ba ttk 400 - satema€¦ · en operating manual – dehumidifier ttk 400 4 technical data power...

TTK 400

OPERATING MANUALDEHUMIDIFIER

EN

TRT-

BA

-TTK

400-

TC-0

02-E

N

SymbolsHazardous electric current!Warns about hazards from electric current which can lead to injuries or even death.

Danger!Warns of a hazard which can lead to personal injury.

Caution!Warns of a hazard which can lead to damage to prop-erty.

The current version of the operating manual can be found at:

Legal noticeThis release replaces all previous releases. No part of this publi-cation may be reproduced without written permission. The same applies for electronically processing, duplicating or spreading the publication. Subject to technical changes. All rights reserved. Trademarks are used without guarantee that they may be used freely and primarily following the spelling of the manufacturer. The product names used are registered and should be treated appro-priately. The scope of delivery may vary from product images. This document was produced with all due care. We accept no liability whatsoever for mistakes or omissions. © Trotec

Table of contents

Notes regarding the operating manual ............................ 01Safety ............................................................................. 02Information about the device........................................... 03Transport ........................................................................ 07Operation........................................................................ 08Errors and faults ............................................................. 11Maintenance ................................................................... 12Disposal.......................................................................... 17Declaration of conformity ................................................ 17

Notes regarding the operating manual

TTK 400

http://download.trotec.com/?sku=1120000400&id=1

1 Operating Manual – Dehumidifier TTK 400 EN

Read this manual carefully before starting or using the device. Store the manual near the device or its site of use!

• Do not use the device in potentially explosive rooms.• Do not use the device in atmospheres containing oil, sulphur,

chlorine, acid or salt.• Do not operate the device in rooms containing acetone, undi-

luted acids or solvents.• Set the device up in an upright and stable position.• Do not expose the device to a direct jet of water during opera-

tion.• Ensure that the air inlet and outlet are not obstructed.• Ensure that the suction side is kept free of dirt and loose ob-

jects.• Never reach or put objects into the device.• Do not cover or transport the device during operation.• Do not sit on the device.• Ensure that all electric cables outside of the device are protect-

ed from damage (e.g. caused by animals).• Observe the device's power input, cable length and intended

use when selecting extensions to the connecting cable. Avoid electrical overload.

• Only transport the device in an upright position and when the condensate pump and condensation tray are empty.

• Dispose of the collected condensate. Do not drink it. Health hazard!

Intended useOnly use the device TTK 400 as a mobile industrial dryer for drying and dehumidifying room air, while adhering to and following the technical data.

Intended use comprises: • drying and dehumidifying:

– production plants, underground rooms– store rooms, archives, laboratories– rooms and areas after water damages from burst pipes or

flooding• maintaining the dryness of:

– instruments, devices, files– electric control devices, boiler plants, turbines and pipe sys-

tems in power plants– moisture-sensitive loads etc.

Improper useDo not place the device on flooded ground. Do not use the device outdoors. Do not place any objects on the device for drying. Any changes, modifications or alterations to the device which have not been authorised by Trotec are forbidden.

Personnel qualificationsPeople who use this device must:• be aware of the dangers that occur when working with electric

devices in damp areas.• take measures to protect themselves from direct contact with

live parts.• have read and understood the operating manual, especially the

chapter Safety.

Maintenance tasks at the electrical equipment or the air-conditioning technology must only be carried out by specialist companies for cooling and air-conditioning or by Trotec.

Residual risksHazardous electric current!Work on the electrical components must only be carried out by an authorised specialist company!

Hazardous electric current!Before any work on the device, remove the mains plug from the mains socket!

Caution!To avoid damages to the device, never operate the device without an inserted air filter!

Danger!Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!

Danger!The device can cause injuries if it falls over! Tilt the device only slightly and move it carefully. If necessary, ask another person to help you. For longer distances, transport the device with a fork lift or pallet jack. Never stand below the device when it is suspended.

