water form roller15, 17, 115, 117, 215, 217 P-15378 49.90

(Gestetner) G-15ØU

WATER DUCTOR LEVER SPRINGP-15549 5.50

CAM ROLLER Water oscillator armP-5831 40.00(Gestetner) G-129U

TIMING BELT17, 117 (water) P-1660 13.90

(Gestetner) G-5R2215, 217 (second water head)

P-1654 10.50

A

B

C

WORM GEAR ASSEMBLYInker unit P-15446 99.90

(Gestetner) G-192V

INK IDLER GEAR P-15455 69.90

OSCILLATING WORMInk & water P-15464 66.90

(Gestetner) G-134VDOGInk P-15463 48.90

(Gestetner) G-138V

••• DESIGNED WITH REPLACEABLE END CAPS.INK FOUNTAIN ASSEMBLY15, 115, 215 - (Gestetner) G-E31H477 P-15071 389.90Fountain only - (Gestetner) G-70V P-15072 174.00

INK FOUNTAIN ASSEMBLY With deeper ink well for 50% more ink capacity.17, 117, 217 P-17766 439.80Fountain only - (Gestetner) G-3V-3 P-17789 179.90

THUMB SCREW P-11474 13.50

INK FOUNTAIN BLADE15, 115, 215 P-15079 49.90

(Gestetner) G-73V17, 117, 217 Bigger blade for deeper ink well. P-17233 56.40

(Gestetner) G-11V2Note: * Due to the variations of ink fountains it may be necessary to file the side of the blade stamped “O” for a perfect fit.

INK DUCTOR ASSEMBLYComplete P-15690 208.00(A) Cam roller P-1431 6.50

(Gestetner) G-85V(B) Stud P-8096 9.40

(Gestetner) G-86V(C) Yoke shaft P-15550 21.80

(Gestetner) G-89V(D) Arm P-15572 24.90

(Gestetner) G-F14V012(E) Latch P-15551 4.30

(Gestetner) G-60U(F) R.H. Spring P-15331 4.10

(Gestetner) G-61U(G) L.H. Spring P-15336 4.10

(Gestetner) G-62U(H) Shaft P-15332 41.90( I ) Center pivot P-15322 29.90

(Gestetner) G-161UP(J) Lever arm P-15334 49.90

(Gestetner) G-83VA

IMPROVED

PART # PART #


126, Super Chief 2000, X-Series • GESTETNER 115/117G, 211, 213, 311, 312, 313

CONNECTING LINK BAR For chain delivery15, 17, 115, 117, 215, 217 P-151596 34.00

(Gestetner) G-120CP

ARM EXTENSION ASSEMBLY For chain pile delivery15, 17, 115, 117, 215, 217

P-151597 42.90

DELIVERY ROLL GRIPPERP-15644 4.90(Gestetner) G-OW138(Gestetner) G-33Q

BACK STOP STRIPPER For chain deliveryP-152280 6.00

GRIPPER SUPPORT P-15586 10.20

GRIPPER CHAINS (set of 2)15, 17, 115, 117, (Super Chief 2000 & X-Series 1st. head)

P-8945 72.00(Gestetner) G-548C3G-E1ØA323

215, 217, (X-Series & Super Chief 2nd. head) P-8949 120.0022 P-8969 83.00

CONNECTING LINK P-8700 5.00

PICK UP CAM ASSEMBLY To open gripper bars

P-151240 56.00(Gestetner) G-511C3

SPROCKET & SHAFT ASSEMBLY Chain delivery15, 17, 115, 117, 215, 217 P-151160 292.50

(Gestetner) G-113CPG-E1ØA157, G-E1ØA287

GRIPPER BAR ASSEMBLY••• Anvil is made of reinforced cast zinc which prevents bowing and lasts longer.

Complete P-150990 180.00(Gestetner) G-125CP

(A) Anvil P-151090 116.00(Gestetner) G-126CP

(B) Retaining ring P-670 .60 ** Gripper shaft assembly (C) - (E) P-151010 48.00 (C) Stop block P-151063 19.90 (D) Roll pin P-376 .60 (E) Shaft P-151060 32.00 (F) Cap screw P-40 .60 (G) Gripper holder P-151061 19.90 (H) Screw P-187 .60

(Gestetner) G-HS158 (I) Hold down clip P-151062 1.20

(Gestetner) G-HW307 (J) Gripper finger P-151020 1.70

(Gestetner) G-HW306 ** Gripper operating lever assembly (K) - (P) P-151040 49.00 (K) Gripper operating lever P-151041 32.00

(Gestetner) G-E10A173 (L) Cap screw P-39 .60

(Gestetner) G-CS42U (M) Hex nut P-479 .60

(Gestetner) G-L0HT051 (N) Lock washer P-627 .60 (O) Cam roller P-1424 7.80

(Gestetner) G-L0HW309 (P) Shoulder screw P-8037

(Gestetner) G-L0HS159 (Q) Collar (comes with set screw) P-98137 10.00 (R) Set screw P-2 .60 (S) Spring P-151080 1.80

(Gestetner) G-L0HU124

GRIPPER BAR REPAIR KIT - Super Chief 2000 & X-SeriesConsists of (B - D, F - P, Q, & S) P-30736 223.90

REPAIR KITS

HAS YOUR PRESS EVER BEEN DOWN DUE TO A SIMPLE PIN OR SPRING? YOU CAN ELIMINATE COSTLY DOWN TIME IN MINUTES WITH YOUR OWN EMERGENCY KIT DESIGNED TO CONVENIENTLY FIT IN YOUR DESK DRAWER. EACH KIT COMES IN IT’S OWN MULTI-COMPARTMENT RECLOSABLE BOX FOR QUICK, EASY SELECTION AND STORAGE. PART NUMBERS FOR THE INDIVIDUAL ITEMS ARE ALSO INCLUDED INSIDE.