Behaviour in the event of an emergency1. Disconnect the device from the mains in the event of an emer-

gency.2. Do not reconnect a defective device to the mains.

Safety

EN Operating Manual – Dehumidifier TTK 400 2

Device descriptionThe device uses the principle of condensation to automatically dehumidify rooms. It can be used in continuous operation.The fan sucks in humid room air through the air inlet (2), the air filter (5), the evaporator and the condenser located behind it. The air is cooled at the cold evaporator until it is below the dew point. Water vapour contained in the room air precipitates on the evapo-rator fins as either condensation or rime. The dehumidified, cooled air is warmed again and blown out via the air outlet (8). The drier air thus conditioned mixes with the air in the room. The humidity in the room where the device is positioned is reduced as air con-stantly circulates through the device. Depending on the air tem-perature and the relative humidity, the condensed water either drops into the condensation tray continuously or only during the defrost phases. The condensate is fed through a pressure-resist-ant pipe connection and out of the device via the pre-assembled condensation drain hose (7).

The condensed water can be discharged using a retrofitted con-densate pump.

For easy operation and transport, the device is fitted with a mains switch (10), an operating hours counter (3), a bar handle (1) and wheels (4). Two rubber feet (6) prevent the device from rolling away.

The device can reduce the relative humidity of a room to approx. 35 %. Due to the heat radiation generated during operation, the room temperature may rise by approx. 1–3 °C.

Device depiction and operating elements

Standard scope of delivery• TTK 400 with bar handle• Air filter• Condensation drain hose• Operating manual

Optional accessories• Hygrostat• Condensate pump• Energy cost gauge

Information about the device

No. Operating element

1 Bar handle2 Air inlet3 Operating hours counter4 Wheels5 Air filter6 Rubber feet7 Condensation drain hose8 Air outlet9 Mains power cable10 Mains switch

1

5

10

2

3

4

8

7

9

6


Technical data

Power consumptionThe device's power consumption depends on the current room temperature and relative humidity. Multiply the operating hours (see operating hours counter (3)) by a consumption value of one kilowatt per hour to determine the approximate power consumption.To determine the precise power consumption, an optionally available energy cost gauge can be connected between the construction dryer and the power source. Contact your Trotec customer service.

Parameter Value

Model TTK 400Dehumidification performance, max. 75 l / 24 hDehumidification performance (20 °C / 60 % relative humidity) 30 l / 24 hSuitable for room dimensions up to:Construction drying or water damage clearanceDry keeping

400 m³800 m³

Operating temperature 0–40 °CWorking range for relative humidity 35–100 %Air flow rate, max. 420 m³/hElectric connection 230 V / 50 Hz / 6.85 APower consumption, max. 1.4 kWPower consumption, average 1 kWFuse (home) 10 ACompressor RotaryRefrigerant R407cAmount of refrigerant 0.45 kgWeight 42 kgDimensions (HxDxW) 854 x 480 x 510 mmMinimum distance to walls or other objects A:

B:C:D:

Top:Rear:Side:Front:

50 cm50 cm50 cm50 cm

Sound pressure level LpA (3 m; complies with DIN 45635-01-KL3) 56 dB(A)


Refrigerant circuit diagram

Circuit diagram

COMP

AIR CONDENSER

VALVE SOLENOID

DRIER

EVAPORATOR

PORT PROCESS

13

4

INTERLOCK

REM

OVE

LINK IF

PUM

PFITTED

HO

UR

S RU

NM

ETER

2(NO

)

6(NO

)51A1

A2

2112H(N

/C)

C(C

OM

)

C(C

OM

)

(N/C

)L

32

1

(CO

M)

2

(N/O

)

(N/C

)

MAKES 1-3 O

NTEM

P FALLING

MAIN

S LAMP

CO

NTR

OL

SWITC

H

CO

NTR

OL FU

SE

DEFR

OST VALVE

DEFR

OST

THER

MO

STAT

FAN MODE SWITCH

CYCLE FAULT LAMP

LP SWITC

HBR

EAKS ON

PRESSU

RE FALLIN

G

HP SW

ITCH

BREAKS O

NPR

ESSUR

E RISIN

G

INTERLOCK

DEFR

OST LAM

P

FAN M

OTO

R

FAN C

AP'

HU

MID

ISTAT

HIG

H AIR

LIM

IT STAT

DELAY

TIMER

CO

NTAC

TOR

CO

MPR

ESSOR

CO

ND

ENSATE

PUM

P (IF FITTED

) PU

MP FU

SE

RU

N

CAP

SOFT STAR

T (IF FITTED

)

RELAY/H

ARD

STAR

T CAP

(IF FITTED

)

L N

C

S R

CONT

1


TB8

AS

PE

N

PU

MP

230V

CS R

CO

MP

RE

SS

OR

R

UN

CA

P

FAN

M

OTO

R

1 4

2 3

SO

LEN

OID

V

ALV

E

DE

FRO

ST

CO

NTR

OL

STA

T

ISO

LATO

R

ON

/OFF

SW

ITC

H

2 1

4 3

HU

MID

ISTA

T IF

FIT

TED

N

L N

PU

RG

E P

US

HB

UTT

ON

HIG

H

LEV

EL

FLO

AT

SW

ITC

H

LOW

LE

VE

L FL

OA

T S

WIT

CH

AS

PE

N P

UM

P K

IT O

PTI

ON

HA

RD

STA

RT

CA

P

IF F

ITTE

D

21

ISS

C/N

APP

DD

ATE

MA

TER

IAL

FIN

ISH

TOLE

RAN

CE

UN

LES

S S

PEC

IFIE

D

HO

LES

TO B

S 45

00 E

12

INS

PEC

TIO

N L

EV

ELD

IMS

SH

T N

o.C

ON

T'D

RA

WN

ALL

SH

AR

P E

DG

ES A

ND

BU

RR

S T

O B

E R

EM

OVE

D

DR

G N

o.

APP

RO

VED

DA

TES

CA

LE

DO

NO

T SC

ALE

PR

INT

3rd

AN

GLE

PR

OJE

CTI

ON

IF IN

DO

UBT

AS

K

TITL

E

DR

G N

o.

DR

AW

ING

CH

AN

GE

1394

KW

1

9/01

/10

kW H

OU

RS

ME

TER

BLU

E1.0

WHITE 1.0

GREY 1.0

NL

OU

TL IN

BLUE 1.0

kW H

OU

RS

ME

TER

GR

EY1.

0

32

41

PLU

G

BLACK

BLACK

BROWN

BLUE

GREEN/YELLOW

AS

PE

N

PU

MP

HIG

H L

EV

EL

FLO

AT

SW

ITC

H

LOW

LE

VE

L FL

OA

T S

WIT

CH

ASPE

N P

UM

P K

IT

IF F

ITTE

D

GR

EE

N/Y

ELL

OWR

ED

BR

OW

N

BLU

E

BLA

CK

BR

OW

N

BLA

CK

BLA

CK

PU

RG

E

SW

ITC

H 1 2

32

41

SO

CK

ET

BLUE1.0

GREEN/YELLOW 1.0

BROWN1.0

WHITE 1.0

32

41

BR

OW

N

1.0

CO

MP

RE

SS

OR

RE

MO

VE

PLU

G A

ND

FIT

PU

MP

KIT

PLU

G IF

FIT

TED

RE

D 1

.0 L

INKB

LUE

1.0

TB12

TB11

M/C

P

LUG

REM

OVE

& R

EPL

AC

EW

ITH

PU

MP

PLU

G

IF F

ITTE

D

PUM

PP

LUG

TB10

TB9

WH

ITE

1.0

B

RO

WN

1.0

RE

MO

VE

WH

EN

HU

MID

ISTA

T FI

TTE

D

1 2 3

4

DE

FRO

ST C

ON

TRO

L

BAS

E PL

ATE

C

RS

CO

MP

RES

SOR

PINK 1,0

BLACK 1,0

BLUE 1,0

BLU

E 1,

0

CA

PAC

ITO

R

(RU

N)

RED

1.0

GREEN/YELLOW 1.5

BLUE 1,0

BLUE 1,0

HA

RD

S

TAR

T C

AP' FL

YIN

G L

EAD

FL

YIN

G L

EAD

KLIX

ON

2 1

4 3

BLU

E 2.