MASTER KIT P-1765 - 880 pcs. 459.80JUNIOR KIT P-31136 - 432 pcs. 199.80NUT KIT P-1763 - 60 pcs. 31.90WASHER KIT P-1764 - 68 pcs. 31.90SCREW KIT P-1760 - 376 Pcs. 159.90RING KIT P-1761 - 100 pcs. 39.80PIN KIT P-1762 - 180 pcs. 99.80SPRING KIT P-30326 - 96 pcs. 299.80


PART # PART #

36

Replacement parts for: DAVIDSON 221, 233, 241, 400, 500, 500P, 501 502P, 560, 600,

FILTER SPRING P-12034 4.90

TOGGLE SWITCHESMain drive P-4869 180.00Pump & Drive 500P, 700P P-15305 31.80

UPPER PULLOUT ROLL P-51125 60.00

DETECTOR Sheet feed D-88-2057-01 19.90

SUCTION FOOT D-88-2827-01 17.90

RUBBER SUCTION FOOT ASSEMBLYFor heavy stockComplete D-88-2200-18 46.901) Holder P-50168 32.401) Sucker foot P-5204 2.001) Screw P-50067 9.90

FEEDER GEARS, PAWLS & SPRINGSDrive gear P-50452 179.80Ratchet D-88-1442-01 238.80Feed & stop pawl P-52786 72.50Feed pawl spring P-52718 4.50Stop pawl spring P-52787 5.50

TIMING BELTSLarge (feeder) P-1662 22.90Small (conveyor) P-1656 13.90

KNOB ASSY. Beater bar 500, 600, 700, 500P, 700P3-5/8” P-50541 49.90KNOB ASSY. Beater bar 501, 601, 701, 502P, 702P4-1/2” P-51819 47.50

UPPER FEED ROLL D-88-1719-02or C-310-007567D 99.80

BEARING P-767 5.00

SHEET SEPARATOR or Cat whiskerBrass P-50114 1.00

STOP PAWL SPRING P-52660 13.00

FEEDER RELEASE PAWL P-52786 72.50

ELEVATOR HANDLE ASSEMBLYFeeder P-50955 160.00

ELEVATOR HANDLE ASSEMBLYStacker P-502630 119.90

ELEVATOR HANDLE SHAFTP-50962 12.00

(A) GUIDE Back stop D-88-1333-01 59.90(B) GUIDE L.H. Operators side D-88-1331-02 34.90(C) GUIDE R.H. Non-operators side D-88-1331-03 34.90

STOP FINGER SHAFT ASSEMBLYComplete 500 D-88-5996-03 539.80Complete 700 D-88-5996-04 539.80Shaft with fingers only 500 D-88-6954-01 499.90Shaft with fingers only 700 D-88-6954-02 499.90Timing pulley for both D-88-1372-01 29.90Pin P-441 .60

STRAP ASSEMBLY (7” long strap)Complete D-88-4562-01 39.90(A) Block D-88-2167-01 14.50(B) Knob P-312 4.50(C) Screw P-35 .60(D) Washer P-561 .60(E) Strap D-88-4418-01 8.50 Strap (feeder) P-50420 19.00

STRAP ASSEMBLY (8-5/8” long strap)Complete D-88-2170-01 32.90(A) Block D-88-2167-01 14.50(B) Knob P-312 4.50(C) Screw P-35 .60(D) Washer P-561 .60(E) Strap D-88-2166-01 15.00

MARBLE RETAINER 500 (12-1/2” long) D-88-1760-01 49.90MARBLE RETAINER 700 (19-1/2” long) D-88-1760-03 49.90MARBLE RETAINER 901 (21-1/2” long) D-88-1760-04 49.90MARBLE - 1” Glass P-761 1.30MARBLE - 1” Steel P-759 4.90

CHANNEL ASSEMBLY D-88-2076-01 259.80(A) Rod D-88-2186-01 24.90(B) Nylon ball P-752 3.00(C) Clip D-88-3959-01 9.80(D) Screw P-140 .60(E) Guide D-88-2077-01 219.80

DC

BA

E

E

A

B B

C

PART # PART #


601, 660, 700, 700P, 701, 702P, 760, 901, Dual-a-matic, Mark-I, Roll Converter

COUNTER ASSEMBLY500, 600, 700 D-88-1653-01 119.80702P P-4799 182.90221, 233 D-221-0190 119.80Counter arm D-88-1620-01 21.00

SPRINGS For jogger assemblyOperators side L.H. D-88-2188-01 14.50Non-operators side R.H. D-88-2188-02 14.50

STRAP ASSEMBLY D-88-3173-01 16.50

CONVEYOR TAPE 500, 501, 502P, 600, 700, 701, 702P

P-4990 26.90CONVEYOR TAPE 221, 241 P-3914 41.90

CONVEYOR TAPE Roll Converter P-3913 32.50

SPROCKET ASSEMBLY For conveyorP-8612 90.00

DACRON GEAR For blanket drum gear driveD-88-1396-03 69.90

UNIVERSAL DRIVE SHAFT 500 (for ball bearing or bushing) D-88-1391-01

or D-88-3634-01 199.90 700 (for ball bearing or bushing) D-88-1391-03

or D-88-3634-02 199.90

MAIN DRIVE GEAR For drive shaft (N)ylon or (S)teel500, 600, 700 Dualith D-88-3808-01-N 69.90

D-88-3808-01-S 99.90500P, 700P D-88-4552-01-N 69.90

D-88-4552-01-S 69.90501,601,701,502P,702P D-88-6728-01-N 79.90

D-88-6728-01-S 79.90

••• The nylon gear is double wide & designed to preserve the life of your other gears. Just turn it around and reuse it. Twice the life span as original design and your machine will run up to 50% quieter.

BLANKET HUB ASSEMBLYReinforced lip for durability & longer life.

D-88-3928-01 179.90

BLANKET CYLINDER GEARGear with keys D-88-1608-01 299.80Gear only D-88-1610-01 254.00Keys D-251-0088 24.00Screws P-1892 3.20

BLANKET DRUM GEAR COUPLING500, 600, 700 D-88-1615-01 96.00502P, 702P D-88-1615-02 119.90221, 251, 233 Top plate cylinder coupling

D-251-0105 104.90500P, 700P D-88-4377-01 259.90

PLATE SEGMENT CLAMPD-88-2597-01or D-88-2597-02 13.50

Screw P-57 .60

STUD For blanket drum latchD-88-1635-01 15.80

DACRON, NYLON & ALUMINUM GEARS500, 600, 700 Off large cylinder gearNYLON D-88-1499-01

or D-88-3083-02 69.90ALUMINUM D-88-1499-X1 69.90501, 601, 701 Off large cylinder gearDACRON C-306-009847D 69.90

500, 600, 700 Off ink unitNYLON D-88-1552-01 89.90ALUMINUM D-88-1552-X1 99.90501, 601, 701, Off ink unitDACRON D-88-6720-01 69.90

GEAR For ink vibrator roll501, 601, 701 C-120-004904D 107.40

CHROME DRAW SHEETS500 - 13” (no bend) D-88-2321-01 59.90500 - 14” (with bend) D-88-2321-02 59.90600 - 11” (no bend) D-88-2321-09 115.90700 - 13” (no bend) D-88-2321-05 69.90700 - 14” (with bend) P-30788 79.90901 - 14” (with bend) C-199-006704D 90.00

PACKING SHEETS500, 501(.005) - 13” D-221-0415 4.90(.008) - 13” D-221-0416 4.90(.010) - 13” D-221-0417 4.90(.005) - 14” D-227-0006 4.90(.008) - 14” D-227-0007 4.90(.010) - 14” D-227-0008 4.90700, 701(.005) - 13” D-233-0048 4.90(.008) - 13” D-233-0049 4.90(.010) - 13” D-233-0050 4.90(.005) - 14” D-233-0189 4.90(.008) - 14” D-233-0190 4.90(.010) - 14” D-233-0191 4.90901(.005) - 14” C-199-006635D 4.90(.010) - 14” C-199-006634D 4.90

PIN BAR For plate & impression segment500, 600, 700 C-125-007223D 159.80


PART # PART #

38

Replacement parts for: DAVIDSON 221, 233, 241, 400, 500, 500P, 501 502P, 560, 600,

EXTENSION BAR For impression segment700, 601, 701, 700P D-88-2822-03 99.90

DUCTOR ROLLER CLIPInk & water D-88-0804-01 7.80

DUCTOR SPRING LATCH For roller bracketInk & water D-88-2606-01 7.90

WASH UP BLADES For Baldwin wash up units500, 501 (11-3/4 x 2-1/4, 4 Holes, Steel & rubber) D-88-5200-02 49.90700, 701 (18-3/4 x 2-1/4, 5 Holes, Steel & rubber) D-88-5200-01 49.90901 (20-3/4 x 2-1/4, 6 Holes, Steel & rubber) D-88-5200-03 69.90

NOTE: WASH UP UNITS ALSO AVAILABLE

INK FOUNTAIN BLADE500, 501, 502P D-88-1574-01 76.50600, 601, 700, 701, 702P D-88-1574-03 89.90901 D-88-1574-04 88.00

FROG ASSEMBLY For dampening system501, 601, 701Complete D-88-6656-01 63.80(A) Wiper D-88-6607-01 9.90(B) Screw P-1871 .60(C) Lock washer P-644 .60(D) Frog D-88-6606-01 49.90(E) Thumb screw P-312 4.50

SMALL PNEUMATIC CYLINDERFor jogger blower manifold

D-88-1857-01 49.90

STRIPPER PLATE For chain delivery section600, 601, 700, 701, 702P D-88-2649-02 99.90

GEARED DAMPENING ROLLER500 Complete D-88-1469-07 559.80501 Complete D-88-1469-09 579.80700 Complete D-88-1469-08 579.80Roller and shaft only 500, 501 D-88-1468-05 499.90Roller and shaft only 700 D-88-1468-06 519.80Gear 500, 700 D-88-1462-01 79.90Gear 501 D-88-6724-01 130.00Screw for all P-50 .60

B&C

A

D

E

RUBBER STOP For Roll Converter paper stop assy.D-33-0504-01 4.00

JOGGER PLATE ASSEMBLIES 500, 600, 700 (Non-operators side) D-88-1916-02 91.20 (Operators side) D-88-1915-02 91.20

(Rear) D-88-1913-04 or D-88-1893-01 72.00

501, 601, 701 (Rear) D-88-1893-03 72.00

PAWL ASSEMBLYFor pile jogger assy. D-88-1863-02 59.90

CONTROL HANDLE ASSEMBLY(A) 500P, 700P (not shown) D-88-5363-01 69.80(B) 501, 502P, 701, 702P D-88-5363-03 104.00(C) 500, 700 D-88-1451-01 79.80(D) 501, 601, 701 D-88-5363-02 93.80

CONNECTING LINK ASSEMBLY (L.H. & R.H.)500, 600, 700 D-88-4148-01 79.90501, 601, 701, 702P P-8744 99.90

OLD STYLE CONNECTING LINK Only(A) D-88-2817-01 10.50

GRIPPER BAR LINK Only 500, 600, 700(B) Operators side L.H. D-88-2533-01 38.00(B) Non-operators side R.H. D-88-2818-01 38.00

GRIPPER BAR CARR. LINK Only 501, 601, 701, 502P, 702P(B) Operators side L.H. P-8722 64.90(B) Non-operators side R.H. P-8721 64.90