5BR

OW

N 2

.5

ISO

LATO

R

RED 1.0

GREEN/YELLOW 1.5

BLA

CK

1.0

RED 1.0

BLUE 1.0

EAR

TH

STA

T

8 9 10 11

12

WH

ITE

1.0

BLU

E 1

.0

ORANGE 1.0

HU

MID

ISTA

T KI

T (S

A64

3572

01)

OP

TIO

N

WH

ITE

1.0

PIN

K 1

.0 L

INK

BROWN 1.0

OR

ANG

E 1

.0

IF F

ITTE

D

BLUE FLYING LEAD

SO

LEN

OID

V

ALVE

V

ALVE

BLUE FLYING LEAD BLUE FLYING LEAD

BLUE FLYING LEAD

BROWN FLYING LEAD

GREEN/YELLOW FLYING LEAD

FAN

MO

TOR

230V MAINS SUPPLY

ENLB

RO

WN

2.5 B

LUE

2.5

GR

EEN

/YE

LLO

W 1

.5

RE

D1.

0

BLU

E 1

.0

BLA

CK

1.0

BLU

E1.

0

7 6 5 4 3 2 1

WH

ITE

D35

3153

WIR

ING

DIA

GR

AM

D35

3153

1 /

KW

19/0

1/10

N/A

1

INIT

IAL

ISS

UE

LABEL D353253 ISS 1


To make the device easier to transport, it is fitted with wheels and a bar handle. If necessary, transport the device with the help of another person. To lift the device, use a fork lift or pallet jack.Before transporting the device, observe the following:

1. Switch off the device at the mains switch (see chapter Operat-ing elements).

2. Remove the mains plug from the mains socket. Do not use the power cable to drag the device!

3. Empty the condensation drain hose or the condensate pump (optional). Check for dripping condensation.

4. Hold the bar handle in both hands and carefully tilt the device.5. Transport the device on its wheels.

After transporting the device, observe the following:1. Set up the device in an upright position after transport.2. Make sure that the two rubber feet are placed level on the

ground. The rubber feet lock the device and prevent it from rolling away.

Adjusting the bar handleDepending on your requirements, the bar handle can be installed horizontally or vertically. To adjust the bar handle, carry out the following steps on both sides of the device:1. Loosen screw (15).2. Remove screws (16) and (17). 3. Turn the bar handle by 90°. 4. Insert screws (16) and (17) in the other position.5. Tighten all screws (15, 16, 17).

StorageWhen out of use, store the device as follows:• dry,• under a roof,• in an upright position where it is protected from dust and direct

sunlight,• with a plastic cover to protect it from invasive dust, if neces-

sary.• The storage temperature is the same as the range given for the

operating temperature in the chapter Technical data.

Transport

15

16

15

16

A.

B.

17

17


• After being switched on, the device operates fully automatical-ly.

• Avoid open doors and windows.

PositioningWhen positioning the device, observe the minimum distance from walls and other objects specified in the chapter Technical data.

• Set the device up in a level and stable position.• When positioning the device, keep a sufficient distance to heat

sources.• If possible, set up the device in the middle of a room. When us-

ing several devices, make sure that the distance between them is the same.

• When positioning the device, particularly in wet areas, secure it locally with an RCD (residual current device) which complies with the respective regulations.