GRIPPER BAR LINK Only 901(B) Operators side L.H. C-399-006720D 87.00(B) Non-operators side R.H. C-399-006719D 87.00

NEW STYLE CONNECTING LINK Only(A) P-8749 9.00

JOGGER SPRING & BLOCK ASSEMBLY - ConveyorComplete D-88-2178-02 79.80(A) Block only D-88-1968-01 29.90(B) Thumb screw P-312 4.50(C) Screw P-194 .60(D) Lockwasher P-623 .60(E) Spring - Left hand D-88-2188-02 14.50(F) Spring stop D-88-2187-02 5.50(G) Clip D-88-2286-01 8.90(H) Spring - Right hand D-88-2188-01 14.50

C DB

A

B

B

A

H

EF

GC&D

PART # PART #


601, 660, 700, 700P, 701, 702P, 760, 901, Dual-a-matic, Mark-I, Roll Converter

REPAIR KITS FOR ALL DAVIDSONS

••• ELIMINATE COSTLY DOWN TIME WITH YOUR OWN EMERGENCY KIT FOR YOUR MODEL PRESS.

Master kit P-1771 - 1053 pcs. 439.80Nut kit P-1769 - 87 pcs. 44.80Washer kit P-1770 - 79 pcs. 44.80Screw kit P-1766 - 447 pcs. 225.80Ring kit P-1767 - 105 pcs. 39.80Pin kit P-1768 - 234 pcs. 119.80Spring kit P-30327 - 101 pcs. 239.90

GRIPPER CHAINS (set of 2 only)221, 251, 500, 700 P-8929 74.90501, 601, 701, 502P, 702P, 901 P-8935 92.90

SAVE MONEY BY REPLACING ONLY THE PARTS THAT WEAR INSTEAD OF REPLACING THE WHOLE GRIPPER BAR ASSEMBLY.

GRIPPER BAR REPAIR KIT - 500, 501, 502 P-30739 89.90Consists of:(C) Gripper finger-qty. 4, (D) Spring-qty. 4, (E) Cam-qty. 1,(F) Ret. ring-qty. 1,(G) Spiral pin-qty. 8, (H) Ret. ring-qty. 1,(I) Cam roller-qty. 1, (J) Ret. ring-qty 1.

GRIPPER BAR REPAIR KIT - 700, 701, 702 P-30740 139.90Consists of:(C) Gripper finger-qty. 8, (D) Spring-qty. 8, (E) Cam-qty. 1,(F) Ret. ring-qty. 1, (G) Spiral pin-qty. 8, (H) Ret. ring-qty. 1,(I) Cam roller-qty. 1, (J) Ret. ring-qty 1.

GRIPPER BAR REPAIR KIT - 901 P-30744 162.90Consists of:(C) Gripper finger-qty. 8, (D) Spring-qty. 8, (E) Cam-qty. 1,(F) Ret. ring-qty. 1, (G) Spiral pin-qty. 8, (H) Ret. ring-qty. 1,(I) Cam roller-qty. 1, (J) Ret. ring-qty 1.

NOTE: REFERENCE ALL KEY NUMBERS ON THESE THREE REPAIR KITS TO GRIPPER BAR ASSEMBLIES IN THE NEXT COLUMN.

F

I

H

C EJ

DG

GRIPPER BAR ASSEMBLY

••• MADE OF REINFORCED STEEL TO PREVENT BOWING.••• UNIVERSAL - MAY BE USED FOR STANDARD OR SLITTER.

500 Complete (slitter not avail.) D-88-2832-14 719.80(A) Anvil (standard) D-88-6945-01 469.90(B) Shaft D-88-6385-02 149.90(C) Finger D-88-2518-01 13.00(D) Spring C-199-006219D 6.90(E) Cam roller P-1445 7.20(F) C-Ring P-668 .60(G) Spiral pin P-345 .60(H) C-Ring P-682 .60( I ) Cam roller P-1407 9.00(J) Retaining ring P-700 .60

501, 502P Complete (slitter not avail) D-88-2832-15 719.80(A) Anvil (standard) D-88-6945-02 459.90(B) Shaft D-88-6385-02 149.90(C) Finger D-88-2518-01 13.00(D) Spring C-199-006219D 6.90(E) Cam roller P-1445 7.20(F) C-Ring P-668 .60(G) Spiral pin P-345 .60(H) C-Ring P-682 .60( I ) Cam roller P-1407 9.00(J) Retaining ring P-700 .60

700 Universal - fits standard or slitterComplete p-700990 799.80(A) Anvil (slitter) D-88-8037-01 559.90(B) Shaft D-88-6385-04 149.90(C) Finger D-88-2518-01 13.00(D) Spring C-199-006219D 6.90(E) Cam roller P-1445 7.20(F) C-Ring P-668 .60(G) Spiral pin P-345 .60(H) C-Ring P-682 .60( I ) Cam roller P-1407 9.00(J) Retaining ring P-700 .60

600, 700P Universal - fits standard or slitter 701, 702P Complete D-88-2832-12 799.80

(A) Anvil (slitter) D-88-8037-02 559.90(B) Shaft D-88-6385-04 149.90(C) Finger D-88-2518-01 13.00(D) Spring C-199-006219D 6.90(E) Cam roller P-1445 7.20(F) C-Ring P-668 .60(G) Spiral pin P-345 .60(H) C-Ring P-682 .60( I ) Cam roller P-1407 9.00(J) Retaining ring P-700 .60

901 Complete (slitter not avail.) C-399-006713D 999.80(A) Anvil (standard) C-125-006722D 799.90(B) Shaft C-311-006714D 180.00(C) Finger C-117-006727D 12.80(D) Spring C-139-006747D 6.90(E) Cam roller P-1445 7.20(F) C-Ring P-668 .60(G) Spiral pin P-3045 .60(H) C-Ring P-667 .60(I) Cam roller P-1407 9.00(J) Retaining ring P-700 .60

E

HF

I C B D G J

A


PART # PART #

40

Replacement parts for: BAUM FOLDER, MBM, MARTIN YALE, PROFOLD, VARN KOMPAC

TIRES(In order of O.D. x I.D. x Width) Caliper tire (1-11/16” x 15/16” x 1/2”) B-3750 7.90 Roller tire (1” x 15/32” x 1”) B-45290 4.75 Roller tire (1-13/16” x 1-3/32” x 1”) B-48429 6.35 Tire sucker wheel (1-3/4” x 1-7/16” x 1/4”) B-50080 7.60

PERFORATING WHEEL6 Tooth B-7618 12.9015 Tooth B-7895 16.5518 Tooth (shown) B-7896 16.5524 Tooth B-7619 10.9531 Tooth B-6798 12.5541 Tooth B-7791 8.7564 Tooth B-11962 12.50

STACKER BELT B-6346 301.00

REGISTER TAPE1” X 73” P-3905 21.90

FEED REPAIR TAPES (Set of 4)

For SOLNA / EAGLE / CHIEF25/25-1 ProfiteerP-30002 89.90

STRIPPER B-6438 13.25

SHEET DETECTOR TAB - Amber coloredFor vacuum feed B-50498 4.90

FEED ROLLER - For 52 / 58 AB DICK FOLDERTan tire P-31067 23.90Black tire P-31068 10.50

TIRE KIT For Baum Folder 714B-48429-K 17.45Consists of:1) B-45290 Tire (each) 4.752) B-48429 Tire (each) 6.35

TIRE KIT For Baum Folder 417, 200, 400, 600, Mark I, Mark II, Junior Jet, AutosetB-6402-K 19.90Consists of:8) B-6402 Tire (each) 2.65

TIRE KIT For Baum FolderB-3750-K 29.90Consists of:4) B-3750 Caliper tire (each) 7.90

COLLARS For Baum Folder

(A) 7/8 I.D. x 1-1/2 O.D. x 5/8 THK. B-6411 27.90(B) 7/8 I.D. x 1-3/4 O.D. x 5/8 THK. B-7780 17.10

TOP PERFORMANCE KIT For MBM Fastfold 17MI-1 132.70Consists of:3) MI-AA1462 Auto feed wheels 20.552) MI-AA1121 Rubber wheels 23.551) MI-AA1077 Abrasive stone with flap 24.35

TOP PERFORMANCE KIT For Martin YaleMY-1 87.90Consists of:1) MY-W-0008015 Feed roll for M-Y Friction folder1) MY-M-0003548 Feed rubber for 12 x 17 folder1) MY-M-0095138 Drive friction1) P-11215 Bushing2) MY-M-0003080 Accessory rubber

for MY Friction folder

TOP PERFORMANCE KIT For Profold 1117FM, 1117BM, 1118FMPF-1 62.90Consists of:1) PF-109696 Feed wheel tire 10.152) B-3750 Pull out tires (each) 7.902) PF-109777 Slides (each) 15.601) PF-109624 Stationary roller 9.90

TEFLON SEALS FOR VARN KOMPAC Old style (set of 2) P-30083 9.80 New style (set of 2) P-30093 9.80 Old style (5 pack) P-30724 46.00 New style (5 pack) P-30714 46.00 Old style (10 pack) P-30725 90.00 New style (10 pack) P-30715 90.00FELT CLEANING SEALSSet of 6 (2 seals per set) P-11743 9.50Set of 12 (2 seals per set) P-11744 17.00

BACKING PLATE KITHas both Left Hand and Right Hand assembly.

V-92380 38.55

GEAR & CLUTCH ASSEMBLY For Varn1250 Multilith V-12404-1/4 58.90360, 375, 9800 V-36404-5/16 58.90360 V-36404-7/16 58.901360, 1650 V-13404-17/32 58.90

SYRINGE - 2.5 OZ.

P-30088 2.00

DRILL BLOCKS For Challenge1-1/2” Diameter P-30811 3.303” Diameter P-30812 3.50

DUROWEAVE “VELOUR DAMPENING COVERS”

• THEY LAST FOR MONTHSThe special yarn that is used gives Duroweave covers the ability to shrink to a snug fit on your roller. The weave is a continuous wrap—no seams to come loose.

• THEY’RE EASY TO CLEANDuroweave covers can be cleaned off in your shop sink under warm water. No need for expensive attachments or equipment.

• THEY’RE LINT AND PATTERN FREEThe surface loops of the knit are evenly sheared to provide a uniform pile height across the roller length and are guaranteed to be 100% lint free—no

contaminating fibers. The covers have a seamless knit for pattern free printing.

AVAILABLE FOR ALL MODELS.

AB DICK360 NEW STYLE SOFT RUBBER INK ROLLER KITP-5004 216.15Consists of 5 rollers

1) P-36010 Upper form (measure diameter)1) P-36011 Lower for (measure diameter)2) P-36021 Distnbutor (measure diameter)1) P-36030 Ductor

375, 9800 SOFT RUBBER INK ROLLER KITP-5021 240.25Consists of 5 rollers

1) P-37010 Upper for (measure diameter)1) P-37011 Lower form (measure diameter)2) P-37021 Distributor (measure diameter)1) P-37030 Ductor

MULTILITH1250W, LW, 2650W OLD STYLE SOFT RUBBER INK ROLLER KITP-5046 205.95Consists of 6 rollers

1) P-12130 Ductor (measure rubber to rubber3) P-12121 Distributor (measure diameter, rubber to rubber &

shaft to shaft)2) P-12110 Form (measure rubber to rubber)