• Make sure that extension cables are completely unrolled.• Make sure that the power supply's voltage and current comply

with the specifications on the device's nameplate.• When using a generator, ensure that the generator supplies at

least 4 kW (The device's start-up current can exceed the nom-inal current by four or five times. Also note this fact when using several devices at one generator).

Notes regarding the dehumidification performanceThe dehumidification performance depends on:• the layout of the room• the room temperature• the relative humidity

The higher the room temperature and relative humidity, the greater the dehumidification performance.For operation in living rooms, a relative humidity of approx. 50–60 % is sufficient. In store rooms and archives, the humidity should not exceed approx. 50 %.

Operating elements

Operation

CC

A

B

D

No. Operating element

3 Operating hours counter10 Mains switch:

ON: The device is switched on.OFF: The device is switched off.

310


Start-upInserting the air filter

Positioning the condensation drain hose

Note:The condensation drain hose is already installed when the device is delivered.

1. Ensure that the condensation drain hose is properly connected to the device and is free of damage.

2. Depending on the application, position the end of the conden-sation drain hose as follows:– Place a sufficiently dimensioned container (at least 90 litres)

beside the device and insert the hose end. Check the filling level of the container regularly.

– Position the end of the condensation drain hose above a wa-ter drain. For larger distances, a longer hose of the same type can also be used.

– The device can also be operated with a condensate pump. Contact your Trotec customer service.

3. Ensure that the condensation drain hose always descends.

16x1 mm


Switching the device on1. Ensure that the condensation drain hose (7) has been laid and

connected properly. Do not create tripping hazards.2. Ensure that the condensation drain hose (7) is not kinked or

jammed and that there are no objects on the condensation drain hose (7).

3. Ensure that the condensation can run off properly.4. Insert the mains plug into a properly secured mains socket. Do

not create tripping hazards.5. Switch on the device at the mains switch (10).

Continuous operation modeIn continuous operation mode, the device dehumidifies the air constantly, regardless of the humidity in the air.

Hygrostat operation mode (optional)The device can also be operated with a hygrostat. The hygrostat switches the device on or off depending on the rel-ative humidity.If you choose to operate the device with an optional hygrostat, set the desired relative humidity at the hygrostat (see operating man-ual of the optional hygrostat).

Automatic defrostDepending on the air temperature and the relative humidity, the evaporator fins may freeze. The hot gas automatic defrost installed in the device switches back on as needed. Dehumidifica-tion mode is briefly interrupted during defrosting.

Shutdown1. Switch off the device at the mains switch (10).2. Remove any condensate from the device by pressing the but-

ton for draining residual water from the condensate pump (op-tional).

3. Do not touch the mains plug with wet or damp hands.4. Remove the mains plug from the mains socket.5. Remove the condensation drain hose (7) and any residual fluid

from it.6. Clean the device, and especially the air filter, according to the

chapter Maintenance.7. Store the device according to the chapter Storage.

D I I M

U

H

S T A

40%

30%

20%

60%

80%

OFF

O

N

T

D I I M

U

H

S T A

40%

30%

20%

60%

80%

OFF

O

N

T


The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.

Caution!To prevent damages to the device and to prevent the fuses or motor protection switches from tripping, make sure that the device is switched off and wait for at least 5 minutes before switching the device back on.

The device does not start:• Check the mains connection (230 V/1~/50 Hz).• Check the mains plug for damages.• Check whether the mains switch (10) is in the ON position.• Check the fuse (home).• If you operate the device with a hygrostat, check the desired

relative humidity. The humidity in the room must be above the selected range. Reduce the selected relative humidity.

• Have the electrical equipment checked by a specialist compa-ny for cooling and air-conditioning or by Trotec.

The device is running, but no condensate forms:• Check whether the condensation drain hose is positioned cor-

rectly.• Check whether the condensate pump (optional) functions

properly. Check for abnormal vibrations and sounds. Remove external dirt.

• Check the room temperature. Observe the device's permissi-ble operating range according to the technical data.

• Ensure that the relative humidity complies with the technical data.

• If you operate the device with a hygrostat, check the desired relative humidity. The humidity in the room must be above the selected range. Reduce the selected relative humidity.

• Check the air filter for dirt. If necessary, clean or replace the air filter.

The device is loud or vibrates; condensate is leaking:• Check whether the device is standing upright and on an even

surface.

The device gets very warm, is loud or loses power:• Check the air inlets and air filter for dirt. Remove external dirt.• Check the inside of the device for dirt (see chapter Mainte-

nance). Clean the inside of the device as described in the chap-ter Cleaning the inside with compressed air.

Your device still does not operate correctly after these checks? Bring the device to a specialist company for cooling and air-con-ditioning or to Trotec for repair.

Errors and faults


Maintenance intervals

Maintenance and care logDevice type: ........................................ Device number: ........................................

Maintenance

Maintenance and care intervalbefore every start-up

as neededat least every 2 weeks

at least every 4 weeks

at least every 6 months

at least annu-ally

Empty the condensate pump, condensation tray and/or construction dryer X

Check the air inlets and outlets for dirt and foreign objects and clean if necessary X X X

Visually check the inside of the device for dirt X XClean the inside with compressed air X XCheck the air inlet grid and air filter for dirt and foreign objects and clean or replace if necessary X X

Replace the air filter XCheck for damage XCheck the attachment screws X XTest run X

Maintenance and care interval 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Check the air inlets and outlets for dirt and foreign objects and clean if necessaryClean the exteriorVisually check the inside of the device for dirtClean the inside with compressed airCheck the air inlet grid and air filter for dirt and foreign objects and clean or replace if necessaryReplace the air filterCheck for damageCheck the attachment screwsTest runRemarks:

1. Date:Signature:

2. Date:Signature:

3. Date:Signature:

4. Date:Signature:

5. Date:Signature:

6. Date:Signature:

7. Date:Signature:

8. Date:Signature:

9. Date:Signature:

10. Date:Signature:

11. Date:Signature:

12. Date:Signature:

13. Date:Signature:

14. Date:Signature:

15. Date:Signature:

16. Date:Signature:


Activities required before starting maintenance1. Do not touch the mains plug with wet or damp hands.2. Before any work, remove the mains plug!

Maintenance tasks at the electrical equipment or the air-conditioning technology must only be carried out by specialist companies for cooling and air-conditioning or by Trotec.

Visually check the inside of the device for dirt1. Remove the air filter (see chapter Cleaning the air inlets and

the air filter).2. Use a torch to illuminate the openings of the device.3. Check the inside of the device for dirt.4. If you find dirt, use a high-pressure cleaner to clean the device

according to the chapter Cleaning the air inlets and the air fil-ter.

5. Put the air filter back in.

Cleaning the air inlets and the air filter

Caution!After having cleaned the device with a high-pressure cleaner, check the air filter removed beforehand for damages. The corners and edges of the air filter must not be deformed or rounded.Before reinserting the air filter, make sure that it is undamaged and dry!Read the chapter Maintenance intervals and replace the air filter in due time!

A.

B.

90°

D.

50 cm

50 cm

C.


Cleaning the inside with compressed air

A.

B.

C.


Overview and list of spare partsMain components

46 REFRIGERANT

3

6

7

2

4

5

31

32

54

52

484941

44

1 O

8

45

43

42

35

47 4700000.0

00000.0

h

kWh

PLAN VIEW TOP

11

12

61

i40

9 101

22

21

PLAN VIEW BASE

IMPORTANT

COMPRESSOR FEETFIXING DETAIL(IN 3 POS'NS)

NYLON WASHER MUST BE FITTED

17

BASE

COMPRESSORFOOT

64

PART VIEW SHOWING COMPRESSOR THERMAL OVERLOAD/

TERMINAL COVER ASSY.