1250W, LW, N, 2850W NEW STYLE SOFT RUBBER INK ROLLER KITP-5037 180.70Consists of 5 rollers

1) P-12230 Ductor2) P-12221 Distributor (measure diameter, rubber to rubber &

shaft to shaft)2) P-12210 Form (measure rubber to rubber)

CHIEF15, 115, 215, 1st. head / Itek 1115 SOFT RUBBER INK ROLLER KITP-30452 300.15Consists of 6 rollers

2) P-15011 Form2) P-15021 Top & bottom idler1) P-15020 Back idler1) P-15031 Ductor (measure shaft to shaft)

17 SOFT RUBBER INK ROLLER KITP-30450 321.50Consists of 6 rollers

2) P-17011 Form2) P-17021 Top & bottom idler1) P-17020 Back idler1) P-17030 Ductor

DAVIDSON400, 500, 501, 500P, 501P, 502P NEW STYLEP-30408 237.30Consists of 5 rollers

1) P-50110 Upper ink form (measure overall shaft length)1) P-50111 Lower ink form (measure overall shaft length)2) P-22020 Ink distributor & ductor1) P-22022 Front ink distributor (with offset bearings)

P-30415 318.10Consists of 5 rollers

1) P-70110 Upper form (measure shaft to shaft)1) P-70111 Lower form (measure shaft to shaft)2) P-23020 Distributor & Ductor1) P-23022 Front distributor

HAMADA600 & 600CD SOFT RUBBER INK ROLLER KITP-30426 258.40Consists of 5 rollers

1) P-10610 Small upper form1) P-10611 Large lower form2) P-10620 Distributor (measure diameter)

(bushings not included)1) P-10630 Ductor (bushing not included)

700, 700CD (O.S. & N.S.) SOFT RUBBER INK ROLLER KITP-30432 387.05Consists of 6 rollers

1) P-10110 Small upper form1) P-10111 Large upper form2) P-10120 Distributor (measure diameter & overall shaft length)

bushings not included.1) P-10130 Ductor (bushings not included)1) P-10121 Distributor (measure diameter & shaft to shaft)

bushings not included.

RYOBI / ITEKRyobi 2800 / Itek 960 SOFT RUBBER INK ROLLER KITP-30445 253.70Consists of 5 rollers

1) P-28010 Small upper form1) P-28011 Large lower form2) P-28020 Distributor (measure diameter)1) P-28030 Ductor (measure shaft to shaft)

Ryobi 3200 / Itek 960 SOFT RUBBER INK ROLLER KITP-30446 271.75Consists of 5 rollers

1) P-32R11 Small upper form1) P-32R12 Large lower form2) P-32R20 Ink distributor (measure rubber to rubber)1) P-32R33 Ductor (N.S.) (measure shaft to shaft)

HEIDELBERGGTO 46 SOFT INK RUBBER ROLLER KITP-30457 741.85Consists of 9 rollers

1) P-46H10Y Form1) P-46H10B Ductor1) P-46H10W Form1) P-46H10R Form4) P-46H10B Distrubutor1) P-46H10B Ductor

GTO 46 SOFT RUBBER WATER ROLLER KITP-30458 249.40Consists of 3 rollers

2) P-46H10G Form1) P-46H10G Ductor

GTO 52 SOFT RUBBER INK ROLLER KITP-30459 810.55Consists of 9 rollers

1) P-52H10Y Form1) P-52H10B Form1) P-52H10W Form1) P-52H10R Form4) P-52H10B Distributor1) P-52H10B Ductor

GTO 52 SOFT RUBBER WATER ROLLER KITP-30460 278.75Consists of 3 rollers

2) P-52H10G Form1) P-52H10G Ductor

NOTE: Please measure diameter and rubber to rubber on distributors before ordering.