70 69

66

67

65 68

Note!The position numbers of the spare parts differ from those describing the positions of other parts mentioned in this operating manual.

No. Article number Spare part No. Article number Spare part

1 7242000915 base plate C/W spindle 42 7242000925 side panel2 SA521903 drip tray assembly 43 7242000927 side panel (bottom)3 7162000193 evaporator/condenser assembly 44 7242000926 side panel (top)4 7161000197 rotary compressor QXC-19k 45 7140000900 operating hours counter and energy meter5 7242000924 side panel (air in) 46 SP182554 refrigerant R407c6 7242000922 side panel (air out) 47 SD314650 recess handle7 7600000081 wheel 200 mm diameter 48 7140001337 defrost valve body8 SD356350 cover plate 49 7420001338 solenoid coil9 SD519406 pipe run (discharge) 52 7242000923 inlet grille10 SD519405 pipe run (suction) 54 SD476250 plug securing bracket11 7110000919 fan motor 34 61 7242000921 outlet grille12 7241000917 fan blade 10 1/2" 5 blade 64 7300001250 compressor rubber mount17 SD520852 spacer 37 mm LG 10 mm O/D 8.20 mm I/D 65 7140001298 thermal overload21 7310000005 M20 plastic gland back nut 66 SD622952 compressor terminal gasket22 7333000378 plug/lead assembly 67 SD622953 terminal cover31 7220000195 dryer molecular sieve 68 SD622954 spring (thermal overload)32 7220000358 capillary tubes 0.090" OD x 0.052 ID x 64" 69 SD622955 nut and bolt set35 SD364151 handle 70 SD622956 rubber washer40 SD533251 user manual41 7242000920 top cover


Condensation tray

SEE FIG 1.

LOOM ASSY

TERMINATE SWITCH WITH BRACKET TO LOOM ASSY

TERMINAL BLOCK PART OF LOOM ASSY

1

2

4 10

7

3

HARD START CAPACITOR

IF FITTED

OFF

ON

230V VERSION

DUAL VOLTAGE VERSION

1 O

2

Note!The position numbers of the spare parts differ from those describing the positions of other parts mentioned in this operating manual.

No. Article number Spare part

1 SD512050 drip tray2 7140000928 defrost control stat3 7140000353 run capacitor 30 μF 440 V4 SD073150 hard start cap/relay7 7130000918 rotary switch 2 pole on/off9 SA356403 loom assembly AX17 SD369350 pipe insert bung


In the European Union, electronic equipment must not be treated as domestic waste, but must be disposed of professionally in accordance with Directive 2002/

96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE). At the end of its life, please dispose of this device accord-ing to the relevant legal requirements.

The device uses an environmentally friendly and ozone-neutral refrigerant (see chapter Technical data). Dispose of the refriger-ant/oil mixture appropriately and according to the national regula-tions.

in accordance with the EC Low Voltage Directive 2006/95/EC and the EC Directive 2004/108/EC about electromagnetic compatibil-ity.Herewith, we declare that the dehumidifier TTK 400 was devel-oped, constructed and produced in compliance with the named EC directives.

Applied standards:EN 60335-2-40:2003EN 12100-1:2003EN 12100-2:2003EN 55014-1:2000EN 6100-4-2,4,5,6:1997EN 294:1992EN 418:1992

The marking is found on the device nameplate.

Manufacturer: Trotec GmbH & Co. KGGrebbener Straße 7D-52525 HeinsbergPhone: +49 2452 962-400Fax: +49 2452 962-200E-mail: [email protected]

Heinsberg, 27/11/2006

Managing Director: Detlef von der Lieck

Disposal Declaration of conformity


Trotec GmbH & Co. KG

Grebbener Str. 7 D-52525 Heinsberg

+49 2452 962-400 +49 2452 962-200

[email protected] www.trotec.com

ba ttk 400 - satema€¦ · en operating manual – dehumidifier ttk 400 4 technical data power...

Documents