41

ALL ROLLER KITS ON $ALE

Part # Model # Ply Edges SizeA.B. DICKP-30054 . . . . . . . . . . . . . 360 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 8 hole. . . . . . . . . . . . . . . . . . . 18-1/2 x 10-5/8P-30055 . . . . . . . . . . . . . 360 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 8 hole. . . . . . . . . . . . . . . . . . . 18-1/2 x 11P-30057 . . . . . . . . . . . . . 9800 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 10 hole . . . . . . . . . . . . . . . . . . 19-3/16 x 12-5/8P-30059 . . . . . . . . . . . . . 385 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 12 hole . . . . . . . . . . . . . . . . . . 18-3/4 x 22-5/8P-31256 . . . . . . . . . . . . . 9880 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 14 hole . . . . . . . . . . . . . . . . . . 19-1/4 x 22-3/4P-31418 . . . . . . . . . . . . . QP254 . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-3/16 x 12-5/8CHIEFP-30061 . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 13 hole . . . . . . . . . . . . . . . . . . 15-3/16 x 10P-30064 . . . . . . . . . . . . . 17 . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 4 hole. . . . . . . . . . . . . . . . . . . 19-13/16 x 12-5/8DAVIDSONP-30068 . . . . . . . . . . . . . 700 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 13 hole . . . . . . . . . . . . . . . . . . 16 x 17-1/4P-30066 . . . . . . . . . . . . . 500 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 13 hole . . . . . . . . . . . . . . . . . . 16 x 10P-30067 . . . . . . . . . . . . . 600 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 23 hole . . . . . . . . . . . . . . . . . . 13-3/16 x 17-1/4P-30544 . . . . . . . . . . . . . 700 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 23 hole . . . . . . . . . . . . . . . . . . 16 x 18P-30070 . . . . . . . . . . . . . 901 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 26 hole . . . . . . . . . . . . . . . . . . 16-1/16 x 19-3/4HAMADAP-30072 . . . . . . . . . . . . . 500 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 5 hole. . . . . . . . . . . . . . . . . . . 16-1/2 x 10-1/2P-30533 . . . . . . . . . . . . . E47 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 7 hole. . . . . . . . . . . . . . . . . . . 16-5/16 x 18-3/8P-30074 . . . . . . . . . . . . . 600 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 5 hole. . . . . . . . . . . . . . . . . . . 19-1/8 x 12P-31261 . . . . . . . . . . . . . 600/665 . . . . . . . . . . 3 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-13/16 x 12P-31430 . . . . . . . . . . . . . DU34 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-3/16 x 12-1/2P-30538 . . . . . . . . . . . . . H234 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-7/8 x 13-1/8P-30079 . . . . . . . . . . . . . 800 . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 8 hole. . . . . . . . . . . . . . . . . . . 16-11/32 x 20-1/4P-31150. . . . . . . . . . . . . . C248 . . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 16-5/16 x 18-1/2P-30597 . . . . . . . . . . . . . H234 . . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-7/8 x 12-5/8P-31254 . . . . . . . . . . . . . RS34 . . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-7/8 x 12-5/8P-31282 . . . . . . . . . . . . . C252 . . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 16-3/8 x 20-1/8P-31290 . . . . . . . . . . . . . 452 . . . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 17-3/4 x 20-1/4HEIDELBERGP-30557 . . . . . . . . . . . . . KORD 64 . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 20-5/8 x 26-1/2P-30558 . . . . . . . . . . . . . MO. . . . . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 22-1/4 x 26-1/2P-30562 . . . . . . . . . . . . . KORS . . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 23 x 29-3/8P-30563 . . . . . . . . . . . . . SOR. . . . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 27-1/8 x 33-1/2P-30564 . . . . . . . . . . . . . SORD . . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 28-1/8 x 36-1/4P-31271 . . . . . . . . . . . . . SM 102 . . . . . . . . . . 4 . . . . . . . . . . . . . . U bars . . . . . . . . . . . . . . . . . . 32-5/8 x 41-1/8P-30566 . . . . . . . . . . . . . SM 102 . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 31-1/8 x 41-3/8P-31422 . . . . . . . . . . . . . MO. . . . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 23-3/4 x 29-3/8P-30550 . . . . . . . . . . . . . TOK . . . . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 16 x 10-1/2P-30551 . . . . . . . . . . . . . GTO 46 . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 17-5/16 x 18-1/8P-30552 . . . . . . . . . . . . . GTO 52 . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 17-1/2 x 20-1/2P-30552-B . . . . . . . . . . . . GTO52 . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 17-1/2 x 20-1/2P-31257 . . . . . . . . . . . . . SM 52 . . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 18-1/8 x 21-1/16P-31287 . . . . . . . . . . . . . QM 46DI . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 21-7/8 x 13-1/4P-30790 . . . . . . . . . . . . . QM 46 . . . . . . . . . . . 4 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 21-7/8 x 13-1/4P-30555 . . . . . . . . . . . . . KORA . . . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 20-1/4 x 23-5/8P-30510 . . . . . . . . . . . . . KORD 62 . . . . . . . . . 4 . . . . . . . . . . . . . . straight . . . . . . . . . . . . . . . . . . 20-1/4 x 24-5/8MULTILITHP-30043 . . . . . . . . . . . . . 1250 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 9 hole. . . . . . . . . . . . . . . . . . . 15-3/16 x 10P-30045 . . . . . . . . . . . . . 1250W . . . . . . . . . . . 3 . . . . . . . . . . . . . . 17 hole . . . . . . . . . . . . . . . . . . 16-1/16 x 10-5/8P-30050 . . . . . . . . . . . . . 1850 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 30 hole . . . . . . . . . . . . . . . . . . 16-1/16 x 17-5/8RYOBIP-30081 . . . . . . . . . . . . . 2700 . . . . . . . . . . . . 5 . . . . . . . . . . . . . . 8 hole. . . . . . . . . . . . . . . . . . . 18-1/32 x 10-5/8P-30082 . . . . . . . . . . . . . 2800 . . . . . . . . . . . . 5 . . . . . . . . . . . . . . 8 hole. . . . . . . . . . . . . . . . . . . 18-15/16 x 11-1/4P-30084 . . . . . . . . . . . . . 2800XL . . . . . . . . . . 5 . . . . . . . . . . . . . . 8 hole. . . . . . . . . . . . . . . . . . . 19-1/2 x 11-1/4P-30085 . . . . . . . . . . . . . 3200 . . . . . . . . . . . . 5 . . . . . . . . . . . . . . 10 hole . . . . . . . . . . . . . . . . . . 18-15/16 x 12P-30086 . . . . . . . . . . . . . 3200LC . . . . . . . . . . 5 . . . . . . . . . . . . . . 10 hole . . . . . . . . . . . . . . . . . . 19-1/2 x 12P-30086-B . . . . . . . . . . . . 3200LC . . . . . . . . . . 5 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-1/2 x 12P-30087 . . . . . . . . . . . . . 3200MCD/LC . . . . . . 5 . . . . . . . . . . . . . . 12 hole . . . . . . . . . . . . . . . . . . 19-1/2 x 13P-30589 . . . . . . . . . . . . . 3200PFA . . . . . . . . . 5 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-1/8 x 12-1/4P-30091 . . . . . . . . . . . . . 3302 . . . . . . . . . . . . 5 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-3/8 x 13-5/8P-30568 . . . . . . . . . . . . . 3302M . . . . . . . . . . . 5 . . . . . . . . . . . . . . bars . . . . . . . . . . . . . . . . . . . . 19-1/2 x 13-5/8P-30531 . . . . . . . . . . . . . 3302M . . . . . . . . . . . 5 . . . . . . . . . . . . . . 12 hole . . . . . . . . . . . . . . . . . . 19-1/2 x 13-5/8P-30092 . . . . . . . . . . . . . 480/500 . . . . . . . . . . 5 . . . . . . . . . . . . . . 7 hole. . . . . . . . . . . . . . . . . . . 19-1/8 x 16-7/8

This is just a small sample of our inventory. Call for more part information.

42

INK WASH UP ATTACHMENTS • FOLDERS • PARTS FOR LARGE AND SMALL FOLDERS • AUTOMATIC DAMPENING UNITS • PAPER CUTTERS • PAPER DRILLS • PAPERW

E A

LSO

HAV

E A

WID

E V

AR

IETY

OF

ATTA

CH

ME

NTS

AN

D A

CC

ES

SOR

IES

INC

LUD

ING

• SP

RAY

UN

ITS

AN

D P

OW

DER

S •

ANTI

TR

ACK

ING

WH

EELS

• LI

GH

T TA

BLE

S •

LAM

PS • JO

GG

ER

S • E

LECTR

IC STA

PLER

S • S

ECO

ND

CO

LOR

HE

AD

S • S

WIN

G AW

AY B

RA

CK

ETS • NU

MB

ERIN

G U

NITS • R

EPA

IR K

ITS • AN

D M

UC

H M

OR

E! CA

LL US A

ND

AS

K

CALL US FOR MANY “HARD TO FIND” PARTS.WE HAVE OVER 100,000 DIFFERENT ITEMS IN STOCK NOW!

PRINTER’S PARTS STORE14201 N HAYDEN RD #B4

SCOTTSDALE, AZ 85260800-922-2425

FAX 480-922-8550 www.azpressparts.com / [email protected]

PRESORTEDSTANDARD

U.S. POSTAGE PAIDRUTHERFORD, NJPERMIT NO. 348

ASK US ABOUT OUR REPLACEMENT PARTS MANUALSFor A.B Dick chute and chain deliveries - 350, 360, 375, 9800, and (385 Chain delivery only)

For Multilith chute and chain deliveries - 1250, 1250W, 1250LW, 1250N, 1250Domestic.For Chief / Gestetner 15, 115, 215, 17, 117, 217, Super Chief 2000, X-series / 211, 213, 311, 312, 313

VACUUM PUMP REPAIR KITS

Consists of all parts neccessary to repair your vacuum pump.

For A.B. Dick 350, 360, 375, 9800P-1182

For A.B. Dick 380, 385 (Air - Vac pumps only)P-1930

For Multilith 1250’sP-1961

For Chief 15, 115, 215, 17, 117, 217 & Davidson 500, 600, 700, series.

P-1960

OFFSET DUPLICATOR LAMPS

COMES WITH UNIVERSAL MOUNTING HARD-WARE, HAS A FLEXIBLE NECK AND CAN USE UP TO 100 Watt BULB.

Includes mounting kit, stud, washer, shoulder nut, nylock nut, and cord.

For A.B. Dick, Multilith, Chief, Davidson, and RyobiP-1956

REPAIR / TROUBLESHOOTING VIDEOSTHIS OLD PRESSA professionally made film documenting repairs for the A.B. Dick 350, 360, 375, and 385 presses, and for the Multilith 1250, 1250LW, 1250N, and 1850 presses.VHS-A.B. Dick (English) P-1714VHS-Multilith (English) P-1715VHS-A.B. Dick (Spanish) P-30006VHS-Multiltih (Spanish) P-30005VHS-Ryobi (English) P-31070

PRO-TIPS2 tapes with 120 minutes of advanced pressman techniques plus workbook for the A.B. Dick 350, 360, 9800, and 385 presses.VHS P-1717

DON’T LET DOWN TIME PICK YOUR POCKET!

A BROKEN SCREW OR PIN CAN CAUSE YOUR MACHINE TO BE DOWN AND COST YOU TIME AND MONEY.

“QUICK FIX REPAIR KITS” FOR ALL MODELS:A.B. DICK, CHIEF, DAVIDSON, GESTETNER, HAMADA, HEIDELBERG, MULTILITH, RYOBI/ITEK.

**** CALL FOR MORE INFO AND PRICES.

Order Form Date:

Company:

Address:

City/Zip/Postal Code:

State/Province:

Phone:

Fax:

Contact Name:

Deliver To Same as Above

Company:

Address:

City/Zip/Postal Code:

State/Province:

Phone:

Fax:

Contact Name:

PRINTERS PARTS STORE82 Herman St

E Rutherford, New Jersey 07073 USA

Phone: 201-935-9595Fax: 800-392-4072 or 201-935-5333

www.ppsnj.com e-mail: [email protected]

E-mail

Country

Order Number:

Ship Date:

Internal Use Only

PO #

* Certain supplies are taxable if shipped within the State of New Jersey & will be invoiced accordingly.

Payment

Checks-By-Fax: Fax to 201-935-9595

Credit Card

American Express

Mastercard

Visa

Card Number:

Expiration Date:

Cardholder Name:

Data is not secure.

CVV2 Code:

Data is not secure. You may print and fax to 201-935-5333.

Address

City State Zip Code

Country

Standard Shipping Charges UPS Ground (except for chemicals, HAZMAT & equipment; heavy & oversized items may require additional shipping charges ). $10.50 Visa, Master Card, American Express, Checks-by-Fax, Paypal, Pre-Paid; COD: $19.50; Overnight/Next Day Air, 2nd Day Air & 3Day Air Available Upon Request. International Orders: Actual Shipping/Freight Charges Apply. We will notify you of freight charges. Shipping Method for International Orders (please check one):

UPS Fed-Ex USPS Express Mail DHL

Account #

Item / Part Number Description Quantity Unit Price Amount

Sub-total

Grand Total

Freight

*NJ Sales Tax 7%

az press parts catalog

Documents

valve p

feeder p

counter p

gear p

steel p

wheel p

center p

seriesshaft p